Σελίδα 3 από 44
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
06 Σεπ 2011, 01:39
από the_eye
Καλό είναι να τον αντικαταστήσεις.
Από την σκόνη δεν παθαίνει ζημιά ο δίσκος γιατί είναι ερμητικά κλειστός.
Η σκόνη όμως είναι η αιτία του σφάλματος που είχες στην εικόνα παραπάνω. Γενικά υπολογιστές και σκόνη είναι κακός συνδυασμός. Κάντου έναν καθαρισμό με πεπιεσμένο αέρα (όχι με κανένα κομπρεσερ από το εργοτάξιο, γιατί θα πάρεις τα εξαρτήματα στο χέρι)
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
06 Σεπ 2011, 09:55
από Th P
Καλημέρα στην κοινότητα
Ενώ παίρνω αυτό:
- Κώδικας: Επιλογή όλων
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MK..52GSX series
Device Model: TOSHIBA MK3252GSX
Serial Number: 98FNT1AIT
Firmware Version: LV010A
User Capacity: 320.072.933.376 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Sep 6 09:45:40 2011 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 135) minutes.
SCT capabilities: (0x0039) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1600
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 4211
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 20
7 Seek_Error_Rate 0x000b 100 099 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 084 084 000 Old_age Always - 6779
10 Spin_Retry_Count 0x0033 184 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 4097
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 877
193 Load_Cycle_Count 0x0032 095 095 000 Old_age Always - 54961
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 42 (Lifetime Min/Max 12/48)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 20
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 8310
222 Loaded_Hours 0x0032 086 086 000 Old_age Always - 5989
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 223
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 5774 -
# 2 Short offline Completed without error 00% 5583 -
# 3 Short offline Completed without error 00% 5566 -
# 4 Short offline Completed without error 00% 5565 -
# 5 Short offline Completed without error 00% 5560 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Έχω παράλληλα και αυτό:
Edit: που μάλλον αφορά αυτό:
- Κώδικας: Επιλογή όλων
Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 20
χωρίς να έχω παράξενα κολλήματα κλπ.
Είναι σοβαρό αυτό το σφάλμα;
Διορθώνεται;
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
06 Σεπ 2011, 11:34
από the_eye
Δεν έχεις πρόβλημα, επειδή οι άλλοι δείκτες είναι μηδέν.
Πρέπει να ελέγχεις που και που για να δεις αν το νούμερο θα ανεβεί. Αν αρχίσει να ανεβαίνει τότε θα υπάρχει πρόβλημα.
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
06 Σεπ 2011, 12:06
από Th P
@the_eye
Ok!
Ευχαριστώ!
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
06 Σεπ 2011, 16:17
από pc_magas
Το raw read error rate δεν μου αρέσει αλλά μήπως έχει τιμή επειδή το εκτέλεσα σε φορητό Η/Υ? (το νετμπουκ στην υπογραφή μου)
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
06 Σεπ 2011, 16:52
από the_eye
Το raw read error rate είναι ανάλογα με τον κατασκευαστή, δεν πρέπει να είναι απαραίτητα μηδέν. Πρέπει να το δεις μαζί με άλλους δείκτες.
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
06 Νοέμ 2011, 21:37
από telis_petsotis
για ριξε κ εδω μια ματια
- Κώδικας: Επιλογή όλων
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD1200BEVT-22ZCT0
Serial Number: WD-WXC708C55676
Firmware Version: 11.01A11
User Capacity: 120.034.123.776 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Nov 6 20:35:49 2011 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (4560) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 57) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 159 156 021 Pre-fail Always - 1033
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2740
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 4151
10 Spin_Retry_Count 0x0033 100 095 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1942
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 122
193 Load_Cycle_Count 0x0032 180 180 000 Old_age Always - 61253
194 Temperature_Celsius 0x0022 096 084 000 Old_age Always - 47
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 24 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 24 occurred at disk power-on lifetime: 2134 hours (88 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3c 6c aa 64 e0 Error: UNC 60 sectors at LBA = 0x0064aa6c = 6597228
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 20 3c 6c aa 64 06 00 00:00:59.236 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:56.261 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:53.146 READ DMA EXT
25 20 04 68 aa 64 06 00 00:00:53.146 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:50.033 READ DMA EXT
Error 23 occurred at disk power-on lifetime: 2134 hours (88 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3c 6c aa 64 e0 Error: UNC 60 sectors at LBA = 0x0064aa6c = 6597228
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 20 3c 6c aa 64 06 00 00:00:56.261 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:53.146 READ DMA EXT
25 20 04 68 aa 64 06 00 00:00:53.146 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:50.033 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:46.923 READ DMA EXT
Error 22 occurred at disk power-on lifetime: 2134 hours (88 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3c 6c aa 64 e0 Error: UNC 60 sectors at LBA = 0x0064aa6c = 6597228
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 20 3c 6c aa 64 06 00 00:00:53.146 READ DMA EXT
25 20 04 68 aa 64 06 00 00:00:53.146 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:50.033 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:46.923 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:43.666 READ DMA EXT
Error 21 occurred at disk power-on lifetime: 2134 hours (88 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3c 6c aa 64 e0 Error: UNC 60 sectors at LBA = 0x0064aa6c = 6597228
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 20 3c 6c aa 64 06 00 00:00:50.033 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:46.923 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:43.666 READ DMA EXT
25 20 04 68 aa 64 06 00 00:00:43.665 READ DMA EXT
25 20 3b 2d aa 64 06 00 00:00:43.665 READ DMA EXT
Error 20 occurred at disk power-on lifetime: 2134 hours (88 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 3c 6c aa 64 e0 Error: UNC 60 sectors at LBA = 0x0064aa6c = 6597228
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 20 3c 6c aa 64 06 00 00:00:46.923 READ DMA EXT
25 20 3c 6c aa 64 06 00 00:00:43.666 READ DMA EXT
25 20 04 68 aa 64 06 00 00:00:43.665 READ DMA EXT
25 20 3b 2d aa 64 06 00 00:00:43.665 READ DMA EXT
25 20 05 28 aa 64 06 00 00:00:43.665 READ DMA EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
07 Νοέμ 2011, 02:22
από Learner
Th P έγραψε:Έχω παράλληλα και αυτό:
Edit: που μάλλον αφορά αυτό:
- Κώδικας: Επιλογή όλων
Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 20
χωρίς να έχω παράξενα κολλήματα κλπ.
Είναι σοβαρό αυτό το σφάλμα;
Διορθώνεται;
Έχω κι εγώ reallocated sectors , στον 250αρι της υπογραφής μου. Δεν μου δημιουργούν κάποιο πρόβλημα όμως. Δοκίμασα να τους διορθώσω με κάποιο πρόγραμμα (spinrite νομίζω λεγόταν) και από 6 γίνανε 12. Αυτό στο λέω για να μην εκτελέσεις τίποτα προγράμματα που και καλά διορθώνουν το πρόβλημα . Ας το όπως είναι αρκεί να μην αυξάνονται με τον καιρό . Εμένα είναι σταθεροί τώρα 1-2 μήνες περίπου.
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
17 Νοέμ 2011, 16:55
από airmaik
εκανα εναν ελεγχο στον σκληρο μου και ειδα αυτην την εικονα
http://img812.imageshack.us/img812/9615/screenshotat20111117134.pngμετα δινω και αυτο
- Κώδικας: Επιλογή όλων
sudo smartctl -a /dev/sda
και μου βγαζει αυτα
- Κώδικας: Επιλογή όλων
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.0.0-12-generic] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.12
Device Model: ST3500418AS
Serial Number: 6VM1NHT1
LU WWN Device Id: 5 000c50 014019626
Firmware Version: CC34
User Capacity: 500,106,780,160 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Thu Nov 17 13:54:05 2011 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 90) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 116 099 006 Pre-fail Always - 103419890
3 Spin_Up_Time 0x0003 098 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1358
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 22
7 Seek_Error_Rate 0x000f 082 060 030 Pre-fail Always - 180469905
9 Power_On_Hours 0x0032 092 092 000 Old_age Always - 7875
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1359
183 Runtime_Bad_Block 0x0000 100 100 000 Old_age Offline - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 19
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 070 056 045 Old_age Always - 30 (Min/Max 29/30)
194 Temperature_Celsius 0x0022 030 044 000 Old_age Always - 30 (0 8 0 0)
195 Hardware_ECC_Recovered 0x001a 041 022 000 Old_age Always - 103419890
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 79688823221579
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 847550096
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 2758260502
SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2 occurred at disk power-on lifetime: 5913 hours (246 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ef 81 5e 00 Error: UNC at LBA = 0x005e81ef = 6193647
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 e8 81 5e e0 00 00:00:32.192 READ DMA EXT
25 00 08 e8 81 5e e0 00 00:00:29.520 READ DMA EXT
25 00 80 08 8e 7f e0 00 00:00:29.519 READ DMA EXT
25 00 80 88 8d 7f e0 00 00:00:29.509 READ DMA EXT
25 00 20 f0 07 5e e0 00 00:00:29.493 READ DMA EXT
Error 1 occurred at disk power-on lifetime: 5913 hours (246 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ef 81 5e 00 Error: UNC at LBA = 0x005e81ef = 6193647
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 e8 81 5e e0 00 00:00:29.520 READ DMA EXT
25 00 80 08 8e 7f e0 00 00:00:29.519 READ DMA EXT
25 00 80 88 8d 7f e0 00 00:00:29.509 READ DMA EXT
25 00 20 f0 07 5e e0 00 00:00:29.493 READ DMA EXT
25 00 08 ff ff ff ef 00 00:00:29.476 READ DMA EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
πρεπει να ανυσυχω?
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
17 Νοέμ 2011, 17:14
από the_eye
airmaik έγραψε:πρεπει να ανυσυχω?
Ναι ! Ο δίσκος σου έχει πρόβλημα.