Κάρτα TV - Kworld KW-DVBT 323U

[logari81]

το πρωτο απο τα 2 ειναι η κάρτα τηλεόρασης. Επέλεξέ το και παιξε λιγο με τις ρυθμίσεις του. Αν δεν τα καταφερεις μπορεις να με βρεις εδώ:
http://www.ubuntu-gr.org/webchat

[harriscarouzos]

[harriscarouzos]

βασικα βρηκα καποια λυση σε ενα άλλο topic και εκανα τα εξης:
sudo apt-get install sox
sudo apt-get install libsox-fmt-oss
τρεχω το tv time και μετα απο το terminal για ηχο:
sox --channels 2 -s --rate 48000 --type ossdsp /dev/dsp1 --type ossdsp /dev/dsp

τώρα εχω ηχο, αλλα οχι κ τοσο ικανοποιητικο σε μερικα καναλια.
το μονο κακο ειναι οτι δεν μπορω να ρυθμισω την ενταση του ηχου παρα μονο απο τα ηχεια.
tespa μην τα θελω κ ολα δικα μου!
thanks παντως

[logari81]

βασικα βρηκα καποια λυση σε ενα άλλο topic και εκανα τα εξης:
sudo apt-get install sox
sudo apt-get install libsox-fmt-oss
τρεχω το tv time και μετα απο το terminal για ηχο:
sox --channels 2 -s --rate 48000 --type ossdsp /dev/dsp1 --type ossdsp /dev/dsp

μπράβο αυτό εννοούσα πριν.

[harriscarouzos]

το μονο που δεν εχει απαντηθει ειναι τι γινεται με τα ψηφιακα κανάλια? Σε ενα αλλο topic ενας φιλος μπορεσε να τα δει με το Kaffeine. Δυστυχως εγω όχι. Μηπως υπαρχει καποιο αλλο προγραμμα να κανω μια προσπαθεια ακομα?

[logari81]

δεν χερω αν το tvtime υποστηριζει ψηφιακά κανάλια ψάξτο λίγο στην σελίδα τους. Πάντως πιθανόν να σε βοηθήσει το πακέτο dvb-utils και εκτος αυτού δώσε μας το αποτελεσμα των εντολών

Κώδικας: Επιλογή όλων

lsmod
dmesg


παλι

http://wiki.ubuntuusers.de/em28xx

[idomeneas]

βασικα βρηκα καποια λυση σε ενα άλλο topic και εκανα τα εξης:
sudo apt-get install sox
sudo apt-get install libsox-fmt-oss
τρεχω το tv time και μετα απο το terminal για ηχο:
sox --channels 2 -s --rate 48000 --type ossdsp /dev/dsp1 --type ossdsp /dev/dsp

τώρα εχω ηχο, αλλα οχι κ τοσο ικανοποιητικο σε μερικα καναλια.
το μονο κακο ειναι οτι δεν μπορω να ρυθμισω την ενταση του ηχου παρα μονο απο τα ηχεια.
tespa μην τα θελω κ ολα δικα μου!
thanks παντως

Μπορείς για τον ήχο, να παίξεις με την τιμή του rate, δηλαδή δοκίμασε να βάλεις 32000 αντί για 48000. Αυτό ίσως να τα βελτιώσει τα πράγματα.

[harriscarouzos]

Κώδικας: Επιλογή όλων

[ 0.143582] PnPBIOS: Disabled by ACPI PNP
[ 0.143609] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[ 0.143617] system 00:08: ioport range 0x800-0x87f has been reserved
[ 0.143623] system 00:08: ioport range 0x480-0x4bf has been reserved
[ 0.143630] system 00:08: iomem range 0xfed20000-0xfed8ffff has been reserved
[ 0.143636] system 00:08: iomem range 0xff380000-0xffefffff has been reserved
[ 0.143648] system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.143655] system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.143667] system 00:0b: ioport range 0x680-0x6ff has been reserved
[ 0.143674] system 00:0b: ioport range 0x295-0x296 has been reserved
[ 0.143686] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[ 0.143693] system 00:0c: iomem range 0xc0000-0xdffff could not be reserved
[ 0.143699] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
[ 0.143705] system 00:0c: iomem range 0x100000-0x4fffffff could not be reserved
[ 0.143711] system 00:0c: iomem range 0xfff00000-0xffffffff has been reserved
[ 0.178606] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.178613] pci 0000:00:01.0: IO window: 0xa000-0xafff
[ 0.178621] pci 0000:00:01.0: MEM window: 0xff000000-0xff0fffff
[ 0.178629] pci 0000:00:01.0: PREFETCH window: 0xcff00000-0xefefffff
[ 0.178639] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
[ 0.178645] pci 0000:00:1e.0: IO window: 0xb000-0xbfff
[ 0.178653] pci 0000:00:1e.0: MEM window: 0xff100000-0xff1fffff
[ 0.178659] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.178686] pci 0000:00:1e.0: setting latency timer to 64
[ 0.178695] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.178700] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.178705] pci_bus 0000:01: resource 0 io: [0xa000-0xafff]
[ 0.178709] pci_bus 0000:01: resource 1 mem: [0xff000000-0xff0fffff]
[ 0.178714] pci_bus 0000:01: resource 2 pref mem [0xcff00000-0xefefffff]
[ 0.178719] pci_bus 0000:02: resource 0 io: [0xb000-0xbfff]
[ 0.178724] pci_bus 0000:02: resource 1 mem: [0xff100000-0xff1fffff]
[ 0.178728] pci_bus 0000:02: resource 3 io: [0x00-0xffff]
[ 0.178733] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
[ 0.178797] NET: Registered protocol family 2
[ 0.178976] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.179626] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.180927] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.181616] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.181622] TCP reno registered
[ 0.181849] NET: Registered protocol family 1
[ 0.182005] pci 0000:01:00.0: Boot video device
[ 0.182291] cpufreq-nforce2: No nForce2 chipset.
[ 0.182342] Scanning for low memory corruption every 60 seconds
[ 0.182546] audit: initializing netlink socket (disabled)
[ 0.182567] type=2000 audit(1276344755.179:1): initialized
[ 0.194214] Trying to unpack rootfs image as initramfs...
[ 0.208235] highmem bounce pool size: 64 pages
[ 0.208246] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.210970] VFS: Disk quotas dquot_6.5.2
[ 0.211091] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.216134] fuse init (API version 7.13)
[ 0.216346] msgmni has been set to 1709
[ 0.220328] alg: No test for stdrng (krng)
[ 0.220518] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.220526] io scheduler noop registered
[ 0.220529] io scheduler anticipatory registered
[ 0.220532] io scheduler deadline registered
[ 0.220619] io scheduler cfq registered (default)
[ 0.220824] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.220869] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.221042] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.221050] ACPI: Power Button [PWRB]
[ 0.221138] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.221144] ACPI: Power Button [PWRF]
[ 0.221748] processor LNXCPU:00: registered as cooling_device0
[ 0.230597] isapnp: Scanning for PnP cards...
[ 0.240394] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.240524] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.240669] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 0.241250] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.243116] brd: module loaded
[ 0.248179] loop: module loaded
[ 0.248377] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 0.248575] ata_piix 0000:00:1f.1: version 2.13
[ 0.248601] alloc irq_desc for 18 on node -1
[ 0.248606] alloc kstat_irqs on node -1
[ 0.248617] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.248689] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 0.292434] scsi0 : ata_piix
[ 0.292652] scsi1 : ata_piix
[ 0.295805] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
[ 0.295813] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
[ 0.296547] Fixed MDIO Bus: probed
[ 0.296615] PPP generic driver version 2.4.2
[ 0.296730] tun: Universal TUN/TAP device driver, 1.6
[ 0.296735] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.296924] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.296971] alloc irq_desc for 23 on node -1
[ 0.296975] alloc kstat_irqs on node -1
[ 0.296987] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 0.297014] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.297020] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.297097] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 0.297143] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.301044] ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
[ 0.308034] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xff27fc00
[ 0.328401] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.328655] usb usb1: configuration #1 chosen from 1 choice
[ 0.328714] hub 1-0:1.0: USB hub found
[ 0.328733] hub 1-0:1.0: 8 ports detected
[ 0.328850] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.328880] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.328958] alloc irq_desc for 16 on node -1
[ 0.328962] alloc kstat_irqs on node -1
[ 0.328974] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.328990] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.328996] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.329089] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.329138] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000e000
[ 0.329327] usb usb2: configuration #1 chosen from 1 choice
[ 0.329382] hub 2-0:1.0: USB hub found
[ 0.329400] hub 2-0:1.0: 2 ports detected
[ 0.329477] alloc irq_desc for 19 on node -1
[ 0.329482] alloc kstat_irqs on node -1
[ 0.329493] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.329505] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.329512] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.329590] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 0.329634] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e400
[ 0.329809] usb usb3: configuration #1 chosen from 1 choice
[ 0.329863] hub 3-0:1.0: USB hub found
[ 0.329880] hub 3-0:1.0: 2 ports detected
[ 0.329961] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.329974] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.329981] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.330062] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 0.330104] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800
[ 0.330293] usb usb4: configuration #1 chosen from 1 choice
[ 0.330347] hub 4-0:1.0: USB hub found
[ 0.330364] hub 4-0:1.0: 2 ports detected
[ 0.330440] uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.330453] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 0.330458] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 0.330542] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 0.330574] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000ec00
[ 0.330751] usb usb5: configuration #1 chosen from 1 choice
[ 0.330805] hub 5-0:1.0: USB hub found
[ 0.330823] hub 5-0:1.0: 2 ports detected
[ 0.331005] PNP: No PS/2 controller found. Probing ports directly.
[ 0.338347] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.338363] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.338636] mice: PS/2 mouse device common for all mice
[ 0.338822] rtc_cmos 00:02: RTC can wake from S4
[ 0.338907] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 0.338944] rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
[ 0.339164] device-mapper: uevent: version 1.0.3
[ 0.344391] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.344538] device-mapper: multipath: version 1.1.0 loaded
[ 0.344545] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.344802] EISA: Probing bus 0 at eisa.0
[ 0.344846] EISA: Detected 0 cards.
[ 0.348233] cpuidle: using governor ladder
[ 0.348239] cpuidle: using governor menu
[ 0.349115] TCP cubic registered
[ 0.349361] NET: Registered protocol family 10
[ 0.350210] lo: Disabled Privacy Extensions
[ 0.350765] NET: Registered protocol family 17
[ 0.350870] Using IPI No-Shortcut mode
[ 0.351053] PM: Resume from disk failed.
[ 0.351086] registered taskstats version 1
[ 0.351426] Magic number: 14:340:228
[ 0.351543] rtc_cmos 00:02: setting system clock to 2010-06-12 12:12:35 UTC (1276344755)
[ 0.351549] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.351552] EDD information not available.
[ 0.504480] ata1.00: ATA-6: ST340810A, 3.39, max UDMA/100
[ 0.504488] ata1.00: 78165360 sectors, multi 16: LBA
[ 0.535232] ata1.01: ATA-7: WDC WD2500JB-00REA0, 20.00K20, max UDMA/100
[ 0.535239] ata1.01: 488397168 sectors, multi 16: LBA48
[ 0.584732] ata2.00: ATAPI: _NEC DVD_RW ND-3520A, 1.04, max UDMA/33
[ 0.584797] ata2.01: ATAPI: SONY DVD-ROM DDU1612, DYS1, max UDMA/33
[ 0.585018] ata1.00: configured for UDMA/100
[ 0.592959] ata2.00: configured for UDMA/33
[ 0.593111] ata1.01: configured for UDMA/100
[ 0.593489] ata2.01: configured for UDMA/33
[ 0.843588] usb 1-3: new high speed USB device using ehci_hcd and address 3
[ 0.931639] isapnp: No Plug & Play device found
[ 0.932145] scsi 0:0:0:0: Direct-Access ATA ST340810A 3.39 PQ: 0 ANSI: 5
[ 0.932450] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 0.932694] scsi 0:0:1:0: Direct-Access ATA WDC WD2500JB-00R 20.0 PQ: 0 ANSI: 5
[ 0.932934] sd 0:0:1:0: Attached scsi generic sg1 type 0
[ 0.933227] sd 0:0:0:0: [sda] 78165360 512-byte logical blocks: (40.0 GB/37.2 GiB)
[ 0.933314] sd 0:0:0:0: [sda] Write Protect is off
[ 0.933320] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.933362] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.933819] sda:
[ 0.934591] scsi 1:0:0:0: CD-ROM _NEC DVD_RW ND-3520A 1.04 PQ: 0 ANSI: 5
[ 0.940873] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 0.940882] Uniform CD-ROM driver Revision: 3.20
[ 0.941102] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 0.941228] sr 1:0:0:0: Attached scsi generic sg2 type 5
[ 0.942300] scsi 1:0:1:0: CD-ROM SONY DVD-ROM DDU1612 DYS1 PQ: 0 ANSI: 5
[ 0.947693] sr1: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray
[ 0.947951] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 0.948079] sr 1:0:1:0: Attached scsi generic sg3 type 5
[ 0.964572] sda1 sda2 sda3 <
[ 0.977351] Freeing initrd memory: 7786k freed
[ 0.998711] sda5
[ 0.998839] sd 0:0:1:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 1.011588] usb 1-3: configuration #1 chosen from 1 choice
[ 1.015584] sd 0:0:1:0: [sdb] Write Protect is off
[ 1.015592] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.015622] sda6 >
[ 1.016222] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.016516] sdb: sdb1
[ 1.025993] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.026112] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 1.026135] Freeing unused kernel memory: 656k freed
[ 1.027131] Write protecting the kernel text: 4676k
[ 1.027188] Write protecting the kernel read-only data: 1840k
[ 1.072900] udev: starting version 151
[ 1.364124] usb 2-2: new full speed USB device using uhci_hcd and address 2
[ 1.504144] Floppy drive(s): fd0 is 1.44M
[ 1.524973] FDC 0 is a post-1991 82077
[ 1.534487] usb 2-2: configuration #1 chosen from 1 choice
[ 1.541979] hub 2-2:1.0: USB hub found
[ 1.542918] hub 2-2:1.0: 3 ports detected
[ 1.569900] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 1.569946] 8139cp 0000:02:05.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 1.604916] 8139too Fast Ethernet driver 0.9.28
[ 1.604981] alloc irq_desc for 22 on node -1
[ 1.604986] alloc kstat_irqs on node -1
[ 1.604998] 8139too 0000:02:05.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 1.609341] eth0: RealTek RTL8139 at 0xb800, 00:19:66:62:c3:bc, IRQ 22
[ 1.788048] usb 4-1: new full speed USB device using uhci_hcd and address 2
[ 1.972921] usb 4-1: configuration #1 chosen from 1 choice
[ 2.068062] usbcore: registered new interface driver hiddev
[ 2.077726] input: Microsoft Microsoft® SideWinder™ X5 Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.0/input/input3
[ 2.078416] generic-usb 0003:045E:0736.0001: input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft® SideWinder™ X5 Mouse] on usb-0000:00:1d.2-1/input0
[ 2.078495] usbcore: registered new interface driver usbhid
[ 2.078766] usbhid: v2.6:USB HID core driver
[ 2.125745] usb 2-2.3: new full speed USB device using uhci_hcd and address 3
[ 2.261884] usb 2-2.3: configuration #1 chosen from 1 choice
[ 2.269354] input: Razer Reclusa Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2.3/2-2.3:1.0/input/input4
[ 2.270341] generic-usb 0003:1532:0200.0002: input,hidraw1: USB HID v1.10 Keyboard [Razer Reclusa Keyboard] on usb-0000:00:1d.0-2.3/input0
[ 2.274932] input: Razer Reclusa Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2.3/2-2.3:1.1/input/input5
[ 2.275109] generic-usb 0003:1532:0200.0003: input,hidraw2: USB HID v1.10 Device [Razer Reclusa Keyboard] on usb-0000:00:1d.0-2.3/input1
[ 2.293612] EXT4-fs (sda5): mounted filesystem with ordered data mode
[ 25.021963] Adding 462840k swap on /dev/sda6. Priority:-1 extents:1 across:462840k
[ 25.116253] udev: starting version 151
[ 25.279886] lp: driver loaded but no devices found
[ 25.362594] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 25.618017] Linux agpgart interface v0.103
[ 25.636520] intel_rng: FWH not detected
[ 25.691068] parport_pc 00:07: reported by Plug and Play ACPI
[ 25.691120] parport0: PC-style at 0x378, irq 7 [PCSPP]
[ 25.749244] agpgart-intel 0000:00:00.0: Intel 865 Chipset
[ 25.793675] lp0: using parport0 (interrupt-driven).
[ 26.035231] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xf0000000
[ 26.356128] [drm] Initialized drm 1.1.0 20060810
[ 26.366555] type=1505 audit(1276333981.512:2): operation="profile_load" pid=531 name="/sbin/dhclient3"
[ 26.367350] type=1505 audit(1276333981.512:3): operation="profile_load" pid=531 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 26.367775] type=1505 audit(1276333981.512:4): operation="profile_load" pid=531 name="/usr/lib/connman/scripts/dhclient-script"
[ 26.380937] ppdev: user-space parallel port driver
[ 26.680452] Linux video capture interface: v2.00
[ 26.796094] [drm] radeon defaulting to kernel modesetting.
[ 26.796102] [drm] radeon kernel modesetting enabled.
[ 26.796201] radeon 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 26.814437] [drm] radeon: Initializing kernel modesetting.
[ 26.816123] [drm] register mmio base: 0xFF0F0000
[ 26.816129] [drm] register mmio size: 65536
[ 26.818806] [drm] GPU reset succeed (RBBM_STATUS=0x00000140)
[ 26.818827] [drm] Generation 2 PCI interface, using max accessible memory
[ 26.818844] agpgart-intel 0000:00:00.0: AGP 3.0 bridge
[ 26.818872] agpgart-intel 0000:00:00.0: putting AGP V3 device into 8x mode
[ 26.818922] radeon 0000:01:00.0: putting AGP V3 device into 8x mode
[ 26.818942] [drm] radeon: VRAM 128M
[ 26.818946] [drm] radeon: VRAM from 0x00000000 to 0x07FFFFFF
[ 26.818950] [drm] radeon: GTT 128M
[ 26.818953] [drm] radeon: GTT from 0xF0000000 to 0xF7FFFFFF
[ 26.818988] [drm] radeon: irq initialized.
[ 26.819103] [drm] Detected VRAM RAM=128M, BAR=128M
[ 26.819109] [drm] RAM width 64bits DDR
[ 26.819241] [TTM] Zone kernel: Available graphics memory: 441876 kiB.
[ 26.819246] [TTM] Zone highmem: Available graphics memory: 642200 kiB.
[ 26.819273] [drm] radeon: 128M of VRAM memory ready
[ 26.819277] [drm] radeon: 128M of GTT memory ready.
[ 26.819535] [drm] radeon: cp idle (0x02000603)
[ 26.819712] [drm] Loading R200 Microcode
[ 26.820331] platform radeon_cp.0: firmware: requesting radeon/R200_cp.bin
[ 26.899065] em28xx: New device USB 2883 Device @ 480 Mbps (eb1a:e323, interface 0, class 0)
[ 26.899210] em28xx #0: chip ID is em2882/em2883
[ 26.902117] [drm] radeon: ring at 0x00000000F0000000
[ 26.902142] [drm] ring test succeeded in 0 usecs
[ 26.945131] [drm] radeon: ib pool ready.
[ 26.945269] [drm] ib test succeeded in 0 usecs
[ 26.947314] [drm] Default TV standard: PAL
[ 26.947321] [drm] 27.000000000 MHz TV ref clk
[ 26.947329] [drm] Default TV standard: PAL
[ 26.947331] [drm] 27.000000000 MHz TV ref clk
[ 26.947692] [drm] Radeon Display Connectors
[ 26.947698] [drm] Connector 0:
[ 26.947701] [drm] VGA
[ 26.947707] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[ 26.947710] [drm] Encoders:
[ 26.947713] [drm] CRT1: INTERNAL_DAC1
[ 26.947716] [drm] Connector 1:
[ 26.947719] [drm] S-video
[ 26.947721] [drm] Encoders:
[ 26.947724] [drm] TV1: INTERNAL_DAC2
[ 27.033296] em28xx #0: i2c eeprom 00: 1a eb 67 95 1a eb 23 e3 d0 12 5c 00 6a 22 00 00
[ 27.033316] em28xx #0: i2c eeprom 10: 00 00 04 57 4e 07 01 00 00 00 00 00 00 00 00 00
[ 27.033333] em28xx #0: i2c eeprom 20: 46 00 01 00 f0 10 01 00 00 00 00 00 5b 1e 00 00
[ 27.033350] em28xx #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 10 01 00 00 00 00 00 00
[ 27.033488] em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 27.033504] em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 27.033592] em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 22 03 55 00 53 00
[ 27.033609] em28xx #0: i2c eeprom 70: 42 00 20 00 32 00 38 00 38 00 33 00 20 00 44 00
[ 27.033625] em28xx #0: i2c eeprom 80: 65 00 76 00 69 00 63 00 65 00 00 00 00 00 00 00
[ 27.033641] em28xx #0: i2c eeprom 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 27.033657] em28xx #0: i2c eeprom a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 27.033672] em28xx #0: i2c eeprom b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 27.033688] em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 27.033703] em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 27.033719] em28xx #0: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 27.033735] em28xx #0: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 27.033753] em28xx #0: EEPROM ID= 0x9567eb1a, EEPROM hash = 0xad913442
[ 27.033757] em28xx #0: EEPROM info:
[ 27.033760] em28xx #0: AC97 audio (5 sample rates)
[ 27.033763] em28xx #0: 500mA max power
[ 27.033767] em28xx #0: Table at 0x04, strings=0x226a, 0x0000, 0x0000
[ 27.034849] em28xx #0: Identified as Kworld VS-DVB-T 323UR (card=54)
[ 27.034856] em28xx #0:
[ 27.034858]
[ 27.034945] em28xx #0: The support for this board weren't valid yet.
[ 27.034994] em28xx #0: Please send a report of having this working
[ 27.035043] em28xx #0: not to V4L mailing list (and/or to other addresses)
[ 27.035046]
[ 27.077966] tvp5150 1-005c: chip found @ 0xb8 (em28xx #0)
[ 27.143770] tuner 1-0061: chip found @ 0xc2 (em28xx #0)
[ 27.284865] xc2028 1-0061: creating new instance
[ 27.284873] xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner
[ 27.284892] usb 1-3: firmware: requesting xc3028-v27.fw
[ 27.313392] xc2028 1-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7
[ 27.318439] type=1505 audit(1276333982.464:5): operation="profile_load" pid=690 name="/usr/share/gdm/guest-session/Xsession"
[ 27.366287] type=1505 audit(1276333982.512:6): operation="profile_replace" pid=692 name="/sbin/dhclient3"
[ 27.367113] type=1505 audit(1276333982.512:7): operation="profile_replace" pid=692 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 27.367561] type=1505 audit(1276333982.512:8): operation="profile_replace" pid=692 name="/usr/lib/connman/scripts/dhclient-script"
[ 27.368070] xc2028 1-0061: Loading firmware for type=BASE (1), id 0000000000000000.
[ 27.437873] type=1505 audit(1276333982.584:9): operation="profile_load" pid=694 name="/usr/bin/evince"
[ 27.441250] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 27.522479] type=1505 audit(1276333982.668:10): operation="profile_load" pid=694 name="/usr/bin/evince-previewer"
[ 27.598408] [drm] fb mappable at 0xE0040000
[ 27.598415] [drm] vram apper at 0xE0000000
[ 27.598419] [drm] size 8294400
[ 27.598422] [drm] fb depth is 24
[ 27.598425] [drm] pitch is 7680
[ 27.623708] type=1505 audit(1276333982.768:11): operation="profile_load" pid=694 name="/usr/bin/evince-thumbnailer"
[ 27.689061] alloc irq_desc for 17 on node -1
[ 27.689066] alloc kstat_irqs on node -1
[ 27.689079] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 27.689138] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 27.749836] fb0: radeondrmfb frame buffer device
[ 27.749842] registered panic notifier
[ 27.749856] [drm] Initialized radeon 2.0.0 20080528 for 0000:01:00.0 on minor 0
[ 27.766973] vga16fb: initializing
[ 27.766985] vga16fb: mapped to 0xc00a0000
[ 27.766994] vga16fb: not registering due to another framebuffer present
[ 28.051736] intel8x0_measure_ac97_clock: measured 89689 usecs (4315 samples)
[ 28.051742] intel8x0: clocking to 48000
[ 28.145456] Console: switching to colour frame buffer device 240x67
[ 28.594269] xc2028 1-0061: Loading firmware for type=(0), id 000000000000b700.
[ 28.613935] SCODE (20000000), id 000000000000b700:
[ 28.613948] xc2028 1-0061: Loading SCODE for type=MONO SCODE HAS_IF_4320 (60008000), id 0000000000008000.
[ 28.796199] em28xx #0: Config register raw data: 0xd0
[ 28.797322] em28xx #0: AC97 vendor ID = 0xffffffff
[ 28.797696] em28xx #0: AC97 features = 0x6a90
[ 28.797701] em28xx #0: Empia 202 AC97 audio processor detected
[ 28.892415] tvp5150 1-005c: *** unknown tvp5150 chip detected.
[ 28.892423] tvp5150 1-005c: *** Rom ver is 4.140
[ 28.997294] em28xx #0: v4l2 driver version 0.1.2
[ 29.051740] em28xx #0: V4L2 video device registered as /dev/video0
[ 29.051747] em28xx #0: V4L2 VBI device registered as /dev/vbi0
[ 29.068194] usbcore: registered new interface driver em28xx
[ 29.068202] em28xx driver loaded
[ 29.072940] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 29.072949] vboxdrv: Successfully done.
[ 29.072953] vboxdrv: Found 1 processor cores.
[ 29.078935] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 29.078942] vboxdrv: Successfully loaded version 3.1.6_OSE (interface 0x00100001).
[ 29.166085] em28xx-audio.c: probing for em28x1 non standard usbaudio
[ 29.166094] em28xx-audio.c: Copyright (C) 2006 Markus Rechberger
[ 29.191469] Em28xx: Initialized (Em28xx Audio Extension) extension
[ 35.336055] end_request: I/O error, dev fd0, sector 0
[ 35.420062] end_request: I/O error, dev fd0, sector 0
[ 38.104030] eth0: no IPv6 routers present
[10468.357002] UDF-fs: Partition marked readonly; forcing readonly mount
[10468.386476] UDF-fs INFO UDF: Mounting volume 'My DVD', timestamp 2009/06/22 08:26 (10b4)
[11800.580511] tvp5150 1-005c: *** unknown tvp5150 chip detected.
[11800.580519] tvp5150 1-005c: *** Rom ver is 4.140
[11800.796055] xc2028 1-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000.
[11801.733710] (0), id 00000000000000ff:
[11801.733718] xc2028 1-0061: Loading firmware for type=(0), id 0000000100000007.
[11801.747705] xc2028 1-0061: Loading SCODE for type=MONO SCODE HAS_IF_5320 (60008000), id 0000000f00000007.
[11820.491211] xc2028 1-0061: Loading firmware for type=(0), id 0000000000000010.
[11820.505575] xc2028 1-0061: Loading SCODE for type=SCODE HAS_IF_6240 (60000000), id 0000000000000010.
[11821.591921] (0), id 00000000000000ff:
[11821.591929] xc2028 1-0061: Loading firmware for type=(0), id 0000000100000007.
[11821.606538] xc2028 1-0061: Loading SCODE for type=MONO SCODE HAS_IF_5320 (60008000), id 0000000f00000007.
[11826.351307] xc2028 1-0061: Loading firmware for type=(0), id 0000000000000010.
[11826.365550] xc2028 1-0061: Loading SCODE for type=SCODE HAS_IF_6240 (60000000), id 0000000000000010.
[11827.811203] (0), id 00000000000000ff:
[11827.811211] xc2028 1-0061: Loading firmware for type=(0), id 0000000100000007.
[11827.825794] xc2028 1-0061: Loading SCODE for type=MONO SCODE HAS_IF_5320 (60008000), id 0000000f00000007.
[14858.899958] xc2028 1-0061: Loading firmware for type=(0), id 0000000000000010.
[14858.915968] xc2028 1-0061: Loading SCODE for type=SCODE HAS_IF_6240 (60000000), id 0000000000000010.
[14861.263695] (0), id 00000000000000ff:
[14861.263703] xc2028 1-0061: Loading firmware for type=(0), id 0000000100000007.
[14861.279446] xc2028 1-0061: Loading SCODE for type=MONO SCODE HAS_IF_5320 (60008000), id 0000000f00000007.
[14861.795676] xc2028 1-0061: Loading firmware for type=(0), id 0000000000000010.
[14861.810791] xc2028 1-0061: Loading SCODE for type=SCODE HAS_IF_6240 (60000000), id 0000000000000010.
[14864.979349] (0), id 00000000000000ff:
[14864.979357] xc2028 1-0061: Loading firmware for type=(0), id 0000000100000007.
[14864.994590] xc2028 1-0061: Loading SCODE for type=MONO SCODE HAS_IF_5320 (60008000), id 0000000f00000007.
[14947.201113] xc2028 1-0061: Loading firmware for type=(0), id 0000000000000010.
[14947.217938] xc2028 1-0061: Loading SCODE for type=SCODE HAS_IF_6240 (60000000), id 0000000000000010.
[42193.640057] usb 4-2: new full speed USB device using uhci_hcd and address 3
[42193.833892] usb 4-2: configuration #1 chosen from 1 choice
[42194.278115] usblp0: USB Bidirectional printer dev 3 if 1 alt 0 proto 2 vid 0x03F0 pid 0x7D04
[42194.278176] usbcore: registered new interface driver usblp
[42195.316365] usb 4-2: usbfs: interface 1 claimed by usblp while 'usb' sets config #1
[42376.672075] usb 4-2: USB disconnect, address 3
[42376.672494] usblp0: removed
harris@harris-desktop:~$


[Aristotelis]

φιλε μου 'harriscarouzos'

επειδή σκέφτομαι να την χτυπήσω την καρτούλα δουλεύει αναλογικά και ψηφιακά όλα ok

thanks