pinnacle pctv hybrid pro stick 320e

[mrds]

τα εφε ολα κλειστα και καμμια τυχη γενικως.το kaffeine βρισκει οπως σου ειπα 2-3 ψηφιακα αλλα δεν τα παιζει.επισης μου βγαζει ενα μηνυμα "κατι...info socket" :/.ολα τα αλλα απλα δεν παιζουν.λογικα φταιει η καρτα.
η εντολη dmesg βγαζει ενα τεραστιο κειμενο το οποιο δεν φαινεται ολοκληρο.υπαρχει καποιος τροπος να το δω ολοκληρο για να το δεις και εσυ.

[logari81]

δωσε το αποτελεσμα του dmesg, κι επισης ξεκινησε τα διαφορα προγραμματα που δεν παιζουν απο κονσολα για να μας πεις τι σφαλμα βγαζουν.

[mrds]

Κώδικας: Επιλογή όλων

[ 0.436393] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.436520] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.436648] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.436775] ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
[ 0.436900] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.437028] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.437079] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 98, should be 8F [20080609]
[ 0.437079] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.437079] pnp: PnP ACPI init
[ 0.437079] ACPI: bus type pnp registered
[ 0.440693] pnp 00:07: mem resource (0xfec00000-0xfec00fff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling
[ 0.440693] pnp 00:07: mem resource (0xfee00000-0xfee00fff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling
[ 0.440693] pnp 00:08: mem resource (0xffb80000-0xffbfffff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling
[ 0.440693] pnp 00:08: mem resource (0xfff00000-0xffffffff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling
[ 0.441094] pnp 00:0b: mem resource (0xe0000000-0xefffffff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling
[ 0.441094] pnp 00:0c: mem resource (0xfec00000-0xffffffff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling
[ 0.441094] pnp: PnP ACPI: found 13 devices
[ 0.441094] ACPI: ACPI bus type pnp unregistered
[ 0.441094] PCI: Using ACPI for IRQ routing
[ 0.441094] pci 0000:00:00.0: BAR 3: can't allocate resource
[ 0.460036] NET: Registered protocol family 8
[ 0.460037] NET: Registered protocol family 20
[ 0.460058] NetLabel: Initializing
[ 0.460059] NetLabel: domain hash size = 128
[ 0.460060] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.460071] NetLabel: unlabeled traffic allowed by default
[ 0.460195] PCI-DMA: Disabling AGP.
[ 0.460290] PCI-DMA: aperture base @ 20000000 size 65536 KB
[ 0.460290] PCI-DMA: using GART IOMMU.
[ 0.460290] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 0.460550] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.460556] hpet0: 4 32-bit timers, 14318180 Hz
[ 0.463460] tracer: 1286 pages allocated for 65536 entries of 80 bytes
[ 0.463462] actual entries 65586
[ 0.463550] AppArmor: AppArmor Filesystem Enabled
[ 0.463571] ACPI: RTC can wake from S4
[ 0.464043] Switched to high resolution mode on CPU 0
[ 0.464169] Switched to high resolution mode on CPU 1
[ 0.476048] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[ 0.476050] system 00:08: ioport range 0x40b-0x40b has been reserved
[ 0.476053] system 00:08: ioport range 0x4d6-0x4d6 has been reserved
[ 0.476055] system 00:08: ioport range 0xc00-0xc01 has been reserved
[ 0.476056] system 00:08: ioport range 0xc14-0xc14 has been reserved
[ 0.476058] system 00:08: ioport range 0xc50-0xc51 has been reserved
[ 0.476060] system 00:08: ioport range 0xc52-0xc52 has been reserved
[ 0.476062] system 00:08: ioport range 0xc6c-0xc6c has been reserved
[ 0.476064] system 00:08: ioport range 0xc6f-0xc6f has been reserved
[ 0.476066] system 00:08: ioport range 0xcd0-0xcd1 has been reserved
[ 0.476068] system 00:08: ioport range 0xcd2-0xcd3 has been reserved
[ 0.476070] system 00:08: ioport range 0xcd4-0xcd5 has been reserved
[ 0.476072] system 00:08: ioport range 0xcd6-0xcd7 has been reserved
[ 0.476074] system 00:08: ioport range 0xcd8-0xcdf has been reserved
[ 0.476076] system 00:08: ioport range 0x800-0x89f has been reserved
[ 0.476078] system 00:08: ioport range 0xb10-0xb1f has been reserved
[ 0.476080] system 00:08: ioport range 0x900-0x90f has been reserved
[ 0.476082] system 00:08: ioport range 0x910-0x91f has been reserved
[ 0.476085] system 00:08: ioport range 0xfe00-0xfefe has been reserved
[ 0.476090] system 00:0a: ioport range 0xe00-0xe0f has been reserved
[ 0.476092] system 00:0a: ioport range 0xe80-0xe8f has been reserved
[ 0.476094] system 00:0a: ioport range 0xf40-0xf4f has been reserved
[ 0.476099] system 00:0a: ioport range 0xa30-0xa3f has been reserved
[ 0.476106] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[ 0.476108] system 00:0c: iomem range 0xc0000-0xcffff has been reserved
[ 0.476110] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
[ 0.476112] system 00:0c: iomem range 0x100000-0xcfffffff could not be reserved
[ 0.481389] pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
[ 0.481391] pci 0000:00:02.0: IO window: 0x9000-0x9fff
[ 0.481395] pci 0000:00:02.0: MEM window: 0xfe600000-0xfe6fffff
[ 0.481398] pci 0000:00:02.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
[ 0.481402] pci 0000:00:04.0: PCI bridge, secondary bus 0000:02
[ 0.481404] pci 0000:00:04.0: IO window: 0xa000-0xbfff
[ 0.481407] pci 0000:00:04.0: MEM window: 0xfe700000-0xfe7fffff
[ 0.481409] pci 0000:00:04.0: PREFETCH window: disabled
[ 0.481413] pci 0000:00:06.0: PCI bridge, secondary bus 0000:03
[ 0.481415] pci 0000:00:06.0: IO window: 0xc000-0xcfff
[ 0.481418] pci 0000:00:06.0: MEM window: 0xfe800000-0xfe8fffff
[ 0.481420] pci 0000:00:06.0: PREFETCH window: disabled
[ 0.481424] pci 0000:00:07.0: PCI bridge, secondary bus 0000:04
[ 0.481426] pci 0000:00:07.0: IO window: 0xd000-0xefff
[ 0.481429] pci 0000:00:07.0: MEM window: 0xfe900000-0xfe9fffff
[ 0.481431] pci 0000:00:07.0: PREFETCH window: disabled
[ 0.481435] pci 0000:00:09.0: PCI bridge, secondary bus 0000:05
[ 0.481436] pci 0000:00:09.0: IO window: disabled
[ 0.481439] pci 0000:00:09.0: MEM window: 0xfea00000-0xfeafffff
[ 0.481441] pci 0000:00:09.0: PREFETCH window: disabled
[ 0.481445] pci 0000:00:14.4: PCI bridge, secondary bus 0000:06
[ 0.481446] pci 0000:00:14.4: IO window: disabled
[ 0.481452] pci 0000:00:14.4: MEM window: 0xfeb00000-0xfebfffff
[ 0.481456] pci 0000:00:14.4: PREFETCH window: disabled
[ 0.481469] pci 0000:00:02.0: setting latency timer to 64
[ 0.481474] pci 0000:00:04.0: setting latency timer to 64
[ 0.481480] pci 0000:00:06.0: setting latency timer to 64
[ 0.481485] pci 0000:00:07.0: setting latency timer to 64
[ 0.481491] pci 0000:00:09.0: setting latency timer to 64
[ 0.481498] bus: 00 index 0 io port: [0, ffff]
[ 0.481499] bus: 00 index 1 mmio: [0, ffffffffffffffff]
[ 0.481501] bus: 01 index 0 io port: [9000, 9fff]
[ 0.481502] bus: 01 index 1 mmio: [fe600000, fe6fffff]
[ 0.481504] bus: 01 index 2 mmio: [d0000000, dfffffff]
[ 0.481505] bus: 01 index 3 mmio: [0, 0]
[ 0.481506] bus: 02 index 0 io port: [a000, bfff]
[ 0.481508] bus: 02 index 1 mmio: [fe700000, fe7fffff]
[ 0.481509] bus: 02 index 2 mmio: [0, 0]
[ 0.481510] bus: 02 index 3 mmio: [0, 0]
[ 0.481512] bus: 03 index 0 io port: [c000, cfff]
[ 0.481513] bus: 03 index 1 mmio: [fe800000, fe8fffff]
[ 0.481515] bus: 03 index 2 mmio: [0, 0]
[ 0.481516] bus: 03 index 3 mmio: [0, 0]
[ 0.481517] bus: 04 index 0 io port: [d000, efff]
[ 0.481519] bus: 04 index 1 mmio: [fe900000, fe9fffff]
[ 0.481520] bus: 04 index 2 mmio: [0, 0]
[ 0.481521] bus: 04 index 3 mmio: [0, 0]
[ 0.481522] bus: 05 index 0 mmio: [0, 0]
[ 0.481524] bus: 05 index 1 mmio: [fea00000, feafffff]
[ 0.481525] bus: 05 index 2 mmio: [0, 0]
[ 0.481526] bus: 05 index 3 mmio: [0, 0]
[ 0.481527] bus: 06 index 0 mmio: [0, 0]
[ 0.481529] bus: 06 index 1 mmio: [feb00000, febfffff]
[ 0.481530] bus: 06 index 2 mmio: [0, 0]
[ 0.481532] bus: 06 index 3 io port: [0, ffff]
[ 0.481533] bus: 06 index 4 mmio: [0, ffffffffffffffff]
[ 0.481543] NET: Registered protocol family 2
[ 0.520124] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.521187] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 0.524738] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.525185] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.525187] TCP reno registered
[ 0.536098] NET: Registered protocol family 1
[ 0.536184] checking if image is initramfs... it is
[ 1.067177] Freeing initrd memory: 8468k freed
[ 1.071630] audit: initializing netlink socket (disabled)
[ 1.071640] type=2000 audit(1235504845.068:1): initialized
[ 1.075955] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.078473] VFS: Disk quotas dquot_6.5.1
[ 1.078551] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.078649] msgmni has been set to 7920
[ 1.078750] io scheduler noop registered
[ 1.078752] io scheduler anticipatory registered
[ 1.078753] io scheduler deadline registered
[ 1.078878] io scheduler cfq registered (default)
[ 1.252066] pci 0000:01:00.0: Boot video device
[ 1.252207] pcieport-driver 0000:00:02.0: setting latency timer to 64
[ 1.252232] pcieport-driver 0000:00:02.0: found MSI capability
[ 1.252259] pci_express 0000:00:02.0:pcie00: allocate port service
[ 1.252356] pcieport-driver 0000:00:04.0: setting latency timer to 64
[ 1.252381] pcieport-driver 0000:00:04.0: found MSI capability
[ 1.252405] pci_express 0000:00:04.0:pcie00: allocate port service
[ 1.252491] pcieport-driver 0000:00:06.0: setting latency timer to 64
[ 1.252515] pcieport-driver 0000:00:06.0: found MSI capability
[ 1.252539] pci_express 0000:00:06.0:pcie00: allocate port service
[ 1.252624] pcieport-driver 0000:00:07.0: setting latency timer to 64
[ 1.252648] pcieport-driver 0000:00:07.0: found MSI capability
[ 1.252672] pci_express 0000:00:07.0:pcie00: allocate port service
[ 1.252756] pcieport-driver 0000:00:09.0: setting latency timer to 64
[ 1.252781] pcieport-driver 0000:00:09.0: found MSI capability
[ 1.252804] pci_express 0000:00:09.0:pcie00: allocate port service
[ 1.287153] hpet_resources: 0xfed00000 is busy
[ 1.287223] Linux agpgart interface v0.103
[ 1.287226] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 1.287386] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.287999] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.289896] brd: module loaded
[ 1.289962] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 1.290163] PNP: No PS/2 controller found. Probing ports directly.
[ 1.290538] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.290542] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.304422] mice: PS/2 mouse device common for all mice
[ 1.304552] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 1.304578] rtc0: alarms up to one month, y3k, hpet irqs
[ 1.304625] cpuidle: using governor ladder
[ 1.304626] cpuidle: using governor menu
[ 1.304908] TCP cubic registered
[ 1.305107] registered taskstats version 1
[ 1.305237] Magic number: 13:31:800
[ 1.305294] tty ptyr8: hash matches
[ 1.305353] rtc_cmos 00:02: setting system clock to 2009-02-24 19:47:26 UTC (1235504846)
[ 1.305356] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.305357] EDD information not available.
[ 1.305384] Freeing unused kernel memory: 540k freed
[ 1.305574] Write protecting the kernel read-only data: 4352k
[ 1.411622] fuse init (API version 7.9)
[ 1.504101] ACPI: duty_cycle spans bit 4
[ 1.504160] processor ACPI0007:00: registered as cooling_device0
[ 1.504211] processor ACPI0007:01: registered as cooling_device1
[ 1.681601] No dock devices found.
[ 1.690728] SCSI subsystem initialized
[ 1.702075] libata version 3.00 loaded.
[ 1.709846] ahci 0000:00:12.0: version 3.0
[ 1.709865] ahci 0000:00:12.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 1.709885] ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
[ 1.709982] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 1.709984] ahci 0000:00:12.0: flags: ncq sntf ilck led clo pmp pio
[ 1.710302] scsi0 : ahci
[ 1.715702] scsi1 : ahci
[ 1.715926] scsi2 : ahci
[ 1.720732] scsi3 : ahci
[ 1.720825] ata1: SATA max UDMA/133 abar m1024@0xfe5ff800 port 0xfe5ff900 irq 22
[ 1.720829] ata2: SATA max UDMA/133 abar m1024@0xfe5ff800 port 0xfe5ff980 irq 22
[ 1.720832] ata3: SATA max UDMA/133 abar m1024@0xfe5ff800 port 0xfe5ffa00 irq 22
[ 1.720835] ata4: SATA max UDMA/133 abar m1024@0xfe5ff800 port 0xfe5ffa80 irq 22
[ 1.855859] usbcore: registered new interface driver usbfs
[ 1.855879] usbcore: registered new interface driver hub
[ 1.855910] usbcore: registered new device driver usb
[ 1.868949] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.902720] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 2.216027] ata1: softreset failed (device not ready)
[ 2.216031] ata1: failed due to HW bug, retry pmp=0
[ 2.376033] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.376809] ata1.00: ATA-8: WDC WD4000AAKS-00A7B0, 01.03B01, max UDMA/133
[ 2.376812] ata1.00: 781422768 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 2.376820] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 2.377681] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 2.377683] ata1.00: configured for UDMA/133
[ 2.860019] ata2: softreset failed (device not ready)
[ 2.860022] ata2: failed due to HW bug, retry pmp=0
[ 3.024030] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.024552] ata2.00: ATA-7: WDC WD2500KS-00MJB0, 02.01C03, max UDMA/133
[ 3.024554] ata2.00: 488397168 sectors, multi 16: LBA48
[ 3.024561] ata2.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 3.025178] ata2.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 3.025180] ata2.00: configured for UDMA/133
[ 3.508516] ata3: softreset failed (device not ready)
[ 3.508519] ata3: failed due to HW bug, retry pmp=0
[ 3.672028] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3.672772] ata3.00: ATAPI: TSSTcorp CDDVDW SH-S223F, SB01, max UDMA/100, ATAPI AN
[ 3.672779] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 3.673862] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 3.673864] ata3.00: configured for UDMA/100
[ 3.992032] ata4: SATA link down (SStatus 0 SControl 300)
[ 3.992109] scsi 0:0:0:0: Direct-Access ATA WDC WD4000AAKS-0 01.0 PQ: 0 ANSI: 5
[ 3.993303] scsi 1:0:0:0: Direct-Access ATA WDC WD2500KS-00M 02.0 PQ: 0 ANSI: 5
[ 3.994060] scsi 2:0:0:0: CD-ROM TSSTcorp CDDVDW SH-S223F SB01 PQ: 0 ANSI: 5
[ 3.994580] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.994592] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 3.994626] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[ 3.994652] ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe5fe000
[ 4.052100] usb usb1: configuration #1 chosen from 1 choice
[ 4.052124] hub 1-0:1.0: USB hub found
[ 4.052133] hub 1-0:1.0: 2 ports detected
[ 4.152163] ohci_hcd 0000:00:13.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 4.152174] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 4.152195] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
[ 4.152213] ohci_hcd 0000:00:13.1: irq 17, io mem 0xfe5fd000
[ 4.212582] usb usb2: configuration #1 chosen from 1 choice
[ 4.212605] hub 2-0:1.0: USB hub found
[ 4.212614] hub 2-0:1.0: 2 ports detected
[ 4.420648] ohci_hcd 0000:00:13.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 4.420659] ohci_hcd 0000:00:13.2: OHCI Host Controller
[ 4.420680] ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
[ 4.420699] ohci_hcd 0000:00:13.2: irq 18, io mem 0xfe5fc000
[ 4.480448] usb usb3: configuration #1 chosen from 1 choice
[ 4.480472] hub 3-0:1.0: USB hub found
[ 4.480480] hub 3-0:1.0: 2 ports detected
[ 4.556018] usb 2-1: new low speed USB device using ohci_hcd and address 2
[ 4.684145] ohci_hcd 0000:00:13.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 4.684155] ohci_hcd 0000:00:13.3: OHCI Host Controller
[ 4.684179] ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 4
[ 4.684191] ohci_hcd 0000:00:13.3: irq 17, io mem 0xfe5fb000
[ 4.731014] usb 2-1: configuration #1 chosen from 1 choice
[ 4.744996] usb usb4: configuration #1 chosen from 1 choice
[ 4.745459] hub 4-0:1.0: USB hub found
[ 4.745468] hub 4-0:1.0: 2 ports detected
[ 4.868016] usb 3-2: new low speed USB device using ohci_hcd and address 2
[ 4.953530] ohci_hcd 0000:00:13.4: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 4.953538] ohci_hcd 0000:00:13.4: OHCI Host Controller
[ 4.954018] ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 5
[ 4.954032] ohci_hcd 0000:00:13.4: irq 18, io mem 0xfe5fa000
[ 5.013030] usb usb5: configuration #1 chosen from 1 choice
[ 5.013520] hub 5-0:1.0: USB hub found
[ 5.013528] hub 5-0:1.0: 2 ports detected
[ 5.038572] usb 3-2: configuration #1 chosen from 1 choice
[ 5.176017] usb 4-1: new full speed USB device using ohci_hcd and address 2
[ 5.220153] ehci_hcd 0000:00:13.5: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 5.220162] ehci_hcd 0000:00:13.5: EHCI Host Controller
[ 5.220180] ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 6
[ 5.220202] ehci_hcd 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround
[ 5.220223] ehci_hcd 0000:00:13.5: debug port 1
[ 5.220235] ehci_hcd 0000:00:13.5: irq 19, io mem 0xfe5ff000
[ 5.324514] ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 5.324588] usb usb6: configuration #1 chosen from 1 choice
[ 5.324607] hub 6-0:1.0: USB hub found
[ 5.324613] hub 6-0:1.0: 10 ports detected
[ 5.533261] pata_acpi 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 5.533292] pata_acpi 0000:00:14.1: setting latency timer to 64
[ 5.535015] sky2 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 5.535027] sky2 0000:03:00.0: setting latency timer to 64
[ 5.535046] sky2 0000:03:00.0: v1.22 addr 0xfe8fc000 irq 18 Yukon-2 EC Ultra rev 3
[ 5.535505] sky2 eth0: addr 00:1e:8c:c3:7c:18
[ 5.535867] pata_acpi 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 5.535895] pata_acpi 0000:02:00.0: setting latency timer to 64
[ 5.535906] pata_acpi 0000:02:00.0: PCI INT A disabled
[ 5.536054] ohci1394 0000:06:08.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 5.536153] pata_acpi 0000:04:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 5.536171] pata_acpi 0000:04:00.0: setting latency timer to 64
[ 5.536180] pata_acpi 0000:04:00.0: PCI INT A disabled
[ 5.587699] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[22] MMIO=[febff000-febff7ff] Max Packet=[2048] IR/IT contexts=[8/8]
[ 5.596937] scsi 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.596966] scsi 1:0:0:0: Attached scsi generic sg1 type 0
[ 5.596997] scsi 2:0:0:0: Attached scsi generic sg2 type 5
[ 5.605283] pata_marvell 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 5.605316] pata_marvell 0000:02:00.0: setting latency timer to 64
[ 5.605425] scsi4 : pata_marvell
[ 5.605478] scsi5 : pata_marvell
[ 5.605505] ata5: PATA max UDMA/100 cmd 0xb800 ctl 0xb400 bmdma 0xa400 irq 16
[ 5.605507] ata6: PATA max UDMA/133 cmd 0xb000 ctl 0xa800 bmdma 0xa408 irq 16
[ 5.625544] Driver 'sr' needs updating - please use bus_type methods
[ 5.628329] Driver 'sd' needs updating - please use bus_type methods
[ 5.628412] sd 0:0:0:0: [sda] 781422768 512-byte hardware sectors (400088 MB)
[ 5.628444] sd 0:0:0:0: [sda] Write Protect is off
[ 5.628446] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.628466] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.628544] sd 0:0:0:0: [sda] 781422768 512-byte hardware sectors (400088 MB)
[ 5.628554] sd 0:0:0:0: [sda] Write Protect is off
[ 5.628556] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.628574] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.628577] sda:sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.630816] Uniform CD-ROM driver Revision: 3.20
[ 5.630872] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 5.642898] sda1 sda2 < sda5 sda6 >
[ 5.674655] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.674708] sd 1:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[ 5.674720] sd 1:0:0:0: [sdb] Write Protect is off
[ 5.674722] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 5.674742] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.674781] sd 1:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[ 5.674792] sd 1:0:0:0: [sdb] Write Protect is off
[ 5.674794] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 5.674814] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.674816] sdb: sdb1
[ 5.688379] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 5.720514] usb 4-1: device not accepting address 2, error -62
[ 5.776022] hub 4-0:1.0: unable to enumerate USB device on port 1
[ 5.935595] pata_marvell 0000:04:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 5.935621] pata_marvell 0000:04:00.0: setting latency timer to 64
[ 5.936828] scsi6 : pata_marvell
[ 5.937714] scsi7 : pata_marvell
[ 5.937751] ata7: PATA max UDMA/100 cmd 0xe800 ctl 0xe400 bmdma 0xd400 irq 19
[ 5.937753] ata8: PATA max UDMA/133 cmd 0xe000 ctl 0xd800 bmdma 0xd408 irq 19
[ 6.160053] usbcore: registered new interface driver hiddev
[ 6.160517] usb 3-2: USB disconnect, address 2
[ 6.274743] scsi8 : pata_atiixp
[ 6.274798] scsi9 : pata_atiixp
[ 6.276188] ata9: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
[ 6.276190] ata10: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
[ 6.288555] usb 2-1: USB disconnect, address 2
[ 6.756018] usb 6-8: new high speed USB device using ehci_hcd and address 5
[ 6.864162] ieee1394: Host added: ID:BUS[0-00:1023] GUID[001e8c0001082050]
[ 6.891939] usb 6-8: configuration #1 chosen from 1 choice
[ 7.004021] usb 6-9: new high speed USB device using ehci_hcd and address 6
[ 7.137107] usb 6-9: configuration #1 chosen from 1 choice
[ 7.137456] usbcore: registered new interface driver usbhid
[ 7.137459] usbhid: v2.6:USB HID core driver
[ 7.400019] usb 2-1: new low speed USB device using ohci_hcd and address 3
[ 7.573648] usb 2-1: configuration #1 chosen from 1 choice
[ 7.629662] hiddev96hidraw0: USB HID v1.10 Device [CPS UPS VALUE] on usb-0000:00:13.1-1
[ 7.892018] usb 3-2: new low speed USB device using ohci_hcd and address 3
[ 8.061558] usb 3-2: configuration #1 chosen from 1 choice
[ 8.068680] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:13.2/usb3/3-2/3-2:1.0/input/input1
[ 8.096565] input,hidraw1: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:13.2-2
[ 8.103049] Fixing up Logitech keyboard report descriptor
[ 8.103792] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:13.2/usb3/3-2/3-2:1.1/input/input2
[ 8.148616] input,hiddev97,hidraw2: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:13.2-2
[ 8.412018] usb 4-1: new full speed USB device using ohci_hcd and address 4
[ 8.586627] usb 4-1: configuration #1 chosen from 1 choice
[ 8.588789] usbcore: registered new interface driver libusual
[ 8.592876] Initializing USB Mass Storage driver...
[ 8.592953] scsi10 : SCSI emulation for USB Mass Storage devices
[ 8.593028] usbcore: registered new interface driver usb-storage
[ 8.593031] USB Mass Storage support registered.
[ 8.593137] usb-storage: device found at 6
[ 8.593138] usb-storage: waiting for device to settle before scanning
[ 8.635253] PM: Starting manual resume from disk
[ 8.635255] PM: Resume from partition 8:6
[ 8.635257] PM: Checking hibernation image.
[ 8.635384] PM: Resume from disk failed.
[ 8.649801] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 8.649804] EXT3-fs: write access will be enabled during recovery.
[ 10.748121] kjournald starting. Commit interval 5 seconds
[ 10.748140] EXT3-fs: sda5: orphan cleanup on readonly fs
[ 10.748145] ext3_orphan_cleanup: deleting unreferenced inode 4374886
[ 10.748178] EXT3-fs: sda5: 1 orphan inode deleted
[ 10.748179] EXT3-fs: recovery complete.
[ 10.749876] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.592171] usb-storage: device scan complete
[ 13.592636] scsi 10:0:0:0: Direct-Access WD 3200AAJ External 1.06 PQ: 0 ANSI: 0
[ 13.593501] sd 10:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
[ 13.594250] sd 10:0:0:0: [sdc] Write Protect is off
[ 13.594252] sd 10:0:0:0: [sdc] Mode Sense: 00 00 00 00
[ 13.594254] sd 10:0:0:0: [sdc] Assuming drive cache: write through
[ 13.594876] sd 10:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
[ 13.595627] sd 10:0:0:0: [sdc] Write Protect is off
[ 13.595629] sd 10:0:0:0: [sdc] Mode Sense: 00 00 00 00
[ 13.595630] sd 10:0:0:0: [sdc] Assuming drive cache: write through
[ 13.595633] sdc:<6>usb 2-1: USB disconnect, address 3
[ 16.255735] udevd version 124 started
[ 16.461538] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 16.464154] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 16.520533] usb 2-1: new low speed USB device using ohci_hcd and address 4
[ 16.532173] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 16.556025] ACPI: Power Button (FF) [PWRF]
[ 16.556140] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
[ 16.588029] ACPI: Power Button (CM) [PWRB]
[ 16.600397] ACPI: WMI: Mapper loaded
[ 16.692778] usb 2-1: configuration #1 chosen from 1 choice
[ 16.747760] hiddev96hidraw0: USB HID v1.10 Device [CPS UPS VALUE] on usb-0000:00:13.1-1
[ 16.930962] ath_hal: module license 'Proprietary' taints kernel.
[ 16.932014] ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[ 16.946986] wlan: 0.9.4
[ 16.966329] ath_pci: 0.9.4
[ 16.967305] ath_pci 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 16.967314] ath_pci 0000:05:00.0: setting latency timer to 64
[ 16.991675] wifi%d: unable to attach hardware: 'Hardware revision not supported' (HAL status 13)
[ 16.991688] ath_pci 0000:05:00.0: PCI INT A disabled
[ 17.085242] [fglrx] Maximum main memory to use for locked dma buffers: 3798 MBytes.
[ 17.085530] [fglrx] vendor: 1002 device: 9598 count: 1
[ 17.086002] [fglrx] ioport: bar 4, base 0x9000, size: 0x100
[ 17.086014] pci 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 17.086019] pci 0000:01:00.0: setting latency timer to 64
[ 17.086542] [fglrx] PAT is enabled successfully!
[ 17.086575] [fglrx] module loaded - fglrx 8.54.3 [Oct 10 2008] with 1 minors
[ 17.342048] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 17.360475] usblp0: USB Bidirectional printer dev 4 if 0 alt 0 proto 2 vid 0x03F0 pid 0x6204
[ 17.360517] usbcore: registered new interface driver usblp
[ 17.368025] hda_codec: Unknown model for AD1988, trying auto-probe from BIOS...
[ 17.491994] Linux video capture interface: v2.00
[ 17.586876] em28xx v4l2 driver version 0.0.1 loaded
[ 17.589387] em28xx: new video device (eb1a:2881): interface 0, class 255
[ 17.589389] em28xx: device is attached to a USB 2.0 bus
[ 17.589395] em28xx #0: Alternate settings: 8
[ 17.589397] em28xx #0: Alternate setting 0, max size= 0
[ 17.589398] em28xx #0: Alternate setting 1, max size= 0
[ 17.589399] em28xx #0: Alternate setting 2, max size= 1448
[ 17.589401] em28xx #0: Alternate setting 3, max size= 2048
[ 17.589402] em28xx #0: Alternate setting 4, max size= 2304
[ 17.589404] em28xx #0: Alternate setting 5, max size= 2580
[ 17.589405] em28xx #0: Alternate setting 6, max size= 2892
[ 17.589407] em28xx #0: Alternate setting 7, max size= 3072
[ 17.628755] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 17.751505] HDA Intel 0000:01:00.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 17.751525] HDA Intel 0000:01:00.1: setting latency timer to 64
[ 17.751533] ACPI: I/O resource piix4_smbus [0xb00-0xb07] conflicts with ACPI region SOR1 [0xb00-0xb0f]
[ 17.751536] ACPI: Device needs an ACPI driver
[ 17.751542] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 18.065731] attach_inform: tvp5150 detected.
[ 18.128978] tvp5150 1-005c: tvp5150am1 detected.
[ 18.988125] sdc1
[ 18.992572] sd 10:0:0:0: [sdc] Attached SCSI disk
[ 18.992691] sd 10:0:0:0: Attached scsi generic sg3 type 0
[ 19.672065] successfully attached tuner
[ 19.676209] em28xx #0: V4L2 VBI device registered as /dev/vbi0
[ 19.693685] em28xx #0: V4L2 device registered as /dev/video0
[ 19.693733] input: em2880/em2870 remote control as /devices/virtual/input/input6
[ 19.744604] em28xx-input.c: remote control handler attached
[ 19.744607] em28xx #0: Found Pinnacle Hybrid Pro
[ 19.744628] audio device (eb1a:2881): interface 1, class 1
[ 19.751737] usbcore: registered new interface driver snd-usb-audio
[ 19.756766] usbcore: registered new interface driver em28xx
[ 19.780847] em2880-dvb.c: DVB Init
[ 20.101115] DVB: registering new adapter (em2880 DVB-T)
[ 20.101120] DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)...
[ 20.101440] Em28xx: Initialized (Em2880 DVB Extension) extension
[ 20.280514] lp: driver loaded but no devices found
[ 20.412379] Adding 3285252k swap on /dev/sda6. Priority:-1 extents:1 across:3285252k
[ 20.952287] EXT3 FS on sda5, internal journal
[ 21.739128] type=1505 audit(1235497666.585:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4451
[ 21.856556] type=1505 audit(1235497666.705:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4456
[ 21.856703] type=1505 audit(1235497666.705:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4456
[ 21.965272] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 22.576278] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 5600+ processors (2 cpu cores) (version 2.20.00)
[ 22.576297] powernow-k8: ACPI Processor support is required for SMP systems but is absent. Please load the ACPI Processor module before starting this driver.
[ 22.576317] powernow-k8: ACPI Processor support is required for SMP systems but is absent. Please load the ACPI Processor module before starting this driver.
[ 23.120589] usb 2-1: USB disconnect, address 4
[ 23.233303] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[ 23.533518] ppdev: user-space parallel port driver
[ 25.344946] tvp5150 1-005c: tvp5150am1 detected.
[ 25.632020] usb 2-1: new low speed USB device using ohci_hcd and address 5
[ 25.812431] Bluetooth: Core ver 2.13
[ 25.813526] NET: Registered protocol family 31
[ 25.813531] Bluetooth: HCI device and connection manager initialized
[ 25.813534] Bluetooth: HCI socket layer initialized
[ 25.817197] usb 2-1: configuration #1 chosen from 1 choice
[ 25.850193] Bluetooth: L2CAP ver 2.11
[ 25.850198] Bluetooth: L2CAP socket layer initialized
[ 25.860561] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 25.860566] Bluetooth: BNEP filters: protocol multicast
[ 25.875696] Bridge firewalling registered
[ 25.877851] hiddev96hidraw0: USB HID v1.10 Device [CPS UPS VALUE] on usb-0000:00:13.1-1
[ 25.888140] Bluetooth: SCO (Voice Link) ver 0.6
[ 25.888145] Bluetooth: SCO socket layer initialized
[ 25.976516] Bluetooth: RFCOMM socket layer initialized
[ 25.976755] Bluetooth: RFCOMM TTY layer initialized
[ 25.976759] Bluetooth: RFCOMM ver 1.10
[ 28.911846] [fglrx] CMM init INV FB MC:0xd0000000, length:0x10000000
[ 28.911855] [fglrx] Reserved FB block: Shared offset:0, size:1000000
[ 28.911857] [fglrx] Reserved FB block: Unshared offset:ff77000, size:88000
[ 30.088789] sky2 eth0: enabling interface
[ 31.942461] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control rx
[ 32.002533] NET: Registered protocol family 17
[ 33.169888] hda-intel: Invalid position buffer, using LPIB read method instead.
[ 34.339504] NET: Registered protocol family 10
[ 34.340577] lo: Disabled Privacy Extensions
[ 44.532514] eth0: no IPv6 routers present
[ 52.484284] canberra-gtk-pl[6000]: segfault at 1021d1930 ip 00007f24c2edc80c sp 0000000041346bd0 error 6 in libc-2.8.90.so[7f24c2e60000+169000]
[ 78.960080] em28xx_dvb_init
[ 100.176025] em28xx_dvb_init
[ 122.349028] [fglrx] CMM init INV FB MC:0xd0000000, length:0x10000000
[ 122.349039] [fglrx] Reserved FB block: Shared offset:0, size:1000000
[ 122.349042] [fglrx] Reserved FB block: Unshared offset:ff77000, size:88000
[ 130.416665] em28xx #0: reading key failed (error=-110)

οπως ειπα στο προηγουμενο ποστ που εκανα edit δεν φαινονται καποια αρχικα αποτελεσματα.μπορω με καποιο τροπο να κανω το τερμιναλ να μη μου σβηνει γραμμες οταν τα αποτελεσματα εντολων ειναι μεγαλα? επισης δεν ξερω πως να ξεκινω προγραμματα απο το τερμιναλ :/.

[mrds]

μετα απο πραγματικη μαχη μπορεσα επιτελους να δω και να ακουσω τα ψηφιακα καναλια που πιανω (καφφεινε).το θεμα ειναι ομως να πιασω τα αναλογικα καναλια.το xawtv επαιξε τελικα τα καναλια χωρις ηχο.ας βοηθησει καποιος.