Δημοσιεύτηκε: 10 Ιουν 2010, 19:40
@logari81 - ευχαριστω για την προσπαθεια , εκανα ο,τι ειπες και παρακατω ειναι τα αποτελεσματα
lspci -nn
lsusb
dmesg
lspci -nn
- Κώδικας: Επιλογή όλων
00:00.0 Host bridge [0600]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller [8086:3580] (rev 02)
00:00.1 System peripheral [0880]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller [8086:3584] (rev 02)
00:00.3 System peripheral [0880]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller [8086:3585] (rev 02)
00:02.0 VGA compatible controller [0300]: Intel Corporation 82852/855GM Integrated Graphics Device [8086:3582] (rev 02)
00:02.1 Display controller [0380]: Intel Corporation 82852/855GM Integrated Graphics Device [8086:3582] (rev 02)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 [8086:24c2] (rev 03)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 [8086:24c4] (rev 03)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller [8086:24cd] (rev 03)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 83)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge [8086:24cc] (rev 03)
00:1f.1 IDE interface [0101]: Intel Corporation 82801DBM (ICH4-M) IDE Controller [8086:24ca] (rev 03)
00:1f.3 SMBus [0c05]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller [8086:24c3] (rev 03)
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller [8086:24c5] (rev 03)
00:1f.6 Modem [0703]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller [8086:24c6] (rev 03)
02:01.0 CardBus bridge [0607]: Texas Instruments PCI1410 PC card Cardbus Controller [104c:ac50] (rev 02)
02:02.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
03:00.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 62)
03:00.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 62)
03:00.2 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 65)
lsusb
- Κώδικας: Επιλογή όλων
Bus 006 Device 002: ID 07d1:3c0f D-Link System
Bus 006 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 045e:007d Microsoft Corp. Notebook Optical Mouse
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
dmesg
- Κώδικας: Επιλογή όλων
[ 6.000879] device-mapper: multipath: version 1.1.0 loaded
[ 6.000882] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 6.001042] EISA: Probing bus 0 at eisa.0
[ 6.001050] Cannot allocate resource for EISA slot 1
[ 6.001053] Cannot allocate resource for EISA slot 2
[ 6.001056] Cannot allocate resource for EISA slot 3
[ 6.001078] EISA: Detected 0 cards.
[ 6.001181] cpuidle: using governor ladder
[ 6.001258] cpuidle: using governor menu
[ 6.001874] TCP cubic registered
[ 6.002078] NET: Registered protocol family 10
[ 6.002607] lo: Disabled Privacy Extensions
[ 6.002985] NET: Registered protocol family 17
[ 6.003009] Bluetooth: L2CAP ver 2.13
[ 6.003012] Bluetooth: L2CAP socket layer initialized
[ 6.003015] Bluetooth: SCO (Voice Link) ver 0.6
[ 6.003018] Bluetooth: SCO socket layer initialized
[ 6.003059] Bluetooth: RFCOMM TTY layer initialized
[ 6.003062] Bluetooth: RFCOMM socket layer initialized
[ 6.003065] Bluetooth: RFCOMM ver 1.11
[ 6.003191] Using IPI No-Shortcut mode
[ 6.003280] PM: Resume from disk failed.
[ 6.003296] registered taskstats version 1
[ 6.003422] Magic number: 14:923:539
[ 6.003526] rtc_cmos 00:01: setting system clock to 2010-06-10 16:32:16 UTC (1276187536)
[ 6.003531] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 6.003533] EDD information not available.
[ 6.031961] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 6.144686] ata2.00: ATAPI: MATSHITADVD-RAM UJ-830S, 1.80, max UDMA/33
[ 6.144982] ata1.00: ATA-6: TOSHIBA MK4025GAS, KA100U, max UDMA/100
[ 6.144987] ata1.00: 78140160 sectors, multi 16: LBA
[ 6.160499] ata2.00: configured for UDMA/33
[ 6.160714] ata1.00: configured for UDMA/100
[ 6.160899] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK4025GA KA10 PQ: 0 ANSI: 5
[ 6.161063] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 6.161114] sd 0:0:0:0: [sda] 78140160 512-byte logical blocks: (40.0 GB/37.2 GiB)
[ 6.161175] sd 0:0:0:0: [sda] Write Protect is off
[ 6.161179] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.161209] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.161375] sda:
[ 6.163357] scsi 1:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-830S 1.80 PQ: 0 ANSI: 5
[ 6.167860] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 6.167864] Uniform CD-ROM driver Revision: 3.20
[ 6.167973] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 6.168046] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 6.214935] sda1 sda2 < sda5 >
[ 6.237691] sd 0:0:0:0: [sda] Attached SCSI disk
[ 6.237711] Freeing unused kernel memory: 540k freed
[ 6.238104] Write protecting the kernel text: 4568k
[ 6.238153] Write protecting the kernel read-only data: 1836k
[ 6.257518] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 6.257528] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 6.399356] [Firmware Bug]: ACPI: ACPI brightness control misses _BQC function
[ 6.399593] acpi device:06: registered as cooling_device3
[ 6.399727] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:02/input/input4
[ 6.399788] ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no)
[ 6.461943] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 6.461953] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 6.495122] Linux agpgart interface v0.103
[ 6.499831] agpgart-intel 0000:00:00.0: Intel 855GM Chipset
[ 6.500302] agpgart-intel 0000:00:00.0: detected 16252K stolen memory
[ 6.539515] <6>8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 6.539562] 8139cp 0000:02:02.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 6.543763] 8139too Fast Ethernet driver 0.9.28
[ 6.543816] 8139too 0000:02:02.0: PCI INT A -> Link[LNKD] -> GSI 6 (level, low) -> IRQ 6
[ 6.546013] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xe8000000
[ 6.599460] eth0: RealTek RTL8139 at 0x3800, 00:c0:9f:83:78:88, IRQ 6
[ 6.614647] [drm] Initialized drm 1.1.0 20060810
[ 6.634524] i915 0000:00:02.0: PCI INT A -> Link[LNKA] -> GSI 6 (level, low) -> IRQ 6
[ 6.634532] i915 0000:00:02.0: setting latency timer to 64
[ 6.743622] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 6.743630] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 7.212011] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 7.213104] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 7.281683] [drm] DAC-6: set mode 640x480 0
[ 7.663068] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 7.663073] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 7.663076] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 7.755253] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 7.755263] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 7.878432] [drm] fb0: inteldrmfb frame buffer device
[ 7.878447] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 7.958388] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 7.958397] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 7.966853] render error detected, EIR: 0x00000010
[ 7.966858] [drm:i915_handle_error] *ERROR* EIR stuck: 0x00000010, masking
[ 7.966873] render error detected, EIR: 0x00000010
[ 7.979996] [drm] LVDS-8: set mode 1024x768 10
[ 8.027692] Console: switching to colour frame buffer device 128x48
[ 8.165486] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 8.165496] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 8.339312] PM: Starting manual resume from disk
[ 8.339318] PM: Resume from partition 8:5
[ 8.339321] PM: Checking hibernation image.
[ 8.339507] PM: Resume from disk failed.
[ 8.364943] EXT4-fs (sda1): barriers enabled
[ 8.369509] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 8.369594] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 8.388479] kjournald2 starting: pid 335, dev sda1:8, commit interval 5 seconds
[ 8.388497] EXT4-fs (sda1): delayed allocation enabled
[ 8.388501] EXT4-fs: file extents enabled
[ 8.393777] EXT4-fs: mballoc enabled
[ 8.393798] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 8.573488] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 8.573511] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 8.573514] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 8.629482] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 8.629505] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 8.833483] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 8.833491] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 9.037495] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 9.037505] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 9.241486] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 9.241495] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 9.303229] type=1505 audit(1276187539.798:2): operation="profile_load" pid=358 name=/usr/share/gdm/guest-session/Xsession
[ 9.306383] type=1505 audit(1276187539.800:3): operation="profile_load" pid=359 name=/sbin/dhclient3
[ 9.307227] type=1505 audit(1276187539.800:4): operation="profile_load" pid=359 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[ 9.307689] type=1505 audit(1276187539.800:5): operation="profile_load" pid=359 name=/usr/lib/connman/scripts/dhclient-script
[ 9.373031] type=1505 audit(1276187539.868:6): operation="profile_load" pid=360 name=/usr/bin/evince
[ 9.386884] type=1505 audit(1276187539.880:7): operation="profile_load" pid=360 name=/usr/bin/evince-previewer
[ 9.394988] type=1505 audit(1276187539.888:8): operation="profile_load" pid=360 name=/usr/bin/evince-thumbnailer
[ 9.424150] type=1505 audit(1276187539.920:9): operation="profile_load" pid=362 name=/usr/lib/cups/backend/cups-pdf
[ 9.425150] type=1505 audit(1276187539.920:10): operation="profile_load" pid=362 name=/usr/sbin/cupsd
[ 9.428607] type=1505 audit(1276187539.924:11): operation="profile_load" pid=363 name=/usr/sbin/tcpdump
[ 9.445608] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 9.445618] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 9.445621] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 9.501534] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 9.501565] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 9.705493] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 9.705502] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 9.909488] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 9.909497] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 10.113581] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 10.113657] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 10.317514] ehci_hcd 0000:00:1d.7: port 1 reset error -110
[ 10.317596] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 10.317600] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 10.317616] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 10.385488] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 10.385493] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 10.589486] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 10.589491] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 10.793503] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 10.793513] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 10.904554] Adding 1445808k swap on /dev/sda5. Priority:-1 extents:1 across:1445808k
[ 10.954974] udev: starting version 147
[ 10.997500] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 10.997510] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 11.134146] EXT4-fs (sda1): internal journal on sda1:8
[ 11.201496] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 11.201506] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 11.201510] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 11.257804] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 11.257889] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 11.461516] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 11.461660] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 11.665488] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 11.665499] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 11.869490] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 11.869500] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 12.074358] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 12.074369] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 12.074373] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 12.129510] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 12.129521] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 12.333515] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 12.333545] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 12.422884] intel_rng: FWH not detected
[ 12.537492] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 12.537574] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 12.741505] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 12.741517] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 12.895693] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 12.947890] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 12.947903] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 12.947907] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 12.957979] lp: driver loaded but no devices found
[ 13.001491] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 13.001502] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 13.205501] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 13.205513] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 13.409488] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 13.409500] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 13.613494] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 13.613523] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 13.817501] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 13.817512] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 13.817516] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 13.817533] hub 1-0:1.0: unable to enumerate USB device on port 2
[ 13.885487] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 13.885498] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 14.089488] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 14.089499] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 14.184332] yenta_cardbus 0000:02:01.0: CardBus bridge found [1179:ff31]
[ 14.184353] yenta_cardbus 0000:02:01.0: Using CSCINT to route CSC interrupts to PCI
[ 14.184356] yenta_cardbus 0000:02:01.0: Routing CardBus interrupts to PCI
[ 14.184362] yenta_cardbus 0000:02:01.0: TI: mfunc 0x015c1d22, devctl 0x44
[ 14.293504] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 14.293551] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 14.416561] yenta_cardbus 0000:02:01.0: ISA IRQ mask 0x00b8, PCI irq 10
[ 14.416567] yenta_cardbus 0000:02:01.0: Socket status: 30000020
[ 14.416573] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #02 to #06
[ 14.416587] yenta_cardbus 0000:02:01.0: pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
[ 14.416592] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3000-0x3fff: clean.
[ 14.416887] yenta_cardbus 0000:02:01.0: pcmcia: parent PCI bridge Memory window: 0xe0200000 - 0xe04fffff
[ 14.416891] yenta_cardbus 0000:02:01.0: pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x23ffffff
[ 14.498160] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 14.498199] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 14.521404] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.701492] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 14.701513] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 14.701517] hub 1-0:1.0: Cannot enable port 3. Maybe the USB cable is bad?
[ 14.759399] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 14.759411] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 14.962528] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 14.962553] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 15.059415] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
[ 15.059467] pci 0000:03:00.0: reg 14 32bit mmio: [0x000000-0x0000ff]
[ 15.059487] pci 0000:03:00.0: reg 20 io port: [0xfce0-0xfcff]
[ 15.059523] pci 0000:03:00.0: supports D1 D2
[ 15.059527] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 15.059533] pci 0000:03:00.0: PME# disabled
[ 15.059577] pci 0000:03:00.1: reg 14 32bit mmio: [0x000000-0x0000ff]
[ 15.059596] pci 0000:03:00.1: reg 20 io port: [0xfce0-0xfcff]
[ 15.059628] pci 0000:03:00.1: supports D1 D2
[ 15.059631] pci 0000:03:00.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 15.059637] pci 0000:03:00.1: PME# disabled
[ 15.059675] pci 0000:03:00.2: reg 10 32bit mmio: [0x000000-0x0000ff]
[ 15.059684] pci 0000:03:00.2: reg 14 32bit mmio: [0x000000-0x0000ff]
[ 15.059731] pci 0000:03:00.2: supports D1 D2
[ 15.059734] pci 0000:03:00.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 15.059739] pci 0000:03:00.2: PME# disabled
[ 15.059930] uhci_hcd 0000:03:00.0: enabling device (0000 -> 0003)
[ 15.059944] uhci_hcd 0000:03:00.0: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
[ 15.059960] uhci_hcd 0000:03:00.0: UHCI Host Controller
[ 15.060090] uhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 4
[ 15.060124] uhci_hcd 0000:03:00.0: irq 10, io base 0x00003000
[ 15.060253] usb usb4: configuration #1 chosen from 1 choice
[ 15.060299] hub 4-0:1.0: USB hub found
[ 15.060309] hub 4-0:1.0: 2 ports detected
[ 15.060430] uhci_hcd 0000:03:00.1: enabling device (0000 -> 0003)
[ 15.060439] uhci_hcd 0000:03:00.1: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
[ 15.060450] uhci_hcd 0000:03:00.1: UHCI Host Controller
[ 15.060494] uhci_hcd 0000:03:00.1: new USB bus registered, assigned bus number 5
[ 15.060519] uhci_hcd 0000:03:00.1: irq 10, io base 0x00003020
[ 15.060620] usb usb5: configuration #1 chosen from 1 choice
[ 15.060664] hub 5-0:1.0: USB hub found
[ 15.060672] hub 5-0:1.0: 2 ports detected
[ 15.060777] ehci_hcd 0000:03:00.2: enabling device (0000 -> 0002)
[ 15.060785] ehci_hcd 0000:03:00.2: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
[ 15.060819] ehci_hcd 0000:03:00.2: EHCI Host Controller
[ 15.060871] ehci_hcd 0000:03:00.2: new USB bus registered, assigned bus number 6
[ 15.060922] ehci_hcd 0000:03:00.2: irq 10, io mem 0x28000200
[ 15.117277] Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 15.117320] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 15.165486] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 15.165505] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 15.267539] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x256eb1, caps: 0x804713/0x0
[ 15.267549] synaptics: Toshiba Satellite L10 detected, limiting rate to 40pps.
[ 15.301821] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input5
[ 15.369488] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 15.369513] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 15.436091] intel8x0_measure_ac97_clock: measured 54156 usecs (2609 samples)
[ 15.436096] intel8x0: clocking to 48000
[ 15.573724] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 15.573753] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 15.573756] hub 1-0:1.0: Cannot enable port 3. Maybe the USB cable is bad?
[ 15.584032] ehci_hcd 0000:03:00.2: USB 2.0 started, EHCI 1.00
[ 15.584226] usb usb6: configuration #1 chosen from 1 choice
[ 15.584272] hub 6-0:1.0: USB hub found
[ 15.584283] hub 6-0:1.0: 4 ports detected
[ 15.643181] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 15.643193] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 15.686998] type=1505 audit(1276187546.180:12): operation="profile_replace" pid=742 name=/usr/share/gdm/guest-session/Xsession
[ 15.689231] type=1505 audit(1276187546.184:13): operation="profile_replace" pid=743 name=/sbin/dhclient3
[ 15.690078] type=1505 audit(1276187546.184:14): operation="profile_replace" pid=743 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[ 15.690616] type=1505 audit(1276187546.184:15): operation="profile_replace" pid=743 name=/usr/lib/connman/scripts/dhclient-script
[ 15.698063] type=1505 audit(1276187546.192:16): operation="profile_replace" pid=744 name=/usr/bin/evince
[ 15.712594] type=1505 audit(1276187546.208:17): operation="profile_replace" pid=744 name=/usr/bin/evince-previewer
[ 15.720634] type=1505 audit(1276187546.216:18): operation="profile_replace" pid=744 name=/usr/bin/evince-thumbnailer
[ 15.732485] type=1505 audit(1276187546.228:19): operation="profile_replace" pid=746 name=/usr/lib/cups/backend/cups-pdf
[ 15.733516] type=1505 audit(1276187546.228:20): operation="profile_replace" pid=746 name=/usr/sbin/cupsd
[ 15.736695] type=1505 audit(1276187546.232:21): operation="profile_replace" pid=747 name=/usr/sbin/tcpdump
[ 15.846141] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 15.846172] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 15.868992] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[ 15.870581] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
[ 15.871272] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 15.871850] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 15.872634] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 16.049492] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 16.049502] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 16.253491] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 16.253516] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 16.457489] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 16.457500] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 16.457504] hub 1-0:1.0: Cannot enable port 3. Maybe the USB cable is bad?
[ 16.513489] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 16.513501] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 16.717492] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 16.717503] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 16.921491] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 16.921504] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 17.125493] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 17.125504] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 17.329496] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 17.329614] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 17.329619] hub 1-0:1.0: Cannot enable port 3. Maybe the USB cable is bad?
[ 17.329635] hub 1-0:1.0: unable to enumerate USB device on port 3
[ 17.398451] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 17.398463] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 17.601506] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 17.601539] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 17.805502] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 17.805512] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 18.009512] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 18.009520] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 18.213493] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 18.213517] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 18.213521] hub 1-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
[ 18.272015] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 18.272119] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 18.477496] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 18.477507] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 18.630588] ppdev: user-space parallel port driver
[ 18.681494] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 18.681505] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 18.885498] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 18.885510] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 19.089562] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 19.089641] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 19.089645] hub 1-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
[ 19.145491] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 19.145497] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 19.349485] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 19.349496] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 19.553492] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 19.553504] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 19.757487] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 19.757566] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 19.961490] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 19.961502] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 19.961506] hub 1-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
[ 20.017489] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 20.017523] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 20.221488] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 20.221499] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 20.425488] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 20.425500] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 20.629517] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 20.629639] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 20.833530] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 20.833610] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 20.833614] hub 1-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
[ 20.833631] hub 1-0:1.0: unable to enumerate USB device on port 4
[ 20.901494] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 20.901501] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 21.105513] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 21.105524] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 21.309504] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 21.309514] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 21.513496] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 21.513503] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 21.717504] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 21.717516] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 21.717520] hub 1-0:1.0: Cannot enable port 6. Maybe the USB cable is bad?
[ 21.773485] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 21.773523] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 21.977507] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 21.977518] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 22.181497] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 22.181576] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 22.385493] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 22.385564] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 22.589783] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 22.589865] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 22.589922] hub 1-0:1.0: Cannot enable port 6. Maybe the USB cable is bad?
[ 22.645487] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 22.645569] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 22.849500] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 22.849581] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 22.907996] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 23.069801] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 23.069887] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 23.273509] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 23.273589] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 23.477495] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 23.477570] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 23.477626] hub 1-0:1.0: Cannot enable port 6. Maybe the USB cable is bad?
[ 23.533491] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 23.533572] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 23.737555] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 23.737635] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 23.941487] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 23.941567] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 24.145491] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 24.145502] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 24.349497] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 24.349505] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 24.349508] hub 1-0:1.0: Cannot enable port 6. Maybe the USB cable is bad?
[ 24.349524] hub 1-0:1.0: unable to enumerate USB device on port 6
[ 24.728041] usb 6-1: new high speed USB device using ehci_hcd and address 2
[ 24.878173] usb 6-1: configuration #1 chosen from 1 choice
[ 25.126412] [drm] DAC-6: set mode 640x480 0
[ 25.561015] usb 4-2: new low speed USB device using uhci_hcd and address 2
[ 25.630540] [drm] DAC-6: set mode 640x480 0
[ 26.259512] [drm] DAC-6: set mode 640x480 0
[ 26.758914] [drm] DAC-6: set mode 640x480 0
[ 27.139221] usb 4-2: configuration #1 chosen from 1 choice
[ 27.292597] usbcore: registered new interface driver hiddev
[ 27.305936] input: Microsoft Microsoft 3-Button Mouse with IntelliEye™ as /devices/pci0000:00/0000:00:1e.0/0000:02:01.0/0000:03:00.0/usb4/4-2/4-2:1.0/input/input6
[ 27.306080] generic-usb 0003:045E:007D.0001: input,hidraw0: USB HID v1.00 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye™] on usb-0000:03:00.0-2/input0
[ 27.306108] usbcore: registered new interface driver usbhid
[ 27.306112] usbhid: v2.6:USB HID core driver
[ 32.992040] eth0: no IPv6 routers present
[ 33.032073] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 36.000081] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 38.968055] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 41.936076] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 44.904072] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 47.872063] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 50.840059] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 53.808062] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 55.304338] [drm] DAC-6: set mode 640x480 0
[ 55.801307] [drm] DAC-6: set mode 640x480 0
[ 56.430209] [drm] DAC-6: set mode 640x480 0
[ 56.926269] [drm] DAC-6: set mode 640x480 0
[ 57.570589] [drm] DAC-6: set mode 640x480 0
[ 58.067074] [drm] DAC-6: set mode 640x480 0
[ 58.447206] hub 1-0:1.0: Cannot enable port 3. Maybe the USB cable is bad?
[ 61.504065] hub 1-0:1.0: Cannot enable port 3. Maybe the USB cable is bad?
[ 64.472062] hub 1-0:1.0: Cannot enable port 3. Maybe the USB cable is bad?
[ 67.440065] hub 1-0:1.0: Cannot enable port 3. Maybe the USB cable is bad?
[ 70.408059] hub 1-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
[ 73.376051] hub 1-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
[ 76.344047] hub 1-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
[ 79.312056] hub 1-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
[ 82.280053] hub 1-0:1.0: Cannot enable port 6. Maybe the USB cable is bad?
[ 85.248053] hub 1-0:1.0: Cannot enable port 6. Maybe the USB cable is bad?
[ 88.216064] hub 1-0:1.0: Cannot enable port 6. Maybe the USB cable is bad?
[ 91.184056] hub 1-0:1.0: Cannot enable port 6. Maybe the USB cable is bad?
[ 99.639886] [drm] DAC-6: set mode 640x480 0
[ 100.137381] [drm] DAC-6: set mode 640x480 0
[ 100.779760] [drm] DAC-6: set mode 640x480 0
[ 101.276659] [drm] DAC-6: set mode 640x480 0
[ 101.925725] [drm] DAC-6: set mode 640x480 0
[ 102.440995] [drm] DAC-6: set mode 640x480 0
[ 169.872060] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 172.852061] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 175.844061] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 178.864057] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 181.840071] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 184.808076] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 187.776070] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 190.744064] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 193.724081] hub 1-0:1.0: Cannot enable port 3. Maybe the USB cable is bad?
[ 196.696054] hub 1-0:1.0: Cannot enable port 3. Maybe the USB cable is bad?
[ 199.664072] hub 1-0:1.0: Cannot enable port 3. Maybe the USB cable is bad?
[ 202.632064] hub 1-0:1.0: Cannot enable port 3. Maybe the USB cable is bad?
[ 205.612048] hub 1-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
[ 208.580077] hub 1-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
[ 211.548048] hub 1-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
[ 214.516062] hub 1-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
[ 217.484057] hub 1-0:1.0: Cannot enable port 6. Maybe the USB cable is bad?
[ 220.452066] hub 1-0:1.0: Cannot enable port 6. Maybe the USB cable is bad?
[ 223.424054] hub 1-0:1.0: Cannot enable port 6. Maybe the USB cable is bad?
[ 226.392073] hub 1-0:1.0: Cannot enable port 6. Maybe the USB cable is bad?
[ 287.232075] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 290.200181] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 293.168066] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 296.136073] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 299.104072] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 300.033557] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 300.033568] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 300.237546] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 300.237557] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 300.441549] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 300.441558] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 300.645541] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 300.645549] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 300.645553] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 300.701560] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 300.701570] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 300.905555] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 300.905567] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 301.109563] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 301.109574] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 301.313553] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 301.313564] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 301.517528] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 301.517561] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 301.517564] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 301.573548] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 301.573558] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 301.777553] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 301.777564] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 301.981546] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 301.981556] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 302.185545] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 302.185570] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 302.389538] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[ 302.389549] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 302.389553] hub 1-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
[ 302.391061] ehci_hcd 0000:00:1d.7: port 3 reset error -110
[ 302.391064] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 302.392022] ehci_hcd 0000:00:1d.7: port 4 reset error -110
[ 302.392585] hub 1-0:1.0: hub_port_status failed (err = -32)
[ 302.394075] ehci_hcd 0000:00:1d.7: port 6 reset error -110
[ 302.394078] hub 1-0:1.0: hub_port_status failed (err = -32)
- Κώδικας: Επιλογή όλων
vm@vm:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
- Κώδικας: Επιλογή όλων
vm@vm:~$ sudo iwlist scan
[sudo] password for vm:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
- Κώδικας: Επιλογή όλων
vm@vm:~$ lsmod
Module Size Used by
usbhid 38208 0
binfmt_misc 8356 1
ppdev 6688 0
joydev 10272 0
snd_intel8x0 30168 2
snd_ac97_codec 101216 1 snd_intel8x0
ac97_bus 1532 1 snd_ac97_codec
snd_pcm_oss 37920 0
snd_mixer_oss 16028 1 snd_pcm_oss
snd_pcm 75296 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
pcmcia 36808 0
snd_seq_dummy 2656 0
iptable_filter 3100 0
psmouse 56180 0
serio_raw 5280 0
snd_seq_oss 28576 0
ip_tables 11692 1 iptable_filter
snd_seq_midi 6432 0
yenta_socket 24200 2
x_tables 16544 1 ip_tables
snd_rawmidi 22208 1 snd_seq_midi
rsrc_nonstatic 11644 1 yenta_socket
snd_seq_midi_event 6940 2 snd_seq_oss,snd_seq_midi
pcmcia_core 35792 3 pcmcia,yenta_socket,rsrc_nonstatic
lp 8964 0
snd_seq 50224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
shpchp 32272 0
parport 35340 2 ppdev,lp
snd_timer 22276 2 snd_pcm,snd_seq
snd_seq_device 6920 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 59204 14 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 7264 1 snd
snd_page_alloc 9156 2 snd_intel8x0,snd_pcm
fbcon 36640 72
tileblit 2460 1 fbcon
font 8124 1 fbcon
bitblit 5372 1 fbcon
softcursor 1756 1 bitblit
i915 221064 2
drm 159584 2 i915
i2c_algo_bit 5760 1 i915
8139too 22620 0
8139cp 19260 0
mii 5212 2 8139too,8139cp
intel_agp 27484 2 i915
agpgart 34988 2 drm,intel_agp
video 19380 1 i915
output 2780 1 video