Δημοσιεύτηκε: 16 Δεκ 2017, 12:50
the_eye έγραψε:Το CRC_Error_Count μπορεί να μην είναι σφάλμα στον δίσκο αλλά στο καλώδιο σύνδεσης.
Ναι, νομιζω τα καλωδια συνδεσεις που εχω δεν ειναι και πολυ οκ.
the_eye έγραψε:Τρέξε τα διαγνωστικά που αναφέρω στο αρχικό θέμα, στο τέλος.
Αυτο το εργαλειο που διχνεις εδω, τo ''GSmartControl'' ειναι;
Αν ειναι αυτο, εκανα ενα Short Self-test.
- Κώδικας: Επιλογή όλων
=== START OF INFORMATION SECTION ===
Model Family: Samsung based SSDs
Device Model: Samsung SSD 850 EVO 250GB
Serial Number: S3R0NF0J830361K
LU WWN Device Id: 5 002538 d4224fe41
Firmware Version: EMT03B6Q
User Capacity: 250.059.350.016 bytes [250 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Dec 16 11:19:15 2017 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 133) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0
9 Power_On_Hours -O--CK 099 099 000 - 573
12 Power_Cycle_Count -O--CK 099 099 000 - 209
177 Wear_Leveling_Count PO--C- 099 099 000 - 3
179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0
181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0
182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0
183 Runtime_Bad_Block PO--C- 100 100 010 - 0
187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0
190 Airflow_Temperature_Cel -O--CK 070 066 000 - 30
195 ECC_Error_Rate -O-RC- 200 200 000 - 0
199 CRC_Error_Count -OSRCK 099 099 000 - 24
235 POR_Recovery_Count -O--C- 099 099 000 - 57
241 Total_LBAs_Written -O--CK 099 099 000 - 1950203228
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 1 Comprehensive SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x13 GPL R/O 1 SATA NCQ Send and Receive log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa1 SL VS 16 Device vendor specific log
0xa5 SL VS 16 Device vendor specific log
0xce SL VS 16 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 573 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
255 0 65535 Read_scanning was never started
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 23 Celsius
Power Cycle Min/Max Temperature: 20/25 Celsius
Lifetime Min/Max Temperature: 17/40 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 10 minutes
Min/Max recommended Temperature: 0/70 Celsius
Min/Max Temperature Limit: 0/70 Celsius
Temperature History Size (Index): 128 (29)
Index Estimated Time Temperature Celsius
30 2017-12-15 14:00 24 *****
31 2017-12-15 14:10 ? -
32 2017-12-15 14:20 18 -
33 2017-12-15 14:30 20 *
34 2017-12-15 14:40 21 **
... ..( 3 skipped). .. **
38 2017-12-15 15:20 21 **
39 2017-12-15 15:30 22 ***
40 2017-12-15 15:40 22 ***
41 2017-12-15 15:50 22 ***
42 2017-12-15 16:00 23 ****
... ..( 9 skipped). .. ****
52 2017-12-15 17:40 23 ****
53 2017-12-15 17:50 27 ********
54 2017-12-15 18:00 24 *****
55 2017-12-15 18:10 26 *******
56 2017-12-15 18:20 26 *******
57 2017-12-15 18:30 28 *********
58 2017-12-15 18:40 24 *****
59 2017-12-15 18:50 23 ****
60 2017-12-15 19:00 23 ****
61 2017-12-15 19:10 23 ****
62 2017-12-15 19:20 22 ***
... ..( 14 skipped). .. ***
77 2017-12-15 21:50 22 ***
78 2017-12-15 22:00 23 ****
79 2017-12-15 22:10 23 ****
80 2017-12-15 22:20 23 ****
81 2017-12-15 22:30 24 *****
82 2017-12-15 22:40 24 *****
83 2017-12-15 22:50 25 ******
... ..( 3 skipped). .. ******
87 2017-12-15 23:30 25 ******
88 2017-12-15 23:40 24 *****
89 2017-12-15 23:50 25 ******
90 2017-12-16 00:00 25 ******
91 2017-12-16 00:10 26 *******
... ..( 7 skipped). .. *******
99 2017-12-16 01:30 26 *******
100 2017-12-16 01:40 25 ******
101 2017-12-16 01:50 26 *******
102 2017-12-16 02:00 26 *******
103 2017-12-16 02:10 26 *******
104 2017-12-16 02:20 25 ******
105 2017-12-16 02:30 26 *******
... ..( 2 skipped). .. *******
108 2017-12-16 03:00 26 *******
109 2017-12-16 03:10 25 ******
... ..( 5 skipped). .. ******
115 2017-12-16 04:10 25 ******
116 2017-12-16 04:20 24 *****
117 2017-12-16 04:30 25 ******
118 2017-12-16 04:40 24 *****
119 2017-12-16 04:50 ? -
120 2017-12-16 05:00 20 *
121 2017-12-16 05:10 21 **
122 2017-12-16 05:20 21 **
123 2017-12-16 05:30 27 ********
124 2017-12-16 05:40 25 ******
125 2017-12-16 05:50 ? -
... ..( 2 skipped). .. -
0 2017-12-16 06:20 ? -
1 2017-12-16 06:30 32 *************
2 2017-12-16 06:40 25 ******
3 2017-12-16 06:50 ? -
4 2017-12-16 07:00 ? -
5 2017-12-16 07:10 26 *******
6 2017-12-16 07:20 25 ******
7 2017-12-16 07:30 25 ******
8 2017-12-16 07:40 27 ********
9 2017-12-16 07:50 25 ******
10 2017-12-16 08:00 25 ******
11 2017-12-16 08:10 25 ******
12 2017-12-16 08:20 ? -
13 2017-12-16 08:30 20 *
14 2017-12-16 08:40 20 *
15 2017-12-16 08:50 21 **
... ..( 2 skipped). .. **
18 2017-12-16 09:20 21 **
19 2017-12-16 09:30 22 ***
20 2017-12-16 09:40 22 ***
21 2017-12-16 09:50 22 ***
22 2017-12-16 10:00 23 ****
23 2017-12-16 10:10 24 *****
24 2017-12-16 10:20 23 ****
... ..( 4 skipped). .. ****
29 2017-12-16 11:10 23 ****
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 19 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 19 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC