lucid beta Δεν τερματίζει.

[emmsarris]

Το'χω ήδη γράψει στο post όπου αναφέρονται τα νέα για το lucid (κακώς βέβαια, αλλά έχω κάνει οπότε...), αλλά είπα να ανοίξω νέο post μιας και δε βλέπω κάποιο update να το διορθώνει.
Στο laptop λοιπόν της υπογραφής μου, το lucid δεν τερματίζει, αντίθετα κάνει επανεκκίνηση. Το πρόβλημα εμφανίστηκε από την alpha2 έκδοση, που είχα κάνει δοκιμαστική εγκατάσταση μέχρι την beta1, οπότε την έβγαλα. Τώρα παρακολουθώ την πορεία από τα daily builds (όποτε προλαβαίνω). Σήμερα λοιπόν κατέβασα το daily build, και συνεχίζει. Έχω κάνει κάποια bug report στο launchpad αλλά δεν είμαι και σίγουρος αν έχουν καταλάβει τι ακριβώς λέω, οπότε είπα με τη βοήθεια της κοινότητας να κάνω ένα σωστό bug report ώστε να διορθωθεί το τυχόν πρόβλημα.
Να σημειώσω ότι το ίδιο συμβαίνει στο ubuntu32, στο ubuntu64, στο kubuntu32, στο kubuntu64, στο xubuntu32 και στο lubuntu32, είτε σε γραφικό είτε σε τερματικό. Τα ίδια CD (τα 32bitα, ε!) δουλεύουν θαυμάσια και τερματίζουν κανονικά στο desktop της υπογραφής μου και σε ένα laptop dell φίλου (δεν είδα τα χαρακτηριστικά του). Στο Karmic και το Jaunty δεν έχει κανένα πρόβλημα.
Εγώ βέβαια (χωρίς να έχω ιδέα) ψιλιάζομαι είτε το plymouth, είτε το ureadahead, είτε τον πυρήνα, που είναι και αυτό που φοβάμαι περισσότερο, αλλά δεν έχει βγεί άλλη διανομή με τον 2.6.32 για να το διαπιστώσω.
Δείτε και ένα screenshot από την εντολή sudo shutdown -P now:

Επίσης τα 2 σχετικά (?) bug report μου στο launchpad:
https://bugs.launchpad.net/ubuntu/+sour ... bug/506418
https://bugs.launchpad.net/ubuntu/lucid ... bug/537262
Αυτή τη στιγμή επειδή είμαι μεταξύ Ηρακλείου και Ρεθύμνου λόγω δουλειάς, δεν προλαβαίνω να το εγκαταστήσω και να παρακολουθώ την την πορεία του.
Όποιος έχει την καλωσύνη να ασχοληθεί τον ευχαριστώ προκαταβολικά.

[taratatzoum]

αν έχω καταλάβει καλά και αν εκτελείς σωστά τις εντολές

Κώδικας: Επιλογή όλων

sudo shutdown -h now

ή

Κώδικας: Επιλογή όλων

sudo shutdown -h 1 (θα σβήσει σε ένα λεπτό)

ή

Κώδικας: Επιλογή όλων

sudo shutdown -t

τότε για κάποιο λόγο δεν μπορεί να μπει σε init0 ώστε να κάνει halt και μπαίνει σε init6 όπου γίνεται το reboot
αλλά για να βεβαιωθούμε ακόμα πιο πολύ βάλε στον τερματικό

Κώδικας: Επιλογή όλων

/etc/rc.d/rc.0


και πάτα εντερ αν δεν κλείσει και έτσι πάμε για καρά bug
όταν δώσεις το bug να επισυνάψεις
το αρχείο /etc/inittab και το /etc/rc.d/rc.0 από το σύστημα σου.

[emmsarris]

Εκτός από το

Κώδικας: Επιλογή όλων

sudo shutdown -t

Που δεν το ήξερα, τους συνδυασμούς με -P, -H και -h τους έχω δοκιμάσει. Μάλιστα ο -h κολλάει το laptop δείχνοντας ως τελευταία "δράση" το shutting down. Μόλις το γράψει, δεν ανταποκρίνονται ούτε συνδυασμοί Alt+F2,3 κλπ, ούτε CTRL+ALT+DEL, ούτε γράφει τπτ.
Άλλη μία ερώτηση, το γραφικό περιβάλλον το εμφανίζει με ctrl+F8. Στο 7 δεν είναι σε όλα τα λειτουργικά? Εμένα στο 7 δείχνει μόνο το τελευταίο μνμ που εμφανίζει πριν ξεκινήσει ο x server.
Επίσης, πρέπει να είναι εγκατεστημένο για να δω αυτά τα αρχεία? Γιατί σε livecd δεν υπάρχουν...

[taratatzoum]

τα υπόλοιπα τα δοκίμασες ;

Κώδικας: Επιλογή όλων

/etc/rc.d/rc.0

[emmsarris]

Από livecd όπως διόρθωσα παραπάνω, δεν υπάρχουν αυτά τα αρχεία, οπότε δεν εκτελείται και η εντολή...
Υπάρχει rc0.d, rc1.d,...., rc6.d & rcS. inittab δεν υπάρχει
Εν πάση περιπτώσει εκτέλεσα από τερματικό

Κώδικας: Επιλογή όλων

sudo /etc/rc0.d/S90halt

(αν θυμάμαι σωστά) και πάλι έκανε επανεκκίνηση.

[taratatzoum]

δεν είμαι σε ubuntu και προφανώς κάποια script αλλάζουν η ουσία είναι οτι από live cd bug δεν μπορείς να δώσεις ουσιαστικό αν και τυπικά μπορείς.
παρόλα αυτά άμα θες δώσε όλο αυτό το ιστορικό τις ενέργειες που έκανες κτλ ...
απλά όταν στέλνεις bug report από το σύστημα αυτοί βλέπουν ότι είσαι σε live cd και δεν πολύ δίνουν σημασία. διότι σου λέει δεν έχεις κάνει όλα τα update-upgrade και ίσως να έχεις διορθωθεί σε κάποιο από αυτά το πρόβλημα...

[emmsarris]

Το πρώτο bug report έχει γίνει από εγκατάσταση. ΚΑΙ στην εγκατάσταση κάνει επανεκκίνηση. Μάλιστα αν δεις τα post μου viewtopic.php?f=14&t=8160&start=110#p109524 και μετά καμιά ενέργεια δεν εκτελούνταν σωστά. Αλλά λίγο πριν την beta 1 το έβγαλα και είναι δύσκολο να το ξαναδοκιμάσω (τουλάχιστο όχι πριν τις 22 του μήνα!)

[emmsarris]

Σήμερα εγκατέστησα την beta 2. Προφανώς το πρόβλημα συνεχίζει. Μπορεί κανένας να μου πει τι να κάνω, τι και που να ψάξω, και πως να στείλω bug report στο launchpad???

https://answers.launchpad.net/ubuntu/+question/107192

[emmsarris]

Και η εντολή

Κώδικας: Επιλογή όλων

sudo /etc/rc0.d/S90halt stop

επανεκκίνηση κάνει.
Καμιά ιδέα κανείς?????

[emmsarris]

dmesg

Κώδικας: Επιλογή όλων


[ 0.215163] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
[ 0.215166] pci 0000:00:06.0: PME# disabled
[ 0.216046] pci 0000:00:11.0: reg 10 io port: [0x8420-0x8427]
[ 0.216054] pci 0000:00:11.0: reg 14 io port: [0x8414-0x8417]
[ 0.216061] pci 0000:00:11.0: reg 18 io port: [0x8418-0x841f]
[ 0.216068] pci 0000:00:11.0: reg 1c io port: [0x8410-0x8413]
[ 0.216075] pci 0000:00:11.0: reg 20 io port: [0x8400-0x840f]
[ 0.216083] pci 0000:00:11.0: reg 24 32bit mmio: [0xf0408000-0xf04083ff]
[ 0.216137] pci 0000:00:12.0: reg 10 32bit mmio: [0xf0404000-0xf0404fff]
[ 0.216192] pci 0000:00:12.1: reg 10 32bit mmio: [0xf0405000-0xf0405fff]
[ 0.216266] pci 0000:00:12.2: reg 10 32bit mmio: [0xf0408400-0xf04084ff]
[ 0.216319] pci 0000:00:12.2: supports D1 D2
[ 0.216321] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[ 0.216326] pci 0000:00:12.2: PME# disabled
[ 0.216358] pci 0000:00:13.0: reg 10 32bit mmio: [0xf0406000-0xf0406fff]
[ 0.216414] pci 0000:00:13.1: reg 10 32bit mmio: [0xf0407000-0xf0407fff]
[ 0.216487] pci 0000:00:13.2: reg 10 32bit mmio: [0xf0408800-0xf04088ff]
[ 0.216540] pci 0000:00:13.2: supports D1 D2
[ 0.216542] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[ 0.216546] pci 0000:00:13.2: PME# disabled
[ 0.216673] pci 0000:00:14.2: reg 10 64bit mmio: [0xf0400000-0xf0403fff]
[ 0.216717] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[ 0.216721] pci 0000:00:14.2: PME# disabled
[ 0.216953] pci 0000:02:00.0: reg 10 32bit mmio pref: [0xd0000000-0xdfffffff]
[ 0.216958] pci 0000:02:00.0: reg 14 io port: [0x9000-0x90ff]
[ 0.216964] pci 0000:02:00.0: reg 18 32bit mmio: [0xcfef0000-0xcfefffff]
[ 0.216976] pci 0000:02:00.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[ 0.216992] pci 0000:02:00.0: supports D1 D2
[ 0.217016] pci 0000:02:00.1: reg 10 32bit mmio: [0xcfeec000-0xcfeeffff]
[ 0.217047] pci 0000:02:00.1: supports D1 D2
[ 0.217134] pci 0000:00:02.0: bridge io port: [0x9000-0x9fff]
[ 0.217137] pci 0000:00:02.0: bridge 32bit mmio: [0xcfe00000-0xcfefffff]
[ 0.217141] pci 0000:00:02.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
[ 0.217192] pci 0000:03:00.0: reg 10 64bit mmio: [0xf0200000-0xf020ffff]
[ 0.217252] pci 0000:03:00.0: PME# supported from D3hot D3cold
[ 0.217256] pci 0000:03:00.0: PME# disabled
[ 0.217348] pci 0000:00:04.0: bridge 32bit mmio: [0xf0200000-0xf02fffff]
[ 0.217389] pci 0000:09:00.0: reg 10 64bit mmio: [0xf0300000-0xf030ffff]
[ 0.217439] pci 0000:09:00.0: supports D1
[ 0.217441] pci 0000:09:00.0: PME# supported from D0 D1 D3hot
[ 0.217445] pci 0000:09:00.0: PME# disabled
[ 0.217540] pci 0000:00:06.0: bridge 32bit mmio: [0xf0300000-0xf03fffff]
[ 0.217600] pci 0000:00:14.4: transparent bridge
[ 0.217621] pci_bus 0000:00: on NUMA node 0
[ 0.217625] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.217825] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB2_._PRT]
[ 0.217908] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
[ 0.217984] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT]
[ 0.218094] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[ 0.222520] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
[ 0.222716] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
[ 0.222911] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
[ 0.223107] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
[ 0.223302] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
[ 0.223498] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
[ 0.223693] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
[ 0.223889] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
[ 0.224087] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.224091] vgaarb: loaded
[ 0.224194] SCSI subsystem initialized
[ 0.224278] libata version 3.00 loaded.
[ 0.224341] usbcore: registered new interface driver usbfs
[ 0.224356] usbcore: registered new interface driver hub
[ 0.224377] usbcore: registered new device driver usb
[ 0.224528] ACPI: WMI: Mapper loaded
[ 0.224530] PCI: Using ACPI for IRQ routing
[ 0.224711] NetLabel: Initializing
[ 0.224713] NetLabel: domain hash size = 128
[ 0.224714] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.224726] NetLabel: unlabeled traffic allowed by default
[ 0.224792] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 24, 0
[ 0.224798] hpet0: 4 comparators, 32-bit 14.318180 MHz counter
[ 0.226809] Switching to clocksource tsc
[ 0.226990] AppArmor: AppArmor Filesystem Enabled
[ 0.226990] pnp: PnP ACPI init
[ 0.226990] ACPI: bus type pnp registered
[ 0.230974] pnp: PnP ACPI: found 11 devices
[ 0.230977] ACPI: ACPI bus type pnp unregistered
[ 0.230981] PnPBIOS: Disabled by ACPI PNP
[ 0.230993] system 00:01: ioport range 0xf50-0xf51 has been reserved
[ 0.230998] system 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.231001] system 00:01: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.231009] system 00:06: ioport range 0x220-0x22f has been reserved
[ 0.231012] system 00:06: ioport range 0x40b-0x40b has been reserved
[ 0.231014] system 00:06: ioport range 0x4d0-0x4d1 has been reserved
[ 0.231017] system 00:06: ioport range 0x4d6-0x4d6 has been reserved
[ 0.231020] system 00:06: ioport range 0x530-0x537 has been reserved
[ 0.231022] system 00:06: ioport range 0xc00-0xc01 has been reserved
[ 0.231025] system 00:06: ioport range 0xc14-0xc14 has been reserved
[ 0.231027] system 00:06: ioport range 0xc50-0xc52 has been reserved
[ 0.231030] system 00:06: ioport range 0xc6c-0xc6c has been reserved
[ 0.231033] system 00:06: ioport range 0xc6f-0xc6f has been reserved
[ 0.231035] system 00:06: ioport range 0xcd0-0xcd1 has been reserved
[ 0.231038] system 00:06: ioport range 0xcd2-0xcd3 has been reserved
[ 0.231041] system 00:06: ioport range 0xcd4-0xcd5 has been reserved
[ 0.231043] system 00:06: ioport range 0xcd6-0xcd7 has been reserved
[ 0.231046] system 00:06: ioport range 0xcd8-0xcdf has been reserved
[ 0.231049] system 00:06: ioport range 0x8000-0x805f has been reserved
[ 0.231052] system 00:06: ioport range 0xf40-0xf47 has been reserved
[ 0.231054] system 00:06: ioport range 0x87f-0x87f has been reserved
[ 0.231057] system 00:06: iomem range 0xff800000-0xffefffff has been reserved
[ 0.231060] system 00:06: iomem range 0xfec10000-0xfec1001f has been reserved
[ 0.231066] system 00:07: iomem range 0xe0000-0xfffff could not be reserved
[ 0.231069] system 00:07: iomem range 0xffe00000-0xffffffff could not be reserved
[ 0.231072] system 00:07: iomem range 0xfec10000-0xfec1001f has been reserved
[ 0.266101] pci 0000:00:02.0: PCI bridge, secondary bus 0000:02
[ 0.266104] pci 0000:00:02.0: IO window: 0x9000-0x9fff
[ 0.266108] pci 0000:00:02.0: MEM window: 0xcfe00000-0xcfefffff
[ 0.266112] pci 0000:00:02.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
[ 0.266116] pci 0000:00:04.0: PCI bridge, secondary bus 0000:03
[ 0.266118] pci 0000:00:04.0: IO window: disabled
[ 0.266122] pci 0000:00:04.0: MEM window: 0xf0200000-0xf02fffff
[ 0.266124] pci 0000:00:04.0: PREFETCH window: disabled
[ 0.266128] pci 0000:00:06.0: PCI bridge, secondary bus 0000:09
[ 0.266130] pci 0000:00:06.0: IO window: disabled
[ 0.266134] pci 0000:00:06.0: MEM window: 0xf0300000-0xf03fffff
[ 0.266136] pci 0000:00:06.0: PREFETCH window: disabled
[ 0.266140] pci 0000:00:14.4: PCI bridge, secondary bus 0000:0a
[ 0.266142] pci 0000:00:14.4: IO window: disabled
[ 0.266181] pci 0000:00:14.4: MEM window: disabled
[ 0.266184] pci 0000:00:14.4: PREFETCH window: disabled
[ 0.266197] alloc irq_desc for 18 on node -1
[ 0.266199] alloc kstat_irqs on node -1
[ 0.266204] pci 0000:00:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.266208] pci 0000:00:02.0: setting latency timer to 64
[ 0.266213] alloc irq_desc for 16 on node -1
[ 0.266215] alloc kstat_irqs on node -1
[ 0.266218] pci 0000:00:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.266221] pci 0000:00:04.0: setting latency timer to 64
[ 0.266226] pci 0000:00:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.266229] pci 0000:00:06.0: setting latency timer to 64
[ 0.266238] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.266240] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.266243] pci_bus 0000:02: resource 0 io: [0x9000-0x9fff]
[ 0.266246] pci_bus 0000:02: resource 1 mem: [0xcfe00000-0xcfefffff]
[ 0.266248] pci_bus 0000:02: resource 2 pref mem [0xd0000000-0xdfffffff]
[ 0.266251] pci_bus 0000:03: resource 1 mem: [0xf0200000-0xf02fffff]
[ 0.266254] pci_bus 0000:09: resource 1 mem: [0xf0300000-0xf03fffff]
[ 0.266257] pci_bus 0000:0a: resource 3 io: [0x00-0xffff]
[ 0.266259] pci_bus 0000:0a: resource 4 mem: [0x000000-0xffffffff]
[ 0.266295] NET: Registered protocol family 2
[ 0.266383] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.266678] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.267222] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.267491] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.267493] TCP reno registered
[ 0.267576] NET: Registered protocol family 1
[ 0.267701] pci 0000:02:00.0: Boot video device
[ 0.267898] cpufreq-nforce2: No nForce2 chipset.
[ 0.267923] Scanning for low memory corruption every 60 seconds
[ 0.268019] audit: initializing netlink socket (disabled)
[ 0.268028] type=2000 audit(1271161285.265:1): initialized
[ 0.277087] highmem bounce pool size: 64 pages
[ 0.277092] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.278424] VFS: Disk quotas dquot_6.5.2
[ 0.278477] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.278982] fuse init (API version 7.13)
[ 0.279057] msgmni has been set to 1664
[ 0.279232] alg: No test for stdrng (krng)
[ 0.279280] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.279284] io scheduler noop registered
[ 0.279286] io scheduler anticipatory registered
[ 0.279287] io scheduler deadline registered
[ 0.279327] io scheduler cfq registered (default)
[ 0.279448] alloc irq_desc for 25 on node -1
[ 0.279450] alloc kstat_irqs on node -1
[ 0.279458] pcieport 0000:00:02.0: irq 25 for MSI/MSI-X
[ 0.279464] pcieport 0000:00:02.0: setting latency timer to 64
[ 0.279537] alloc irq_desc for 26 on node -1
[ 0.279539] alloc kstat_irqs on node -1
[ 0.279543] pcieport 0000:00:04.0: irq 26 for MSI/MSI-X
[ 0.279548] pcieport 0000:00:04.0: setting latency timer to 64
[ 0.279618] alloc irq_desc for 27 on node -1
[ 0.279620] alloc kstat_irqs on node -1
[ 0.279624] pcieport 0000:00:06.0: irq 27 for MSI/MSI-X
[ 0.279629] pcieport 0000:00:06.0: setting latency timer to 64
[ 0.279686] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.279708] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.280693] ACPI: AC Adapter [ADP1] (on-line)
[ 0.280764] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.280768] ACPI: Power Button [PWRB]
[ 0.280805] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[ 0.281768] ACPI: Lid Switch [LID0]
[ 0.281839] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[ 0.281879] ACPI: Sleep Button [SLPB]
[ 0.281936] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 0.281939] ACPI: Power Button [PWRF]
[ 0.282190] ACPI: processor limited to max C-state 1
[ 0.282211] processor LNXCPU:00: registered as cooling_device0
[ 0.282241] processor LNXCPU:01: registered as cooling_device1
[ 0.295896] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.295908] ACPI: Thermal Zone [TZS0] (51 C)
[ 0.302005] thermal LNXTHERM:02: registered as thermal_zone1
[ 0.302016] ACPI: Thermal Zone [TZS1] (47 C)
[ 0.303460] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.304587] brd: module loaded
[ 0.304979] loop: module loaded
[ 0.305061] input: Macintosh mouse button emulation as /devices/virtual/input/input4
[ 0.305446] Fixed MDIO Bus: probed
[ 0.305477] PPP generic driver version 2.4.2
[ 0.305511] tun: Universal TUN/TAP device driver, 1.6
[ 0.305513] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.305582] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.305637] alloc irq_desc for 17 on node -1
[ 0.305639] alloc kstat_irqs on node -1
[ 0.305646] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.305663] ehci_hcd 0000:00:12.2: EHCI Host Controller
[ 0.305696] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
[ 0.305727] ehci_hcd 0000:00:12.2: debug port 1
[ 0.305750] ehci_hcd 0000:00:12.2: irq 17, io mem 0xf0408400
[ 0.305892] isapnp: Scanning for PnP cards...
[ 0.360098] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 0.360173] usb usb1: configuration #1 chosen from 1 choice
[ 0.360199] hub 1-0:1.0: USB hub found
[ 0.360205] hub 1-0:1.0: 6 ports detected
[ 0.360295] alloc irq_desc for 19 on node -1
[ 0.360297] alloc kstat_irqs on node -1
[ 0.360301] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.360311] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 0.360339] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
[ 0.360365] ehci_hcd 0000:00:13.2: debug port 1
[ 0.360385] ehci_hcd 0000:00:13.2: irq 19, io mem 0xf0408800
[ 0.373345] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 0.373476] usb usb2: configuration #1 chosen from 1 choice
[ 0.373504] hub 2-0:1.0: USB hub found
[ 0.373513] hub 2-0:1.0: 6 ports detected
[ 0.373614] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.373668] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.373689] ohci_hcd 0000:00:12.0: OHCI Host Controller
[ 0.373741] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 3
[ 0.373773] ohci_hcd 0000:00:12.0: irq 16, io mem 0xf0404000
[ 0.380874] Freeing initrd memory: 7648k freed
[ 0.433188] usb usb3: configuration #1 chosen from 1 choice
[ 0.433217] hub 3-0:1.0: USB hub found
[ 0.433262] hub 3-0:1.0: 3 ports detected
[ 0.433319] ohci_hcd 0000:00:12.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.433336] ohci_hcd 0000:00:12.1: OHCI Host Controller
[ 0.433368] ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 4
[ 0.433433] ohci_hcd 0000:00:12.1: irq 16, io mem 0xf0405000
[ 0.473943] ACPI: Battery Slot [BAT0] (battery present)
[ 0.493198] usb usb4: configuration #1 chosen from 1 choice
[ 0.493229] hub 4-0:1.0: USB hub found
[ 0.493240] hub 4-0:1.0: 3 ports detected
[ 0.493294] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.493313] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 0.493346] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
[ 0.493417] ohci_hcd 0000:00:13.0: irq 18, io mem 0xf0406000
[ 0.557176] usb usb5: configuration #1 chosen from 1 choice
[ 0.557204] hub 5-0:1.0: USB hub found
[ 0.557249] hub 5-0:1.0: 3 ports detected
[ 0.557307] ohci_hcd 0000:00:13.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.557325] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 0.557360] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 6
[ 0.557421] ohci_hcd 0000:00:13.1: irq 18, io mem 0xf0407000
[ 0.617162] usb usb6: configuration #1 chosen from 1 choice
[ 0.617189] hub 6-0:1.0: USB hub found
[ 0.617234] hub 6-0:1.0: 3 ports detected
[ 0.617290] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.617365] PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.626781] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 0.633287] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.633293] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.633318] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.633337] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.633356] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.633454] mice: PS/2 mouse device common for all mice
[ 0.633722] rtc_cmos 00:04: RTC can wake from S4
[ 0.633757] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 0.633783] rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
[ 0.633876] device-mapper: uevent: version 1.0.3
[ 0.633964] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.634017] device-mapper: multipath: version 1.1.0 loaded
[ 0.634019] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.634113] EISA: Probing bus 0 at eisa.0
[ 0.634146] Cannot allocate resource for EISA slot 8
[ 0.634148] EISA: Detected 0 cards.
[ 0.634205] cpuidle: using governor ladder
[ 0.634207] cpuidle: using governor menu
[ 0.634615] TCP cubic registered
[ 0.634749] NET: Registered protocol family 10
[ 0.635170] lo: Disabled Privacy Extensions
[ 0.635475] NET: Registered protocol family 17
[ 0.635502] powernow-k8: Found 1 AMD Athlon(tm) II Dual-Core M300 processors (2 cpu cores) (version 2.20.00)
[ 0.635535] powernow-k8: 0 : pstate 0 (2000 MHz)
[ 0.635537] powernow-k8: 1 : pstate 1 (1400 MHz)
[ 0.635539] powernow-k8: 2 : pstate 2 (800 MHz)
[ 0.638193] Using IPI No-Shortcut mode
[ 0.638290] PM: Resume from disk failed.
[ 0.638301] registered taskstats version 1
[ 0.638731] Magic number: 6:59:380
[ 0.638869] rtc_cmos 00:04: setting system clock to 2010-04-13 12:21:26 UTC (1271161286)
[ 0.638872] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.638874] EDD information not available.
[ 0.655825] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 0.686840] isapnp: No Plug & Play device found
[ 0.686876] Freeing unused kernel memory: 656k freed
[ 0.687155] Write protecting the kernel text: 4676k
[ 0.687190] Write protecting the kernel read-only data: 1840k
[ 0.707706] udev: starting version 151
[ 0.709141] usb 2-5: new high speed USB device using ehci_hcd and address 2
[ 0.806178] ahci 0000:00:11.0: version 3.0
[ 0.806233] alloc irq_desc for 22 on node -1
[ 0.806235] alloc kstat_irqs on node -1
[ 0.806244] ahci 0000:00:11.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 0.806339] ahci 0000:00:11.0: AHCI 0001.0100 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
[ 0.806343] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc
[ 0.806813] tg3.c:v3.102 (September 1, 2009)
[ 0.806827] tg3 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.806834] tg3 0000:03:00.0: setting latency timer to 64
[ 0.823753] scsi0 : ahci
[ 0.913070] scsi1 : ahci
[ 0.914381] ata1: SATA max UDMA/133 abar m1024@0xf0408000 port 0xf0408100 irq 22
[ 0.914387] ata2: SATA max UDMA/133 abar m1024@0xf0408000 port 0xf0408180 irq 22
[ 0.919825] usb 2-5: configuration #1 chosen from 1 choice
[ 1.400116] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.400147] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.401947] ata1.00: ATA-8: ST9250315AS, 0001SDM1, max UDMA/133
[ 1.401952] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.403486] ata2.00: ATAPI: HL-DT-STDVDRAM GT30N, 1.01, max UDMA/100, ATAPI AN
[ 1.404212] ata1.00: configured for UDMA/133
[ 1.407547] ata2.00: configured for UDMA/100
[ 1.413532] eth0: Tigon3 [partno(BCM95784M) rev 5784100] (PCI Express) MAC address 00:26:2d:69:31:0e
[ 1.413536] eth0: attached PHY is 5784 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[ 1.413539] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 1.413541] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 1.420221] scsi 0:0:0:0: Direct-Access ATA ST9250315AS 0001 PQ: 0 ANSI: 5
[ 1.420401] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.420474] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 1.420512] sd 0:0:0:0: [sda] Write Protect is off
[ 1.420515] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.420534] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.420716] sda:
[ 1.426814] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GT30N 1.01 PQ: 0 ANSI: 5
[ 1.434982] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.434987] Uniform CD-ROM driver Revision: 3.20
[ 1.435121] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.435179] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 1.442067] sda1 sda2 sda3 < sda5 sda6 sda7 > sda4
[ 1.484736] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.400970] EXT4-fs (sda7): mounted filesystem with ordered data mode
[ 11.378991] udev: starting version 151
[ 11.385260] Adding 6000236k swap on /dev/sda6. Priority:-1 extents:1 across:6000236k
[ 11.566582] type=1505 audit(1271150497.426:2): operation="profile_load" pid=611 name="/sbin/dhclient3"
[ 11.566858] type=1505 audit(1271150497.426:3): operation="profile_load" pid=611 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 11.567011] type=1505 audit(1271150497.426:4): operation="profile_load" pid=611 name="/usr/lib/connman/scripts/dhclient-script"
[ 12.174302] lp: driver loaded but no devices found
[ 12.228436] acer-wmi: Acer Laptop ACPI-WMI Extras
[ 12.232845] acer-wmi: Brightness must be controlled by generic video driver
[ 12.233326] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0x8040, revision 0
[ 12.256957] Linux agpgart interface v0.103
[ 12.271432] acpi device:03: registered as cooling_device2
[ 12.271945] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:00/LNXVIDEO:00/input/input6
[ 12.272074] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 12.339654] cfg80211: Calling CRDA to update world regulatory domain
[ 12.341300] Linux video capture interface: v2.00
[ 12.375284] [drm] Initialized drm 1.1.0 20060810
[ 12.378189] cfg80211: World regulatory domain updated:
[ 12.378192] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.378196] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.378199] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.378202] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.378204] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.378206] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.418624] uvcvideo: Found UVC 1.00 device CNF7017 (04f2:b044)
[ 12.474223] input: CNF7017 as /devices/pci0000:00/0000:00:13.2/usb2/2-5/2-5:1.0/input/input7
[ 12.474278] usbcore: registered new interface driver uvcvideo
[ 12.474282] USB Video Class driver (v0.1.0)
[ 12.542033] type=1505 audit(1271150498.401:5): operation="profile_load" pid=835 name="/usr/share/gdm/guest-session/Xsession"
[ 12.543683] type=1505 audit(1271150498.401:6): operation="profile_replace" pid=836 name="/sbin/dhclient3"
[ 12.544060] type=1505 audit(1271150498.401:7): operation="profile_replace" pid=836 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 12.544228] type=1505 audit(1271150498.405:8): operation="profile_replace" pid=836 name="/usr/lib/connman/scripts/dhclient-script"
[ 12.547230] type=1505 audit(1271150498.405:9): operation="profile_load" pid=837 name="/usr/bin/evince"
[ 12.550784] type=1505 audit(1271150498.409:10): operation="profile_load" pid=837 name="/usr/bin/evince-previewer"
[ 12.552998] type=1505 audit(1271150498.413:11): operation="profile_load" pid=837 name="/usr/bin/evince-thumbnailer"
[ 12.701182] [drm] radeon kernel modesetting enabled.
[ 12.701556] radeon 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 12.701562] radeon 0000:02:00.0: setting latency timer to 64
[ 12.703475] [drm] radeon: Initializing kernel modesetting.
[ 12.705205] [drm] register mmio base: 0xCFEF0000
[ 12.705208] [drm] register mmio size: 65536
[ 12.705256] ATOM BIOS: BR33093.006
[ 12.705271] [drm] Clocks initialized !
[ 12.705449] [drm] Detected VRAM RAM=256M, BAR=256M
[ 12.705454] [drm] RAM width 64bits DDR
[ 12.705547] [TTM] Zone kernel: Available graphics memory: 430258 kiB.
[ 12.705550] [TTM] Zone highmem: Available graphics memory: 1547830 kiB.
[ 12.705568] [drm] radeon: 256M of VRAM memory ready
[ 12.705570] [drm] radeon: 512M of GTT memory ready.
[ 12.705611] alloc irq_desc for 28 on node -1
[ 12.705613] alloc kstat_irqs on node -1
[ 12.705624] radeon 0000:02:00.0: irq 28 for MSI/MSI-X
[ 12.705628] [drm] radeon: using MSI.
[ 12.705657] [drm] radeon: irq initialized.
[ 12.705660] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 12.705997] [drm] Loading RV710 Microcode
[ 12.706002] platform radeon_cp.0: firmware: requesting radeon/RV710_pfp.bin
[ 12.743521] alloc irq_desc for 29 on node -1
[ 12.743525] alloc kstat_irqs on node -1
[ 12.743537] tg3 0000:03:00.0: irq 29 for MSI/MSI-X
[ 12.848849] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.017329] platform radeon_cp.0: firmware: requesting radeon/RV710_me.bin
[ 13.105194] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04731/0xa44000
[ 13.105687] platform radeon_cp.0: firmware: requesting radeon/R700_rlc.bin
[ 13.154688] [drm] ring test succeeded in 1 usecs
[ 13.154801] [drm] radeon: ib pool ready.
[ 13.154871] [drm] ib test succeeded in 0 usecs
[ 13.156240] [drm] Radeon Display Connectors
[ 13.156244] [drm] Connector 0:
[ 13.156246] [drm] LVDS
[ 13.156249] [drm] DDC: 0x7f68 0x7f68 0x7f6c 0x7f6c 0x7f70 0x7f70 0x7f74 0x7f74
[ 13.156251] [drm] Encoders:
[ 13.156253] [drm] LCD1: INTERNAL_UNIPHY2
[ 13.156254] [drm] Connector 1:
[ 13.156255] [drm] VGA
[ 13.156258] [drm] DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c 0x7e4c
[ 13.156259] [drm] Encoders:
[ 13.156261] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 13.156262] [drm] Connector 2:
[ 13.156264] [drm] HDMI-A
[ 13.156265] [drm] HPD1
[ 13.156267] [drm] DDC: 0x7e50 0x7e50 0x7e54 0x7e54 0x7e58 0x7e58 0x7e5c 0x7e5c
[ 13.156269] [drm] Encoders:
[ 13.156270] [drm] DFP1: INTERNAL_UNIPHY
[ 13.166358] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input8
[ 13.288302] [drm] fb mappable at 0xD0141000
[ 13.288305] [drm] vram apper at 0xD0000000
[ 13.288307] [drm] size 4325376
[ 13.288308] [drm] fb depth is 24
[ 13.288310] [drm] pitch is 5632
[ 13.288401] fb0: radeondrmfb frame buffer device
[ 13.288403] registered panic notifier
[ 13.288408] [drm] Initialized radeon 2.0.0 20080528 for 0000:02:00.0 on minor 0
[ 13.444239] ath9k 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 13.444249] ath9k 0000:09:00.0: setting latency timer to 64
[ 13.868545] ath: EEPROM regdomain: 0x65
[ 13.868547] ath: EEPROM indicates we should expect a direct regpair map
[ 13.868551] ath: Country alpha2 being used: 00
[ 13.868553] ath: Regpair used: 0x65
[ 13.881006] vga16fb: initializing
[ 13.881010] vga16fb: mapped to 0xc00a0000
[ 13.881018] vga16fb: not registering due to another framebuffer present
[ 13.911068] phy0: Selected rate control algorithm 'ath9k_rate_control'
[ 13.911810] Registered led device: ath9k-phy0::radio
[ 13.911827] Registered led device: ath9k-phy0::assoc
[ 13.911845] Registered led device: ath9k-phy0::tx
[ 13.911862] Registered led device: ath9k-phy0::rx
[ 13.911873] phy0: Atheros AR9280 MAC/BB Rev:2 AR5133 RF Rev:d0: mem=0xf8400000, irq=18
[ 13.964255] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 14.144182] ppdev: user-space parallel port driver
[ 14.284105] HDA Intel 0000:00:14.2: power state changed by ACPI to D0
[ 14.284150] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 14.416395] hda_codec: ALC888: BIOS auto-probing.
[ 14.417856] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:14.2/input/input9
[ 14.430491] HDA Intel 0000:02:00.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 14.430521] HDA Intel 0000:02:00.1: setting latency timer to 64
[ 15.421483] Console: switching to colour frame buffer device 170x48
[ 17.781505] hda-intel: IRQ timing workaround is activated for card #1. Suggest a bigger bdl_pos_adj.
[ 30.662551] wlan0: deauthenticating from 00:1f:9f:c6:20:0c by local choice (reason=3)
[ 30.662588] wlan0: direct probe to AP 00:1f:9f:c6:20:0c (try 1)
[ 30.667401] wlan0: direct probe responded
[ 30.667407] wlan0: authenticate with AP 00:1f:9f:c6:20:0c (try 1)
[ 30.669366] wlan0: authenticated
[ 30.669398] wlan0: associate with AP 00:1f:9f:c6:20:0c (try 1)
[ 30.672235] wlan0: RX AssocResp from 00:1f:9f:c6:20:0c (capab=0x411 status=0 aid=1)
[ 30.672239] wlan0: associated
[ 30.672564] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 41.504080] wlan0: no IPv6 routers present
[ 78.854456] cfg80211: Found new beacon on frequency: 2472 MHz (Ch 13) on phy0
[ 260.304176] No probe response from AP 00:1f:9f:c6:20:0c after 500ms, disconnecting.
[ 260.304242] ------------[ cut here ]------------
[ 260.304258] WARNING: at /build/buildd/linux-2.6.32/kernel/softirq.c:143 local_bh_enable_ip+0x61/0x90()
[ 260.304264] Hardware name: Aspire 5542
[ 260.304269] Modules linked in: snd_hda_codec_atihdmi snd_hda_codec_realtek binfmt_misc snd_hda_intel snd_hda_codec ppdev snd_hwdep snd_seq_dummy snd_pcm_oss snd_mixer_oss fbcon tileblit snd_pcm snd_seq_oss font bitblit snd_seq_midi softcursor arc4 vga16fb snd_rawmidi vgastate snd_seq_midi_event joydev ath9k snd_seq snd_timer mac80211 snd_seq_device radeon ttm ath snd uvcvideo soundcore drm_kms_helper snd_page_alloc drm videodev cfg80211 psmouse agpgart video serio_raw v4l1_compat i2c_piix4 i2c_algo_bit acer_wmi output lp led_class parport tg3 ahci
[ 260.304364] Pid: 990, comm: phy0 Not tainted 2.6.32-20-generic #30-Ubuntu
[ 260.304370] Call Trace:
[ 260.304383] [<c014c3d2>] warn_slowpath_common+0x72/0xa0
[ 260.304392] [<c0153381>] ? local_bh_enable_ip+0x61/0x90
[ 260.304399] [<c0153381>] ? local_bh_enable_ip+0x61/0x90
[ 260.304407] [<c014c41a>] warn_slowpath_null+0x1a/0x20
[ 260.304414] [<c0153381>] local_bh_enable_ip+0x61/0x90
[ 260.304423] [<c058b806>] _spin_unlock_bh+0x16/0x20
[ 260.304449] [<f865f1bf>] ath_tx_node_cleanup+0x14f/0x170 [ath9k]
[ 260.304471] [<f8659eee>] ath9k_sta_notify+0x4e/0xb0 [ath9k]
[ 260.304492] [<f844b647>] __sta_info_unlink+0x127/0x1b0 [mac80211]
[ 260.304511] [<f8659ea0>] ? ath9k_sta_notify+0x0/0xb0 [ath9k]
[ 260.304530] [<f844b703>] sta_info_unlink+0x33/0x50 [mac80211]
[ 260.304553] [<f8452eca>] ieee80211_set_disassoc+0x17a/0x1d0 [mac80211]
[ 260.304574] [<f8454e27>] ieee80211_sta_work+0x427/0x460 [mac80211]
[ 260.304585] [<c013eff3>] ? finish_task_switch+0x43/0xc0
[ 260.304596] [<c016369e>] run_workqueue+0x8e/0x150
[ 260.304617] [<f8454a00>] ? ieee80211_sta_work+0x0/0x460 [mac80211]
[ 260.304625] [<c01637e4>] worker_thread+0x84/0xe0
[ 260.304634] [<c0167740>] ? autoremove_wake_function+0x0/0x50
[ 260.304643] [<c0163760>] ? worker_thread+0x0/0xe0
[ 260.304649] [<c01674b4>] kthread+0x74/0x80
[ 260.304656] [<c0167440>] ? kthread+0x0/0x80
[ 260.304665] [<c0104087>] kernel_thread_helper+0x7/0x10
[ 260.304670] ---[ end trace e1e1bdf63474b8f0 ]---
[ 261.487993] wlan0: direct probe to AP 00:1f:9f:c6:20:0c (try 1)
[ 261.684065] wlan0: direct probe to AP 00:1f:9f:c6:20:0c (try 2)
[ 261.885078] wlan0: direct probe to AP 00:1f:9f:c6:20:0c (try 3)
[ 262.084169] wlan0: direct probe to AP 00:1f:9f:c6:20:0c timed out
[ 272.536721] wlan0: direct probe to AP 00:1f:9f:c6:20:0c (try 1)
[ 272.540293] wlan0: direct probe responded
[ 272.540304] wlan0: authenticate with AP 00:1f:9f:c6:20:0c (try 1)
[ 272.542593] wlan0: authenticated
[ 272.542657] wlan0: associate with AP 00:1f:9f:c6:20:0c (try 1)
[ 272.545602] wlan0: RX AssocResp from 00:1f:9f:c6:20:0c (capab=0x411 status=0 aid=1)
[ 272.545611] wlan0: associated


uname -a
Linux *****-laptop 2.6.32-20-generic #30-Ubuntu SMP Mon Apr 12 15:19:41 UTC 2010 i686 GNU/Linux

cat /proc/version_signature
Ubuntu 2.6.32-20.30-generic 2.6.32.11+drm33.2


sudo lspci -vnvn

Κώδικας: Επιλογή όλων

Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at f0200000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [40] Vital Product Data <?>
Capabilities: [60] Vendor Specific Information <?>
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee0300c Data: 4199
Capabilities: [cc] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <64us
ClockPM+ Suprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [13c] Virtual Channel <?>
Capabilities: [160] Device Serial Number 0e-31-69-fe-ff-2d-26-00
Capabilities: [16c] Power Budgeting <?>
Kernel driver in use: tg3
Kernel modules: tg3

09:00.0 Network controller [0280]: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) [168c:002a] (rev 01)
Subsystem: Foxconn International, Inc. Device [105b:e01f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f0300000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [60] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM unknown, Latency L0 <512ns, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 128 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [90] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00000000
PBA: BAR=0 offset=00000000
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00
Kernel driver in use: ath9k
Kernel modules: ath9k

manos@manos-laptop:~$ sudo lspci -vnvn
00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS780 Host Bridge Alternate [1022:9601]
Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [c4] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=12 MastHost- DefDir- DUL-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn+ LSEn+ ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 3.00
Link Frequency 0: 1.6GHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [54] HyperTransport: UnitID Clumping
Capabilities: [40] HyperTransport: Retry Mode
Capabilities: [9c] HyperTransport: #1a
Capabilities: [f8] HyperTransport: #1c

00:02.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0) [1022:9603]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: cfe00000-cfefffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep+ BwNot+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt+
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 2, PowerLimit 75.000000; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0300c Data: 4161
Capabilities: [b0] Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100] Vendor Specific Information <?>
Capabilities: [110] Virtual Channel <?>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0) [1022:9604]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: f0200000-f02fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep+ BwNot+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 4, PowerLimit 25.000000; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0300c Data: 4169
Capabilities: [b0] Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100] Vendor Specific Information <?>
Capabilities: [110] Virtual Channel <?>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:06.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) [1022:9606]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
Memory behind bridge: f0300000-f03fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #3, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep+ BwNot+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 6, PowerLimit 25.000000; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0300c Data: 4171
Capabilities: [b0] Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100] Vendor Specific Information <?>
Capabilities: [110] Virtual Channel <?>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:11.0 SATA controller [0106]: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] [1002:4391] (prog-if 01)
Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 8420 [size=8]
Region 1: I/O ports at 8414 [size=4]
Region 2: I/O ports at 8418 [size=8]
Region 3: I/O ports at 8410 [size=4]
Region 4: I/O ports at 8400 [size=16]
Region 5: Memory at f0408000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] SATA HBA <?>
Kernel driver in use: ahci
Kernel modules: ahci

00:12.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10)
Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0404000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd

00:12.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10)
Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0405000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd

00:12.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20)
Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f0408400 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd

00:13.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10)
Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f0406000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd

00:13.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10)
Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f0407000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd

00:13.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20)
Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at f0408800 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd

00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 3c)
Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: piix4_smbus
Kernel modules: i2c-piix4

00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel HDA) [1002:4383]
Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at f0400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:14.3 ISA bridge [0601]: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d]
Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0

00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=64
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration [1022:1200]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn+ LSEn+ ExtCTL- 64b-
Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 3.00
Link Frequency: 1.6GHz
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-

00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map [1022:1201]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller [1022:1202]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control [1022:1203]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>

00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control [1022:1204]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

02:00.0 VGA compatible controller [0300]: ATI Technologies Inc M92 [Mobility Radeon HD 4500 Series] [1002:9553]
Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 28
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at cfef0000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at cfe00000 [disabled] [size=128K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee0200c Data: 4191
Capabilities: [100] Vendor Specific Information <?>
Kernel driver in use: radeon
Kernel modules: radeon

02:00.1 Audio device [0403]: ATI Technologies Inc RV710/730 [1002:aa38]
Subsystem: Acer Incorporated [ALI] Device [1025:0293]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at cfeec000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [100] Vendor Specific Information <?>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

03:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10)
Subsystem: Acer Incorporated [ALI] Device [1025:0207]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at f0200000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [40] Vital Product Data <?>
Capabilities: [60] Vendor Specific Information <?>
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee0300c Data: 4199
Capabilities: [cc] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <64us
ClockPM+ Suprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [13c] Virtual Channel <?>
Capabilities: [160] Device Serial Number 0e-31-69-fe-ff-2d-26-00
Capabilities: [16c] Power Budgeting <?>
Kernel driver in use: tg3
Kernel modules: tg3

09:00.0 Network controller [0280]: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) [168c:002a] (rev 01)
Subsystem: Foxconn International, Inc. Device [105b:e01f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f0300000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [60] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM unknown, Latency L0 <512ns, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 128 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [90] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00000000
PBA: BAR=0 offset=00000000
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00
Kernel driver in use: ath9k
Kernel modules: ath9k