Καλημέρα στο forum. Το laptop της υπογραφής έχει δυο σκληρούς, ένα ssd με 18.10 και 16.04 για λειτουργικά και ένα hdd(στη θέση του dvd) διαμορφωμένο σε ext4 και μόνιμα προσαρτημένο για αποθήκη.
Όλα ξεκίνησαν όταν έφερα από την δουλειά ένα ποντίκι που θέλανε να πετάξουν σαν προβληματικό. Το σύνδεσα σε μια θύρα και πάτησα το power, πήρε ρεύμα το ποντίκι(αφού άναψε το φωτάκι του) αλλά ο υπολογιστής έμεινε κολλημένος για 2 λεπτά πριν τον grub, στην φάση δηλαδή που ελέγχει το hardware. Τον έκλεισα από το κουμπί αφαίρεσα το ποντίκι αλλά το laptop έκανε 3 λεπτά να φτάσει στον grub και μετά δεν ξεκινούσε δείχνοντας από τα μηνύματα πρόβλημα στον δεύτερο σκληρό.
Εδώ πρέπει να γκρινιάξω λίγο, (καιρό έχω άλλωστε να το κάνω) την παλιά εποχή έβγαινε μήνυμα λέγοντας ότι δεν μπορεί να προσαρτήσει κάτι και παρότρυνε να πατήσουμε S για αγνόηση. Τώρα πάνε αυτά, έπρεπε να αλλάξω την εγγραφή στο /etc/fstab βάζοντας # μπροστά από το UUID του προβληματικού δίσκου.
Όταν αφαιρώ τον δίσκο όλα καλά, όταν είναι συνδεδεμένος κάνει όπως είπα 3 λεπτά για να φτάσει στον grub και μετά όλα είναι νορμάλ αλλά δεν μπορώ να τον προσαρτήσω. Ότι ενέργειες έχω κάνει θα τις αναρτήσω σε νέο νήμα αλλά πρώτα να δούμε αν είναι εντάξει ο δίσκος γιατί χρειάζομαι τα δεδομένα του.
- Κώδικας: Επιλογή όλων
sotiris@ubuntu:~$ sudo smartctl -a /dev/sdb
[sudo] password for sotiris:
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.18.0-10-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD100
Serial Number: Z3J5C03ST
LU WWN Device Id: 5 000039 533507fb4
Firmware Version: AX104H
User Capacity: 1.000.204.886.016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Nov 3 07:12:46 2018 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 237) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1814
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 6555
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 055 055 000 Old_age Always - 18154
10 Spin_Retry_Count 0x0033 229 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 5341
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 278
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 8388825
193 Load_Cycle_Count 0x0032 031 031 000 Old_age Always - 690392
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 24 (Min/Max 11/48)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 8
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 253 000 Old_age Always - 1
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 075 075 000 Old_age Always - 10251
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 272
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 128
SMART Error Log Version: 1
ATA Error Count: 3125 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 3125 occurred at disk power-on lifetime: 18154 hours (756 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 80 00 08 00 40 Error: UNC at LBA = 0x00000800 = 2048
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 80 00 08 00 40 00 00:04:00.899 READ FPDMA QUEUED
ef 05 fe 00 00 00 40 00 00:04:00.899 SET FEATURES [Enable APM]
e5 00 00 00 00 00 00 00 00:04:00.899 CHECK POWER MODE
ef 10 02 00 00 00 a0 00 00:04:00.898 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:04:00.898 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 3124 occurred at disk power-on lifetime: 18154 hours (756 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 00 00 08 00 40 Error: UNC at LBA = 0x00000800 = 2048
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 00 00 08 00 40 00 00:03:57.100 READ FPDMA QUEUED
b0 da 00 00 4f c2 00 00 00:03:57.000 SMART RETURN STATUS
ec 00 01 00 00 00 40 00 00:03:56.999 IDENTIFY DEVICE
b0 d5 01 01 4f c2 00 00 00:03:56.926 SMART READ LOG
60 08 b8 f0 67 70 40 00 00:03:56.902 READ FPDMA QUEUED
Error 3123 occurred at disk power-on lifetime: 18154 hours (756 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 d0 00 08 00 40 Error: UNC at LBA = 0x00000800 = 2048
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 d0 00 08 00 40 00 00:03:52.608 READ FPDMA QUEUED
ec 00 01 00 00 00 00 00 00:03:52.608 IDENTIFY DEVICE
ec 00 01 00 00 00 00 00 00:03:52.607 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 00 00:03:52.607 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:03:52.606 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 3122 occurred at disk power-on lifetime: 18154 hours (756 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 58 00 08 00 40 Error: UNC at LBA = 0x00000800 = 2048
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 58 00 08 00 40 00 00:03:48.798 READ FPDMA QUEUED
60 08 50 a0 61 70 40 00 00:03:48.794 READ FPDMA QUEUED
60 08 48 f8 69 70 40 00 00:03:48.785 READ FPDMA QUEUED
60 08 40 d0 69 70 40 00 00:03:48.785 READ FPDMA QUEUED
60 08 38 e0 69 70 40 00 00:03:48.785 READ FPDMA QUEUED
Error 3121 occurred at disk power-on lifetime: 18154 hours (756 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 a0 00 08 00 40 Error: UNC at LBA = 0x00000800 = 2048
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 a0 00 08 00 40 00 00:03:44.027 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:03:44.027 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:03:44.026 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:03:44.026 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 00:03:44.025 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
sotiris@ubuntu:~$
Εγώ δεν βλέπω κάτι και τείνω προς πρόβλημα στο σύστημα αρχείων. Αν βλέπετε κάτι πείτε το.