Δημοσιεύτηκε: 10 Μάιος 2014, 11:02
μιας και πετυχα αυτο το θεμα και ανχωθηκα για λιγο.... να φανταστω οι δικοι μου hdd την εζεισαν την ζωη τους??
αλλα δεν καταλαβαινω κατι ακομα ο 320 ειναι σχετικα παλιος οκ ο 500 ειναι σχετικα νεος και διχνει να εχει περισσοτερεσ ωρες
μπορω να κανω reset στα stats? και ρωταω με τη λογικη οτι τα Seek_Error_Rate μπορει να προηλθαν απο κραδασμους ή καποια τυχαια γεγονοτα
αλλα δεν καταλαβαινω κατι ακομα ο 320 ειναι σχετικα παλιος οκ ο 500 ειναι σχετικα νεος και διχνει να εχει περισσοτερεσ ωρες
μπορω να κανω reset στα stats? και ρωταω με τη λογικη οτι τα Seek_Error_Rate μπορει να προηλθαν απο κραδασμους ή καποια τυχαια γεγονοτα
- Κώδικας: Επιλογή όλων
q@q:~$ sudo smartctl --all /dev/sda
[sudo] password for q:
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.10
Device Model: ST3500630AS
Serial Number: 6QG2P5NY
Firmware Version: 3.AAK
User Capacity: 500.106.780.160 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Sat May 10 10:39:08 2014 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 163) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 115 087 006 Pre-fail Always - 87397778
3 Spin_Up_Time 0x0003 094 093 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 765
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 065 049 030 Pre-fail Always - 189123760506
9 Power_On_Hours 0x0032 059 059 000 Old_age Always - 36456
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 759
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 070 041 045 Old_age Always In_the_past 30 (Min/Max 20/30)
194 Temperature_Celsius 0x0022 030 059 000 Old_age Always - 30 (0 16 0 0 0)
195 Hardware_ECC_Recovered 0x001a 077 051 000 Old_age Always - 193687932
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 198 000 Old_age Always - 247
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 776 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 776 occurred at disk power-on lifetime: 36407 hours (1516 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 ee 57 38 ea
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 ff 01 ee 57 38 ea 00 00:55:25.095 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 00 ee 57 38 e0 00 00:55:24.870 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 00 ee 57 38 ea 00 00:55:24.808 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 01 ee 57 38 e0 00 00:55:24.637 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 01 ee 57 38 ea 00 00:55:24.512 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 775 occurred at disk power-on lifetime: 36407 hours (1516 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 ee 57 38 ea
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 ff 01 ee 57 38 ea 00 00:55:25.095 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 00 ee 57 38 e0 00 00:55:24.870 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 00 ee 57 38 ea 00 00:55:24.808 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 01 2f 60 38 e0 00 00:55:24.637 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
29 00 01 2f 60 38 e0 00 00:55:24.512 READ MULTIPLE EXT
Error 774 occurred at disk power-on lifetime: 36334 hours (1513 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 ee 57 38 ea
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 ff 01 ee 57 38 ea 00 01:51:14.815 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 00 ee 57 38 e0 00 01:51:14.752 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 00 ee 57 38 ea 00 01:51:14.581 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 01 ee 57 38 e0 00 01:51:14.456 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 01 ee 57 38 ea 00 01:51:14.389 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 773 occurred at disk power-on lifetime: 36334 hours (1513 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 ee 57 38 ea
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 ff 01 ee 57 38 ea 00 01:51:14.815 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 00 ee 57 38 e0 00 01:51:14.752 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 00 ee 57 38 ea 00 01:51:14.581 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 01 2f 60 38 e0 00 01:51:14.456 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
29 00 01 2f 60 38 e0 00 01:51:14.389 READ MULTIPLE EXT
Error 772 occurred at disk power-on lifetime: 36323 hours (1513 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 ee 57 38 ea
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 ff 01 ee 57 38 ea 00 04:59:54.162 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 00 ee 57 38 e0 00 04:59:49.249 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 00 ee 57 38 ea 00 04:59:49.202 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 01 ee 57 38 e0 00 04:59:49.202 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 01 ee 57 38 ea 00 04:59:49.202 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 36456 -
# 2 Extended offline Aborted by host 90% 36456 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
q@q:~$
- Κώδικας: Επιλογή όλων
q@q:~$ sudo smartctl --all /dev/sdb
[sudo] password for q:
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.10
Device Model: ST3320620AS
Serial Number: 3QF0YR3C
Firmware Version: 3.AAE
User Capacity: 320.071.851.520 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Sat May 10 10:41:54 2014 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 115) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 099 073 006 Pre-fail Always - 1073492
3 Spin_Up_Time 0x0003 096 095 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1087
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 065 060 030 Pre-fail Always - 1113278331953
9 Power_On_Hours 0x0032 065 065 000 Old_age Always - 31438
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1633
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 069 044 045 Old_age Always In_the_past 31 (Min/Max 20/31)
194 Temperature_Celsius 0x0022 031 056 000 Old_age Always - 31 (0 16 0 0 0)
195 Hardware_ECC_Recovered 0x001a 069 047 000 Old_age Always - 179501818
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 2
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 842 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 842 occurred at disk power-on lifetime: 31034 hours (1293 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 6e e2 42 e5
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 ff 01 6e e2 42 e5 00 04:59:58.848 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 00 6e e2 42 e0 00 04:59:58.848 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 00 6e e2 42 e5 00 04:59:58.847 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 01 6e e2 42 e0 00 05:00:06.875 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 01 6e e2 42 e5 00 05:00:06.816 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 841 occurred at disk power-on lifetime: 31034 hours (1293 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 6e e2 42 e5
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 ff 01 6e e2 42 e5 00 04:59:58.848 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 00 6e e2 42 e0 00 04:59:58.848 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 00 6e e2 42 e5 00 04:59:58.847 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 01 af ea 42 e0 00 04:59:58.847 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
29 00 01 af ea 42 e0 00 04:59:58.847 READ MULTIPLE EXT
Error 840 occurred at disk power-on lifetime: 31031 hours (1292 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 6e e2 42 e5
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 ff 01 6e e2 42 e5 00 00:01:18.707 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 00 6e e2 42 e0 00 00:01:18.491 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 00 6e e2 42 e5 00 00:01:18.427 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 01 6e e2 42 e0 00 00:01:18.249 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 01 6e e2 42 e5 00 00:01:18.133 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 839 occurred at disk power-on lifetime: 31031 hours (1292 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 6e e2 42 e5
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 ff 01 6e e2 42 e5 00 00:01:18.707 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 00 6e e2 42 e0 00 00:01:18.491 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 00 6e e2 42 e5 00 00:01:18.427 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 01 af ea 42 e0 00 00:01:18.249 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
29 00 01 af ea 42 e0 00 00:01:18.133 READ MULTIPLE EXT
Error 838 occurred at disk power-on lifetime: 16403 hours (683 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 6e e2 42 e5
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 ff 01 6e e2 42 e5 00 00:07:19.293 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 00 6e e2 42 e0 00 00:07:17.213 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 00 6e e2 42 e5 00 00:07:17.154 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
27 ff 01 6e e2 42 e0 00 00:07:16.938 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
37 ff 01 6e e2 42 e5 00 00:07:16.873 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 31438 -
# 2 Short offline Completed without error 00% 30575 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
q@q:~$