Δημοσιεύτηκε: 27 Φεβ 2014, 04:50
Ο δεύτερος δίσκος από το πρώτο λάπτοπ στην υπογραφή μου.
Προς το παρόν δουλεύει αν & έχει μερικά bad sectors, αλλά με τις τιμές που βλέπω τον περιμένω να χαλάσει κάποια στιγμή. Βέβαια τον περιμένω εδώ & ένα χρόνο, σε αντίθεση με τον πρώτο δίσκο που είχε (ίδιος με αυτόν, seagate 500 Gb) & χάλασε εν ψυχρώ από τη μια μέρα στην άλλη & ενώ έδειχνε υγιέστατος στο εργαλείο δίσκων. Στη θέση του έβαλα έναν μεταχειρισμένο hitachi 80 Gb από ένα χαλασμένο λάπτοπ ενός φίλου.
- Κώδικας: Επιλογή όλων
smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST9500325AS
Serial Number: 5VE3CFXS
Firmware Version: 0003SDM1
User Capacity: 500.107.862.016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Thu Feb 27 03:20:49 2014 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 144) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 166632860
3 Spin_Up_Time 0x0003 098 098 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2489
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1
7 Seek_Error_Rate 0x000f 100 253 030 Pre-fail Always - 946413
9 Power_On_Hours 0x0032 088 088 000 Old_age Always - 11108
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always - 2348
184 Unknown_Attribute 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 064 064 000 Old_age Always - 36
188 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 063 043 045 Old_age Always In_the_past 37 (10 199 38 19)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 197
193 Load_Cycle_Count 0x0032 095 095 000 Old_age Always - 10549
194 Temperature_Celsius 0x0022 037 057 000 Old_age Always - 37 (0 13 0 0)
195 Hardware_ECC_Recovered 0x001a 045 043 000 Old_age Always - 166632860
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 1
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
254 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 30 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 30 occurred at disk power-on lifetime: 6888 hours (287 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:27:30.204 READ FPDMA QUEUED
27 00 00 00 00 00 e0 00 00:27:30.203 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:27:30.202 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:27:30.201 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:27:30.201 READ NATIVE MAX ADDRESS EXT
Error 29 occurred at disk power-on lifetime: 6888 hours (287 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:27:27.860 READ FPDMA QUEUED
27 00 00 00 00 00 e0 00 00:27:27.860 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:27:27.858 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:27:27.858 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:27:27.857 READ NATIVE MAX ADDRESS EXT
Error 28 occurred at disk power-on lifetime: 6888 hours (287 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:27:25.548 READ FPDMA QUEUED
27 00 00 00 00 00 e0 00 00:27:25.548 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:27:25.546 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:27:25.546 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:27:25.545 READ NATIVE MAX ADDRESS EXT
Error 27 occurred at disk power-on lifetime: 6888 hours (287 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:27:23.194 READ FPDMA QUEUED
27 00 00 00 00 00 e0 00 00:27:23.193 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:27:23.192 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:27:23.191 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:27:23.191 READ NATIVE MAX ADDRESS EXT
Error 26 occurred at disk power-on lifetime: 6888 hours (287 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:27:18.604 READ FPDMA QUEUED
27 00 00 00 00 00 e0 00 00:27:18.603 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:27:18.602 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:27:18.601 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:27:18.601 READ NATIVE MAX ADDRESS EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 9671 -
# 2 Short offline Completed without error 00% 8933 -
# 3 Short offline Completed without error 00% 8875 -
# 4 Short offline Completed without error 00% 2348 -
# 5 Short offline Completed without error 00% 2348 -
# 6 Extended offline Aborted by host 90% 2347 -
# 7 Short offline Completed without error 00% 2346 -
# 8 Short offline Completed without error 00% 2346 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Προς το παρόν δουλεύει αν & έχει μερικά bad sectors, αλλά με τις τιμές που βλέπω τον περιμένω να χαλάσει κάποια στιγμή. Βέβαια τον περιμένω εδώ & ένα χρόνο, σε αντίθεση με τον πρώτο δίσκο που είχε (ίδιος με αυτόν, seagate 500 Gb) & χάλασε εν ψυχρώ από τη μια μέρα στην άλλη & ενώ έδειχνε υγιέστατος στο εργαλείο δίσκων. Στη θέση του έβαλα έναν μεταχειρισμένο hitachi 80 Gb από ένα χαλασμένο λάπτοπ ενός φίλου.
- Κώδικας: Επιλογή όλων
smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Travelstar 7K100
Device Model: Hitachi HTS721080G9SA00
Serial Number: MPCDN7Y4GXL4SL
Firmware Version: MC4OC10H
User Capacity: 80.026.361.856 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 1
Local Time is: Thu Feb 27 03:37:08 2014 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 45) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always - 0
2 Throughput_Performance 0x0004 100 100 000 Old_age Offline - 173
3 Spin_Up_Time 0x0007 216 216 033 Pre-fail Always - 1
4 Start_Stop_Count 0x0012 099 099 000 Old_age Always - 2189
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000a 100 100 000 Old_age Always - 0
8 Seek_Time_Performance 0x0004 100 100 000 Old_age Offline - 0
9 Power_On_Hours 0x0012 078 078 000 Old_age Always - 9906
10 Spin_Retry_Count 0x0012 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 2189
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 88
193 Load_Cycle_Count 0x0012 087 087 000 Old_age Always - 131033
194 Temperature_Celsius 0x0002 157 157 000 Old_age Always - 35 (Lifetime Min/Max 12/56)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 11
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 7723 -
# 2 Short offline Completed without error 00% 0 -
Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum.
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.