the_eye έγραψε:1. Πόσες usb συσκευές έχεις ; Δοκίμασε να bootάρεις χωρίς τίποτα στο usb, μετά να συνδέσεις μία μόνο συσκευή και δώσε μας τότε το dmesg.
2. Δες στο bios αν το IOMMU Controller είναι ενεργοποιημένο.
6usb + 2 usb 3 εκανα boot χωρίς καμιά συσκευή και σύνδεσα μόνο πληκτρολόγιο και ποντίκι μετά
- Κώδικας: Επιλογή όλων
[ 3.310081] hub 3-0:1.0: USB hub found
[ 3.310083] hub 3-0:1.0: 4 ports detected
[ 3.310156] ehci-platform: EHCI generic platform driver
[ 3.310163] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.310164] ohci-pci: OHCI PCI platform driver
[ 3.310233] ohci-pci 0000:00:12.0: OHCI PCI host controller
[ 3.310238] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 4
[ 3.310256] ohci-pci 0000:00:12.0: irq 18, io mem 0xfe40a000
[ 3.370049] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.370052] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.370053] usb usb4: Product: OHCI PCI host controller
[ 3.370054] usb usb4: Manufacturer: Linux 3.11.0-15-generic ohci_hcd
[ 3.370055] usb usb4: SerialNumber: 0000:00:12.0
[ 3.370150] hub 4-0:1.0: USB hub found
[ 3.370155] hub 4-0:1.0: 5 ports detected
[ 3.370288] ohci-pci 0000:00:13.0: OHCI PCI host controller
[ 3.370292] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5
[ 3.370306] ohci-pci 0000:00:13.0: irq 18, io mem 0xfe408000
[ 3.430037] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.430039] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.430041] usb usb5: Product: OHCI PCI host controller
[ 3.430042] usb usb5: Manufacturer: Linux 3.11.0-15-generic ohci_hcd
[ 3.430043] usb usb5: SerialNumber: 0000:00:13.0
[ 3.430136] hub 5-0:1.0: USB hub found
[ 3.430141] hub 5-0:1.0: 5 ports detected
[ 3.430270] ohci-pci 0000:00:14.5: OHCI PCI host controller
[ 3.430275] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 6
[ 3.430287] ohci-pci 0000:00:14.5: irq 18, io mem 0xfe406000
[ 3.490077] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.490079] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.490081] usb usb6: Product: OHCI PCI host controller
[ 3.490082] usb usb6: Manufacturer: Linux 3.11.0-15-generic ohci_hcd
[ 3.490083] usb usb6: SerialNumber: 0000:00:14.5
[ 3.490176] hub 6-0:1.0: USB hub found
[ 3.490180] hub 6-0:1.0: 2 ports detected
[ 3.490291] ohci-pci 0000:00:16.0: OHCI PCI host controller
[ 3.490295] ohci-pci 0000:00:16.0: new USB bus registered, assigned bus number 7
[ 3.490307] ohci-pci 0000:00:16.0: irq 18, io mem 0xfe405000
[ 3.550117] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.550119] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.550120] usb usb7: Product: OHCI PCI host controller
[ 3.550122] usb usb7: Manufacturer: Linux 3.11.0-15-generic ohci_hcd
[ 3.550123] usb usb7: SerialNumber: 0000:00:16.0
[ 3.550218] hub 7-0:1.0: USB hub found
[ 3.550222] hub 7-0:1.0: 4 ports detected
[ 3.550288] ohci-platform: OHCI generic platform driver
[ 3.550295] uhci_hcd: USB Universal Host Controller Interface driver
[ 3.550356] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 3.550360] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 8
[ 3.550447] xhci_hcd 0000:02:00.0: irq 72 for MSI/MSI-X
[ 3.550484] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.550485] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.550486] usb usb8: Product: xHCI Host Controller
[ 3.550487] usb usb8: Manufacturer: Linux 3.11.0-15-generic xhci_hcd
[ 3.550489] usb usb8: SerialNumber: 0000:02:00.0
[ 3.550536] xHCI xhci_add_endpoint called for root hub
[ 3.550537] xHCI xhci_check_bandwidth called for root hub
[ 3.550550] hub 8-0:1.0: USB hub found
[ 3.550554] hub 8-0:1.0: 2 ports detected
[ 3.550598] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 3.550601] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 9
[ 3.550616] usb usb9: New USB device found, idVendor=1d6b, idProduct=0003
[ 3.550618] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.550620] usb usb9: Product: xHCI Host Controller
[ 3.550621] usb usb9: Manufacturer: Linux 3.11.0-15-generic xhci_hcd
[ 3.550622] usb usb9: SerialNumber: 0000:02:00.0
[ 3.550667] xHCI xhci_add_endpoint called for root hub
[ 3.550667] xHCI xhci_check_bandwidth called for root hub
[ 3.550679] hub 9-0:1.0: USB hub found
[ 3.550683] hub 9-0:1.0: 2 ports detected
[ 3.558217] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 3.558223] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 10
[ 3.558307] xhci_hcd 0000:04:00.0: irq 73 for MSI/MSI-X
[ 3.558347] usb usb10: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.558349] usb usb10: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.558350] usb usb10: Product: xHCI Host Controller
[ 3.558351] usb usb10: Manufacturer: Linux 3.11.0-15-generic xhci_hcd
[ 3.558352] usb usb10: SerialNumber: 0000:04:00.0
[ 3.558421] xHCI xhci_add_endpoint called for root hub
[ 3.558423] xHCI xhci_check_bandwidth called for root hub
[ 3.558437] hub 10-0:1.0: USB hub found
[ 3.558441] hub 10-0:1.0: 2 ports detected
[ 3.558486] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 3.558489] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 11
[ 3.558503] usb usb11: New USB device found, idVendor=1d6b, idProduct=0003
[ 3.558504] usb usb11: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.558505] usb usb11: Product: xHCI Host Controller
[ 3.558507] usb usb11: Manufacturer: Linux 3.11.0-15-generic xhci_hcd
[ 3.558508] usb usb11: SerialNumber: 0000:04:00.0
[ 3.558551] xHCI xhci_add_endpoint called for root hub
[ 3.558552] xHCI xhci_check_bandwidth called for root hub
[ 3.558566] hub 11-0:1.0: USB hub found
[ 3.558570] hub 11-0:1.0: 2 ports detected
[ 3.566214] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 3.566546] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.566550] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 3.566630] mousedev: PS/2 mouse device common for all mice
[ 3.566742] rtc_cmos 00:05: RTC can wake from S4
[ 3.566830] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 3.566849] rtc_cmos 00:05: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 3.566892] device-mapper: uevent: version 1.0.3
[ 3.566938] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: dm-devel@redhat.com
[ 3.566991] cpuidle: using governor ladder
[ 3.566992] cpuidle: using governor menu
[ 3.567001] ledtrig-cpu: registered to indicate activity on CPUs
[ 3.567057] TCP: cubic registered
[ 3.567118] NET: Registered protocol family 10
[ 3.567253] NET: Registered protocol family 17
[ 3.567261] Key type dns_resolver registered
[ 3.567469] PM: Hibernation image not present or could not be loaded.
[ 3.567471] Loading module verification certificates
[ 3.568211] MODSIGN: Loaded cert 'Magrathea: Glacier signing key: e20ade5b3af83aaa8563f0ef4119a030c4d3ffdb'
[ 3.568222] registered taskstats version 1
[ 3.569852] Key type trusted registered
[ 3.571106] Key type encrypted registered
[ 3.572366] AppArmor: AppArmor sha1 policy hashing enabled
[ 3.572606] Magic number: 6:888:550
[ 3.572619] tty ttyS26: hash matches
[ 3.572625] clockevents clockevent1: hash matches
[ 3.572641] acpi PNP0C0F:01: hash matches
[ 3.572683] rtc_cmos 00:05: setting system clock to 2014-03-16 21:31:30 UTC (1395005490)
[ 3.572767] acpi-cpufreq: overriding BIOS provided _PSD data
[ 3.572862] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 3.572862] EDD information not available.
[ 3.574044] Freeing unused kernel memory: 1392K (ffffffff81d0f000 - ffffffff81e6b000)
[ 3.574046] Write protecting the kernel read-only data: 12288k
[ 3.575515] Freeing unused kernel memory: 672K (ffff880001758000 - ffff880001800000)
[ 3.575573] Freeing unused kernel memory: 20K (ffff880001bfb000 - ffff880001c00000)
[ 3.589060] udevd[121]: starting version 175
[ 3.607515] wmi: Mapper loaded
[ 3.614059] ahci 0000:00:11.0: version 3.0
[ 3.614254] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 6 ports 6 Gbps 0x3f impl SATA mode
[ 3.614257] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
[ 3.615539] scsi0 : ahci
[ 3.616681] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 3.616692] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 3.616894] r8169 0000:03:00.0: irq 74 for MSI/MSI-X
[ 3.617031] r8169 0000:03:00.0 eth0: RTL8168evl/8111evl at 0xffffc9000064e000, 94:de:80:78:2a:2d, XID 0c900800 IRQ 74
[ 3.617033] r8169 0000:03:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 3.617048] scsi1 : ahci
[ 3.617332] scsi2 : ahci
[ 3.617454] scsi3 : ahci
[ 3.617657] scsi4 : ahci
[ 3.618644] scsi5 : ahci
[ 3.618699] ata1: SATA max UDMA/133 abar m1024@0xfe40b000 port 0xfe40b100 irq 19
[ 3.618701] ata2: SATA max UDMA/133 abar m1024@0xfe40b000 port 0xfe40b180 irq 19
[ 3.618703] ata3: SATA max UDMA/133 abar m1024@0xfe40b000 port 0xfe40b200 irq 19
[ 3.618705] ata4: SATA max UDMA/133 abar m1024@0xfe40b000 port 0xfe40b280 irq 19
[ 3.618707] ata5: SATA max UDMA/133 abar m1024@0xfe40b000 port 0xfe40b300 irq 19
[ 3.618709] ata6: SATA max UDMA/133 abar m1024@0xfe40b000 port 0xfe40b380 irq 19
[ 3.621912] [drm] Initialized drm 1.1.0 20060810
[ 3.636777] MXM: GUID detected in BIOS
[ 3.637049] nouveau [ DEVICE][0000:01:00.0] BOOT0 : 0x0e6020a1
[ 3.637052] nouveau [ DEVICE][0000:01:00.0] Chipset: GK106 (NVE6)
[ 3.637054] nouveau [ DEVICE][0000:01:00.0] Family : NVE0
[ 3.637630] nouveau [ VBIOS][0000:01:00.0] checking PRAMIN for image...
[ 3.637636] nouveau [ VBIOS][0000:01:00.0] ... signature not found
[ 3.637637] nouveau [ VBIOS][0000:01:00.0] checking PROM for image...
[ 3.748792] nouveau [ VBIOS][0000:01:00.0] ... appears to be valid
[ 3.748793] nouveau [ VBIOS][0000:01:00.0] using image from PROM
[ 3.748898] nouveau [ VBIOS][0000:01:00.0] BIT signature found
[ 3.748901] nouveau [ VBIOS][0000:01:00.0] version 80.06.59.00.1a
[ 3.749186] nouveau [ PFB][0000:01:00.0] RAM type: GDDR5
[ 3.749188] nouveau [ PFB][0000:01:00.0] RAM size: 2048 MiB
[ 3.749189] nouveau [ PFB][0000:01:00.0] ZCOMP: 0 tags
[ 3.771354] nouveau [ PTHERM][0000:01:00.0] FAN control: none / external
[ 3.771359] nouveau [ PTHERM][0000:01:00.0] fan management: disabled
[ 3.771361] nouveau [ PTHERM][0000:01:00.0] internal sensor: yes
[ 3.785958] [TTM] Zone kernel: Available graphics memory: 2044616 kiB
[ 3.785959] [TTM] Initializing pool allocator
[ 3.785962] [TTM] Initializing DMA pool allocator
[ 3.785968] nouveau [ DRM] VRAM: 2048 MiB
[ 3.785970] nouveau [ DRM] GART: 1048576 MiB
[ 3.785972] nouveau [ DRM] TMDS table version 2.0
[ 3.785974] nouveau [ DRM] DCB version 4.0
[ 3.785975] nouveau [ DRM] DCB outp 00: 02000f00 00000000
[ 3.785977] nouveau [ DRM] DCB outp 01: 01000f02 00020030
[ 3.785978] nouveau [ DRM] DCB outp 03: 02011f62 00020010
[ 3.785980] nouveau [ DRM] DCB outp 04: 04822fb6 0f420010
[ 3.785981] nouveau [ DRM] DCB outp 05: 04022f72 00020010
[ 3.785982] nouveau [ DRM] DCB outp 06: 08033f82 00020030
[ 3.785984] nouveau [ DRM] DCB conn 00: 00001030
[ 3.785985] nouveau [ DRM] DCB conn 01: 00010161
[ 3.785987] nouveau [ DRM] DCB conn 02: 00020246
[ 3.785988] nouveau [ DRM] DCB conn 03: 01000331
[ 3.786983] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 3.786984] [drm] No driver support for vblank timestamp query.
[ 3.787036] nouveau W[ DRM] voltage table 0x50 unknown
[ 3.787040] nouveau [ DRM] 4 available performance level(s)
[ 3.787043] nouveau [ DRM] 0: core 162MHz shader 324MHz memory 648MHz voltage 100mV
[ 3.787045] nouveau [ DRM] 1: core 405MHz shader 810MHz memory 1080MHz voltage 80mV
[ 3.787047] nouveau [ DRM] 2: core 1502MHz shader 3004MHz memory 1080MHz voltage 60mV
[ 3.787049] nouveau [ DRM] 3: core 1502MHz shader 3004MHz memory 1080MHz voltage 40mV
[ 3.787050] nouveau [ DRM] c:
[ 3.796287] nouveau [ DRM] MM: using COPY for buffer copies
[ 3.842325] firewire_ohci 0000:05:0e.0: added OHCI v1.10 device as card 0, 4 IR + 8 IT contexts, quirks 0x11
[ 3.937310] nouveau [ DRM] allocated 1280x1024 fb: 0x80000, bo ffff8801278b4000
[ 3.937374] fbcon: nouveaufb (fb0) is primary device
[ 3.942380] ata5: SATA link down (SStatus 0 SControl 300)
[ 3.942412] ata2: SATA link down (SStatus 0 SControl 300)
[ 3.942442] ata6: SATA link down (SStatus 0 SControl 300)
[ 3.942472] ata3: SATA link down (SStatus 0 SControl 300)
[ 4.018414] Console: switching to colour frame buffer device 160x64
[ 4.019428] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
[ 4.019429] nouveau 0000:01:00.0: registered panic notifier
[ 4.019432] [drm] Initialized nouveau 1.1.1 20120801 for 0000:01:00.0 on minor 0
[ 4.114483] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.116131] ata4.00: ATAPI: Optiarc DVD RW AD-5260S, 1.00, max UDMA/100
[ 4.118420] ata4.00: configured for UDMA/100
[ 4.125229] xor: measuring software checksum speed
[ 4.162476] prefetch64-sse: 13298.000 MB/sec
[ 4.202502] generic_sse: 12883.000 MB/sec
[ 4.202503] xor: using function: prefetch64-sse (13298.000 MB/sec)
[ 4.226548] tsc: Refined TSC clocksource calibration: 3415.597 MHz
[ 4.270561] raid6: sse2x1 4443 MB/s
[ 4.338603] raid6: sse2x2 7348 MB/s
[ 4.406653] raid6: sse2x4 8400 MB/s
[ 4.406654] raid6: using algorithm sse2x4 (8400 MB/s)
[ 4.406655] raid6: using intx1 recovery algorithm
[ 4.416951] bio: create slab <bio-1> at 1
[ 4.417233] Btrfs loaded
[ 4.424863] device-mapper: dm-raid45: initialized v0.2594b
[ 4.450792] firewire_core 0000:05:0e.0: created device fw0: GUID 0049e550e5d20b00, S400
[ 4.842996] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.843595] ata1.00: ATA-7: Maxtor 6Y120M0, YAR51EW0, max UDMA/133
[ 4.843597] ata1.00: 240121728 sectors, multi 0: LBA
[ 4.844288] ata1.00: configured for UDMA/133
[ 4.844447] scsi 0:0:0:0: Direct-Access ATA Maxtor 6Y120M0 YAR5 PQ: 0 ANSI: 5
[ 4.844608] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.844610] sd 0:0:0:0: [sda] 240121728 512-byte logical blocks: (122 GB/114 GiB)
[ 4.844678] sd 0:0:0:0: [sda] Write Protect is off
[ 4.844681] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.844704] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.846460] scsi 3:0:0:0: CD-ROM Optiarc DVD RW AD-5260S 1.00 PQ: 0 ANSI: 5
[ 4.848906] sr0: scsi3-mmc drive: 94x/94x writer cd/rw xa/form2 cdda tray
[ 4.848909] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 4.849007] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 4.849124] sr 3:0:0:0: Attached scsi generic sg1 type 5
[ 4.908360] sda: sda1 sda4 < sda5 sda6 sda7 >
[ 4.908795] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.227318] Switched to clocksource tsc
[ 6.345362] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[ 6.496590] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
[ 7.140423] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 7.142879] ISO 9660 Extensions: RRIP_1991A
[ 7.503345] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 41.541068] Adding 3070968k swap on /dev/sda6. Priority:-1 extents:1 across:3070968k FS
[ 41.814162] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 41.974237] udevd[1362]: starting version 175
[ 45.215483] device-mapper: multipath: version 1.5.1 loaded
[ 46.362940] MCE: In-kernel MCE decoding enabled.
[ 46.363674] lp: driver loaded but no devices found
[ 46.451432] EDAC MC: Ver: 3.0.0
[ 46.673577] AMD64 EDAC driver v3.4.0
[ 46.673603] EDAC amd64: DRAM ECC disabled.
[ 46.673608] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
[ 46.673608] Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
[ 46.673608] (Note that use of the override may cause unknown side effects.)
[ 46.773448] Bluetooth: Core ver 2.16
[ 46.773469] NET: Registered protocol family 31
[ 46.773470] Bluetooth: HCI device and connection manager initialized
[ 46.773478] Bluetooth: HCI socket layer initialized
[ 46.773479] Bluetooth: L2CAP socket layer initialized
[ 46.773485] Bluetooth: SCO socket layer initialized
[ 46.861329] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 47.104909] ppdev: user-space parallel port driver
[ 47.106092] Bluetooth: RFCOMM TTY layer initialized
[ 47.106102] Bluetooth: RFCOMM socket layer initialized
[ 47.106104] Bluetooth: RFCOMM ver 1.11
[ 47.395538] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05
[ 47.395591] sp5100_tco: PCI Revision ID: 0x42
[ 47.395874] sp5100_tco: Using 0xfed80b00 for watchdog MMIO address
[ 47.395884] sp5100_tco: Last reboot was not triggered by watchdog.
[ 47.395946] sp5100_tco: initialized (0xffffc900107ceb00). heartbeat=60 sec (nowayout=0)
[ 47.515044] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 47.515047] Bluetooth: BNEP filters: protocol multicast
[ 47.515054] Bluetooth: BNEP socket layer initialized
[ 49.074270] init: failsafe main process (1566) killed by TERM signal
[ 51.202753] hda-intel 0000:00:14.2: Using LPIB position fix
[ 51.206206] hda-intel 0000:00:14.2: Enable sync_write for stable communication
[ 51.534009] SKU: Nid=0x1d sku_cfg=0x4005e601
[ 51.534011] SKU: port_connectivity=0x1
[ 51.534012] SKU: enable_pcbeep=0x0
[ 51.534013] SKU: check_sum=0x00000005
[ 51.534014] SKU: customization=0x000000e6
[ 51.534015] SKU: external_amp=0x0
[ 51.534015] SKU: platform_type=0x0
[ 51.534016] SKU: swap=0x0
[ 51.534017] SKU: override=0x1
[ 51.534452] autoconfig: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[ 51.534453] speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 51.534454] hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 51.534455] mono: mono_out=0x0
[ 51.534456] dig-out=0x11/0x1e
[ 51.534457] inputs:
[ 51.534458] Front Mic=0x19
[ 51.534459] Rear Mic=0x18
[ 51.534460] Line=0x1a
[ 51.534461] realtek: No valid SSID, checking pincfg 0x4005e601 for NID 0x1d
[ 51.534462] realtek: Enabling init ASM_ID=0xe601 CODEC_ID=10ec0889
[ 51.548628] input: HDA ATI SB Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input2
[ 51.548703] input: HDA ATI SB Line Out Side as /devices/pci0000:00/0000:00:14.2/sound/card0/input3
[ 51.548755] input: HDA ATI SB Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card0/input4
[ 51.548802] input: HDA ATI SB Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card0/input5
[ 51.548850] input: HDA ATI SB Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card0/input6
[ 51.548896] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input7
[ 51.548943] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input8
[ 51.548990] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input9
[ 51.549248] hda_intel: Disabling MSI
[ 51.549258] hda-intel 0000:01:00.1: Handle VGA-switcheroo audio client
[ 51.549287] hda-intel 0000:01:00.1: Disabling 64bit DMA
[ 51.552337] hda-intel 0000:01:00.1: Enable delay in RIRB handling
[ 52.298512] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input10
[ 52.298580] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input11
[ 52.298648] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input12
[ 52.298698] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input13
[ 56.454042] init: alsa-restore main process (1838) terminated with status 99
[ 58.320448] r8169 0000:03:00.0 eth0: link down
[ 58.320491] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 58.320695] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 84.956084] usb 7-2: new full-speed USB device number 2 using ohci-pci
[ 85.096180] usb 7-2: device descriptor read/64, error -32
[ 85.340331] usb 7-2: device descriptor read/64, error -32
[ 85.580493] usb 7-2: new full-speed USB device number 3 using ohci-pci
[ 85.724591] usb 7-2: device descriptor read/64, error -32
[ 85.968762] usb 7-2: device descriptor read/64, error -32
[ 86.209198] usb 7-2: new full-speed USB device number 4 using ohci-pci
[ 86.617178] usb 7-2: device not accepting address 4, error -32
[ 86.757274] usb 7-2: new full-speed USB device number 5 using ohci-pci
[ 87.165513] usb 7-2: device not accepting address 5, error -32
[ 87.165527] hub 7-0:1.0: unable to enumerate USB device on port 2
[ 95.214871] usb 7-2: new full-speed USB device number 6 using ohci-pci
[ 95.354978] usb 7-2: device descriptor read/64, error -32
[ 95.599150] usb 7-2: device descriptor read/64, error -32
[ 95.839298] usb 7-2: new full-speed USB device number 7 using ohci-pci
[ 95.979391] usb 7-2: device descriptor read/64, error -32
[ 96.223551] usb 7-2: device descriptor read/64, error -32
[ 96.463689] usb 7-2: new full-speed USB device number 8 using ohci-pci
[ 96.871982] usb 7-2: device not accepting address 8, error -32
[ 97.008074] usb 7-2: new full-speed USB device number 9 using ohci-pci
[ 97.416349] usb 7-2: device not accepting address 9, error -32
[ 97.416382] hub 7-0:1.0: unable to enumerate USB device on port 2
[ 97.628487] usb 7-2: new full-speed USB device number 10 using ohci-pci
[ 97.768561] usb 7-2: device descriptor read/64, error -32
[ 98.012750] usb 7-2: device descriptor read/64, error -32
[ 98.252899] usb 7-2: new full-speed USB device number 11 using ohci-pci
[ 98.392989] usb 7-2: device descriptor read/64, error -32
[ 98.637152] usb 7-2: device descriptor read/64, error -32
[ 98.877311] usb 7-2: new full-speed USB device number 12 using ohci-pci
[ 99.285580] usb 7-2: device not accepting address 12, error -32
[ 99.421633] usb 7-2: new full-speed USB device number 13 using ohci-pci
[ 99.829941] usb 7-2: device not accepting address 13, error -32
[ 99.829976] hub 7-0:1.0: unable to enumerate USB device on port 2
[ 100.042098] usb 7-2: new full-speed USB device number 14 using ohci-pci
[ 100.182131] usb 7-2: device descriptor read/64, error -32
[ 100.426340] usb 7-2: device descriptor read/64, error -32
[ 100.666497] usb 7-2: new full-speed USB device number 15 using ohci-pci
[ 102.123476] usb 8-2: new full-speed USB device number 2 using xhci_hcd
[ 102.178337] usb 8-2: New USB device found, idVendor=045e, idProduct=0724
[ 102.178341] usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 102.178343] usb 8-2: Product: SideWinder\xffffffe2\xffffff84\xffffffa2\xffffff84\xffffffa2 Mouse
[ 102.178345] usb 8-2: Manufacturer: Microsoft
[ 102.466090] hidraw: raw HID events driver (C) Jiri Kosina
[ 102.765790] usbcore: registered new interface driver usbhid
[ 102.765793] usbhid: USB HID core driver
[ 102.947918] input: Microsoft SideWinder\xffffffe2\xffffff84\xffffffa2\xffffff84\xffffffa2 Mouse as /devices/pci0000:00/0000:00:04.0/0000:02:00.0/usb8/8-2/8-2:1.0/input/input14
[ 102.948706] hid-generic 0003:045E:0724.0001: input,hidraw0: USB HID v1.11 Mouse [Microsoft SideWinder\xffffffe2\xffffff84\xffffffa2\xffffff84\xffffffa2 Mouse] on usb-0000:02:00.0-2/input0
[ 118.504574] usb 8-2: USB disconnect, device number 2
[ 121.192105] usb 7-2: new full-speed USB device number 16 using ohci-pci
[ 121.361293] usb 7-2: unable to read config index 0 descriptor/start: -32
[ 121.361305] usb 7-2: chopping to 0 config(s)
[ 121.373299] usb 7-2: string descriptor 0 read error: -32
[ 121.373314] usb 7-2: New USB device found, idVendor=045e, idProduct=0724
[ 121.373322] usb 7-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 121.373552] usb 7-2: no configuration chosen from 0 choices
[ 122.021805] usb 7-2: USB disconnect, device number 16
[ 123.893944] usb 8-2: new full-speed USB device number 3 using xhci_hcd
[ 123.948616] usb 8-2: New USB device found, idVendor=045e, idProduct=0724
[ 123.948628] usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 123.948636] usb 8-2: Product: SideWinder\xffffffe2\xffffff84\xffffffa2\xffffff84\xffffffa2 Mouse
[ 123.948642] usb 8-2: Manufacturer: Microsoft
[ 124.002539] input: Microsoft SideWinder\xffffffe2\xffffff84\xffffffa2\xffffff84\xffffffa2 Mouse as /devices/pci0000:00/0000:00:04.0/0000:02:00.0/usb8/8-2/8-2:1.0/input/input15
[ 124.002951] hid-generic 0003:045E:0724.0002: input,hidraw0: USB HID v1.11 Mouse [Microsoft SideWinder\xffffffe2\xffffff84\xffffffa2\xffffff84\xffffffa2 Mouse] on usb-0000:02:00.0-2/input0
[ 130.858512] usb 7-1: new low-speed USB device number 17 using ohci-pci
[ 130.998670] usb 7-1: device descriptor read/64, error -32
[ 131.242792] usb 7-1: device descriptor read/64, error -32
[ 131.482967] usb 7-1: new low-speed USB device number 18 using ohci-pci
[ 131.623082] usb 7-1: device descriptor read/64, error -32
[ 131.867159] usb 7-1: device descriptor read/64, error -32
[ 132.107404] usb 7-1: new low-speed USB device number 19 using ohci-pci
[ 132.355589] usb 7-1: New USB device found, idVendor=06a3, idProduct=0728
[ 132.355602] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 132.355610] usb 7-1: Product: Saitek Cyborg Keyboard
[ 132.355616] usb 7-1: Manufacturer: Chicony
[ 132.368250] input: Chicony Saitek Cyborg Keyboard as /devices/pci0000:00/0000:00:16.0/usb7/7-1/7-1:1.0/input/input16
[ 132.368510] hid-generic 0003:06A3:0728.0003: input,hidraw1: USB HID v1.11 Keyboard [Chicony Saitek Cyborg Keyboard] on usb-0000:00:16.0-1/input0
[ 132.369579] usb 7-1: ctrl urb status -62 received
[ 132.371555] usb 7-1: ctrl urb status -62 received
[ 132.378612] usbhid 7-1:1.1: can't add hid device: -62
[ 132.378652] usbhid: probe of 7-1:1.1 failed with error -62
[ 132.545660] usb 7-1: ctrl urb status -62 received
[ 133.130033] usb 7-1: ctrl urb status -62 received
[ 139.111173] usb 7-1: USB disconnect, device number 19
[ 145.705298] usb 8-2: USB disconnect, device number 3
[ 146.573047] usb 8-1: new full-speed USB device number 4 using xhci_hcd
[ 146.627457] usb 8-1: New USB device found, idVendor=045e, idProduct=0724
[ 146.627470] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 146.627477] usb 8-1: Product: SideWinder\xffffffe2\xffffff84\xffffffa2\xffffff84\xffffffa2 Mouse
[ 146.627483] usb 8-1: Manufacturer: Microsoft
[ 146.681376] input: Microsoft SideWinder\xffffffe2\xffffff84\xffffffa2\xffffff84\xffffffa2 Mouse as /devices/pci0000:00/0000:00:04.0/0000:02:00.0/usb8/8-1/8-1:1.0/input/input17
[ 146.681791] hid-generic 0003:045E:0724.0004: input,hidraw0: USB HID v1.11 Mouse [Microsoft SideWinder\xffffffe2\xffffff84\xffffffa2\xffffff84\xffffffa2 Mouse] on usb-0000:02:00.0-1/input0
[ 149.094668] usb 8-2: new low-speed USB device number 5 using xhci_hcd
[ 149.150168] usb 8-2: New USB device found, idVendor=06a3, idProduct=0728
[ 149.150180] usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 149.150188] usb 8-2: Product: Saitek Cyborg Keyboard
[ 149.150194] usb 8-2: Manufacturer: Chicony
[ 149.150441] usb 8-2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 149.150452] usb 8-2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 149.164777] input: Chicony Saitek Cyborg Keyboard as /devices/pci0000:00/0000:00:04.0/0000:02:00.0/usb8/8-2/8-2:1.0/input/input18
[ 149.165037] hid-generic 0003:06A3:0728.0005: input,hidraw1: USB HID v1.11 Keyboard [Chicony Saitek Cyborg Keyboard] on usb-0000:02:00.0-2/input0
[ 149.189301] input: Chicony Saitek Cyborg Keyboard as /devices/pci0000:00/0000:00:04.0/0000:02:00.0/usb8/8-2/8-2:1.1/input/input19
[ 149.189640] hid-generic 0003:06A3:0728.0006: input,hiddev0,hidraw2: USB HID v1.11 Device [Chicony Saitek Cyborg Keyboard] on usb-0000:02:00.0-2/input1
με την Ιομμυ ενεργοποιημένη λειτουργούν οι θύρες όποτε θυμηθούν , το πρόβλημα με τα αρχεία που καταστράφηκαν που είχα αναρτήσει εδώ απο αυτό προέκυψε ,
και έτσι απο τότε χρησιμοποιώ ubuntu 12.04 x32 ,