Ubuntu-gr Forum

Έτρεξα memtest και μου έδωσε αυτά τα αποτελέσματα
http://imagebin.ubuntu-gr.org/files2017/1566285509.png

Μετά πρέπει να κάνεις harware ελέγχους πχ να μετρήσεις το τροφοδοτικό, να κάνεις ένα οπτικό έλεγχο στην μητρική και χαλασμένους πυκνωτές, κτλ κτλ

Ευχαριστώ. Αυτό θέλει αρκετό χρόνο και πρέπει να αγοράσω πολύμετρo. Μετά τις διακοπές.

Κώδικας: Επιλογή όλων: invisible@invisible-Aspire-7736:~$ sudo smartctl -a /dev/sda smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-166-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Patriot Burst Serial Number: A472078C043000471109 Firmware Version: SBFM61.3 User Capacity: 480.103.981.056 bytes [480 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: Unknown(0x0ff8) (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Oct 26 22:40:39 2019 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 2870 12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 608 168 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 0 170 Unknown_Attribute 0x0003 065 065 010 Pre-fail Always - 222 173 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 655391 192 Power-Off_Retract_Count 0x0012 100 100 000 Old_age Always - 21 194 Temperature_Celsius 0x0023 067 067 000 Pre-fail Always - 33 (Min/Max 33/33) 218 Unknown_Attribute 0x000b 100 100 050 Pre-fail Always - 0 231 Temperature_Celsius 0x0013 100 100 000 Pre-fail Always - 99 241 Total_LBAs_Written 0x0012 100 100 000 Old_age Always - 3586 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. invisible@invisible-Aspire-7736:~$ sudo smartctl -a /dev/sdb smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-166-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD5000BEVT-22ZAT0 Serial Number: WD-WXQ0A99J4715 LU WWN Device Id: 5 0014ee 2039148a1 Firmware Version: 01.01A01 User Capacity: 500.107.862.016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Oct 26 22:41:39 2019 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13200) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 154) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 5449 3 Spin_Up_Time 0x0027 186 174 021 Pre-fail Always - 1700 4 Start_Stop_Count 0x0032 088 088 000 Old_age Always - 12297 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 065 065 000 Old_age Always - 26119 10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 091 091 000 Old_age Always - 9661 192 Power-Off_Retract_Count 0x0032 199 199 000 Old_age Always - 1191 193 Load_Cycle_Count 0x0032 117 117 000 Old_age Always - 250703 194 Temperature_Celsius 0x0022 113 080 000 Old_age Always - 34 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0 SMART Error Log Version: 1 Warning: ATA error count 12310 inconsistent with error log pointer 1 ATA Error Count: 12310 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 12310 occurred at disk power-on lifetime: 22609 hours (942 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 10 00 00 00 40 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c6 00 10 00 00 00 00 00 00:43:11.734 SET MULTIPLE MODE ec 00 00 00 00 00 00 00 00:43:11.733 IDENTIFY DEVICE ef 02 00 00 00 00 00 00 00:43:08.587 SET FEATURES [Enable write cache] ef 03 46 00 00 00 00 00 00:43:08.509 SET FEATURES [Set transfer mode] Error 12309 occurred at disk power-on lifetime: 22609 hours (942 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 00 00 00 00 40 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 02 00 00 00 00 00 00 00:43:08.587 SET FEATURES [Enable write cache] ef 03 46 00 00 00 00 00 00:43:08.509 SET FEATURES [Set transfer mode] c6 00 10 00 00 00 00 00 00:43:08.375 SET MULTIPLE MODE Error 12308 occurred at disk power-on lifetime: 22609 hours (942 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 46 00 00 00 40 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 03 46 00 00 00 00 00 00:43:08.509 SET FEATURES [Set transfer mode] c6 00 10 00 00 00 00 00 00:43:08.375 SET MULTIPLE MODE ef 02 00 00 00 00 00 00 00:43:07.889 SET FEATURES [Enable write cache] Error 12307 occurred at disk power-on lifetime: 22609 hours (942 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 10 00 00 00 40 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c6 00 10 00 00 00 00 00 00:43:08.375 SET MULTIPLE MODE ef 02 00 00 00 00 00 00 00:43:07.889 SET FEATURES [Enable write cache] ef 03 46 00 00 00 00 00 00:43:07.811 SET FEATURES [Set transfer mode] SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. invisible@invisible-Aspire-7736:~$

Ναι, έχει πρόβλημα

Κώδικας: Επιλογή όλων: 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 5449

Κώδικας: Επιλογή όλων: SMART Error Log Version: 1 Warning: ATA error count 12310 inconsistent with error log pointer 1

the_eye έγραψε:Ναι, έχει πρόβλημα
Κώδικας: Επιλογή όλων
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 5449

Κώδικας: Επιλογή όλων
SMART Error Log Version: 1 Warning: ATA error count 12310 inconsistent with error log pointer 1

10 ετών σκληρός φορητού υπολογιστή, τα έφαγε τα ψωμάκια του

Κώδικας: Επιλογή όλων: A B ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 119 099 006 Pre-fail Always - 225047536 154471120 3 Spin_Up_Time 0x0003 098 097 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 2021 1547 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 262701864 41911237 9 Power_On_Hours 0x0032 080 080 000 Old_age Always - 18094 10789 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always - 2055 1806 183 Runtime_Bad_Block 0x0000 100 100 000 Old_age Offline - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 099 000 Old_age Always - 662 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 073 054 045 Old_age Always - 27 (Min/Max 17/27) 194 Temperature_Celsius 0x0022 027 046 000 Old_age Always - 27 (0 13 0 0 0) 195 Hardware_ECC_Recovered 0x001a 062 044 000 Old_age Always - 225047536 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 23550 (172 199 0) 11519h+42m+46.834s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2757098482 8282180047 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 692458144 66937135246

Ποιος είναι καλύτερός ;

Έχουν πρόβλημα και οι 2.
Δεν νομίζω ότι υπάρχει καλύτερος ανάμεσα σε 2 χαλασμένους δίσκους.

Κώδικας: Επιλογή όλων: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 10 12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 13 168 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 0 170 Unknown_Attribute 0x0003 100 100 010 Pre-fail Always - 82 173 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 1 192 Power-Off_Retract_Count 0x0012 100 100 000 Old_age Always - 7 194 Temperature_Celsius 0x0023 067 067 000 Pre-fail Always - 33 (Min/Max 33/33) 218 Unknown_Attribute 0x000b 100 100 050 Pre-fail Always - 0 231 Temperature_Celsius 0x0013 100 100 000 Pre-fail Always - 100 241 Total_LBAs_Written 0x0012 100 100 000 Old_age Always - 44

Φαίνεται καλός.

Αγόρασες καινούριο ; 10 ώρες λειτουργία !

Κώδικας: Επιλογή όλων: 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 10

Τι δίσκος είναι ; Μου κάνει εντύπωση γιατί έχει πολλά Unknown_Attribute, για δώσε όλο το αποτέλεσμα της εντολής.

Ubuntu-gr Forum

Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware

Re: Έλεγχος σκληρού δίσκου Hardware