Crypto PCTV

[Parakoudos]

Καταρχάς χαιρετώ και ξεκινώ με ενα μεγάλο ευχαριστώ για την βοήθεια που πείρα διαβάζοντας από αυτό το φόρουμ.
Είναι το πρώτο μου PC με λειτουργικό ''οχι windows'' και μονο διαβάζοντας απο εδω...
και μπαίνω στο προβληματάκι μου:
ανοιγοντας το TVTIME απο τερματικο μου βγάζει(και ενοείτα ότι δεν ανοίγει):

Κώδικας: Επιλογή όλων

tapis@TAPIS:~$ tvtime
Running tvtime 1.0.2.
Reading configuration from /etc/tvtime/tvtime.xml
Reading configuration from /home/tapis/.tvtime/tvtime.xml
xvoutput: No XVIDEO port found which supports YUY2 images.

*** tvtime requires hardware YUY2 overlay support from your video card
*** driver. If you are using an older NVIDIA card (TNT2), then
*** this capability is only available with their binary drivers.
*** For some ATI cards, this feature may be found in the experimental
*** GATOS drivers: http://gatos.souceforge.net/
*** If unsure, please check with your distribution to see if your
*** X driver supports hardware overlay surfaces.
tapis@TAPIS:~$

Διαβάζοντας το viewtopic.php?f=16&t=1787
εκανα κι εγω τα αντίστοιχα και εβγαλα τα εξης συμπεράσματα:

Κώδικας: Επιλογή όλων

tapis@TAPIS:~$ lspci -nn
00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS780 Host Bridge [1022:9600]
00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) [1022:9602]
00:06.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) [1022:9606]
00:11.0 SATA controller [0106]: ATI Technologies Inc SB700/SB800 SATA Controller [IDE mode] [1002:4390]
00:12.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397]
00:12.1 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI1 Controller [1002:4398]
00:12.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396]
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397]
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI1 Controller [1002:4398]
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396]
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 3a)
00:14.1 IDE interface [0101]: ATI Technologies Inc SB700/SB800 IDE Controller [1002:439c]
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia [1002:4383]
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d]
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384]
00:14.5 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller [1002:4399]
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon HD 3200 Graphics [1002:9610]
01:05.1 Audio device [0403]: ATI Technologies Inc RS780 Azalia controller [1002:960f]
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)
03:07.0 Multimedia controller [0480]: Philips Semiconductors SAA7130 Video Broadcast Decoder [1131:7130] (rev 01)
tapis@TAPIS:~$

και:

Κώδικας: Επιλογή όλων

tapis@TAPIS:~$ lsmod
Module Size Used by
ipv6 267908 8
af_packet 23812 2
ppdev 10372 0
powernow_k8 16704 0
cpufreq_conservative 8712 0
cpufreq_userspace 5284 0
cpufreq_ondemand 9740 1
cpufreq_stats 7104 0
freq_table 5536 3 powernow_k8,cpufreq_ondemand,cpufreq_stats
cpufreq_powersave 2688 0
video 19856 0
output 4736 1 video
sbs 15112 0
dock 11280 0
container 5632 0
sbshc 7680 1 sbs
battery 14212 0
iptable_filter 3840 0
ip_tables 14820 1 iptable_filter
x_tables 16132 1 ip_tables
ac 6916 0
parport_pc 36260 0
lp 12324 0
parport 37832 3 ppdev,parport_pc,lp
psmouse 40336 0
serio_raw 7940 0
pcspkr 4224 0
saa7134_alsa 15424 0
saa7134 131920 1 saa7134_alsa
k8temp 6656 0
compat_ioctl32 2304 1 saa7134
videobuf_dma_sg 14980 2 saa7134_alsa,saa7134
videobuf_core 18820 2 saa7134,videobuf_dma_sg
ir_kbd_i2c 10768 1 saa7134
ir_common 36100 2 saa7134,ir_kbd_i2c
videodev 29440 1 saa7134
v4l2_common 18304 2 saa7134,videodev
v4l1_compat 15492 2 saa7134,videodev
snd_hda_intel 346136 3
snd_pcm_oss 42144 0
snd_mixer_oss 17920 1 snd_pcm_oss
evdev 13056 4
i2c_piix4 9612 0
snd_pcm 78596 3 saa7134_alsa,snd_hda_intel,snd_pcm_oss
i2c_core 24832 3 saa7134,ir_kbd_i2c,i2c_piix4
snd_seq_dummy 4868 0
snd_page_alloc 11400 2 snd_hda_intel,snd_pcm
snd_hwdep 10500 1 snd_hda_intel
snd_seq_oss 35584 0
snd_seq_midi 9376 0
snd_rawmidi 25760 1 snd_seq_midi
snd_seq_midi_event 8320 2 snd_seq_oss,snd_seq_midi
fglrx 1555468 27
snd_seq 54224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 24836 2 snd_pcm,snd_seq
snd_seq_device 9612 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 56996 18 saa7134_alsa,snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_dummy,snd_hwdep,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
agpgart 34760 1 fglrx
soundcore 8800 1 snd
wmi_acer 9644 0
button 9232 0
shpchp 34452 0
pci_hotplug 30880 1 shpchp
ext3 136840 1
jbd 48404 1 ext3
mbcache 9600 1 ext3
ata_generic 8324 0
pata_atiixp 8960 0
pata_acpi 8320 0
usbhid 32128 0
hid 38784 1 usbhid
sg 36880 0
sr_mod 17956 0
cdrom 37408 1 sr_mod
sd_mod 30720 2
floppy 59588 0
atiixp 5648 0 [permanent]
ide_core 113996 1 atiixp
ehci_hcd 37900 0
ohci_hcd 26640 0
ahci 28548 1
r8169 33156 0
usbcore 146412 4 usbhid,ehci_hcd,ohci_hcd
libata 159600 4 ata_generic,pata_atiixp,pata_acpi,ahci
scsi_mod 151436 4 sg,sr_mod,sd_mod,libata
thermal 16796 0
processor 36488 2 powernow_k8,thermal
fan 5636 0
fbcon 42912 0
tileblit 3456 1 fbcon
font 9472 1 fbcon
bitblit 6784 1 fbcon
softcursor 3072 1 bitblit
fuse 50708 3
tapis@TAPIS:~$


Αν είχε κάποιος να σχολιάσει κατι για να βγάλω καμια ακρη θα το εκτιμούσα πολυ...αν οχι...δεν βαριέσαι... θα την ξυλώσω την καρτα...

[logari81]

για το σφαλμα του tvtime, η καρτα γραφικών σου:

01:05.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon HD 3200 Graphics [1002:9610]

για να υποστηριξει xvideo το οποιο απαιτειται απο το tvtime χρειαζεται τους κλειστους οδηγους που μπορεις να βρεις στο System--Administration--Hardware Drivers.

Για την καρτα τηλεόρασης

03:07.0 Multimedia controller [0480]: Philips Semiconductors SAA7130 Video Broadcast Decoder [1131:7130] (rev 01)

δωσε μας και το αποτελεσμα της εντολής

Κώδικας: Επιλογή όλων

dmesg

και δοκιμασε την εκτος απο το tvtime και με το xawtv.

[Parakoudos]

Κώδικας: Επιλογή όλων

[ 27.798157] Calibrating delay using timer specific routine.. 4414.90 BogoMIPS (lpj=8829814)
[ 27.798175] Security Framework initialized
[ 27.798180] SELinux: Disabled at boot.
[ 27.798192] AppArmor: AppArmor initialized
[ 27.798195] Failure registering capabilities with primary security module.
[ 27.798202] Mount-cache hash table entries: 512
[ 27.798295] Initializing cgroup subsys ns
[ 27.798298] Initializing cgroup subsys cpuacct
[ 27.798305] CPU: After generic identify, caps: 078bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001d 00000000
[ 27.798313] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 27.798315] CPU: L2 Cache: 1024K (64 bytes/line)
[ 27.798317] CPU: After all inits, caps: 078bfbff ebd3fbff 00000000 00020410 00002001 00000000 0000001d 00000000
[ 27.798325] Compat vDSO mapped to ffffe000.
[ 27.798334] Checking 'hlt' instruction... OK.
[ 27.814379] SMP alternatives: switching to UP code
[ 27.815324] Freeing SMP alternatives: 11k freed
[ 27.815416] Early unpacking initramfs... done
[ 28.089452] ACPI: Core revision 20070126
[ 28.089527] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 28.092194] CPU0: AMD Athlon(tm) Processor LE-1600 stepping 03
[ 28.092205] Total of 1 processors activated (4414.90 BogoMIPS).
[ 28.092346] ENABLING IO-APIC IRQs
[ 28.092506] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 28.237954] Brought up 1 CPUs
[ 28.237969] CPU0 attaching sched-domain:
[ 28.237971] domain 0: span 01
[ 28.237972] groups: 01
[ 28.238089] net_namespace: 64 bytes
[ 28.238095] Booting paravirtualized kernel on bare hardware
[ 28.238458] Time: 21:05:55 Date: 03/11/09
[ 28.238474] NET: Registered protocol family 16
[ 28.238606] EISA bus registered
[ 28.238609] ACPI: bus type pci registered
[ 28.239179] PCI: BIOS BUG #0[49435000] found
[ 28.239214] PCI: Using configuration type 1
[ 28.239222] Setting up standard PCI resources
[ 28.246815] ACPI: EC: Look up EC in DSDT
[ 28.251118] ACPI: Interpreter enabled
[ 28.251120] ACPI: (supports S0 S1 S3 S4 S5)
[ 28.251133] ACPI: Using IOAPIC for interrupt routing
[ 28.251421] Error attaching device data
[ 28.251426] Error attaching device data
[ 28.251430] Error attaching device data
[ 28.251434] Error attaching device data
[ 28.257992] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 28.258175] pci 0000:00:11.0: set SATA to AHCI mode
[ 28.259221] PCI: Transparent bridge - 0000:00:14.4
[ 28.259245] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 28.259418] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 28.259501] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE6._PRT]
[ 28.259590] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT]
[ 28.262303] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 7 10 11 12 14 15) *0, disabled.
[ 28.262409] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 7 10 11 12 14 15) *0, disabled.
[ 28.262513] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 7 10 11 12 14 15) *0, disabled.
[ 28.262616] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 7 10 11 12 14 15) *0, disabled.
[ 28.262720] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 7 10 11 12 14 15) *0, disabled.
[ 28.262823] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 7 10 11 12 14 15) *0, disabled.
[ 28.262929] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 7 10 11 12 14 15) *0, disabled.
[ 28.263033] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 7 10 11 12 14 15) *0, disabled.
[ 28.263123] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - CD, should be C4 [20070126]
[ 28.263130] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 28.263149] pnp: PnP ACPI init
[ 28.263154] ACPI: bus type pnp registered
[ 28.266764] pnp: PnP ACPI: found 16 devices
[ 28.266766] ACPI: ACPI bus type pnp unregistered
[ 28.266769] PnPBIOS: Disabled by ACPI PNP
[ 28.266912] PCI: Using ACPI for IRQ routing
[ 28.266914] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 28.277913] NET: Registered protocol family 8
[ 28.277915] NET: Registered protocol family 20
[ 28.277942] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 28.277945] hpet0: 4 32-bit timers, 14318180 Hz
[ 28.278974] AppArmor: AppArmor Filesystem Enabled
[ 28.281900] Time: tsc clocksource has been installed.
[ 28.289919] system 00:01: iomem range 0x0-0x0 could not be reserved
[ 28.289922] system 00:01: iomem range 0x70000000-0x7fffffff has been reserved
[ 28.289929] system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
[ 28.289931] system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved
[ 28.289935] system 00:0b: ioport range 0x4d0-0x4d1 has been reserved
[ 28.289938] system 00:0b: ioport range 0x40b-0x40b has been reserved
[ 28.289940] system 00:0b: ioport range 0x4d6-0x4d6 has been reserved
[ 28.289942] system 00:0b: ioport range 0xc00-0xc01 has been reserved
[ 28.289944] system 00:0b: ioport range 0xc14-0xc14 has been reserved
[ 28.289946] system 00:0b: ioport range 0xc50-0xc51 has been reserved
[ 28.289948] system 00:0b: ioport range 0xc52-0xc52 has been reserved
[ 28.289950] system 00:0b: ioport range 0xc6c-0xc6c has been reserved
[ 28.289952] system 00:0b: ioport range 0xc6f-0xc6f has been reserved
[ 28.289955] system 00:0b: ioport range 0xcd0-0xcd1 has been reserved
[ 28.289957] system 00:0b: ioport range 0xcd2-0xcd3 has been reserved
[ 28.289959] system 00:0b: ioport range 0xcd4-0xcd5 has been reserved
[ 28.289961] system 00:0b: ioport range 0xcd6-0xcd7 has been reserved
[ 28.289963] system 00:0b: ioport range 0xcd8-0xcdf has been reserved
[ 28.289965] system 00:0b: ioport range 0x800-0x89f has been reserved
[ 28.289967] system 00:0b: ioport range 0xb00-0xb3f has been reserved
[ 28.289970] system 00:0b: ioport range 0x900-0x90f has been reserved
[ 28.289972] system 00:0b: ioport range 0x910-0x91f has been reserved
[ 28.289974] system 00:0b: ioport range 0xfe00-0xfefe has been reserved
[ 28.289977] system 00:0b: iomem range 0xffb80000-0xffbfffff could not be reserved
[ 28.289979] system 00:0b: iomem range 0xfec10000-0xfec1001f has been reserved
[ 28.289984] system 00:0d: ioport range 0xe00-0xe0f has been reserved
[ 28.289986] system 00:0d: ioport range 0xe80-0xe8f has been reserved
[ 28.289988] system 00:0d: ioport range 0xf40-0xf4f has been reserved
[ 28.289990] system 00:0d: ioport range 0xa30-0xa3f has been reserved
[ 28.289994] system 00:0e: iomem range 0xe0000000-0xefffffff has been reserved
[ 28.289999] system 00:0f: iomem range 0x0-0x9ffff could not be reserved
[ 28.290001] system 00:0f: iomem range 0xc0000-0xcffff could not be reserved
[ 28.290004] system 00:0f: iomem range 0xe0000-0xfffff could not be reserved
[ 28.290006] system 00:0f: iomem range 0x100000-0x6fffffff could not be reserved
[ 28.290008] system 00:0f: iomem range 0xfec00000-0xffffffff could not be reserved
[ 28.320276] PCI: Bridge: 0000:00:01.0
[ 28.320278] IO window: d000-dfff
[ 28.320281] MEM window: fe800000-fe9fffff
[ 28.320283] PREFETCH window: d0000000-dfffffff
[ 28.320286] PCI: Bridge: 0000:00:06.0
[ 28.320288] IO window: e000-efff
[ 28.320290] MEM window: fea00000-feafffff
[ 28.320293] PREFETCH window: fdf00000-fdffffff
[ 28.320295] PCI: Bridge: 0000:00:14.4
[ 28.320296] IO window: disabled.
[ 28.320301] MEM window: feb00000-febfffff
[ 28.320304] PREFETCH window: disabled.
[ 28.320321] ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 18 (level, low) -> IRQ 16
[ 28.320325] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 28.320338] NET: Registered protocol family 2
[ 28.325881] Switched to high resolution mode on CPU 0
[ 28.357888] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 28.358112] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 28.358773] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 28.359067] TCP: Hash tables configured (established 131072 bind 65536)
[ 28.359069] TCP reno registered
[ 28.369938] checking if image is initramfs... it is
[ 28.899559] Freeing initrd memory: 7319k freed
[ 28.899998] audit: initializing netlink socket (disabled)
[ 28.900007] audit(1236805555.076:1): initialized
[ 28.900131] highmem bounce pool size: 64 pages
[ 28.901437] VFS: Disk quotas dquot_6.5.1
[ 28.901489] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 28.901585] io scheduler noop registered
[ 28.901587] io scheduler anticipatory registered
[ 28.901588] io scheduler deadline registered
[ 28.901596] io scheduler cfq registered (default)
[ 29.045477] Boot video device is 0000:01:05.0
[ 29.045556] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 29.045577] assign_interrupt_mode Found MSI capability
[ 29.045599] Allocate Port Service[0000:00:06.0:pcie00]
[ 29.045622] Allocate Port Service[0000:00:06.0:pcie02]
[ 29.045771] isapnp: Scanning for PnP cards...
[ 29.399573] isapnp: No Plug & Play device found
[ 29.419542] Real Time Clock Driver v1.12ac
[ 29.419684] hpet_resources: 0xfed00000 is busy
[ 29.419703] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 29.419832] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 29.420331] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 29.420846] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 29.420893] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 29.420959] PNP: PS/2 Controller [PNP0303:PSKE,PNP0f03:PSMS] at 0x60,0x64 irq 1,12
[ 29.421266] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 29.421269] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 29.425436] mice: PS/2 mouse device common for all mice
[ 29.425512] EISA: Probing bus 0 at eisa.0
[ 29.425546] Cannot allocate resource for EISA slot 8
[ 29.425547] EISA: Detected 0 cards.
[ 29.425550] cpuidle: using governor ladder
[ 29.425551] cpuidle: using governor menu
[ 29.425614] NET: Registered protocol family 1
[ 29.425633] Using IPI No-Shortcut mode
[ 29.425655] registered taskstats version 1
[ 29.425739] Magic number: 1:548:95
[ 29.425843] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 29.425845] EDD information not available.
[ 29.426060] Freeing unused kernel memory: 368k freed
[ 29.426079] Write protecting the kernel read-only data: 806k
[ 30.595987] fuse init (API version 7.9)
[ 30.610575] ACPI: Processor [P001] (supports 8 throttling states)
[ 30.610585] ACPI Exception (processor_core-0822): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 30.610594] ACPI Exception (processor_core-0822): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 30.610603] ACPI Exception (processor_core-0822): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 31.052554] SCSI subsystem initialized
[ 31.092327] libata version 3.00 loaded.
[ 31.108365] usbcore: registered new interface driver usbfs
[ 31.108382] usbcore: registered new interface driver hub
[ 31.112355] r8169 Gigabit Ethernet driver 2.2LK loaded
[ 31.112374] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 18 (level, low) -> IRQ 16
[ 31.112387] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 31.112607] eth0: RTL8168c/8111c at 0xf8856000, 00:22:15:95:c3:83, XID 3c4000c0 IRQ 222
[ 31.124341] usbcore: registered new device driver usb
[ 31.132343] ahci 0000:00:11.0: version 3.0
[ 31.132369] ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 22 (level, low) -> IRQ 17
[ 31.132418] ahci 0000:00:11.0: controller can't do PMP, turning off CAP_PMP
[ 31.140321] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 31.164032] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 31.164037] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 31.308517] Floppy drive(s): fd0 is 1.44M
[ 31.327978] FDC 0 is a post-1991 82077
[ 32.135772] ahci 0000:00:11.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 32.135776] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pio slum part
[ 32.136078] scsi0 : ahci
[ 32.136241] scsi1 : ahci
[ 32.136341] scsi2 : ahci
[ 32.136436] scsi3 : ahci
[ 32.136461] ata1: SATA max UDMA/133 abar m1024@0xfe7ff800 port 0xfe7ff900 irq 221
[ 32.136465] ata2: SATA max UDMA/133 abar m1024@0xfe7ff800 port 0xfe7ff980 irq 221
[ 32.136468] ata3: SATA max UDMA/133 abar m1024@0xfe7ff800 port 0xfe7ffa00 irq 221
[ 32.136472] ata4: SATA max UDMA/133 abar m1024@0xfe7ff800 port 0xfe7ffa80 irq 221
[ 32.611474] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 32.612299] ata1.00: ATA-8: WDC WD5000AAKS-00A7B2, 01.03B01, max UDMA/133
[ 32.612301] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (not used)
[ 32.613185] ata1.00: configured for UDMA/133
[ 32.923297] ata2: SATA link down (SStatus 0 SControl 300)
[ 33.235121] ata3: SATA link down (SStatus 0 SControl 300)
[ 33.710852] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 33.867492] ata4.00: ATAPI: TSSTcorp CDDVDW SH-S223F, SB00, max UDMA/100, ATAPI AN
[ 34.023399] ata4.00: configured for UDMA/100
[ 34.023466] scsi 0:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 01.0 PQ: 0 ANSI: 5
[ 34.024018] scsi 3:0:0:0: CD-ROM TSSTcorp CDDVDW SH-S223F SB00 PQ: 0 ANSI: 5
[ 34.025412] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 16 (level, low) -> IRQ 18
[ 34.025423] ohci_hcd 0000:00:12.0: OHCI Host Controller
[ 34.025658] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 1
[ 34.025675] ohci_hcd 0000:00:12.0: irq 18, io mem 0xfe7fe000
[ 34.032791] Driver 'sd' needs updating - please use bus_type methods
[ 34.035633] Driver 'sr' needs updating - please use bus_type methods
[ 34.038708] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 34.038718] sd 0:0:0:0: [sda] Write Protect is off
[ 34.038720] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 34.038731] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 34.038765] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 34.038772] sd 0:0:0:0: [sda] Write Protect is off
[ 34.038774] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 34.038784] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 34.038787] sda: sda1 sda2 < sda5 sda6 sda7<6>usb usb1: configuration #1 chosen from 1 choice
[ 34.082729] hub 1-0:1.0: USB hub found
[ 34.082736] hub 1-0:1.0: 3 ports detected
[ 34.089184] sda8 sda9 sda10 > sda3
[ 34.104612] sd 0:0:0:0: [sda] Attached SCSI disk
[ 34.108984] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 34.108998] sr 3:0:0:0: Attached scsi generic sg1 type 5
[ 34.111635] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 34.111638] Uniform CD-ROM driver Revision: 3.20
[ 34.111673] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 34.186652] ACPI: PCI Interrupt 0000:00:12.1[A] -> GSI 16 (level, low) -> IRQ 18
[ 34.186667] ohci_hcd 0000:00:12.1: OHCI Host Controller
[ 34.186686] ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 2
[ 34.186700] ohci_hcd 0000:00:12.1: irq 18, io mem 0xfe7fd000
[ 34.246622] usb usb2: configuration #1 chosen from 1 choice
[ 34.246640] hub 2-0:1.0: USB hub found
[ 34.246648] hub 2-0:1.0: 3 ports detected
[ 34.350543] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 16
[ 34.350556] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 34.350572] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 3
[ 34.350588] ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe7fc000
[ 34.410502] usb usb3: configuration #1 chosen from 1 choice
[ 34.410520] hub 3-0:1.0: USB hub found
[ 34.410526] hub 3-0:1.0: 3 ports detected
[ 34.498404] usb 1-3: new low speed USB device using ohci_hcd and address 2
[ 34.514462] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 18 (level, low) -> IRQ 16
[ 34.514475] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 34.514492] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 4
[ 34.514506] ohci_hcd 0000:00:13.1: irq 16, io mem 0xfe7fb000
[ 34.574430] usb usb4: configuration #1 chosen from 1 choice
[ 34.574448] hub 4-0:1.0: USB hub found
[ 34.574455] hub 4-0:1.0: 3 ports detected
[ 34.678371] ACPI: PCI Interrupt 0000:00:14.5[C] -> GSI 18 (level, low) -> IRQ 16
[ 34.678384] ohci_hcd 0000:00:14.5: OHCI Host Controller
[ 34.678400] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 5
[ 34.678414] ohci_hcd 0000:00:14.5: irq 16, io mem 0xfe7f9000
[ 34.720754] usb 1-3: configuration #1 chosen from 1 choice
[ 34.738317] usb usb5: configuration #1 chosen from 1 choice
[ 34.738332] hub 5-0:1.0: USB hub found
[ 34.738339] hub 5-0:1.0: 2 ports detected
[ 34.843117] ATIIXP: IDE controller (0x1002:0x439c rev 0x00) at PCI slot 0000:00:14.1
[ 34.843130] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 18
[ 34.843137] ATIIXP: not 100% native mode: will probe irqs later
[ 34.843144] ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:pio, hdb:pio
[ 34.843156] ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:pio, hdd:pio
[ 34.843163] Probing IDE interface ide0...
[ 34.917547] usbcore: registered new interface driver hiddev
[ 34.921217] input: Microsoft Microsoft Wireless Optical Desktop� 2.10 as /devices/pci0000:00/0000:00:12.0/usb1/1-3/1-3:1.0/input/input1
[ 34.930181] input,hidraw0: USB HID v1.11 Keyboard [Microsoft Microsoft Wireless Optical Desktop� 2.10] on usb-0000:00:12.0-3
[ 34.959072] input: Microsoft Microsoft Wireless Optical Desktop� 2.10 as /devices/pci0000:00/0000:00:12.0/usb1/1-3/1-3:1.1/input/input2
[ 34.982147] input,hidraw1: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Desktop� 2.10] on usb-0000:00:12.0-3
[ 34.982158] usbcore: registered new interface driver usbhid
[ 34.982161] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 35.409916] Probing IDE interface ide1...
[ 35.979578] ACPI: PCI Interrupt 0000:00:12.2[B] -> GSI 17 (level, low) -> IRQ 19
[ 35.979588] ehci_hcd 0000:00:12.2: EHCI Host Controller
[ 35.979609] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 6
[ 35.979644] ehci_hcd 0000:00:12.2: debug port 1
[ 35.979655] ehci_hcd 0000:00:12.2: irq 19, io mem 0xfe7ff000
[ 35.979700] usb 1-3: USB disconnect, address 2
[ 35.989569] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 35.989650] usb usb6: configuration #1 chosen from 1 choice
[ 35.989668] hub 6-0:1.0: USB hub found
[ 35.989672] hub 6-0:1.0: 6 ports detected
[ 36.093565] ACPI: PCI Interrupt 0000:00:13.2[B] -> GSI 19 (level, low) -> IRQ 20
[ 36.093577] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 36.093593] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 7
[ 36.093625] ehci_hcd 0000:00:13.2: debug port 1
[ 36.093634] ehci_hcd 0000:00:13.2: irq 20, io mem 0xfe7fa800
[ 36.105495] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 36.105555] usb usb7: configuration #1 chosen from 1 choice
[ 36.105571] hub 7-0:1.0: USB hub found
[ 36.105575] hub 7-0:1.0: 6 ports detected
[ 36.713153] usb 1-3: new low speed USB device using ohci_hcd and address 3
[ 36.934982] usb 1-3: configuration #1 chosen from 1 choice
[ 36.942047] input: Microsoft Microsoft Wireless Optical Desktop� 2.10 as /devices/pci0000:00/0000:00:12.0/usb1/1-3/1-3:1.0/input/input3
[ 36.953057] input,hidraw0: USB HID v1.11 Keyboard [Microsoft Microsoft Wireless Optical Desktop� 2.10] on usb-0000:00:12.0-3
[ 36.981894] input: Microsoft Microsoft Wireless Optical Desktop� 2.10 as /devices/pci0000:00/0000:00:12.0/usb1/1-3/1-3:1.1/input/input4
[ 37.009019] input,hidraw1: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Desktop� 2.10] on usb-0000:00:12.0-3
[ 41.414504] kjournald starting. Commit interval 5 seconds
[ 41.414513] EXT3-fs: mounted filesystem with ordered data mode.
[ 45.852040] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 45.896059] shpchp: HPC vendor_id 1022 device_id 9602 ss_vid 0 ss_did 0
[ 45.896063] shpchp: shpc_init: cannot reserve MMIO region
[ 45.896116] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 46.175960] input: Power Button (FF) as /devices/virtual/input/input5
[ 46.195811] ACPI: Power Button (FF) [PWRF]
[ 46.195905] input: Power Button (CM) as /devices/virtual/input/input6
[ 46.207803] ACPI: Power Button (CM) [PWRB]
[ 46.224166] ACPI: WMI-Acer: Mapper loaded
[ 47.051352] Linux agpgart interface v0.102
[ 47.255908] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[ 47.359182] [fglrx] Maximum main memory to use for locked dma buffers: 1656 MBytes.
[ 47.359211] [fglrx] ASYNCIO init succeed!
[ 47.359379] [fglrx] PAT is enabled successfully!
[ 47.362610] [fglrx] module loaded - fglrx 8.47.3 [Feb 25 2008] on minor 0
[ 47.842933] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[ 47.954891] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 18
[ 47.980650] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[ 48.012738] ACPI: PCI Interrupt 0000:01:05.1[B] -> GSI 19 (level, low) -> IRQ 20
[ 48.012756] PCI: Setting latency timer of device 0000:01:05.1 to 64
[ 48.258825] Linux video capture interface: v2.00
[ 48.494531] saa7130/34: v4l2 driver version 0.2.14 loaded
[ 48.494587] ACPI: PCI Interrupt 0000:03:07.0[A] -> GSI 22 (level, low) -> IRQ 17
[ 48.494596] saa7130[0]: found at 0000:03:07.0, rev: 1, irq: 17, latency: 64, mmio: 0xfebffc00
[ 48.494602] saa7130[0]: subsystem: 1131:203e, board: UNKNOWN/GENERIC [card=0,autodetected]
[ 48.494615] saa7130[0]: board init: gpio is 4131ff
[ 48.630435] saa7130[0]: i2c eeprom 00: 31 11 3e 20 08 20 1c 55 43 43 a9 1c 55 43 43 a9
[ 48.630442] saa7130[0]: i2c eeprom 10: ff ff 00 00 31 30 4d 4f 4f 4e 53 37 31 33 30 20
[ 48.630448] saa7130[0]: i2c eeprom 20: 41 3e 48 53 ff ff ff ff ff ff ff ff ff ff ff ff
[ 48.630453] saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 48.630458] saa7130[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 48.630463] saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 48.630468] saa7130[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 48.630473] saa7130[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 48.630540] saa7130[0]: registered device video0 [v4l2]
[ 48.630572] saa7130[0]: registered device vbi0
[ 48.666180] saa7134 ALSA driver for DMA sound loaded
[ 48.666202] saa7130[0]/alsa: saa7130[0] at 0xfebffc00 irq 17 registered as card -2
[ 48.682836] input: PC Speaker as /devices/platform/pcspkr/input/input7
[ 49.931136] lp: driver loaded but no devices found
[ 50.738715] EXT3 FS on sda9, internal journal
[ 51.642054] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 51.894287] No dock devices found.
[ 52.145340] powernow-k8: Found 1 AMD Athlon(tm) Processor LE-1600 processors (1 cpu cores) (version 2.20.00)
[ 52.145370] powernow-k8: 0 : fid 0xe (2200 MHz), vid 0xc
[ 52.145372] powernow-k8: 1 : fid 0xc (2000 MHz), vid 0xe
[ 52.145374] powernow-k8: 2 : fid 0xa (1800 MHz), vid 0x10
[ 52.145376] powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12
[ 52.667493] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 52.667497] apm: overridden by ACPI.
[ 52.891524] ppdev: user-space parallel port driver
[ 52.997963] audit(1236805580.180:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5260 profile="/usr/sbin/cupsd" namespace="default"
[ 117.221203] Marking TSC unstable due to: cpufreq changes.
[ 117.229753] Time: hpet clocksource has been installed.
[ 117.761582] Clocksource tsc unstable (delta = -272746870 ns)
[ 119.663278] r8169: eth0: link up
[ 119.663292] r8169: eth0: link up
[ 120.456033] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 18 (level, low) -> IRQ 16
[ 55.623134] NET: Registered protocol family 17
[ 56.061171] [fglrx] GART Table is not in FRAME_BUFFER range
[ 56.061180] [fglrx] Reserve Block - 0 offset = 0Xfffc000 length = 0X4000
[ 56.061182] [fglrx] Reserve Block - 1 offset = 0X0 length = 0X1000000
[ 56.238657] [fglrx] interrupt source ff000034 successfully enabled
[ 56.238662] [fglrx] enable ID = 0x00000006
[ 56.238946] [fglrx] Receive enable interrupt message with irqEnableMask: ff000034
[ 56.239136] [fglrx] interrupt source a0000400 successfully enabled
[ 56.239139] [fglrx] enable ID = 0x00000007
[ 56.239348] [fglrx] Receive enable interrupt message with irqEnableMask: a0000400
[ 56.239529] [fglrx] interrupt source 10000000 successfully enabled
[ 56.239531] [fglrx] enable ID = 0x00000008
[ 56.239740] [fglrx] Receive enable interrupt message with irqEnableMask: 10000000
[ 126.545168] NET: Registered protocol family 10
[ 126.545898] lo: Disabled Privacy Extensions
[ 59.871401] hda-intel: Invalid position buffer, using LPIB read method instead.
[ 139.478480] eth0: no IPv6 routers present
tapis@TAPIS:~$ 80] eth0: no IPv6 routers present
bash: 80]: command not found
tapis@TAPIS:~$ tapis@TAPIS:~$ dmesg
bash: tapis@TAPIS:~$: command not found
tapis@TAPIS:~$ 80] eth0: no IPv6 routers present
bash: 80]: command not found
tapis@TAPIS:~$ tapis@TAPIS:~$ dmesg
bash: tapis@TAPIS:~$: command not found
tapis@TAPIS:~$ 80] eth0: no IPv6 routers present
bash: 80]: command not found
tapis@TAPIS:~$ tapis@TAPIS:~$ dmesg
bash: tapis@TAPIS:~$: command not found
tapis@TAPIS:~$ 80] eth0: no IPv6 routers present
bash: 80]: command not found
tapis@TAPIS:~$ tapis@TAPIS:~$ dmesg
bash: tapis@TAPIS:~$: command not found
tapis@TAPIS:~$


[logari81]

Η καρτα τηλεορασης παντως φαινεται να εχει αναγνωρισθει κανονικα. Ισως βοηθησει και το να απενεργοποιήσεις και τα εφφε.

[Parakoudos]

για να υποστηριξει xvideo το οποιο απαιτειται απο το tvtime χρειαζεται τους κλειστους οδηγους που μπορεις να βρεις στο System--Administration--Hardware Drivers

θα μπορούσες να μου το εξηγησεις λιγακι?
ειχα εγκαταστησει το driver ...

Ισως βοηθησει και το να απενεργοποιήσεις και τα εφφε.

????

[logari81]

ναι το ειδα τωρα οτι τους εγκατεστησες, για τα εφφε δες αυτο:

απενεργοποιησε τα εφφε με Alt+F2 και μετα

Κώδικας: Επιλογή όλων

metacity --replace

και δες αν εξακολουθει το προβλήμα. Για να τα ξαναενεργοποιησεις πατας Alt+F2 και δινεις

Κώδικας: Επιλογή όλων

compiz

[Parakoudos]

Πως σου φαινεται αυτο?

tapis@TAPIS:~$ compiz
Checking for Xgl: not present.
Detected PCI ID for VGA: 01:05.0 0300: 1002:9610 (prog-if 00 [VGA controller])
Checking for texture_from_pixmap: not present.
Trying again with indirect rendering:
Checking for texture_from_pixmap: present.
Checking for non power of two support: present.
Checking for Composite extension: present.
Comparing resolution (1360x768) to maximum 3D texture size (8192): Passed.
Checking for nVidia: not present.
Checking for FBConfig: present.
Checking for Xgl: not present.
/usr/bin/compiz.real (video) - Warn: No 8 bit GLX pixmap format, disabling YV12 image format
GConf backend: There is an unsupported value at path /apps/compiz/plugins/scale/allscreens/options/initiate_edge. Settings from this path won't be read. Try to remove that value so that operation can continue properly.

[Parakoudos]

Warn: No 8 bit GLX pixmap format, disabling YV12 image format

μήπως αυτό φταίει που δεν δουλεύει το tvtime?
χωρίς βεβαι να ξέρω τι σημαίνει το GLX pixmap όπως ουτε το YV12 image...
θέλει κανείς να μοιραστει τις γνώσεις του μαζί μου.....

[logari81]

τρεξε

Κώδικας: Επιλογή όλων

metacity --replace

στο παράθυρο του Alt+F2

και μετα τρεξε

Κώδικας: Επιλογή όλων

tvtime

στο τερματικο και πες τι βγαζει.

[Parakoudos]

Κώδικας: Επιλογή όλων

tapis@TAPIS:~$ tvtime
Running tvtime 1.0.2.
Reading configuration from /etc/tvtime/tvtime.xml
Reading configuration from /home/tapis/.tvtime/tvtime.xml
xvoutput: No XVIDEO port found which supports YUY2 images.

*** tvtime requires hardware YUY2 overlay support from your video card
*** driver. If you are using an older NVIDIA card (TNT2), then
*** this capability is only available with their binary drivers.
*** For some ATI cards, this feature may be found in the experimental
*** GATOS drivers: http://gatos.souceforge.net/
*** If unsure, please check with your distribution to see if your
*** X driver supports hardware overlay surfaces.

tapis@TAPIS:~$


Σε ευχαριστώ πολύ Logari που με βοηθάς...