Η οθόνη μετά από σβήσιμο δεν ανοίγει όπως πρέπει

[jim04]

Καλημέρα,

Θέλω να ρωτήσω κάτι για το laptop που πήρα.
Όταν κάθομαι στο laptop και για κάποιο λόγο αφησω την οθόνη να κλείσει μετά από 5 λεπτά από αδράνεια, κάποιες φορές αντί να ανοίξει η οθόνη μου εμφανίζει ένα ανοιχτό μαύρ σε ολη τη οθόνη και πρέπει να ανοιγοκλείσω το πορτάκι της οθόνης για να δω.
Τι λέτε ότι μπορεί να συμβαίνει;

[the_eye]

Το laptop είναι αυτό της υπογραφής ;

[jim04]

Ναι

[the_eye]

Για δώσε και το

Κώδικας: Επιλογή όλων

lspci -nn

[jim04]

Μου δίνει αυτό

Κώδικας: Επιλογή όλων

00:02.0 VGA compatible controller [0300]: Intel Corporation Haswell-ULT Integrated Graphics Controller [8086:0a16] (rev 0b)
00:03.0 Audio device [0403]: Intel Corporation Haswell-ULT HD Audio Controller [8086:0a0c] (rev 0b)
00:14.0 USB controller [0c03]: Intel Corporation Lynx Point-LP USB xHCI HC [8086:9c31] (rev 04)
00:16.0 Communication controller [0780]: Intel Corporation Lynx Point-LP HECI #0 [8086:9c3a] (rev 04)
00:1b.0 Audio device [0403]: Intel Corporation Lynx Point-LP HD Audio Controller [8086:9c20] (rev 04)
00:1c.0 PCI bridge [0604]: Intel Corporation Lynx Point-LP PCI Express Root Port 3 [8086:9c14] (rev e4)
00:1c.3 PCI bridge [0604]: Intel Corporation Lynx Point-LP PCI Express Root Port 4 [8086:9c16] (rev e4)
00:1d.0 USB controller [0c03]: Intel Corporation Lynx Point-LP USB EHCI #1 [8086:9c26] (rev 04)
00:1f.0 ISA bridge [0601]: Intel Corporation Lynx Point-LP LPC Controller [8086:9c43] (rev 04)
00:1f.2 SATA controller [0106]: Intel Corporation Lynx Point-LP SATA Controller 1 [AHCI mode] [8086:9c03] (rev 04)
00:1f.3 SMBus [0c05]: Intel Corporation Lynx Point-LP SMBus Controller [8086:9c22] (rev 04)
01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 10)
02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8723BE PCIe Wireless Network Adapter [10ec:b723]


Και κάτι άλλο είχα κλείσει το πορτάκι και ξάπλωσα για το μεσημεριανό ύπνο και η και όταν το άνοιξα δεν άνοιξε η οθόνη

[the_eye]

Πρέπει να έχει να κάνει με τον οδηγό του Haswell δοκίμασε με livecd 14.10 το κάνει ;

[jim04]

Αυτό είναι δύσκολο να γίνει γιατί δεν μου το κάνει συνέχεια. Το κάνει σχεδόν κάθε 2 μέρες. Κάποια άλλη λύση;

[the_eye]

Όταν το κάνει ξανά. Αφού ανοίξει δώσε μας το αποτέλεσμα της dmesg

[jim04]

Είχα αφήσει την οθόνη κλειστή για κανά 2ωρο, δηλαδή το laptop ήταν stand by. Πήγα να την ανοίξω και ενω το ανεμιστηράκι άρχισε να ακούγεται η οθόνη δεν άνοιξε. Σύνδεσα μία άλλη όθόνη που έχω αλλά ούτε και αυτή άνιγε.Πάτησα ο κουμπί εκκίνησης παρατεταμένα για να κλείσει άνοιξε και έδωσα την εντολή dmesg και πήρα πίσω αυτό:

Κώδικας: Επιλογή όλων

[ 0.222474] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.222507] pnp 00:04: Plug and Play ACPI device, IDs ETD0624 ETD0000 PNP0f13 (active)
[ 0.222666] system 00:05: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.222669] system 00:05: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.222672] system 00:05: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.222674] system 00:05: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.222676] system 00:05: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.222678] system 00:05: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.222680] system 00:05: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.222683] system 00:05: [mem 0xff000000-0xffffffff] could not be reserved
[ 0.222685] system 00:05: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.222687] system 00:05: [mem 0xafa20000-0xafa20fff] has been reserved
[ 0.222689] system 00:05: [mem 0xafa10000-0xafa1ffff] has been reserved
[ 0.222692] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.223006] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.223517] pnp: PnP ACPI: found 7 devices
[ 0.223519] ACPI: bus type PNP unregistered
[ 0.230074] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.230078] pci 0000:00:1c.0: bridge window [io 0x4000-0x4fff]
[ 0.230084] pci 0000:00:1c.0: bridge window [mem 0xc0500000-0xc05fffff]
[ 0.230092] pci 0000:00:1c.3: PCI bridge to [bus 02]
[ 0.230095] pci 0000:00:1c.3: bridge window [io 0x3000-0x3fff]
[ 0.230100] pci 0000:00:1c.3: bridge window [mem 0xc0400000-0xc04fffff]
[ 0.230108] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.230111] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.230113] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.230115] pci_bus 0000:00: resource 7 [mem 0xafa00000-0xfeafffff]
[ 0.230117] pci_bus 0000:01: resource 0 [io 0x4000-0x4fff]
[ 0.230119] pci_bus 0000:01: resource 1 [mem 0xc0500000-0xc05fffff]
[ 0.230121] pci_bus 0000:02: resource 0 [io 0x3000-0x3fff]
[ 0.230122] pci_bus 0000:02: resource 1 [mem 0xc0400000-0xc04fffff]
[ 0.230157] NET: Registered protocol family 2
[ 0.230395] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.230487] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.230586] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.230607] TCP: reno registered
[ 0.230615] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.230636] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.230698] NET: Registered protocol family 1
[ 0.230716] pci 0000:00:02.0: Video device with shadowed ROM
[ 0.246861] PCI: CLS 64 bytes, default 64
[ 0.246929] Trying to unpack rootfs image as initramfs...
[ 0.665413] Freeing initrd memory: 18992K (ffff880035ad8000 - ffff880036d64000)
[ 0.665450] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.665453] software IO TLB [mem 0xa6abf000-0xaaabf000] (64MB) mapped at [ffff8800a6abf000-ffff8800aaabefff]
[ 0.665512] Simple Boot Flag at 0x44 set to 0x1
[ 0.665712] RAPL PMU detected, hw unit 2^-14 Joules, API unit is 2^-32 Joules, 4 fixed counters 655360 ms ovfl timer
[ 0.665770] microcode: CPU0 sig=0x40651, pf=0x40, revision=0x1c
[ 0.665777] microcode: CPU1 sig=0x40651, pf=0x40, revision=0x1c
[ 0.665785] microcode: CPU2 sig=0x40651, pf=0x40, revision=0x1c
[ 0.665793] microcode: CPU3 sig=0x40651, pf=0x40, revision=0x1c
[ 0.665853] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 0.665883] Scanning for low memory corruption every 60 seconds
[ 0.666339] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.666374] Initialise system trusted keyring
[ 0.666408] audit: initializing netlink subsys (disabled)
[ 0.666429] audit: type=2000 audit(1429321333.660:1): initialized
[ 0.666853] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.668737] zpool: loaded
[ 0.668742] zbud: loaded
[ 0.668949] VFS: Disk quotas dquot_6.5.2
[ 0.668994] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.669559] fuse init (API version 7.23)
[ 0.669669] msgmni has been set to 7693
[ 0.669746] Key type big_key registered
[ 0.670160] Key type asymmetric registered
[ 0.670164] Asymmetric key parser 'x509' registered
[ 0.670210] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.670266] io scheduler noop registered
[ 0.670269] io scheduler deadline registered (default)
[ 0.670329] io scheduler cfq registered
[ 0.670578] pcieport 0000:00:1c.0: irq 56 for MSI/MSI-X
[ 0.670751] pcieport 0000:00:1c.3: irq 57 for MSI/MSI-X
[ 0.670846] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
[ 0.670848] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 0.670852] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
[ 0.670869] pcieport 0000:00:1c.3: Signaling PME through PCIe PME interrupt
[ 0.670871] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[ 0.670875] pcie_pme 0000:00:1c.3:pcie01: service driver pcie_pme loaded
[ 0.670897] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.670916] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.670975] vesafb: mode is 1366x768x32, linelength=5504, pages=0
[ 0.670976] vesafb: scrolling: redraw
[ 0.670978] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.670997] vesafb: framebuffer at 0xb0000000, mapped to 0xffffc90010800000, using 4160k, total 4160k
[ 0.671112] Console: switching to colour frame buffer device 170x48
[ 0.671130] fb0: VESA VGA frame buffer device
[ 0.671162] intel_idle: MWAIT substates: 0x11142120
[ 0.671164] intel_idle: v0.4 model 0x45
[ 0.671165] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.672498] ACPI: AC Adapter [ADP0] (on-line)
[ 0.672616] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[ 0.672647] ACPI: Lid Switch [LID0]
[ 0.672700] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 0.672704] ACPI: Power Button [PWRB]
[ 0.672745] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 0.672748] ACPI: Power Button [PWRF]
[ 0.673094] GHES: HEST is not enabled!
[ 0.673204] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 0.673626] ACPI: Battery Slot [BAT0] (battery absent)
[ 0.675053] Linux agpgart interface v0.103
[ 0.676481] brd: module loaded
[ 0.677176] loop: module loaded
[ 0.677427] libphy: Fixed MDIO Bus: probed
[ 0.677432] tun: Universal TUN/TAP device driver, 1.6
[ 0.677434] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.677480] PPP generic driver version 2.4.2
[ 0.677534] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.677541] ehci-pci: EHCI PCI platform driver
[ 0.677668] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 0.677675] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 0.677688] ehci-pci 0000:00:1d.0: debug port 2
[ 0.681591] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 0.681607] ehci-pci 0000:00:1d.0: irq 23, io mem 0xc061c000
[ 0.691112] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 0.691161] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.691163] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.691165] usb usb1: Product: EHCI Host Controller
[ 0.691167] usb usb1: Manufacturer: Linux 3.16.0-34-generic ehci_hcd
[ 0.691169] usb usb1: SerialNumber: 0000:00:1d.0
[ 0.691406] hub 1-0:1.0: USB hub found
[ 0.691417] hub 1-0:1.0: 2 ports detected
[ 0.691567] ehci-platform: EHCI generic platform driver
[ 0.691581] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.691589] ohci-pci: OHCI PCI platform driver
[ 0.691603] ohci-platform: OHCI generic platform driver
[ 0.691614] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.691753] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 0.691759] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 0.691839] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 0.691857] xhci_hcd 0000:00:14.0: irq 58 for MSI/MSI-X
[ 0.691917] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.691919] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.691921] usb usb2: Product: xHCI Host Controller
[ 0.691923] usb usb2: Manufacturer: Linux 3.16.0-34-generic xhci_hcd
[ 0.691925] usb usb2: SerialNumber: 0000:00:14.0
[ 0.692157] hub 2-0:1.0: USB hub found
[ 0.692171] hub 2-0:1.0: 9 ports detected
[ 0.694564] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 0.694568] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[ 0.694604] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003
[ 0.694607] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.694608] usb usb3: Product: xHCI Host Controller
[ 0.694610] usb usb3: Manufacturer: Linux 3.16.0-34-generic xhci_hcd
[ 0.694612] usb usb3: SerialNumber: 0000:00:14.0
[ 0.694846] hub 3-0:1.0: USB hub found
[ 0.694856] hub 3-0:1.0: 4 ports detected
[ 0.695294] usb: failed to peer usb3-port2 and usb2-port2 by location (usb3-port2:none) (usb2-port2:usb3-port1)
[ 0.695298] usb usb3-port2: failed to peer to usb2-port2 (-16)
[ 0.695299] usb: port power management may be unreliable
[ 0.695775] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.710444] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.710450] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.710796] mousedev: PS/2 mouse device common for all mice
[ 0.711197] rtc_cmos 00:01: RTC can wake from S4
[ 0.711366] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[ 0.711396] rtc_cmos 00:01: alarms up to one month, 242 bytes nvram, hpet irqs
[ 0.711480] device-mapper: uevent: version 1.0.3
[ 0.711573] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[ 0.711591] Intel P-state driver initializing.
[ 0.711602] Intel pstate controlling: cpu 0
[ 0.711637] Intel pstate controlling: cpu 1
[ 0.711686] Intel pstate controlling: cpu 2
[ 0.711710] Intel pstate controlling: cpu 3
[ 0.711736] Consider also installing thermald for improved thermal control.
[ 0.711742] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.711854] TCP: cubic registered
[ 0.711984] NET: Registered protocol family 10
[ 0.712212] NET: Registered protocol family 17
[ 0.712225] Key type dns_resolver registered
[ 0.712621] Loading compiled-in X.509 certificates
[ 0.713597] Loaded X.509 cert 'Magrathea: Glacier signing key: 80211484dcda0806053931b7eeaade22ea7ec262'
[ 0.713615] registered taskstats version 1
[ 0.715302] Key type trusted registered
[ 0.717680] Key type encrypted registered
[ 0.717687] AppArmor: AppArmor sha1 policy hashing enabled
[ 0.717702] ima: No TPM chip found, activating TPM-bypass!
[ 0.717714] evm: HMAC attrs: 0x1
[ 0.718023] Magic number: 11:127:711
[ 0.718137] rtc_cmos 00:01: setting system clock to 2015-04-18 01:42:14 UTC (1429321334)
[ 0.718195] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.718197] EDD information not available.
[ 0.718262] PM: Hibernation image not present or could not be loaded.
[ 0.718987] Freeing unused kernel memory: 1352K (ffffffff81d1c000 - ffffffff81e6e000)
[ 0.718988] Write protecting the kernel read-only data: 12288k
[ 0.719062] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 0.720317] Freeing unused kernel memory: 560K (ffff880001774000 - ffff880001800000)
[ 0.721278] Freeing unused kernel memory: 500K (ffff880001b83000 - ffff880001c00000)
[ 0.732521] systemd-udevd[122]: starting version 204
[ 0.743650] sdhci: Secure Digital Host Controller Interface driver
[ 0.743654] sdhci: Copyright(c) Pierre Ossman
[ 0.757357] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 0.757365] r8169 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 0.758456] ahci 0000:00:1f.2: version 3.0
[ 0.758554] ahci 0000:00:1f.2: irq 59 for MSI/MSI-X
[ 0.758569] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[ 0.763620] r8169 0000:01:00.0: irq 60 for MSI/MSI-X
[ 0.763826] r8169 0000:01:00.0 eth0: RTL8168g/8111g at 0xffffc9000001a000, 68:f7:28:3b:10:4a, XID 10900880 IRQ 60
[ 0.763829] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 0.771195] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0xf impl SATA mode
[ 0.771199] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo only pio slum part sxs deso sadm sds apst
[ 0.771716] scsi0 : ahci
[ 0.771906] scsi1 : ahci
[ 0.772198] scsi2 : ahci
[ 0.772373] scsi3 : ahci
[ 0.772421] ata1: SATA max UDMA/133 abar m2048@0xc061b000 port 0xc061b100 irq 59
[ 0.772423] ata2: SATA max UDMA/133 abar m2048@0xc061b000 port 0xc061b180 irq 59
[ 0.772424] ata3: SATA max UDMA/133 abar m2048@0xc061b000 port 0xc061b200 irq 59
[ 0.772426] ata4: SATA max UDMA/133 abar m2048@0xc061b000 port 0xc061b280 irq 59
[ 1.003481] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 1.091496] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.097764] ata1.00: ATA-8: ST1000LM024 HN-M101MBB, 2BA30001, max UDMA/100
[ 1.097768] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 1.104105] ata1.00: configured for UDMA/100
[ 1.104248] scsi 0:0:0:0: Direct-Access ATA ST1000LM024 HN-M 0001 PQ: 0 ANSI: 5
[ 1.104636] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 1.104641] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 1.104680] sd 0:0:0:0: [sda] Write Protect is off
[ 1.104684] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.104689] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.104703] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.135989] usb 1-1: New USB device found, idVendor=8087, idProduct=8000
[ 1.135994] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.136217] hub 1-1:1.0: USB hub found
[ 1.136274] hub 1-1:1.0: 8 ports detected
[ 1.156614] sda: sda1 sda2 < sda5 >
[ 1.156959] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.303728] usb 2-3: new low-speed USB device number 2 using xhci_hcd
[ 1.371931] psmouse serio1: elantech: assuming hardware version 4 (with firmware version 0x594f03)
[ 1.386717] psmouse serio1: elantech: Synaptics capabilities query result 0x70, 0x15, 0x0a.
[ 1.423766] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.429076] ata2.00: ATAPI: PLDS DVD-RW DA8A5SH, RL61, max UDMA/100
[ 1.430042] ata2.00: configured for UDMA/100
[ 1.434958] usb 2-3: New USB device found, idVendor=045e, idProduct=0797
[ 1.434962] usb 2-3: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 1.434965] usb 2-3: Product: USB Optical Mouse
[ 1.435158] usb 2-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 1.438544] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.441525] usbcore: registered new interface driver usbhid
[ 1.441527] usbhid: USB HID core driver
[ 1.442381] scsi 1:0:0:0: CD-ROM PLDS DVD-RW DA8A5SH RL61 PQ: 0 ANSI: 5
[ 1.443094] input: USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb2/2-3/2-3:1.0/0003:045E:0797.0001/input/input6
[ 1.443193] hid-generic 0003:045E:0797.0001: input,hidraw0: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:14.0-3/input0
[ 1.468789] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.468793] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.469031] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.469130] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 1.470983] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input5
[ 1.599969] usb 2-4: new high-speed USB device number 3 using xhci_hcd
[ 1.663950] tsc: Refined TSC clocksource calibration: 2394.456 MHz
[ 1.728428] usb 2-4: New USB device found, idVendor=0bda, idProduct=0129
[ 1.728432] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.728435] usb 2-4: Product: USB2.0-CRW
[ 1.728436] usb 2-4: Manufacturer: Generic
[ 1.728438] usb 2-4: SerialNumber: 20100201396000000
[ 1.732308] usbcore: registered new interface driver rtsx_usb
[ 1.788055] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.896207] usb 2-6: new high-speed USB device number 4 using xhci_hcd
[ 2.089701] usb 2-6: New USB device found, idVendor=5986, idProduct=0652
[ 2.089705] usb 2-6: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 2.089707] usb 2-6: Product: Lenovo EasyCamera
[ 2.089709] usb 2-6: Manufacturer: Generic
[ 2.089711] usb 2-6: SerialNumber: 200901010001
[ 2.108314] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.208395] usb 2-7: new full-speed USB device number 5 using xhci_hcd
[ 2.336675] usb 2-7: No LPM exit latency info found, disabling LPM.
[ 2.337604] usb 2-7: New USB device found, idVendor=0bda, idProduct=b728
[ 2.337608] usb 2-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.337610] usb 2-7: Product: Bluetooth Radio
[ 2.337612] usb 2-7: Manufacturer: Realtek
[ 2.337613] usb 2-7: SerialNumber: 00e04c000001
[ 2.346187] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[ 2.346189] EXT4-fs (sda1): write access will be enabled during recovery
[ 2.664771] Switched to clocksource tsc
[ 4.464263] random: nonblocking pool is initialized
[ 4.476122] EXT4-fs (sda1): orphan cleanup on readonly fs
[ 4.476370] EXT4-fs (sda1): 20 orphan inodes deleted
[ 4.476371] EXT4-fs (sda1): recovery complete
[ 4.786449] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 12.662759] Adding 4086780k swap on /dev/sda5. Priority:-1 extents:1 across:4086780k FS
[ 13.279598] systemd-udevd[308]: starting version 204
[ 13.409893] lp: driver loaded but no devices found
[ 13.415891] ppdev: user-space parallel port driver
[ 13.470551] input: Ideapad extra buttons as /devices/pci0000:00/0000:00:1f.0/PNP0C09:00/VPC2004:00/input/input7
[ 13.484822] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 13.486685] mei_me 0000:00:16.0: irq 61 for MSI/MSI-X
[ 13.491503] [drm] Initialized drm 1.1.0 20060810
[ 13.503491] Bluetooth: Core ver 2.19
[ 13.503516] NET: Registered protocol family 31
[ 13.503517] Bluetooth: HCI device and connection manager initialized
[ 13.503525] Bluetooth: HCI socket layer initialized
[ 13.503528] Bluetooth: L2CAP socket layer initialized
[ 13.503536] Bluetooth: SCO socket layer initialized
[ 13.513770] cfg80211: Calling CRDA to update world regulatory domain
[ 13.531892] snd_hda_intel 0000:00:1b.0: irq 62 for MSI/MSI-X
[ 13.532217] [drm] Memory usable by graphics device = 2048M
[ 13.532221] checking generic (b0000000 410000) vs hw (b0000000 10000000)
[ 13.532223] fb: switching to inteldrmfb from VESA VGA
[ 13.532248] Console: switching to colour dummy device 80x25
[ 13.532317] [drm] Replacing VGA console driver
[ 13.542956] usbcore: registered new interface driver btusb
[ 13.544017] sound hdaudioC1D0: CX20751/2: BIOS auto-probing.
[ 13.544243] sound hdaudioC1D0: autoconfig: line_outs=1 (0x17/0x0/0x0/0x0/0x0) type:speaker
[ 13.544245] sound hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 13.544247] sound hdaudioC1D0: hp_outs=1 (0x16/0x0/0x0/0x0/0x0)
[ 13.544248] sound hdaudioC1D0: mono: mono_out=0x0
[ 13.544249] sound hdaudioC1D0: inputs:
[ 13.544250] sound hdaudioC1D0: Internal Mic=0x1a
[ 13.544252] sound hdaudioC1D0: Mic=0x19
[ 13.544955] sound hdaudioC1D0: Enable sync_write for stable communication
[ 13.548134] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input8
[ 13.548228] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input9
[ 13.567283] i915 0000:00:02.0: irq 63 for MSI/MSI-X
[ 13.567295] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 13.567297] [drm] Driver supports precise vblank timestamp query.
[ 13.567327] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 13.567982] rtl8723be: Using firmware rtlwifi/rtl8723befw.bin
[ 13.577274] AVX2 version of gcm_enc/dec engaged.
[ 13.608683] kvm: disabled by bios
[ 13.618440] intel_rapl: Found RAPL domain package
[ 13.618445] intel_rapl: Found RAPL domain core
[ 13.618447] intel_rapl: Found RAPL domain uncore
[ 13.618449] intel_rapl: Found RAPL domain dram
[ 13.642881] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 13.643137] rtlwifi: wireless switch is on
[ 13.664641] [drm] VBT doesn't support DRRS
[ 13.695530] fbcon: inteldrmfb (fb0) is primary device
[ 13.695598] Console: switching to colour frame buffer device 170x48
[ 13.695621] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 13.695623] i915 0000:00:02.0: registered panic notifier
[ 13.735097] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 13.735181] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input10
[ 13.735260] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 13.735704] snd_hda_intel 0000:00:03.0: irq 64 for MSI/MSI-X
[ 13.751321] input: HDA Intel HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input11
[ 13.751444] input: HDA Intel HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input12
[ 13.751496] input: HDA Intel HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input13
[ 13.928701] media: Linux media interface: v0.10
[ 13.932934] Linux video capture interface: v2.00
[ 13.940904] uvcvideo: Found UVC 1.00 device Lenovo EasyCamera (5986:0652)
[ 13.949625] input: Lenovo EasyCamera as /devices/pci0000:00/0000:00:14.0/usb2/2-6/2-6:1.0/input/input14
[ 13.949709] usbcore: registered new interface driver uvcvideo
[ 13.949711] USB Video Class driver (1.1.1)
[ 14.121507] audit: type=1400 audit(1429310547.885:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=447 comm="apparmor_parser"
[ 14.121513] audit: type=1400 audit(1429310547.885:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=447 comm="apparmor_parser"
[ 14.121517] audit: type=1400 audit(1429310547.885:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=447 comm="apparmor_parser"
[ 14.121841] audit: type=1400 audit(1429310547.885:5): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=449 comm="apparmor_parser"
[ 14.121850] audit: type=1400 audit(1429310547.885:6): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=449 comm="apparmor_parser"
[ 14.121855] audit: type=1400 audit(1429310547.885:7): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=449 comm="apparmor_parser"
[ 14.121865] audit: type=1400 audit(1429310547.885:8): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=459 comm="apparmor_parser"
[ 14.121872] audit: type=1400 audit(1429310547.885:9): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=459 comm="apparmor_parser"
[ 14.121878] audit: type=1400 audit(1429310547.885:10): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=459 comm="apparmor_parser"
[ 14.121884] audit: type=1400 audit(1429310547.885:11): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=447 comm="apparmor_parser"
[ 14.335228] cfg80211: World regulatory domain updated:
[ 14.335233] cfg80211: DFS Master region: unset
[ 14.335234] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 14.335237] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[ 14.335240] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[ 14.335242] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm), (N/A)
[ 14.335244] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[ 14.335246] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[ 14.830700] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[ 15.959990] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 16.460640] init: failsafe main process (680) killed by TERM signal
[ 17.144596] Bluetooth: RFCOMM TTY layer initialized
[ 17.144605] Bluetooth: RFCOMM socket layer initialized
[ 17.144609] Bluetooth: RFCOMM ver 1.11
[ 17.251998] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 17.252001] Bluetooth: BNEP filters: protocol multicast
[ 17.252008] Bluetooth: BNEP socket layer initialized
[ 17.607541] init: cups main process (792) killed by HUP signal
[ 17.607549] init: cups main process ended, respawning
[ 18.687762] r8169 0000:01:00.0 eth0: link down
[ 18.687807] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.163091] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 19.174297] audit_printk_skb: 78 callbacks suppressed
[ 19.174303] audit: type=1400 audit(1429310552.937:38): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="pxgsettings" pid=879 comm="apparmor_parser"
[ 19.174313] audit: type=1400 audit(1429310552.937:39): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="sanitized_helper" pid=879 comm="apparmor_parser"
[ 19.174318] audit: type=1400 audit(1429310552.937:40): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/telepathy/telepathy-ofono" pid=879 comm="apparmor_parser"
[ 19.174420] audit: type=1400 audit(1429310552.937:41): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/evince" pid=877 comm="apparmor_parser"
[ 19.174429] audit: type=1400 audit(1429310552.937:42): apparmor="STATUS" operation="profile_load" profile="unconfined" name="sanitized_helper" pid=877 comm="apparmor_parser"
[ 19.174438] audit: type=1400 audit(1429310552.937:43): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/evince-previewer" pid=877 comm="apparmor_parser"
[ 19.174445] audit: type=1400 audit(1429310552.937:44): apparmor="STATUS" operation="profile_load" profile="unconfined" name="sanitized_helper" pid=877 comm="apparmor_parser"
[ 19.174452] audit: type=1400 audit(1429310552.937:45): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/evince-thumbnailer" pid=877 comm="apparmor_parser"
[ 19.174460] audit: type=1400 audit(1429310552.937:46): apparmor="STATUS" operation="profile_load" profile="unconfined" name="sanitized_helper" pid=877 comm="apparmor_parser"
[ 19.175607] audit: type=1400 audit(1429310552.937:47): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="pxgsettings" pid=879 comm="apparmor_parser"
[ 20.139476] wlan0: authenticate with a4:7e:39:c6:64:78
[ 20.149613] wlan0: send auth to a4:7e:39:c6:64:78 (try 1/3)
[ 20.151117] wlan0: authenticated
[ 20.154862] wlan0: associate with a4:7e:39:c6:64:78 (try 1/3)
[ 20.158486] wlan0: RX AssocResp from a4:7e:39:c6:64:78 (capab=0x411 status=0 aid=1)
[ 20.158543] wlan0: associated
[ 20.158553] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 29.328050] init: plymouth-upstart-bridge main process ended, respawning
[ 29.360249] init: plymouth-upstart-bridge main process ended, respawning
[ 47.788745] audit_printk_skb: 78 callbacks suppressed
[ 47.788748] audit: type=1400 audit(1429310580.474:74): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=2406 comm="apparmor_parser"
[ 47.788754] audit: type=1400 audit(1429310580.474:75): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2406 comm="apparmor_parser"
[ 47.789070] audit: type=1400 audit(1429310580.474:76): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2406 comm="apparmor_parser"


Δεν νομίζω ότι μου τα δείχνει όλα.

Κάτι άλλο που παρατήρησα είναι ότι παλότερα με το κουμπί f6 μπορούσα να κλείσω την οθόνη ενώ τώρα δεν κλείνει.

[the_eye]

Αυτό δεν δείχνει τίποτα γιατί έκλεισες το υπολογιστή.