Σελίδα 7 από 44
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
29 Μάιος 2012, 18:03
από g1wrg0s
στο εργαλειο δισκων του ubuntu εχει τα ιδια αποτελεσματα για τον σκληρο. Η μονη διαφορα οτι εκει τον βγαζει "Υγιες" και καλα . Μπορεις να γινεις λιγο πιο ξεκαθαρος οταν λες "Εχει προβλημα" ; . Με λιγα λογια θελω να ξερω αν η αναγκη αποκαταστασης του ειναι αμεση ή εχω καποιο χρονο μεχρι να δω τι θα κανω .
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
29 Μάιος 2012, 22:02
από the_eye
Το εργαλείο δίσκων κοιτάζει μόνο για bad sectors. Οπότε αρκετές φορές δεν αντικατοπτρίζει την εικόνα του δίσκου.
Δες τις γραμμές που σου παρέθεσα στο προηγούμενο μήνυμα με τα errors. Οι κανονικές τιμές θα έπρεπε να ήταν μηδέν.
Δεν νομίζω ότι κανένας μπορεί να εκτιμήσει πότε θα χαλάσει μια ηλεκτρομηχανική συσκευή, απλά εντοπίζουμε ότι έχει πρόβλημα στην λειτουργία της.
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
02 Ιουν 2012, 13:17
από kouskous
τον δικο μου πως το βλεπετε παιδια???
- Κώδικας: Επιλογή όλων
eric@kouskous:~$ sudo smartctl -a /dev/sda
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-25-generic] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA
Device Model: WDC WD3200BEVT-75A23T0
Serial Number: WD-WXD1A20L6736
LU WWN Device Id: 5 0014ee 25985c789
Firmware Version: 01.01A01
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sat Jun 2 13:09:26 2012 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 7800) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 93) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7037) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 1641
3 Spin_Up_Time 0x0027 155 150 021 Pre-fail Always - 1225
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2041
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 4723
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1582
191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 10246
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 512
193 Load_Cycle_Count 0x0032 180 180 000 Old_age Always - 62995
194 Temperature_Celsius 0x0022 113 091 000 Old_age Always - 30
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
240 Head_Flying_Hours 0x0032 094 094 000 Old_age Always - 4687
241 Total_LBAs_Written 0x0032 200 200 000 Old_age Always - 10977896548
242 Total_LBAs_Read 0x0032 200 200 000 Old_age Always - 8821256601
254 Free_Fall_Sensor 0x0032 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Conveyance offline Completed: read failure 90% 4703 128159107
# 2 Extended offline Completed: read failure 90% 4703 128226564
# 3 Conveyance offline Completed: read failure 90% 4703 128226564
# 4 Short offline Completed: read failure 90% 4703 128226564
# 5 Offline Interrupted (host reset) 00% 4220 -
# 6 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
03 Ιουν 2012, 04:28
από Learner
Περίμενε να σου πει και κάποιος που ξέρει καλύτερα , αυτό που καταλαβαίνω εγώ είναι πως σε γενικές γραμμές καλά είναι ο δίσκος σου , αλλά μήπως....
..."έχεις κάνει το laptop φραπέ" ;
kouskous έγραψε:- Κώδικας: Επιλογή όλων
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 1641
191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 10246
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
03 Ιουν 2012, 20:35
από kouskous
τι θες να πεις???? ο δισκος ειναι φορμαρισμενος και εχει 4 κομματια...
3 για το ubuntu και 1 για τα win7....
αν εχω κανει καποιο λαθος που μπορει να κανει το δισκο να συμπεριφερετε καλυτερα...απλα ακουω!!!
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
03 Ιουν 2012, 20:39
από the_eye
Ο αισθητήρας κραδασμών του δίσκου έχει εντοπίσει πολλούς κραδασμούς, θα ήταν καλό να μην το μετακινείς εν' ώρα λειτουργίας.
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
03 Ιουν 2012, 20:42
από kouskous
δεν τον μετακινω ειναι πανω σε μια βαση μονημα το λαπτοπ....λες να εχω προβλημα απο αυτο?
το 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 1641 εγινε 1644 κακο αυτο?
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
03 Ιουν 2012, 20:56
από Learner
kouskous έγραψε:δεν τον μετακινω ειναι πανω σε μια βαση μονημα το λαπτοπ....λες να εχω προβλημα απο αυτο?
το 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 1641 εγινε 1644 κακο αυτο?
Οι κραδασμοί αυξήθηκαν ;
- Κώδικας: Επιλογή όλων
191 G-Sense_Error_Rate
η τιμή του Read_Error_Rate δεν είναι στάνταρ για όλους τους δίσκους. Διάβασε εδώ -->
Δεδομένα S.M.A.R.T σχετικά με αυτή την τιμή.
Καλό βέβαια δεν είναι που αυξάνει , αλλά δεν ξέρω κατά πόσο πρέπει να ανησυχείς αφού οι υπόλοιπες τιμές φαίνονται καλές .
Re: Έλεγχος σκληρού δίσκου Hardware
Δημοσιεύτηκε:
03 Ιουν 2012, 21:01
από kouskous
οχι φιλε μου αυτοι εως τωρα ειναι σταθεροι αλλα αν συνδιασω τα γεγονοτα πριν κανενα μηνα ξαφνικα δεν ανοιγε το pc οποτε δεν ηξερα τι φτεει και αναγκαστηκα να ξανακανω εγκατασταση απο την αρχη...
ισως την εχει ακουσει ο σκληρος και ειμαι σιγα σιγα για αλλαγη
Σφαλμα Δισκου - S.M.A.R.T. Failure
Δημοσιεύτηκε:
09 Ιουν 2012, 23:08
από Πετραν
ενας η/υ στην εκκινηση του μου δηλωνει S.M.A.R.T. Failure
του εκανα ενα τσεκ με smartmontools
και μου επεστρεψε αυτο το log
- Κώδικας: Επιλογή όλων
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-23-generic] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA
Device Model: WDC WD1600BEVS-07RST0
Serial Number: WD-WXE807637478
LU WWN Device Id: 5 0014ee 2ab1b1e8c
Firmware Version: 04.01G04
User Capacity: 160.041.885.696 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sat Jun 9 22:42:13 2012 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 6780) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 87) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 115
3 Spin_Up_Time 0x0003 189 186 021 Pre-fail Always - 1508
4 Start_Stop_Count 0x0032 097 097 000 Old_age Always - 3072
5 Reallocated_Sector_Ct 0x0033 133 133 140 Pre-fail Always FAILING_NOW 536
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1507
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1636
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 476
193 Load_Cycle_Count 0x0032 189 189 000 Old_age Always - 34031
194 Temperature_Celsius 0x0022 100 091 000 Old_age Always - 47
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 4
198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 80 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 80 occurred at disk power-on lifetime: 1480 hours (61 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 48 0c c1 e0 Error: UNC 8 sectors at LBA = 0x00c10c48 = 12651592
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 48 0c c1 11 08 00:12:38.200 READ DMA EXT
ef 10 02 00 00 00 00 08 00:12:38.199 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 08 00:12:38.199 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 00:12:38.199 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 00:12:38.199 SET FEATURES [Set transfer mode]
Error 79 occurred at disk power-on lifetime: 1480 hours (61 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 48 0c c1 e0 Error: UNC 8 sectors at LBA = 0x00c10c48 = 12651592
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 48 0c c1 11 08 00:12:35.179 READ DMA EXT
ef 10 02 00 00 00 00 08 00:12:35.179 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 08 00:12:35.179 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 00:12:35.179 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 00:12:35.179 SET FEATURES [Set transfer mode]
Error 78 occurred at disk power-on lifetime: 1480 hours (61 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 48 0c c1 e0 Error: UNC 8 sectors at LBA = 0x00c10c48 = 12651592
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 48 0c c1 11 08 00:12:32.338 READ DMA EXT
ef 10 02 00 00 00 00 08 00:12:32.337 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 08 00:12:32.337 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 00:12:32.337 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 00:12:32.337 SET FEATURES [Set transfer mode]
Error 77 occurred at disk power-on lifetime: 1480 hours (61 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 48 0c c1 e0 Error: UNC 8 sectors at LBA = 0x00c10c48 = 12651592
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 48 0c c1 11 08 00:12:29.153 READ DMA EXT
ef 10 02 00 00 00 00 08 00:12:29.153 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 08 00:12:29.153 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 00:12:29.153 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 00:12:29.153 SET FEATURES [Set transfer mode]
Error 76 occurred at disk power-on lifetime: 1480 hours (61 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 08 48 0c c1 e0 Error: AMNF 8 sectors at LBA = 0x00c10c48 = 12651592
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 48 0c c1 11 08 00:12:26.308 READ DMA EXT
ef 10 02 00 00 00 00 08 00:12:26.308 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 08 00:12:26.307 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 00:12:26.307 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 00:12:26.307 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
και καθως δεν εχω προηγουμενες παρτιδες με τετοιου ειδους προβληματα αποφασισα να ρωτησω την γνωμη σας επι του θεματος.
καθε αποψη δεκτή!