Δημοσιεύτηκε: 28 Μάιος 2014, 09:20
Για όποιον θέλει να ρίξει μια ματιά, οι τιμές αυξήθηκαν αισθητά μέσα σε 2 ημέρες.
26/5/2014
28/5/2014
Οι δίσκοι είναι του σερβερ και μπορώ να πω να τους αντικαταστήσουν αρκεί να με βοηθήσετε, δηλαδή να τους πω "αυτό κι αυτό", δηλαδή πως να το δικαιολογήσω σε περίπτωση που κάνουν κάποια νάζια
26/5/2014
lepidas έγραψε:
- Κώδικας: Επιλογή όλων
sudo smartctl -a /dev/sda
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST3000DM001-9YN166
Serial Number: Z1F15G6S
LU WWN Device Id: 5 000c50 04e4699d2
Firmware Version: CC4B
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon May 26 08:32:54 2014 EEST
==> WARNING: A firmware update for this drive may be available,
see the following Seagate web pages:
http://knowledge.seagate.com/articles/en_US/FAQ/207931en
http://knowledge.seagate.com/articles/en_US/FAQ/223651en
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 584) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 352) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3085) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 116 093 006 Pre-fail Always - 106101152
3 Spin_Up_Time 0x0003 093 093 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 15
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 8
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 143463162
9 Power_On_Hours 0x0032 091 091 000 Old_age Always - 8439
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 15
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 2060
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 0 0
189 High_Fly_Writes 0x003a 098 098 000 Old_age Always - 2
190 Airflow_Temperature_Cel 0x0022 067 052 045 Old_age Always - 33 (Min/Max 32/35)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 9
193 Load_Cycle_Count 0x0032 077 077 000 Old_age Always - 46895
194 Temperature_Celsius 0x0022 033 048 000 Old_age Always - 33 (0 18 0 0 0)
197 Current_Pending_Sector 0x0012 100 001 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 001 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 6924h+51m+41.940s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 278506363319203
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 63036076050996
SMART Error Log Version: 1
ATA Error Count: 2060 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2060 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 6d+23:28:32.109 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 6d+23:28:32.108 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 6d+23:28:32.108 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 6d+23:28:32.108 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 6d+23:28:32.107 IDENTIFY DEVICE
Error 2059 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 6d+23:28:29.233 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 6d+23:28:29.233 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 6d+23:28:29.232 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 6d+23:28:29.232 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 6d+23:28:29.232 IDENTIFY DEVICE
Error 2058 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED
60 00 80 ff ff ff 4f 00 6d+23:28:26.348 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 6d+23:28:26.348 SET FEATURES [Enable SATA feature]
Error 2057 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 6d+23:28:23.456 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 6d+23:28:23.456 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 6d+23:28:23.456 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 6d+23:28:23.456 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 6d+23:28:23.456 SET FEATURES [Set transfer mode]
Error 2056 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 6d+23:28:20.581 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 6d+23:28:20.581 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 6d+23:28:20.581 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 6d+23:28:20.580 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 6d+23:28:20.580 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 6532 -
# 2 Extended offline Completed without error 00% 6502 -
# 3 Extended offline Completed without error 00% 5165 -
# 4 Extended offline Completed without error 00% 5 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
- Κώδικας: Επιλογή όλων
sudo smartctl -a /dev/sdb
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST3000DM001-1CH166
Serial Number: Z1F0Z1FL
LU WWN Device Id: 5 000c50 04dffbbcb
Firmware Version: CC43
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon May 26 08:37:44 2014 EEST
==> WARNING: A firmware update for this drive may be available,
see the following Seagate web pages:
http://knowledge.seagate.com/articles/en_US/FAQ/207931en
http://knowledge.seagate.com/articles/en_US/FAQ/223651en
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 584) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 328) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3085) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 145310616
3 Spin_Up_Time 0x0003 091 091 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 21
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 40
7 Seek_Error_Rate 0x000f 053 051 030 Pre-fail Always - 1898462924882
9 Power_On_Hours 0x0032 087 087 000 Old_age Always - 11931
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 21
183 Runtime_Bad_Block 0x0032 099 099 000 Old_age Always - 1
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 097 097 000 Old_age Always - 3
188 Command_Timeout 0x0032 100 098 000 Old_age Always - 2 2 2
189 High_Fly_Writes 0x003a 028 028 000 Old_age Always - 72
190 Airflow_Temperature_Cel 0x0022 066 055 045 Old_age Always - 34 (Min/Max 33/37)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 19
193 Load_Cycle_Count 0x0032 083 083 000 Old_age Always - 35641
194 Temperature_Celsius 0x0022 034 045 000 Old_age Always - 34 (0 21 0 0 0)
197 Current_Pending_Sector 0x0012 100 032 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 032 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 11912h+29m+01.926s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 116064681029
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 326236248135
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 10025 -
# 2 Extended offline Completed without error 00% 9996 -
# 3 Extended offline Completed without error 00% 9629 -
# 4 Extended offline Completed without error 00% 50 -
# 5 Extended offline Completed without error 00% 6 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
28/5/2014
- Κώδικας: Επιλογή όλων
sudo smartctl -a /dev/sda
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST3000DM001-9YN166
Serial Number: Z1F15G6S
LU WWN Device Id: 5 000c50 04e4699d2
Firmware Version: CC4B
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed May 28 09:18:51 2014 EEST
==> WARNING: A firmware update for this drive may be available,
see the following Seagate web pages:
http://knowledge.seagate.com/articles/en_US/FAQ/207931en
http://knowledge.seagate.com/articles/en_US/FAQ/223651en
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 584) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 352) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3085) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 093 006 Pre-fail Always - 117991696
3 Spin_Up_Time 0x0003 093 093 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 15
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 8
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 144149703
9 Power_On_Hours 0x0032 091 091 000 Old_age Always - 8488
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 15
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 2060
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 0 0
189 High_Fly_Writes 0x003a 098 098 000 Old_age Always - 2
190 Airflow_Temperature_Cel 0x0022 067 052 045 Old_age Always - 33 (Min/Max 32/35)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 9
193 Load_Cycle_Count 0x0032 077 077 000 Old_age Always - 46895
194 Temperature_Celsius 0x0022 033 048 000 Old_age Always - 33 (0 18 0 0 0)
197 Current_Pending_Sector 0x0012 100 001 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 001 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 6973h+37m+58.250s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 278529293718899
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 63049642357404
SMART Error Log Version: 1
ATA Error Count: 2060 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2060 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 6d+23:28:32.109 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 6d+23:28:32.108 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 6d+23:28:32.108 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 6d+23:28:32.108 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 6d+23:28:32.107 IDENTIFY DEVICE
Error 2059 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 6d+23:28:29.233 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 6d+23:28:29.233 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 6d+23:28:29.232 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 6d+23:28:29.232 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 6d+23:28:29.232 IDENTIFY DEVICE
Error 2058 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED
60 00 80 ff ff ff 4f 00 6d+23:28:26.348 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 6d+23:28:26.348 SET FEATURES [Enable SATA feature]
Error 2057 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 6d+23:28:23.456 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 6d+23:28:23.456 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 6d+23:28:23.456 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 6d+23:28:23.456 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 6d+23:28:23.456 SET FEATURES [Set transfer mode]
Error 2056 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 6d+23:28:20.581 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 6d+23:28:20.581 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 6d+23:28:20.581 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 6d+23:28:20.580 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 6d+23:28:20.580 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 6532 -
# 2 Extended offline Completed without error 00% 6502 -
# 3 Extended offline Completed without error 00% 5165 -
# 4 Extended offline Completed without error 00% 5 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
- Κώδικας: Επιλογή όλων
sudo smartctl -a /dev/sdb
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST3000DM001-1CH166
Serial Number: Z1F0Z1FL
LU WWN Device Id: 5 000c50 04dffbbcb
Firmware Version: CC43
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed May 28 09:19:22 2014 EEST
==> WARNING: A firmware update for this drive may be available,
see the following Seagate web pages:
http://knowledge.seagate.com/articles/en_US/FAQ/207931en
http://knowledge.seagate.com/articles/en_US/FAQ/223651en
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 584) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 328) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3085) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 147374912
3 Spin_Up_Time 0x0003 091 091 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 21
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 40
7 Seek_Error_Rate 0x000f 053 051 030 Pre-fail Always - 1898463545583
9 Power_On_Hours 0x0032 087 087 000 Old_age Always - 11980
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 21
183 Runtime_Bad_Block 0x0032 099 099 000 Old_age Always - 1
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 097 097 000 Old_age Always - 3
188 Command_Timeout 0x0032 100 098 000 Old_age Always - 2 2 2
189 High_Fly_Writes 0x003a 028 028 000 Old_age Always - 72
190 Airflow_Temperature_Cel 0x0022 066 055 045 Old_age Always - 34 (Min/Max 33/37)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 19
193 Load_Cycle_Count 0x0032 083 083 000 Old_age Always - 35641
194 Temperature_Celsius 0x0022 034 045 000 Old_age Always - 34 (0 21 0 0 0)
197 Current_Pending_Sector 0x0012 100 032 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 032 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 11961h+10m+57.745s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 116078149386
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 326236456001
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 10025 -
# 2 Extended offline Completed without error 00% 9996 -
# 3 Extended offline Completed without error 00% 9629 -
# 4 Extended offline Completed without error 00% 50 -
# 5 Extended offline Completed without error 00% 6 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Οι δίσκοι είναι του σερβερ και μπορώ να πω να τους αντικαταστήσουν αρκεί να με βοηθήσετε, δηλαδή να τους πω "αυτό κι αυτό", δηλαδή πως να το δικαιολογήσω σε περίπτωση που κάνουν κάποια νάζια