Έλεγχος σκληρού δίσκου Hardware

από **George Pantelis** » 26 Μάιος 2014, 12:36

Learner έγραψε:
George Pantelis έγραψε:Τα φώτα σας και την βοήθειά σας και για μένα παρακαλώ (μου βγάζει 4 errors). Τί συμβαίνει;

Εσύ φαίνεται να έχεις πιο σοβαρό πρόβλημα.
George Pantelis έγραψε:
Κώδικας: Επιλογή όλων
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 479 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 443

άρχισε η κάτω βόλτα. Κάποια στιγμή (και ίσως σύντομα, απ' ότι βλέπω από τις τιμές) θα εξαντληθούν οι τομείς που μπορούν να επανατοποθετηθούν και τότε...πάπαλα ο δίσκος.

Στην θέση σου, θα έψαχνα για δίσκο επί τόπου.

Eυχαριστώ Learner. Είχα μείνει ήσυχος επειδή το τεστ που του έκανα (στο help του ubuntu το βρήκα) μου τον έβγαλε οκ... Η γνώμη σου είναι να μην του δώσω βάση;
*Τί ακριβώς σημαίνει " Κάποια στιγμή (και ίσως σύντομα, απ' ότι βλέπω από τις τιμές) θα εξαντληθούν οι τομείς που μπορούν να επανατοποθετηθούν και τότε...πάπαλα ο δίσκος";

από **lepidas** » 26 Μάιος 2014, 12:49

Learner έγραψε:Δεν νομίζω ότι είναι για πέταμα οι δίσκοι. Έχουν κάποια λάθη, θέλουν προσοχή, αλλά μπορείς να τους δουλέψεις ακόμη. Μην νομίζεις ότι το 40 reallocated sectors είναι σημαντική τιμή για έναν δίσκο 3TB.
Απλά παρακολούθα/σύγκρινε τις τιμές ανά μήνα να δεις κατά πόσο αυξάνονται. Έχω δίσκο 1TB με χειρότερες τιμές από αυτές που βλέπω εδώ και τον δουλεύω ακόμη και με λειτουργικό σύστημα. Ναι, κάποια στιγμή θα τα παίξει το ξέρω (έχω πάρει τα backup μου), αλλά μέχρι τότε, δουλεύει μια χαρά.

αυτά που με ανησυχούν (μήπως γιατί δεν ξέρω τι λένε?) είναι τα παρακάτω απο τον /dev/sda

Κώδικας: Επιλογή όλων: ATA Error Count: 2060 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2060 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 6d+23:28:32.109 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 6d+23:28:32.108 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 6d+23:28:32.108 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 6d+23:28:32.108 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 6d+23:28:32.107 IDENTIFY DEVICE Error 2059 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 6d+23:28:29.233 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 6d+23:28:29.233 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 6d+23:28:29.232 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 6d+23:28:29.232 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 6d+23:28:29.232 IDENTIFY DEVICE Error 2058 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED 60 00 80 ff ff ff 4f 00 6d+23:28:26.348 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 6d+23:28:26.348 SET FEATURES [Enable SATA feature] Error 2057 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 6d+23:28:23.456 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 6d+23:28:23.456 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 6d+23:28:23.456 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 6d+23:28:23.456 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 6d+23:28:23.456 SET FEATURES [Set transfer mode] Error 2056 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 6d+23:28:20.581 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 6d+23:28:20.581 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 6d+23:28:20.581 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 6d+23:28:20.580 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 6d+23:28:20.580 SET FEATURES [Set transfer mode]

από **Learner** » 26 Μάιος 2014, 14:57

George Pantelis έγραψε:*Τί ακριβώς σημαίνει " Κάποια στιγμή (και ίσως σύντομα, απ' ότι βλέπω από τις τιμές) θα εξαντληθούν οι τομείς που μπορούν να επανατοποθετηθούν και τότε...πάπαλα ο δίσκος";

Διάβασε εδώ → viewtopic.php?f=9&t=21628&p=223843&http#%CE%94%CE%B5%CE%B4%CE%BF%CE%BC%CE%AD%CE%BD%CE%B1%20S.M.A.R.T (τον πίνακα).

lepidas έγραψε:αυτά που με ανησυχούν (μήπως γιατί δεν ξέρω τι λένε?) είναι τα παρακάτω απο τον /dev/sda

Μπα, εμένα δεν με ανησυχούν αυτά. Κάποια λάθη σε τυχαίες χρονικές στιγμές. Αυτά που πρέπει να σε ανησυχούν είναι οι τιμές του S.M.A.R.T.
Διάβασε κι εσύ τον παραπάνω πίνακα και κάνε τις συγκρίσεις σου.

από **lepidas** » 28 Μάιος 2014, 09:20

Για όποιον θέλει να ρίξει μια ματιά, οι τιμές αυξήθηκαν αισθητά μέσα σε 2 ημέρες.

26/5/2014

lepidas έγραψε:
Κώδικας: Επιλογή όλων
sudo smartctl -a /dev/sda smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST3000DM001-9YN166 Serial Number: Z1F15G6S LU WWN Device Id: 5 000c50 04e4699d2 Firmware Version: CC4B User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon May 26 08:32:54 2014 EEST ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/223651en SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 584) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 352) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 116 093 006 Pre-fail Always - 106101152 3 Spin_Up_Time 0x0003 093 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 15 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 8 7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 143463162 9 Power_On_Hours 0x0032 091 091 000 Old_age Always - 8439 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 15 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 2060 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 0 0 189 High_Fly_Writes 0x003a 098 098 000 Old_age Always - 2 190 Airflow_Temperature_Cel 0x0022 067 052 045 Old_age Always - 33 (Min/Max 32/35) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 9 193 Load_Cycle_Count 0x0032 077 077 000 Old_age Always - 46895 194 Temperature_Celsius 0x0022 033 048 000 Old_age Always - 33 (0 18 0 0 0) 197 Current_Pending_Sector 0x0012 100 001 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 001 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 6924h+51m+41.940s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 278506363319203 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 63036076050996 SMART Error Log Version: 1 ATA Error Count: 2060 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2060 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 6d+23:28:32.109 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 6d+23:28:32.108 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 6d+23:28:32.108 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 6d+23:28:32.108 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 6d+23:28:32.107 IDENTIFY DEVICE Error 2059 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 6d+23:28:29.233 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 6d+23:28:29.233 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 6d+23:28:29.232 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 6d+23:28:29.232 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 6d+23:28:29.232 IDENTIFY DEVICE Error 2058 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED 60 00 80 ff ff ff 4f 00 6d+23:28:26.348 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 6d+23:28:26.348 SET FEATURES [Enable SATA feature] Error 2057 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 6d+23:28:23.456 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 6d+23:28:23.456 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 6d+23:28:23.456 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 6d+23:28:23.456 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 6d+23:28:23.456 SET FEATURES [Set transfer mode] Error 2056 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 6d+23:28:20.581 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 6d+23:28:20.581 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 6d+23:28:20.581 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 6d+23:28:20.580 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 6d+23:28:20.580 SET FEATURES [Set transfer mode] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 6532 - # 2 Extended offline Completed without error 00% 6502 - # 3 Extended offline Completed without error 00% 5165 - # 4 Extended offline Completed without error 00% 5 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

Κώδικας: Επιλογή όλων
sudo smartctl -a /dev/sdb smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST3000DM001-1CH166 Serial Number: Z1F0Z1FL LU WWN Device Id: 5 000c50 04dffbbcb Firmware Version: CC43 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon May 26 08:37:44 2014 EEST ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/223651en SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 584) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 328) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 145310616 3 Spin_Up_Time 0x0003 091 091 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 21 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 40 7 Seek_Error_Rate 0x000f 053 051 030 Pre-fail Always - 1898462924882 9 Power_On_Hours 0x0032 087 087 000 Old_age Always - 11931 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 21 183 Runtime_Bad_Block 0x0032 099 099 000 Old_age Always - 1 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 097 097 000 Old_age Always - 3 188 Command_Timeout 0x0032 100 098 000 Old_age Always - 2 2 2 189 High_Fly_Writes 0x003a 028 028 000 Old_age Always - 72 190 Airflow_Temperature_Cel 0x0022 066 055 045 Old_age Always - 34 (Min/Max 33/37) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 19 193 Load_Cycle_Count 0x0032 083 083 000 Old_age Always - 35641 194 Temperature_Celsius 0x0022 034 045 000 Old_age Always - 34 (0 21 0 0 0) 197 Current_Pending_Sector 0x0012 100 032 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 032 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 11912h+29m+01.926s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 116064681029 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 326236248135 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 10025 - # 2 Extended offline Completed without error 00% 9996 - # 3 Extended offline Completed without error 00% 9629 - # 4 Extended offline Completed without error 00% 50 - # 5 Extended offline Completed without error 00% 6 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

28/5/2014

Κώδικας: Επιλογή όλων: sudo smartctl -a /dev/sda smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST3000DM001-9YN166 Serial Number: Z1F15G6S LU WWN Device Id: 5 000c50 04e4699d2 Firmware Version: CC4B User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Wed May 28 09:18:51 2014 EEST ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/223651en SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 584) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 352) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 117 093 006 Pre-fail Always - 117991696 3 Spin_Up_Time 0x0003 093 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 15 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 8 7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 144149703 9 Power_On_Hours 0x0032 091 091 000 Old_age Always - 8488 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 15 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 2060 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 0 0 189 High_Fly_Writes 0x003a 098 098 000 Old_age Always - 2 190 Airflow_Temperature_Cel 0x0022 067 052 045 Old_age Always - 33 (Min/Max 32/35) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 9 193 Load_Cycle_Count 0x0032 077 077 000 Old_age Always - 46895 194 Temperature_Celsius 0x0022 033 048 000 Old_age Always - 33 (0 18 0 0 0) 197 Current_Pending_Sector 0x0012 100 001 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 001 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 6973h+37m+58.250s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 278529293718899 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 63049642357404 SMART Error Log Version: 1 ATA Error Count: 2060 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2060 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 6d+23:28:32.109 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 6d+23:28:32.108 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 6d+23:28:32.108 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 6d+23:28:32.108 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 6d+23:28:32.107 IDENTIFY DEVICE Error 2059 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 6d+23:28:29.233 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 6d+23:28:29.233 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 6d+23:28:29.232 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 6d+23:28:29.232 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 6d+23:28:29.232 IDENTIFY DEVICE Error 2058 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 6d+23:28:26.349 READ FPDMA QUEUED 60 00 80 ff ff ff 4f 00 6d+23:28:26.348 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 6d+23:28:26.348 SET FEATURES [Enable SATA feature] Error 2057 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 6d+23:28:23.456 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 6d+23:28:23.456 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 6d+23:28:23.456 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 6d+23:28:23.456 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 6d+23:28:23.456 SET FEATURES [Set transfer mode] Error 2056 occurred at disk power-on lifetime: 5089 hours (212 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 6d+23:28:20.581 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 6d+23:28:20.581 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 6d+23:28:20.581 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 6d+23:28:20.580 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 6d+23:28:20.580 SET FEATURES [Set transfer mode] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 6532 - # 2 Extended offline Completed without error 00% 6502 - # 3 Extended offline Completed without error 00% 5165 - # 4 Extended offline Completed without error 00% 5 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

Κώδικας: Επιλογή όλων: sudo smartctl -a /dev/sdb smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST3000DM001-1CH166 Serial Number: Z1F0Z1FL LU WWN Device Id: 5 000c50 04dffbbcb Firmware Version: CC43 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Wed May 28 09:19:22 2014 EEST ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/223651en SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 584) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 328) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 147374912 3 Spin_Up_Time 0x0003 091 091 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 21 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 40 7 Seek_Error_Rate 0x000f 053 051 030 Pre-fail Always - 1898463545583 9 Power_On_Hours 0x0032 087 087 000 Old_age Always - 11980 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 21 183 Runtime_Bad_Block 0x0032 099 099 000 Old_age Always - 1 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 097 097 000 Old_age Always - 3 188 Command_Timeout 0x0032 100 098 000 Old_age Always - 2 2 2 189 High_Fly_Writes 0x003a 028 028 000 Old_age Always - 72 190 Airflow_Temperature_Cel 0x0022 066 055 045 Old_age Always - 34 (Min/Max 33/37) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 19 193 Load_Cycle_Count 0x0032 083 083 000 Old_age Always - 35641 194 Temperature_Celsius 0x0022 034 045 000 Old_age Always - 34 (0 21 0 0 0) 197 Current_Pending_Sector 0x0012 100 032 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 032 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 11961h+10m+57.745s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 116078149386 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 326236456001 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 10025 - # 2 Extended offline Completed without error 00% 9996 - # 3 Extended offline Completed without error 00% 9629 - # 4 Extended offline Completed without error 00% 50 - # 5 Extended offline Completed without error 00% 6 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

Οι δίσκοι είναι του σερβερ και μπορώ να πω να τους αντικαταστήσουν αρκεί να με βοηθήσετε, δηλαδή να τους πω "αυτό κι αυτό", δηλαδή πως να το δικαιολογήσω σε περίπτωση που κάνουν κάποια νάζια

από **the_eye** » 28 Μάιος 2014, 16:28

Δες τα id παρακάτω αν παρουσιάζουν τιμές.

Κώδικας: Επιλογή όλων: 1 Raw_Read_Error_Rate 5 Reallocated_Sector_Ct 7 Seek_Error_Rate 10 Spin_Retry_Count 188 Command_Timeout

Μετά δες το μοντέλο το δίσκου στην σελίδα του κατασκευαστή, τι λέει για τις τιμές αυτές. Οπότε θα έχεις όλα τα στοιχεία που χρειάζεσαι.

από **lepidas** » 28 Μάιος 2014, 19:25

Βρήκα αυτό στο wiki της Hetzner και μπορεί κάποιος μόνος του να καταλάβει πολλά πράγματα για το δίσκο. Προτείνω να μπεί στην πρώτη δημοσιεύση του θέματος ως link ή να μπεί paste το περιεχόμενο του συγκεκριμένου μόνο anchor link
http://wiki.hetzner.de/index.php/Serien ... Attributes

Ιστοσελίδα · από **dgtfeargr** » 29 Μάιος 2014, 11:19

the_eye έγραψε:Αν πιάνει το χέρι σου, θέλει πεπιεσμένο αέρα στους αεραγωγούς για να πετάξει τις σκόνες.
Μην δοκιμάσεις με σεσουάρ, δεν κάνει.

Τα σπρέι πεπιεσμένου αέρα πετάνε και υγρό μερικές φορές ειδικά αν τα ζορίζεις, υγρό το οποίο σε λίγα δευτερόλεπτα φεύγει. Μερικοί λένε ότι είναι για εξωτερική χρήση μόνο (πχ. πληκτρολόγιο) και άλλοι ότι κάνει και για τους αεραγωγούς αλλά και για το μέρος κάτω από το λάπτοπ αν αφαιρέσεις το πλαστικό καπάκι. Τι από τα 2 ισχύει; Μπορεί το σπρέι να κάνει ζημιά στο κάτω μέρος εσωτερικά;

από **matthew** » 29 Μάιος 2014, 12:19

Τα smd εξαρτήματα είναι γερά κολλημένα επάνω στις πλακέτες. Περισσότερη προσοχή χρειάζεται στα ψιλά καλώδια & στις μικρές & λεπτές καλωδιοταινίες όταν φυσάμε τα λάπτοπ. Ειδικά στις ενώσεις με τα φισάκια. Μπορεί να αποκολληθούν.

από **lepidas** » 29 Μάιος 2014, 14:55

το καλύτερο για απομάκρυνση της σκόνης είναι αυτό - 500Watt, θελει λιγη προσοχη γιατί μπορεί να "σηκώσει" και κουμπιά στο πληκτρολόγιο. κοστίζει περίπου 17 ευρώ και λειτουργεί με ρεύμα 220v, σε 2 λεπτα εχει καθαρισει εσωτερικά desktop, τα φορητα μεσα απο τις γριλιες κλπ.

από **sotos21** » 23 Ιούλ 2014, 11:46

Τι έχουμε να πούμε για τον παρακάτω δίσκο κύριοι

Κώδικας: Επιλογή όλων: sotiris@ubuntu:~$ sudo smartctl -a /dev/sda smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.16.0-5-generic] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Travelstar 5K320 Device Model: Hitachi HTS543225L9SA00 Serial Number: 080612FB2F00LLG2DKJA LU WWN Device Id: 5 000cca 55fc117e9 Firmware Version: FBEOC43C User Capacity: 250.059.350.016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 3f SATA Version is: SATA 2.6, 1.5 Gb/s Local Time is: Wed Jul 23 11:28:03 2014 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 645) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 102) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 095 095 062 Pre-fail Always - 1114112 2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0 3 Spin_Up_Time 0x0007 253 253 033 Pre-fail Always - 0 4 Start_Stop_Count 0x0012 098 098 000 Old_age Always - 3287 5 Reallocated_Sector_Ct 0x0033 073 073 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0 9 Power_On_Hours 0x0012 092 092 000 Old_age Always - 3760 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 2976 191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 098 098 000 Old_age Always - 491 193 Load_Cycle_Count 0x0012 094 094 000 Old_age Always - 62066 194 Temperature_Celsius 0x0002 141 141 000 Old_age Always - 39 (Min/Max 8/48) 196 Reallocated_Event_Count 0x0032 068 068 000 Old_age Always - 1836 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 51 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 1399 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1399 occurred at disk power-on lifetime: 3722 hours (155 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 5e 94 2a 73 e1 Error: UNC 94 sectors at LBA = 0x01732a94 = 24324756 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 7f 73 2a 73 e0 00 00:00:16.900 READ DMA EXT 25 00 7f f4 29 73 e0 00 00:00:12.900 READ DMA EXT 25 00 7f 75 29 73 e0 00 00:00:12.900 READ DMA EXT 25 00 7f f6 28 73 e0 00 00:00:12.900 READ DMA EXT 25 00 7f 77 28 73 e0 00 00:00:12.900 READ DMA EXT Error 1398 occurred at disk power-on lifetime: 3722 hours (155 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 5e 94 2a 73 e1 Error: UNC 94 sectors at LBA = 0x01732a94 = 24324756 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 7f 73 2a 73 e0 00 00:00:15.600 READ DMA EXT 25 00 7f f4 29 73 e0 00 00:00:12.700 READ DMA EXT 25 00 7f 75 29 73 e0 00 00:00:12.700 READ DMA EXT 25 00 7f f6 28 73 e0 00 00:00:12.700 READ DMA EXT 25 00 7f 77 28 73 e0 00 00:00:12.700 READ DMA EXT Error 1397 occurred at disk power-on lifetime: 3722 hours (155 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 61 91 2a 73 e1 Error: UNC 97 sectors at LBA = 0x01732a91 = 24324753 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 7f 73 2a 73 e0 00 00:00:16.800 READ DMA EXT 25 00 7f f4 29 73 e0 00 00:00:14.700 READ DMA EXT 25 00 7f 75 29 73 e0 00 00:00:14.700 READ DMA EXT 25 00 7f f6 28 73 e0 00 00:00:14.700 READ DMA EXT 25 00 7f 77 28 73 e0 00 00:00:14.700 READ DMA EXT Error 1396 occurred at disk power-on lifetime: 3682 hours (153 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 51 3d 79 0c e9 Error: UNC 81 sectors at LBA = 0x090c793d = 151812413 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 7f 0f 79 0c e0 00 00:01:34.100 READ DMA EXT 25 00 7f 90 78 0c e0 00 00:01:31.400 READ DMA EXT 25 00 02 58 bb 63 e0 00 00:01:31.400 READ DMA EXT 25 00 08 78 80 04 e0 00 00:01:31.400 READ DMA EXT 25 00 02 16 77 64 e0 00 00:01:31.400 READ DMA EXT Error 1395 occurred at disk power-on lifetime: 3682 hours (153 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 69 25 79 0c e9 Error: UNC 105 sectors at LBA = 0x090c7925 = 151812389 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 7f 0f 79 0c e0 00 00:00:10.800 READ DMA EXT 25 00 7f 90 78 0c e0 00 00:00:07.700 READ DMA EXT 25 00 02 58 bb 63 e0 00 00:00:07.600 READ DMA EXT 25 00 08 78 80 04 e0 00 00:00:07.600 READ DMA EXT 25 00 02 16 77 64 e0 00 00:00:07.600 READ DMA EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 3754 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

Έκανα το τεστ γιατί η εφαρμογή "Δίσκοι" έλεγε χτες 37 ελαττωματικοί τομείς, το πρωί 47, και τώρα 51.

Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware