Δημοσιεύτηκε: 08 Μάιος 2009, 13:05
logari81 έγραψε:δώσε μας το αποτελεσμα του
- Κώδικας: Επιλογή όλων
dmesg
- Κώδικας: Επιλογή όλων
[ 0.647266] pci 0000:00:1d.7: reg 10 32bit mmio: [0xe037f400-0xe037f7ff]
[ 0.647311] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.647317] pci 0000:00:1d.7: PME# disabled
[ 0.647399] HPET not enabled in BIOS. You might try hpet=force boot option
[ 0.647406] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
[ 0.647411] pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH4 GPIO
[ 0.647433] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
[ 0.647441] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
[ 0.647448] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
[ 0.647456] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
[ 0.647464] pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf]
[ 0.647472] pci 0000:00:1f.1: reg 24 32bit mmio: [0x000000-0x0003ff]
[ 0.647513] pci 0000:00:1f.5: reg 10 io port: [0xe000-0xe0ff]
[ 0.647521] pci 0000:00:1f.5: reg 14 io port: [0xe400-0xe43f]
[ 0.647529] pci 0000:00:1f.5: reg 18 32bit mmio: [0xe037fc00-0xe037fdff]
[ 0.647537] pci 0000:00:1f.5: reg 1c 32bit mmio: [0xe037f800-0xe037f8ff]
[ 0.647560] pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
[ 0.647565] pci 0000:00:1f.5: PME# disabled
[ 0.647596] pci 0000:00:1f.6: reg 10 io port: [0xe800-0xe8ff]
[ 0.647604] pci 0000:00:1f.6: reg 14 io port: [0xe480-0xe4ff]
[ 0.647635] pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold
[ 0.647640] pci 0000:00:1f.6: PME# disabled
[ 0.647681] pci 0000:01:02.0: reg 10 32bit mmio: [0xe00fd000-0xe00fdfff]
[ 0.647719] pci 0000:01:02.0: PME# supported from D0 D3hot D3cold
[ 0.647724] pci 0000:01:02.0: PME# disabled
[ 0.647756] pci 0000:01:03.0: reg 10 io port: [0xc800-0xc8ff]
[ 0.647764] pci 0000:01:03.0: reg 14 32bit mmio: [0xe00fec00-0xe00fecff]
[ 0.647796] pci 0000:01:03.0: supports D1 D2
[ 0.647799] pci 0000:01:03.0: PME# supported from D1 D2 D3hot D3cold
[ 0.647805] pci 0000:01:03.0: PME# disabled
[ 0.647835] pci 0000:01:04.0: reg 10 32bit mmio: [0x000000-0x000fff]
[ 0.647846] pci 0000:01:04.0: supports D1 D2
[ 0.647849] pci 0000:01:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.647854] pci 0000:01:04.0: PME# disabled
[ 0.647885] pci 0000:01:04.1: reg 10 32bit mmio: [0xe00ff000-0xe00ff7ff]
[ 0.647920] pci 0000:01:04.1: PME# supported from D0 D3hot D3cold
[ 0.647925] pci 0000:01:04.1: PME# disabled
[ 0.647956] pci 0000:01:04.2: reg 10 32bit mmio: [0xe00ff800-0xe00ff8ff]
[ 0.647991] pci 0000:01:04.2: supports D1 D2
[ 0.647994] pci 0000:01:04.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.648000] pci 0000:01:04.2: PME# disabled
[ 0.648033] pci 0000:01:04.3: reg 10 32bit mmio: [0xe00ffc00-0xe00ffcff]
[ 0.648069] pci 0000:01:04.3: supports D1 D2
[ 0.648072] pci 0000:01:04.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.648077] pci 0000:01:04.3: PME# disabled
[ 0.648118] pci 0000:00:1e.0: transparent bridge
[ 0.648123] pci 0000:00:1e.0: bridge io port: [0xc000-0xcfff]
[ 0.648129] pci 0000:00:1e.0: bridge 32bit mmio: [0xe0000000-0xe00fffff]
[ 0.648159] bus 00 -> node 0
[ 0.648168] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.648373] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.651079] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12)
[ 0.651287] ACPI: PCI Interrupt Link [LNKB] (IRQs *11)
[ 0.651485] ACPI: PCI Interrupt Link [LNKC] (IRQs *10)
[ 0.651684] ACPI: PCI Interrupt Link [LNKD] (IRQs *10)
[ 0.651881] ACPI: PCI Interrupt Link [LNKE] (IRQs 11) *0, disabled.
[ 0.652095] ACPI: PCI Interrupt Link [LNKF] (IRQs *11)
[ 0.652293] ACPI: PCI Interrupt Link [LNKG] (IRQs *11)
[ 0.652490] ACPI: PCI Interrupt Link [LNKH] (IRQs *10)
[ 0.652661] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 45, should be 3F [20080926]
[ 0.652692] ACPI: WMI: Mapper loaded
[ 0.652912] SCSI subsystem initialized
[ 0.652963] libata version 3.00 loaded.
[ 0.653024] usbcore: registered new interface driver usbfs
[ 0.653046] usbcore: registered new interface driver hub
[ 0.653080] usbcore: registered new device driver usb
[ 0.653231] PCI: Using ACPI for IRQ routing
[ 0.653343] Bluetooth: Core ver 2.13
[ 0.653343] NET: Registered protocol family 31
[ 0.653343] Bluetooth: HCI device and connection manager initialized
[ 0.653343] Bluetooth: HCI socket layer initialized
[ 0.653343] NET: Registered protocol family 8
[ 0.653343] NET: Registered protocol family 20
[ 0.653343] NetLabel: Initializing
[ 0.653343] NetLabel: domain hash size = 128
[ 0.653343] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.653343] NetLabel: unlabeled traffic allowed by default
[ 0.653343] AppArmor: AppArmor Filesystem Enabled
[ 0.653343] pnp: PnP ACPI init
[ 0.653343] ACPI: bus type pnp registered
[ 0.656795] pnp: PnP ACPI: found 10 devices
[ 0.656799] ACPI: ACPI bus type pnp unregistered
[ 0.656803] PnPBIOS: Disabled by ACPI PNP
[ 0.656820] system 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 0.656824] system 00:07: ioport range 0x400-0x47f has been reserved
[ 0.656828] system 00:07: ioport range 0x500-0x53f has been reserved
[ 0.656835] system 00:08: ioport range 0x6a0-0x6a0 has been reserved
[ 0.656839] system 00:08: ioport range 0x1100-0x113f has been reserved
[ 0.656843] system 00:08: ioport range 0x1254-0x1254 has been reserved
[ 0.656847] system 00:08: ioport range 0x12d4-0x12d4 has been reserved
[ 0.656851] system 00:08: ioport range 0x1300-0x1375 has been reserved
[ 0.656855] system 00:08: ioport range 0x1377-0x137f has been reserved
[ 0.656859] system 00:08: ioport range 0x1376-0x1376 has been reserved
[ 0.656864] system 00:08: iomem range 0xfff00000-0xffffffff has been reserved
[ 0.656868] system 00:08: iomem range 0xffb00000-0xffbfffff has been reserved
[ 0.656873] system 00:08: iomem range 0xfeff0000-0xfeffffff has been reserved
[ 0.656881] system 00:09: iomem range 0x0-0x9ffff could not be reserved
[ 0.656885] system 00:09: iomem range 0xc0000-0xdffff could not be reserved
[ 0.656889] system 00:09: iomem range 0xe0000-0xfffff could not be reserved
[ 0.656893] system 00:09: iomem range 0x100000-0x1f7fffff could not be reserved
[ 0.691657] pci 0000:01:04.0: CardBus bridge, secondary bus 0000:02
[ 0.691661] pci 0000:01:04.0: IO window: 0x00c000-0x00c0ff
[ 0.691666] pci 0000:01:04.0: IO window: 0x00c400-0x00c4ff
[ 0.691671] pci 0000:01:04.0: PREFETCH window: 0x20000000-0x23ffffff
[ 0.691677] pci 0000:01:04.0: MEM window: 0x28000000-0x2bffffff
[ 0.691683] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
[ 0.691687] pci 0000:00:1e.0: IO window: 0xc000-0xcfff
[ 0.691694] pci 0000:00:1e.0: MEM window: 0xe0000000-0xe00fffff
[ 0.691700] pci 0000:00:1e.0: PREFETCH window: 0x00000020000000-0x00000023ffffff
[ 0.691716] pci 0000:00:1e.0: setting latency timer to 64
[ 0.691978] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
[ 0.691982] PCI: setting IRQ 11 as level-triggered
[ 0.691988] pci 0000:01:04.0: PCI INT A -> Link[LNKE] -> GSI 11 (level, low) -> IRQ 11
[ 0.691994] pci 0000:01:04.0: setting latency timer to 64
[ 0.691999] bus: 00 index 0 io port: [0x00-0xffff]
[ 0.692002] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[ 0.692010] bus: 01 index 0 io port: [0xc000-0xcfff]
[ 0.692013] bus: 01 index 1 mmio: [0xe0000000-0xe00fffff]
[ 0.692016] bus: 01 index 2 mmio: [0x20000000-0x23ffffff]
[ 0.692020] bus: 01 index 3 io port: [0x00-0xffff]
[ 0.692023] bus: 01 index 4 mmio: [0x000000-0xffffffff]
[ 0.692026] bus: 02 index 0 io port: [0xc000-0xc0ff]
[ 0.692029] bus: 02 index 1 io port: [0xc400-0xc4ff]
[ 0.692033] bus: 02 index 2 mmio: [0x20000000-0x23ffffff]
[ 0.692036] bus: 02 index 3 mmio: [0x28000000-0x2bffffff]
[ 0.692047] NET: Registered protocol family 2
[ 0.692193] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.692486] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.692609] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.692730] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.692734] TCP reno registered
[ 0.692814] NET: Registered protocol family 1
[ 0.692993] checking if image is initramfs... it is
[ 1.192059] Switched to high resolution mode on CPU 0
[ 1.407194] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 1.637520] Freeing initrd memory: 7369k freed
[ 1.637635] cpufreq: No nForce2 chipset.
[ 1.637868] audit: initializing netlink socket (disabled)
[ 1.637920] type=2000 audit(1241765210.636:1): initialized
[ 1.649309] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.651199] VFS: Disk quotas dquot_6.5.1
[ 1.651278] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.652172] fuse init (API version 7.10)
[ 1.652293] msgmni has been set to 978
[ 1.652559] alg: No test for stdrng (krng)
[ 1.652577] io scheduler noop registered
[ 1.652580] io scheduler anticipatory registered
[ 1.652583] io scheduler deadline registered
[ 1.652604] io scheduler cfq registered (default)
[ 1.652629] pci 0000:00:02.0: Boot video device
[ 1.654677] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.654690] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.654872] ACPI: AC Adapter [ADP0] (on-line)
[ 1.655451] ACPI: Battery Slot [BAT0] (battery present)
[ 1.655543] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 1.655547] ACPI: Power Button (FF) [PWRF]
[ 1.655621] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 1.655624] ACPI: Power Button (CM) [PWRB]
[ 1.655687] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[ 1.655730] ACPI: Lid Switch [LID0]
[ 1.656098] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 1.656132] processor ACPI_CPU:00: registered as cooling_device0
[ 1.656137] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 1.657480] isapnp: Scanning for PnP cards...
[ 2.011131] isapnp: No Plug & Play device found
[ 2.012946] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 2.013714] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[ 2.013721] serial 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 2.013730] serial 0000:00:1f.6: PCI INT B disabled
[ 2.014648] brd: module loaded
[ 2.015080] loop: module loaded
[ 2.015185] Fixed MDIO Bus: probed
[ 2.015194] PPP generic driver version 2.4.2
[ 2.015278] input: Macintosh mouse button emulation as /devices/virtual/input/input3
[ 2.015316] Driver 'sd' needs updating - please use bus_type methods
[ 2.015329] Driver 'sr' needs updating - please use bus_type methods
[ 2.015431] ata_piix 0000:00:1f.1: version 2.12
[ 2.015440] ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
[ 2.015705] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[ 2.015709] PCI: setting IRQ 10 as level-triggered
[ 2.015714] ata_piix 0000:00:1f.1: PCI INT A -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
[ 2.015767] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 2.015873] scsi0 : ata_piix
[ 2.015984] scsi1 : ata_piix
[ 2.018300] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 2.018304] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 2.180544] ata1.00: ATA-6: HTS541040G9AT00, MB2OA60A, max UDMA/100
[ 2.180548] ata1.00: 78140160 sectors, multi 16: LBA48
[ 2.196667] ata1.00: configured for UDMA/100
[ 2.360501] ata2.00: ATAPI: MATSHITAUJ-840D, 1.00, max UDMA/33
[ 2.376395] ata2.00: configured for UDMA/33
[ 2.376908] scsi 0:0:0:0: Direct-Access ATA HTS541040G9AT00 MB2O PQ: 0 ANSI: 5
[ 2.377040] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors: (40.0 GB/37.2 GiB)
[ 2.377065] sd 0:0:0:0: [sda] Write Protect is off
[ 2.377069] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.377106] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.377191] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors: (40.0 GB/37.2 GiB)
[ 2.377211] sd 0:0:0:0: [sda] Write Protect is off
[ 2.377215] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.377248] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.377254] sda: sda1 sda2 < sda5 >
[ 2.444211] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.444275] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.446133] scsi 1:0:0:0: CD-ROM MATSHITA UJ-840D 1.00 PQ: 0 ANSI: 5
[ 2.450582] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 2.450587] Uniform CD-ROM driver Revision: 3.20
[ 2.450700] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.450754] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 2.451598] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.451890] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
[ 2.451896] ehci_hcd 0000:00:1d.7: PCI INT D -> Link[LNKH] -> GSI 10 (level, low) -> IRQ 10
[ 2.451926] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 2.451931] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.452038] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 2.455964] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.455971] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 2.455982] ehci_hcd 0000:00:1d.7: irq 10, io mem 0xe037f400
[ 2.468011] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 2.468126] usb usb1: configuration #1 chosen from 1 choice
[ 2.468166] hub 1-0:1.0: USB hub found
[ 2.468178] hub 1-0:1.0: 6 ports detected
[ 2.468325] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.468349] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.468631] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
[ 2.468636] uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10
[ 2.468644] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.468649] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.468705] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 2.468728] uhci_hcd 0000:00:1d.0: irq 10, io base 0x0000d800
[ 2.468828] usb usb2: configuration #1 chosen from 1 choice
[ 2.468863] hub 2-0:1.0: USB hub found
[ 2.468874] hub 2-0:1.0: 2 ports detected
[ 2.469239] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
[ 2.469244] uhci_hcd 0000:00:1d.1: PCI INT B -> Link[LNKD] -> GSI 10 (level, low) -> IRQ 10
[ 2.469252] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2.469256] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.469317] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 2.469339] uhci_hcd 0000:00:1d.1: irq 10, io base 0x0000d880
[ 2.469439] usb usb3: configuration #1 chosen from 1 choice
[ 2.469473] hub 3-0:1.0: USB hub found
[ 2.469482] hub 3-0:1.0: 2 ports detected
[ 2.469581] uhci_hcd 0000:00:1d.2: PCI INT C -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
[ 2.469589] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 2.469593] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.469652] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 2.469673] uhci_hcd 0000:00:1d.2: irq 10, io base 0x0000dc00
[ 2.469767] usb usb4: configuration #1 chosen from 1 choice
[ 2.469800] hub 4-0:1.0: USB hub found
[ 2.469810] hub 4-0:1.0: 2 ports detected
[ 2.469965] usbcore: registered new interface driver libusual
[ 2.470008] usbcore: registered new interface driver usbserial
[ 2.470023] USB Serial support registered for generic
[ 2.470043] usbcore: registered new interface driver usbserial_generic
[ 2.470046] usbserial: USB Serial Driver core
[ 2.470111] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.471023] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 2.471273] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.471281] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 2.471285] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 2.471288] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 2.471292] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 2.471505] mice: PS/2 mouse device common for all mice
[ 2.471700] rtc_cmos 00:02: RTC can wake from S4
[ 2.471743] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 2.471763] rtc0: alarms up to one month, 114 bytes nvram
[ 2.471850] device-mapper: uevent: version 1.0.3
[ 2.471996] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 2.472067] device-mapper: multipath: version 1.0.5 loaded
[ 2.472071] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 2.472179] EISA: Probing bus 0 at eisa.0
[ 2.472220] EISA: Detected 0 cards.
[ 2.472313] cpuidle: using governor ladder
[ 2.472407] cpuidle: using governor menu
[ 2.473098] TCP cubic registered
[ 2.473242] NET: Registered protocol family 10
[ 2.473779] lo: Disabled Privacy Extensions
[ 2.474201] NET: Registered protocol family 17
[ 2.474224] Bluetooth: L2CAP ver 2.11
[ 2.474227] Bluetooth: L2CAP socket layer initialized
[ 2.474230] Bluetooth: SCO (Voice Link) ver 0.6
[ 2.474233] Bluetooth: SCO socket layer initialized
[ 2.474272] Bluetooth: RFCOMM socket layer initialized
[ 2.474283] Bluetooth: RFCOMM TTY layer initialized
[ 2.474285] Bluetooth: RFCOMM ver 1.10
[ 2.474596] IO APIC resources could be not be allocated.
[ 2.474646] Using IPI No-Shortcut mode
[ 2.474760] registered taskstats version 1
[ 2.474916] Magic number: 9:463:771
[ 2.475001] rtc_cmos 00:02: setting system clock to 2009-05-08 06:46:52 UTC (1241765212)
[ 2.475006] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.475008] EDD information not available.
[ 2.475404] Freeing unused kernel memory: 532k freed
[ 2.475565] Write protecting the kernel text: 4128k
[ 2.475621] Write protecting the kernel read-only data: 1532k
[ 2.478947] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 2.784037] usb 1-2: new high speed USB device using ehci_hcd and address 2
[ 2.916717] usb 1-2: configuration #1 chosen from 1 choice
[ 3.166978] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 3.167030] 8139cp 0000:01:03.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 3.171156] 8139too Fast Ethernet driver 0.9.28
[ 3.171524] ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
[ 3.171530] 8139too 0000:01:03.0: PCI INT A -> Link[LNKG] -> GSI 11 (level, low) -> IRQ 11
[ 3.172683] eth0: RealTek RTL8139 at 0xc800, 00:14:2a:3d:d8:1c, IRQ 11
[ 3.172687] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 3.201471] ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
[ 3.201480] ohci1394 0000:01:04.1: PCI INT B -> Link[LNKF] -> GSI 11 (level, low) -> IRQ 11
[ 3.254258] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[e00ff000-e00ff7ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 3.600312] Marking TSC unstable due to TSC halts in idle
[ 3.651313] PM: Starting manual resume from disk
[ 3.651318] PM: Resume from partition 8:5
[ 3.651321] PM: Checking hibernation image.
[ 3.651515] PM: Resume from disk failed.
[ 3.703788] kjournald starting. Commit interval 5 seconds
[ 3.703802] EXT3-fs: mounted filesystem with ordered data mode.
[ 4.536189] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00000ae6ff326d6c]
[ 10.841419] udev: starting version 141
[ 11.434943] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 11.440666] intel_rng: FWH not detected
[ 11.480791] Linux agpgart interface v0.103
[ 11.564377] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 11.685349] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:17/input/input6
[ 11.703857] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 11.713173] agpgart-intel 0000:00:00.0: Intel 855GM Chipset
[ 11.714109] agpgart-intel 0000:00:00.0: detected 8060K stolen memory
[ 11.716771] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xd8000000
[ 11.729394] ieee80211_crypt: registered algorithm 'NULL'
[ 11.743558] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 11.743562] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 11.766707] Linux video capture interface: v2.00
[ 11.766919] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[ 11.849570] sdhci: Secure Digital Host Controller Interface driver
[ 11.849574] sdhci: Copyright(c) Pierre Ossman
[ 11.852108] sdhci-pci 0000:01:04.2: SDHCI controller found [1180:0822] (rev 17)
[ 11.852132] sdhci-pci 0000:01:04.2: PCI INT C -> Link[LNKD] -> GSI 10 (level, low) -> IRQ 10
[ 11.855244] mmc0: SDHCI controller on PCI [0000:01:04.2] using PIO
[ 11.869146] iTCO_vendor_support: vendor-support=0
[ 11.909540] em28xx v4l2 driver version 0.1.0 loaded
[ 11.911604] em28xx new video device (eb1a:2750): interface 0, class 255
[ 11.911614] em28xx Doesn't have usb audio class
[ 11.911616] em28xx #0: Alternate settings: 8
[ 11.911619] em28xx #0: Alternate setting 0, max size= 0
[ 11.911622] em28xx #0: Alternate setting 1, max size= 0
[ 11.911626] em28xx #0: Alternate setting 2, max size= 1448
[ 11.911629] em28xx #0: Alternate setting 3, max size= 2048
[ 11.911632] em28xx #0: Alternate setting 4, max size= 2304
[ 11.911635] em28xx #0: Alternate setting 5, max size= 2580
[ 11.911638] em28xx #0: Alternate setting 6, max size= 2892
[ 11.911642] em28xx #0: Alternate setting 7, max size= 3072
[ 11.914167] em28xx #0: em28xx chip ID = 33
[ 11.918429] yenta_cardbus 0000:01:04.0: CardBus bridge found [1019:0f50]
[ 11.920952] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 11.921109] iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x0460)
[ 11.921226] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 11.943995] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[ 11.944011] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 12.058021] yenta_cardbus 0000:01:04.0: ISA IRQ mask 0x00b8, PCI irq 11
[ 12.058028] yenta_cardbus 0000:01:04.0: Socket status: 30000006
[ 12.058034] pci_bus 0000:01: Raising subordinate bus# of parent bus (#01) from #01 to #05
[ 12.058047] yenta_cardbus 0000:01:04.0: pcmcia: parent PCI bridge I/O window: 0xc000 - 0xcfff
[ 12.058052] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc000-0xcfff: clean.
[ 12.058343] yenta_cardbus 0000:01:04.0: pcmcia: parent PCI bridge Memory window: 0xe0000000 - 0xe00fffff
[ 12.058348] yenta_cardbus 0000:01:04.0: pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x23ffffff
[ 12.062496] ipw2200 0000:01:02.0: PCI INT A -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 12.074794] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 12.074857] ipw2200 0000:01:02.0: firmware: requesting ipw2200-bss.fw
[ 12.219490] em28xx #0: board has no eeprom
[ 12.292384] ipw2200: Radio Frequency Kill Switch is On:
[ 12.292387] Kill switch must be turned off for wireless networking to work.
[ 12.293858] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
[ 12.307271] Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 12.307380] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 12.414027] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[ 12.415760] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
[ 12.416206] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 12.416823] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 12.417643] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 12.604409] tvp5150 0-005d: *** unknown tvp0000 chip detected.
[ 12.604413] tvp5150 0-005d: *** Rom ver is 87.88
[ 12.625969] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x926eb1, caps: 0x804719/0x0
[ 12.658906] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input7
[ 13.132045] intel8x0_measure_ac97_clock: measured 55320 usecs
[ 13.132050] intel8x0: clocking to 48000
[ 15.248470] em28xx #0: V4L2 device registered as /dev/video0 and /dev/vbi0
[ 15.248476] em28xx #0: Found Unknown EM2750/EM2751 webcam grabber
[ 15.248510] usbcore: registered new interface driver em28xx
[ 15.274974] em28xx-audio.c: probing for em28x1 non standard usbaudio
[ 15.274980] em28xx-audio.c: Copyright (C) 2006 Markus Rechberger
[ 15.275401] Em28xx: Initialized (Em28xx Audio Extension) extension
[ 15.415877] lp: driver loaded but no devices found
[ 15.517887] Adding 1469908k swap on /dev/sda5. Priority:-1 extents:1 across:1469908k
[ 16.073648] EXT3 FS on sda1, internal journal
[ 16.188015] Clocksource tsc unstable (delta = -70095043 ns)
[ 17.290396] type=1505 audit(1241765227.313:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=1981
[ 17.365334] type=1505 audit(1241765227.389:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=1985
[ 17.365513] type=1505 audit(1241765227.389:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=1985
[ 17.365583] type=1505 audit(1241765227.389:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=1985
[ 17.365645] type=1505 audit(1241765227.389:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=1985
[ 17.586810] type=1505 audit(1241765227.609:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=1990
[ 17.587220] type=1505 audit(1241765227.609:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=1990
[ 17.629547] type=1505 audit(1241765227.653:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=1994
[ 20.671079] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 20.671084] Bluetooth: BNEP filters: protocol multicast
[ 20.716514] Bridge firewalling registered
[ 22.960027] ppdev: user-space parallel port driver
[ 23.591444] [drm] Initialized drm 1.1.0 20060810
[ 23.618634] pci 0000:00:02.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10
[ 23.618643] pci 0000:00:02.0: setting latency timer to 64
[ 23.618880] [drm] Initialized i915 1.6.0 20080730 on minor 0
[ 23.627374] [drm:i915_setparam] *ERROR* unknown parameter 4
[ 23.627409] [drm:i915_getparam] *ERROR* Unknown parameter 6
[ 25.098937] [drm:i915_getparam] *ERROR* Unknown parameter 6
[ 26.976244] eth0: link down
[ 26.976281] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 26.977086] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 34.036005] [drm:i915_getparam] *ERROR* Unknown parameter 6
[ 124.616748] ieee80211_crypt: registered algorithm 'WEP'
[ 124.693061] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 135.252386] eth1: no IPv6 routers present
[ 1622.168406] [drm:i915_getparam] *ERROR* Unknown parameter 6
[ 2763.308452] tvp5150 0-005d: *** unknown tvpdede chip detected.
[ 2763.308465] tvp5150 0-005d: *** Rom ver is 222.222
[ 2765.828404] tvp5150 0-005d: *** unknown tvpdede chip detected.
[ 2765.828416] tvp5150 0-005d: *** Rom ver is 222.222
[ 2768.396477] tvp5150 0-005d: *** unknown tvpdede chip detected.
[ 2768.396489] tvp5150 0-005d: *** Rom ver is 222.222
[ 2770.916433] tvp5150 0-005d: *** unknown tvpdede chip detected.
[ 2770.916445] tvp5150 0-005d: *** Rom ver is 222.222
[ 2773.460509] tvp5150 0-005d: *** unknown tvpdede chip detected.
[ 2773.460521] tvp5150 0-005d: *** Rom ver is 222.222
[ 2775.980463] tvp5150 0-005d: *** unknown tvpdede chip detected.
[ 2775.980475] tvp5150 0-005d: *** Rom ver is 222.222
[ 2778.504543] tvp5150 0-005d: *** unknown tvpdede chip detected.
[ 2778.504555] tvp5150 0-005d: *** Rom ver is 222.222
[ 2781.032497] tvp5150 0-005d: *** unknown tvpdede chip detected.
[ 2781.032509] tvp5150 0-005d: *** Rom ver is 222.222
[ 2783.552452] tvp5150 0-005d: *** unknown tvpdede chip detected.
[ 2783.552464] tvp5150 0-005d: *** Rom ver is 222.222
[ 3820.012101] [drm:i915_getparam] *ERROR* Unknown parameter 6
[ 5580.979075] [drm:i915_getparam] *ERROR* Unknown parameter 6
[ 5955.964469] tvp5150 0-005d: *** unknown tvpdede chip detected.
[ 5955.964483] tvp5150 0-005d: *** Rom ver is 222.222
[ 5958.636524] tvp5150 0-005d: *** unknown tvpdede chip detected.
[ 5958.636537] tvp5150 0-005d: *** Rom ver is 222.222
[ 6723.280904] [drm:i915_getparam] *ERROR* Unknown parameter 6
[ 9833.256012] [drm:i915_getparam] *ERROR* Unknown parameter 6