Ubuntu-gr Forum

ενας η/υ στην εκκινηση του μου δηλωνει S.M.A.R.T. Failure

του εκανα ενα τσεκ με smartmontools
και μου επεστρεψε αυτο το log

Κώδικας: Επιλογή όλων

smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-23-generic] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA
Device Model: WDC WD1600BEVS-07RST0
Serial Number: WD-WXE807637478
LU WWN Device Id: 5 0014ee 2ab1b1e8c
Firmware Version: 04.01G04
User Capacity: 160.041.885.696 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sat Jun 9 22:42:13 2012 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 6780) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 87) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 115
3 Spin_Up_Time 0x0003 189 186 021 Pre-fail Always - 1508
4 Start_Stop_Count 0x0032 097 097 000 Old_age Always - 3072
5 Reallocated_Sector_Ct 0x0033 133 133 140 Pre-fail Always FAILING_NOW 536
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1507
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1636
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 476
193 Load_Cycle_Count 0x0032 189 189 000 Old_age Always - 34031
194 Temperature_Celsius 0x0022 100 091 000 Old_age Always - 47
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 4
198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0

SMART Error Log Version: 1
ATA Error Count: 80 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 80 occurred at disk power-on lifetime: 1480 hours (61 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 48 0c c1 e0 Error: UNC 8 sectors at LBA = 0x00c10c48 = 12651592

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 48 0c c1 11 08 00:12:38.200 READ DMA EXT
ef 10 02 00 00 00 00 08 00:12:38.199 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 08 00:12:38.199 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 00:12:38.199 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 00:12:38.199 SET FEATURES [Set transfer mode]

Error 79 occurred at disk power-on lifetime: 1480 hours (61 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 48 0c c1 e0 Error: UNC 8 sectors at LBA = 0x00c10c48 = 12651592

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 48 0c c1 11 08 00:12:35.179 READ DMA EXT
ef 10 02 00 00 00 00 08 00:12:35.179 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 08 00:12:35.179 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 00:12:35.179 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 00:12:35.179 SET FEATURES [Set transfer mode]

Error 78 occurred at disk power-on lifetime: 1480 hours (61 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 48 0c c1 e0 Error: UNC 8 sectors at LBA = 0x00c10c48 = 12651592

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 48 0c c1 11 08 00:12:32.338 READ DMA EXT
ef 10 02 00 00 00 00 08 00:12:32.337 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 08 00:12:32.337 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 00:12:32.337 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 00:12:32.337 SET FEATURES [Set transfer mode]

Error 77 occurred at disk power-on lifetime: 1480 hours (61 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 48 0c c1 e0 Error: UNC 8 sectors at LBA = 0x00c10c48 = 12651592

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 48 0c c1 11 08 00:12:29.153 READ DMA EXT
ef 10 02 00 00 00 00 08 00:12:29.153 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 08 00:12:29.153 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 00:12:29.153 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 00:12:29.153 SET FEATURES [Set transfer mode]

Error 76 occurred at disk power-on lifetime: 1480 hours (61 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 08 48 0c c1 e0 Error: AMNF 8 sectors at LBA = 0x00c10c48 = 12651592

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 48 0c c1 11 08 00:12:26.308 READ DMA EXT
ef 10 02 00 00 00 00 08 00:12:26.308 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 08 00:12:26.307 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 00:12:26.307 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 00:12:26.307 SET FEATURES [Set transfer mode]

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

και καθως δεν εχω προηγουμενες παρτιδες με τετοιου ειδους προβληματα αποφασισα να ρωτησω την γνωμη σας επι του θεματος.
καθε αποψη δεκτή!