crypto tvr usb 2

[tolmas]

αν δεν το εχω βαλει εγω εκει που θα επρεπε να ειναι αυτο το αρχειο???
στα μισα που εχω σχεδον δοκιμασει μου βγαζει συνεχεια το ιδιο.
????
καθε φορα πρεπει κ τις 2 εντολες η μετα την πρωτη δεν ξαναχρειαζετε, παταω δηλαδη την 2η με αλλο αριθμο?

[logari81]

καθε φορα πρεπει κ τις 2 εντολες

ναι και τις 2. Αν δεν εισαι σιγουρος κανε copy paste ολο το τερματικο με τις εντολες σου και τα αποτελεσματα εδω και θα σου πούμε.

[tolmas]

Κώδικας: Επιλογή όλων

tolis@tolis-laptop:~$ sudo modprobe -r em28xx
[sudo] password for tolis:
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=2
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=3
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=4
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=5
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=6
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=7
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=8
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=9
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=10
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
[sudo] password for tolis:
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sodo modprobe em28xx card=11
No command 'sodo' found, did you mean:
Command 'todo' from package 'devtodo' (universe)
Command 'solo' from package 'sgt-puzzles' (universe)
Command 'sudo' from package 'sudo' (main)
Command 'sudo' from package 'sudo-ldap' (universe)
sodo: command not found
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=12
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=13
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=14
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=15
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=15
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=16
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=17
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=18
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=19
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=20
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=21
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=22
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=23
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=24
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=25
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=26
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=27
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=28
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=29
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=30
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=31
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=32
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=33
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=34
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
FATAL: Module em28xx is in use.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=35
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=36
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=37
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=38
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=39
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=40
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=41
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=42
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=43
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=44
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=44
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=45
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=46
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=47
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=48
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=49
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=50
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$
tolis@tolis-laptop:~$
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=51
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=52
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=53
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=54
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=55
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=56
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=57
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=58
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=59
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=60
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=61
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=62
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=63
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=64
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=65
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=66
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=67
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=68
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=69
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=70
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe -r em28xx
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.
tolis@tolis-laptop:~$ sudo modprobe em28xx card=71
WARNING: All config files need .conf: /etc/modprobe.d/blacklist-userful, it will be ignored in a future release.


το ιδιο παντου.....

[logari81]

εκτος απο το νουμερο 11 και το νουμερο 35 στα οποια εκανες καποια λαθη, ολα τα αλλα τα εκανες σωστα. Μετα απο καθε νουμερο δοκιμαζες το tvtime και δεν ειχε σε κανενα νουμερο καποια εικόνα;

Επίσης για δωσε μας το αποτελεσμα του

Κώδικας: Επιλογή όλων

cat /etc/modprobe.d/blacklist-userful

[tolmas]

Κώδικας: Επιλογή όλων

~$ cat /etc/modprobe.d/blacklist-userful
blacklist pcspkr
blacklist button


no signal, no input available device
cannot open capture device /dev/video0
κ αυτα το tvtime

[logari81]

χμ, ισως να μην καναμε κατι σωστα. Θα το ξανακοιταξω και θα σου πω.

Καποιος που ξερει γερμανικα ας μεταφρασει αυτο
http://wiki.ubuntuusers.de/em28xx
γιατι δεν εχω χρονο αυτες τις μερες να το κανω

[tolmas]

θα το ριξω μια ματια κ γω το λινκ που δινεις
ειχα διαβασει σε ενα φορουμ για το πως αλλαζε το video0 σε 1 η 2. σε ποιο ακριβως δεν θυμαμαι να το ξαναβρω.
Θα μπορουσε να μας βοηθησει σε τπτ???

[tolmas]

Λοιπον, κανω εγκατασταση build-essential,linux-source και linux-headers-*. Μετα δινω

Κώδικας: Επιλογή όλων

cd /lib/modules/$(uname -r)/
sudo ln --symbolic /usr/src/linux-headers-$(uname -r)/ build

μετα μας λεει να αντιγρψουμε μερικα αρχεια απο το linux-source (/usr/scr/linux-headers-2.6.27-9-generic/drivers/media/dvb/dvb-core/ bzw. /usr/scr/linux-headers-2.6.27-9-generic/drivers/media/dvb/frontends/ ) κ στις επομενες εντολες λεει

Κώδικας: Επιλογή όλων

tolis@tolis-laptop:~$ cd /usr/src
tolis@tolis-laptop:/usr/src$ sudo cp linux-source-2.6.31/drivers/media/dvb/dvb-core/*.h linux-headers-$(uname -r)/drivers/media/dvb/dvb-core/
[sudo] password for tolis:
cp: αδύνατη η εκτέλεση της stat στο αρχείο «linux-source-2.6.31/drivers/media/dvb/dvb-core/*.h»: No such file or directory
tolis@tolis-laptop:/usr/src$


κ το αφησα.
Παρακατω (em28xx-new-Paket ab Intrepid) γρφει μια πιο απλη μεθοδο, να κατεβασω απο εδω http://jiemeb.free.fr/pinnacle/ gia το καταλληλο kernel, αλλα δεν υπαρχει για 31-20 κ κατεβασα για 31-19.το κανω εγγατασταση κ το tvtime δουλεψε κ εψαξε για καναλια κ δεν βρικε τπτ. μετα εκανα επανεκκινηση κ δε δουλευε.....
Κοιτα κ αυτο να μου πεις http://www.linuxtv.org/wiki/index.php/Em28xx_devices

[logari81]

απεγκατεστησε λιγο το πακετο που εβαλες για να κανουμε μια αλλη δοκιμη πρώτα.
Το πρωτο που εννοουσα να δοκιμασουμε είναι μήπως λειπει όντως το firmware για να το κατεβασεις και να το εγκαταστησεις τρεχεις τις εντολες

Κώδικας: Επιλογή όλων

wget http://www.steventoth.net/linux/xc5000/HVR-12x0-14x0-17x0_1_25_25271_WHQL.zip
unzip -j HVR-12x0-14x0-17x0_1_25_25271_WHQL.zip Driver85/hcw85bda.sys
wget http://linuxtv.org/hg/v4l-dvb/raw-file/6bab82c6096e/linux/Documentation/video4linux/extract_xc3028.pl
sudo chmod a+x extract_xc3028.pl
sudo ./extract_xc3028.pl
sudo cp xc3028-v27.fw /lib/firmware

και μετα κανεις επανεκκινηση και μας δινεις το αποτελεσμα του

Κώδικας: Επιλογή όλων

dmesg

[tolmas]

απεγκατεστησε λιγο το πακετο που εβαλες για να κανουμε μια αλλη δοκιμη πρώτα.

εννοεις το em28xx?

Κώδικας: Επιλογή όλων

[ 0.867118] ehci_hcd 0000:00:03.3: EHCI Host Controller
[ 0.867150] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
[ 0.867180] ehci_hcd 0000:00:03.3: debug port 1
[ 0.867202] ehci_hcd 0000:00:03.3: irq 22, io mem 0xd4206000
[ 0.877012] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00
[ 0.877097] usb usb1: configuration #1 chosen from 1 choice
[ 0.877126] hub 1-0:1.0: USB hub found
[ 0.877135] hub 1-0:1.0: 8 ports detected
[ 0.877197] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.877214] alloc irq_desc for 20 on node -1
[ 0.877216] alloc kstat_irqs on node -1
[ 0.877222] ohci_hcd 0000:00:03.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.877234] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 0.877265] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
[ 0.877284] ohci_hcd 0000:00:03.0: irq 20, io mem 0xd4204000
[ 0.936042] usb usb2: configuration #1 chosen from 1 choice
[ 0.936068] hub 2-0:1.0: USB hub found
[ 0.936078] hub 2-0:1.0: 4 ports detected
[ 0.936124] alloc irq_desc for 21 on node -1
[ 0.936126] alloc kstat_irqs on node -1
[ 0.936130] ohci_hcd 0000:00:03.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.936140] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 0.936173] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
[ 0.936190] ohci_hcd 0000:00:03.1: irq 21, io mem 0xd4205000
[ 0.990065] usb usb3: configuration #1 chosen from 1 choice
[ 0.990094] hub 3-0:1.0: USB hub found
[ 0.990102] hub 3-0:1.0: 4 ports detected
[ 0.990151] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.990247] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.994010] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 0.996386] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.996392] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.996396] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.996399] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.996402] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.996474] mice: PS/2 mouse device common for all mice
[ 0.996613] rtc_cmos 00:02: RTC can wake from S4
[ 0.996651] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 0.996673] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[ 0.996778] device-mapper: uevent: version 1.0.3
[ 0.996870] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.996940] device-mapper: multipath: version 1.1.0 loaded
[ 0.996943] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.997061] EISA: Probing bus 0 at eisa.0
[ 0.997068] Cannot allocate resource for EISA slot 1
[ 0.997074] Cannot allocate resource for EISA slot 3
[ 0.997076] Cannot allocate resource for EISA slot 4
[ 0.997089] Cannot allocate resource for EISA slot 8
[ 0.997091] EISA: Detected 0 cards.
[ 0.997240] cpuidle: using governor ladder
[ 0.997337] cpuidle: using governor menu
[ 0.997867] TCP cubic registered
[ 0.998026] NET: Registered protocol family 10
[ 0.998506] lo: Disabled Privacy Extensions
[ 0.998852] NET: Registered protocol family 17
[ 0.998872] Bluetooth: L2CAP ver 2.13
[ 0.998874] Bluetooth: L2CAP socket layer initialized
[ 0.998877] Bluetooth: SCO (Voice Link) ver 0.6
[ 0.998878] Bluetooth: SCO socket layer initialized
[ 0.998918] Bluetooth: RFCOMM TTY layer initialized
[ 0.998922] Bluetooth: RFCOMM socket layer initialized
[ 0.998924] Bluetooth: RFCOMM ver 1.11
[ 0.999335] Using IPI No-Shortcut mode
[ 0.999407] PM: Resume from disk failed.
[ 0.999421] registered taskstats version 1
[ 0.999526] Magic number: 2:716:326
[ 0.999576] pata_sis 0000:00:02.5: hash matches
[ 0.999622] rtc_cmos 00:02: setting system clock to 2010-03-04 11:20:29 UTC (1267701629)
[ 0.999625] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.999627] EDD information not available.
[ 1.028256] ata3.00: ATAPI: HL-DT-ST DVDRAM GSA-T40N, JW02, max UDMA/33
[ 1.032759] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 1.044273] ata3.00: configured for UDMA/33
[ 1.115386] ata1.00: ATA-8: WDC WD1600BEVT-22ZCT0, 11.01A11, max UDMA/133
[ 1.115389] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.128700] ata1.00: configured for UDMA/133
[ 1.128828] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVT-2 11.0 PQ: 0 ANSI: 5
[ 1.128962] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.129008] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 1.129057] sd 0:0:0:0: [sda] Write Protect is off
[ 1.129060] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.129084] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.129216] sda: sda1 sda2 < sda5 >
[ 1.166396] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.297803] scsi 2:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T40N JW02 PQ: 0 ANSI: 5
[ 1.301022] usb 1-3: new high speed USB device using ehci_hcd and address 3
[ 1.301302] sr0: scsi3-mmc drive: 62x/62x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.301306] Uniform CD-ROM driver Revision: 3.20
[ 1.301401] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 1.301450] sr 2:0:0:0: Attached scsi generic sg1 type 5
[ 1.301495] ata4: port disabled. ignoring.
[ 1.301524] Freeing unused kernel memory: 540k freed
[ 1.301892] Write protecting the kernel text: 4580k
[ 1.301940] Write protecting the kernel read-only data: 1840k
[ 1.424762] Linux agpgart interface v0.103
[ 1.427402] agpgart-sis 0000:00:00.0: SiS chipset [1039/0671]
[ 1.436764] agpgart-sis 0000:00:00.0: AGP aperture is 64M @ 0xd0000000
[ 1.451518] usb 1-3: configuration #1 chosen from 1 choice
[ 1.454453] [Firmware Bug]: ACPI: ACPI brightness control misses _BQC function
[ 1.454661] acpi device:04: registered as cooling_device2
[ 1.454767] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:01/device:02/input/input6
[ 1.454815] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 1.457256] hub 1-3:1.0: USB hub found
[ 1.458464] hub 1-3:1.0: 4 ports detected
[ 1.530339] sr0: CDROM (ioctl) error, command: Read TOC/PMA/ATIP 43 00 00 00 00 00 00 00 0c 40
[ 1.530354] sr: Sense Key : Medium Error [current]
[ 1.530358] sr: Add. Sense: Unable to recover table-of-contents
[ 1.534468] sr0: CDROM (ioctl) error, command: Read TOC/PMA/ATIP 43 00 00 00 00 00 00 00 0c 00
[ 1.534482] sr: Sense Key : Medium Error [current]
[ 1.534486] sr: Add. Sense: Unable to recover table-of-contents
[ 1.772030] usb 2-1: new full speed USB device using ohci_hcd and address 2
[ 1.841084] vesafb: framebuffer at 0xc0000000, mapped to 0xf8100000, using 320k, total 320k
[ 1.841088] vesafb: mode is 640x480x8, linelength=640, pages=0
[ 1.841090] vesafb: scrolling: redraw
[ 1.841093] vesafb: Pseudocolor: size=0:8:8:8, shift=0:0:0:0
[ 1.841150] fb0: VESA VGA frame buffer device
[ 1.846531] Console: switching to colour frame buffer device 80x30
[ 1.953499] usb 2-1: device descriptor read/64, error -62
[ 2.030243] xor: automatically using best checksumming function: pIII_sse
[ 2.049006] pIII_sse : 7343.000 MB/sec
[ 2.049008] xor: using function: pIII_sse (7343.000 MB/sec)
[ 2.051493] device-mapper: dm-raid45: initialized v0.2594b
[ 2.253020] usb 2-1: device descriptor read/64, error -62
[ 2.270247] PM: Starting manual resume from disk
[ 2.270252] PM: Resume from partition 8:5
[ 2.270254] PM: Checking hibernation image.
[ 2.270478] PM: Resume from disk failed.
[ 2.306346] EXT4-fs (sda1): barriers enabled
[ 2.330213] kjournald2 starting: pid 371, dev sda1:8, commit interval 5 seconds
[ 2.330291] EXT4-fs (sda1): delayed allocation enabled
[ 2.330294] EXT4-fs: file extents enabled
[ 2.337567] EXT4-fs: mballoc enabled
[ 2.337585] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 2.533032] usb 2-1: new full speed USB device using ohci_hcd and address 3
[ 2.716028] usb 2-1: device descriptor read/64, error -62
[ 3.000030] usb 2-1: device descriptor read/64, error -62
[ 3.115759] type=1505 audit(1267701631.614:2): operation="profile_load" pid=396 name=/usr/share/gdm/guest-session/Xsession
[ 3.119244] type=1505 audit(1267701631.616:3): operation="profile_load" pid=397 name=/sbin/dhclient3
[ 3.119980] type=1505 audit(1267701631.616:4): operation="profile_load" pid=397 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[ 3.120380] type=1505 audit(1267701631.620:5): operation="profile_load" pid=397 name=/usr/lib/connman/scripts/dhclient-script
[ 3.194267] type=1505 audit(1267701631.692:6): operation="profile_load" pid=398 name=/usr/bin/evince
[ 3.206417] type=1505 audit(1267701631.704:7): operation="profile_load" pid=398 name=/usr/bin/evince-previewer
[ 3.213642] type=1505 audit(1267701631.712:8): operation="profile_load" pid=398 name=/usr/bin/evince-thumbnailer
[ 3.234040] type=1505 audit(1267701631.732:9): operation="profile_load" pid=400 name=/usr/lib/cups/backend/cups-pdf
[ 3.280424] usb 2-1: new full speed USB device using ohci_hcd and address 4
[ 3.688024] usb 2-1: device not accepting address 4, error -62
[ 3.864040] usb 2-1: new full speed USB device using ohci_hcd and address 5
[ 4.272029] usb 2-1: device not accepting address 5, error -62
[ 4.272050] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 4.344732] usb 1-3.4: new low speed USB device using ehci_hcd and address 4
[ 4.445071] usb 1-3.4: configuration #1 chosen from 1 choice
[ 16.342939] udev: starting version 147
[ 16.361377] lp: driver loaded but no devices found
[ 16.387094] Adding 5277312k swap on /dev/sda5. Priority:-1 extents:1 across:5277312k
[ 16.402527] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 16.511769] EXT4-fs (sda1): internal journal on sda1:8
[ 16.533768] sis190 Gigabit Ethernet driver 1.3 loaded.
[ 16.533795] alloc irq_desc for 19 on node -1
[ 16.533797] alloc kstat_irqs on node -1
[ 16.533807] sis190 0000:00:04.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 16.533821] sis190 0000:00:04.0: setting latency timer to 64
[ 16.533844] 0000:00:04.0: Read MAC address from EEPROM
[ 16.581788] cfg80211: Calling CRDA to update world regulatory domain
[ 16.602257] ath5k 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 16.602271] ath5k 0000:02:00.0: setting latency timer to 64
[ 16.602327] ath5k 0000:02:00.0: registered as 'phy0'
[ 16.730057] usbcore: registered new interface driver hiddev
[ 16.735002] input: Microsoft Microsoft Basic Optical Mouse as /devices/pci0000:00/0000:00:03.3/usb1/1-3/1-3.4/1-3.4:1.0/input/input7
[ 16.735101] generic-usb 0003:045E:0084.0001: input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft Basic Optical Mouse] on usb-0000:00:03.3-3.4/input0
[ 16.735122] usbcore: registered new interface driver usbhid
[ 16.735125] usbhid: v2.6:USB HID core driver
[ 16.881807] cfg80211: World regulatory domain updated:
[ 16.881811] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 16.881814] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 16.881817] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 16.881820] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 16.881822] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 16.881825] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 16.951053] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.988017] 0000:00:04.0: Atheros PHY transceiver at address 1.
[ 17.118991] ath: EEPROM regdomain: 0x30
[ 17.118995] ath: EEPROM indicates we should expect a direct regpair map
[ 17.118999] ath: Country alpha2 being used: AM
[ 17.119001] ath: Regpair used: 0x30
[ 17.146204] phy0: Selected rate control algorithm 'minstrel'
[ 17.146893] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
[ 17.147770] cfg80211: Calling CRDA for country: AM
[ 17.171568] cfg80211: Regulatory domain changed to country: AM
[ 17.171573] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 17.171575] (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 17.171578] (5170000 KHz - 5250000 KHz @ 20000 KHz), (N/A, 1800 mBm)
[ 17.171580] (5250000 KHz - 5330000 KHz @ 20000 KHz), (N/A, 1800 mBm)
[ 17.305985] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1a0b1, caps: 0xa04753/0x200000
[ 17.342157] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8
[ 17.365336] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 17.380605] __ratelimit: 9 callbacks suppressed
[ 17.380610] type=1505 audit(1267701645.880:13): operation="profile_replace" pid=953 name=/usr/share/gdm/guest-session/Xsession
[ 17.382924] type=1505 audit(1267701645.880:14): operation="profile_replace" pid=954 name=/sbin/dhclient3
[ 17.383664] type=1505 audit(1267701645.880:15): operation="profile_replace" pid=954 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[ 17.384093] type=1505 audit(1267701645.884:16): operation="profile_replace" pid=954 name=/usr/lib/connman/scripts/dhclient-script
[ 17.394834] type=1505 audit(1267701645.892:17): operation="profile_replace" pid=955 name=/usr/bin/evince
[ 17.406913] type=1505 audit(1267701645.904:18): operation="profile_replace" pid=955 name=/usr/bin/evince-previewer
[ 17.414348] type=1505 audit(1267701645.912:19): operation="profile_replace" pid=955 name=/usr/bin/evince-thumbnailer
[ 17.429452] type=1505 audit(1267701645.928:20): operation="profile_replace" pid=959 name=/usr/lib/cups/backend/cups-pdf
[ 17.430314] type=1505 audit(1267701645.928:21): operation="profile_replace" pid=959 name=/usr/sbin/cupsd
[ 17.436404] type=1505 audit(1267701645.936:22): operation="profile_replace" pid=964 name=/usr/sbin/mysqld-akonadi
[ 17.570521] 0000:00:04.0: Using transceiver at address 1 as default.
[ 17.606100] 0000:00:04.0: SiS 191 PCI Gigabit Ethernet adapter at f86fa000 (IRQ: 19), 00:1e:33:06:6a:c9
[ 17.606104] eth0: RGMII mode.
[ 17.606108] eth0: Enabling Auto-negotiation.
[ 17.665250] alloc irq_desc for 18 on node -1
[ 17.665255] alloc kstat_irqs on node -1
[ 17.665264] HDA Intel 0000:00:0f.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 17.665332] HDA Intel 0000:00:0f.0: setting latency timer to 64
[ 17.670319] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 17.746956] hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
[ 17.747052] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:0f.0/input/input9
[ 19.778325] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 19.778329] vboxdrv: Warning: 2.6.31+ kernel detected. Most likely the hardware performance
[ 19.778331] vboxdrv: counter framework which can generate NMIs is active. You have to prevent
[ 19.778332] vboxdrv: the usage of hardware performance counters by
[ 19.778333] vboxdrv: echo 2 > /proc/sys/kernel/perf_counter_paranoid
[ 19.778338] vboxdrv: Found 2 processor cores.
[ 19.778432] vboxdrv: fAsync=0 offMin=0x1a4 offMax=0x21b1
[ 19.778492] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 19.778494] vboxdrv: Successfully loaded version 3.1.4 (interface 0x00100001).
[ 20.219977] ppdev: user-space parallel port driver
[ 20.700072] usb 2-1: new full speed USB device using ohci_hcd and address 6
[ 20.876043] usb 2-1: device descriptor read/64, error -62
[ 21.164032] usb 2-1: device descriptor read/64, error -62
[ 21.444019] usb 2-1: new full speed USB device using ohci_hcd and address 7
[ 21.641427] usb 2-1: device descriptor read/64, error -62
[ 21.642554] [drm] Initialized drm 1.1.0 20060810
[ 21.644594] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 21.644601] pci 0000:01:00.0: setting latency timer to 64
[ 21.645199] [drm] Initialized sis 1.3.0 20070626 for 0000:01:00.0 on minor 0
[ 21.647813] agpgart-sis 0000:00:00.0: AGP 3.5 bridge
[ 21.647844] agpgart-sis 0000:00:00.0: putting AGP V3 device into 4x mode
[ 21.647940] pci 0000:01:00.0: putting AGP V3 device into 4x mode
[ 21.932043] usb 2-1: device descriptor read/64, error -62
[ 22.080189] sr 2:0:0:0: [sr0] Unhandled sense code
[ 22.080193] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 22.080198] sr 2:0:0:0: [sr0] Sense Key : Blank Check [current]
[ 22.080204] Info fld=0x0
[ 22.080205] sr 2:0:0:0: [sr0] <<vendor>> ASC=0xab ASCQ=0x80ASC=0xab <<vendor>> ASCQ=0x80
[ 22.080213] end_request: I/O error, dev sr0, sector 0
[ 22.216039] usb 2-1: new full speed USB device using ohci_hcd and address 8
[ 22.660028] usb 2-1: device not accepting address 8, error -62
[ 22.840037] usb 2-1: new full speed USB device using ohci_hcd and address 9
[ 22.896030] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
[ 23.252029] usb 2-1: device not accepting address 9, error -62
[ 23.252053] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 23.272340] sr 2:0:0:0: [sr0] Unhandled sense code
[ 23.272345] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 23.272349] sr 2:0:0:0: [sr0] Sense Key : Blank Check [current]
[ 23.272355] Info fld=0x0
[ 23.272356] sr 2:0:0:0: [sr0] <<vendor>> ASC=0xab ASCQ=0x80ASC=0xab <<vendor>> ASCQ=0x80
[ 23.272364] end_request: I/O error, dev sr0, sector 0
[ 23.272370] __ratelimit: 4 callbacks suppressed
[ 23.272372] Buffer I/O error on device sr0, logical block 0
[ 23.290947] cdrom: This disc doesn't have any tracks I recognize!
[ 25.796189] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 25.796196] sr 2:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 25.796203] Info fld=0x0
[ 25.796205] sr 2:0:0:0: [sr0] Add. Sense: Logical block address out of range
[ 25.796211] end_request: I/O error, dev sr0, sector 0
[ 25.796218] Buffer I/O error on device sr0, logical block 0
[ 25.812064] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 25.812072] sr 2:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 25.812078] Info fld=0x0
[ 25.812080] sr 2:0:0:0: [sr0] Add. Sense: Logical block address out of range
[ 25.812087] end_request: I/O error, dev sr0, sector 0
[ 25.812094] Buffer I/O error on device sr0, logical block 0
[ 27.692055] eth0: auto-negotiating...
[ 37.716033] eth0: auto-negotiating...
[ 47.740020] eth0: auto-negotiating...
[ 57.764021] eth0: auto-negotiating...
[ 67.796038] eth0: auto-negotiating...
[ 77.820022] eth0: auto-negotiating...
[ 87.844031] eth0: auto-negotiating...
[ 97.868035] eth0: auto-negotiating...
[ 107.896080] eth0: auto-negotiating...
[ 117.944045] eth0: auto-negotiating...
[ 127.968044] eth0: auto-negotiating...
[ 137.992034] eth0: auto-negotiating...
[ 142.249955] wlan0: authenticate with AP 00:05:59:1c:c6:5d
[ 142.251334] wlan0: authenticated
[ 142.251337] wlan0: associate with AP 00:05:59:1c:c6:5d
[ 142.272282] wlan0: RX AssocResp from 00:05:59:1c:c6:5d (capab=0x431 status=0 aid=1)
[ 142.272290] wlan0: associated
[ 142.273644] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 142.728918] padlock: VIA PadLock not detected.
[ 148.016033] eth0: auto-negotiating...
[ 152.592030] wlan0: no IPv6 routers present
[ 153.644320] usb 1-3.3: new high speed USB device using ehci_hcd and address 5
[ 153.869774] usb 1-3.3: configuration #1 chosen from 1 choice
[ 154.041480] Linux video capture interface: v2.00
[ 154.561758] usbcore: registered new interface driver snd-usb-audio
[ 154.562090] uvcvideo: Found UVC 1.00 device Trust 2MP Auto Focus we (145f:0348)
[ 154.647253] input: Trust 2MP Auto Focus we as /devices/pci0000:00/0000:00:03.3/usb1/1-3/1-3.3/1-3.3:1.0/input/input10
[ 154.647383] usbcore: registered new interface driver uvcvideo
[ 154.647390] USB Video Class driver (v0.1.0)
[ 155.692055] usb 1-2: new high speed USB device using ehci_hcd and address 6
[ 155.824620] usb 1-2: configuration #1 chosen from 1 choice
[ 155.933617] em28xx: New device @ 480 Mbps (eb1a:2820, interface 0, class 0)
[ 155.933860] em28xx #0: chip ID is em2820 (or em2710)
[ 156.061299] em28xx #0: i2c eeprom 00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 156.061330] em28xx #0: i2c eeprom 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 156.061359] em28xx #0: i2c eeprom 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 156.061387] em28xx #0: i2c eeprom 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 156.061415] em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 156.061442] em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 156.061470] em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 156.061498] em28xx #0: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 156.061526] em28xx #0: i2c eeprom 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 156.061554] em28xx #0: i2c eeprom 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 156.061582] em28xx #0: i2c eeprom a0: 00 00 45 24 00 00 00 00 00 00 00 00 00 00 00 00
[ 156.061610] em28xx #0: i2c eeprom b0: 00 00 00 00 31 30 4d 4f 4f 4e 53 32 38 32 30 00
[ 156.061638] em28xx #0: i2c eeprom c0: 41 45 00 00 ff ff ff ff ff ff ff ff ff ff ff ff
[ 156.061666] em28xx #0: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 156.061694] em28xx #0: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 156.061722] em28xx #0: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 156.061751] em28xx #0: EEPROM ID= 0x00000000, EEPROM hash = 0x00000000
[ 156.061756] em28xx #0: EEPROM info:
[ 156.061759] em28xx #0: No audio on board.
[ 156.061763] em28xx #0: 500mA max power
[ 156.061769] em28xx #0: Table at 0x00, strings=0x0000, 0x0000, 0x0000
[ 156.072628] Unknown Micron Sensor 0x00ff
[ 156.072637] em28xx #0: Identified as Unknown EM2750/28xx video grabber (card=1)
[ 156.087785] em28xx #0: found i2c device @ 0x4a [saa7113h]
[ 156.104278] em28xx #0: found i2c device @ 0xa0 [eeprom]
[ 156.109149] em28xx #0: found i2c device @ 0xba [webcam sensor or tvp5150a]
[ 156.110642] em28xx #0: found i2c device @ 0xc2 [tuner (analog)]
[ 156.111391] em28xx #0: found i2c device @ 0xc6 [tuner (analog)]
[ 156.122770] em28xx #0: Your board has no unique USB ID and thus need a hint to be detected.
[ 156.122779] em28xx #0: You may try to use card=<n> insmod option to workaround that.
[ 156.122784] em28xx #0: Please send an email with this log to:
[ 156.122789] em28xx #0: V4L Mailing List <linux-media@vger.kernel.org>
[ 156.122794] em28xx #0: Board eeprom hash is 0x00000000
[ 156.122800] em28xx #0: Board i2c devicelist hash is 0x150600e3
[ 156.122804] em28xx #0: Here is a list of valid choices for the card=<n> insmod option:
[ 156.122812] em28xx #0: card=0 -> Unknown EM2800 video grabber
[ 156.122818] em28xx #0: card=1 -> Unknown EM2750/28xx video grabber
[ 156.122823] em28xx #0: card=2 -> Terratec Cinergy 250 USB
[ 156.122829] em28xx #0: card=3 -> Pinnacle PCTV USB 2
[ 156.122835] em28xx #0: card=4 -> Hauppauge WinTV USB 2
[ 156.122841] em28xx #0: card=5 -> MSI VOX USB 2.0
[ 156.122846] em28xx #0: card=6 -> Terratec Cinergy 200 USB
[ 156.122852] em28xx #0: card=7 -> Leadtek Winfast USB II
[ 156.122858] em28xx #0: card=8 -> Kworld USB2800
[ 156.122864] em28xx #0: card=9 -> Pinnacle Dazzle DVC 90/100/101/107 / Kaiser Baas Video to DVD maker
[ 156.122870] em28xx #0: card=10 -> Hauppauge WinTV HVR 900
[ 156.122876] em28xx #0: card=11 -> Terratec Hybrid XS
[ 156.122881] em28xx #0: card=12 -> Kworld PVR TV 2800 RF
[ 156.122887] em28xx #0: card=13 -> Terratec Prodigy XS
[ 156.122893] em28xx #0: card=14 -> SIIG AVTuner-PVR / Pixelview Prolink PlayTV USB 2.0
[ 156.122899] em28xx #0: card=15 -> V-Gear PocketTV
[ 156.122905] em28xx #0: card=16 -> Hauppauge WinTV HVR 950
[ 156.122911] em28xx #0: card=17 -> Pinnacle PCTV HD Pro Stick
[ 156.122917] em28xx #0: card=18 -> Hauppauge WinTV HVR 900 (R2)
[ 156.122923] em28xx #0: card=19 -> EM2860/SAA711X Reference Design
[ 156.122929] em28xx #0: card=20 -> AMD ATI TV Wonder HD 600
[ 156.122935] em28xx #0: card=21 -> eMPIA Technology, Inc. GrabBeeX+ Video Encoder
[ 156.122942] em28xx #0: card=22 -> EM2710/EM2750/EM2751 webcam grabber
[ 156.122948] em28xx #0: card=23 -> Huaqi DLCW-130
[ 156.122954] em28xx #0: card=24 -> D-Link DUB-T210 TV Tuner
[ 156.122959] em28xx #0: card=25 -> Gadmei UTV310
[ 156.122965] em28xx #0: card=26 -> Hercules Smart TV USB 2.0
[ 156.122971] em28xx #0: card=27 -> Pinnacle PCTV USB 2 (Philips FM1216ME)
[ 156.122977] em28xx #0: card=28 -> Leadtek Winfast USB II Deluxe
[ 156.122983] em28xx #0: card=29 -> <NULL>
[ 156.122989] em28xx #0: card=30 -> Videology 20K14XUSB USB2.0
[ 156.122995] em28xx #0: card=31 -> Usbgear VD204v9
[ 156.123000] em28xx #0: card=32 -> Supercomp USB 2.0 TV
[ 156.123006] em28xx #0: card=33 -> <NULL>
[ 156.123012] em28xx #0: card=34 -> Terratec Cinergy A Hybrid XS
[ 156.123018] em28xx #0: card=35 -> Typhoon DVD Maker
[ 156.123023] em28xx #0: card=36 -> NetGMBH Cam
[ 156.123029] em28xx #0: card=37 -> Gadmei UTV330
[ 156.123034] em28xx #0: card=38 -> Yakumo MovieMixer
[ 156.123040] em28xx #0: card=39 -> KWorld PVRTV 300U
[ 156.123045] em28xx #0: card=40 -> Plextor ConvertX PX-TV100U
[ 156.123051] em28xx #0: card=41 -> Kworld 350 U DVB-T
[ 156.123057] em28xx #0: card=42 -> Kworld 355 U DVB-T
[ 156.123062] em28xx #0: card=43 -> Terratec Cinergy T XS
[ 156.123068] em28xx #0: card=44 -> Terratec Cinergy T XS (MT2060)
[ 156.123074] em28xx #0: card=45 -> Pinnacle PCTV DVB-T
[ 156.123080] em28xx #0: card=46 -> Compro, VideoMate U3
[ 156.123086] em28xx #0: card=47 -> KWorld DVB-T 305U
[ 156.123092] em28xx #0: card=48 -> KWorld DVB-T 310U
[ 156.123097] em28xx #0: card=49 -> MSI DigiVox A/D
[ 156.123103] em28xx #0: card=50 -> MSI DigiVox A/D II
[ 156.123109] em28xx #0: card=51 -> Terratec Hybrid XS Secam
[ 156.123114] em28xx #0: card=52 -> DNT DA2 Hybrid
[ 156.123132] em28xx #0: card=53 -> Pinnacle Hybrid Pro
[ 156.123137] em28xx #0: card=54 -> Kworld VS-DVB-T 323UR
[ 156.123143] em28xx #0: card=55 -> Terratec Hybrid XS (em2882)
[ 156.123149] em28xx #0: card=56 -> Pinnacle Hybrid Pro (2)
[ 156.123155] em28xx #0: card=57 -> Kworld PlusTV HD Hybrid 330
[ 156.123161] em28xx #0: card=58 -> Compro VideoMate ForYou/Stereo
[ 156.123167] em28xx #0: card=59 -> <NULL>
[ 156.123172] em28xx #0: card=60 -> Hauppauge WinTV HVR 850
[ 156.123178] em28xx #0: card=61 -> Pixelview PlayTV Box 4 USB 2.0
[ 156.123183] em28xx #0: card=62 -> Gadmei TVR200
[ 156.123189] em28xx #0: card=63 -> Kaiomy TVnPC U2
[ 156.123195] em28xx #0: card=64 -> Easy Cap Capture DC-60
[ 156.123201] em28xx #0: card=65 -> IO-DATA GV-MVP/SZ
[ 156.123206] em28xx #0: card=66 -> Empire dual TV
[ 156.123212] em28xx #0: card=67 -> Terratec Grabby
[ 156.123217] em28xx #0: card=68 -> Terratec AV350
[ 156.123223] em28xx #0: card=69 -> KWorld ATSC 315U HDTV TV Box
[ 156.123229] em28xx #0: card=70 -> Evga inDtube
[ 156.123235] em28xx #0: card=71 -> Silvercrest Webcam 1.3mpix
[ 156.123387] em28xx #0: Config register raw data: 0x00
[ 156.123394] em28xx #0: v4l2 driver version 0.1.2
[ 156.528243] em28xx #0: V4L2 device registered as /dev/video1 and /dev/vbi0
[ 156.528299] usbcore: registered new interface driver em28xx
[ 156.528306] em28xx driver loaded
[ 158.040040] eth0: auto-negotiating...
[ 168.064038] eth0: auto-negotiating...
[ 178.088054] eth0: auto-negotiating...
[ 188.132070] eth0: auto-negotiating...
[ 198.156053] eth0: auto-negotiating...
[ 208.180037] eth0: auto-negotiating...
[ 218.204432] eth0: auto-negotiating...
[ 228.228060] eth0: auto-negotiating...
[ 238.252017] eth0: auto-negotiating...
[ 248.276054] eth0: auto-negotiating...
[ 258.300040] eth0: auto-negotiating...
[ 268.324033] eth0: auto-negotiating...
[ 278.348041] eth0: auto-negotiating...


to tvtime τωρα γραφει frames too short from uvcvideo.....