Ubuntu-gr Forum

the_eye έγραψε:Μπορείς να το κάνεις και από livecd αυτο που σου προτείνω.

Κώδικας: Επιλογή όλων

deft ~ % sudo smartctl -a /dev/sda
smartctl 5.41 2011-06-09 r3365 [i686-linux-3.0.0-26-generic] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Model Family: Hitachi Travelstar 5K120
Device Model: Hitachi HTS541212H9AT00
Serial Number: HP0400BEG3S6UA
LU WWN Device Id: 5 000cca 519c1b447
Firmware Version: HP4OA23C
User Capacity: 120,034,123,776 bytes [120 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 1
Local Time is: Sun Jan 27 17:26:22 2013 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 69) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0
3 Spin_Up_Time 0x0007 121 121 033 Pre-fail Always - 3
4 Start_Stop_Count 0x0012 097 097 000 Old_age Always - 5914
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0
9 Power_On_Hours 0x0012 078 078 000 Old_age Always - 9777
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1438
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 95
193 Load_Cycle_Count 0x0012 001 001 000 Old_age Always - 1170490
194 Temperature_Celsius 0x0002 141 141 000 Old_age Always - 39 (Min/Max 1/59)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 116
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0

SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 2 occurred at disk power-on lifetime: 10135 hours (422 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 81 76 f9 ed Error: IDNF 1 sectors at LBA = 0x0df97681 = 234452609

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 81 76 f9 ed 00 14d+22:00:57.800 READ DMA
c8 00 08 57 49 e7 e1 00 14d+22:00:57.800 READ DMA
c8 00 08 77 1c e7 e1 00 14d+22:00:57.800 READ DMA
c8 00 08 b7 74 88 e7 00 14d+22:00:57.800 READ DMA
c8 00 08 87 40 e7 e1 00 14d+22:00:57.800 READ DMA

Error 1 occurred at disk power-on lifetime: 10135 hours (422 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 81 76 f9 ed Error: IDNF 1 sectors at LBA = 0x0df97681 = 234452609

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 81 76 f9 ed 00 14d+21:48:07.200 READ DMA
c8 00 38 6b f3 87 e0 00 14d+21:48:07.100 READ DMA
e7 00 00 00 00 00 a0 00 14d+21:48:06.700 FLUSH CACHE
ca 00 08 17 9c fc e6 00 14d+21:48:06.700 WRITE DMA
ca 00 18 3f 03 00 e0 00 14d+21:48:06.700 WRITE DMA

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 9792 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.


sotos21 έγραψε:Μια που έγραψες αυτό
για να δοκιμάσουμε το παρακάτω
Μπες στο μενού του grub, πάτησε την δεύτερη επιλογή και από εκεί επέλεξε recovery. Μετά διάλεξε τον root και εκεί δώσε την

Κώδικας: Επιλογή όλων

rm /home/το username σου/.ICEauthority

Επίσης όταν είσαι στον guest αν πατήσεις ctrl+alt+f2 σε βγάζει σε κονσόλα; Αν σε βγάζει συνδέσου κανονικά και γράψε startx μην τυχόν μπεις έτσι στον λογαριασμό σου.