Ubuntu-gr Forum

ενας η/υ στην εκκινηση του μου δηλωνει S.M.A.R.T. Failure

του εκανα ενα τσεκ με smartmontools
και μου επεστρεψε αυτο το log

Κώδικας: Επιλογή όλων

smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-23-generic] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Scorpio Blue Serial ATA
Device Model:     WDC WD1600BEVS-07RST0
Serial Number:    WD-WXE807637478
LU WWN Device Id: 5 0014ee 2ab1b1e8c
Firmware Version: 04.01G04
User Capacity:    160.041.885.696 bytes [160 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   7
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Sat Jun  9 22:42:13 2012 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status:  (0x00)   Offline data collection activity
               was never started.
               Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)   The previous self-test routine completed
               without error or no self-test has ever
               been run.
Total time to complete Offline
data collection:       ( 6780) seconds.
Offline data collection
capabilities:           (0x7b) SMART execute Offline immediate.
               Auto Offline data collection on/off support.
               Suspend Offline collection upon new
               command.
               Offline surface scan supported.
               Self-test supported.
               Conveyance Self-test supported.
               Selective Self-test supported.
SMART capabilities:            (0x0003)   Saves SMART data before entering
               power-saving mode.
               Supports SMART auto save timer.
Error logging capability:        (0x01)   Error logging supported.
               General Purpose Logging supported.
Short self-test routine
recommended polling time:     (   2) minutes.
Extended self-test routine
recommended polling time:     (  87) minutes.
Conveyance self-test routine
recommended polling time:     (   6) minutes.
SCT capabilities:           (0x103f)   SCT Status supported.
               SCT Error Recovery Control supported.
               SCT Feature Control supported.
               SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   200   200   051    Pre-fail  Always       -       115
  3 Spin_Up_Time            0x0003   189   186   021    Pre-fail  Always       -       1508
  4 Start_Stop_Count        0x0032   097   097   000    Old_age   Always       -       3072
  5 Reallocated_Sector_Ct   0x0033   133   133   140    Pre-fail  Always   FAILING_NOW 536
  7 Seek_Error_Rate         0x000f   200   200   051    Pre-fail  Always       -       0
  9 Power_On_Hours          0x0032   098   098   000    Old_age   Always       -       1507
10 Spin_Retry_Count        0x0013   100   100   051    Pre-fail  Always       -       0
11 Calibration_Retry_Count 0x0012   100   100   051    Old_age   Always       -       0
12 Power_Cycle_Count       0x0032   099   099   000    Old_age   Always       -       1636
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       476
193 Load_Cycle_Count        0x0032   189   189   000    Old_age   Always       -       34031
194 Temperature_Celsius     0x0022   100   091   000    Old_age   Always       -       47
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0012   200   200   000    Old_age   Always       -       4
198 Offline_Uncorrectable   0x0010   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0009   100   253   051    Pre-fail  Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 80 (device log contains only the most recent five errors)
   CR = Command Register [HEX]
   FR = Features Register [HEX]
   SC = Sector Count Register [HEX]
   SN = Sector Number Register [HEX]
   CL = Cylinder Low Register [HEX]
   CH = Cylinder High Register [HEX]
   DH = Device/Head Register [HEX]
   DC = Device Command Register [HEX]
   ER = Error register [HEX]
   ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 80 occurred at disk power-on lifetime: 1480 hours (61 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 48 0c c1 e0  Error: UNC 8 sectors at LBA = 0x00c10c48 = 12651592

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 48 0c c1 11 08      00:12:38.200  READ DMA EXT
  ef 10 02 00 00 00 00 08      00:12:38.199  SET FEATURES [Reserved for Serial ATA]
  27 00 00 00 00 00 00 08      00:12:38.199  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 00 08      00:12:38.199  IDENTIFY DEVICE
  ef 03 46 00 00 00 00 08      00:12:38.199  SET FEATURES [Set transfer mode]

Error 79 occurred at disk power-on lifetime: 1480 hours (61 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 48 0c c1 e0  Error: UNC 8 sectors at LBA = 0x00c10c48 = 12651592

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 48 0c c1 11 08      00:12:35.179  READ DMA EXT
  ef 10 02 00 00 00 00 08      00:12:35.179  SET FEATURES [Reserved for Serial ATA]
  27 00 00 00 00 00 00 08      00:12:35.179  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 00 08      00:12:35.179  IDENTIFY DEVICE
  ef 03 46 00 00 00 00 08      00:12:35.179  SET FEATURES [Set transfer mode]

Error 78 occurred at disk power-on lifetime: 1480 hours (61 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 48 0c c1 e0  Error: UNC 8 sectors at LBA = 0x00c10c48 = 12651592

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 48 0c c1 11 08      00:12:32.338  READ DMA EXT
  ef 10 02 00 00 00 00 08      00:12:32.337  SET FEATURES [Reserved for Serial ATA]
  27 00 00 00 00 00 00 08      00:12:32.337  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 00 08      00:12:32.337  IDENTIFY DEVICE
  ef 03 46 00 00 00 00 08      00:12:32.337  SET FEATURES [Set transfer mode]

Error 77 occurred at disk power-on lifetime: 1480 hours (61 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 48 0c c1 e0  Error: UNC 8 sectors at LBA = 0x00c10c48 = 12651592

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 48 0c c1 11 08      00:12:29.153  READ DMA EXT
  ef 10 02 00 00 00 00 08      00:12:29.153  SET FEATURES [Reserved for Serial ATA]
  27 00 00 00 00 00 00 08      00:12:29.153  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 00 08      00:12:29.153  IDENTIFY DEVICE
  ef 03 46 00 00 00 00 08      00:12:29.153  SET FEATURES [Set transfer mode]

Error 76 occurred at disk power-on lifetime: 1480 hours (61 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  01 51 08 48 0c c1 e0  Error: AMNF 8 sectors at LBA = 0x00c10c48 = 12651592

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 48 0c c1 11 08      00:12:26.308  READ DMA EXT
  ef 10 02 00 00 00 00 08      00:12:26.308  SET FEATURES [Reserved for Serial ATA]
  27 00 00 00 00 00 00 08      00:12:26.307  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 00 08      00:12:26.307  IDENTIFY DEVICE
  ef 03 46 00 00 00 00 08      00:12:26.307  SET FEATURES [Set transfer mode]

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

και καθως δεν εχω προηγουμενες παρτιδες με τετοιου ειδους προβληματα αποφασισα να ρωτησω την γνωμη σας επι του θεματος.
καθε αποψη δεκτή!