Δημοσιεύτηκε: 26 Μάιος 2014, 08:38
μια μικρή βοήθεια για να σιγουρευτώ οτι οι δίσκοι πάνε για αλλαγή παρακαλω, sda και sdb
- Κώδικας: Επιλογή όλων
sudo smartctl -a /dev/sda
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST3000DM001-9YN166
Serial Number: Z1F15G6S
LU WWN Device Id: 5 000c50 04e4699d2
Firmware Version: CC4B
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon May 26 08:32:54 2014 EEST
==> WARNING: A firmware update for this drive may be available,
see the following Seagate web pages:
http://knowledge.seagate.com/articles/en_US/FAQ/207931en
http://knowledge.seagate.com/articles/en_US/FAQ/223651en
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 584) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 352) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3085) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 116 093 006 Pre-fail Always - 106101152
3 Spin_Up_Time 0x0003 093 093 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 15
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 8
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 143463162
9 Power_On_Hours 0x0032 091 091 000 Old_age Always - 8439
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 15
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 2060
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 0 0
189 High_Fly_Writes 0x003a 098 098 000 Old_age Always - 2
190 Airflow_Temperature_Cel 0x0022 067 052 045 Old_age Always - 33 (Min/Max 32/35)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 9
193 Load_Cycle_Count 0x0032 077 077 000 Old_age Always - 46895
194 Temperature_Celsius 0x0022 033 048 000 Old_age Always - 33 (0 18 0 0 0)
197 Current_Pending_Sector 0x0012 100 001 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 001 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 6924h+51m+41.940s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 278506363319203
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 63036076050996
SMART Error Log Version: 1
ATA Error Count: 2060 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2060 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 6d+23:28:32.109 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 6d+23:28:32.108 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 6d+23:28:32.108 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 6d+23:28:32.108 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 6d+23:28:32.107 IDENTIFY DEVICE
Error 2059 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 6d+23:28:29.233 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 6d+23:28:29.233 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 6d+23:28:29.232 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 6d+23:28:29.232 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 6d+23:28:29.232 IDENTIFY DEVICE
Error 2058 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED
60 00 80 ff ff ff 4f 00 6d+23:28:26.348 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 6d+23:28:26.348 SET FEATURES [Enable SATA feature]
Error 2057 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 6d+23:28:23.456 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 6d+23:28:23.456 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 6d+23:28:23.456 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 6d+23:28:23.456 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 6d+23:28:23.456 SET FEATURES [Set transfer mode]
Error 2056 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 6d+23:28:20.581 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 6d+23:28:20.581 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 6d+23:28:20.581 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 6d+23:28:20.580 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 6d+23:28:20.580 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 6532 -
# 2 Extended offline Completed without error 00% 6502 -
# 3 Extended offline Completed without error 00% 5165 -
# 4 Extended offline Completed without error 00% 5 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
- Κώδικας: Επιλογή όλων
sudo smartctl -a /dev/sdb
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST3000DM001-1CH166
Serial Number: Z1F0Z1FL
LU WWN Device Id: 5 000c50 04dffbbcb
Firmware Version: CC43
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon May 26 08:37:44 2014 EEST
==> WARNING: A firmware update for this drive may be available,
see the following Seagate web pages:
http://knowledge.seagate.com/articles/en_US/FAQ/207931en
http://knowledge.seagate.com/articles/en_US/FAQ/223651en
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 584) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 328) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3085) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 145310616
3 Spin_Up_Time 0x0003 091 091 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 21
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 40
7 Seek_Error_Rate 0x000f 053 051 030 Pre-fail Always - 1898462924882
9 Power_On_Hours 0x0032 087 087 000 Old_age Always - 11931
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 21
183 Runtime_Bad_Block 0x0032 099 099 000 Old_age Always - 1
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 097 097 000 Old_age Always - 3
188 Command_Timeout 0x0032 100 098 000 Old_age Always - 2 2 2
189 High_Fly_Writes 0x003a 028 028 000 Old_age Always - 72
190 Airflow_Temperature_Cel 0x0022 066 055 045 Old_age Always - 34 (Min/Max 33/37)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 19
193 Load_Cycle_Count 0x0032 083 083 000 Old_age Always - 35641
194 Temperature_Celsius 0x0022 034 045 000 Old_age Always - 34 (0 21 0 0 0)
197 Current_Pending_Sector 0x0012 100 032 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 032 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 11912h+29m+01.926s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 116064681029
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 326236248135
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 10025 -
# 2 Extended offline Completed without error 00% 9996 -
# 3 Extended offline Completed without error 00% 9629 -
# 4 Extended offline Completed without error 00% 50 -
# 5 Extended offline Completed without error 00% 6 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.