καρτα tv gigabyte u8000

...hardware-drivers για περιφερειακά (εκτυπωτές, κάμερες, εξ. σκληροί, κλπ)
Κανόνες Δ. Συζήτησης
Για την ευκολότερη επίλυση του προβλήματός σας.
Καλό είναι να δημοσιεύσετε τα αποτελέσματα της εντολής στο τερματικό :
lsusb

καρτα tv gigabyte u8000

Δημοσίευσηαπό LEONDAS » 28 Ιαν 2009, 21:37

Το προβλημα ειναι με καρτα tv την οποια προσπαθησε και καποιος αλλος να κανει να δουλεψει εδω http://forum.ubuntu-gr.org/viewtopic.php?f=24&t=1799&hilit=GIGABYTE.Τα δοκιμασα αλλα τιποτα ή μαλλον αναψε στην αρχη το λαμπακι της καρτας.Καμμια ιδεα κανεις?
Ubuntu 8.10 32bit σε Core2Duo Turbox (Mitac 8227d barebone)
Αγγλικα καλα/γνωσεις προγραμματισμου λιγες/γνωσεις χειρισμου linux μετρια
T7250 2GHz/2GB/GeForce 8600M GS/HDA-Intel 82801H/1440x900/Intel Corporation PRO/4965 AG or AGN [Kedron] Network Connection
LEONDAS
babeTUX
babeTUX
 
Δημοσιεύσεις: 30
Εγγραφή: 21 Ιαν 2009, 14:02
Τοποθεσία: Βολος
Εκτύπωση

Re: καρτα tv gigabyte u8000

Δημοσίευσηαπό logari81 » 28 Ιαν 2009, 22:17

ανεβασε το αποτελεσμα των
Κώδικας: Επιλογή όλων
lspci -nn
lsmod |grep dvb
dmesg

και κανε μια περιληψη τι εχεις δοκιμασει για να μην χρειαζεται να ξαναδιαβαζουμε ολο το νημα που ανεφερες.
http://opensourceecology.org/


Λειτουργικό: Ubuntu 10.04 lucid 64-bitΠροδιαγραφές: 4x Intel Core i5 CPU M 450 2.40GHz ‖ RAM 3696 MiB ‖ Lenovo KL3 - LENOVO IdeaPad Y560
Κάρτα γραφικών: ATI Device [1002:68c0]Ασύρματο: wlan0: Atheros Inc. AR928X Wireless Network Adapter (PCI-Express) [168c:002a] (rev 01)
logari81
Επίτιμο μέλος
Επίτιμο μέλος
 
Δημοσιεύσεις: 6074
Εγγραφή: 14 Μάιος 2008, 10:40
Εκτύπωση

Re: καρτα tv gigabyte u8000

Δημοσίευσηαπό LEONDAS » 28 Ιαν 2009, 22:23

logari81 έγραψε:ανεβασε το αποτελεσμα των
Κώδικας: Επιλογή όλων
lspci -nn
lsmod |grep dvb
dmesg

και κανε μια περιληψη τι εχεις δοκιμασει για να μην χρειαζεται να ξαναδιαβαζουμε ολο το νημα που ανεφερες.


Κώδικας: Επιλογή όλων
[ 0.903362] bus: 06 index 1 mmio: [fa000000, fbffffff]
[ 0.903364] bus: 06 index 2 mmio: [f4000000, f5ffffff]
[ 0.903366] bus: 06 index 3 mmio: [0, 0]
[ 0.903368] bus: 08 index 0 mmio: [0, 0]
[ 0.903370] bus: 08 index 1 mmio: [0, 0]
[ 0.903372] bus: 08 index 2 mmio: [0, 0]
[ 0.903374] bus: 08 index 3 io port: [0, ffff]
[ 0.903376] bus: 08 index 4 mmio: [0, ffffffff]
[ 0.903383] NET: Registered protocol family 2
[ 0.916048] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.916274] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.916627] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.916817] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.916820] TCP reno registered
[ 0.920069] NET: Registered protocol family 1
[ 0.920182] checking if image is initramfs... it is
[ 1.605778] Freeing initrd memory: 8012k freed
[ 1.606104] Simple Boot Flag at 0x36 set to 0x1
[ 1.606829] audit: initializing netlink socket (disabled)
[ 1.606852] type=2000 audit(1233166714.604:1): initialized
[ 1.612779] highmem bounce pool size: 64 pages
[ 1.612785] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.614965] VFS: Disk quotas dquot_6.5.1
[ 1.615048] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.615144] msgmni has been set to 1743
[ 1.615258] io scheduler noop registered
[ 1.615260] io scheduler anticipatory registered
[ 1.615263] io scheduler deadline registered
[ 1.615274] io scheduler cfq registered (default)
[ 1.615461] pci 0000:01:00.0: Boot video device
[ 1.615567] pcieport-driver 0000:00:01.0: setting latency timer to 64
[ 1.615606] pcieport-driver 0000:00:01.0: found MSI capability
[ 1.615638] pci_express 0000:00:01.0:pcie00: allocate port service
[ 1.615677] pci_express 0000:00:01.0:pcie02: allocate port service
[ 1.615714] pci_express 0000:00:01.0:pcie03: allocate port service
[ 1.615804] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 1.615855] pcieport-driver 0000:00:1c.0: found MSI capability
[ 1.615906] pci_express 0000:00:1c.0:pcie00: allocate port service
[ 1.615943] pci_express 0000:00:1c.0:pcie02: allocate port service
[ 1.615980] pci_express 0000:00:1c.0:pcie03: allocate port service
[ 1.616095] pcieport-driver 0000:00:1c.2: setting latency timer to 64
[ 1.616146] pcieport-driver 0000:00:1c.2: found MSI capability
[ 1.616196] pci_express 0000:00:1c.2:pcie00: allocate port service
[ 1.616239] pci_express 0000:00:1c.2:pcie02: allocate port service
[ 1.616277] pci_express 0000:00:1c.2:pcie03: allocate port service
[ 1.616387] pcieport-driver 0000:00:1c.3: setting latency timer to 64
[ 1.616439] pcieport-driver 0000:00:1c.3: found MSI capability
[ 1.616489] pci_express 0000:00:1c.3:pcie00: allocate port service
[ 1.616527] pci_express 0000:00:1c.3:pcie02: allocate port service
[ 1.616564] pci_express 0000:00:1c.3:pcie03: allocate port service
[ 1.616890] isapnp: Scanning for PnP cards...
[ 1.971876] isapnp: No Plug & Play device found
[ 2.002158] hpet_resources: 0xfed00000 is busy
[ 2.002224] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 2.004268] brd: module loaded
[ 2.004334] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 2.004447] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.007091] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 2.008153] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.008158] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 2.008161] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 2.008163] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 2.008166] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 2.008461] mice: PS/2 mouse device common for all mice
[ 2.008579] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 2.008610] rtc0: alarms up to one month, y3k, hpet irqs
[ 2.008723] EISA: Probing bus 0 at eisa.0
[ 2.008730] Cannot allocate resource for EISA slot 1
[ 2.008734] Cannot allocate resource for EISA slot 2
[ 2.008736] Cannot allocate resource for EISA slot 3
[ 2.008738] Cannot allocate resource for EISA slot 4
[ 2.008740] Cannot allocate resource for EISA slot 5
[ 2.008755] EISA: Detected 0 cards.
[ 2.008758] cpuidle: using governor ladder
[ 2.008761] cpuidle: using governor menu
[ 2.009261] TCP cubic registered
[ 2.009287] Using IPI No-Shortcut mode
[ 2.009445] registered taskstats version 1
[ 2.009562] Magic number: 9:254:343
[ 2.009613] tty tty60: hash matches
[ 2.009666] rtc_cmos 00:07: setting system clock to 2009-01-28 18:18:35 UTC (1233166715)
[ 2.009669] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.009671] EDD information not available.
[ 2.009898] Freeing unused kernel memory: 424k freed
[ 2.009935] Write protecting the kernel text: 2580k
[ 2.009963] Write protecting the kernel read-only data: 940k
[ 2.049419] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 2.156181] fuse init (API version 7.9)
[ 2.184800] ACPI: SSDT 7FED642B, 027A (r1 PmRef Cpu0Ist 3000 INTL 20050624)
[ 2.185194] ACPI: SSDT 7FED5EFC, 04AA (r1 PmRef Cpu0Cst 3001 INTL 20050624)
[ 2.248337] Monitor-Mwait will be used to enter C-1 state
[ 2.248341] Monitor-Mwait will be used to enter C-2 state
[ 2.248344] Monitor-Mwait will be used to enter C-3 state
[ 2.272134] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 2.272192] processor ACPI0007:00: registered as cooling_device0
[ 2.272196] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 2.272560] ACPI: SSDT 7FED66A5, 00C8 (r1 PmRef Cpu1Ist 3000 INTL 20050624)
[ 2.272913] ACPI: SSDT 7FED63A6, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050624)
[ 2.274021] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 2.274069] processor ACPI0007:01: registered as cooling_device1
[ 2.274073] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 2.276499] Marking TSC unstable due to TSC halts in idle
[ 2.276992] thermal LNXTHERM:01: registered as thermal_zone0
[ 2.278299] ACPI: Thermal Zone [TZ00] (71 C)
[ 2.278697] thermal LNXTHERM:02: registered as thermal_zone1
[ 2.278850] ACPI: Thermal Zone [TZ01] (72 C)
[ 2.656076] usbcore: registered new interface driver usbfs
[ 2.656099] usbcore: registered new interface driver hub
[ 2.667998] usbcore: registered new device driver usb
[ 2.676010] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.676032] r8169 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 2.676054] r8169 0000:04:00.0: setting latency timer to 64
[ 2.676478] eth0: RTL8101e at 0xf884a000, 00:40:d0:d2:2b:d2, XID 34200000 IRQ 219
[ 2.692102] USB Universal Host Controller Interface driver v3.0
[ 2.692155] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.692164] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 2.692169] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 2.692219] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 2.692257] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800
[ 2.692419] usb usb1: configuration #1 chosen from 1 choice
[ 2.692469] hub 1-0:1.0: USB hub found
[ 2.692476] hub 1-0:1.0: 2 ports detected
[ 2.744100] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 2.768189] No dock devices found.
[ 2.789641] SCSI subsystem initialized
[ 2.806179] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 2.806189] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 2.806194] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 2.806218] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 2.806256] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820
[ 2.806350] usb usb2: configuration #1 chosen from 1 choice
[ 2.806377] hub 2-0:1.0: USB hub found
[ 2.806383] hub 2-0:1.0: 2 ports detected
[ 2.829190] libata version 3.00 loaded.
[ 2.908372] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.908390] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 2.908394] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 2.908427] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3
[ 2.912323] ehci_hcd 0000:00:1a.7: debug port 1
[ 2.912330] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 2.912344] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfc204800
[ 2.929074] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.929224] usb usb3: configuration #1 chosen from 1 choice
[ 2.929252] hub 3-0:1.0: USB hub found
[ 2.929261] hub 3-0:1.0: 4 ports detected
[ 3.197565] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 3.197575] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 3.197579] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 3.197609] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 3.197647] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840
[ 3.197741] usb usb4: configuration #1 chosen from 1 choice
[ 3.197765] hub 4-0:1.0: USB hub found
[ 3.197771] hub 4-0:1.0: 2 ports detected
[ 3.369049] usb 3-4: new high speed USB device using ehci_hcd and address 2
[ 3.404171] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 3.404179] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 3.404183] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 3.404206] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
[ 3.404244] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001860
[ 3.404334] usb usb5: configuration #1 chosen from 1 choice
[ 3.404359] hub 5-0:1.0: USB hub found
[ 3.404365] hub 5-0:1.0: 2 ports detected
[ 3.500055] Clocksource tsc unstable (delta = -202046469 ns)
[ 3.508310] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 3.508320] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 3.508324] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.508350] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
[ 3.508381] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001880
[ 3.508479] usb usb6: configuration #1 chosen from 1 choice
[ 3.508503] hub 6-0:1.0: USB hub found
[ 3.508509] hub 6-0:1.0: 2 ports detected
[ 3.517139] usb 3-4: configuration #1 chosen from 1 choice
[ 3.716674] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 3.716689] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 3.716693] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 3.716721] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
[ 3.720627] ehci_hcd 0000:00:1d.7: debug port 1
[ 3.720634] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 3.720640] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfc204c00
[ 3.732082] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 3.732373] usb usb7: configuration #1 chosen from 1 choice
[ 3.732579] hub 7-0:1.0: USB hub found
[ 3.732586] hub 7-0:1.0: 6 ports detected
[ 3.941957] ata_piix 0000:00:1f.1: version 2.12
[ 3.941969] ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 3.942011] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 3.942085] scsi0 : ata_piix
[ 3.942189] scsi1 : ata_piix
[ 3.942876] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18a0 irq 14
[ 3.942879] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18a8 irq 15
[ 4.104504] ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-T20N, WA03, max UDMA/33
[ 4.120487] ata1.00: configured for UDMA/33
[ 4.290966] scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T20N WA03 PQ: 0 ANSI: 5
[ 4.292164] ahci 0000:00:1f.2: version 3.0
[ 4.292180] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 4.292297] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
[ 4.292300] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part
[ 4.292306] ahci 0000:00:1f.2: setting latency timer to 64
[ 4.292507] scsi2 : ahci
[ 4.292598] scsi3 : ahci
[ 4.292672] scsi4 : ahci
[ 4.292782] ata3: SATA max UDMA/133 abar m2048@0xfc204000 port 0xfc204100 irq 218
[ 4.292786] ata4: SATA max UDMA/133 abar m2048@0xfc204000 port 0xfc204180 irq 218
[ 4.292790] ata5: SATA max UDMA/133 abar m2048@0xfc204000 port 0xfc204200 irq 218
[ 4.612105] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.612788] ata3.00: _GTF unexpected object type 0x1
[ 4.667915] ata3.00: ATA-7: WDC WD1600BEVS-00RST0, 04.01G04, max UDMA/133
[ 4.667918] ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 4.668890] ata3.00: _GTF unexpected object type 0x1
[ 4.669075] ata3.00: configured for UDMA/133
[ 4.752076] usb 7-1: new high speed USB device using ehci_hcd and address 2
[ 4.885811] usb 7-1: configuration #1 chosen from 1 choice
[ 5.004615] ata4: SATA link down (SStatus 0 SControl 300)
[ 5.108085] usb 7-3: new high speed USB device using ehci_hcd and address 4
[ 5.241660] usb 7-3: configuration #1 chosen from 1 choice
[ 5.340097] ata5: SATA link down (SStatus 0 SControl 300)
[ 5.352084] usb 7-4: new high speed USB device using ehci_hcd and address 5
[ 5.356160] scsi 2:0:0:0: Direct-Access ATA WDC WD1600BEVS-0 04.0 PQ: 0 ANSI: 5
[ 5.368443] scsi 0:0:0:0: Attached scsi generic sg0 type 5
[ 5.368480] scsi 2:0:0:0: Attached scsi generic sg1 type 0
[ 5.388698] Driver 'sd' needs updating - please use bus_type methods
[ 5.388806] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 5.388821] sd 2:0:0:0: [sda] Write Protect is off
[ 5.388824] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.388849] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.388910] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 5.388924] sd 2:0:0:0: [sda] Write Protect is off
[ 5.388926] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.388950] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.388953] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 5.403778] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.403782] Uniform CD-ROM driver Revision: 3.20
[ 5.403864] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 5.439821] sda1 sda2 sda3 < sda5 >
[ 5.463822] sd 2:0:0:0: [sda] Attached SCSI disk
[ 5.487554] usb 7-4: configuration #1 chosen from 1 choice
[ 5.597066] usb 7-5: new high speed USB device using ehci_hcd and address 6
[ 5.748096] usb 7-5: configuration #1 chosen from 1 choice
[ 5.860264] usbcore: registered new interface driver libusual
[ 5.866404] Initializing USB Mass Storage driver...
[ 5.900282] PM: Starting manual resume from disk
[ 5.900285] PM: Resume from partition 8:5
[ 5.900287] PM: Checking hibernation image.
[ 5.900476] PM: Resume from disk failed.
[ 5.953783] kjournald starting. Commit interval 5 seconds
[ 5.953815] EXT3-fs: mounted filesystem with ordered data mode.
[ 6.100085] usb 4-2: new full speed USB device using uhci_hcd and address 2
[ 6.265847] usb 4-2: configuration #1 chosen from 1 choice
[ 6.267755] hub 4-2:1.0: USB hub found
[ 6.269728] hub 4-2:1.0: 4 ports detected
[ 6.484746] scsi5 : SCSI emulation for USB Mass Storage devices
[ 6.484853] usb-storage: device found at 2
[ 6.484855] usb-storage: waiting for device to settle before scanning
[ 6.724054] usb 6-2: new full speed USB device using uhci_hcd and address 2
[ 6.912571] usb 6-2: configuration #1 chosen from 1 choice
[ 6.915919] scsi6 : SCSI emulation for USB Mass Storage devices
[ 6.916071] usb-storage: device found at 4
[ 6.916073] usb-storage: waiting for device to settle before scanning
[ 6.916094] scsi7 : SCSI emulation for USB Mass Storage devices
[ 6.916160] usb-storage: device found at 5
[ 6.916162] usb-storage: waiting for device to settle before scanning
[ 6.989726] usb 4-2.1: new low speed USB device using uhci_hcd and address 3
[ 7.106840] usb 4-2.1: configuration #1 chosen from 1 choice
[ 7.185725] usb 4-2.2: new low speed USB device using uhci_hcd and address 4
[ 7.323820] usb 4-2.2: configuration #1 chosen from 1 choice
[ 7.405724] usb 4-2.4: new full speed USB device using uhci_hcd and address 5
[ 7.538780] usb 4-2.4: configuration #1 chosen from 1 choice
[ 7.542792] usbcore: registered new interface driver usb-storage
[ 7.542795] USB Mass Storage support registered.
[ 11.484267] usb-storage: device scan complete
[ 11.490191] scsi 5:0:0:0: Direct-Access Generic- SD/MMC/MS/MSPro 1.00 PQ: 0 ANSI: 0 CCS
[ 11.491377] sd 5:0:0:0: [sdb] Attached SCSI removable disk
[ 11.491476] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 11.916265] usb-storage: device scan complete
[ 11.916327] usb-storage: device scan complete
[ 11.928373] scsi 7:0:0:0: Direct-Access Multi Flash Reader 1.00 PQ: 0 ANSI: 0
[ 11.928595] scsi 6:0:0:0: Direct-Access Generic External 2.02 PQ: 0 ANSI: 4
[ 11.929521] sd 6:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
[ 11.930383] sd 6:0:0:0: [sdc] Write Protect is off
[ 11.930386] sd 6:0:0:0: [sdc] Mode Sense: 21 00 00 00
[ 11.930389] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 11.931238] sd 6:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
[ 11.932115] sd 6:0:0:0: [sdc] Write Protect is off
[ 11.932118] sd 6:0:0:0: [sdc] Mode Sense: 21 00 00 00
[ 11.932120] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 11.932124] sdc: sdc1
[ 11.932873] sd 6:0:0:0: [sdc] Attached SCSI disk
[ 11.932953] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 11.933827] sd 7:0:0:0: [sdd] Attached SCSI removable disk
[ 11.933875] sd 7:0:0:0: Attached scsi generic sg4 type 0
[ 13.698940] udevd version 124 started
[ 14.064861] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 14.104195] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 14.148144] Linux agpgart interface v0.103
[ 14.254419] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 14.272026] ACPI: Power Button (FF) [PWRF]
[ 14.272161] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
[ 14.304033] ACPI: Power Button (CM) [PWRB]
[ 14.304117] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input4
[ 14.320080] ACPI: Lid Switch [LID0]
[ 14.320215] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5
[ 14.352030] ACPI: Sleep Button (CM) [SLPB]
[ 14.720241] ACPI: Battery Slot [BAT0] (battery present)
[ 14.724167] acpi device:05: registered as cooling_device2
[ 14.724355] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/device:03/input/input6
[ 14.744028] ACPI: Video Device [VGA0] (multi-head: yes rom: no post: no)
[ 14.841145] ACPI: AC Adapter [AC] (on-line)
[ 14.896321] nvidia: module license 'NVIDIA' taints kernel.
[ 15.235872] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 15.235890] nvidia 0000:01:00.0: setting latency timer to 64
[ 15.236096] NVRM: loading NVIDIA UNIX x86 Kernel Module 177.82 Tue Nov 4 13:35:57 PST 2008
[ 15.237236] Bluetooth: Core ver 2.13
[ 15.259729] NET: Registered protocol family 31
[ 15.259733] Bluetooth: HCI device and connection manager initialized
[ 15.259736] Bluetooth: HCI socket layer initialized
[ 15.385763] iTCO_vendor_support: vendor-support=0
[ 15.406577] Linux video capture interface: v2.00
[ 15.411552] Bluetooth: Generic Bluetooth USB driver ver 0.3
[ 15.417072] input: Logitech USB RECEIVER as /devices/virtual/input/input7
[ 15.481111] lmpcm_usb.c: Detected device: Logitech USB RECEIVER
[ 15.481149] usbcore: registered new interface driver lmpcm_usb
[ 15.481152] lmpcm_usb: v0.5.5:USB Logitech MediaPlay Cordless Mouse driver
[ 15.481171] usbcore: registered new interface driver btusb
[ 15.489110] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 15.492776] iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
[ 15.492878] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 15.504565] usbcore: registered new interface driver hiddev
[ 15.529242] usbcore: registered new interface driver usbhid
[ 15.529246] usbhid: v2.6:USB HID core driver
[ 15.536889] input: PC Speaker as /devices/platform/pcspkr/input/input8
[ 15.695186] gspca: main v2.2.0 registered
[ 15.753493] gspca: probing 041e:401c
[ 15.866594] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks
[ 15.866598] iwlagn: Copyright(c) 2003-2008 Intel Corporation
[ 15.866692] iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 15.866721] iwlagn 0000:02:00.0: setting latency timer to 64
[ 15.866760] iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
[ 15.916714] iwlagn: Tunable channels: 11 802.11bg, 13 802.11a channels
[ 15.920099] iwlagn 0000:02:00.0: PCI INT A disabled
[ 15.920520] phy0: Selected rate control algorithm 'iwl-agn-rs'
[ 15.966079] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 15.966105] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 16.001929] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[ 16.004684] zc3xx: probe sif 0x0007
[ 16.009711] zc3xx: probe sensor -> 0f
[ 16.009715] zc3xx: Find Sensor PAS106
[ 16.017559] gspca: probe ok
[ 16.017580] usbcore: registered new interface driver zc3xx
[ 16.017583] zc3xx: registered
[ 16.214001] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x92a0b1, caps: 0xa04713/0x200000
[ 16.249909] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input9
[ 17.636946] lp: driver loaded but no devices found
[ 17.765913] Adding 3220992k swap on /dev/sda5. Priority:-1 extents:1 across:3220992k
[ 18.420586] EXT3 FS on sda2, internal journal
[ 20.134160] type=1505 audit(1233159533.640:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4429
[ 20.198966] type=1505 audit(1233159533.703:3): operation="profile_load" name="/usr/bin/freshclam" name2="default" pid=4434
[ 20.347695] type=1505 audit(1233159533.851:4): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4438
[ 20.347902] type=1505 audit(1233159533.851:5): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4438
[ 20.502735] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 21.074336] ACPI: WMI: Mapper loaded
[ 22.085757] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[ 22.174716] apm: BIOS not found.
[ 22.917095] ppdev: user-space parallel port driver
[ 25.604396] Bluetooth: L2CAP ver 2.11
[ 25.604408] Bluetooth: L2CAP socket layer initialized
[ 25.644677] Bluetooth: RFCOMM socket layer initialized
[ 25.644703] Bluetooth: RFCOMM TTY layer initialized
[ 25.644708] Bluetooth: RFCOMM ver 1.10
[ 25.668264] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 25.668276] Bluetooth: BNEP filters: protocol multicast
[ 25.720274] Bridge firewalling registered
[ 25.737210] Bluetooth: SCO (Voice Link) ver 0.6
[ 25.737216] Bluetooth: SCO socket layer initialized
[ 29.777541] r8169: eth0: link down
[ 29.991166] iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 29.991283] iwlagn 0000:02:00.0: restoring config space at offset 0x1 (was 0x40100102, writing 0x40100106)
[ 29.991454] firmware: requesting iwlwifi-4965-2.ucode
[ 30.401634] Registered led device: iwl-phy0:radio
[ 30.402653] Registered led device: iwl-phy0:assoc
[ 30.402681] Registered led device: iwl-phy0:RX
[ 30.402700] Registered led device: iwl-phy0:TX
[ 31.752641] NET: Registered protocol family 17
[ 63.036696] CPU0 attaching NULL sched-domain.
[ 63.036715] CPU1 attaching NULL sched-domain.
[ 63.040162] CPU0 attaching sched-domain:
[ 63.040171] domain 0: span 0-1 level MC
[ 63.040178] groups: 0 1
[ 63.040192] CPU1 attaching sched-domain:
[ 63.040197] domain 0: span 0-1 level MC
[ 63.040203] groups: 1 0
[ 63.358490] wlan0: authenticate with AP 02:1e:58:41:a4:c0
[ 63.360599] wlan0: authenticated
[ 63.360613] wlan0: associate with AP 02:1e:58:41:a4:c0
[ 63.363622] wlan0: RX AssocResp from 02:1e:58:41:a4:c0 (capab=0x411 status=0 aid=1)
[ 63.363635] wlan0: associated
[ 70.333170] NET: Registered protocol family 10
[ 70.335095] lo: Disabled Privacy Extensions
[ 70.336090] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 81.049050] wlan0: no IPv6 routers present
[ 147.249072] process `skype.real' is using obsolete setsockopt SO_BSDCOMPAT
[ 310.925126] CE: hpet increasing min_delta_ns to 15000 nsec
[ 349.713170] CE: hpet increasing min_delta_ns to 22500 nsec
[ 787.197096] CE: hpet increasing min_delta_ns to 33750 nsec
[ 847.049568] CE: hpet increasing min_delta_ns to 50624 nsec
[ 847.633395] CE: hpet increasing min_delta_ns to 75936 nsec
[ 855.145246] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 855.145253] CSLIP: code copyright 1989 Regents of the University of California.
[ 855.145256] SLIP linefill/keepalive option.
[ 855.249851] PPP generic driver version 2.4.2
[ 855.406816] NET: Registered protocol family 3
[ 855.432236] mkiss: AX.25 Multikiss, Hans Albas PE1AYX
[ 855.525521] AX.25: 6pack driver, Revision: 0.3.0
[ 855.600462] r3964: Philips r3964 Driver $Revision: 1.10 $
[ 855.706436] irda_init()
[ 855.706452] NET: Registered protocol family 23
[ 855.786758] HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
[ 855.786764] N_HDLC line discipline registered.
[ 855.865910] Bluetooth: HCI UART driver ver 2.2
[ 855.865916] Bluetooth: HCI H4 protocol initialized
[ 855.865918] Bluetooth: HCI BCSP protocol initialized
[ 855.865920] Bluetooth: HCILL protocol initialized
[ 855.931060] ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
[ 855.952845] gigaset: Hansjoerg Lipp <hjlipp@web.de>, Tilman Schmidt <tilman@imap.cc>, Stefan Eilers
[ 855.952850] gigaset: Driver for Gigaset 307x
[ 867.609032] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 1065.428094] ACPI: Please implement acpi_video_bus_ROM_seq_show
[ 1065.428660] ACPI: Please implement acpi_video_bus_ROM_seq_show
[ 1339.154513] type=1503 audit(1233160852.659:6): operation="capable" name="sys_admin" pid=8094 profile="/usr/sbin/cupsd"
[ 1339.154526] type=1503 audit(1233160852.659:7): operation="capable" name="sys_resource" pid=8094 profile="/usr/sbin/cupsd"
[ 1339.154533] type=1503 audit(1233160852.659:8): operation="capable" name="sys_rawio" pid=8094 profile="/usr/sbin/cupsd"
[ 1806.609029] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 2263.609035] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 2380.612915] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 2709.609121] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 4364.071754] process `beagled-helper' is using deprecated sysctl (syscall) net.ipv6.neigh.default.retrans_time; Use net.ipv6.neigh.default.retrans_time_ms instead.
[ 4600.609102] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 5479.612088] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 6030.609058] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 6421.609665] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 6910.608493] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 6937.693517] CE: hpet increasing min_delta_ns to 113904 nsec
[ 6971.614504] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 8211.248367] iwlagn: Can not allocate SKB buffers
[ 8356.608085] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 9393.608110] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 9536.608107] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[10603.608132] usb 7-4: reset high speed USB dev
Τελευταία επεξεργασία από linuxman και 28 Ιαν 2009, 22:39, έχει επεξεργασθεί 1 φορά/ες συνολικά
Αιτία: Add tags [code][/code]
Ubuntu 8.10 32bit σε Core2Duo Turbox (Mitac 8227d barebone)
Αγγλικα καλα/γνωσεις προγραμματισμου λιγες/γνωσεις χειρισμου linux μετρια
T7250 2GHz/2GB/GeForce 8600M GS/HDA-Intel 82801H/1440x900/Intel Corporation PRO/4965 AG or AGN [Kedron] Network Connection
LEONDAS
babeTUX
babeTUX
 
Δημοσιεύσεις: 30
Εγγραφή: 21 Ιαν 2009, 14:02
Τοποθεσία: Βολος
Εκτύπωση

Re: καρτα tv gigabyte u8000

Δημοσίευσηαπό LEONDAS » 28 Ιαν 2009, 22:36

Ubuntu 8.10 32bit σε Core2Duo Turbox (Mitac 8227d barebone)
Αγγλικα καλα/γνωσεις προγραμματισμου λιγες/γνωσεις χειρισμου linux μετρια
T7250 2GHz/2GB/GeForce 8600M GS/HDA-Intel 82801H/1440x900/Intel Corporation PRO/4965 AG or AGN [Kedron] Network Connection
LEONDAS
babeTUX
babeTUX
 
Δημοσιεύσεις: 30
Εγγραφή: 21 Ιαν 2009, 14:02
Τοποθεσία: Βολος
Εκτύπωση

Re: καρτα tv gigabyte u8000

Δημοσίευσηαπό LEONDAS » 28 Ιαν 2009, 22:37

LEONDAS έγραψε:και τα βηματα που λεει εδω http://www.linuxtv.org/wiki/index.php/Gigabyte_U8000-RH#Driver_Installation


ειχες ασχοληθει ξανα με αυτο το θεμα εσυ απ οτι ειδα
Ubuntu 8.10 32bit σε Core2Duo Turbox (Mitac 8227d barebone)
Αγγλικα καλα/γνωσεις προγραμματισμου λιγες/γνωσεις χειρισμου linux μετρια
T7250 2GHz/2GB/GeForce 8600M GS/HDA-Intel 82801H/1440x900/Intel Corporation PRO/4965 AG or AGN [Kedron] Network Connection
LEONDAS
babeTUX
babeTUX
 
Δημοσιεύσεις: 30
Εγγραφή: 21 Ιαν 2009, 14:02
Τοποθεσία: Βολος
Εκτύπωση

Re: καρτα tv gigabyte u8000

Δημοσίευσηαπό LEONDAS » 28 Ιαν 2009, 22:41

LEONDAS έγραψε:
LEONDAS έγραψε:και τα βηματα που λεει εδω http://www.linuxtv.org/wiki/index.php/Gigabyte_U8000-RH#Driver_Installation


ειχες ασχοληθει ξανα με αυτο το θεμα εσυ απ οτι ειδα


συγνωμη για πριν αν ετσι ειναι καλυτερα:
Κώδικας: Επιλογή όλων
leo@ubuntux:~$ lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub [8086:2a00] (rev 03)
00:01.0 PCI bridge [0604]: Intel Corporation Mobile PM965/GM965/GL960 PCI Express Root Port [8086:2a01] (rev 03)
00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 [8086:2834] (rev 03)
00:1a.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 [8086:2835] (rev 03)
00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 [8086:283a] (rev 03)
00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 03)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 03)
00:1c.2 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 [8086:2843] (rev 03)
00:1c.3 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 [8086:2845] (rev 03)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 [8086:2830] (rev 03)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 [8086:2831] (rev 03)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 [8086:2832] (rev 03)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 [8086:2836] (rev 03)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev f3)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller [8086:2815] (rev 03)
00:1f.1 IDE interface [0101]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller [8086:2850] (rev 03)
00:1f.2 SATA controller [0106]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller [8086:2829] (rev 03)
00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller [8086:283e] (rev 03)
01:00.0 VGA compatible controller [0300]: nVidia Corporation GeForce 8600M GS [10de:0425] (rev a1)
02:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection [8086:4229] (rev 61)
04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 01)


Κώδικας: Επιλογή όλων
[ 0.903366] bus: 06 index 3 mmio: [0, 0]
[ 0.903368] bus: 08 index 0 mmio: [0, 0]
[ 0.903370] bus: 08 index 1 mmio: [0, 0]
[ 0.903372] bus: 08 index 2 mmio: [0, 0]
[ 0.903374] bus: 08 index 3 io port: [0, ffff]
[ 0.903376] bus: 08 index 4 mmio: [0, ffffffff]
[ 0.903383] NET: Registered protocol family 2
[ 0.916048] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.916274] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.916627] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.916817] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.916820] TCP reno registered
[ 0.920069] NET: Registered protocol family 1
[ 0.920182] checking if image is initramfs... it is
[ 1.605778] Freeing initrd memory: 8012k freed
[ 1.606104] Simple Boot Flag at 0x36 set to 0x1
[ 1.606829] audit: initializing netlink socket (disabled)
[ 1.606852] type=2000 audit(1233166714.604:1): initialized
[ 1.612779] highmem bounce pool size: 64 pages
[ 1.612785] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.614965] VFS: Disk quotas dquot_6.5.1
[ 1.615048] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.615144] msgmni has been set to 1743
[ 1.615258] io scheduler noop registered
[ 1.615260] io scheduler anticipatory registered
[ 1.615263] io scheduler deadline registered
[ 1.615274] io scheduler cfq registered (default)
[ 1.615461] pci 0000:01:00.0: Boot video device
[ 1.615567] pcieport-driver 0000:00:01.0: setting latency timer to 64
[ 1.615606] pcieport-driver 0000:00:01.0: found MSI capability
[ 1.615638] pci_express 0000:00:01.0:pcie00: allocate port service
[ 1.615677] pci_express 0000:00:01.0:pcie02: allocate port service
[ 1.615714] pci_express 0000:00:01.0:pcie03: allocate port service
[ 1.615804] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 1.615855] pcieport-driver 0000:00:1c.0: found MSI capability
[ 1.615906] pci_express 0000:00:1c.0:pcie00: allocate port service
[ 1.615943] pci_express 0000:00:1c.0:pcie02: allocate port service
[ 1.615980] pci_express 0000:00:1c.0:pcie03: allocate port service
[ 1.616095] pcieport-driver 0000:00:1c.2: setting latency timer to 64
[ 1.616146] pcieport-driver 0000:00:1c.2: found MSI capability
[ 1.616196] pci_express 0000:00:1c.2:pcie00: allocate port service
[ 1.616239] pci_express 0000:00:1c.2:pcie02: allocate port service
[ 1.616277] pci_express 0000:00:1c.2:pcie03: allocate port service
[ 1.616387] pcieport-driver 0000:00:1c.3: setting latency timer to 64
[ 1.616439] pcieport-driver 0000:00:1c.3: found MSI capability
[ 1.616489] pci_express 0000:00:1c.3:pcie00: allocate port service
[ 1.616527] pci_express 0000:00:1c.3:pcie02: allocate port service
[ 1.616564] pci_express 0000:00:1c.3:pcie03: allocate port service
[ 1.616890] isapnp: Scanning for PnP cards...
[ 1.971876] isapnp: No Plug & Play device found
[ 2.002158] hpet_resources: 0xfed00000 is busy
[ 2.002224] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 2.004268] brd: module loaded
[ 2.004334] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 2.004447] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.007091] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 2.008153] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.008158] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 2.008161] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 2.008163] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 2.008166] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 2.008461] mice: PS/2 mouse device common for all mice
[ 2.008579] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 2.008610] rtc0: alarms up to one month, y3k, hpet irqs
[ 2.008723] EISA: Probing bus 0 at eisa.0
[ 2.008730] Cannot allocate resource for EISA slot 1
[ 2.008734] Cannot allocate resource for EISA slot 2
[ 2.008736] Cannot allocate resource for EISA slot 3
[ 2.008738] Cannot allocate resource for EISA slot 4
[ 2.008740] Cannot allocate resource for EISA slot 5
[ 2.008755] EISA: Detected 0 cards.
[ 2.008758] cpuidle: using governor ladder
[ 2.008761] cpuidle: using governor menu
[ 2.009261] TCP cubic registered
[ 2.009287] Using IPI No-Shortcut mode
[ 2.009445] registered taskstats version 1
[ 2.009562] Magic number: 9:254:343
[ 2.009613] tty tty60: hash matches
[ 2.009666] rtc_cmos 00:07: setting system clock to 2009-01-28 18:18:35 UTC (1233166715)
[ 2.009669] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.009671] EDD information not available.
[ 2.009898] Freeing unused kernel memory: 424k freed
[ 2.009935] Write protecting the kernel text: 2580k
[ 2.009963] Write protecting the kernel read-only data: 940k
[ 2.049419] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 2.156181] fuse init (API version 7.9)
[ 2.184800] ACPI: SSDT 7FED642B, 027A (r1 PmRef Cpu0Ist 3000 INTL 20050624)
[ 2.185194] ACPI: SSDT 7FED5EFC, 04AA (r1 PmRef Cpu0Cst 3001 INTL 20050624)
[ 2.248337] Monitor-Mwait will be used to enter C-1 state
[ 2.248341] Monitor-Mwait will be used to enter C-2 state
[ 2.248344] Monitor-Mwait will be used to enter C-3 state
[ 2.272134] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 2.272192] processor ACPI0007:00: registered as cooling_device0
[ 2.272196] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 2.272560] ACPI: SSDT 7FED66A5, 00C8 (r1 PmRef Cpu1Ist 3000 INTL 20050624)
[ 2.272913] ACPI: SSDT 7FED63A6, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050624)
[ 2.274021] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 2.274069] processor ACPI0007:01: registered as cooling_device1
[ 2.274073] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 2.276499] Marking TSC unstable due to TSC halts in idle
[ 2.276992] thermal LNXTHERM:01: registered as thermal_zone0
[ 2.278299] ACPI: Thermal Zone [TZ00] (71 C)
[ 2.278697] thermal LNXTHERM:02: registered as thermal_zone1
[ 2.278850] ACPI: Thermal Zone [TZ01] (72 C)
[ 2.656076] usbcore: registered new interface driver usbfs
[ 2.656099] usbcore: registered new interface driver hub
[ 2.667998] usbcore: registered new device driver usb
[ 2.676010] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.676032] r8169 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 2.676054] r8169 0000:04:00.0: setting latency timer to 64
[ 2.676478] eth0: RTL8101e at 0xf884a000, 00:40:d0:d2:2b:d2, XID 34200000 IRQ 219
[ 2.692102] USB Universal Host Controller Interface driver v3.0
[ 2.692155] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.692164] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 2.692169] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 2.692219] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 2.692257] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800
[ 2.692419] usb usb1: configuration #1 chosen from 1 choice
[ 2.692469] hub 1-0:1.0: USB hub found
[ 2.692476] hub 1-0:1.0: 2 ports detected
[ 2.744100] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 2.768189] No dock devices found.
[ 2.789641] SCSI subsystem initialized
[ 2.806179] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 2.806189] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 2.806194] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 2.806218] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 2.806256] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820
[ 2.806350] usb usb2: configuration #1 chosen from 1 choice
[ 2.806377] hub 2-0:1.0: USB hub found
[ 2.806383] hub 2-0:1.0: 2 ports detected
[ 2.829190] libata version 3.00 loaded.
[ 2.908372] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.908390] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 2.908394] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 2.908427] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3
[ 2.912323] ehci_hcd 0000:00:1a.7: debug port 1
[ 2.912330] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 2.912344] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfc204800
[ 2.929074] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.929224] usb usb3: configuration #1 chosen from 1 choice
[ 2.929252] hub 3-0:1.0: USB hub found
[ 2.929261] hub 3-0:1.0: 4 ports detected
[ 3.197565] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 3.197575] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 3.197579] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 3.197609] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 3.197647] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840
[ 3.197741] usb usb4: configuration #1 chosen from 1 choice
[ 3.197765] hub 4-0:1.0: USB hub found
[ 3.197771] hub 4-0:1.0: 2 ports detected
[ 3.369049] usb 3-4: new high speed USB device using ehci_hcd and address 2
[ 3.404171] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 3.404179] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 3.404183] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 3.404206] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
[ 3.404244] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001860
[ 3.404334] usb usb5: configuration #1 chosen from 1 choice
[ 3.404359] hub 5-0:1.0: USB hub found
[ 3.404365] hub 5-0:1.0: 2 ports detected
[ 3.500055] Clocksource tsc unstable (delta = -202046469 ns)
[ 3.508310] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 3.508320] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 3.508324] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.508350] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
[ 3.508381] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001880
[ 3.508479] usb usb6: configuration #1 chosen from 1 choice
[ 3.508503] hub 6-0:1.0: USB hub found
[ 3.508509] hub 6-0:1.0: 2 ports detected
[ 3.517139] usb 3-4: configuration #1 chosen from 1 choice
[ 3.716674] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 3.716689] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 3.716693] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 3.716721] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
[ 3.720627] ehci_hcd 0000:00:1d.7: debug port 1
[ 3.720634] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 3.720640] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfc204c00
[ 3.732082] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 3.732373] usb usb7: configuration #1 chosen from 1 choice
[ 3.732579] hub 7-0:1.0: USB hub found
[ 3.732586] hub 7-0:1.0: 6 ports detected
[ 3.941957] ata_piix 0000:00:1f.1: version 2.12
[ 3.941969] ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 3.942011] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 3.942085] scsi0 : ata_piix
[ 3.942189] scsi1 : ata_piix
[ 3.942876] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18a0 irq 14
[ 3.942879] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18a8 irq 15
[ 4.104504] ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-T20N, WA03, max UDMA/33
[ 4.120487] ata1.00: configured for UDMA/33
[ 4.290966] scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T20N WA03 PQ: 0 ANSI: 5
[ 4.292164] ahci 0000:00:1f.2: version 3.0
[ 4.292180] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 4.292297] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
[ 4.292300] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part
[ 4.292306] ahci 0000:00:1f.2: setting latency timer to 64
[ 4.292507] scsi2 : ahci
[ 4.292598] scsi3 : ahci
[ 4.292672] scsi4 : ahci
[ 4.292782] ata3: SATA max UDMA/133 abar m2048@0xfc204000 port 0xfc204100 irq 218
[ 4.292786] ata4: SATA max UDMA/133 abar m2048@0xfc204000 port 0xfc204180 irq 218
[ 4.292790] ata5: SATA max UDMA/133 abar m2048@0xfc204000 port 0xfc204200 irq 218
[ 4.612105] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.612788] ata3.00: _GTF unexpected object type 0x1
[ 4.667915] ata3.00: ATA-7: WDC WD1600BEVS-00RST0, 04.01G04, max UDMA/133
[ 4.667918] ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 4.668890] ata3.00: _GTF unexpected object type 0x1
[ 4.669075] ata3.00: configured for UDMA/133
[ 4.752076] usb 7-1: new high speed USB device using ehci_hcd and address 2
[ 4.885811] usb 7-1: configuration #1 chosen from 1 choice
[ 5.004615] ata4: SATA link down (SStatus 0 SControl 300)
[ 5.108085] usb 7-3: new high speed USB device using ehci_hcd and address 4
[ 5.241660] usb 7-3: configuration #1 chosen from 1 choice
[ 5.340097] ata5: SATA link down (SStatus 0 SControl 300)
[ 5.352084] usb 7-4: new high speed USB device using ehci_hcd and address 5
[ 5.356160] scsi 2:0:0:0: Direct-Access ATA WDC WD1600BEVS-0 04.0 PQ: 0 ANSI: 5
[ 5.368443] scsi 0:0:0:0: Attached scsi generic sg0 type 5
[ 5.368480] scsi 2:0:0:0: Attached scsi generic sg1 type 0
[ 5.388698] Driver 'sd' needs updating - please use bus_type methods
[ 5.388806] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 5.388821] sd 2:0:0:0: [sda] Write Protect is off
[ 5.388824] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.388849] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.388910] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 5.388924] sd 2:0:0:0: [sda] Write Protect is off
[ 5.388926] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.388950] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.388953] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 5.403778] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.403782] Uniform CD-ROM driver Revision: 3.20
[ 5.403864] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 5.439821] sda1 sda2 sda3 < sda5 >
[ 5.463822] sd 2:0:0:0: [sda] Attached SCSI disk
[ 5.487554] usb 7-4: configuration #1 chosen from 1 choice
[ 5.597066] usb 7-5: new high speed USB device using ehci_hcd and address 6
[ 5.748096] usb 7-5: configuration #1 chosen from 1 choice
[ 5.860264] usbcore: registered new interface driver libusual
[ 5.866404] Initializing USB Mass Storage driver...
[ 5.900282] PM: Starting manual resume from disk
[ 5.900285] PM: Resume from partition 8:5
[ 5.900287] PM: Checking hibernation image.
[ 5.900476] PM: Resume from disk failed.
[ 5.953783] kjournald starting. Commit interval 5 seconds
[ 5.953815] EXT3-fs: mounted filesystem with ordered data mode.
[ 6.100085] usb 4-2: new full speed USB device using uhci_hcd and address 2
[ 6.265847] usb 4-2: configuration #1 chosen from 1 choice
[ 6.267755] hub 4-2:1.0: USB hub found
[ 6.269728] hub 4-2:1.0: 4 ports detected
[ 6.484746] scsi5 : SCSI emulation for USB Mass Storage devices
[ 6.484853] usb-storage: device found at 2
[ 6.484855] usb-storage: waiting for device to settle before scanning
[ 6.724054] usb 6-2: new full speed USB device using uhci_hcd and address 2
[ 6.912571] usb 6-2: configuration #1 chosen from 1 choice
[ 6.915919] scsi6 : SCSI emulation for USB Mass Storage devices
[ 6.916071] usb-storage: device found at 4
[ 6.916073] usb-storage: waiting for device to settle before scanning
[ 6.916094] scsi7 : SCSI emulation for USB Mass Storage devices
[ 6.916160] usb-storage: device found at 5
[ 6.916162] usb-storage: waiting for device to settle before scanning
[ 6.989726] usb 4-2.1: new low speed USB device using uhci_hcd and address 3
[ 7.106840] usb 4-2.1: configuration #1 chosen from 1 choice
[ 7.185725] usb 4-2.2: new low speed USB device using uhci_hcd and address 4
[ 7.323820] usb 4-2.2: configuration #1 chosen from 1 choice
[ 7.405724] usb 4-2.4: new full speed USB device using uhci_hcd and address 5
[ 7.538780] usb 4-2.4: configuration #1 chosen from 1 choice
[ 7.542792] usbcore: registered new interface driver usb-storage
[ 7.542795] USB Mass Storage support registered.
[ 11.484267] usb-storage: device scan complete
[ 11.490191] scsi 5:0:0:0: Direct-Access Generic- SD/MMC/MS/MSPro 1.00 PQ: 0 ANSI: 0 CCS
[ 11.491377] sd 5:0:0:0: [sdb] Attached SCSI removable disk
[ 11.491476] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 11.916265] usb-storage: device scan complete
[ 11.916327] usb-storage: device scan complete
[ 11.928373] scsi 7:0:0:0: Direct-Access Multi Flash Reader 1.00 PQ: 0 ANSI: 0
[ 11.928595] scsi 6:0:0:0: Direct-Access Generic External 2.02 PQ: 0 ANSI: 4
[ 11.929521] sd 6:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
[ 11.930383] sd 6:0:0:0: [sdc] Write Protect is off
[ 11.930386] sd 6:0:0:0: [sdc] Mode Sense: 21 00 00 00
[ 11.930389] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 11.931238] sd 6:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
[ 11.932115] sd 6:0:0:0: [sdc] Write Protect is off
[ 11.932118] sd 6:0:0:0: [sdc] Mode Sense: 21 00 00 00
[ 11.932120] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 11.932124] sdc: sdc1
[ 11.932873] sd 6:0:0:0: [sdc] Attached SCSI disk
[ 11.932953] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 11.933827] sd 7:0:0:0: [sdd] Attached SCSI removable disk
[ 11.933875] sd 7:0:0:0: Attached scsi generic sg4 type 0
[ 13.698940] udevd version 124 started
[ 14.064861] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 14.104195] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 14.148144] Linux agpgart interface v0.103
[ 14.254419] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 14.272026] ACPI: Power Button (FF) [PWRF]
[ 14.272161] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
[ 14.304033] ACPI: Power Button (CM) [PWRB]
[ 14.304117] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input4
[ 14.320080] ACPI: Lid Switch [LID0]
[ 14.320215] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5
[ 14.352030] ACPI: Sleep Button (CM) [SLPB]
[ 14.720241] ACPI: Battery Slot [BAT0] (battery present)
[ 14.724167] acpi device:05: registered as cooling_device2
[ 14.724355] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/device:03/input/input6
[ 14.744028] ACPI: Video Device [VGA0] (multi-head: yes rom: no post: no)
[ 14.841145] ACPI: AC Adapter [AC] (on-line)
[ 14.896321] nvidia: module license 'NVIDIA' taints kernel.
[ 15.235872] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 15.235890] nvidia 0000:01:00.0: setting latency timer to 64
[ 15.236096] NVRM: loading NVIDIA UNIX x86 Kernel Module 177.82 Tue Nov 4 13:35:57 PST 2008
[ 15.237236] Bluetooth: Core ver 2.13
[ 15.259729] NET: Registered protocol family 31
[ 15.259733] Bluetooth: HCI device and connection manager initialized
[ 15.259736] Bluetooth: HCI socket layer initialized
[ 15.385763] iTCO_vendor_support: vendor-support=0
[ 15.406577] Linux video capture interface: v2.00
[ 15.411552] Bluetooth: Generic Bluetooth USB driver ver 0.3
[ 15.417072] input: Logitech USB RECEIVER as /devices/virtual/input/input7
[ 15.481111] lmpcm_usb.c: Detected device: Logitech USB RECEIVER
[ 15.481149] usbcore: registered new interface driver lmpcm_usb
[ 15.481152] lmpcm_usb: v0.5.5:USB Logitech MediaPlay Cordless Mouse driver
[ 15.481171] usbcore: registered new interface driver btusb
[ 15.489110] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 15.492776] iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
[ 15.492878] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 15.504565] usbcore: registered new interface driver hiddev
[ 15.529242] usbcore: registered new interface driver usbhid
[ 15.529246] usbhid: v2.6:USB HID core driver
[ 15.536889] input: PC Speaker as /devices/platform/pcspkr/input/input8
[ 15.695186] gspca: main v2.2.0 registered
[ 15.753493] gspca: probing 041e:401c
[ 15.866594] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks
[ 15.866598] iwlagn: Copyright(c) 2003-2008 Intel Corporation
[ 15.866692] iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 15.866721] iwlagn 0000:02:00.0: setting latency timer to 64
[ 15.866760] iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
[ 15.916714] iwlagn: Tunable channels: 11 802.11bg, 13 802.11a channels
[ 15.920099] iwlagn 0000:02:00.0: PCI INT A disabled
[ 15.920520] phy0: Selected rate control algorithm 'iwl-agn-rs'
[ 15.966079] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 15.966105] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 16.001929] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[ 16.004684] zc3xx: probe sif 0x0007
[ 16.009711] zc3xx: probe sensor -> 0f
[ 16.009715] zc3xx: Find Sensor PAS106
[ 16.017559] gspca: probe ok
[ 16.017580] usbcore: registered new interface driver zc3xx
[ 16.017583] zc3xx: registered
[ 16.214001] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x92a0b1, caps: 0xa04713/0x200000
[ 16.249909] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input9
[ 17.636946] lp: driver loaded but no devices found
[ 17.765913] Adding 3220992k swap on /dev/sda5. Priority:-1 extents:1 across:3220992k
[ 18.420586] EXT3 FS on sda2, internal journal
[ 20.134160] type=1505 audit(1233159533.640:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4429
[ 20.198966] type=1505 audit(1233159533.703:3): operation="profile_load" name="/usr/bin/freshclam" name2="default" pid=4434
[ 20.347695] type=1505 audit(1233159533.851:4): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4438
[ 20.347902] type=1505 audit(1233159533.851:5): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4438
[ 20.502735] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 21.074336] ACPI: WMI: Mapper loaded
[ 22.085757] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[ 22.174716] apm: BIOS not found.
[ 22.917095] ppdev: user-space parallel port driver
[ 25.604396] Bluetooth: L2CAP ver 2.11
[ 25.604408] Bluetooth: L2CAP socket layer initialized
[ 25.644677] Bluetooth: RFCOMM socket layer initialized
[ 25.644703] Bluetooth: RFCOMM TTY layer initialized
[ 25.644708] Bluetooth: RFCOMM ver 1.10
[ 25.668264] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 25.668276] Bluetooth: BNEP filters: protocol multicast
[ 25.720274] Bridge firewalling registered
[ 25.737210] Bluetooth: SCO (Voice Link) ver 0.6
[ 25.737216] Bluetooth: SCO socket layer initialized
[ 29.777541] r8169: eth0: link down
[ 29.991166] iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 29.991283] iwlagn 0000:02:00.0: restoring config space at offset 0x1 (was 0x40100102, writing 0x40100106)
[ 29.991454] firmware: requesting iwlwifi-4965-2.ucode
[ 30.401634] Registered led device: iwl-phy0:radio
[ 30.402653] Registered led device: iwl-phy0:assoc
[ 30.402681] Registered led device: iwl-phy0:RX
[ 30.402700] Registered led device: iwl-phy0:TX
[ 31.752641] NET: Registered protocol family 17
[ 63.036696] CPU0 attaching NULL sched-domain.
[ 63.036715] CPU1 attaching NULL sched-domain.
[ 63.040162] CPU0 attaching sched-domain:
[ 63.040171] domain 0: span 0-1 level MC
[ 63.040178] groups: 0 1
[ 63.040192] CPU1 attaching sched-domain:
[ 63.040197] domain 0: span 0-1 level MC
[ 63.040203] groups: 1 0
[ 63.358490] wlan0: authenticate with AP 02:1e:58:41:a4:c0
[ 63.360599] wlan0: authenticated
[ 63.360613] wlan0: associate with AP 02:1e:58:41:a4:c0
[ 63.363622] wlan0: RX AssocResp from 02:1e:58:41:a4:c0 (capab=0x411 status=0 aid=1)
[ 63.363635] wlan0: associated
[ 70.333170] NET: Registered protocol family 10
[ 70.335095] lo: Disabled Privacy Extensions
[ 70.336090] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 81.049050] wlan0: no IPv6 routers present
[ 147.249072] process `skype.real' is using obsolete setsockopt SO_BSDCOMPAT
[ 310.925126] CE: hpet increasing min_delta_ns to 15000 nsec
[ 349.713170] CE: hpet increasing min_delta_ns to 22500 nsec
[ 787.197096] CE: hpet increasing min_delta_ns to 33750 nsec
[ 847.049568] CE: hpet increasing min_delta_ns to 50624 nsec
[ 847.633395] CE: hpet increasing min_delta_ns to 75936 nsec
[ 855.145246] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 855.145253] CSLIP: code copyright 1989 Regents of the University of California.
[ 855.145256] SLIP linefill/keepalive option.
[ 855.249851] PPP generic driver version 2.4.2
[ 855.406816] NET: Registered protocol family 3
[ 855.432236] mkiss: AX.25 Multikiss, Hans Albas PE1AYX
[ 855.525521] AX.25: 6pack driver, Revision: 0.3.0
[ 855.600462] r3964: Philips r3964 Driver $Revision: 1.10 $
[ 855.706436] irda_init()
[ 855.706452] NET: Registered protocol family 23
[ 855.786758] HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
[ 855.786764] N_HDLC line discipline registered.
[ 855.865910] Bluetooth: HCI UART driver ver 2.2
[ 855.865916] Bluetooth: HCI H4 protocol initialized
[ 855.865918] Bluetooth: HCI BCSP protocol initialized
[ 855.865920] Bluetooth: HCILL protocol initialized
[ 855.931060] ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
[ 855.952845] gigaset: Hansjoerg Lipp <hjlipp@web.de>, Tilman Schmidt <tilman@imap.cc>, Stefan Eilers
[ 855.952850] gigaset: Driver for Gigaset 307x
[ 867.609032] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 1065.428094] ACPI: Please implement acpi_video_bus_ROM_seq_show
[ 1065.428660] ACPI: Please implement acpi_video_bus_ROM_seq_show
[ 1339.154513] type=1503 audit(1233160852.659:6): operation="capable" name="sys_admin" pid=8094 profile="/usr/sbin/cupsd"
[ 1339.154526] type=1503 audit(1233160852.659:7): operation="capable" name="sys_resource" pid=8094 profile="/usr/sbin/cupsd"
[ 1339.154533] type=1503 audit(1233160852.659:8): operation="capable" name="sys_rawio" pid=8094 profile="/usr/sbin/cupsd"
[ 1806.609029] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 2263.609035] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 2380.612915] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 2709.609121] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 4364.071754] process `beagled-helper' is using deprecated sysctl (syscall) net.ipv6.neigh.default.retrans_time; Use net.ipv6.neigh.default.retrans_time_ms instead.
[ 4600.609102] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 5479.612088] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 6030.609058] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 6421.609665] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 6910.608493] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 6937.693517] CE: hpet increasing min_delta_ns to 113904 nsec
[ 6971.614504] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 8211.248367] iwlagn: Can not allocate SKB buffers
[ 8356.608085] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 9393.608110] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 9536.608107] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[10603.608132] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[10770.608133] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[11065.609049] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[11898.609039] usb 7-4: reset high speed USB device using ehci_hcd and address 5
Ubuntu 8.10 32bit σε Core2Duo Turbox (Mitac 8227d barebone)
Αγγλικα καλα/γνωσεις προγραμματισμου λιγες/γνωσεις χειρισμου linux μετρια
T7250 2GHz/2GB/GeForce 8600M GS/HDA-Intel 82801H/1440x900/Intel Corporation PRO/4965 AG or AGN [Kedron] Network Connection
LEONDAS
babeTUX
babeTUX
 
Δημοσιεύσεις: 30
Εγγραφή: 21 Ιαν 2009, 14:02
Τοποθεσία: Βολος
Εκτύπωση

Re: καρτα tv gigabyte u8000

Δημοσίευσηαπό linuxman » 28 Ιαν 2009, 22:54

Δώσε το dmesg ξανά όταν κάρτα είναι συνδεδεμένη στο USB
Οδηγίες προς Νεοεισερχόμενους
1 Γνώσεις Linux: Πολύ καλό ┃ Προγραμματισμού: Ικανοποιητικό ┃ Αγγλικών: Ικανοποιητικό
2 Linux Mint 17.1 Rebecca 3.13.0-37-generic 64bit (el_GR.UTF-8, X-Cinnamon cinnamon)
3 Intel Core i5-2310M CPU @ 2.10GHz ‖ RAM 3866 MiB ‖ Dell Inc. 0D7C51 - Dell Inc. Dell System Vostro 3750
4 Intel 2nd Generation Core Processor Family Integrated Graphics [8086:0116] {i915}
5 wlan0: Intel Centrino Wireless-N 1030 [Rainbow Peak] [8086:008a] (rev 34) ⋮ eth0: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 06)
http://www.greeklug.gr
Άβαταρ μέλους
linuxman
Επίτιμο μέλος
Επίτιμο μέλος
 
Δημοσιεύσεις: 10378
Εγγραφή: 10 Μάιος 2008, 20:41
Τοποθεσία: Thessaloniki / Macedonia / Greece
Εκτύπωση

Re: καρτα tv gigabyte u8000

Δημοσίευσηαπό LEONDAS » 28 Ιαν 2009, 23:10

Κώδικας: Επιλογή όλων
es)
[ 0.916627] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.916817] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.916820] TCP reno registered
[ 0.920069] NET: Registered protocol family 1
[ 0.920182] checking if image is initramfs... it is
[ 1.605778] Freeing initrd memory: 8012k freed
[ 1.606104] Simple Boot Flag at 0x36 set to 0x1
[ 1.606829] audit: initializing netlink socket (disabled)
[ 1.606852] type=2000 audit(1233166714.604:1): initialized
[ 1.612779] highmem bounce pool size: 64 pages
[ 1.612785] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.614965] VFS: Disk quotas dquot_6.5.1
[ 1.615048] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.615144] msgmni has been set to 1743
[ 1.615258] io scheduler noop registered
[ 1.615260] io scheduler anticipatory registered
[ 1.615263] io scheduler deadline registered
[ 1.615274] io scheduler cfq registered (default)
[ 1.615461] pci 0000:01:00.0: Boot video device
[ 1.615567] pcieport-driver 0000:00:01.0: setting latency timer to 64
[ 1.615606] pcieport-driver 0000:00:01.0: found MSI capability
[ 1.615638] pci_express 0000:00:01.0:pcie00: allocate port service
[ 1.615677] pci_express 0000:00:01.0:pcie02: allocate port service
[ 1.615714] pci_express 0000:00:01.0:pcie03: allocate port service
[ 1.615804] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 1.615855] pcieport-driver 0000:00:1c.0: found MSI capability
[ 1.615906] pci_express 0000:00:1c.0:pcie00: allocate port service
[ 1.615943] pci_express 0000:00:1c.0:pcie02: allocate port service
[ 1.615980] pci_express 0000:00:1c.0:pcie03: allocate port service
[ 1.616095] pcieport-driver 0000:00:1c.2: setting latency timer to 64
[ 1.616146] pcieport-driver 0000:00:1c.2: found MSI capability
[ 1.616196] pci_express 0000:00:1c.2:pcie00: allocate port service
[ 1.616239] pci_express 0000:00:1c.2:pcie02: allocate port service
[ 1.616277] pci_express 0000:00:1c.2:pcie03: allocate port service
[ 1.616387] pcieport-driver 0000:00:1c.3: setting latency timer to 64
[ 1.616439] pcieport-driver 0000:00:1c.3: found MSI capability
[ 1.616489] pci_express 0000:00:1c.3:pcie00: allocate port service
[ 1.616527] pci_express 0000:00:1c.3:pcie02: allocate port service
[ 1.616564] pci_express 0000:00:1c.3:pcie03: allocate port service
[ 1.616890] isapnp: Scanning for PnP cards...
[ 1.971876] isapnp: No Plug & Play device found
[ 2.002158] hpet_resources: 0xfed00000 is busy
[ 2.002224] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 2.004268] brd: module loaded
[ 2.004334] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 2.004447] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.007091] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 2.008153] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.008158] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 2.008161] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 2.008163] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 2.008166] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 2.008461] mice: PS/2 mouse device common for all mice
[ 2.008579] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 2.008610] rtc0: alarms up to one month, y3k, hpet irqs
[ 2.008723] EISA: Probing bus 0 at eisa.0
[ 2.008730] Cannot allocate resource for EISA slot 1
[ 2.008734] Cannot allocate resource for EISA slot 2
[ 2.008736] Cannot allocate resource for EISA slot 3
[ 2.008738] Cannot allocate resource for EISA slot 4
[ 2.008740] Cannot allocate resource for EISA slot 5
[ 2.008755] EISA: Detected 0 cards.
[ 2.008758] cpuidle: using governor ladder
[ 2.008761] cpuidle: using governor menu
[ 2.009261] TCP cubic registered
[ 2.009287] Using IPI No-Shortcut mode
[ 2.009445] registered taskstats version 1
[ 2.009562] Magic number: 9:254:343
[ 2.009613] tty tty60: hash matches
[ 2.009666] rtc_cmos 00:07: setting system clock to 2009-01-28 18:18:35 UTC (1233166715)
[ 2.009669] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.009671] EDD information not available.
[ 2.009898] Freeing unused kernel memory: 424k freed
[ 2.009935] Write protecting the kernel text: 2580k
[ 2.009963] Write protecting the kernel read-only data: 940k
[ 2.049419] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 2.156181] fuse init (API version 7.9)
[ 2.184800] ACPI: SSDT 7FED642B, 027A (r1 PmRef Cpu0Ist 3000 INTL 20050624)
[ 2.185194] ACPI: SSDT 7FED5EFC, 04AA (r1 PmRef Cpu0Cst 3001 INTL 20050624)
[ 2.248337] Monitor-Mwait will be used to enter C-1 state
[ 2.248341] Monitor-Mwait will be used to enter C-2 state
[ 2.248344] Monitor-Mwait will be used to enter C-3 state
[ 2.272134] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 2.272192] processor ACPI0007:00: registered as cooling_device0
[ 2.272196] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 2.272560] ACPI: SSDT 7FED66A5, 00C8 (r1 PmRef Cpu1Ist 3000 INTL 20050624)
[ 2.272913] ACPI: SSDT 7FED63A6, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050624)
[ 2.274021] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 2.274069] processor ACPI0007:01: registered as cooling_device1
[ 2.274073] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 2.276499] Marking TSC unstable due to TSC halts in idle
[ 2.276992] thermal LNXTHERM:01: registered as thermal_zone0
[ 2.278299] ACPI: Thermal Zone [TZ00] (71 C)
[ 2.278697] thermal LNXTHERM:02: registered as thermal_zone1
[ 2.278850] ACPI: Thermal Zone [TZ01] (72 C)
[ 2.656076] usbcore: registered new interface driver usbfs
[ 2.656099] usbcore: registered new interface driver hub
[ 2.667998] usbcore: registered new device driver usb
[ 2.676010] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.676032] r8169 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 2.676054] r8169 0000:04:00.0: setting latency timer to 64
[ 2.676478] eth0: RTL8101e at 0xf884a000, 00:40:d0:d2:2b:d2, XID 34200000 IRQ 219
[ 2.692102] USB Universal Host Controller Interface driver v3.0
[ 2.692155] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.692164] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 2.692169] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 2.692219] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 2.692257] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800
[ 2.692419] usb usb1: configuration #1 chosen from 1 choice
[ 2.692469] hub 1-0:1.0: USB hub found
[ 2.692476] hub 1-0:1.0: 2 ports detected
[ 2.744100] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 2.768189] No dock devices found.
[ 2.789641] SCSI subsystem initialized
[ 2.806179] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 2.806189] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 2.806194] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 2.806218] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 2.806256] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820
[ 2.806350] usb usb2: configuration #1 chosen from 1 choice
[ 2.806377] hub 2-0:1.0: USB hub found
[ 2.806383] hub 2-0:1.0: 2 ports detected
[ 2.829190] libata version 3.00 loaded.
[ 2.908372] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.908390] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 2.908394] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 2.908427] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3
[ 2.912323] ehci_hcd 0000:00:1a.7: debug port 1
[ 2.912330] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 2.912344] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfc204800
[ 2.929074] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.929224] usb usb3: configuration #1 chosen from 1 choice
[ 2.929252] hub 3-0:1.0: USB hub found
[ 2.929261] hub 3-0:1.0: 4 ports detected
[ 3.197565] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 3.197575] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 3.197579] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 3.197609] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 3.197647] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840
[ 3.197741] usb usb4: configuration #1 chosen from 1 choice
[ 3.197765] hub 4-0:1.0: USB hub found
[ 3.197771] hub 4-0:1.0: 2 ports detected
[ 3.369049] usb 3-4: new high speed USB device using ehci_hcd and address 2
[ 3.404171] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 3.404179] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 3.404183] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 3.404206] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
[ 3.404244] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001860
[ 3.404334] usb usb5: configuration #1 chosen from 1 choice
[ 3.404359] hub 5-0:1.0: USB hub found
[ 3.404365] hub 5-0:1.0: 2 ports detected
[ 3.500055] Clocksource tsc unstable (delta = -202046469 ns)
[ 3.508310] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 3.508320] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 3.508324] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.508350] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
[ 3.508381] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001880
[ 3.508479] usb usb6: configuration #1 chosen from 1 choice
[ 3.508503] hub 6-0:1.0: USB hub found
[ 3.508509] hub 6-0:1.0: 2 ports detected
[ 3.517139] usb 3-4: configuration #1 chosen from 1 choice
[ 3.716674] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 3.716689] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 3.716693] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 3.716721] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
[ 3.720627] ehci_hcd 0000:00:1d.7: debug port 1
[ 3.720634] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 3.720640] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfc204c00
[ 3.732082] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 3.732373] usb usb7: configuration #1 chosen from 1 choice
[ 3.732579] hub 7-0:1.0: USB hub found
[ 3.732586] hub 7-0:1.0: 6 ports detected
[ 3.941957] ata_piix 0000:00:1f.1: version 2.12
[ 3.941969] ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 3.942011] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 3.942085] scsi0 : ata_piix
[ 3.942189] scsi1 : ata_piix
[ 3.942876] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18a0 irq 14
[ 3.942879] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18a8 irq 15
[ 4.104504] ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-T20N, WA03, max UDMA/33
[ 4.120487] ata1.00: configured for UDMA/33
[ 4.290966] scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T20N WA03 PQ: 0 ANSI: 5
[ 4.292164] ahci 0000:00:1f.2: version 3.0
[ 4.292180] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 4.292297] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
[ 4.292300] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part
[ 4.292306] ahci 0000:00:1f.2: setting latency timer to 64
[ 4.292507] scsi2 : ahci
[ 4.292598] scsi3 : ahci
[ 4.292672] scsi4 : ahci
[ 4.292782] ata3: SATA max UDMA/133 abar m2048@0xfc204000 port 0xfc204100 irq 218
[ 4.292786] ata4: SATA max UDMA/133 abar m2048@0xfc204000 port 0xfc204180 irq 218
[ 4.292790] ata5: SATA max UDMA/133 abar m2048@0xfc204000 port 0xfc204200 irq 218
[ 4.612105] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.612788] ata3.00: _GTF unexpected object type 0x1
[ 4.667915] ata3.00: ATA-7: WDC WD1600BEVS-00RST0, 04.01G04, max UDMA/133
[ 4.667918] ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 4.668890] ata3.00: _GTF unexpected object type 0x1
[ 4.669075] ata3.00: configured for UDMA/133
[ 4.752076] usb 7-1: new high speed USB device using ehci_hcd and address 2
[ 4.885811] usb 7-1: configuration #1 chosen from 1 choice
[ 5.004615] ata4: SATA link down (SStatus 0 SControl 300)
[ 5.108085] usb 7-3: new high speed USB device using ehci_hcd and address 4
[ 5.241660] usb 7-3: configuration #1 chosen from 1 choice
[ 5.340097] ata5: SATA link down (SStatus 0 SControl 300)
[ 5.352084] usb 7-4: new high speed USB device using ehci_hcd and address 5
[ 5.356160] scsi 2:0:0:0: Direct-Access ATA WDC WD1600BEVS-0 04.0 PQ: 0 ANSI: 5
[ 5.368443] scsi 0:0:0:0: Attached scsi generic sg0 type 5
[ 5.368480] scsi 2:0:0:0: Attached scsi generic sg1 type 0
[ 5.388698] Driver 'sd' needs updating - please use bus_type methods
[ 5.388806] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 5.388821] sd 2:0:0:0: [sda] Write Protect is off
[ 5.388824] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.388849] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.388910] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 5.388924] sd 2:0:0:0: [sda] Write Protect is off
[ 5.388926] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.388950] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.388953] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 5.403778] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.403782] Uniform CD-ROM driver Revision: 3.20
[ 5.403864] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 5.439821] sda1 sda2 sda3 < sda5 >
[ 5.463822] sd 2:0:0:0: [sda] Attached SCSI disk
[ 5.487554] usb 7-4: configuration #1 chosen from 1 choice
[ 5.597066] usb 7-5: new high speed USB device using ehci_hcd and address 6
[ 5.748096] usb 7-5: configuration #1 chosen from 1 choice
[ 5.860264] usbcore: registered new interface driver libusual
[ 5.866404] Initializing USB Mass Storage driver...
[ 5.900282] PM: Starting manual resume from disk
[ 5.900285] PM: Resume from partition 8:5
[ 5.900287] PM: Checking hibernation image.
[ 5.900476] PM: Resume from disk failed.
[ 5.953783] kjournald starting. Commit interval 5 seconds
[ 5.953815] EXT3-fs: mounted filesystem with ordered data mode.
[ 6.100085] usb 4-2: new full speed USB device using uhci_hcd and address 2
[ 6.265847] usb 4-2: configuration #1 chosen from 1 choice
[ 6.267755] hub 4-2:1.0: USB hub found
[ 6.269728] hub 4-2:1.0: 4 ports detected
[ 6.484746] scsi5 : SCSI emulation for USB Mass Storage devices
[ 6.484853] usb-storage: device found at 2
[ 6.484855] usb-storage: waiting for device to settle before scanning
[ 6.724054] usb 6-2: new full speed USB device using uhci_hcd and address 2
[ 6.912571] usb 6-2: configuration #1 chosen from 1 choice
[ 6.915919] scsi6 : SCSI emulation for USB Mass Storage devices
[ 6.916071] usb-storage: device found at 4
[ 6.916073] usb-storage: waiting for device to settle before scanning
[ 6.916094] scsi7 : SCSI emulation for USB Mass Storage devices
[ 6.916160] usb-storage: device found at 5
[ 6.916162] usb-storage: waiting for device to settle before scanning
[ 6.989726] usb 4-2.1: new low speed USB device using uhci_hcd and address 3
[ 7.106840] usb 4-2.1: configuration #1 chosen from 1 choice
[ 7.185725] usb 4-2.2: new low speed USB device using uhci_hcd and address 4
[ 7.323820] usb 4-2.2: configuration #1 chosen from 1 choice
[ 7.405724] usb 4-2.4: new full speed USB device using uhci_hcd and address 5
[ 7.538780] usb 4-2.4: configuration #1 chosen from 1 choice
[ 7.542792] usbcore: registered new interface driver usb-storage
[ 7.542795] USB Mass Storage support registered.
[ 11.484267] usb-storage: device scan complete
[ 11.490191] scsi 5:0:0:0: Direct-Access Generic- SD/MMC/MS/MSPro 1.00 PQ: 0 ANSI: 0 CCS
[ 11.491377] sd 5:0:0:0: [sdb] Attached SCSI removable disk
[ 11.491476] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 11.916265] usb-storage: device scan complete
[ 11.916327] usb-storage: device scan complete
[ 11.928373] scsi 7:0:0:0: Direct-Access Multi Flash Reader 1.00 PQ: 0 ANSI: 0
[ 11.928595] scsi 6:0:0:0: Direct-Access Generic External 2.02 PQ: 0 ANSI: 4
[ 11.929521] sd 6:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
[ 11.930383] sd 6:0:0:0: [sdc] Write Protect is off
[ 11.930386] sd 6:0:0:0: [sdc] Mode Sense: 21 00 00 00
[ 11.930389] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 11.931238] sd 6:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
[ 11.932115] sd 6:0:0:0: [sdc] Write Protect is off
[ 11.932118] sd 6:0:0:0: [sdc] Mode Sense: 21 00 00 00
[ 11.932120] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 11.932124] sdc: sdc1
[ 11.932873] sd 6:0:0:0: [sdc] Attached SCSI disk
[ 11.932953] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 11.933827] sd 7:0:0:0: [sdd] Attached SCSI removable disk
[ 11.933875] sd 7:0:0:0: Attached scsi generic sg4 type 0
[ 13.698940] udevd version 124 started
[ 14.064861] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 14.104195] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 14.148144] Linux agpgart interface v0.103
[ 14.254419] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 14.272026] ACPI: Power Button (FF) [PWRF]
[ 14.272161] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
[ 14.304033] ACPI: Power Button (CM) [PWRB]
[ 14.304117] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input4
[ 14.320080] ACPI: Lid Switch [LID0]
[ 14.320215] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5
[ 14.352030] ACPI: Sleep Button (CM) [SLPB]
[ 14.720241] ACPI: Battery Slot [BAT0] (battery present)
[ 14.724167] acpi device:05: registered as cooling_device2
[ 14.724355] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/device:03/input/input6
[ 14.744028] ACPI: Video Device [VGA0] (multi-head: yes rom: no post: no)
[ 14.841145] ACPI: AC Adapter [AC] (on-line)
[ 14.896321] nvidia: module license 'NVIDIA' taints kernel.
[ 15.235872] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 15.235890] nvidia 0000:01:00.0: setting latency timer to 64
[ 15.236096] NVRM: loading NVIDIA UNIX x86 Kernel Module 177.82 Tue Nov 4 13:35:57 PST 2008
[ 15.237236] Bluetooth: Core ver 2.13
[ 15.259729] NET: Registered protocol family 31
[ 15.259733] Bluetooth: HCI device and connection manager initialized
[ 15.259736] Bluetooth: HCI socket layer initialized
[ 15.385763] iTCO_vendor_support: vendor-support=0
[ 15.406577] Linux video capture interface: v2.00
[ 15.411552] Bluetooth: Generic Bluetooth USB driver ver 0.3
[ 15.417072] input: Logitech USB RECEIVER as /devices/virtual/input/input7
[ 15.481111] lmpcm_usb.c: Detected device: Logitech USB RECEIVER
[ 15.481149] usbcore: registered new interface driver lmpcm_usb
[ 15.481152] lmpcm_usb: v0.5.5:USB Logitech MediaPlay Cordless Mouse driver
[ 15.481171] usbcore: registered new interface driver btusb
[ 15.489110] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 15.492776] iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
[ 15.492878] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 15.504565] usbcore: registered new interface driver hiddev
[ 15.529242] usbcore: registered new interface driver usbhid
[ 15.529246] usbhid: v2.6:USB HID core driver
[ 15.536889] input: PC Speaker as /devices/platform/pcspkr/input/input8
[ 15.695186] gspca: main v2.2.0 registered
[ 15.753493] gspca: probing 041e:401c
[ 15.866594] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks
[ 15.866598] iwlagn: Copyright(c) 2003-2008 Intel Corporation
[ 15.866692] iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 15.866721] iwlagn 0000:02:00.0: setting latency timer to 64
[ 15.866760] iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
[ 15.916714] iwlagn: Tunable channels: 11 802.11bg, 13 802.11a channels
[ 15.920099] iwlagn 0000:02:00.0: PCI INT A disabled
[ 15.920520] phy0: Selected rate control algorithm 'iwl-agn-rs'
[ 15.966079] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 15.966105] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 16.001929] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[ 16.004684] zc3xx: probe sif 0x0007
[ 16.009711] zc3xx: probe sensor -> 0f
[ 16.009715] zc3xx: Find Sensor PAS106
[ 16.017559] gspca: probe ok
[ 16.017580] usbcore: registered new interface driver zc3xx
[ 16.017583] zc3xx: registered
[ 16.214001] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x92a0b1, caps: 0xa04713/0x200000
[ 16.249909] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input9
[ 17.636946] lp: driver loaded but no devices found
[ 17.765913] Adding 3220992k swap on /dev/sda5. Priority:-1 extents:1 across:3220992k
[ 18.420586] EXT3 FS on sda2, internal journal
[ 20.134160] type=1505 audit(1233159533.640:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4429
[ 20.198966] type=1505 audit(1233159533.703:3): operation="profile_load" name="/usr/bin/freshclam" name2="default" pid=4434
[ 20.347695] type=1505 audit(1233159533.851:4): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4438
[ 20.347902] type=1505 audit(1233159533.851:5): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4438
[ 20.502735] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 21.074336] ACPI: WMI: Mapper loaded
[ 22.085757] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[ 22.174716] apm: BIOS not found.
[ 22.917095] ppdev: user-space parallel port driver
[ 25.604396] Bluetooth: L2CAP ver 2.11
[ 25.604408] Bluetooth: L2CAP socket layer initialized
[ 25.644677] Bluetooth: RFCOMM socket layer initialized
[ 25.644703] Bluetooth: RFCOMM TTY layer initialized
[ 25.644708] Bluetooth: RFCOMM ver 1.10
[ 25.668264] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 25.668276] Bluetooth: BNEP filters: protocol multicast
[ 25.720274] Bridge firewalling registered
[ 25.737210] Bluetooth: SCO (Voice Link) ver 0.6
[ 25.737216] Bluetooth: SCO socket layer initialized
[ 29.777541] r8169: eth0: link down
[ 29.991166] iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 29.991283] iwlagn 0000:02:00.0: restoring config space at offset 0x1 (was 0x40100102, writing 0x40100106)
[ 29.991454] firmware: requesting iwlwifi-4965-2.ucode
[ 30.401634] Registered led device: iwl-phy0:radio
[ 30.402653] Registered led device: iwl-phy0:assoc
[ 30.402681] Registered led device: iwl-phy0:RX
[ 30.402700] Registered led device: iwl-phy0:TX
[ 31.752641] NET: Registered protocol family 17
[ 63.036696] CPU0 attaching NULL sched-domain.
[ 63.036715] CPU1 attaching NULL sched-domain.
[ 63.040162] CPU0 attaching sched-domain:
[ 63.040171] domain 0: span 0-1 level MC
[ 63.040178] groups: 0 1
[ 63.040192] CPU1 attaching sched-domain:
[ 63.040197] domain 0: span 0-1 level MC
[ 63.040203] groups: 1 0
[ 63.358490] wlan0: authenticate with AP 02:1e:58:41:a4:c0
[ 63.360599] wlan0: authenticated
[ 63.360613] wlan0: associate with AP 02:1e:58:41:a4:c0
[ 63.363622] wlan0: RX AssocResp from 02:1e:58:41:a4:c0 (capab=0x411 status=0 aid=1)
[ 63.363635] wlan0: associated
[ 70.333170] NET: Registered protocol family 10
[ 70.335095] lo: Disabled Privacy Extensions
[ 70.336090] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 81.049050] wlan0: no IPv6 routers present
[ 147.249072] process `skype.real' is using obsolete setsockopt SO_BSDCOMPAT
[ 310.925126] CE: hpet increasing min_delta_ns to 15000 nsec
[ 349.713170] CE: hpet increasing min_delta_ns to 22500 nsec
[ 787.197096] CE: hpet increasing min_delta_ns to 33750 nsec
[ 847.049568] CE: hpet increasing min_delta_ns to 50624 nsec
[ 847.633395] CE: hpet increasing min_delta_ns to 75936 nsec
[ 855.145246] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 855.145253] CSLIP: code copyright 1989 Regents of the University of California.
[ 855.145256] SLIP linefill/keepalive option.
[ 855.249851] PPP generic driver version 2.4.2
[ 855.406816] NET: Registered protocol family 3
[ 855.432236] mkiss: AX.25 Multikiss, Hans Albas PE1AYX
[ 855.525521] AX.25: 6pack driver, Revision: 0.3.0
[ 855.600462] r3964: Philips r3964 Driver $Revision: 1.10 $
[ 855.706436] irda_init()
[ 855.706452] NET: Registered protocol family 23
[ 855.786758] HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
[ 855.786764] N_HDLC line discipline registered.
[ 855.865910] Bluetooth: HCI UART driver ver 2.2
[ 855.865916] Bluetooth: HCI H4 protocol initialized
[ 855.865918] Bluetooth: HCI BCSP protocol initialized
[ 855.865920] Bluetooth: HCILL protocol initialized
[ 855.931060] ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
[ 855.952845] gigaset: Hansjoerg Lipp <hjlipp@web.de>, Tilman Schmidt <tilman@imap.cc>, Stefan Eilers
[ 855.952850] gigaset: Driver for Gigaset 307x
[ 867.609032] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 1065.428094] ACPI: Please implement acpi_video_bus_ROM_seq_show
[ 1065.428660] ACPI: Please implement acpi_video_bus_ROM_seq_show
[ 1339.154513] type=1503 audit(1233160852.659:6): operation="capable" name="sys_admin" pid=8094 profile="/usr/sbin/cupsd"
[ 1339.154526] type=1503 audit(1233160852.659:7): operation="capable" name="sys_resource" pid=8094 profile="/usr/sbin/cupsd"
[ 1339.154533] type=1503 audit(1233160852.659:8): operation="capable" name="sys_rawio" pid=8094 profile="/usr/sbin/cupsd"
[ 1806.609029] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 2263.609035] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 2380.612915] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 2709.609121] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 4364.071754] process `beagled-helper' is using deprecated sysctl (syscall) net.ipv6.neigh.default.retrans_time; Use net.ipv6.neigh.default.retrans_time_ms instead.
[ 4600.609102] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 5479.612088] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 6030.609058] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 6421.609665] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 6910.608493] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 6937.693517] CE: hpet increasing min_delta_ns to 113904 nsec
[ 6971.614504] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 8211.248367] iwlagn: Can not allocate SKB buffers
[ 8356.608085] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 9393.608110] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[ 9536.608107] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[10603.608132] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[10770.608133] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[11065.609049] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[11898.609039] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[12341.608129] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[12446.608103] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[12844.216478] CE: hpet increasing min_delta_ns to 170856 nsec
[12850.412590] CE: hpet increasing min_delta_ns to 256284 nsec
[12973.609059] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[13242.609056] usb 7-4: reset high speed USB device using ehci_hcd and address 5
[13571.523656] iwlagn: Can not allocate SKB buffers
[13572.873191] iwlagn: Can not allocate SKB buffers
[13575.005172] iwlagn: Can not allocate SKB buffers




αυτο εδω πανω ειναι.Στην αρχη ειχε αναψει το λαμπακι αλλα με την αναβαθμηση του πυρηνα εσβησε + οτι δεν το βλεπει το Kaffeine.
Ubuntu 8.10 32bit σε Core2Duo Turbox (Mitac 8227d barebone)
Αγγλικα καλα/γνωσεις προγραμματισμου λιγες/γνωσεις χειρισμου linux μετρια
T7250 2GHz/2GB/GeForce 8600M GS/HDA-Intel 82801H/1440x900/Intel Corporation PRO/4965 AG or AGN [Kedron] Network Connection
LEONDAS
babeTUX
babeTUX
 
Δημοσιεύσεις: 30
Εγγραφή: 21 Ιαν 2009, 14:02
Τοποθεσία: Βολος
Εκτύπωση

Re: καρτα tv gigabyte u8000

Δημοσίευσηαπό logari81 » 28 Ιαν 2009, 23:57

στο dmesg σου δεν φαινεται πουθενα το dib0700 που ειναι ο οδηγος για αυτην την καρτα. Στον φιλο Yianpan που ειχε ρωτησει παλια, υπήρχε αυτος ο οδηγος φορτωμένος. Ισως καποια απο τις δοκιμες που εκανες να εκανε τα πραγματα χειροτερα. Θα μπορουσες να δοκιμασε με ενα LiveCD του Ubuntu 8.10 να συνδεσεις την καρτα και μετα να τρεξεις
Κώδικας: Επιλογή όλων
dmesg |grep dib

και να δεις τι βγαζει.
http://opensourceecology.org/


Λειτουργικό: Ubuntu 10.04 lucid 64-bitΠροδιαγραφές: 4x Intel Core i5 CPU M 450 2.40GHz ‖ RAM 3696 MiB ‖ Lenovo KL3 - LENOVO IdeaPad Y560
Κάρτα γραφικών: ATI Device [1002:68c0]Ασύρματο: wlan0: Atheros Inc. AR928X Wireless Network Adapter (PCI-Express) [168c:002a] (rev 01)
logari81
Επίτιμο μέλος
Επίτιμο μέλος
 
Δημοσιεύσεις: 6074
Εγγραφή: 14 Μάιος 2008, 10:40
Εκτύπωση

Re: καρτα tv gigabyte u8000

Δημοσίευσηαπό LEONDAS » 29 Ιαν 2009, 00:22

φιλε κανοντας boot με τον παλαιο πυρηνα η καρτα δουλεψε (τουλαχιστον τη βλεπει το συστημα + kaffeine σαρωνει αλλα την πριζα της tv εδω την εχω off θα δοκιμασω και στο σαλονι)====> οποτε απ οτι καταλαβα η διαδικασια patchαρε τον παλαιο πυρηνα 2.6.27-9 (εχω τον 2.6.27-11).
Καμμια ιδεα πως να patchαρω και αυτον που εχω?
Η διαδικασια ειναι και εδω

Εγκατάσταση του Gigabyte U8000 σε Ubuntu 8.04 (Hardy Heron) -- the easy way

1.
ΚΩΔΙΚΑΣ
sudo apt-get install linux-headers-generic mercurial
2.
ΚΩΔΙΚΑΣ
cd
(για να μεταφερθούμε στο home directory)
3.
ΚΩΔΙΚΑΣ
hg clone http://linuxtv.org/hg/v4l-dvb
4.
ΚΩΔΙΚΑΣ
cd v4l-dvb/
5.
ΚΩΔΙΚΑΣ
make
6.
ΚΩΔΙΚΑΣ
sudo make install
7.
ΚΩΔΙΚΑΣ
wget http://www.wi-bw.tfh-wildau.de/~pboettc ... 00-1.20.fw
8.
ΚΩΔΙΚΑΣ
wget http://habbit.net/uploads/xc3028-v27.fw
9.
ΚΩΔΙΚΑΣ
sudo mv dvb-usb-dib0700-1.20.fw xc3028-v27.fw /lib/firmware/
10. βγάζουμε και ξαναβάζουμε το usb καλώδιο
11. ανοίγουμε το Kaffeine (ή όποιο άλλο πρόγραμμα προτιμάει ο καθένας) και βλέπουμε τα ψηφιακά κανάλια

Το αρνητικό της συγκεκριμένης κάρτας είναι οτι παρόλο που τα ψηφιακά κανάλια παίζουν μια χαρά, δεν υπάρχει (ακόμα τουλάχιστον) driver για το τσιπάκι CX25843-24Z που είναι υπεύθυνο για την αναλογική τηλεόραση και το ραδιόφωνο
Ubuntu 8.10 32bit σε Core2Duo Turbox (Mitac 8227d barebone)
Αγγλικα καλα/γνωσεις προγραμματισμου λιγες/γνωσεις χειρισμου linux μετρια
T7250 2GHz/2GB/GeForce 8600M GS/HDA-Intel 82801H/1440x900/Intel Corporation PRO/4965 AG or AGN [Kedron] Network Connection
LEONDAS
babeTUX
babeTUX
 
Δημοσιεύσεις: 30
Εγγραφή: 21 Ιαν 2009, 14:02
Τοποθεσία: Βολος
Εκτύπωση

Επόμενο

Επιστροφή στο Περιφερειακά

cron