Δημοσιεύτηκε: 06 Νοέμ 2011, 21:37
για ριξε κ εδω μια ματια
- Κώδικας: Επιλογή όλων
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD1200BEVT-22ZCT0
Serial Number: WD-WXC708C55676
Firmware Version: 11.01A11
User Capacity: 120.034.123.776 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Nov 6 20:35:49 2011 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (4560) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 57) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 159 156 021 Pre-fail Always - 1033
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2740
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 4151
10 Spin_Retry_Count 0x0033 100 095 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1942
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 122
193 Load_Cycle_Count 0x0032 180 180 000 Old_age Always - 61253
194 Temperature_Celsius 0x0022 096 084 000 Old_age Always - 47
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 24 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 24 occurred at disk power-on lifetime: 2134 hours (88 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3c 6c aa 64 e0 Error: UNC 60 sectors at LBA = 0x0064aa6c = 6597228
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 20 3c 6c aa 64 06 00 00:00:59.236 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:56.261 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:53.146 READ DMA EXT
25 20 04 68 aa 64 06 00 00:00:53.146 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:50.033 READ DMA EXT
Error 23 occurred at disk power-on lifetime: 2134 hours (88 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3c 6c aa 64 e0 Error: UNC 60 sectors at LBA = 0x0064aa6c = 6597228
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 20 3c 6c aa 64 06 00 00:00:56.261 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:53.146 READ DMA EXT
25 20 04 68 aa 64 06 00 00:00:53.146 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:50.033 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:46.923 READ DMA EXT
Error 22 occurred at disk power-on lifetime: 2134 hours (88 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3c 6c aa 64 e0 Error: UNC 60 sectors at LBA = 0x0064aa6c = 6597228
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 20 3c 6c aa 64 06 00 00:00:53.146 READ DMA EXT
25 20 04 68 aa 64 06 00 00:00:53.146 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:50.033 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:46.923 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:43.666 READ DMA EXT
Error 21 occurred at disk power-on lifetime: 2134 hours (88 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3c 6c aa 64 e0 Error: UNC 60 sectors at LBA = 0x0064aa6c = 6597228
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 20 3c 6c aa 64 06 00 00:00:50.033 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:46.923 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:43.666 READ DMA EXT
25 20 04 68 aa 64 06 00 00:00:43.665 READ DMA EXT
25 20 3b 2d aa 64 06 00 00:00:43.665 READ DMA EXT
Error 20 occurred at disk power-on lifetime: 2134 hours (88 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3c 6c aa 64 e0 Error: UNC 60 sectors at LBA = 0x0064aa6c = 6597228
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 20 3c 6c aa 64 06 00 00:00:46.923 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:43.666 READ DMA EXT
25 20 04 68 aa 64 06 00 00:00:43.665 READ DMA EXT
25 20 3b 2d aa 64 06 00 00:00:43.665 READ DMA EXT
25 20 05 28 aa 64 06 00 00:00:43.665 READ DMA EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.