Αν και νέος χρήστης τα πηγαίνω πολύ καλά για την ώρα
Το πρόβλημα που έχω είναι με ενα usb tuner ΤV (crypto tv4all).
Έχω βάλει tvtime, xwtv αλλά τίποτα
η lsusb μου δίνει:
- Κώδικας: Επιλογή όλων
Bus 001 Device 005: ID 6000:0001
Bus 001 Device 003: ID 04f2:b084 Chicony Electronics Co., Ltd
Bus 001 Device 002: ID 0ace:1215 ZyDAS WLA-54L WiFi
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 002: ID 0a5c:2101 Broadcom Corp. A-Link BlueUsbA2 Bluetooth
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 003: ID 04d9:1133 Holtek Semiconductor, Inc.
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
ενω η dmesg
- Κώδικας: Επιλογή όλων
[ 0.961221] pci 0000:00:1b.0: PME# disabled
[ 0.961293] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.961300] pci 0000:00:1c.0: PME# disabled
[ 0.961375] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.961382] pci 0000:00:1c.1: PME# disabled
[ 0.961456] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.961464] pci 0000:00:1c.2: PME# disabled
[ 0.961534] pci 0000:00:1d.0: reg 20 io port: [0x50a0-0x50bf]
[ 0.961602] pci 0000:00:1d.1: reg 20 io port: [0x5080-0x509f]
[ 0.961669] pci 0000:00:1d.2: reg 20 io port: [0x5060-0x507f]
[ 0.961737] pci 0000:00:1d.3: reg 20 io port: [0x5040-0x505f]
[ 0.961808] pci 0000:00:1d.7: reg 10 32bit mmio: [0x56344400-0x563447ff]
[ 0.961859] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.961867] pci 0000:00:1d.7: PME# disabled
[ 0.962034] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[ 0.962042] pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
[ 0.962087] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
[ 0.962098] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
[ 0.962108] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
[ 0.962119] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
[ 0.962129] pci 0000:00:1f.1: reg 20 io port: [0x50c0-0x50cf]
[ 0.962197] pci 0000:00:1f.2: reg 10 io port: [0x50d8-0x50df]
[ 0.962208] pci 0000:00:1f.2: reg 14 io port: [0x50fc-0x50ff]
[ 0.962219] pci 0000:00:1f.2: reg 18 io port: [0x50d0-0x50d7]
[ 0.962230] pci 0000:00:1f.2: reg 1c io port: [0x50f8-0x50fb]
[ 0.962240] pci 0000:00:1f.2: reg 20 io port: [0x5020-0x502f]
[ 0.962251] pci 0000:00:1f.2: reg 24 32bit mmio: [0x56344000-0x563443ff]
[ 0.962275] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.962282] pci 0000:00:1f.2: PME# disabled
[ 0.962351] pci 0000:00:1f.3: reg 20 io port: [0x5000-0x501f]
[ 0.962505] pci 0000:01:00.0: reg 10 64bit mmio: [0x55100000-0x55103fff]
[ 0.962567] pci 0000:01:00.0: supports D1 D2
[ 0.962571] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.962580] pci 0000:01:00.0: PME# disabled
[ 0.962665] pci 0000:00:1c.0: bridge io port: [0x4000-0x4fff]
[ 0.962673] pci 0000:00:1c.0: bridge 32bit mmio: [0x55100000-0x561fffff]
[ 0.962684] pci 0000:00:1c.0: bridge 64bit mmio pref: [0x50000000-0x50ffffff]
[ 0.962750] pci 0000:00:1c.1: bridge io port: [0x3000-0x3fff]
[ 0.962758] pci 0000:00:1c.1: bridge 32bit mmio: [0x54100000-0x550fffff]
[ 0.962769] pci 0000:00:1c.1: bridge 64bit mmio pref: [0x51000000-0x51ffffff]
[ 0.962847] pci 0000:03:00.0: reg 10 64bit mmio: [0x53000000-0x5303ffff]
[ 0.962861] pci 0000:03:00.0: reg 18 io port: [0x1000-0x107f]
[ 0.962914] pci 0000:03:00.0: PME# supported from D3hot D3cold
[ 0.962923] pci 0000:03:00.0: PME# disabled
[ 0.962999] pci 0000:00:1c.2: bridge io port: [0x1000-0x2fff]
[ 0.963007] pci 0000:00:1c.2: bridge 32bit mmio: [0x53000000-0x540fffff]
[ 0.963018] pci 0000:00:1c.2: bridge 64bit mmio pref: [0x52000000-0x52ffffff]
[ 0.963092] pci 0000:00:1e.0: transparent bridge
[ 0.963135] bus 00 -> node 0
[ 0.963150] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.963781] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[ 0.964133] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
[ 0.964453] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
[ 0.970278] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.970561] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.970841] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.971117] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.971394] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.971672] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.971950] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.972245] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.972499] ACPI: Power Resource [FN00] (on)
[ 0.972855] ACPI: WMI: Mapper loaded
[ 0.972974] SCSI subsystem initialized
[ 0.972974] libata version 3.00 loaded.
[ 0.972974] usbcore: registered new interface driver usbfs
[ 0.972974] usbcore: registered new interface driver hub
[ 0.972974] usbcore: registered new device driver usb
[ 0.972974] PCI: Using ACPI for IRQ routing
[ 0.980020] Bluetooth: Core ver 2.13
[ 0.980060] NET: Registered protocol family 31
[ 0.980060] Bluetooth: HCI device and connection manager initialized
[ 0.980060] Bluetooth: HCI socket layer initialized
[ 0.980060] NET: Registered protocol family 8
[ 0.980060] NET: Registered protocol family 20
[ 0.980073] NetLabel: Initializing
[ 0.980077] NetLabel: domain hash size = 128
[ 0.980080] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.980104] NetLabel: unlabeled traffic allowed by default
[ 0.980134] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.980144] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.984110] AppArmor: AppArmor Filesystem Enabled
[ 0.988021] Switched to high resolution mode on CPU 0
[ 0.988381] Switched to high resolution mode on CPU 1
[ 0.992024] pnp: PnP ACPI init
[ 0.992046] ACPI: bus type pnp registered
[ 1.056848] pnp 00:01: io resource (0x164e-0x164f) overlaps 0000:00:1c.2 BAR 7 (0x1000-0x2fff), disabling
[ 1.058538] pnp: PnP ACPI: found 9 devices
[ 1.058543] ACPI: ACPI bus type pnp unregistered
[ 1.058549] PnPBIOS: Disabled by ACPI PNP
[ 1.058570] system 00:01: ioport range 0x200-0x20f has been reserved
[ 1.058577] system 00:01: ioport range 0x600-0x60f has been reserved
[ 1.058582] system 00:01: ioport range 0x610-0x610 has been reserved
[ 1.058588] system 00:01: ioport range 0x800-0x80f has been reserved
[ 1.058593] system 00:01: ioport range 0x400-0x47f has been reserved
[ 1.058599] system 00:01: ioport range 0x500-0x53f has been reserved
[ 1.058605] system 00:01: ioport range 0xff2c-0xff2f has been reserved
[ 1.058612] system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
[ 1.058619] system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 1.058625] system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
[ 1.058631] system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
[ 1.058637] system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
[ 1.058643] system 00:01: iomem range 0xfec00000-0xfec00fff has been reserved
[ 1.058649] system 00:01: iomem range 0xfee00000-0xfee00fff has been reserved
[ 1.093568] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01
[ 1.093576] pci 0000:00:1c.0: IO window: 0x4000-0x4fff
[ 1.093586] pci 0000:00:1c.0: MEM window: 0x55100000-0x561fffff
[ 1.093594] pci 0000:00:1c.0: PREFETCH window: 0x00000050000000-0x00000050ffffff
[ 1.093605] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02
[ 1.093611] pci 0000:00:1c.1: IO window: 0x3000-0x3fff
[ 1.093620] pci 0000:00:1c.1: MEM window: 0x54100000-0x550fffff
[ 1.093628] pci 0000:00:1c.1: PREFETCH window: 0x00000051000000-0x00000051ffffff
[ 1.093640] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:03
[ 1.093646] pci 0000:00:1c.2: IO window: 0x1000-0x2fff
[ 1.093655] pci 0000:00:1c.2: MEM window: 0x53000000-0x540fffff
[ 1.093662] pci 0000:00:1c.2: PREFETCH window: 0x00000052000000-0x00000052ffffff
[ 1.093674] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:04
[ 1.093678] pci 0000:00:1e.0: IO window: disabled
[ 1.093686] pci 0000:00:1e.0: MEM window: disabled
[ 1.093692] pci 0000:00:1e.0: PREFETCH window: disabled
[ 1.093720] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.093729] pci 0000:00:1c.0: setting latency timer to 64
[ 1.093741] pci 0000:00:1c.1: enabling device (0000 -> 0003)
[ 1.093750] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.093759] pci 0000:00:1c.1: setting latency timer to 64
[ 1.093774] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.093781] pci 0000:00:1c.2: setting latency timer to 64
[ 1.093793] pci 0000:00:1e.0: setting latency timer to 64
[ 1.093800] bus: 00 index 0 io port: [0x00-0xffff]
[ 1.093805] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[ 1.093810] bus: 01 index 0 io port: [0x4000-0x4fff]
[ 1.093814] bus: 01 index 1 mmio: [0x55100000-0x561fffff]
[ 1.093819] bus: 01 index 2 mmio: [0x50000000-0x50ffffff]
[ 1.093823] bus: 01 index 3 mmio: [0x0-0x0]
[ 1.093828] bus: 02 index 0 io port: [0x3000-0x3fff]
[ 1.093832] bus: 02 index 1 mmio: [0x54100000-0x550fffff]
[ 1.093837] bus: 02 index 2 mmio: [0x51000000-0x51ffffff]
[ 1.093841] bus: 02 index 3 mmio: [0x0-0x0]
[ 1.093845] bus: 03 index 0 io port: [0x1000-0x2fff]
[ 1.093850] bus: 03 index 1 mmio: [0x53000000-0x540fffff]
[ 1.093854] bus: 03 index 2 mmio: [0x52000000-0x52ffffff]
[ 1.093858] bus: 03 index 3 mmio: [0x0-0x0]
[ 1.093862] bus: 04 index 0 mmio: [0x0-0x0]
[ 1.093866] bus: 04 index 1 mmio: [0x0-0x0]
[ 1.093870] bus: 04 index 2 mmio: [0x0-0x0]
[ 1.093874] bus: 04 index 3 io port: [0x00-0xffff]
[ 1.093878] bus: 04 index 4 mmio: [0x000000-0xffffffff]
[ 1.093899] NET: Registered protocol family 2
[ 1.108126] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 1.108639] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 1.109461] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 1.109889] TCP: Hash tables configured (established 131072 bind 65536)
[ 1.109895] TCP reno registered
[ 1.116173] NET: Registered protocol family 1
[ 1.116382] checking if image is initramfs... it is
[ 2.050934] Freeing initrd memory: 7378k freed
[ 2.050999] Simple Boot Flag value 0x5 read from CMOS RAM was invalid
[ 2.051004] Simple Boot Flag at 0x44 set to 0x1
[ 2.051341] cpufreq: No nForce2 chipset.
[ 2.051602] audit: initializing netlink socket (disabled)
[ 2.051639] type=2000 audit(1259825373.048:1): initialized
[ 2.065461] highmem bounce pool size: 64 pages
[ 2.065471] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 2.068141] VFS: Disk quotas dquot_6.5.1
[ 2.068261] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.069550] fuse init (API version 7.10)
[ 2.069733] msgmni has been set to 1724
[ 2.070073] alg: No test for stdrng (krng)
[ 2.070104] io scheduler noop registered
[ 2.070108] io scheduler anticipatory registered
[ 2.070112] io scheduler deadline registered
[ 2.070148] io scheduler cfq registered (default)
[ 2.070170] pci 0000:00:02.0: Boot video device
[ 2.070640] ACPI Error (dsfield-0139): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[ 2.070654] ACPI Error (psparse-0524): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f6c16a50), AE_ALREADY_EXISTS
[ 2.070669] ACPI: Marking method _OSC as Serialized because of AE_ALREADY_EXISTS error
[ 2.133810] ACPI Error (dsfield-0139): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[ 2.133823] ACPI Error (psparse-0524): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f6c16a50), AE_ALREADY_EXISTS
[ 2.197758] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 2.197814] pcieport-driver 0000:00:1c.0: found MSI capability
[ 2.197858] pcieport-driver 0000:00:1c.0: irq 2303 for MSI/MSI-X
[ 2.197877] pci_express 0000:00:1c.0:pcie00: allocate port service
[ 2.197916] pci_express 0000:00:1c.0:pcie02: allocate port service
[ 2.197942] pci_express 0000:00:1c.0:pcie03: allocate port service
[ 2.198033] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[ 2.198087] pcieport-driver 0000:00:1c.1: found MSI capability
[ 2.198125] pcieport-driver 0000:00:1c.1: irq 2302 for MSI/MSI-X
[ 2.198144] pci_express 0000:00:1c.1:pcie00: allocate port service
[ 2.198172] pci_express 0000:00:1c.1:pcie02: allocate port service
[ 2.198197] pci_express 0000:00:1c.1:pcie03: allocate port service
[ 2.198288] pcieport-driver 0000:00:1c.2: setting latency timer to 64
[ 2.198341] pcieport-driver 0000:00:1c.2: found MSI capability
[ 2.198379] pcieport-driver 0000:00:1c.2: irq 2301 for MSI/MSI-X
[ 2.198397] pci_express 0000:00:1c.2:pcie00: allocate port service
[ 2.198425] pci_express 0000:00:1c.2:pcie02: allocate port service
[ 2.198450] pci_express 0000:00:1c.2:pcie03: allocate port service
[ 2.198566] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 2.198747] ACPI Error (dsfield-0139): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[ 2.198760] ACPI Error (psparse-0524): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f6c16a50), AE_ALREADY_EXISTS
[ 2.199051] ACPI Error (dsfield-0139): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[ 2.199063] ACPI Error (psparse-0524): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f6c16a50), AE_ALREADY_EXISTS
[ 2.199344] ACPI Error (dsfield-0139): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[ 2.199357] ACPI Error (psparse-0524): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f6c16a50), AE_ALREADY_EXISTS
[ 2.199496] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 2.260163] ACPI: AC Adapter [AC] (on-line)
[ 2.324096] ACPI: Battery Slot [BAT0] (battery absent)
[ 2.324234] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 2.324240] ACPI: Power Button (FF) [PWRF]
[ 2.324328] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 2.324334] ACPI: Power Button (CM) [PWRB]
[ 2.324427] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[ 2.324527] ACPI: Lid Switch [LID0]
[ 2.324625] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3
[ 2.324631] ACPI: Sleep Button (CM) [SLPB]
[ 2.325050] fan PNP0C0B:00: registered as cooling_device0
[ 2.325061] ACPI: Fan [FAN] (on)
[ 2.326124] ACPI: SSDT 3F592C90, 01F7 (r2 PmRef Cpu0Ist 3000 INTL 20051117)
[ 2.326866] ACPI: SSDT 3F591E10, 01C7 (r2 PmRef Cpu0Cst 3001 INTL 20051117)
[ 2.328572] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 2.328613] processor ACPI_CPU:00: registered as cooling_device1
[ 2.328621] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 2.329308] ACPI: SSDT 3F592F10, 00D0 (r2 PmRef Cpu1Ist 3000 INTL 20051117)
[ 2.330017] ACPI: SSDT 3F590F10, 0083 (r2 PmRef Cpu1Cst 3000 INTL 20051117)
[ 2.331794] ACPI: CPU1 (power states: C1[C1] C2[C2])
[ 2.331833] processor ACPI_CPU:01: registered as cooling_device2
[ 2.331841] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 2.398949] thermal LNXTHERM:01: registered as thermal_zone0
[ 2.399133] ACPI: Thermal Zone [THRM] (27 C)
[ 2.399225] isapnp: Scanning for PnP cards...
[ 2.753006] isapnp: No Plug & Play device found
[ 2.768524] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 2.770372] brd: module loaded
[ 2.771006] loop: module loaded
[ 2.771171] Fixed MDIO Bus: probed
[ 2.771182] PPP generic driver version 2.4.2
[ 2.771302] input: Macintosh mouse button emulation as /devices/virtual/input/input4
[ 2.771362] Driver 'sd' needs updating - please use bus_type methods
[ 2.771381] Driver 'sr' needs updating - please use bus_type methods
[ 2.771464] ahci 0000:00:1f.2: version 3.0
[ 2.771488] ahci 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 2.771572] ahci 0000:00:1f.2: irq 2300 for MSI/MSI-X
[ 2.771680] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x5 impl SATA mode
[ 2.771687] ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pio slum part
[ 2.771696] ahci 0000:00:1f.2: setting latency timer to 64
[ 2.772061] scsi0 : ahci
[ 2.772294] scsi1 : ahci
[ 2.772430] scsi2 : ahci
[ 2.772568] scsi3 : ahci
[ 2.772863] ata1: SATA max UDMA/133 abar m1024@0x56344000 port 0x56344100 irq 2300
[ 2.772869] ata2: DUMMY
[ 2.772874] ata3: SATA max UDMA/133 abar m1024@0x56344000 port 0x56344200 irq 2300
[ 2.772878] ata4: DUMMY
[ 3.092035] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3.093299] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
[ 3.093470] ata1.00: ATA-8: Hitachi HTS543216L9SA00, FB2OC40C, max UDMA/133
[ 3.093477] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 3.094858] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
[ 3.095065] ata1.00: configured for UDMA/133
[ 3.428032] ata3: SATA link down (SStatus 0 SControl 300)
[ 3.444217] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54321 FB2O PQ: 0 ANSI: 5
[ 3.444437] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
[ 3.444480] sd 0:0:0:0: [sda] Write Protect is off
[ 3.444485] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.444553] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.444689] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
[ 3.444727] sd 0:0:0:0: [sda] Write Protect is off
[ 3.444733] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.444799] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.444807] sda: sda1 sda2 sda4 < sda5 sda6 >
[ 3.489666] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.489772] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.489873] ata_piix 0000:00:1f.1: version 2.12
[ 3.489892] ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.489946] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 3.490112] scsi4 : ata_piix
[ 3.490258] scsi5 : ata_piix
[ 3.491327] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x50c0 irq 14
[ 3.491333] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x50c8 irq 15
[ 3.644131] ata6: port disabled. ignoring.
[ 3.645537] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.645574] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.645607] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 3.645614] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 3.645735] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 3.649672] ehci_hcd 0000:00:1d.7: debug port 1
[ 3.649682] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 3.649710] ehci_hcd 0000:00:1d.7: irq 16, io mem 0x56344400
[ 3.664021] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 3.664162] usb usb1: configuration #1 chosen from 1 choice
[ 3.664217] hub 1-0:1.0: USB hub found
[ 3.664232] hub 1-0:1.0: 8 ports detected
[ 3.664443] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.664480] uhci_hcd: USB Universal Host Controller Interface driver
[ 3.664542] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.664555] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 3.664561] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 3.664650] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 3.664684] uhci_hcd 0000:00:1d.0: irq 16, io base 0x000050a0
[ 3.664829] usb usb2: configuration #1 chosen from 1 choice
[ 3.664880] hub 2-0:1.0: USB hub found
[ 3.664893] hub 2-0:1.0: 2 ports detected
[ 3.665052] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 3.665063] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 3.665069] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 3.665152] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 3.665200] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00005080
[ 3.665340] usb usb3: configuration #1 chosen from 1 choice
[ 3.665397] hub 3-0:1.0: USB hub found
[ 3.665410] hub 3-0:1.0: 2 ports detected
[ 3.665568] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 3.665579] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 3.665585] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.665669] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 3.665714] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00005060
[ 3.665866] usb usb4: configuration #1 chosen from 1 choice
[ 3.665918] hub 4-0:1.0: USB hub found
[ 3.665931] hub 4-0:1.0: 2 ports detected
[ 3.666098] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 3.666109] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 3.666115] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 3.666199] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 3.666243] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00005040
[ 3.666399] usb usb5: configuration #1 chosen from 1 choice
[ 3.666452] hub 5-0:1.0: USB hub found
[ 3.666466] hub 5-0:1.0: 2 ports detected
[ 3.666727] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSS0] at 0x60,0x64 irq 1,12
[ 3.705192] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.705205] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 3.708093] mice: PS/2 mouse device common for all mice
[ 3.728134] rtc_cmos 00:03: RTC can wake from S4
[ 3.728205] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 3.728249] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 3.728397] device-mapper: uevent: version 1.0.3
[ 3.728623] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 3.728800] device-mapper: multipath: version 1.0.5 loaded
[ 3.728806] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 3.729019] EISA: Probing bus 0 at eisa.0
[ 3.729032] Cannot allocate resource for EISA slot 1
[ 3.729037] Cannot allocate resource for EISA slot 2
[ 3.729042] Cannot allocate resource for EISA slot 3
[ 3.729046] Cannot allocate resource for EISA slot 4
[ 3.729050] Cannot allocate resource for EISA slot 5
[ 3.729070] EISA: Detected 0 cards.
[ 3.729298] cpuidle: using governor ladder
[ 3.729465] cpuidle: using governor menu
[ 3.730477] TCP cubic registered
[ 3.730694] NET: Registered protocol family 10
[ 3.731490] lo: Disabled Privacy Extensions
[ 3.732165] NET: Registered protocol family 17
[ 3.732206] Bluetooth: L2CAP ver 2.11
[ 3.732210] Bluetooth: L2CAP socket layer initialized
[ 3.732216] Bluetooth: SCO (Voice Link) ver 0.6
[ 3.732219] Bluetooth: SCO socket layer initialized
[ 3.732291] Marking TSC unstable due to TSC halts in idle
[ 3.732310] Bluetooth: RFCOMM socket layer initialized
[ 3.732323] Bluetooth: RFCOMM TTY layer initialized
[ 3.732327] Bluetooth: RFCOMM ver 1.10
[ 3.734179] Using IPI No-Shortcut mode
[ 3.734345] registered taskstats version 1
[ 3.734584] Magic number: 5:926:469
[ 3.734710] rtc_cmos 00:03: setting system clock to 2009-12-03 07:29:35 UTC (1259825375)
[ 3.734718] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 3.734722] EDD information not available.
[ 3.735111] Freeing unused kernel memory: 532k freed
[ 3.735404] Write protecting the kernel text: 4120k
[ 3.735510] Write protecting the kernel read-only data: 1524k
[ 3.753704] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 3.977044] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 4.147187] usb 1-1: configuration #1 chosen from 1 choice
[ 4.255321] ATL1E 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 4.255345] ATL1E 0000:03:00.0: setting latency timer to 64
[ 4.256765] usb 1-2: new high speed USB device using ehci_hcd and address 3
[ 4.562375] usb 1-2: configuration #1 chosen from 1 choice
[ 4.744085] usb 1-4: new high speed USB device using ehci_hcd and address 5
[ 4.844434] PM: Starting manual resume from disk
[ 4.844443] PM: Resume from partition 8:5
[ 4.844446] PM: Checking hibernation image.
[ 4.844733] PM: Resume from disk failed.
[ 4.885722] usb 1-4: configuration #1 chosen from 1 choice
[ 4.885747] kjournald starting. Commit interval 5 seconds
[ 4.885777] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.128106] usb 3-1: new low speed USB device using uhci_hcd and address 2
[ 5.320592] usb 3-1: configuration #1 chosen from 1 choice
[ 11.085812] udev: starting version 141
[ 11.294895] ieee80211_crypt: registered algorithm 'NULL'
[ 11.300960] wl: module license 'MIXED/Proprietary' taints kernel.
[ 11.308521] wl 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 11.308538] wl 0000:01:00.0: setting latency timer to 64
[ 11.342596] Linux agpgart interface v0.103
[ 11.418009] ieee80211_crypt: registered algorithm 'TKIP'
[ 11.418979] eth1: Broadcom BCM4315 802.11 Wireless Controller 5.10.91.9
[ 11.541339] agpgart-intel 0000:00:00.0: Intel 945GME Chipset
[ 11.541699] agpgart-intel 0000:00:00.0: detected 7932K stolen memory
[ 11.545100] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x40000000
[ 11.606188] intel_rng: FWH not detected
[ 11.692184] usbcore: registered new interface driver hiddev
[ 11.726281] input: HID 04d9:1133 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input6
[ 11.756176] cfg80211: Calling CRDA to update world regulatory domain
[ 11.758241] generic-usb 0003:04D9:1133.0001: input,hidraw0: USB HID v1.10 Mouse [HID 04d9:1133] on usb-0000:00:1d.1-1/input0
[ 11.758314] usbcore: registered new interface driver usbhid
[ 11.758397] usbhid: v2.6:USB HID core driver
[ 11.825256] acpi device:1a: registered as cooling_device3
[ 11.826304] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:16/input/input7
[ 11.856267] ACPI: Video Device [OVGA] (multi-head: yes rom: yes post: no)
[ 11.885817] input: PC Speaker as /devices/platform/pcspkr/input/input8
[ 11.953499] Linux video capture interface: v2.00
[ 12.003187] iTCO_vendor_support: vendor-support=0
[ 12.025832] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 12.026301] iTCO_wdt: Found a ICH7-M or ICH7-U TCO device (Version=2, TCOBASE=0x0460)
[ 12.026808] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 12.194218] cfg80211: World regulatory domain updated:
[ 12.194229] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.194238] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.194246] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.194253] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.194261] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.194269] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.386732] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[ 12.540789] acer-wmi: Acer Laptop ACPI-WMI Extras
[ 12.631059] uvcvideo: Found UVC 1.00 device Webcam (04f2:b084)
[ 12.632609] input: Webcam as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2:1.0/input/input9
[ 12.633427] usbcore: registered new interface driver uvcvideo
[ 12.633503] USB Video Class driver (v0.1.0)
[ 12.670818] acer-wmi: Unable to detect available WMID devices
[ 12.896087] usb 1-1: reset high speed USB device using ehci_hcd and address 2
[ 12.975961] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 12.976153] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 13.009982] hda_codec: Unknown model for ALC662, trying auto-probe from BIOS...
[ 13.031091] phy0: Selected rate control algorithm 'pid'
[ 13.104848] zd1211rw 1-1:1.0: phy0
[ 13.104956] usbcore: registered new interface driver zd1211rw
[ 13.386186] lp: driver loaded but no devices found
[ 13.550656] Adding 2273156k swap on /dev/sda5. Priority:-1 extents:1 across:2273156k
[ 13.610164] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04771/0xa40000
[ 13.716974] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input10
[ 14.245845] EXT3 FS on sda6, internal journal
[ 15.690569] type=1505 audit(1259818187.453:2): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2069
[ 15.690839] type=1505 audit(1259818187.453:3): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2069
[ 15.690954] type=1505 audit(1259818187.453:4): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2069
[ 15.691049] type=1505 audit(1259818187.453:5): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2069
[ 15.994540] type=1505 audit(1259818187.758:6): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2074
[ 15.994937] type=1505 audit(1259818187.758:7): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2074
[ 16.056472] type=1505 audit(1259818187.818:8): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2078
[ 20.984315] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 20.984323] Bluetooth: BNEP filters: protocol multicast
[ 21.017198] Bridge firewalling registered
[ 22.522309] ppdev: user-space parallel port driver
[ 23.804134] [drm] Initialized drm 1.1.0 20060810
[ 23.829472] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 23.829486] pci 0000:00:02.0: setting latency timer to 64
[ 23.829873] [drm] Initialized i915 1.6.0 20080730 on minor 0
[ 23.931735] [drm:i915_setparam] *ERROR* unknown parameter 4
[ 23.931811] [drm:i915_getparam] *ERROR* Unknown parameter 6
[ 25.136590] [drm:i915_getparam] *ERROR* Unknown parameter 6
[ 26.236413] ATL1E 0000:03:00.0: irq 2299 for MSI/MSI-X
[ 26.237133] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 26.239641] usb 1-1: firmware: requesting zd1211/zd1211b_ub
[ 26.421810] usb 1-1: firmware: requesting zd1211/zd1211b_uphr
[ 26.566424] zd1211rw 1-1:1.0: firmware version 4725
[ 26.607442] zd1211rw 1-1:1.0: zd1211b chip 0ace:1215 v4810 high 00-21-27 MAXIM_NEW_RF pa0 -7---
[ 26.610211] cfg80211: Calling CRDA for country: DE
[ 26.617113] cfg80211: Regulatory domain changed to country: DE
[ 26.617123] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 26.617132] (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 26.617139] (5150000 KHz - 5255000 KHz @ 40000 KHz), (N/A, 2301 mBm)
[ 26.617147] (5470000 KHz - 5650000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 26.643552] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 27.715789] wlan0: authenticate with AP 00:1c:a2:ab:5d:c5
[ 27.717374] wlan0: authenticated
[ 27.717385] wlan0: associate with AP 00:1c:a2:ab:5d:c5
[ 27.719617] wlan0: RX AssocResp from 00:1c:a2:ab:5d:c5 (capab=0x461 status=0 aid=1)
[ 27.719627] wlan0: associated
[ 27.720663] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 27.738725] wlan0: disassociating by local choice (reason=3)
[ 31.025065] eth1: no IPv6 routers present
[ 37.820039] wlan0: no IPv6 routers present
[ 48.449291] wlan0: authenticate with AP 00:1c:a2:ab:5d:c5
[ 48.470916] wlan0: authenticate with AP 00:1c:a2:ab:5d:c5
[ 48.470962] wlan0: authenticated
[ 48.470971] wlan0: associate with AP 00:1c:a2:ab:5d:c5
[ 48.475041] wlan0: RX ReassocResp from 00:1c:a2:ab:5d:c5 (capab=0x461 status=0 aid=1)
[ 48.475051] wlan0: associated
[ 178.333952] wlan0: authenticate with AP 00:1c:a2:ab:5d:c5
[ 178.355726] wlan0: authenticate with AP 00:1c:a2:ab:5d:c5
[ 178.355773] wlan0: authenticated
[ 178.355784] wlan0: associate with AP 00:1c:a2:ab:5d:c5
[ 178.359437] wlan0: RX ReassocResp from 00:1c:a2:ab:5d:c5 (capab=0x461 status=0 aid=1)
[ 178.359448] wlan0: associated
[ 261.048168] usb 3-1: USB disconnect, address 2
[ 333.500101] usb 3-1: new low speed USB device using uhci_hcd and address 3
[ 333.689013] usb 3-1: configuration #1 chosen from 1 choice
[ 333.741574] input: HID 04d9:1133 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input11
[ 333.769976] generic-usb 0003:04D9:1133.0002: input,hidraw0: USB HID v1.10 Mouse [HID 04d9:1133] on usb-0000:00:1d.1-1/input0
[ 1022.047242] [drm:i915_getparam] *ERROR* Unknown parameter 6
[ 2758.308972] wlan0: authenticate with AP 00:1c:a2:ab:5d:c5
[ 2758.329966] wlan0: authenticate with AP 00:1c:a2:ab:5d:c5
[ 2758.330003] wlan0: authenticated
[ 2758.330014] wlan0: associate with AP 00:1c:a2:ab:5d:c5
[ 2758.333828] wlan0: RX ReassocResp from 00:1c:a2:ab:5d:c5 (capab=0x461 status=0 aid=1)
[ 2758.333838] wlan0: associated
[ 3247.959594] [drm:i915_getparam] *ERROR* Unknown parameter 6
[ 3934.128075] usb 5-1: new full speed USB device using uhci_hcd and address 2
[ 3934.299334] usb 5-1: configuration #1 chosen from 1 choice
[ 3934.356431] Bluetooth: Generic Bluetooth USB driver ver 0.3
[ 3934.356619] usbcore: registered new interface driver btusb
εδώ σηκώνω τα χέρια ψηλά
όποιος μπορεί να βοηθήσει τον ευχαριστώ
