ΠΡΟΒΛΗΜΑ ΜΕ TP LINK TL-WN822N  Το θέμα επιλύθηκε

...κάρτες δικτύου, modems, προβλήματα internet
Κανόνες Δ. Συζήτησης
Για την ευκολότερη επίλυση του προβλήματός σας.
Καλό είναι να δημοσιεύσετε τα αποτελέσματα των εντολών στο τερματικό :
lspci -nn
lsusb
rfkill list

ΠΡΟΒΛΗΜΑ ΜΕ TP LINK TL-WN822N

Δημοσίευσηαπό dentaltech_13 » 26 Σεπ 2016, 00:43

δοκιμασα να συνδεσω το tl wn822n σε ενα παλιο netbook 32bit 1g ram με lubuntu 16 για να εχω μεγαλυτερη εμβελεια αλλα δεν το αναγνωριζει δεν αναβει το led της συσκευης γενικα δεν κανει τιποτα.η συσκευη δουλευει κανονικα σε windows στο ιδιο netbook(dualboot).μπηκα στο σαιτ της tplink και δειχνει οτι υποστηριζει σιγουρα πιο παλιους κερνελ,τοτε δεν ειχαν βγει οι καινουριοι και λογικα δεν εχουν ανανεωσει το σαιτ τους.
ετρεξα τις παρακατω εντολες και μου εβγαλαν τα εξης αποτελεσματα:

dmesg | tail -n 30
Κώδικας: Επιλογή όλων
[  112.048398] wlan0: send auth to 58:98:35:8c:54:c5 (try 1/3)

[  112.061708] wlan0: authenticated

[  112.065178] wlan0: associate with 58:98:35:8c:54:c5 (try 1/3)

[  112.067766] wlan0: RX AssocResp from 58:98:35:8c:54:c5 (capab=0x411 status=0 aid=5)

[  112.067890] wlan0: associated

[  116.648178] usb 1-2: new high-speed USB device number 3 using ehci-pci

[  116.781333] usb 1-2: New USB device found, idVendor=2357, idProduct=0108

[  116.781352] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3

[  116.781365] usb 1-2: Product: 802.11n NIC

[  116.781377] usb 1-2: Manufacturer: Realtek

[  116.781388] usb 1-2: SerialNumber: 00e04c000001

[  170.610636] cfg80211: World regulatory domain updated:

[  170.610646] cfg80211:  DFS Master region: unset

[  170.610650] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)

[  170.610658] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)

[  170.610664] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)

[  170.610669] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)

[  170.610676] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)

[  170.610683] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)

[  170.610689] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)

[  170.610694] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)

[  170.610700] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)

[  177.108936] wlan0: authenticate with 58:98:35:8c:54:c5

[  177.128236] wlan0: send auth to 58:98:35:8c:54:c5 (try 1/3)

[  177.129708] wlan0: authenticated

[  177.136107] wlan0: associate with 58:98:35:8c:54:c5 (try 1/3)

[  177.138502] wlan0: RX AssocResp from 58:98:35:8c:54:c5 (capab=0x411 status=0 aid=5)

[  177.138617] wlan0: associated

[  187.628126] perf interrupt took too long (2511 > 2500), lowering kernel.perf_event_max_sample_rate to 50000

[  197.512115] ieee80211 phy0: rt2x00queue_flush_queue: Warning - Queue 2 failed to flush

lsusb
Bus 001 Device 003: ID 2357:0108 

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub


lsusb

Κώδικας: Επιλογή όλων
Bus 001 Device 003: ID 2357:0108 

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub


δεν ξερω τι να κανω
Τελευταία επεξεργασία από Learner και 26 Σεπ 2016, 19:00, έχει επεξεργασθεί 1 φορά/ες συνολικά
Αιτία: Code Tags
dentaltech_13
babeTUX
babeTUX
 
Δημοσιεύσεις: 5
Εγγραφή: 25 Σεπ 2016, 23:55
Εκτύπωση

Re: ΠΡΟΒΛΗΜΑ ΜΕ TP LINK TL-WN822N

Δημοσίευσηαπό Learner » 26 Σεπ 2016, 20:07

Αποσύνδεσε το USB και φρόντισε να έχεις σύνδεση στο Internet (πχ από τη wireless κάρτα του netbook).

Έπειτα τρέξε τις παρακάτω εντολές μια-μια (copy-paste στο τερματικό σου)
Κώδικας: Επιλογή όλων
sudo apt-get update
sudo apt-get install git dkms
git clone https://github.com/abperiasamy/rtl8812AU_8821AU_linux.git
sudo dkms add ./rtl8812AU_8821AU_linux
sudo dkms install -m 8812au -v 1.0


Εάν οι παραπάνω εντολές τελειώσουν χωρίς errors, σύνδεσε το USB και δες αν λειτουργεί, πλέον.

Source

About Me
Xenial Xerus MuQSS Linux kernel
NickT@Ubuntu

Spoiler: show
1. Ubuntu Xenial (MATE), Arch Linux (GNOME)
2. Intel Core i3 CPU M 380 2.53GHz ‖ RAM 6GB ‖ Acer Aspire 5733
3. Intel Integrated Graphics [8086:0046] {i915}
4. wlan0: Atheros Inc. AR9485 Wireless Network Adapter [168c:0032] (rev 01)
Άβαταρ μέλους
Learner
Συντονιστής
Συντονιστής
 
Δημοσιεύσεις: 9711
Εγγραφή: 08 Νοέμ 2010, 21:24
Τοποθεσία: Αθήνα
Launchpad: NickThom
IRC: NikTh
Εκτύπωση

Re: ΠΡΟΒΛΗΜΑ ΜΕ TP LINK TL-WN822N

Δημοσίευσηαπό dentaltech_13 » 27 Σεπ 2016, 00:13

τα εκανα αλλα παλι τιποτα δεν λειτουργει. τα παρακατω ειναι απο τα τελευταια αποτελεσματα.δεν εβγαλε error


Κώδικας: Επιλογή όλων
Kernel preparation unnecessary for this kernel.  Skipping...

Building module:
cleaning build area.....
'make' KVER=4.4.0-36-generic............................................................................
cleaning build area....

DKMS: build completed.

8812au.ko:
Running module version sanity check.
- Original module
   - No original module exists within this kernel
- Installation
   - Installing to /lib/modules/4.4.0-36-generic/updates/dkms/

depmod............

DKMS: install completed.


μετα εκανα παλι την ιδια διαδικασια γιατι δεν ειχα κανει copy την πρωτη φορα και μου εμφανιζει ενα error

Κώδικας: Επιλογή όλων
~$ sudo dkms add ./rtl8812AU_8821AU_linux
Error! DKMS tree already contains: 8812au-1.0
You cannot add the same module/version combo more than once.
sudo dkms install -m 8812au -v 1.0
Module 8812au/1.0 already installed on kernel 4.4.0-38-generic/i686

τωρα δεν ξερω αν ειναι το error επειδη ξαναετρεξα τις ιδιες εντολες

Τον κώδικα τον βάζουμε μέσα σε [cοde]κώδικας[/cοde]. Επιλέγουμε το κείμενο και πατάμε το κουμπάκι Εικόνα.

Τελευταία επεξεργασία από fog και 27 Σεπ 2016, 11:24, έχει επεξεργασθεί 1 φορά/ες συνολικά
Αιτία: Προσθήκη κώδικα σε bbcode και alert
dentaltech_13
babeTUX
babeTUX
 
Δημοσιεύσεις: 5
Εγγραφή: 25 Σεπ 2016, 23:55
Εκτύπωση

Re: ΠΡΟΒΛΗΜΑ ΜΕ TP LINK TL-WN822N

Δημοσίευσηαπό dentaltech_13 » 27 Σεπ 2016, 00:34

ετρεξα τωρα την εντολη dmesg και πηρα αυτα τα αποτελεσματα

Κώδικας: Επιλογή όλων
ith 58:98:35:8c:54:c5
[  666.324361] wlan0: send auth to 58:98:35:8c:54:c5 (try 1/3)
[  666.328425] wlan0: authenticated
[  666.332318] wlan0: associate with 58:98:35:8c:54:c5 (try 1/3)
[  666.337312] wlan0: RX AssocResp from 58:98:35:8c:54:c5 (capab=0x411 status=0 aid=4)
[  666.337430] wlan0: associated
[  717.440168] ieee80211 phy0: rt2x00queue_flush_queue: Warning - Queue 2 failed to flush
[  717.940152] ieee80211 phy0: rt2x00queue_flush_queue: Warning - Queue 2 failed to flush
[  804.566486] usb 1-2: USB disconnect, device number 3
[  817.880210] usb 1-3: new high-speed USB device number 4 using ehci-pci
[  818.013446] usb 1-3: New USB device found, idVendor=2357, idProduct=0108
[  818.013465] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  818.013479] usb 1-3: Product: 802.11n NIC
[  818.013490] usb 1-3: Manufacturer: Realtek
[  818.013502] usb 1-3: SerialNumber: 00e04c000001


Τον κώδικα τον βάζουμε μέσα σε [cοde]κώδικας[/cοde]. Επιλέγουμε το κείμενο και πατάμε το κουμπάκι Εικόνα.

Τελευταία επεξεργασία από fog και 27 Σεπ 2016, 11:25, έχει επεξεργασθεί 1 φορά/ες συνολικά
Αιτία: Προσθήκη κώδικα σε bbcode και alert
dentaltech_13
babeTUX
babeTUX
 
Δημοσιεύσεις: 5
Εγγραφή: 25 Σεπ 2016, 23:55
Εκτύπωση

Re: ΠΡΟΒΛΗΜΑ ΜΕ TP LINK TL-WN822N

Δημοσίευσηαπό Learner » 27 Σεπ 2016, 20:59

dentaltech_13 έγραψε:μετα εκανα παλι την ιδια διαδικασια γιατι δεν ειχα κανει copy την πρωτη φορα και μου εμφανιζει ενα error
dentaltech_13 έγραψε:τωρα δεν ξερω αν ειναι το error επειδη ξαναετρεξα τις ιδιες εντολες

Ακριβώς αυτό.

dentaltech_13 έγραψε:ετρεξα τωρα την εντολη dmesg και πηρα αυτα τα αποτελεσματα

Στο νέο dmesg δε φαίνεται κάποιο error, σε σχέση με το παλιό
Κώδικας: Επιλογή όλων
eee80211 phy0: rt2x00queue_flush_queue: Warning - Queue 2 failed to flush


Αφού συνδέσεις το USB, κλείσε το WiFi (πρέπει να έχει κάποιο κουμπί λογικά ή συνδυασμό πλήκτρων).

Και μετά ας δούμε τι λέει ο NetworkManager.
Κώδικας: Επιλογή όλων
systemctl status NetworkManager

About Me
Xenial Xerus MuQSS Linux kernel
NickT@Ubuntu

Spoiler: show
1. Ubuntu Xenial (MATE), Arch Linux (GNOME)
2. Intel Core i3 CPU M 380 2.53GHz ‖ RAM 6GB ‖ Acer Aspire 5733
3. Intel Integrated Graphics [8086:0046] {i915}
4. wlan0: Atheros Inc. AR9485 Wireless Network Adapter [168c:0032] (rev 01)
Άβαταρ μέλους
Learner
Συντονιστής
Συντονιστής
 
Δημοσιεύσεις: 9711
Εγγραφή: 08 Νοέμ 2010, 21:24
Τοποθεσία: Αθήνα
Launchpad: NickThom
IRC: NikTh
Εκτύπωση

Re: ΠΡΟΒΛΗΜΑ ΜΕ TP LINK TL-WN822N

Δημοσίευσηαπό dentaltech_13 » 28 Σεπ 2016, 22:29

Κώδικας: Επιλογή όλων
NetworkManager.service - Network Manager
   Loaded: loaded (/lib/systemd/system/NetworkManager.service; enabled; vendor p
   Active: active (running) since Τετ 2016-09-28 12:48:29 EEST; 3min 10s ago
Main PID: 763 (NetworkManager)
   CGroup: /system.slice/NetworkManager.service
           └─763 /usr/sbin/NetworkManager --no-daemon

XPRESS-BOOK NetworkManager[763]: <info>  [1475056114.76
XPRESS-BOOK NetworkManager[763]: <info>  [1475056114.76
XPRESS-BOOK NetworkManager[763]: <info>  [1475056114.86
XPRESS-BOOK NetworkManager[763]: <info>  [1475056114.86
XPRESS-BOOK NetworkManager[763]: <info>  [1475056115.97
XPRESS-BOOK NetworkManager[763]: <info>  [1475056119.24
XPRESS-BOOK NetworkManager[763]: <info>  [1475056120.19
XPRESS-BOOK NetworkManager[763]: <info>  [1475056120.19
XPRESS-BOOK NetworkManager[763]: <info>  [1475056160.02
XPRESS-BOOK NetworkManager[763]: <info>  [1475056160.02
lines 1-17/17 (END)


dmesg
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000003f5b1fff]
[    0.000000] On node 0 totalpages: 259407
[    0.000000]   DMA zone: 40 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3997 pages, LIFO batch:0
[    0.000000]   Normal zone: 2190 pages used for memmap
[    0.000000]   Normal zone: 224254 pages, LIFO batch:31
[    0.000000]   HighMem zone: 31156 pages, LIFO batch:7
[    0.000000] Using APIC driver default
[    0.000000] Reserving Intel graphics stolen memory at 0x3f800000-0x3fffffff
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009efff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[    0.000000] e820: [mem 0x40000000-0xffafffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
[    0.000000] PERCPU: Embedded 19 pages/cpu @f71b1000 s47436 r0 d30388 u77824
[    0.000000] pcpu-alloc: s47436 r0 d30388 u77824 alloc=19*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 257177
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.4.0-38-generic root=UUID=4cb5f5e5-b1a7-48e9-9cb3-823457706c36 ro quiet splash zswap.enabled=1 vt.handoff=7
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] Initializing HighMem for node 0 (00037bfe:0003f5b2)
[    0.000000] Initializing Movable for node 0 (00000000:00000000)
[    0.000000] Memory: 977992K/1037628K available (7890K kernel code, 767K rwdata, 3136K rodata, 940K init, 800K bss, 59636K reserved, 0K cma-reserved, 124624K highmem)
[    0.000000] virtual kernel memory layout:
                   fixmap  : 0xfff15000 - 0xfffff000   ( 936 kB)
                   pkmap   : 0xffc00000 - 0xffe00000   (2048 kB)
                   vmalloc : 0xf83fe000 - 0xffbfe000   ( 120 MB)
                   lowmem  : 0xc0000000 - 0xf7bfe000   ( 891 MB)
                     .init : 0xc1b88000 - 0xc1c73000   ( 940 kB)
                     .data : 0xc17b4d93 - 0xc1b86fc0   (3912 kB)
                     .text : 0xc1000000 - 0xc17b4d93   (7891 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]    Build-time adjustment of leaf fanout to 32.
[    0.000000]    RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
[    0.000000] NR_IRQS:2304 nr_irqs:440 16
[    0.000000] CPU 0 irqstacks, hard=f6c38000 soft=f6c3a000
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] vt handoff: transparent VT on vt#7
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 1048576 bytes of page_ext
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 1600.083 MHz processor
[    0.008025] Calibrating delay loop (skipped), value calculated using timer frequency.. 3200.16 BogoMIPS (lpj=6400332)
[    0.008034] pid_max: default: 32768 minimum: 301
[    0.008061] ACPI: Core revision 20150930
[    0.026429] ACPI: 4 ACPI AML tables successfully acquired and loaded
[    0.026486] Security Framework initialized
[    0.026492] Yama: becoming mindful.
[    0.026538] AppArmor: AppArmor initialized
[    0.026642] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.026649] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.027175] Initializing cgroup subsys io
[    0.027189] Initializing cgroup subsys memory
[    0.027210] Initializing cgroup subsys devices
[    0.027219] Initializing cgroup subsys freezer
[    0.027228] Initializing cgroup subsys net_cls
[    0.027237] Initializing cgroup subsys perf_event
[    0.027246] Initializing cgroup subsys net_prio
[    0.027258] Initializing cgroup subsys hugetlb
[    0.027266] Initializing cgroup subsys pids
[    0.027311] Disabled fast string operations
[    0.027318] CPU: Physical Processor ID: 0
[    0.027322] CPU: Processor Core ID: 0
[    0.027331] mce: CPU supports 5 MCE banks
[    0.027346] CPU0: Thermal monitoring enabled (TM2)
[    0.027355] process: using mwait in idle threads
[    0.027371] Last level iTLB entries: 4KB 32, 2MB 0, 4MB 0
[    0.027376] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 8, 1GB 0
[    0.028223] Freeing SMP alternatives memory: 28K (c1c73000 - c1c7a000)
[    0.032032] ftrace: allocating 31293 entries in 62 pages
[    0.052207] smpboot: Max logical packages: 2
[    0.052215] smpboot: APIC(0) Converting physical 0 to logical package 0
[    0.052224] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.052605] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
[    0.096000] smpboot: CPU0: Intel(R) Atom(TM) CPU N270   @ 1.60GHz (family: 0x6, model: 0x1c, stepping: 0x2)
[    0.096000] Performance Events: PEBS fmt0+, LBR disabled due to erratumAtom events, Intel PMU driver.
[    0.096000] ... version:                3
[    0.096000] ... bit width:              40
[    0.096000] ... generic registers:      2
[    0.096000] ... value mask:             000000ffffffffff
[    0.096000] ... max period:             000000007fffffff
[    0.096000] ... fixed-purpose events:   3
[    0.096000] ... event mask:             0000000700000003
[    0.096000] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.096000] CPU 1 irqstacks, hard=f6e96000 soft=f6e98000
[    0.096000] x86: Booting SMP configuration:
[    0.096000] .... node  #0, CPUs:      #1
[    0.012000] Initializing CPU#1
[    0.012000] Disabled fast string operations
[    0.096080] x86: Booted up 1 node, 2 CPUs
[    0.096095] smpboot: Total of 2 processors activated (6400.33 BogoMIPS)
[    0.096700] devtmpfs: initialized
[    0.096893] evm: security.selinux
[    0.096898] evm: security.SMACK64
[    0.096902] evm: security.SMACK64EXEC
[    0.096905] evm: security.SMACK64TRANSMUTE
[    0.096909] evm: security.SMACK64MMAP
[    0.096912] evm: security.ima
[    0.096916] evm: security.capability
[    0.097160] PM: Registering ACPI NVS region [mem 0x3f5b2000-0x3f5d4fff] (143360 bytes)
[    0.097170] PM: Registering ACPI NVS region [mem 0x3f5e6000-0x3f5e8fff] (12288 bytes)
[    0.097176] PM: Registering ACPI NVS region [mem 0x3f605000-0x3f605fff] (4096 bytes)
[    0.097181] PM: Registering ACPI NVS region [mem 0x3f611000-0x3f616fff] (24576 bytes)
[    0.097455] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.097673] pinctrl core: initialized pinctrl subsystem
[    0.098052] RTC time:  9:47:55, date: 09/28/16
[    0.098432] NET: Registered protocol family 16
[    0.099122] EISA bus registered
[    0.108017] cpuidle: using governor ladder
[    0.116016] cpuidle: using governor menu
[    0.116028] PCCT header not found.
[    0.116261] ACPI: bus type PCI registered
[    0.116270] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.116502] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.116510] PCI: not using MMCONFIG
[    0.201387] PCI: Using configuration type 1 for base access
[    0.216393] ACPI: Added _OSI(Module Device)
[    0.216400] ACPI: Added _OSI(Processor Device)
[    0.216406] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.216410] ACPI: Added _OSI(Processor Aggregator Device)
[    0.222796] ACPI: Executed 1 blocks of module-level executable AML code
[    0.226894] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.227688] ACPI: Dynamic OEM Table Load:
[    0.227705] ACPI: SSDT 0x00000000F6E26400 000253 (v02 PmRef  Cpu0Ist  00003000 INTL 20051117)
[    0.228726] ACPI: Dynamic OEM Table Load:
[    0.228746] ACPI: SSDT 0x00000000F6C11800 000653 (v02 PmRef  Cpu0Cst  00003001 INTL 20051117)
[    0.230321] ACPI: Dynamic OEM Table Load:
[    0.230335] ACPI: SSDT 0x00000000F6E7E500 0000D0 (v02 PmRef  Cpu1Ist  00003000 INTL 20051117)
[    0.231108] ACPI: Dynamic OEM Table Load:
[    0.231121] ACPI: SSDT 0x00000000F6CA4A80 000083 (v02 PmRef  Cpu1Cst  00003000 INTL 20051117)
[    0.232114] ACPI : EC: EC started
[    0.232522] ACPI: Interpreter enabled
[    0.232557] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150930/hwxface-580)
[    0.232595] ACPI: (supports S0 S1 S3 S4 S5)
[    0.232600] ACPI: Using IOAPIC for interrupt routing
[    0.232705] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.232967] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[    0.232972] PCI: Using MMCONFIG for extended config space
[    0.232985] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.255571] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.255589] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.256324] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[    0.256980] PCI host bridge to bus 0000:00
[    0.256991] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.256999] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.257006] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.257012] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000fffff window]
[    0.257019] pci_bus 0000:00: root bus resource [mem 0x40000000-0xffefffff window]
[    0.257027] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.257049] pci 0000:00:00.0: [8086:27ac] type 00 class 0x060000
[    0.257354] pci 0000:00:02.0: [8086:27ae] type 00 class 0x030000
[    0.257381] pci 0000:00:02.0: reg 0x10: [mem 0xdfe80000-0xdfefffff]
[    0.257393] pci 0000:00:02.0: reg 0x14: [io  0xe0f0-0xe0f7]
[    0.257405] pci 0000:00:02.0: reg 0x18: [mem 0xc0000000-0xcfffffff pref]
[    0.257417] pci 0000:00:02.0: reg 0x1c: [mem 0xdff00000-0xdff3ffff]
[    0.257702] pci 0000:00:02.1: [8086:27a6] type 00 class 0x038000
[    0.257725] pci 0000:00:02.1: reg 0x10: [mem 0xdfe00000-0xdfe7ffff]
[    0.258042] pci 0000:00:1b.0: [8086:27d8] type 00 class 0x040300
[    0.258084] pci 0000:00:1b.0: reg 0x10: [mem 0xffe00000-0xffe03fff 64bit]
[    0.258176] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.258446] pci 0000:00:1c.0: [8086:27d0] type 01 class 0x060400
[    0.258553] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.258690] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.258859] pci 0000:00:1c.1: [8086:27d2] type 01 class 0x060400
[    0.258965] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.259103] pci 0000:00:1c.1: System wakeup disabled by ACPI
[    0.259271] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
[    0.259329] pci 0000:00:1d.0: reg 0x20: [io  0xe080-0xe09f]
[    0.259531] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.259698] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
[    0.259757] pci 0000:00:1d.1: reg 0x20: [io  0xe060-0xe07f]
[    0.259954] pci 0000:00:1d.1: System wakeup disabled by ACPI
[    0.260142] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
[    0.260200] pci 0000:00:1d.2: reg 0x20: [io  0xe040-0xe05f]
[    0.260400] pci 0000:00:1d.2: System wakeup disabled by ACPI
[    0.260568] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300
[    0.260627] pci 0000:00:1d.3: reg 0x20: [io  0xe020-0xe03f]
[    0.260828] pci 0000:00:1d.3: System wakeup disabled by ACPI
[    0.261015] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
[    0.261054] pci 0000:00:1d.7: reg 0x10: [mem 0xdff40000-0xdff403ff]
[    0.261153] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.261283] pci 0000:00:1d.7: System wakeup disabled by ACPI
[    0.261447] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401
[    0.261637] pci 0000:00:1e.0: System wakeup disabled by ACPI
[    0.261812] pci 0000:00:1f.0: [8086:27b9] type 00 class 0x060100
[    0.261939] pci 0000:00:1f.0: Force enabled HPET at 0xfed03000
[    0.261962] pci 0000:00:1f.0: can't claim BAR 13 [io  0x0400-0x047f]: address conflict with ACPI CPU throttle [io  0x0410-0x0415]
[    0.261973] pci 0000:00:1f.0: quirk: [io  0x0500-0x053f] claimed by ICH6 GPIO
[    0.261981] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 004c (mask 0007)
[    0.262261] pci 0000:00:1f.2: [8086:27c4] type 00 class 0x010180
[    0.262291] pci 0000:00:1f.2: reg 0x10: [io  0xe0e0-0xe0e7]
[    0.262306] pci 0000:00:1f.2: reg 0x14: [io  0xe0d0-0xe0d3]
[    0.262320] pci 0000:00:1f.2: reg 0x18: [io  0xe0c0-0xe0c7]
[    0.262334] pci 0000:00:1f.2: reg 0x1c: [io  0xe0b0-0xe0b3]
[    0.262348] pci 0000:00:1f.2: reg 0x20: [io  0xe0a0-0xe0af]
[    0.262374] pci 0000:00:1f.2: legacy IDE quirk: reg 0x10: [io  0x01f0-0x01f7]
[    0.262380] pci 0000:00:1f.2: legacy IDE quirk: reg 0x14: [io  0x03f6]
[    0.262386] pci 0000:00:1f.2: legacy IDE quirk: reg 0x18: [io  0x0170-0x0177]
[    0.262392] pci 0000:00:1f.2: legacy IDE quirk: reg 0x1c: [io  0x0376]
[    0.262425] pci 0000:00:1f.2: PME# supported from D3hot
[    0.262683] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
[    0.262753] pci 0000:00:1f.3: reg 0x20: [io  0xe000-0xe01f]
[    0.263184] pci 0000:01:00.0: [10ec:8136] type 00 class 0x020000
[    0.263240] pci 0000:01:00.0: reg 0x10: [io  0xd000-0xd0ff]
[    0.263278] pci 0000:01:00.0: reg 0x18: [mem 0xffd10000-0xffd10fff 64bit pref]
[    0.263304] pci 0000:01:00.0: reg 0x20: [mem 0xffd00000-0xffd0ffff 64bit pref]
[    0.263322] pci 0000:01:00.0: reg 0x30: [mem 0xdfd00000-0xdfd1ffff pref]
[    0.263408] pci 0000:01:00.0: supports D1 D2
[    0.263415] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.268043] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.268054] pci 0000:00:1c.0:   bridge window [io  0xd000-0xdfff]
[    0.268063] pci 0000:00:1c.0:   bridge window [mem 0xdfd00000-0xdfdfffff]
[    0.268074] pci 0000:00:1c.0:   bridge window [mem 0xffd00000-0xffdfffff 64bit pref]
[    0.268257] pci 0000:02:00.0: [1814:0781] type 00 class 0x028000
[    0.268306] pci 0000:02:00.0: reg 0x10: [mem 0xdfc00000-0xdfc0ffff]
[    0.268440] pci 0000:02:00.0: PME# supported from D0 D3hot
[    0.276034] pci 0000:00:1c.1: PCI bridge to [bus 02]
[    0.276047] pci 0000:00:1c.1:   bridge window [mem 0xdfc00000-0xdfcfffff]
[    0.276212] pci 0000:00:1e.0: PCI bridge to [bus 03] (subtractive decode)
[    0.276230] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7 window] (subtractive decode)
[    0.276237] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff window] (subtractive decode)
[    0.276244] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[    0.276250] pci 0000:00:1e.0:   bridge window [mem 0x000c0000-0x000fffff window] (subtractive decode)
[    0.276257] pci 0000:00:1e.0:   bridge window [mem 0x40000000-0xffefffff window] (subtractive decode)
[    0.276283] pci_bus 0000:00: on NUMA node 0
[    0.281162] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.281344] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.281522] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[    0.281700] ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
[    0.281876] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.282054] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.282233] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.282413] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.282788] ACPI : EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[    0.283134] vgaarb: setting as boot device: PCI:0000:00:02.0
[    0.283134] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.283134] vgaarb: loaded
[    0.283134] vgaarb: bridge control possible 0000:00:02.0
[    0.284392] SCSI subsystem initialized
[    0.284553] libata version 3.00 loaded.
[    0.284661] ACPI: bus type USB registered
[    0.284744] usbcore: registered new interface driver usbfs
[    0.284788] usbcore: registered new interface driver hub
[    0.284847] usbcore: registered new device driver usb
[    0.285050] PCI: Using ACPI for IRQ routing
[    0.291947] PCI: pci_cache_line_size set to 64 bytes
[    0.292034] e820: reserve RAM buffer [mem 0x0009ec00-0x0009ffff]
[    0.292041] e820: reserve RAM buffer [mem 0x3f5b2000-0x3fffffff]
[    0.292504] NetLabel: Initializing
[    0.292509] NetLabel:  domain hash size = 128
[    0.292513] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.292545] NetLabel:  unlabeled traffic allowed by default
[    0.292643] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[    0.292643] hpet clockevent registered
[    0.292643] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.292643] hpet0: at MMIO 0xfed03000, IRQs 2, 8, 0
[    0.292643] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.296038] amd_nb: Cannot enumerate AMD northbridges
[    0.296064] clocksource: Switched to clocksource hpet
[    0.318265] AppArmor: AppArmor Filesystem Enabled
[    0.318503] pnp: PnP ACPI init
[    0.319003] system 00:00: [mem 0xfed14000-0xfed17fff] has been reserved
[    0.319013] system 00:00: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.319021] system 00:00: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.319028] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[    0.319041] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.319241] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.319442] system 00:02: [io  0x04d0-0x04d1] has been reserved
[    0.319454] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.319600] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    0.319738] pnp 00:04: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active)
[    0.324586] system 00:05: [io  0x0400-0x047f] could not be reserved
[    0.324596] system 00:05: [io  0x1180-0x119f] has been reserved
[    0.324604] system 00:05: [io  0x0500-0x053f] has been reserved
[    0.324613] system 00:05: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.324621] system 00:05: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.324629] system 00:05: [mem 0xfed20000-0xfed23fff] has been reserved
[    0.324636] system 00:05: [mem 0xffb00000-0xffbfffff] has been reserved
[    0.324644] system 00:05: [mem 0xfc800400-0xfc800fff] has been reserved
[    0.324656] system 00:05: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.325194] pnp: PnP ACPI: found 6 devices
[    0.325211] PnPBIOS: Disabled by ACPI PNP
[    0.368697] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.368756] pci 0000:00:1c.1: bridge window [io  0x1000-0x0fff] to [bus 02] add_size 1000
[    0.368768] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000 add_align 100000
[    0.368793] pci 0000:00:1f.0: BAR 13: [io  size 0x0080] has bogus alignment
[    0.368808] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x000fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.368817] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x002fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.368824] pci 0000:00:1c.1: res[13]=[io  0x1000-0x0fff] res_to_dev_res add_size 1000 min_align 1000
[    0.368832] pci 0000:00:1c.1: res[13]=[io  0x1000-0x1fff] res_to_dev_res add_size 1000 min_align 1000
[    0.368858] pci 0000:00:1c.1: BAR 15: assigned [mem 0x40000000-0x401fffff 64bit pref]
[    0.368869] pci 0000:00:1c.1: BAR 13: assigned [io  0x2000-0x2fff]
[    0.368881] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.368889] pci 0000:00:1c.0:   bridge window [io  0xd000-0xdfff]
[    0.368900] pci 0000:00:1c.0:   bridge window [mem 0xdfd00000-0xdfdfffff]
[    0.368909] pci 0000:00:1c.0:   bridge window [mem 0xffd00000-0xffdfffff 64bit pref]
[    0.368920] pci 0000:00:1c.1: PCI bridge to [bus 02]
[    0.368928] pci 0000:00:1c.1:   bridge window [io  0x2000-0x2fff]
[    0.368938] pci 0000:00:1c.1:   bridge window [mem 0xdfc00000-0xdfcfffff]
[    0.368947] pci 0000:00:1c.1:   bridge window [mem 0x40000000-0x401fffff 64bit pref]
[    0.368959] pci 0000:00:1e.0: PCI bridge to [bus 03]
[    0.368978] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.368985] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.368992] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.368998] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000fffff window]
[    0.369005] pci_bus 0000:00: resource 8 [mem 0x40000000-0xffefffff window]
[    0.369012] pci_bus 0000:01: resource 0 [io  0xd000-0xdfff]
[    0.369018] pci_bus 0000:01: resource 1 [mem 0xdfd00000-0xdfdfffff]
[    0.369025] pci_bus 0000:01: resource 2 [mem 0xffd00000-0xffdfffff 64bit pref]
[    0.369032] pci_bus 0000:02: resource 0 [io  0x2000-0x2fff]
[    0.369038] pci_bus 0000:02: resource 1 [mem 0xdfc00000-0xdfcfffff]
[    0.369045] pci_bus 0000:02: resource 2 [mem 0x40000000-0x401fffff 64bit pref]
[    0.369052] pci_bus 0000:03: resource 4 [io  0x0000-0x0cf7 window]
[    0.369059] pci_bus 0000:03: resource 5 [io  0x0d00-0xffff window]
[    0.369065] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.369072] pci_bus 0000:03: resource 7 [mem 0x000c0000-0x000fffff window]
[    0.369079] pci_bus 0000:03: resource 8 [mem 0x40000000-0xffefffff window]
[    0.369154] NET: Registered protocol family 2
[    0.369644] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.369692] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.369751] TCP: Hash tables configured (established 8192 bind 8192)
[    0.369809] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.369828] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.369960] NET: Registered protocol family 1
[    0.370008] pci 0000:00:02.0: Video device with shadowed ROM
[    0.371506] PCI: CLS 64 bytes, default 64
[    0.371682] Trying to unpack rootfs image as initramfs...
[    1.960880] Freeing initrd memory: 34560K (f3c70000 - f5e30000)
[    1.961434] Scanning for low memory corruption every 60 seconds
[    1.962565] futex hash table entries: 512 (order: 3, 32768 bytes)
[    1.962632] audit: initializing netlink subsys (disabled)
[    1.962677] audit: type=2000 audit(1475056076.960:1): initialized
[    1.963661] Initialise system trusted keyring
[    1.963997] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.971331] zbud: loaded
[    1.971700] VFS: Disk quotas dquot_6.6.0
[    1.971856] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.973002] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.974042] fuse init (API version 7.23)
[    1.974630] Key type big_key registered
[    1.974690] Allocating IMA MOK and blacklist keyrings.
[    1.975806] Key type asymmetric registered
[    1.975817] Asymmetric key parser 'x509' registered
[    1.975869] bounce: pool size: 64 pages
[    1.976081] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    1.976187] io scheduler noop registered
[    1.976196] io scheduler deadline registered (default)
[    1.976339] io scheduler cfq registered
[    1.977790] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
[    1.977800] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[    1.977809] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
[    1.977871] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt
[    1.977878] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[    1.977887] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded
[    1.977918] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.977953] pciehp 0000:00:1c.0:pcie04: Slot #0 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl- LLActRep+
[    1.978060] pciehp 0000:00:1c.0:pcie04: service driver pciehp loaded
[    1.978088] pciehp 0000:00:1c.1:pcie04: Slot #0 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl- LLActRep+
[    1.978167] pciehp 0000:00:1c.1:pcie04: service driver pciehp loaded
[    1.978192] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.978320] vesafb: mode is 800x600x32, linelength=3200, pages=0
[    1.978325] vesafb: scrolling: redraw
[    1.978331] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    1.978376] vesafb: framebuffer at 0xc0000000, mapped to 0xf8600000, using 1920k, total 1920k
[    1.978734] Console: switching to colour frame buffer device 100x37
[    1.978770] fb0: VESA VGA frame buffer device
[    1.978842] intel_idle: MWAIT substates: 0x20220
[    1.978860] intel_idle: v0.4.1 model 0x1C
[    1.978865] intel_idle: lapic_timer_reliable_states 0x2
[    1.978880] tsc: Marking TSC unstable due to TSC halts in idle states deeper than C2
[    1.984212] ACPI: AC Adapter [ADP1] (off-line)
[    1.984470] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:10/PNP0C09:00/PNP0C0D:00/input/input0
[    1.988094] ACPI: Lid Switch [LID0]
[    1.988282] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[    1.988292] ACPI: Power Button [PWRB]
[    1.988462] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[    1.988470] ACPI: Sleep Button [SLPB]
[    1.988648] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    1.988656] ACPI: Power Button [PWRF]
[    2.009535] thermal LNXTHERM:00: registered as thermal_zone0
[    2.009543] ACPI: Thermal Zone [THRM] (56 C)
[    2.009686] GHES: HEST is not enabled!
[    2.009925] isapnp: Scanning for PnP cards...
[    2.010344] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    2.019633] Linux agpgart interface v0.103
[    2.019888] agpgart-intel 0000:00:00.0: Intel 945GME Chipset
[    2.019936] agpgart-intel 0000:00:00.0: detected gtt size: 262144K total, 262144K mappable
[    2.020072] agpgart-intel 0000:00:00.0: detected 8192K stolen memory
[    2.020384] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
[    2.049486] brd: module loaded
[    2.057026] loop: module loaded
[    2.057881] ata_piix 0000:00:1f.2: version 2.13
[    2.058131] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[    2.184100] ACPI: Battery Slot [BAT1] (battery present)
[    2.213775] scsi host0: ata_piix
[    2.214221] scsi host1: ata_piix
[    2.214484] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xe0a0 irq 14
[    2.214493] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xe0a8 irq 15
[    2.214978] libphy: Fixed MDIO Bus: probed
[    2.214989] tun: Universal TUN/TAP device driver, 1.6
[    2.214994] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    2.215354] PPP generic driver version 2.4.2
[    2.215670] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.215690] ehci-pci: EHCI PCI platform driver
[    2.216060] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    2.216087] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    2.216116] ehci-pci 0000:00:1d.7: debug port 1
[    2.220070] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
[    2.220273] ehci-pci 0000:00:1d.7: irq 23, io mem 0xdff40000
[    2.232051] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    2.232252] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.232261] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.232269] usb usb1: Product: EHCI Host Controller
[    2.232277] usb usb1: Manufacturer: Linux 4.4.0-38-generic ehci_hcd
[    2.232284] usb usb1: SerialNumber: 0000:00:1d.7
[    2.232889] hub 1-0:1.0: USB hub found
[    2.232921] hub 1-0:1.0: 8 ports detected
[    2.233962] ehci-platform: EHCI generic platform driver
[    2.234035] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.234054] ohci-pci: OHCI PCI platform driver
[    2.234121] ohci-platform: OHCI generic platform driver
[    2.234173] uhci_hcd: USB Universal Host Controller Interface driver
[    2.234446] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    2.234470] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    2.234488] uhci_hcd 0000:00:1d.0: detected 2 ports
[    2.234527] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e080
[    2.234746] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.234755] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.234763] usb usb2: Product: UHCI Host Controller
[    2.234771] usb usb2: Manufacturer: Linux 4.4.0-38-generic uhci_hcd
[    2.234778] usb usb2: SerialNumber: 0000:00:1d.0
[    2.235369] hub 2-0:1.0: USB hub found
[    2.235399] hub 2-0:1.0: 2 ports detected
[    2.236167] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    2.236192] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    2.236210] uhci_hcd 0000:00:1d.1: detected 2 ports
[    2.236279] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e060
[    2.236492] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    2.236501] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.236509] usb usb3: Product: UHCI Host Controller
[    2.236517] usb usb3: Manufacturer: Linux 4.4.0-38-generic uhci_hcd
[    2.236524] usb usb3: SerialNumber: 0000:00:1d.1
[    2.237128] hub 3-0:1.0: USB hub found
[    2.237159] hub 3-0:1.0: 2 ports detected
[    2.237879] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    2.237903] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    2.237921] uhci_hcd 0000:00:1d.2: detected 2 ports
[    2.237985] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e040
[    2.238201] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    2.238211] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.238219] usb usb4: Product: UHCI Host Controller
[    2.238226] usb usb4: Manufacturer: Linux 4.4.0-38-generic uhci_hcd
[    2.238234] usb usb4: SerialNumber: 0000:00:1d.2
[    2.238818] hub 4-0:1.0: USB hub found
[    2.238847] hub 4-0:1.0: 2 ports detected
[    2.239521] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    2.239545] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    2.239563] uhci_hcd 0000:00:1d.3: detected 2 ports
[    2.239628] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e020
[    2.239843] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    2.239853] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.239861] usb usb5: Product: UHCI Host Controller
[    2.239868] usb usb5: Manufacturer: Linux 4.4.0-38-generic uhci_hcd
[    2.239876] usb usb5: SerialNumber: 0000:00:1d.3
[    2.240513] hub 5-0:1.0: USB hub found
[    2.240544] hub 5-0:1.0: 2 ports detected
[    2.241324] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    2.259593] serio: i8042 KBD port at 0x60,0x64 irq 1
[    2.259614] serio: i8042 AUX port at 0x60,0x64 irq 12
[    2.260404] mousedev: PS/2 mouse device common for all mice
[    2.261321] rtc_cmos 00:01: RTC can wake from S4
[    2.261670] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[    2.261720] rtc_cmos 00:01: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[    2.261766] i2c /dev entries driver
[    2.262074] device-mapper: uevent: version 1.0.3
[    2.262445] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[    2.262584] platform eisa.0: Probing EISA bus 0
[    2.262596] platform eisa.0: EISA: Cannot allocate resource for mainboard
[    2.262606] platform eisa.0: Cannot allocate resource for EISA slot 1
[    2.262616] platform eisa.0: Cannot allocate resource for EISA slot 2
[    2.262625] platform eisa.0: Cannot allocate resource for EISA slot 3
[    2.262635] platform eisa.0: Cannot allocate resource for EISA slot 4
[    2.262644] platform eisa.0: Cannot allocate resource for EISA slot 5
[    2.262654] platform eisa.0: Cannot allocate resource for EISA slot 6
[    2.262663] platform eisa.0: Cannot allocate resource for EISA slot 7
[    2.262673] platform eisa.0: Cannot allocate resource for EISA slot 8
[    2.262681] platform eisa.0: EISA: Detected 0 cards
[    2.262732] cpufreq-nforce2: No nForce2 chipset.
[    2.262759] ledtrig-cpu: registered to indicate activity on CPUs
[    2.264254] NET: Registered protocol family 10
[    2.265226] NET: Registered protocol family 17
[    2.265270] Key type dns_resolver registered
[    2.266225] microcode: CPU0 sig=0x106c2, pf=0x4, revision=0x212
[    2.266253] microcode: CPU1 sig=0x106c2, pf=0x4, revision=0x212
[    2.266430] microcode: Microcode Update Driver: v2.01 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    2.266464] Using IPI No-Shortcut mode
[    2.267191] registered taskstats version 1
[    2.267237] Loading compiled-in X.509 certificates
[    2.279148] Loaded X.509 cert 'Build time autogenerated kernel key: d4f6fa2e18e18df694cd7c2d31721a88bb16e626'
[    2.279230] zswap: loaded using pool lzo/zbud
[    2.288966] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[    2.289982] Key type trusted registered
[    2.310848] Key type encrypted registered
[    2.310875] AppArmor: AppArmor sha1 policy hashing enabled
[    2.310886] ima: No TPM chip found, activating TPM-bypass!
[    2.310962] evm: HMAC attrs: 0x1
[    2.311746]   Magic number: 0:313:779
[    2.311929] rtc_cmos 00:01: setting system clock to 2016-09-28 09:47:58 UTC (1475056078)
[    2.313456] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    2.313463] EDD information not available.
[    2.313831] PM: Hibernation image not present or could not be loaded.
[    2.320526] isapnp: No Plug & Play device found
[    2.423800] ata1.00: ATA-8: ST9250315AS, 0001SDM1, max UDMA/133
[    2.423818] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    2.452817] ata1.00: configured for UDMA/133
[    2.453332] scsi 0:0:0:0: Direct-Access     ATA      ST9250315AS      SDM1 PQ: 0 ANSI: 5
[    2.453995] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/233 GiB)
[    2.454192] sd 0:0:0:0: [sda] Write Protect is off
[    2.454205] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.454215] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.454295] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.505584]  sda: sda1 sda2 sda3 < sda5 sda6 >
[    2.507192] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.508143] Freeing unused kernel memory: 940K (c1b88000 - c1c73000)
[    2.508361] Write protecting the kernel text: 7892k
[    2.508452] Write protecting the kernel read-only data: 3144k
[    2.508458] NX-protecting the kernel data: 6444k
[    2.546617] random: systemd-udevd: uninitialized urandom read (16 bytes read, 19 bits of entropy available)
[    2.547054] random: systemd-udevd: uninitialized urandom read (16 bytes read, 19 bits of entropy available)
[    2.547198] random: systemd-udevd: uninitialized urandom read (16 bytes read, 19 bits of entropy available)
[    2.548723] random: udevadm: uninitialized urandom read (16 bytes read, 19 bits of entropy available)
[    2.548986] random: udevadm: uninitialized urandom read (16 bytes read, 19 bits of entropy available)
[    2.549986] random: udevadm: uninitialized urandom read (16 bytes read, 19 bits of entropy available)
[    2.550458] random: udevadm: uninitialized urandom read (16 bytes read, 19 bits of entropy available)
[    2.550515] usb 1-2: new high-speed USB device number 2 using ehci-pci
[    2.550868] random: udevadm: uninitialized urandom read (16 bytes read, 19 bits of entropy available)
[    2.551156] random: udevadm: uninitialized urandom read (16 bytes read, 19 bits of entropy available)
[    2.551417] random: udevadm: uninitialized urandom read (16 bytes read, 19 bits of entropy available)
[    2.681221] usb 1-2: New USB device found, idVendor=2357, idProduct=0108
[    2.681234] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.681244] usb 1-2: Product: 802.11n NIC
[    2.681252] usb 1-2: Manufacturer: Realtek
[    2.681261] usb 1-2: SerialNumber: 00e04c000001
[    2.702871] ACPI: Video Device [IGD] (multi-head: yes  rom: no  post: no)
[    2.717029] atkbd serio0: Unknown key pressed (translated set 2, code 0xf8 on isa0060/serio0).
[    2.717042] atkbd serio0: Use 'setkeycodes e078 <keycode>' to make it known.
[    2.721106] atkbd serio0: Unknown key released (translated set 2, code 0xf8 on isa0060/serio0).
[    2.721119] atkbd serio0: Use 'setkeycodes e078 <keycode>' to make it known.
[    2.732105] FUJITSU Extended Socket Network Device Driver - version 1.0 - Copyright (c) 2015 FUJITSU LIMITED
[    2.733124] acpi device:1a: registered as cooling_device2
[    2.733450] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6
[    2.736602] atkbd serio0: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
[    2.736614] atkbd serio0: Use 'setkeycodes e077 <keycode>' to make it known.
[    2.740413] atkbd serio0: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0).
[    2.740426] atkbd serio0: Use 'setkeycodes e077 <keycode>' to make it known.
[    2.744096] wmi: Mapper loaded
[    2.808418] usb 1-6: new high-speed USB device number 3 using ehci-pci
[    2.832490] [drm] Initialized drm 1.1.0 20060810
[    2.932773] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    2.933912] r8169 0000:01:00.0 eth0: RTL8102e at 0xf8432000, 40:61:86:13:93:74, XID 14a00000 IRQ 26
[    2.960065] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x1710736b07c, max_idle_ns: 440795266809 ns
[    3.164863] usb 1-6: New USB device found, idVendor=0bda, idProduct=0158
[    3.164876] usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.164885] usb 1-6: Product: USB2.0-CRW
[    3.164893] usb 1-6: Manufacturer: Generic
[    3.164900] usb 1-6: SerialNumber: 20071114173400000
[    3.193299] [drm] Memory usable by graphics device = 256M
[    3.193314] checking generic (c0000000 1e0000) vs hw (c0000000 10000000)
[    3.193320] fb: switching to inteldrmfb from VESA VGA
[    3.193420] Console: switching to colour dummy device 80x25
[    3.193763] [drm] Replacing VGA console driver
[    3.193902] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    3.193909] [drm] Driver supports precise vblank timestamp query.
[    3.198039] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[    3.262169] usbcore: registered new interface driver usb-storage
[    3.275405] usbcore: registered new interface driver uas
[    3.292335] ums-realtek 1-6:1.0: USB Mass Storage device detected
[    3.306422] usb 1-6: USB disconnect, device number 3
[    3.310301] scsi host2: usb-storage 1-6:1.0
[    3.311156] usbcore: registered new interface driver ums-realtek
[    3.513416] [drm] initialized overlay support
[    3.513473] [drm] Initialized i915 1.6.0 20151010 for 0000:00:02.0 on minor 0
[    3.532444] ------------[ cut here ]------------
[    3.532602] WARNING: CPU: 1 PID: 6 at /build/linux-zfJcLg/linux-4.4.0/drivers/gpu/drm/i915/intel_fbdev.c:406 intel_fb_initial_config+0x2d4/0x5f0 [i915]()
[    3.532609] WARN_ON(!encoder->crtc)
[    3.532613] Modules linked in:
[    3.532619]  ums_realtek uas usb_storage i915 psmouse i2c_algo_bit drm_kms_helper r8169 syscopyarea sysfillrect pata_acpi sysimgblt fb_sys_fops drm mii wmi fjes video
[    3.532661] CPU: 1 PID: 6 Comm: kworker/u4:0 Not tainted 4.4.0-38-generic #57-Ubuntu
[    3.532668] Hardware name: MULTIRAMA_PC XPRESS BOOK/XPRESS BOOK, BIOS 4.6.3 06/17/2009
[    3.532681] Workqueue: events_unbound async_run_entry_fn
[    3.532689]  c1acf967 e4264d20 00000286 f6e29d04 c13a714f f6e29d44 f8a6d97c f6e29d34
[    3.532706]  c1070307 f8a7856e f6e29d64 00000006 f8a6d97c 00000196 f8a1d904 f8a1d904
[    3.532724]  00000000 00000001 00000001 f6e29d50 c107037e 00000009 f6e29d44 f8a7856e
[    3.532741] Call Trace:
[    3.532757]  [<c13a714f>] dump_stack+0x58/0x79
[    3.532770]  [<c1070307>] warn_slowpath_common+0x87/0xc0
[    3.532911]  [<f8a1d904>] ? intel_fb_initial_config+0x2d4/0x5f0 [i915]
[    3.533044]  [<f8a1d904>] ? intel_fb_initial_config+0x2d4/0x5f0 [i915]
[    3.533059]  [<c107037e>] warn_slowpath_fmt+0x3e/0x60
[    3.533188]  [<f8a1d904>] intel_fb_initial_config+0x2d4/0x5f0 [i915]
[    3.533325]  [<f8a1d630>] ? intel_crtc_fb_gamma_get+0x40/0x40 [i915]
[    3.533363]  [<f85d2ccf>] drm_setup_crtcs+0x21f/0xa90 [drm_kms_helper]
[    3.533378]  [<c10977a7>] ? ttwu_do_wakeup+0x17/0x110
[    3.533389]  [<c1098289>] ? try_to_wake_up+0x39/0x360
[    3.533399]  [<c10985c4>] ? wake_up_process+0x14/0x20
[    3.533434]  [<f85d37ec>] drm_fb_helper_initial_config+0xbc/0x400 [drm_kms_helper]
[    3.533448]  [<c10aa079>] ? pick_next_task_fair+0x459/0x520
[    3.533582]  [<f8a1e7f9>] intel_fbdev_initial_config+0x19/0x20 [i915]
[    3.533596]  [<c108f57e>] async_run_entry_fn+0x4e/0x170
[    3.533605]  [<c1087751>] process_one_work+0x121/0x3f0
[    3.533613]  [<c1087a57>] worker_thread+0x37/0x490
[    3.533620]  [<c1087a20>] ? process_one_work+0x3f0/0x3f0
[    3.533626]  [<c108cf06>] kthread+0xa6/0xc0
[    3.533635]  [<c17b2b09>] ret_from_kernel_thread+0x21/0x38
[    3.533641]  [<c108ce60>] ? kthread_create_on_node+0x170/0x170
[    3.533648] ---[ end trace ba29167eae6f935d ]---
[    3.537099] fbcon: inteldrmfb (fb0) is primary device
[    3.537422] Console: switching to colour frame buffer device 128x37
[    3.537501] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[    3.859992] psmouse serio1: synaptics: Touchpad model: 1, fw: 6.5, id: 0x1c0b1, caps: 0xa04711/0xa00000/0x0/0x0, board id: 0, fw id: 430020
[    3.923457] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
[    4.466730] ext4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[    4.756316] random: nonblocking pool is initialized
[    5.937637] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[    5.938080] systemd[1]: Detected architecture x86.
[    5.944443] systemd[1]: Set hostname to <christos-XPRESS-BOOK>.
[    8.001634] systemd[1]: Listening on Syslog Socket.
[    8.001974] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[    8.002168] systemd[1]: Listening on Journal Socket.
[    8.002309] systemd[1]: Listening on udev Kernel Socket.
[    8.002422] systemd[1]: Listening on fsck to fsckd communication Socket.
[    8.002594] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    8.002727] systemd[1]: Listening on Journal Socket (/dev/log).
[    8.002861] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    8.003132] systemd[1]: Listening on Journal Audit Socket.
[    8.003533] systemd[1]: Created slice System Slice.
[    8.036794] systemd[1]: Starting Load Kernel Modules...
[    8.037339] systemd[1]: Created slice User and Session Slice.
[    8.039638] systemd[1]: Mounting POSIX Message Queue File System...
[    8.042217] systemd[1]: Mounting Huge Pages File System...
[    8.042323] systemd[1]: Reached target Slices.
[    8.042703] systemd[1]: Listening on udev Control Socket.
[    8.045294] systemd[1]: Starting Set console keymap...
[    8.046033] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    8.046211] systemd[1]: Reached target Remote File Systems (Pre).
[    8.046323] systemd[1]: Reached target Encrypted Volumes.
[    8.048717] systemd[1]: Starting Uncomplicated firewall...
[    8.051405] systemd[1]: Starting Journal Service...
[    8.053667] systemd[1]: Started Read required files in advance.
[    8.055461] systemd[1]: Reached target Remote File Systems.
[    8.268728] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[    8.271349] systemd[1]: Mounting Debug File System...
[    8.271519] systemd[1]: Reached target User and Group Name Lookups.
[    8.487227] systemd[1]: Started Uncomplicated firewall.
[    8.609371] systemd[1]: Started Create list of required static device nodes for the current kernel.
[    8.628591] systemd[1]: Starting Create Static Device Nodes in /dev...
[    8.739963] systemd[1]: Mounted Huge Pages File System.
[    8.743371] systemd[1]: Mounted POSIX Message Queue File System.
[    8.743471] systemd[1]: Mounted Debug File System.
[    8.929569] lp: driver loaded but no devices found
[    8.978586] ppdev: user-space parallel port driver
[    9.120424] systemd[1]: Started Load Kernel Modules.
[    9.137423] systemd[1]: Starting Apply Kernel Variables...
[    9.139904] systemd[1]: Mounting FUSE Control File System...
[    9.158675] systemd[1]: Mounted FUSE Control File System.
[    9.405293] systemd[1]: Started Journal Service.
[   12.137500] ext4-fs (sda5): re-mounted. Opts: errors=remount-ro
[   13.257432] systemd-journald[205]: Received request to flush runtime journal from PID 1
[   14.273670] intel_rng: FWH not detected
[   14.592668] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   14.976070] atkbd serio0: Unknown key pressed (translated set 2, code 0xf8 on isa0060/serio0).
[   14.976084] atkbd serio0: Use 'setkeycodes e078 <keycode>' to make it known.
[   14.979841] atkbd serio0: Unknown key released (translated set 2, code 0xf8 on isa0060/serio0).
[   14.979854] atkbd serio0: Use 'setkeycodes e078 <keycode>' to make it known.
[   15.078646] leds_ss4200: no LED devices found
[   16.457488] gpio_ich: GPIO from 462 to 511 on gpio_ich
[   16.939848] input: MSI WMI hotkeys as /devices/virtual/input/input8
[   16.986377] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC1200: line_outs=1 (0x1b/0x0/0x0/0x0/0x0) type:speaker
[   16.986393] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   16.986404] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x14/0x0/0x0/0x0/0x0)
[   16.986412] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[   16.986419] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[   16.986429] snd_hda_codec_realtek hdaudioC0D0:      Internal Mic=0x19
[   16.986438] snd_hda_codec_realtek hdaudioC0D0:      Mic=0x18
[   17.004442] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[   17.004959] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   18.462962] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected
[   18.480289] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0003 detected
[   18.745379] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   20.273661] cfg80211: World regulatory domain updated:
[   20.273671] cfg80211:  DFS Master region: unset
[   20.273675] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   20.273683] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   20.273689] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   20.273695] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   20.273701] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   20.273708] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   20.273714] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   20.273720] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   20.273725] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   20.299049] Adding 1036284k swap on /dev/sda6.  Priority:-1 extents:1 across:1036284k FS
[   21.500402] audit: type=1400 audit(1475056097.688:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=596 comm="apparmor_parser"
[   21.500442] audit: type=1400 audit(1475056097.688:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=596 comm="apparmor_parser"
[   21.500471] audit: type=1400 audit(1475056097.688:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=596 comm="apparmor_parser"
[   21.500500] audit: type=1400 audit(1475056097.688:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=596 comm="apparmor_parser"
[   21.699815] audit: type=1400 audit(1475056097.884:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session" pid=595 comm="apparmor_parser"
[   21.699858] audit: type=1400 audit(1475056097.884:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session//chromium" pid=595 comm="apparmor_parser"
[   21.890941] audit: type=1400 audit(1475056098.076:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/snapd/snap-confine" pid=599 comm="apparmor_parser"
[   22.110041] audit: type=1400 audit(1475056098.296:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=600 comm="apparmor_parser"
[   22.110084] audit: type=1400 audit(1475056098.296:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd" pid=600 comm="apparmor_parser"
[   22.110113] audit: type=1400 audit(1475056098.296:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd//third_party" pid=600 comm="apparmor_parser"
[   22.161126] ------------[ cut here ]------------
[   22.161165] WARNING: CPU: 0 PID: 345 at /build/linux-zfJcLg/linux-4.4.0/drivers/gpu/drm/drm_atomic_helper.c:723 drm_atomic_helper_update_legacy_modeset_state+0x26a/0x280 [drm_kms_helper]()
[   22.161170] Modules linked in: arc4 rt2800pci rt2800mmio rt2800lib rt2x00pci rt2x00mmio rt2x00lib mac80211 snd_hda_codec_realtek cfg80211 msi_wmi snd_hda_codec_generic sparse_keymap snd_hda_intel snd_hda_codec snd_hda_core eeprom_93cx6 gpio_ich snd_hwdep crc_ccitt snd_pcm snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device snd_timer coretemp snd soundcore input_leds lpc_ich joydev shpchp serio_raw binfmt_misc mac_hid parport_pc ppdev lp parport autofs4 ums_realtek uas usb_storage i915 psmouse i2c_algo_bit drm_kms_helper r8169 syscopyarea sysfillrect pata_acpi sysimgblt fb_sys_fops drm mii wmi fjes video
[   22.161374] CPU: 0 PID: 345 Comm: plymouthd Tainted: G        W       4.4.0-38-generic #57-Ubuntu
[   22.161379] Hardware name: MULTIRAMA_PC XPRESS BOOK/XPRESS BOOK, BIOS 4.6.3 06/17/2009
[   22.161384]  c1acf967 a122adc2 00000286 f15d3d70 c13a714f 00000000 f85d60f0 f15d3da0
[   22.161397]  c1070307 c19c1d70 00000000 00000159 f85d60f0 000002d3 f85cd94a f85cd94a
[   22.161409]  f5b60000 00000000 f618ca00 f15d3db0 c1070412 00000009 00000000 f15d3dd8
[   22.161421] Call Trace:
[   22.161435]  [<c13a714f>] dump_stack+0x58/0x79
[   22.161445]  [<c1070307>] warn_slowpath_common+0x87/0xc0
[   22.161471]  [<f85cd94a>] ? drm_atomic_helper_update_legacy_modeset_state+0x26a/0x280 [drm_kms_helper]
[   22.161495]  [<f85cd94a>] ? drm_atomic_helper_update_legacy_modeset_state+0x26a/0x280 [drm_kms_helper]
[   22.161503]  [<c1070412>] warn_slowpath_null+0x22/0x30
[   22.161527]  [<f85cd94a>] drm_atomic_helper_update_legacy_modeset_state+0x26a/0x280 [drm_kms_helper]
[   22.161616]  [<f8a08778>] ? intel_pre_plane_update+0xd8/0x130 [i915]
[   22.161698]  [<f8a0916a>] intel_atomic_commit+0x52a/0x6a0 [i915]
[   22.161751]  [<f880147e>] ? drm_atomic_check_only+0x1ae/0x600 [drm]
[   22.161800]  [<f8800119>] ? drm_modeset_lock+0x49/0xd0 [drm]
[   22.161849]  [<f8800a5c>] ? drm_atomic_set_crtc_for_connector+0x5c/0xe0 [drm]
[   22.161899]  [<f8801902>] drm_atomic_commit+0x32/0x60 [drm]
[   22.161924]  [<f85d1633>] restore_fbdev_mode+0x253/0x290 [drm_kms_helper]
[   22.161974]  [<f8800234>] ? drm_modeset_lock_all_ctx+0x94/0xb0 [drm]
[   22.161999]  [<f85d3687>] drm_fb_helper_restore_fbdev_mode_unlocked+0x27/0x70 [drm_kms_helper]
[   22.162081]  [<f8a1e9d0>] intel_fbdev_restore_mode+0x20/0x80 [i915]
[   22.162165]  [<f8a4a92d>] i915_driver_lastclose+0xd/0x20 [i915]
[   22.162210]  [<f87e489a>] drm_lastclose+0x2a/0x140 [drm]
[   22.162254]  [<f87e4c4f>] drm_release+0x29f/0x490 [drm]
[   22.162263]  [<c11a131f>] ? handle_mm_fault+0xb1f/0x11b0
[   22.162270]  [<c11dec5f>] __fput+0xcf/0x210
[   22.162277]  [<c11deddd>] ____fput+0xd/0x10
[   22.162284]  [<c108b49f>] task_work_run+0x7f/0xa0
[   22.162292]  [<c1003115>] exit_to_usermode_loop+0xd5/0xe0
[   22.162299]  [<c10039f7>] do_fast_syscall_32+0x147/0x150
[   22.162307]  [<c17b2b9c>] sysenter_past_esp+0x3d/0x61
[   22.162416] ---[ end trace ba29167eae6f935e ]---
[   37.711977] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   37.721291] r8169 0000:01:00.0 eth0: link down
[   37.721383] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   37.776175] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   37.776463] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
[   37.898873] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.34
[   37.936444] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   38.681038] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   49.143366] usb 1-2: USB disconnect, device number 2
[   82.142247] atkbd serio0: Unknown key pressed (translated set 2, code 0xf6 on isa0060/serio0).
[   82.142267] atkbd serio0: Use 'setkeycodes e076 <keycode>' to make it known.
[   82.147940] atkbd serio0: Unknown key released (translated set 2, code 0xf6 on isa0060/serio0).
[   82.147960] atkbd serio0: Use 'setkeycodes e076 <keycode>' to make it known.
[   89.800190] usb 1-2: new high-speed USB device number 4 using ehci-pci
[   89.933285] usb 1-2: New USB device found, idVendor=2357, idProduct=0108
[   89.933296] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   89.933302] usb 1-2: Product: 802.11n NIC
[   89.933308] usb 1-2: Manufacturer: Realtek
[   89.933314] usb 1-2: SerialNumber: 00e04c000001
[  476.976010] atkbd serio0: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
[  476.976033] atkbd serio0: Use 'setkeycodes e077 <keycode>' to make it known.
[  476.979478] atkbd serio0: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0).
[  476.979495] atkbd serio0: Use 'setkeycodes e077 <keycode>' to make it known.
[  476.986235] atkbd serio0: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
[  476.986256] atkbd serio0: Use 'setkeycodes e077 <keycode>' to make it known.
[  476.989974] atkbd serio0: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0).
[  476.989994] atkbd serio0: Use 'setkeycodes e077 <keycode>' to make it known.
[  498.196611] atkbd serio0: Unknown key pressed (translated set 2, code 0xf8 on isa0060/serio0).
[  498.196631] atkbd serio0: Use 'setkeycodes e078 <keycode>' to make it known.
[  498.199901] atkbd serio0: Unknown key released (translated set 2, code 0xf8 on isa0060/serio0).
[  498.199920] atkbd serio0: Use 'setkeycodes e078 <keycode>' to make it known.
[  498.202727] atkbd serio0: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
[  498.202741] atkbd serio0: Use 'setkeycodes e077 <keycode>' to make it known.
[  498.206441] atkbd serio0: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0).
[  498.206456] atkbd serio0: Use 'setkeycodes e077 <keycode>' to make it known.


το εκανα αλλα τιποτα
dentaltech_13
babeTUX
babeTUX
 
Δημοσιεύσεις: 5
Εγγραφή: 25 Σεπ 2016, 23:55
Εκτύπωση

Re: ΠΡΟΒΛΗΜΑ ΜΕ TP LINK TL-WN822N  Το θέμα επιλύθηκε

Δημοσίευσηαπό Learner » 29 Σεπ 2016, 17:30

Δοκίμασε και τις παρακάτω εντολές, μια-μια

Κώδικας: Επιλογή όλων
git clone https://github.com/jeremyb31/rtl8192eu-linux-driver
cd rtl8192eu-linux-driver
make
sudo make install


Η εντολή make ίσως αργήσει λίγο να ολοκληρωθεί. Δεν πρέπει να επιστρέψει κάποιο error.
Αν οι παραπάνω εντολές ολοκληρωθούν χωρίς λάθη, εκτελείς μετά

Κώδικας: Επιλογή όλων
sudo modprobe -v 8192eu

ή
Κώδικας: Επιλογή όλων
sudo modprobe -v rtl8192eu


Κλείνεις το Internet από το Wireless και έπειτα συνδέεις το USB stick.
Και τα αποτελέσματα της dmesg θα ήταν χρήσιμα.

About Me
Xenial Xerus MuQSS Linux kernel
NickT@Ubuntu

Spoiler: show
1. Ubuntu Xenial (MATE), Arch Linux (GNOME)
2. Intel Core i3 CPU M 380 2.53GHz ‖ RAM 6GB ‖ Acer Aspire 5733
3. Intel Integrated Graphics [8086:0046] {i915}
4. wlan0: Atheros Inc. AR9485 Wireless Network Adapter [168c:0032] (rev 01)
Άβαταρ μέλους
Learner
Συντονιστής
Συντονιστής
 
Δημοσιεύσεις: 9711
Εγγραφή: 08 Νοέμ 2010, 21:24
Τοποθεσία: Αθήνα
Launchpad: NickThom
IRC: NikTh
Εκτύπωση

Re: ΠΡΟΒΛΗΜΑ ΜΕ TP LINK TL-WN822N

Δημοσίευσηαπό dentaltech_13 » 29 Σεπ 2016, 23:08

τα εκανα οπως μου ειπες και επιτελους λειτουργει! 1000 ευχαριστω! ειχα απελπιστει! το dmesg

Κώδικας: Επιλογή όλων
[ 1002.200811] RTL871X: module init start
[ 1002.200828] RTL871X: rtl8192eu v4.3.1.1_11320.20140505
[ 1002.200835] RTL871X: build time: Sep 29 2016 22:34:07
[ 1002.200949] RTL871X:
               usb_endpoint_descriptor(0):
[ 1002.200960] RTL871X: bLength=7
[ 1002.200966] RTL871X: bDescriptorType=5
[ 1002.200973] RTL871X: bEndpointAddress=84
[ 1002.200979] RTL871X: wMaxPacketSize=512
[ 1002.200985] RTL871X: bInterval=0
[ 1002.200992] RTL871X: RT_usb_endpoint_is_bulk_in = 4
[ 1002.200998] RTL871X:
               usb_endpoint_descriptor(1):
[ 1002.201007] RTL871X: bLength=7
[ 1002.201013] RTL871X: bDescriptorType=5
[ 1002.201019] RTL871X: bEndpointAddress=5
[ 1002.201025] RTL871X: wMaxPacketSize=512
[ 1002.201031] RTL871X: bInterval=0
[ 1002.201038] RTL871X: RT_usb_endpoint_is_bulk_out = 5
[ 1002.201045] RTL871X:
               usb_endpoint_descriptor(2):
[ 1002.201053] RTL871X: bLength=7
[ 1002.201059] RTL871X: bDescriptorType=5
[ 1002.201065] RTL871X: bEndpointAddress=6
[ 1002.201071] RTL871X: wMaxPacketSize=512
[ 1002.201077] RTL871X: bInterval=0
[ 1002.201084] RTL871X: RT_usb_endpoint_is_bulk_out = 6
[ 1002.201090] RTL871X:
               usb_endpoint_descriptor(3):
[ 1002.201099] RTL871X: bLength=7
[ 1002.201105] RTL871X: bDescriptorType=5
[ 1002.201111] RTL871X: bEndpointAddress=87
[ 1002.201117] RTL871X: wMaxPacketSize=64
[ 1002.201123] RTL871X: bInterval=3
[ 1002.201130] RTL871X: RT_usb_endpoint_is_int_in = 7, Interval = 3
[ 1002.201136] RTL871X:
               usb_endpoint_descriptor(4):
[ 1002.201145] RTL871X: bLength=7
[ 1002.201151] RTL871X: bDescriptorType=5
[ 1002.201157] RTL871X: bEndpointAddress=8
[ 1002.201163] RTL871X: wMaxPacketSize=512
[ 1002.201169] RTL871X: bInterval=0
[ 1002.201175] RTL871X: RT_usb_endpoint_is_bulk_out = 8
[ 1002.201182] RTL871X: nr_endpoint=5, in_num=2, out_num=3

[ 1002.201191] RTL871X: USB_SPEED_HIGH
[ 1002.201285] RTL871X: CHIP TYPE: RTL8192E
[ 1002.201323] RTL871X: register rtw_netdev_ops to netdev_ops
[ 1002.201739] RTL871X: ReadChipVersion192e 0xF0 = 0xc441135
[ 1002.201756] RTL871X: Chip Version Info: CHIP_8192E_Normal_Chip_SMIC_B_CUT_2T2R_RomVer(0)
[ 1002.201763] RTL871X: RF_Type is 2!!
[ 1002.201772] RTL871X: _ConfigChipOutEP_8192E OutEpQueueSel(0x07), OutEpNumber(3)
[ 1002.201779] RTL871X: ====> ReadAdapterInfo8192EU
[ 1002.201959] RTL871X: Boot from EFUSE, Autoload OK !
[ 1002.355079] RTL871X: EEPROM ID=0x8129
[ 1002.355088] RTL871X: VID = 0x2357, PID = 0x0108
[ 1002.355094] RTL871X: Customer ID: 0x00, SubCustomer ID: 0xCD
[ 1002.355102] RTL871X: hal_ReadMACAddress_8192EU MAC Address from EFUSE = 18:a6:f7:0b:4b:a5
[ 1002.355109] RTL871X: Hal_ReadPowerSavingMode8192E...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(1)
[ 1002.355114] RTL871X: ### PS params=>  power_mgnt(1),usbss_enable(0) ###
[ 1002.355123] RTL871X: EEPROMRegulatory = 0x1 TxPwrCalibrateRate=0x0
[ 1002.355127] RTL871X: Board Type: Dongle or WIFI only Module
[ 1002.355132] RTL871X: mlmepriv.ChannelPlan = 0x21
[ 1002.355137] RTL871X: CrystalCap: 0x3e
[ 1002.355141] RTL871X: ThermalMeter = 0x1c
[ 1002.355146] RTL871X: SWAS: bHwAntDiv = 0, TRxAntDivType = ff
[ 1002.355151] RTL871X: pHalData->PAType_2G is 0x0, pHalData->ExternalPA_2G = 0
[ 1002.355156] RTL871X: pHalData->LNAType_2G is 0x0, pHalData->ExternalLNA_2G = 0
[ 1002.355160] RTL871X: ReadAdapterInfo8192EU <====
[ 1002.355377] RTL871X: init_channel_set ChannelPlan ID 21 Chan num:13 
[ 1002.357242] RTL871X: pwrctrlpriv.bSupportRemoteWakeup~~~~~~
[ 1002.357255] RTL871X: pwrctrlpriv.bSupportRemoteWakeup~~~[1]~~~
[ 1002.357267] RTL871X: can't get autopm:
[ 1002.357281] RTL871X: rtw_macaddr_cfg MAC Address  = 18:a6:f7:0b:4b:a5
[ 1002.357292] RTL871X: bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0
[ 1002.357337] RTL871X: rtw_ndev_init(wlan1)
[ 1002.362500] RTL871X: _rtw_drv_register_netdev, MAC Address (if1) = 18:a6:f7:0b:4b:a5
[ 1002.363921] RTL871X: LeaveAllPowerSaveMode(wlan1): bup=0 Skip!
[ 1002.363935] RTL871X: rtw_wx_set_scan: bDriverStopped=1, bup=0, hw_init_completed=0
[ 1002.371163] usbcore: registered new interface driver rtl8192eu
[ 1002.371177] RTL871X: module init ret=0
[ 1002.421962] rtl8192eu 1-2:1.0 enx18a6f70b4ba5: renamed from wlan1
[ 1002.802219] IPv6: ADDRCONF(NETDEV_UP): enx18a6f70b4ba5: link is not ready
[ 1023.564698] atkbd serio0: Unknown key pressed (translated set 2, code 0xf6 on isa0060/serio0).
[ 1023.564718] atkbd serio0: Use 'setkeycodes e076 <keycode>' to make it known.
[ 1023.568538] atkbd serio0: Unknown key released (translated set 2, code 0xf6 on isa0060/serio0).
[ 1023.568556] atkbd serio0: Use 'setkeycodes e076 <keycode>' to make it known.
[ 1024.048472] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1024.194980] RTL871X: +871x_drv - drv_open, bup=0
[ 1024.194991] RTL871X: ==>_InitPowerOn_8192EU
[ 1024.198945] RTL871X: SetHwReg8192E: bMacPwrCtrlOn=1
[ 1024.199561] RTL871X:  ===> FirmwareDownload88E() fw source from Header.
[ 1024.199569] RTL871X: FirmwareDownload8192E fw:NIC, size: 31818
[ 1024.199574] RTL871X: FirmwareDownload8192E: fw_ver=19 fw_subver=0 sig=0x92e1
[ 1024.229943] RTL871X: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00070305
[ 1024.231308] RTL871X: =====> _8051Reset8192E(): 8051 reset success .
[ 1024.255820] RTL871X: _FWFreeToGo8192E: Polling FW ready OK! (189, 24ms), REG_MCUFWDL:0x000702c6
[ 1024.255828] RTL871X: FWDL success. write_fw:1, 52ms
[ 1024.269189] RTL871X: ===> phy_BB8192E_Config_ParaFile() EEPROMRegulatory 1
[ 1024.311942] RTL871X: PHY_BBConfig8192E ==> CrystalCap:0x3e
[ 1024.923813] RTL871X: Auto InitLLTTable8192E success
[ 1024.957189] RTL871X: pDM_Odm TxPowerTrackControl = 1
[ 1025.192792] RTL871X: phy_SpurCalibration_8192E =>AFE_PHASE_SEL
[ 1025.256088] RTL871X: ===FixSpur NOT Pass!
[ 1025.655646] RTL871X: enx18a6f70b4ba5 MAC Address from REG_MACID = 18:a6:f7:0b:4b:a5
[ 1025.655656] RTL871X: rtl8192eu_hal_init in 1460ms
[ 1025.655664] RTL871X: enx18a6f70b4ba5Port-0  set opmode = 2
[ 1025.674898] RTL871X: MAC Address = 18:a6:f7:0b:4b:a5
[ 1025.675064] RTL871X: -871x_drv - drv_open, bup=1
[ 1025.675228] IPv6: ADDRCONF(NETDEV_UP): enx18a6f70b4ba5: link is not ready
[ 1025.817141] RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
[ 1025.817163] RTL871X: set_mode = IW_MODE_INFRA
[ 1025.818926] RTL871X: set bssid:00:00:00:00:00:00
[ 1025.819041] RTL871X: =>rtw_wx_set_essid
[ 1025.819049] RTL871X: ssid=g\xffffffc6isQ\xffffffffJ\xffffffec)ͺ\xffffffab\xfffffff2\xfffffffb\xffffffe3F|\xffffffc2T\xfffffff8xffffffe8\xffffffe7\xffffff8dvZ.c3\xffffff9fɚ)H\xfffffff7, len=32
[ 1025.819060] RTL871X: set ssid [g\xffffffc6isQ\xffffffffJ\xffffffec)ͺ\xffffffab\xfffffff2\xfffffffb\xffffffe3F|\xffffffc2T\xfffffff8xffffffe8\xffffffe7\xffffff8dvZ.c3\xffffff9fɚx\xffffffed*\xffffff98^\xffffff87\xfffffff2] fw_state=0x00000008
[ 1025.819065] RTL871X: Set SSID under fw_state=0x00000008
[ 1025.819081] RTL871X: <=rtw_wx_set_essid, ret 0
[ 1025.826204] RTL871X: enx18a6f70b4ba5Port-0  set opmode = 2
[ 1025.840797] RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
[ 1025.874331] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1025.914566] IPv6: ADDRCONF(NETDEV_UP): enx18a6f70b4ba5: link is not ready
[ 1027.384992] wlan0: authenticate with 58:98:35:8c:54:c5
[ 1027.392240] wlan0: send auth to 58:98:35:8c:54:c5 (try 1/3)
[ 1027.397207] wlan0: authenticated
[ 1027.400098] wlan0: associate with 58:98:35:8c:54:c5 (try 1/3)
[ 1027.403859] wlan0: RX AssocResp from 58:98:35:8c:54:c5 (capab=0x411 status=0 aid=7)
[ 1027.403977] wlan0: associated
[ 1027.404164] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1027.409474] RTL871X: survey done event(3c) band:0 for enx18a6f70b4ba5
[ 1027.409501] RTL871X: rtw_select_and_join_from_scanned_queue: return _FAIL(candidate == NULL)
[ 1027.409510] RTL871X: try_to_join, but select scanning queue fail, to_roam:0
[ 1027.409517] RTL871X: indicate disassoc
[ 1027.409550] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 1027.409630] RTL871X: +rtl8192e_set_FwJoinBssReport_cmd(enx18a6f70b4ba5): iface_type=0 mstatus(0)
[ 1027.413453] RTL871X: ==>rtw_ps_processor .fw_state(8)
[ 1027.413464] RTL871X: ==>ips_enter cnts:1
[ 1027.413469] RTL871X: nolinked power save enter
[ 1027.413474] RTL871X: ===> rtw_ips_pwr_down...................
[ 1027.413480] RTL871X: ====> rtw_ips_dev_unload...
[ 1027.439405] RTL871X: usb_read_port_cancel
[ 1027.439698] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1027.444223] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1027.444448] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1027.444692] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1027.444941] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1027.445191] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1027.445446] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1027.445697] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1027.446430] RTL871X: usb_write_port_cancel
[ 1027.446507] RTL871X: ==> rtl8192eu_hal_deinit
[ 1027.447337] RTL871X: bkeepfwalive(0)
[ 1027.447349] RTL871X:  hal_poweroff_8192eu
[ 1027.452338] RTL871X: SetHwReg8192E: bMacPwrCtrlOn=0
[ 1027.452349] RTL871X: <=== rtw_ips_pwr_down..................... in 40ms
[ 1029.003936] RTL871X: _rtw_pwr_wakeup call ips_leave....
[ 1029.003949] RTL871X: ==>ips_leave cnts:1
[ 1029.003955] RTL871X: ===>  rtw_ips_pwr_up..............
[ 1029.003972] RTL871X: ===> ips_netdrv_open.........
[ 1029.003980] RTL871X: ==>_InitPowerOn_8192EU
[ 1029.011413] RTL871X: SetHwReg8192E: bMacPwrCtrlOn=1
[ 1029.013915] RTL871X:  ===> FirmwareDownload88E() fw source from Header.
[ 1029.013930] RTL871X: FirmwareDownload8192E fw:NIC, size: 31818
[ 1029.013938] RTL871X: FirmwareDownload8192E: fw_ver=19 fw_subver=0 sig=0x92e1
[ 1029.048163] RTL871X: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00070605
[ 1029.049528] RTL871X: =====> _8051Reset8192E(): 8051 reset success .
[ 1029.074034] RTL871X: _FWFreeToGo8192E: Polling FW ready OK! (164, 24ms), REG_MCUFWDL:0x000706c6
[ 1029.074046] RTL871X: FWDL success. write_fw:1, 60ms
[ 1029.087786] RTL871X: ===> phy_BB8192E_Config_ParaFile() EEPROMRegulatory 1
[ 1029.140046] RTL871X: PHY_BBConfig8192E ==> CrystalCap:0x3e
[ 1029.751385] RTL871X: Auto InitLLTTable8192E success
[ 1029.784052] RTL871X: pDM_Odm TxPowerTrackControl = 1
[ 1030.027254] RTL871X: phy_SpurCalibration_8192E =>AFE_PHASE_SEL
[ 1030.091286] RTL871X: ===FixSpur NOT Pass!
[ 1030.495864] RTL871X: enx18a6f70b4ba5 MAC Address from REG_MACID = 18:a6:f7:0b:4b:a5
[ 1030.495876] RTL871X: rtl8192eu_hal_init in 1492ms
[ 1030.495888] RTL871X: enx18a6f70b4ba5Port-0  set opmode = 2
[ 1030.521644] RTL871X: <===  rtw_ips_pwr_up.............. in 1520ms
[ 1030.521655] RTL871X: nolinked power save leave
[ 1030.521723] RTL871X: ==> ips_leave.....LED(0x0f620282)...
[ 1032.063331] RTL871X: survey done event(4d) band:0 for enx18a6f70b4ba5
[ 1032.063357] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 1032.064536] RTL871X: ==>rtw_ps_processor .fw_state(8)
[ 1032.064545] RTL871X: ==>ips_enter cnts:2
[ 1032.064550] RTL871X: nolinked power save enter
[ 1032.064555] RTL871X: ===> rtw_ips_pwr_down...................
[ 1032.064561] RTL871X: ====> rtw_ips_dev_unload...
[ 1032.095354] RTL871X: usb_read_port_cancel
[ 1032.100293] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1032.100538] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1032.100783] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1032.101037] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1032.101283] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1032.101531] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1032.101788] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1032.102031] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1032.102058] RTL871X: usb_write_port_cancel
[ 1032.102126] RTL871X: ==> rtl8192eu_hal_deinit
[ 1032.102924] RTL871X: bkeepfwalive(0)
[ 1032.102935] RTL871X:  hal_poweroff_8192eu
[ 1032.107926] RTL871X: SetHwReg8192E: bMacPwrCtrlOn=0
[ 1032.107938] RTL871X: <=== rtw_ips_pwr_down..................... in 40ms
[ 1052.017516] RTL871X: _rtw_pwr_wakeup call ips_leave....
[ 1052.017531] RTL871X: ==>ips_leave cnts:2
[ 1052.017537] RTL871X: ===>  rtw_ips_pwr_up..............
[ 1052.017553] RTL871X: ===> ips_netdrv_open.........
[ 1052.017560] RTL871X: ==>_InitPowerOn_8192EU
[ 1052.023601] RTL871X: SetHwReg8192E: bMacPwrCtrlOn=1
[ 1052.024617] RTL871X:  ===> FirmwareDownload88E() fw source from Header.
[ 1052.024627] RTL871X: FirmwareDownload8192E fw:NIC, size: 31818
[ 1052.024633] RTL871X: FirmwareDownload8192E: fw_ver=19 fw_subver=0 sig=0x92e1
[ 1052.054986] RTL871X: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00070605
[ 1052.056751] RTL871X: =====> _8051Reset8192E(): 8051 reset success .
[ 1052.081231] RTL871X: _FWFreeToGo8192E: Polling FW ready OK! (191, 28ms), REG_MCUFWDL:0x000706c6
[ 1052.081244] RTL871X: FWDL success. write_fw:1, 56ms
[ 1052.095109] RTL871X: ===> phy_BB8192E_Config_ParaFile() EEPROMRegulatory 1
[ 1052.138973] RTL871X: PHY_BBConfig8192E ==> CrystalCap:0x3e
[ 1052.508116] ieee80211 phy0: rt2x00queue_flush_queue: Warning - Queue 1 failed to flush
[ 1052.668201] ieee80211 phy0: rt2x00queue_flush_queue: Warning - Queue 2 failed to flush
[ 1052.751594] RTL871X: Auto InitLLTTable8192E success
[ 1052.784327] RTL871X: pDM_Odm TxPowerTrackControl = 1
[ 1053.148319] RTL871X: phy_SpurCalibration_8192E =>AFE_PHASE_SEL
[ 1053.211444] RTL871X: ===FixSpur NOT Pass!
[ 1053.337331] RTL871X: === PathA=1, PathB=1
[ 1053.337341] RTL871X: ===FixSpur Pass!
[ 1053.363311] RTL871X: enx18a6f70b4ba5 MAC Address from REG_MACID = 18:a6:f7:0b:4b:a5
[ 1053.363323] RTL871X: rtl8192eu_hal_init in 1344ms
[ 1053.363334] RTL871X: enx18a6f70b4ba5Port-0  set opmode = 2
[ 1053.383459] RTL871X: <===  rtw_ips_pwr_up.............. in 1364ms
[ 1053.383468] RTL871X: nolinked power save leave
[ 1053.383559] RTL871X: ==> ips_leave.....LED(0x0f620282)...
[ 1054.476109] ieee80211 phy0: rt2x00queue_flush_queue: Warning - Queue 1 failed to flush
[ 1054.918756] RTL871X: survey done event(1f) band:0 for enx18a6f70b4ba5
[ 1054.918779] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 1054.922979] RTL871X: ==>rtw_ps_processor .fw_state(8)
[ 1054.922996] RTL871X: ==>ips_enter cnts:3
[ 1054.923004] RTL871X: nolinked power save enter
[ 1054.923012] RTL871X: ===> rtw_ips_pwr_down...................
[ 1054.923021] RTL871X: ====> rtw_ips_dev_unload...
[ 1054.953925] RTL871X: usb_read_port_cancel
[ 1054.960244] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1054.960476] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1054.960730] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1054.960979] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1054.961230] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1054.961481] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1054.961728] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1054.961976] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1054.962004] RTL871X: usb_write_port_cancel
[ 1054.962077] RTL871X: ==> rtl8192eu_hal_deinit
[ 1054.962869] RTL871X: bkeepfwalive(0)
[ 1054.962880] RTL871X:  hal_poweroff_8192eu
[ 1054.968999] RTL871X: SetHwReg8192E: bMacPwrCtrlOn=0
[ 1054.969012] RTL871X: <=== rtw_ips_pwr_down..................... in 48ms
[ 1079.575686] wlan0: deauthenticating from 58:98:35:8c:54:c5 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 1079.635224] cfg80211: World regulatory domain updated:
[ 1079.635237] cfg80211:  DFS Master region: unset
[ 1079.635243] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 1079.635252] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 1079.635261] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 1079.635269] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 1079.635278] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 1079.635364] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 1079.635373] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 1079.635381] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 1079.635389] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 1085.003916] RTL871X: _rtw_pwr_wakeup call ips_leave....
[ 1085.003928] RTL871X: ==>ips_leave cnts:3
[ 1085.003934] RTL871X: ===>  rtw_ips_pwr_up..............
[ 1085.003950] RTL871X: ===> ips_netdrv_open.........
[ 1085.003957] RTL871X: ==>_InitPowerOn_8192EU
[ 1085.009180] RTL871X: SetHwReg8192E: bMacPwrCtrlOn=1
[ 1085.009796] RTL871X:  ===> FirmwareDownload88E() fw source from Header.
[ 1085.009808] RTL871X: FirmwareDownload8192E fw:NIC, size: 31818
[ 1085.009816] RTL871X: FirmwareDownload8192E: fw_ver=19 fw_subver=0 sig=0x92e1
[ 1085.038931] RTL871X: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00070605
[ 1085.040926] RTL871X: =====> _8051Reset8192E(): 8051 reset success .
[ 1085.065425] RTL871X: _FWFreeToGo8192E: Polling FW ready OK! (183, 28ms), REG_MCUFWDL:0x000706c6
[ 1085.065436] RTL871X: FWDL success. write_fw:1, 56ms
[ 1085.079798] RTL871X: ===> phy_BB8192E_Config_ParaFile() EEPROMRegulatory 1
[ 1085.140425] RTL871X: PHY_BBConfig8192E ==> CrystalCap:0x3e
[ 1085.751291] RTL871X: Auto InitLLTTable8192E success
[ 1085.783657] RTL871X: pDM_Odm TxPowerTrackControl = 1
[ 1086.022018] RTL871X: phy_SpurCalibration_8192E =>AFE_PHASE_SEL
[ 1086.085809] RTL871X: ===FixSpur NOT Pass!
[ 1086.462134] RTL871X: === PathA=1, PathB=1
[ 1086.462142] RTL871X: ===FixSpur Pass!
[ 1086.487373] RTL871X: enx18a6f70b4ba5 MAC Address from REG_MACID = 18:a6:f7:0b:4b:a5
[ 1086.487382] RTL871X: rtl8192eu_hal_init in 1484ms
[ 1086.487391] RTL871X: enx18a6f70b4ba5Port-0  set opmode = 2
[ 1086.507018] RTL871X: <===  rtw_ips_pwr_up.............. in 1504ms
[ 1086.507026] RTL871X: nolinked power save leave
[ 1086.507109] RTL871X: ==> ips_leave.....LED(0x0f620282)...
[ 1088.043212] RTL871X: survey done event(2a) band:0 for enx18a6f70b4ba5
[ 1088.043242] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 1088.045356] RTL871X: ==>rtw_ps_processor .fw_state(8)
[ 1088.045372] RTL871X: ==>ips_enter cnts:4
[ 1088.045382] RTL871X: nolinked power save enter
[ 1088.045392] RTL871X: ===> rtw_ips_pwr_down...................
[ 1088.045403] RTL871X: ====> rtw_ips_dev_unload...
[ 1088.083493] RTL871X: usb_read_port_cancel
[ 1088.088315] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1088.088552] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1088.088801] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1088.089047] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1088.089304] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1088.089547] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1088.089796] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1088.090051] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1088.090084] RTL871X: usb_write_port_cancel
[ 1088.090154] RTL871X: ==> rtl8192eu_hal_deinit
[ 1088.090941] RTL871X: bkeepfwalive(0)
[ 1088.090953] RTL871X:  hal_poweroff_8192eu
[ 1088.097442] RTL871X: SetHwReg8192E: bMacPwrCtrlOn=0
[ 1088.097455] RTL871X: <=== rtw_ips_pwr_down..................... in 52ms
[ 1143.186873] RTL871X: _rtw_pwr_wakeup call ips_leave....
[ 1143.186887] RTL871X: ==>ips_leave cnts:4
[ 1143.186894] RTL871X: ===>  rtw_ips_pwr_up..............
[ 1143.186910] RTL871X: ===> ips_netdrv_open.........
[ 1143.186919] RTL871X: ==>_InitPowerOn_8192EU
[ 1143.191864] RTL871X: SetHwReg8192E: bMacPwrCtrlOn=1
[ 1143.192861] RTL871X:  ===> FirmwareDownload88E() fw source from Header.
[ 1143.192875] RTL871X: FirmwareDownload8192E fw:NIC, size: 31818
[ 1143.192884] RTL871X: FirmwareDownload8192E: fw_ver=19 fw_subver=0 sig=0x92e1
[ 1143.228363] RTL871X: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00070605
[ 1143.229718] RTL871X: =====> _8051Reset8192E(): 8051 reset success .
[ 1143.254233] RTL871X: _FWFreeToGo8192E: Polling FW ready OK! (176, 24ms), REG_MCUFWDL:0x000706c6
[ 1143.254244] RTL871X: FWDL success. write_fw:1, 60ms
[ 1143.267477] RTL871X: ===> phy_BB8192E_Config_ParaFile() EEPROMRegulatory 1
[ 1143.310354] RTL871X: PHY_BBConfig8192E ==> CrystalCap:0x3e
[ 1143.923337] RTL871X: Auto InitLLTTable8192E success
[ 1143.959475] RTL871X: pDM_Odm TxPowerTrackControl = 1
[ 1144.200942] RTL871X: phy_SpurCalibration_8192E =>AFE_PHASE_SEL
[ 1144.264584] RTL871X: ===FixSpur NOT Pass!
[ 1144.453106] RTL871X: === PathA=1, PathB=1
[ 1144.453117] RTL871X: ===FixSpur Pass!
[ 1144.479328] RTL871X: enx18a6f70b4ba5 MAC Address from REG_MACID = 18:a6:f7:0b:4b:a5
[ 1144.479344] RTL871X: rtl8192eu_hal_init in 1292ms
[ 1144.479359] RTL871X: enx18a6f70b4ba5Port-0  set opmode = 2
[ 1144.500218] RTL871X: <===  rtw_ips_pwr_up.............. in 1316ms
[ 1144.500228] RTL871X: nolinked power save leave
[ 1144.500302] RTL871X: ==> ips_leave.....LED(0x0f620282)...
[ 1146.051134] RTL871X: survey done event(3e) band:0 for enx18a6f70b4ba5
[ 1146.051162] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 1146.052586] RTL871X: ==>rtw_ps_processor .fw_state(8)
[ 1146.052597] RTL871X: ==>ips_enter cnts:5
[ 1146.052602] RTL871X: nolinked power save enter
[ 1146.052608] RTL871X: ===> rtw_ips_pwr_down...................
[ 1146.052614] RTL871X: ====> rtw_ips_dev_unload...
[ 1146.078133] RTL871X: wpa_set_auth_algs, AUTH_ALG_OPEN_SYSTEM
[ 1146.078155] RTL871X: _rtw_pwr_wakeup wait ps_processing...
[ 1146.092679] RTL871X: usb_read_port_cancel
[ 1146.092983] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1146.093225] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1146.093475] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1146.093724] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1146.093973] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1146.094227] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1146.094475] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1146.094724] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0)
[ 1146.094747] RTL871X: usb_write_port_cancel
[ 1146.094814] RTL871X: ==> rtl8192eu_hal_deinit
[ 1146.095614] RTL871X: bkeepfwalive(0)
[ 1146.095623] RTL871X:  hal_poweroff_8192eu
[ 1146.101873] RTL871X: SetHwReg8192E: bMacPwrCtrlOn=0
[ 1146.101886] RTL871X: <=== rtw_ips_pwr_down..................... in 48ms
[ 1146.114007] RTL871X: _rtw_pwr_wakeup wait ps_processing done
[ 1146.114021] RTL871X: _rtw_pwr_wakeup call ips_leave....
[ 1146.114029] RTL871X: ==>ips_leave cnts:5
[ 1146.114035] RTL871X: ===>  rtw_ips_pwr_up..............
[ 1146.114050] RTL871X: ===> ips_netdrv_open.........
[ 1146.114057] RTL871X: ==>_InitPowerOn_8192EU
[ 1146.118871] RTL871X: SetHwReg8192E: bMacPwrCtrlOn=1
[ 1146.119492] RTL871X:  ===> FirmwareDownload88E() fw source from Header.
[ 1146.119503] RTL871X: FirmwareDownload8192E fw:NIC, size: 31818
[ 1146.119512] RTL871X: FirmwareDownload8192E: fw_ver=19 fw_subver=0 sig=0x92e1
[ 1146.157128] RTL871X: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00070605
[ 1146.158495] RTL871X: =====> _8051Reset8192E(): 8051 reset success .
[ 1146.183528] RTL871X: _FWFreeToGo8192E: Polling FW ready OK! (116, 24ms), REG_MCUFWDL:0x000706c6
[ 1146.183540] RTL871X: FWDL success. write_fw:1, 60ms
[ 1146.196745] RTL871X: ===> phy_BB8192E_Config_ParaFile() EEPROMRegulatory 1
[ 1146.245003] RTL871X: PHY_BBConfig8192E ==> CrystalCap:0x3e
[ 1146.887361] RTL871X: Auto InitLLTTable8192E success
[ 1146.919365] RTL871X: pDM_Odm TxPowerTrackControl = 1
[ 1147.156963] RTL871X: phy_SpurCalibration_8192E =>AFE_PHASE_SEL
[ 1147.219971] RTL871X: ===FixSpur NOT Pass!
[ 1147.412238] RTL871X: === PathA=1, PathB=1
[ 1147.412251] RTL871X: ===FixSpur Pass!
[ 1147.437326] RTL871X: enx18a6f70b4ba5 MAC Address from REG_MACID = 18:a6:f7:0b:4b:a5
[ 1147.437336] RTL871X: rtl8192eu_hal_init in 1324ms
[ 1147.437345] RTL871X: enx18a6f70b4ba5Port-0  set opmode = 2
[ 1147.462361] RTL871X: <===  rtw_ips_pwr_up.............. in 1348ms
[ 1147.462371] RTL871X: nolinked power save leave
[ 1147.462445] RTL871X: ==> ips_leave.....LED(0x0f620282)...
[ 1147.462453] RTL871X: set_mode = IW_MODE_INFRA
[ 1147.462498] RTL871X: enx18a6f70b4ba5Port-0  set opmode = 2
[ 1147.463159] RTL871X:
                wpa_ie(length:22):
[ 1147.463212] RTL871X: 0x30 0x14 0x01 0x00 0x00 0x0f 0xac 0x02
[ 1147.463221] RTL871X: 0x01 0x00 0x00 0x0f 0xac 0x04 0x01 0x00
[ 1147.463229] RTL871X: 0x00 0x0f 0xac 0x02 0x00 0x00 0x00 0x00
[ 1147.464951] RTL871X: SetHwReg8192E, 4457, RCR= 700060ca
[ 1147.465103] RTL871X: =>rtw_wx_set_essid
[ 1147.465111] RTL871X: ssid=nea folia, len=9
[ 1147.465135] RTL871X: set ssid [nea folia] fw_state=0x00000008
[ 1147.465141] RTL871X: Set SSID under fw_state=0x00000008
[ 1147.465156] RTL871X: [by_bssid:0][assoc_ssid:nea folia][to_roam:0] new candidate: nea folia(04:bf:6d:95:cc:90, ch13) rssi:-82
[ 1147.465167] RTL871X: rtw_select_and_join_from_scanned_queue: candidate: nea folia(04:bf:6d:95:cc:90, ch:13)
[ 1147.465181] RTL871X: [HT] Support STBC = 0x01
[ 1147.465187] RTL871X: declare supporting RX STBC
[ 1147.465198] RTL871X: link to Ralink AP
[ 1147.465208] RTL871X: <=rtw_wx_set_essid, ret 0
[ 1147.465329] RTL871X: start_join_set_ch_bw: ch=13, bwmode=0, ch_offset=0
[ 1147.465356] RTL871X: set bssid:04:bf:6d:95:cc:90
[ 1147.465363] RTL871X: Set BSSID under fw_state=0x00000088
[ 1149.941494] RTL871X: link to Ralink AP
[ 1149.941512] RTL871X: start auth
[ 1149.941528] RTL871X: issue_auth
[ 1149.950173] RTL871X: OnAuthClient
[ 1149.950241] RTL871X: auth success, start assoc
[ 1149.950285] RTL871X: network.SupportedRates[0]=82
[ 1149.950310] RTL871X: network.SupportedRates[1]=84
[ 1149.950326] RTL871X: network.SupportedRates[2]=8B
[ 1149.950358] RTL871X: network.SupportedRates[3]=96
[ 1149.950374] RTL871X: network.SupportedRates[4]=12
[ 1149.950389] RTL871X: network.SupportedRates[5]=24
[ 1149.950405] RTL871X: network.SupportedRates[6]=48
[ 1149.950420] RTL871X: network.SupportedRates[7]=6C
[ 1149.950436] RTL871X: network.SupportedRates[8]=0C
[ 1149.950452] RTL871X: network.SupportedRates[9]=18
[ 1149.950468] RTL871X: network.SupportedRates[10]=30
[ 1149.950484] RTL871X: network.SupportedRates[11]=60
[ 1149.950501] RTL871X: bssrate_len = 12
[ 1149.959036] RTL871X: OnAssocRsp
[ 1149.959124] RTL871X: report_join_res(6)
[ 1149.959167] RTL871X: rtw_joinbss_update_network
[ 1149.959193] RTL871X: +rtw_update_ht_cap()
[ 1149.959252] RTL871X: rtw_alloc_macid = 0
[ 1149.959271] RTL871X: rtw_joinbss_update_stainfo
[ 1149.959298] RTL871X: ### Set STA_(0) info
[ 1149.959318] RTL871X: assoc success
[ 1149.959417] RTL871X: SetHwReg8192E(enx18a6f70b4ba5) HW_VAR_BASIC_RATE: BrateCfg(0x15d)
[ 1149.959534] IPv6: ADDRCONF(NETDEV_CHANGE): enx18a6f70b4ba5: link becomes ready
[ 1149.964999] RTL871X: WMM(0): 0, a42b
[ 1149.965114] RTL871X: WMM(1): 0, a44f
[ 1149.965252] RTL871X: WMM(2): 0, 5e4322
[ 1149.965373] RTL871X: WMM(3): 0, 2f3222
[ 1149.965385] RTL871X: wmm_para_seq(0): 0
[ 1149.965393] RTL871X: wmm_para_seq(1): 1
[ 1149.965402] RTL871X: wmm_para_seq(2): 2
[ 1149.965411] RTL871X: wmm_para_seq(3): 3
[ 1149.965420] RTL871X: HTOnAssocRsp
[ 1149.989366] RTL871X: UpdateHalRAMask8192E => mac_id:0, networkType:0x0b, mask:0x000fffff
                   ==> rssi_level:0, rate_bitmap:0x000ff005
[ 1149.989382] RTL871X: rtl8192e_set_raid_cmd, bitmap=0xff005, mac_id=0x0, raid=0x3, shortGIrate=1
[ 1149.991616] RTL871X: ### rtl8192e_set_FwMediaStatus_cmd: MStatus=1 MACID=0
[ 1149.994111] RTL871X: +rtl8192e_set_FwJoinBssReport_cmd(enx18a6f70b4ba5): iface_type=0 mstatus(1)
[ 1149.995477] RTL871X: SetFwRsvdPagePkt
[ 1149.995500] RTL871X: ConstructProbeRsp FW Mac Addr:18:a6:f7:0b:4b:a5
[ 1149.995509] RTL871X: ConstructProbeRsp FW IP Addr4.191.109.149
[ 1149.995731] RTL871X: SetFwRsvdPagePkt: Set RSVD page location to Fw ,TotalPacketLen(1866), PageNum(8)
[ 1149.997868] RTL871X: enx18a6f70b4ba5: 1 DL RSVD page success! DLBcnCount:1, poll:1
[ 1149.998601] RTL871X: Set RSVD page location to Fw.
[ 1149.998728] RTL871X: =>mlmeext_joinbss_event_callback
[ 1150.914069] RTL871X: send eapol packet
[ 1150.920870] RTL871X: OnAction_back
[ 1150.920880] RTL871X: OnAction_back, action=0
[ 1150.920886] RTL871X: issue_action_BA, category=3, action=1, status=0
[ 1150.921288] RTL871X: send eapol packet
[ 1150.921361] RTL871X:  ~~~~set sta key:unicastkey
[ 1150.921640] RTL871X:  ~~~~set sta key:groupkey
[ 1150.921651] RTL871X: ==> rtw_set_key algorithm(2),keyid(2),key_mask(0)
[ 1150.922365] RTL871X: set pairwise key to hw: alg:4(WEP40-1 WEP104-5 TKIP-2 AES-4) camid:4
[ 1150.924711] RTL871X: set group key to hw: alg:2(WEP40-1 WEP104-5 TKIP-2 AES-4) keyid:2
[ 1150.926587] RTL871X: SetHwReg8192E, 4452, RCR= 700060ce
[ 1151.474694] RTL871X: UpdateHalRAMask8192E => mac_id:0, networkType:0x0b, mask:0x000fffff
                   ==> rssi_level:3, rate_bitmap:0x000ff005
[ 1151.474709] RTL871X: rtl8192e_set_raid_cmd, bitmap=0xff005, mac_id=0x0, raid=0x3, shortGIrate=1
[ 1155.997943] RTL871X: OnAction_back
[ 1155.998016] RTL871X: OnAction_back, action=0
[ 1155.998040] RTL871X: issue_action_BA, category=3, action=1, status=0
[ 1165.496436] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1165.498278] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1169.504404] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1169.504426] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1171.508483] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1171.508505] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1173.512384] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1173.512406] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1177.520366] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1177.520380] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1179.524418] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1179.524440] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1182.584741] RTL871X: survey done event(2b) band:0 for enx18a6f70b4ba5
[ 1182.584810] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 1187.540386] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1187.540407] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1224.008488] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-LPS_CTRL_LEAVE
[ 1224.008506] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1225.596927] RTL871X: survey done event(3c) band:0 for enx18a6f70b4ba5
[ 1225.596986] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 1235.636509] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1235.636531] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1245.656436] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1245.656459] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1247.660379] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1247.660401] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1263.692409] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1263.692425] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1269.704412] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1269.704434] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1275.716365] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1275.716382] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1278.913171] RTL871X: rtw_issue_addbareq_cmd, p=0
[ 1278.913236] RTL871X: issue_action_BA, category=3, action=0, status=0
[ 1278.913249] RTL871X: BA_starting_seqctrl = 404 for TID=0
[ 1278.917215] RTL871X: OnAction_back
[ 1278.917229] RTL871X: OnAction_back, action=1
[ 1278.917235] RTL871X: agg_enable for TID=0
[ 1288.618726] RTL871X: survey done event(42) band:0 for enx18a6f70b4ba5
[ 1288.618751] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 1291.748461] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1291.748482] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1295.756522] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1295.756535] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1299.764678] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1299.764695] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1311.788422] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1311.788435] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1313.792489] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1313.792511] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1337.840385] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1337.840398] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1341.848484] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1341.848506] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1370.008796] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-LPS_CTRL_LEAVE
[ 1370.008821] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1371.598649] RTL871X: survey done event(55) band:0 for enx18a6f70b4ba5
[ 1371.598681] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 1371.908385] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1371.908403] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1395.956407] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1395.956429] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1397.960479] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1397.960512] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1456.076487] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1456.076510] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1458.080542] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1458.080563] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1460.084463] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1460.084485] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1464.092455] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1464.092478] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1473.029177] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-LPS_CTRL_LEAVE
[ 1473.029194] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1474.632766] RTL871X: survey done event(2f) band:0 for enx18a6f70b4ba5
[ 1474.632788] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 1478.120495] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1478.120517] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1496.156564] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1496.156587] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1498.160474] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1498.160497] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1500.164383] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1500.164404] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1504.172462] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1504.172484] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1593.025608] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-LPS_CTRL_LEAVE
[ 1593.025625] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1594.644804] RTL871X: survey done event(2f) band:0 for enx18a6f70b4ba5
[ 1594.644822] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 1596.356473] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1596.356495] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1597.620096] usb 1-1: new high-speed USB device number 4 using ehci-pci
[ 1597.753966] usb 1-1: New USB device found, idVendor=0421, idProduct=0301
[ 1597.753986] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1597.753999] usb 1-1: Product: N8-00
[ 1597.754011] usb 1-1: Manufacturer: Nokia
[ 1597.754022] usb 1-1: SerialNumber: 351661057651352
[ 1597.762218] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 1597.767420] scsi host3: usb-storage 1-1:1.0
[ 1598.765965] scsi 3:0:0:0: Direct-Access                                    PQ: 0 ANSI: 0
[ 1598.767184] scsi 3:0:0:1: Direct-Access                                    PQ: 0 ANSI: 0
[ 1598.772389] sd 3:0:0:0: Attached scsi generic sg1 type 0
[ 1598.775243] sd 3:0:0:0: [sdb] 29990912 512-byte logical blocks: (15.4 GB/14.3 GiB)
[ 1598.775799] sd 3:0:0:1: Attached scsi generic sg2 type 0
[ 1598.775870] sd 3:0:0:0: [sdb] Write Protect is off
[ 1598.775883] sd 3:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 1598.779368] sd 3:0:0:0: [sdb] No Caching mode page found
[ 1598.779384] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 1598.785317] sd 3:0:0:1: [sdc] 3970048 512-byte logical blocks: (2.03 GB/1.89 GiB)
[ 1598.786022] sd 3:0:0:1: [sdc] Write Protect is off
[ 1598.786060] sd 3:0:0:1: [sdc] Mode Sense: 03 00 00 00
[ 1598.787169] sd 3:0:0:1: [sdc] No Caching mode page found
[ 1598.787188] sd 3:0:0:1: [sdc] Assuming drive cache: write through
[ 1598.791518]  sdb:
[ 1598.800248] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[ 1598.802451]  sdc: sdc1
[ 1598.807390] sd 3:0:0:1: [sdc] Attached SCSI removable disk
[ 1600.317364] FAT-fs (sdb): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 1622.408425] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1622.408442] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1628.420411] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1628.420426] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1660.484368] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1660.484385] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1662.488510] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1662.488527] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1664.492534] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1664.492555] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1670.504391] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1670.504408] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1684.532435] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1684.532458] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1686.536419] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1686.536433] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1696.556453] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1696.556476] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1698.560400] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1698.560417] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1713.033082] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-LPS_CTRL_LEAVE
[ 1713.033100] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1714.620716] RTL871X: survey done event(34) band:0 for enx18a6f70b4ba5
[ 1714.620734] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 1716.596494] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1716.596517] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1726.616481] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1726.616503] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1728.620470] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1728.620491] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1740.644865] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1740.644883] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1794.769292] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1794.769314] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1802.768442] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1802.768470] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1806.776514] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1806.776535] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1828.820481] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1828.820503] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1830.824332] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1830.824355] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1833.025091] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-LPS_CTRL_LEAVE
[ 1833.025109] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1834.612738] RTL871X: survey done event(48) band:0 for enx18a6f70b4ba5
[ 1834.612780] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 1834.832369] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1834.832387] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1864.892582] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1864.892603] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1868.906984] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1868.906998] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1888.940415] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1888.940438] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1890.944494] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1890.944509] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1892.948473] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1892.948496] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1894.952435] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1894.952457] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1900.964433] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1900.964452] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1904.972473] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1904.972491] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1925.012529] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1925.012550] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1927.016484] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1927.016507] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1947.056393] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1947.056406] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1949.066891] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1949.066930] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1951.064423] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1951.064445] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1954.617555] RTL871X: survey done event(32) band:0 for enx18a6f70b4ba5
[ 1954.617578] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 1955.072352] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1955.072373] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1961.084439] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1961.084462] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1963.088394] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1963.088417] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1965.092475] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1965.092496] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1967.096420] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1967.096443] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 1989.140515] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 1989.140536] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 1993.148540] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 1993.148569] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2012.684197] atkbd serio0: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
[ 2012.684217] atkbd serio0: Use 'setkeycodes e077 <keycode>' to make it known.
[ 2012.688155] atkbd serio0: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0).
[ 2012.688175] atkbd serio0: Use 'setkeycodes e077 <keycode>' to make it known.
[ 2012.694227] atkbd serio0: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
[ 2012.694257] atkbd serio0: Use 'setkeycodes e077 <keycode>' to make it known.
[ 2012.697771] atkbd serio0: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0).
[ 2012.697784] atkbd serio0: Use 'setkeycodes e077 <keycode>' to make it known.
[ 2025.212482] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 2025.212503] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 2027.216455] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 2027.216477] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2045.252625] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 2045.252646] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 2047.256430] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 2047.256452] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2073.027581] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-LPS_CTRL_LEAVE
[ 2073.027598] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 2074.636943] RTL871X: survey done event(50) band:0 for enx18a6f70b4ba5
[ 2074.636971] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 2075.312423] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 2075.312440] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2078.128218] [Firmware Bug]: battery: (dis)charge rate invalid.
[ 2079.130502] atkbd serio0: Unknown key pressed (translated set 2, code 0xf8 on isa0060/serio0).
[ 2079.130514] atkbd serio0: Use 'setkeycodes e078 <keycode>' to make it known.
[ 2079.135621] atkbd serio0: Unknown key released (translated set 2, code 0xf8 on isa0060/serio0).
[ 2079.135636] atkbd serio0: Use 'setkeycodes e078 <keycode>' to make it known.
[ 2079.140215] atkbd serio0: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
[ 2079.140229] atkbd serio0: Use 'setkeycodes e077 <keycode>' to make it known.
[ 2079.143800] atkbd serio0: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0).
[ 2079.143817] atkbd serio0: Use 'setkeycodes e077 <keycode>' to make it known.
[ 2093.348448] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 2093.348464] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 2095.352390] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 2095.352407] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2101.326466] usb 1-1: USB disconnect, device number 4
[ 2109.380419] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 2109.380439] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 2111.384487] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 2111.384509] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2151.464400] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 2151.464416] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 2159.480394] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 2159.480411] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2163.488415] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 2163.488432] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 2171.504463] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 2171.504486] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2175.512479] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 2175.512502] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 2177.516412] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 2177.516427] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2185.532427] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 2185.532444] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 2194.616410] RTL871X: survey done event(52) band:0 for enx18a6f70b4ba5
[ 2194.616481] RTL871X: rtw_indicate_scan_done(enx18a6f70b4ba5)
[ 2201.564350] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 2201.564366] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2209.580376] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 2209.580394] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 2213.588384] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 2213.588400] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2215.592464] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 2215.592482] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 2217.596409] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 2217.596431] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2219.600617] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 2219.600638] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 2225.612417] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 2225.612434] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2227.616361] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 2227.616377] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 2235.632539] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 2235.632555] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2243.648421] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 2243.648442] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 2245.652604] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 2245.652626] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2251.664506] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 2251.664527] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
[ 2253.668436] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Enter 802.11 power save - WIFI-TRAFFIC_IDLE
[ 2253.668459] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=1 SmartPS=2 UAPSD=0
[ 2291.744468] RTL871X: rtw_set_ps_mode(enx18a6f70b4ba5) Leave 802.11 power save - WIFI-TRAFFIC_BUSY
[ 2291.744490] RTL871X: rtl8192e_set_FwPwrMode_cmd: Mode=0 SmartPS=2 UAPSD=0
dentaltech_13
babeTUX
babeTUX
 
Δημοσιεύσεις: 5
Εγγραφή: 25 Σεπ 2016, 23:55
Εκτύπωση

Re: ΠΡΟΒΛΗΜΑ ΜΕ TP LINK TL-WN822N

Δημοσίευσηαπό Learner » 01 Οκτ 2016, 15:18

dentaltech_13 έγραψε:τα εκανα οπως μου ειπες και επιτελους λειτουργει! 1000 ευχαριστω!

Μετά από αναβάθμιση του πυρήνα πιθανό είναι να μη λειτουργεί. Τότε, θα πρέπει να τρέξεις πάλι τις εντολές σε αυτό ποστ για να λειτουργήσει ξανά.
Το module αυτό το εισήγαγες εσύ στον πυρήνα με τις παραπάνω εντολές. Έτσι, όταν γίνει αναβάθμιση σε νεότερη έκδοση πυρήνα αυτό το module δεν θα υπάρχει, θα πρέπει να το εισάγεις εκ νέου.

Υπάρχει μια αυτόματη διαδικασία μέσω dkms (dynamic kernel module support). Αν ολοκληρωθεί με επιτυχία, τότε το module θα το χτίζει αυτόματα το πακέτο dkms χωρίς να χρειάζεται να το κάνεις χειροκίνητα.

Ακολούθησε τη παρακάτω διαδικασία
Κώδικας: Επιλογή όλων
cd rtl8192eu-linux-driver
gedit dkms.conf

Στη κενή σελίδα που θα ανοίξει πρόσθεσε μέσα τα παρακάτω
Κώδικας: Επιλογή όλων
PACKAGE_NAME=8192eu
PACKAGE_VERSION=4.3
MAKE[0]="'make' KVER=${kernelver}"
BUILT_MODULE_NAME[0]=8192eu
BUILT_MODULE_LOCATION[0]="./"
DEST_MODULE_LOCATION[0]="/kernel/updates/dkms"
AUTOINSTALL="YES"


Αποθήκευσε το αρχείο και μετά τρέξε στο τερματικό
Κώδικας: Επιλογή όλων
cd
sudo dkms add ./rtl8192eu-linux-driver
sudo dkms install -m 8192eu -v 4.3

Τυχόν λάθη (errors) δημοσίευσε τα εδώ.

About Me
Xenial Xerus MuQSS Linux kernel
NickT@Ubuntu

Spoiler: show
1. Ubuntu Xenial (MATE), Arch Linux (GNOME)
2. Intel Core i3 CPU M 380 2.53GHz ‖ RAM 6GB ‖ Acer Aspire 5733
3. Intel Integrated Graphics [8086:0046] {i915}
4. wlan0: Atheros Inc. AR9485 Wireless Network Adapter [168c:0032] (rev 01)
Άβαταρ μέλους
Learner
Συντονιστής
Συντονιστής
 
Δημοσιεύσεις: 9711
Εγγραφή: 08 Νοέμ 2010, 21:24
Τοποθεσία: Αθήνα
Launchpad: NickThom
IRC: NikTh
Εκτύπωση

Re: ΠΡΟΒΛΗΜΑ ΜΕ TP LINK TL-WN822N

Δημοσίευσηαπό hgf » 09 Οκτ 2016, 14:29

Καλησπερα σας.
ΘΈΛΩ ΝΑ ΡΩΤΗΣΩ ΝΑ ΜΟΥ ΠΕΙ ΚΑΠΟΙΟΣ ΠΩΣ ΜΠΟΡΩ ΝΑ ΕΛΕΓΞΩ ΑΝ Ο ΠΥΡΗΝΑΣ ΤΗΣ ΔΙΑΝΟΜΗΣ ΜΟΥ ΕΧΕΙ Η ΔΕΝ ΕΧΕΙ ΕΝΑ ΣΥΓΚΕΚΡΙΜΕΝΟ module;
και επισης πως μπορω να βρω ποιο ειναι το καταληλο module μιας πχ ασυρματης καρτας;(για να τσεκαρω αν το εχει ο πυρηνας)
ΕΥΧΑΡΙΣΤΩ
1 Γνώσεις Linux: Πρώτα βήματα ┃ Προγραμματισμού: Πρώτα βήματα ┃ Αγγλικών: Πρώτα βήματα
2 Ubuntu 12.04 precise 32bit (el_GR.UTF-8), Windows NT/2000/XP, Microsoft Windows XP Professional, Ubuntu 3.4.0-030400rc4-generic
3 Intel Pentium Dual CPU E2200 2.20GHz ‖ RAM 2003 MiB ‖ ECS G31T-M5 - NEC COMPUTERS SAS 00000000000000000000000
4 Intel 82G33/G31 Express Integrated Graphics Controller [8086:29c2] (rev 10)
5 eth0: Realtek RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01)
hgf
dudeTUX
dudeTUX
 
Δημοσιεύσεις: 379
Εγγραφή: 15 Νοέμ 2011, 11:03
Εκτύπωση

Επόμενο

  • ΣΧΕΤΙΚΑ ΘΕΜΑΤΑ
    ΑΠΑΝΤΗΣΕΙΣ
    ΠΡΟΒΟΛΕΣ
    ΣΥΓΓΡΑΦΕΑΣ

Επιστροφή στο Κάρτες Δικτύου (Ethernet, WiFi, Bluetooth) / Internet

Μέλη σε σύνδεση

Μέλη σε αυτή τη Δ. Συζήτηση: Δεν υπάρχουν εγγεγραμμένα μέλη και 2 επισκέπτες