Δημοσιεύτηκε: 30 Ιαν 2012, 23:25
έβαλα τελικά και της αναβαθμίσεις και για το ifconfig
και dmesg
αυτά ευχαριστώ πάντως .
- Κώδικας: Επιλογή όλων
[eth0 Link encap:Ethernet HWaddr 50:e5:49:b9:2d:fd
inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::52e5:49ff:feb9:2dfd/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:366 errors:0 dropped:366 overruns:0 frame:366
TX packets:496 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:226210 (226.2 KB) TX bytes:65837 (65.8 KB)
Interrupt:40
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)]
και dmesg
- Κώδικας: Επιλογή όλων
[[ 0.860659] pci_bus 0000:06: resource 1 [mem 0xfd700000-0xfd7fffff]
[ 0.860661] pci_bus 0000:06: resource 2 [mem 0xfd600000-0xfd6fffff 64bit pref]
[ 0.860688] NET: Registered protocol family 2
[ 0.860738] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.860904] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.861126] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.861233] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.861235] TCP reno registered
[ 0.861238] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.861243] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.861311] NET: Registered protocol family 1
[ 0.940124] pci 0000:01:00.0: Boot video device
[ 0.940193] PCI: CLS 64 bytes, default 64
[ 0.941312] audit: initializing netlink socket (disabled)
[ 0.941326] type=2000 audit(1327954362.936:1): initialized
[ 0.970379] highmem bounce pool size: 64 pages
[ 0.970383] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.990873] VFS: Disk quotas dquot_6.5.2
[ 0.990937] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.991586] fuse init (API version 7.16)
[ 0.991668] msgmni has been set to 1551
[ 0.992117] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.992151] io scheduler noop registered
[ 0.992153] io scheduler deadline registered
[ 0.992168] io scheduler cfq registered (default)
[ 0.992413] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.992434] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.992547] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[ 0.992552] ACPI: Power Button [PWRB]
[ 0.992596] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.992599] ACPI: Power Button [PWRF]
[ 0.992625] ACPI: acpi_idle registered with cpuidle
[ 1.169559] ERST: Table is not found!
[ 1.169612] isapnp: Scanning for PnP cards...
[ 1.169743] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 1.190205] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.523012] isapnp: No Plug & Play device found
[ 1.552847] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.553055] Linux agpgart interface v0.103
[ 1.554216] brd: module loaded
[ 1.554674] loop: module loaded
[ 1.554821] pata_acpi 0000:00:14.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.555104] Fixed MDIO Bus: probed
[ 1.555123] PPP generic driver version 2.4.2
[ 1.555148] tun: Universal TUN/TAP device driver, 1.6
[ 1.555150] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.555213] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.555223] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.555231] ehci_hcd 0000:00:12.2: EHCI Host Controller
[ 1.555256] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
[ 1.555262] ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.555281] QUIRK: Enable AMD PLL fix
[ 1.555290] ehci_hcd 0000:00:12.2: debug port 1
[ 1.555307] ehci_hcd 0000:00:12.2: irq 17, io mem 0xfdffd000
[ 1.564056] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 1.564266] hub 1-0:1.0: USB hub found
[ 1.564274] hub 1-0:1.0: 5 ports detected
[ 1.564397] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.564415] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 1.564477] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
[ 1.564487] ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.564514] ehci_hcd 0000:00:13.2: debug port 1
[ 1.564530] ehci_hcd 0000:00:13.2: irq 17, io mem 0xfdffb000
[ 1.576051] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 1.576257] hub 2-0:1.0: USB hub found
[ 1.576264] hub 2-0:1.0: 5 ports detected
[ 1.576385] ehci_hcd 0000:00:16.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.576403] ehci_hcd 0000:00:16.2: EHCI Host Controller
[ 1.576464] ehci_hcd 0000:00:16.2: new USB bus registered, assigned bus number 3
[ 1.576473] ehci_hcd 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.576501] ehci_hcd 0000:00:16.2: debug port 1
[ 1.576517] ehci_hcd 0000:00:16.2: irq 17, io mem 0xfdff8000
[ 1.588054] ehci_hcd 0000:00:16.2: USB 2.0 started, EHCI 1.00
[ 1.588244] hub 3-0:1.0: USB hub found
[ 1.588251] hub 3-0:1.0: 4 ports detected
[ 1.588378] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.588399] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.588416] ohci_hcd 0000:00:12.0: OHCI Host Controller
[ 1.588476] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 4
[ 1.588513] ohci_hcd 0000:00:12.0: irq 18, io mem 0xfdffe000
[ 1.648214] hub 4-0:1.0: USB hub found
[ 1.648223] hub 4-0:1.0: 5 ports detected
[ 1.648343] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.648364] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 1.648432] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
[ 1.648454] ohci_hcd 0000:00:13.0: irq 18, io mem 0xfdffc000
[ 1.708223] hub 5-0:1.0: USB hub found
[ 1.708233] hub 5-0:1.0: 5 ports detected
[ 1.708356] ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.708374] ohci_hcd 0000:00:14.5: OHCI Host Controller
[ 1.708440] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 6
[ 1.708463] ohci_hcd 0000:00:14.5: irq 18, io mem 0xfdffa000
[ 1.768219] hub 6-0:1.0: USB hub found
[ 1.768228] hub 6-0:1.0: 2 ports detected
[ 1.768348] ohci_hcd 0000:00:16.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.768366] ohci_hcd 0000:00:16.0: OHCI Host Controller
[ 1.768434] ohci_hcd 0000:00:16.0: new USB bus registered, assigned bus number 7
[ 1.768457] ohci_hcd 0000:00:16.0: irq 18, io mem 0xfdff9000
[ 1.828219] hub 7-0:1.0: USB hub found
[ 1.828229] hub 7-0:1.0: 4 ports detected
[ 1.828356] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.828486] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 1.862579] i8042: Failed to disable AUX port, but continuing anyway... Is this a SiS?
[ 1.862583] i8042: If AUX port is really absent please use the 'i8042.noaux' option
[ 1.940046] Refined TSC clocksource calibration: 3322.207 MHz.
[ 1.940054] Switching to clocksource tsc
[ 2.044048] usb 5-5: new low speed USB device number 2 using ohci_hcd
[ 2.112117] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.112288] mousedev: PS/2 mouse device common for all mice
[ 2.112485] rtc_cmos 00:05: RTC can wake from S4
[ 2.112600] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 2.112625] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 2.112780] device-mapper: uevent: version 1.0.3
[ 2.112932] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[ 2.112990] EISA: Probing bus 0 at eisa.0
[ 2.112994] EISA: Cannot allocate resource for mainboard
[ 2.112998] Cannot allocate resource for EISA slot 1
[ 2.113002] Cannot allocate resource for EISA slot 2
[ 2.113005] Cannot allocate resource for EISA slot 3
[ 2.113008] Cannot allocate resource for EISA slot 4
[ 2.113011] Cannot allocate resource for EISA slot 5
[ 2.113014] Cannot allocate resource for EISA slot 6
[ 2.113017] Cannot allocate resource for EISA slot 7
[ 2.113020] Cannot allocate resource for EISA slot 8
[ 2.113023] EISA: Detected 0 cards.
[ 2.113038] cpufreq-nforce2: No nForce2 chipset.
[ 2.113258] cpuidle: using governor ladder
[ 2.113642] cpuidle: using governor menu
[ 2.113646] EFI Variables Facility v0.08 2004-May-17
[ 2.114159] TCP cubic registered
[ 2.114428] NET: Registered protocol family 10
[ 2.115498] NET: Registered protocol family 17
[ 2.115521] Registering the dns_resolver key type
[ 2.115544] Using IPI No-Shortcut mode
[ 2.115674] PM: Hibernation image not present or could not be loaded.
[ 2.115692] registered taskstats version 1
[ 2.144728] Magic number: 12:513:246
[ 2.144890] rtc_cmos 00:05: setting system clock to 2012-01-30 20:12:45 UTC (1327954365)
[ 2.144935] powernow-k8: Found 1 AMD FX(tm)-6100 Six-Core Processor (6 cpu cores) (version 2.20.00)
[ 2.144965] powernow-k8: Core Performance Boosting: on.
[ 2.145053] powernow-k8: 0 : pstate 0 (3300 MHz)
[ 2.145056] powernow-k8: 1 : pstate 1 (3000 MHz)
[ 2.145060] powernow-k8: 2 : pstate 2 (2400 MHz)
[ 2.145063] powernow-k8: 3 : pstate 3 (1800 MHz)
[ 2.145066] powernow-k8: 4 : pstate 4 (1400 MHz)
[ 2.146050] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.146055] EDD information not available.
[ 2.146362] Freeing unused kernel memory: 720k freed
[ 2.146775] Write protecting the kernel text: 5524k
[ 2.146946] Write protecting the kernel read-only data: 2240k
[ 2.146949] NX-protecting the kernel data: 4716k
[ 2.186115] udevd[95]: starting version 173
[ 2.204283] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.204300] r8169 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 2.204334] r8169 0000:03:00.0: setting latency timer to 64
[ 2.204340] r8169 0000:03:00.0: (unregistered net_device): unknown MAC, using family default
[ 2.204398] r8169 0000:03:00.0: irq 40 for MSI/MSI-X
[ 2.205202] r8169 0000:03:00.0: eth0: RTL8168b/8111b at 0xf8420000, 50:e5:49:b9:2d:fd, XID 0c900800 IRQ 40
[ 2.205370] xhci_hcd 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.205393] xhci_hcd 0000:02:00.0: setting latency timer to 64
[ 2.205397] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 2.205456] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 8
[ 2.205540] xhci_hcd 0000:02:00.0: irq 16, io mem 0xfd4f8000
[ 2.205555] xhci_hcd 0000:02:00.0: Failed to enable MSI-X
[ 2.205590] xhci_hcd 0000:02:00.0: irq 41 for MSI/MSI-X
[ 2.205721] xHCI xhci_add_endpoint called for root hub
[ 2.205723] xHCI xhci_check_bandwidth called for root hub
[ 2.205753] hub 8-0:1.0: USB hub found
[ 2.205760] hub 8-0:1.0: 2 ports detected
[ 2.205821] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 2.205863] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 9
[ 2.205966] xHCI xhci_add_endpoint called for root hub
[ 2.205968] xHCI xhci_check_bandwidth called for root hub
[ 2.205997] hub 9-0:1.0: USB hub found
[ 2.206002] hub 9-0:1.0: 2 ports detected
[ 2.206059] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 2.206079] xhci_hcd 0000:04:00.0: setting latency timer to 64
[ 2.206082] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 2.206121] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 10
[ 2.206195] xhci_hcd 0000:04:00.0: irq 18, io mem 0xfdbf8000
[ 2.206206] xhci_hcd 0000:04:00.0: Failed to enable MSI-X
[ 2.206237] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X
[ 2.206358] xHCI xhci_add_endpoint called for root hub
[ 2.206361] xHCI xhci_check_bandwidth called for root hub
[ 2.206391] hub 10-0:1.0: USB hub found
[ 2.206397] hub 10-0:1.0: 2 ports detected
[ 2.206454] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 2.206491] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 11
[ 2.206604] xHCI xhci_add_endpoint called for root hub
[ 2.206606] xHCI xhci_check_bandwidth called for root hub
[ 2.206656] hub 11-0:1.0: USB hub found
[ 2.206666] hub 11-0:1.0: 2 ports detected
[ 2.208445] ahci 0000:00:11.0: version 3.0
[ 2.208468] ahci 0000:00:11.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 2.208566] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 4 ports 6 Gbps 0xf impl SATA mode
[ 2.208570] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
[ 2.211551] scsi0 : ahci
[ 2.211838] scsi1 : ahci
[ 2.213403] scsi2 : ahci
[ 2.214091] scsi3 : ahci
[ 2.214216] ata1: SATA max UDMA/133 abar m1024@0xfdfff000 port 0xfdfff100 irq 19
[ 2.214220] ata2: SATA max UDMA/133 abar m1024@0xfdfff000 port 0xfdfff180 irq 19
[ 2.214223] ata3: SATA max UDMA/133 abar m1024@0xfdfff000 port 0xfdfff200 irq 19
[ 2.214226] ata4: SATA max UDMA/133 abar m1024@0xfdfff000 port 0xfdfff280 irq 19
[ 2.218479] scsi4 : pata_atiixp
[ 2.218565] scsi5 : pata_atiixp
[ 2.219074] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfa00 irq 14
[ 2.219077] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfa08 irq 15
[ 2.277440] input: 2.4G Receiver as /devices/pci0000:00/0000:00:13.0/usb5/5-5/5-5:1.0/input/input2
[ 2.277497] generic-usb 0003:1D57:32DA.0001: input,hidraw0: USB HID v1.10 Keyboard [2.4G Receiver] on usb-0000:00:13.0-5/input0
[ 2.282414] input: 2.4G Receiver as /devices/pci0000:00/0000:00:13.0/usb5/5-5/5-5:1.1/input/input3
[ 2.282484] generic-usb 0003:1D57:32DA.0002: input,hidraw1: USB HID v1.10 Mouse [2.4G Receiver] on usb-0000:00:13.0-5/input1
[ 2.291173] input: 2.4G Receiver as /devices/pci0000:00/0000:00:13.0/usb5/5-5/5-5:1.2/input/input4
[ 2.291259] generic-usb 0003:1D57:32DA.0003: input,hidraw2: USB HID v1.10 Device [2.4G Receiver] on usb-0000:00:13.0-5/input2
[ 2.291275] usbcore: registered new interface driver usbhid
[ 2.291277] usbhid: USB HID core driver
[ 2.532127] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.536124] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.552339] usb 9-2: new SuperSpeed USB device number 2 using xhci_hcd
[ 2.571319] xhci_hcd 0000:02:00.0: WARN: short transfer on control ep
[ 2.572070] xhci_hcd 0000:02:00.0: WARN: short transfer on control ep
[ 2.572819] xhci_hcd 0000:02:00.0: WARN: short transfer on control ep
[ 2.573513] xhci_hcd 0000:02:00.0: WARN: short transfer on control ep
[ 2.576765] usbcore: registered new interface driver uas
[ 2.704133] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2.704162] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.704686] ata2.00: ATAPI: TSSTcorp CDDVDW SH-222AB, SB01, max UDMA/100
[ 2.705544] ata2.00: configured for UDMA/100
[ 2.779193] ata1.00: ATA-8: ST500DM002-1BD142, KC44, max UDMA/133
[ 2.779200] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 2.780833] ata1.00: configured for UDMA/133
[ 2.780922] scsi 0:0:0:0: Direct-Access ATA ST500DM002-1BD14 KC44 PQ: 0 ANSI: 5
[ 2.781054] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.781098] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 2.781102] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 2.781169] sd 0:0:0:0: [sda] Write Protect is off
[ 2.781171] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.781200] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.781692] scsi 1:0:0:0: CD-ROM TSSTcorp CDDVDW SH-222AB SB01 PQ: 0 ANSI: 5
[ 2.784174] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.784181] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.784361] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.784421] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 2.817721] sda: sda1 sda2 < sda5 >
[ 2.818144] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.819756] Initializing USB Mass Storage driver...
[ 2.819881] scsi6 : usb-storage 9-2:1.0
[ 2.820354] firewire_ohci 0000:05:0e.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 2.820622] usbcore: registered new interface driver usb-storage
[ 2.820626] USB Mass Storage support registered.
[ 2.884189] firewire_ohci: Added fw-ohci device 0000:05:0e.0, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x11
[ 3.214710] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[ 3.214712] EXT4-fs (sda1): write access will be enabled during recovery
[ 3.384245] firewire_core: created device fw0: GUID 0049e550dff60400, S400
[ 3.820776] scsi 6:0:0:0: Direct-Access WD My Book 1140 1003 PQ: 0 ANSI: 6
[ 3.820923] scsi 6:0:0:1: Enclosure WD SES Device 1003 PQ: 0 ANSI: 6
[ 4.036395] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 4.036521] scsi 6:0:0:1: Attached scsi generic sg3 type 13
[ 4.036632] sd 6:0:0:0: [sdb] 1953458176 512-byte logical blocks: (1.00 TB/931 GiB)
[ 4.036760] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint
[ 4.037080] sd 6:0:0:0: [sdb] Write Protect is off
[ 4.037085] sd 6:0:0:0: [sdb] Mode Sense: 47 00 10 08
[ 4.037215] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint
[ 4.037831] sd 6:0:0:0: [sdb] No Caching mode page present
[ 4.037834] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 4.038210] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint
[ 4.038697] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint
[ 4.039072] sd 6:0:0:0: [sdb] No Caching mode page present
[ 4.039075] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 4.039274] sdb: sdb1
[ 4.039747] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint
[ 4.040193] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint
[ 4.040572] sd 6:0:0:0: [sdb] No Caching mode page present
[ 4.040574] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 4.040576] sd 6:0:0:0: [sdb] Attached SCSI disk
[ 4.043253] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint
[ 4.043799] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint
[ 4.044545] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint
[ 4.045425] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint
[ 4.046048] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint
[ 4.047465] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint
[ 4.049400] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint
[ 4.049888] ses 6:0:0:1: Attached Enclosure device
[ 32.995347] EXT4-fs (sda1): orphan cleanup on readonly fs
[ 33.044283] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 530486
[ 33.044389] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 527264
[ 33.044452] EXT4-fs (sda1): 2 orphan inodes deleted
[ 33.044456] EXT4-fs (sda1): recovery complete
[ 33.324760] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 37.907178] udevd[351]: starting version 173
[ 38.279045] Adding 8368124k swap on /dev/sda5. Priority:-1 extents:1 across:8368124k
[ 39.034903] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 39.255775] lp: driver loaded but no devices found
[ 40.029825] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 40.170843] wmi: Mapper loaded
[ 40.355314] [drm] Initialized drm 1.1.0 20060810
[ 40.700020] SP5100 TCO timer: SP5100 TCO WatchDog Timer Driver v0.01
[ 40.700143] SP5100 TCO timer: mmio address 0xb8fe00 already in use
[ 40.889685] [drm] radeon defaulting to kernel modesetting.
[ 40.889687] [drm] radeon kernel modesetting enabled.
[ 40.889751] radeon 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 40.889756] radeon 0000:01:00.0: setting latency timer to 64
[ 40.889887] [drm] initializing kernel modesetting (JUNIPER 0x1002:0x68BA 0x1462:0x2142).
[ 40.889912] [drm] register mmio base: 0xFD5C0000
[ 40.889914] [drm] register mmio size: 131072
[ 40.890669] ATOM BIOS: 113
[ 40.890691] radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
[ 40.890694] radeon 0000:01:00.0: GTT: 512M 0x0000000040000000 - 0x000000005FFFFFFF
[ 40.895946] [drm] Detected VRAM RAM=1024M, BAR=256M
[ 40.895948] [drm] RAM width 128bits DDR
[ 40.896010] [TTM] Zone kernel: Available graphics memory: 397586 kiB.
[ 40.896012] [TTM] Zone highmem: Available graphics memory: 4125782 kiB.
[ 40.896013] [TTM] Initializing pool allocator.
[ 40.896031] [drm] radeon: 1024M of VRAM memory ready
[ 40.896032] [drm] radeon: 512M of GTT memory ready.
[ 40.896049] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 40.896050] [drm] Driver supports precise vblank timestamp query.
[ 40.896084] radeon 0000:01:00.0: irq 43 for MSI/MSI-X
[ 40.896089] radeon 0000:01:00.0: radeon: using MSI.
[ 40.896115] [drm] radeon: irq initialized.
[ 40.896119] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 40.896582] [drm] Loading JUNIPER Microcode
[ 41.953952] type=1400 audit(1327954405.306:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=687 comm="apparmor_parser"
[ 41.953963] type=1400 audit(1327954405.306:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=688 comm="apparmor_parser"
[ 41.954214] type=1400 audit(1327954405.306:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=687 comm="apparmor_parser"
[ 41.954228] type=1400 audit(1327954405.306:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=688 comm="apparmor_parser"
[ 41.954399] type=1400 audit(1327954405.306:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=687 comm="apparmor_parser"
[ 41.954406] type=1400 audit(1327954405.306:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=688 comm="apparmor_parser"
[ 42.154089] radeon 0000:01:00.0: WB enabled
[ 42.170135] [drm] ring test succeeded in 1 usecs
[ 42.170238] [drm] radeon: ib pool ready.
[ 42.170296] [drm] ib test succeeded in 0 usecs
[ 42.170301] failed to evaluate ATIF got AE_BAD_PARAMETER
[ 42.170811] [drm] Radeon Display Connectors
[ 42.170814] [drm] Connector 0:
[ 42.170815] [drm] HDMI-A
[ 42.170816] [drm] HPD2
[ 42.170819] [drm] DDC: 0x6460 0x6460 0x6464 0x6464 0x6468 0x6468 0x646c 0x646c
[ 42.170820] [drm] Encoders:
[ 42.170821] [drm] DFP1: INTERNAL_UNIPHY2
[ 42.170823] [drm] Connector 1:
[ 42.170824] [drm] DVI-I
[ 42.170825] [drm] HPD1
[ 42.170827] [drm] DDC: 0x6450 0x6450 0x6454 0x6454 0x6458 0x6458 0x645c 0x645c
[ 42.170829] [drm] Encoders:
[ 42.170830] [drm] DFP2: INTERNAL_UNIPHY1
[ 42.170831] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 42.170833] [drm] Connector 2:
[ 42.170834] [drm] VGA
[ 42.170836] [drm] DDC: 0x6440 0x6440 0x6444 0x6444 0x6448 0x6448 0x644c 0x644c
[ 42.170838] [drm] Encoders:
[ 42.170839] [drm] CRT2: INTERNAL_KLDSCP_DAC2
[ 42.180640] [drm] Radeon display connector HDMI-A-1: No monitor connected or invalid EDID
[ 42.233246] [drm] Radeon display connector DVI-I-1: Found valid EDID
[ 42.243040] [drm] Radeon display connector VGA-1: No monitor connected or invalid EDID
[ 42.243061] [drm] Internal thermal controller with fan control
[ 42.243100] [drm] radeon: power management initialized
[ 42.324861] [drm] fb mappable at 0xD0141000
[ 42.324866] [drm] vram apper at 0xD0000000
[ 42.324870] [drm] size 8294400
[ 42.324873] [drm] fb depth is 24
[ 42.324876] [drm] pitch is 7680
[ 42.324993] fbcon: radeondrmfb (fb0) is primary device
[ 42.325221] Console: switching to colour frame buffer device 240x67
[ 42.325310] fb0: radeondrmfb frame buffer device
[ 42.325313] drm: registered panic notifier
[ 42.325322] [drm] Initialized radeon 2.10.0 20080528 for 0000:01:00.0 on minor 0
[ 43.558219] init: failsafe main process (778) killed by TERM signal
[ 43.770918] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 43.865780] hda_codec: ALC889: BIOS auto-probing.
[ 43.875889] input: HDA ATI SB Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input5
[ 43.876038] HDA Intel 0000:01:00.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 43.876097] HDA Intel 0000:01:00.1: irq 44 for MSI/MSI-X
[ 43.876116] HDA Intel 0000:01:00.1: setting latency timer to 64
[ 43.982382] HDMI status: Pin=3 Presence_Detect=0 ELD_Valid=0
[ 43.982460] input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input6
[ 46.572364] [drm] force priority to high
[ 46.649155] ppdev: user-space parallel port driver
[ 46.772125] [drm] force priority to high
[ 46.859776] type=1400 audit(1327954410.210:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=954 comm="apparmor_parser"
[ 46.860115] type=1400 audit(1327954410.214:9): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=954 comm="apparmor_parser"
[ 46.884431] type=1400 audit(1327954410.238:10): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=957 comm="apparmor_parser"
[ 46.884701] type=1400 audit(1327954410.238:11): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=957 comm="apparmor_parser"
[ 47.155231] audit_printk_skb: 9 callbacks suppressed
[ 47.155233] type=1400 audit(1327954410.506:15): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm-guest-session-wrapper" pid=956 comm="apparmor_parser"
[ 47.168481] type=1400 audit(1327954410.522:16): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=962 comm="apparmor_parser"
[ 47.170671] type=1400 audit(1327954410.522:17): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=960 comm="apparmor_parser"
[ 47.170927] type=1400 audit(1327954410.522:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=960 comm="apparmor_parser"
[ 47.432955] r8169 0000:03:00.0: eth0: link down
[ 47.433021] r8169 0000:03:00.0: eth0: link down
[ 47.433105] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 47.547526] type=1400 audit(1327954410.898:19): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=958 comm="apparmor_parser"
[ 47.551112] type=1400 audit(1327954410.902:20): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=958 comm="apparmor_parser"
[ 47.553276] type=1400 audit(1327954410.906:21): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=958 comm="apparmor_parser"
[ 48.016785] init: apport pre-start process (998) terminated with status 1
[ 48.019091] init: apport post-stop process (1024) terminated with status 1
[ 49.082475] r8169 0000:03:00.0: eth0: link up
[ 49.082732] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 51.312867] Bluetooth: Core ver 2.16
[ 51.312885] NET: Registered protocol family 31
[ 51.312887] Bluetooth: HCI device and connection manager initialized
[ 51.312890] Bluetooth: HCI socket layer initialized
[ 51.312891] Bluetooth: L2CAP socket layer initialized
[ 51.313065] Bluetooth: SCO socket layer initialized
[ 51.339995] Bluetooth: RFCOMM TTY layer initialized
[ 51.339999] Bluetooth: RFCOMM socket layer initialized
[ 51.340008] Bluetooth: RFCOMM ver 1.11
[ 51.366317] [drm] force priority to high
[ 51.471089] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 51.471091] Bluetooth: BNEP filters: protocol multicast
[ 53.888056] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[ 54.602283] init: plymouth-stop pre-start process (1320) terminated with status 1
[ 58.370469] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[ 59.792089] eth0: no IPv6 routers present
[ 130.720178] r8169 0000:03:00.0: eth0: link up
[ 137.760173] r8169 0000:03:00.0: eth0: link up
[ 379.076122] r8169 0000:03:00.0: eth0: link up]
αυτά ευχαριστώ πάντως .