Δημοσιεύτηκε: 28 Σεπ 2014, 10:10
από astone42
Αυτά είναι τα αποτελέσματα, έχω τρομέρα κολλήματα και στο boot μία τον βλέπει και μία δεν τον βλέπει τον δίσκο. Αλλάζω δίσκο ; (Το memtest86+ για την μνήμη Ram τα δείχνει όλα οκ).
Όταν βλέπει τον δίσκο και κάνει boot από αυτόν μετά από 1-10 λεπτά αρχίζει να μην ανταποκρίνεται και εν τέλει κρασάρει τελείως.
Όταν βλέπει τον δίσκο και κάνει boot από αυτόν μετά από 1-10 λεπτά αρχίζει να μην ανταποκρίνεται και εν τέλει κρασάρει τελείως.
Spoiler: show
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.11
Device Model: ST31500341AS
Serial Number: 9VS3D8HK
LU WWN Device Id: 5 000c50 01a8643e3
Firmware Version: CC1H
User Capacity: 1.500.301.910.016 bytes [1,50 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sun Sep 28 10:09:14 2014 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 609) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 293) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 102 098 006 Pre-fail Always - 9686054
3 Spin_Up_Time 0x0003 100 091 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2298
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 34
7 Seek_Error_Rate 0x000f 087 060 030 Pre-fail Always - 628225163
9 Power_On_Hours 0x0032 077 077 000 Old_age Always - 20928
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 23
12 Power_Cycle_Count 0x0032 098 037 020 Old_age Always - 2353
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 124
188 Command_Timeout 0x0032 100 097 000 Old_age Always - 1135
189 High_Fly_Writes 0x003a 001 001 000 Old_age Always - 1072
190 Airflow_Temperature_Cel 0x0022 064 051 045 Old_age Always - 36 (Min/Max 36/36)
194 Temperature_Celsius 0x0022 036 049 000 Old_age Always - 36 (0 15 0 0 0)
195 Hardware_ECC_Recovered 0x001a 061 029 000 Old_age Always - 9686054
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 465
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 465
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 32963874017703
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2772258090
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 3429467585
SMART Error Log Version: 1
ATA Error Count: 93 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 93 occurred at disk power-on lifetime: 20928 hours (872 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f9 27 63 00 Error: UNC at LBA = 0x006327f9 = 6498297
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f8 27 63 40 00 00:00:04.724 READ DMA EXT
25 00 08 f8 27 63 40 00 00:00:01.980 READ DMA EXT
35 00 02 07 17 88 40 00 00:00:01.979 WRITE DMA EXT
25 00 01 07 17 88 40 00 00:00:01.978 READ DMA EXT
25 00 01 08 17 88 40 00 00:00:01.978 READ DMA EXT
Error 92 occurred at disk power-on lifetime: 20928 hours (872 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f9 27 63 00 Error: UNC at LBA = 0x006327f9 = 6498297
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f8 27 63 40 00 00:00:01.980 READ DMA EXT
35 00 02 07 17 88 40 00 00:00:01.979 WRITE DMA EXT
25 00 01 07 17 88 40 00 00:00:01.978 READ DMA EXT
25 00 01 08 17 88 40 00 00:00:01.978 READ DMA EXT
25 00 02 07 17 88 40 00 00:00:01.971 READ DMA EXT
Error 91 occurred at disk power-on lifetime: 20928 hours (872 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f9 27 63 00 Error: UNC at LBA = 0x006327f9 = 6498297
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f8 27 63 40 00 00:00:04.724 READ DMA EXT
25 00 08 f8 27 63 40 00 00:00:01.997 READ DMA EXT
35 00 02 07 17 88 40 00 00:00:01.996 WRITE DMA EXT
25 00 01 07 17 88 40 00 00:00:01.995 READ DMA EXT
25 00 01 08 17 88 40 00 00:00:01.995 READ DMA EXT
Error 90 occurred at disk power-on lifetime: 20928 hours (872 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f9 27 63 00 Error: UNC at LBA = 0x006327f9 = 6498297
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f8 27 63 40 00 00:00:01.997 READ DMA EXT
35 00 02 07 17 88 40 00 00:00:01.996 WRITE DMA EXT
25 00 01 07 17 88 40 00 00:00:01.995 READ DMA EXT
25 00 01 08 17 88 40 00 00:00:01.995 READ DMA EXT
25 00 02 07 17 88 40 00 00:00:01.988 READ DMA EXT
Error 89 occurred at disk power-on lifetime: 20927 hours (871 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f9 27 63 00 Error: UNC at LBA = 0x006327f9 = 6498297
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f8 27 63 40 00 00:00:04.716 READ DMA EXT
25 00 08 f8 27 63 40 00 00:00:01.989 READ DMA EXT
35 00 02 07 17 88 40 00 00:00:01.988 WRITE DMA EXT
25 00 01 07 17 88 40 00 00:00:01.987 READ DMA EXT
25 00 01 08 17 88 40 00 00:00:01.987 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 20927 6498297
# 2 Short offline Completed: read failure 90% 20927 6498297
# 3 Extended offline Completed: read failure 90% 20927 6498297
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Model Family: Seagate Barracuda 7200.11
Device Model: ST31500341AS
Serial Number: 9VS3D8HK
LU WWN Device Id: 5 000c50 01a8643e3
Firmware Version: CC1H
User Capacity: 1.500.301.910.016 bytes [1,50 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sun Sep 28 10:09:14 2014 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 609) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 293) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 102 098 006 Pre-fail Always - 9686054
3 Spin_Up_Time 0x0003 100 091 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2298
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 34
7 Seek_Error_Rate 0x000f 087 060 030 Pre-fail Always - 628225163
9 Power_On_Hours 0x0032 077 077 000 Old_age Always - 20928
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 23
12 Power_Cycle_Count 0x0032 098 037 020 Old_age Always - 2353
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 124
188 Command_Timeout 0x0032 100 097 000 Old_age Always - 1135
189 High_Fly_Writes 0x003a 001 001 000 Old_age Always - 1072
190 Airflow_Temperature_Cel 0x0022 064 051 045 Old_age Always - 36 (Min/Max 36/36)
194 Temperature_Celsius 0x0022 036 049 000 Old_age Always - 36 (0 15 0 0 0)
195 Hardware_ECC_Recovered 0x001a 061 029 000 Old_age Always - 9686054
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 465
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 465
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 32963874017703
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2772258090
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 3429467585
SMART Error Log Version: 1
ATA Error Count: 93 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 93 occurred at disk power-on lifetime: 20928 hours (872 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f9 27 63 00 Error: UNC at LBA = 0x006327f9 = 6498297
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f8 27 63 40 00 00:00:04.724 READ DMA EXT
25 00 08 f8 27 63 40 00 00:00:01.980 READ DMA EXT
35 00 02 07 17 88 40 00 00:00:01.979 WRITE DMA EXT
25 00 01 07 17 88 40 00 00:00:01.978 READ DMA EXT
25 00 01 08 17 88 40 00 00:00:01.978 READ DMA EXT
Error 92 occurred at disk power-on lifetime: 20928 hours (872 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f9 27 63 00 Error: UNC at LBA = 0x006327f9 = 6498297
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f8 27 63 40 00 00:00:01.980 READ DMA EXT
35 00 02 07 17 88 40 00 00:00:01.979 WRITE DMA EXT
25 00 01 07 17 88 40 00 00:00:01.978 READ DMA EXT
25 00 01 08 17 88 40 00 00:00:01.978 READ DMA EXT
25 00 02 07 17 88 40 00 00:00:01.971 READ DMA EXT
Error 91 occurred at disk power-on lifetime: 20928 hours (872 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f9 27 63 00 Error: UNC at LBA = 0x006327f9 = 6498297
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f8 27 63 40 00 00:00:04.724 READ DMA EXT
25 00 08 f8 27 63 40 00 00:00:01.997 READ DMA EXT
35 00 02 07 17 88 40 00 00:00:01.996 WRITE DMA EXT
25 00 01 07 17 88 40 00 00:00:01.995 READ DMA EXT
25 00 01 08 17 88 40 00 00:00:01.995 READ DMA EXT
Error 90 occurred at disk power-on lifetime: 20928 hours (872 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f9 27 63 00 Error: UNC at LBA = 0x006327f9 = 6498297
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f8 27 63 40 00 00:00:01.997 READ DMA EXT
35 00 02 07 17 88 40 00 00:00:01.996 WRITE DMA EXT
25 00 01 07 17 88 40 00 00:00:01.995 READ DMA EXT
25 00 01 08 17 88 40 00 00:00:01.995 READ DMA EXT
25 00 02 07 17 88 40 00 00:00:01.988 READ DMA EXT
Error 89 occurred at disk power-on lifetime: 20927 hours (871 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f9 27 63 00 Error: UNC at LBA = 0x006327f9 = 6498297
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f8 27 63 40 00 00:00:04.716 READ DMA EXT
25 00 08 f8 27 63 40 00 00:00:01.989 READ DMA EXT
35 00 02 07 17 88 40 00 00:00:01.988 WRITE DMA EXT
25 00 01 07 17 88 40 00 00:00:01.987 READ DMA EXT
25 00 01 08 17 88 40 00 00:00:01.987 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 20927 6498297
# 2 Short offline Completed: read failure 90% 20927 6498297
# 3 Extended offline Completed: read failure 90% 20927 6498297
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.