nVidia 8400M GT + HDMI problem + Brightness Problem(hotkey)

[Learner]

Το μήνυμα NVRM εξαφανίστηκε. Με τα γραφικά τι γίνεται όμως ;

Εξακολουθείς να έχεις πρόβλημα ; η ανάλυση πως είναι ;

Από ότι κατάλαβα λειτουργεί ο Vesa ;

Ναι , γι' αυτό τον θέσαμε off για να δούμε τι θα γίνει.

[pelopidass]

Το μήνυμα NVRM εξαφανίστηκε. Με τα γραφικά τι γίνεται όμως ;

Εξακολουθείς να έχεις πρόβλημα ; η ανάλυση πως είναι ;

Από ότι κατάλαβα λειτουργεί ο Vesa ;

Ναι , γι' αυτό τον θέσαμε off για να δούμε τι θα γίνει.

Aυτη τη στιγμη ειναι στο θεο η αναλυση. Βασικα εμενα στο grub ηταν quiet splash οχι splash quiet πειραζει αυτο;

[Learner]

Βασικα εμενα στο grub ηταν quiet splash οχι splash quiet πειραζει αυτο;

Καλά κάνεις και προσέχεις τις λεπτομέρειες , αλλά το συγκεκριμένο δεν πειράζει

Aυτη τη στιγμη ειναι στο θεο η αναλυση.

Αυτό είναι τώρα καλό ή κακό ; Μάλλον εννοείς μικρή ; (κακό δηλαδή).

Για δώσε το αποτέλεσμα

Κώδικας: Επιλογή όλων

cat /etc/default/grub | grep GRUB_CMDLINE_LINUX_DEFAULT

[pelopidass]

Κώδικας: Επιλογή όλων

GRUB_CMDLINE_LINUX_DEFAULT="splash quiet video=vesa:off vga=normal"

Ειναι 1024χ768 αντι για 1280x800.

[Learner]

Πέρνα και την παράμετρο nomodeset μέσα και αφαίρεσε το vga=normal , να δούμε.

Αυτή είναι μια εντολή.

Κώδικας: Επιλογή όλων

sudo sed -i 's/GRUB_CMDLINE_LINUX_DEFAULT="splash quiet video=vesa:off vga=normal"/GRUB_CMDLINE_LINUX_DEFAULT="splash quiet nomodeset video=vesa:off"/g' /etc/default/grub

αν δεν σου βγάλει κάποιο error η παραπάνω μετά τρέχεις

Κώδικας: Επιλογή όλων

sudo update-grub

Επανεκκίνηση και δίνεις πάλι τα αποτελέσματα

Κώδικας: Επιλογή όλων

dmesg | grep -ie nouveau -ie drm -ie vesa

Κώδικας: Επιλογή όλων

lspci -nnk | grep -iA2 vga

[pelopidass]

Κώδικας: Επιλογή όλων

[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-30-generic-pae root=UUID=d4000f4c-a9db-4cd9-b0fc-d39e29a75a2e ro acpi_osi=Linux splash quiet nomodeset video=vesa:off vt.handoff=7
[ 21.080763] [drm] Initialized drm 1.1.0 20060810
[ 27.127041] vesafb: mode is 640x480x32, linelength=2560, pages=0
[ 27.127046] vesafb: scrolling: redraw
[ 27.127052] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 27.129077] vesafb: framebuffer at 0xcd000000, mapped to 0xf8a80000, using 1216k, total 1216k
[ 27.130126] fbcon: VESA VGA (fb0) is primary device
[ 27.130250] fb0: VESA VGA frame buffer device

Κώδικας: Επιλογή όλων

01:00.0 VGA compatible controller [0300]: NVIDIA Corporation G86 [GeForce 8400M GT] [10de:0426] (rev a1)
Subsystem: Sony Corporation Device [104d:9005]
Kernel modules: nouveau, nvidiafb


Αυτη τη στιγμη η αναλυση ειναι 640x480....:S

Εdit: Ξανα μπηκε με 1024x768.

Απο οτι καταλαβα αλλες φορες φορτωνει τον vesa και αλλες τον nouveau. Γιατι ομως;

[Learner]

Αφαίρεσε το nomodeset. Μια δοκιμή κάναμε , αλλά δεν...

Μια εντολή είναι αυτή.

Κώδικας: Επιλογή όλων

sudo sed -i 's/GRUB_CMDLINE_LINUX_DEFAULT="splash quiet nomodeset video=vesa:off"/GRUB_CMDLINE_LINUX_DEFAULT="splash quiet video=vesa:off"/g' /etc/default/grub

μετά τρέχεις

Κώδικας: Επιλογή όλων

sudo update-grub

Απο οτι καταλαβα αλλες φορες φορτωνει τον vesa και αλλες τον nouveau. Γιατι ομως;

Ναι , αυτό είναι το βασικό πρόβλημα. Αν έμπαινε με τον nouveau συνέχεια , τότε θα το είχαμε λύσει.
Δεν ξέρω γιατί. Πιθανών bug ;

Το πρόβλημα παρουσιάζεται όταν στο dmesg εμφανίζεται αυτό το μήνυμα

Κώδικας: Επιλογή όλων

[ 18.270973] [drm] nouveau 0000:01:00.0: Unsupported chipset 0xffffffff

Σε αναζήτηση (Google) δεν βρήκα κάποιο workaround . (ακόμη)

Ίσως είναι ώρα να δοκιμάσουμε άλλο πυρήνα.

[pelopidass]

To ειδα και εγω αυτο εψαξα μπας και βρω τιποτα αλλα μπα...

Τωρα πως βαζουμε αλλο πυρηνα; Περιμενω κανα update?

[Learner]

Τωρα πως βαζουμε αλλο πυρηνα; Περιμενω κανα update?

Sorry για την καθυστέρηση , είχα ένα προβληματάκι με το Internet.

Λοιπόν , για να βάλεις τον νεότερο πυρήνα, χάρις τον medigeek που δημιούργησε ένα πρόγραμμα , η διαδικασία πλέον είναι αυτοματοποιημένη.

Ανοίγεις ένα τερματικό και τρέχεις

Κώδικας: Επιλογή όλων

sudo apt-get install python-bs4

Μετά πατάς εδώ για να κατεβάσεις ένα πακέτο. (συμπιεσμένο).

Έπειτα στο τερματικό τρέχεις

Κώδικας: Επιλογή όλων

cd Downloads
tar -xvzf medigeek-kmp-downloader-7d119ab.tar.gz
cd medigeek-kmp-downloader-7d119ab/
chmod a+x kmpd.py
./kmpd.py

με την τελευταία εντολή αρχίζει η διαδικασία. Εσύ απλά θα πατήσεις σε όλα Enter (κάποια στιγμή θα σου ζητηθεί και ο κωδικός σου) και θα περιμένεις να τελειώσει, θα βγάλει στο τέλος ένα μήνυμα

Κώδικας: Επιλογή όλων

All done! Press any key to exit

Μόλις κάνεις επανεκκίνηση , θα μπεις αυτόματα από τον νέο πυρήνα. Ελπίζω εκεί να δουλεύει.

Ενδιαφέρον θα έχουν και τα μηνύματα του dmesg

Κώδικας: Επιλογή όλων

dmesg >> dmesg.txt

Κώδικας: Επιλογή όλων

gedit dmesg.txt

και τα επικολλάς εδώ.

[pelopidass]

Κώδικας: Επιλογή όλων

[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-29-generic-pae (buildd@roseapple) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #46-Ubuntu SMP Fri Jul 27 17:25:43 UTC 2012 (Ubuntu 3.2.0-29.46-generic-pae 3.2.24)
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fed0000 (usable)
[ 0.000000] BIOS-e820: 000000007fed0000 - 000000007fee0000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007fee0000 - 000000007fee3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007fee3000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI present.
[ 0.000000] DMI: Sony Corporation VGN-FZ21M/VAIO, BIOS R1120J7 07/04/2007
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0x7fed0 max_arch_pfn = 0x1000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07FF00000 mask FFFF00000 uncachable
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] original variable MTRRs
[ 0.000000] reg 0, base: 0GB, range: 2GB, type WB
[ 0.000000] reg 1, base: 2047MB, range: 1MB, type UC
[ 0.000000] total RAM covered: 2047M
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.000000] gran_size: 64K chunk_size: 2M num_reg: 2 lose cover RAM: 0G
[ 0.000000] New variable MTRRs
[ 0.000000] reg 0, base: 0GB, range: 2GB, type WB
[ 0.000000] reg 1, base: 2047MB, range: 1MB, type UC
[ 0.000000] found SMP MP-table at [c00f8090] f8090
[ 0.000000] initial memory mapped : 0 - 02000000
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: 0000000000000000-0000000037bfe000
[ 0.000000] 0000000000 - 0000200000 page 4k
[ 0.000000] 0000200000 - 0037a00000 page 2M
[ 0.000000] 0037a00000 - 0037bfe000 page 4k
[ 0.000000] kernel direct mapping tables up to 37bfe000 @ 1ffb000-2000000
[ 0.000000] RAMDISK: 364f0000 - 37270000
[ 0.000000] ACPI: RSDP 000f8060 00024 (v02 PTLTD )
[ 0.000000] ACPI: XSDT 7fed7f39 00084 (v01 Sony VAIO 20070704 PTL 00000000)
[ 0.000000] ACPI: FACP 7fedfc04 000F4 (v03 Sony VAIO 20070704 PTL 00000001)
[ 0.000000] ACPI: DSDT 7fed9217 06979 (v02 Sony VAIO 20070704 PTL 20050624)
[ 0.000000] ACPI: FACS 7fee2fc0 00040
[ 0.000000] ACPI: APIC 7fedfcf8 00068 (v01 Sony VAIO 20070704 PTL 0000005A)
[ 0.000000] ACPI: HPET 7fedfd60 00038 (v01 Sony VAIO 20070704 PTL 0000005A)
[ 0.000000] ACPI: MCFG 7fedfd98 0003C (v01 Sony VAIO 20070704 PTL 0000005A)
[ 0.000000] ACPI: SLIC 7fedfdd4 00176 (v01 Sony VAIO 20070704 PTL 01000000)
[ 0.000000] ACPI: TMOR 7fedff4a 00026 (v01 Sony VAIO 20070704 PTL 00000003)
[ 0.000000] ACPI: APIC 7fedff70 00068 (v01 Sony VAIO 20070704 PTL 00000000)
[ 0.000000] ACPI: BOOT 7fedffd8 00028 (v01 Sony VAIO 20070704 PTL 00000001)
[ 0.000000] ACPI: SSDT 7fed90fa 0011D (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.000000] ACPI: SSDT 7fed85a5 00287 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.000000] ACPI: SSDT 7fed84f1 000B4 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.000000] ACPI: SSDT 7fed7fbd 00534 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.000000] ACPI: BIOS bug: multiple APIC/MADT found, using 0
[ 0.000000] ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 1154MB HIGHMEM available.
[ 0.000000] 891MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 37bfe000
[ 0.000000] low ram: 0 - 37bfe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x00037bfe
[ 0.000000] HighMem 0x00037bfe -> 0x0007fed0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007fed0
[ 0.000000] On node 0 totalpages: 523871
[ 0.000000] free_area_init_node: node 0, pgdat c1866a40, node_mem_map f54f0200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1752 pages used for memmap
[ 0.000000] Normal zone: 222502 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2310 pages used for memmap
[ 0.000000] HighMem zone: 293324 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000ce000
[ 0.000000] PM: Registered nosave memory: 00000000000ce000 - 00000000000d0000
[ 0.000000] PM: Registered nosave memory: 00000000000d0000 - 00000000000dc000
[ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:60000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @f7bd5000 s34240 r0 d23104 u57344
[ 0.000000] pcpu-alloc: s34240 r0 d23104 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519777
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-29-generic-pae root=UUID=d4000f4c-a9db-4cd9-b0fc-d39e29a75a2e ro acpi_osi=Linux quiet splash acpi_backlight=vendor vt.handoff=7
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 8383488 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Initializing HighMem for node 0 (00037bfe:0007fed0)
[ 0.000000] Memory: 2045764k/2095936k available (5814k kernel code, 49720k reserved, 2841k data, 740k init, 1182536k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
[ 0.000000] pkmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xf83fe000 - 0xffbfe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf7bfe000 ( 891 MB)
[ 0.000000] .init : 0xc1875000 - 0xc192e000 ( 740 kB)
[ 0.000000] .data : 0xc15adb64 - 0xc1874240 (2841 kB)
[ 0.000000] .text : 0xc1000000 - 0xc15adb64 (5814 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:2304 nr_irqs:512 16
[ 0.000000] CPU 0 irqstacks, hard=f5008000 soft=f500a000
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] vt handoff: transparent VT on vt#7
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1994.965 MHz processor.
[ 0.004002] Calibrating delay loop (skipped), value calculated using timer frequency.. 3989.93 BogoMIPS (lpj=7979860)
[ 0.004007] pid_max: default: 32768 minimum: 301
[ 0.004030] Security Framework initialized
[ 0.004047] AppArmor: AppArmor initialized
[ 0.004049] Yama: becoming mindful.
[ 0.004105] Mount-cache hash table entries: 512
[ 0.004243] Initializing cgroup subsys cpuacct
[ 0.004249] Initializing cgroup subsys memory
[ 0.004257] Initializing cgroup subsys devices
[ 0.004259] Initializing cgroup subsys freezer
[ 0.004261] Initializing cgroup subsys blkio
[ 0.004268] Initializing cgroup subsys perf_event
[ 0.004295] CPU: Physical Processor ID: 0
[ 0.004297] CPU: Processor Core ID: 0
[ 0.004301] mce: CPU supports 6 MCE banks
[ 0.004310] CPU0: Thermal monitoring enabled (TM2)
[ 0.004313] using mwait in idle threads.
[ 0.008870] ACPI: Core revision 20110623
[ 0.016031] ftrace: allocating 26545 entries in 52 pages
[ 0.020051] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.020491] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.063454] CPU0: Intel(R) Core(TM)2 Duo CPU T7250 @ 2.00GHz stepping 0d
[ 0.064003] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
[ 0.064003] PEBS disabled due to CPU errata.
[ 0.064003] ... version: 2
[ 0.064003] ... bit width: 40
[ 0.064003] ... generic registers: 2
[ 0.064003] ... value mask: 000000ffffffffff
[ 0.064003] ... max period: 000000007fffffff
[ 0.064003] ... fixed-purpose events: 3
[ 0.064003] ... event mask: 0000000700000003
[ 0.064003] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.064003] CPU 1 irqstacks, hard=f50ea000 soft=f50ec000
[ 0.064003] Booting Node 0, Processors #1 Ok.
[ 0.064003] smpboot cpu 1: start_ip = 9b000
[ 0.008000] Initializing CPU#1
[ 0.152038] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.152081] Brought up 2 CPUs
[ 0.152084] Total of 2 processors activated (7979.90 BogoMIPS).
[ 0.153435] devtmpfs: initialized
[ 0.153435] EVM: security.selinux
[ 0.153435] EVM: security.SMACK64
[ 0.153435] EVM: security.capability
[ 0.153435] PM: Registering ACPI NVS region at 7fee0000 (12288 bytes)
[ 0.153435] print_constraints: dummy:
[ 0.153435] RTC time: 0:10:33, date: 09/14/12
[ 0.153435] NET: Registered protocol family 16
[ 0.153435] Trying to unpack rootfs image as initramfs...
[ 0.153441] EISA bus registered
[ 0.153458] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.153462] ACPI: bus type pci registered
[ 0.153538] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.153541] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.153544] PCI: Using MMCONFIG for extended config space
[ 0.153546] PCI: Using configuration type 1 for base access
[ 0.156744] bio: create slab <bio-0> at 0
[ 0.156841] ACPI: Added _OSI(Module Device)
[ 0.156844] ACPI: Added _OSI(Processor Device)
[ 0.156846] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.156849] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.156852] ACPI: Added _OSI(Linux)
[ 0.158627] ACPI: EC: Look up EC in DSDT
[ 0.161726] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query honored via cmdline
[ 0.162956] ACPI: SSDT 7fed8d75 002A1 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.163394] ACPI: Dynamic OEM Table Load:
[ 0.163398] ACPI: SSDT (null) 002A1 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.163539] ACPI: SSDT 7fed882c 004B7 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.163955] ACPI: Dynamic OEM Table Load:
[ 0.163958] ACPI: SSDT (null) 004B7 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.164326] ACPI: SSDT 7fed9016 000E4 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.164760] ACPI: Dynamic OEM Table Load:
[ 0.164764] ACPI: SSDT (null) 000E4 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.164882] ACPI: SSDT 7fed8ce3 00092 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.165300] ACPI: Dynamic OEM Table Load:
[ 0.165303] ACPI: SSDT (null) 00092 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.166414] ACPI: EC: GPE storm detected, transactions will use polling mode
[ 0.364139] ACPI: Interpreter enabled
[ 0.364155] ACPI: (supports S0 S3 S4 S5)
[ 0.364183] ACPI: Using IOAPIC for interrupt routing
[ 0.412665] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 0.418089] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.418285] ACPI: No dock devices found.
[ 0.418289] HEST: Table not found.
[ 0.418295] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.418841] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.419598] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.419602] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.419605] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.419608] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff] (ignored)
[ 0.419612] pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff] (ignored)
[ 0.419615] pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff] (ignored)
[ 0.419619] pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xdfffffff] (ignored)
[ 0.419622] pci_root PNP0A08:00: host bridge window [mem 0xf0000000-0xfebfffff] (ignored)
[ 0.419636] pci 0000:00:00.0: [8086:2a00] type 0 class 0x000600
[ 0.419697] pci 0000:00:01.0: [8086:2a01] type 1 class 0x000604
[ 0.419753] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.419757] pci 0000:00:01.0: PME# disabled
[ 0.419817] pci 0000:00:1a.0: [8086:2834] type 0 class 0x000c03
[ 0.419879] pci 0000:00:1a.0: reg 20: [io 0x1800-0x181f]
[ 0.419927] pci 0000:00:1a.1: [8086:2835] type 0 class 0x000c03
[ 0.419989] pci 0000:00:1a.1: reg 20: [io 0x1820-0x183f]
[ 0.420063] pci 0000:00:1a.7: [8086:283a] type 0 class 0x000c03
[ 0.420090] pci 0000:00:1a.7: reg 10: [mem 0xfc404800-0xfc404bff]
[ 0.420209] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.420215] pci 0000:00:1a.7: PME# disabled
[ 0.420249] pci 0000:00:1b.0: [8086:284b] type 0 class 0x000403
[ 0.420274] pci 0000:00:1b.0: reg 10: [mem 0xfc400000-0xfc403fff 64bit]
[ 0.420391] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.420397] pci 0000:00:1b.0: PME# disabled
[ 0.420430] pci 0000:00:1c.0: [8086:283f] type 1 class 0x000604
[ 0.420552] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.420557] pci 0000:00:1c.0: PME# disabled
[ 0.420593] pci 0000:00:1c.1: [8086:2841] type 1 class 0x000604
[ 0.420715] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.420721] pci 0000:00:1c.1: PME# disabled
[ 0.420759] pci 0000:00:1c.2: [8086:2843] type 1 class 0x000604
[ 0.420881] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.420887] pci 0000:00:1c.2: PME# disabled
[ 0.420925] pci 0000:00:1c.4: [8086:2847] type 1 class 0x000604
[ 0.421047] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.421053] pci 0000:00:1c.4: PME# disabled
[ 0.421087] pci 0000:00:1d.0: [8086:2830] type 0 class 0x000c03
[ 0.421151] pci 0000:00:1d.0: reg 20: [io 0x1840-0x185f]
[ 0.421198] pci 0000:00:1d.1: [8086:2831] type 0 class 0x000c03
[ 0.421260] pci 0000:00:1d.1: reg 20: [io 0x1860-0x187f]
[ 0.421309] pci 0000:00:1d.2: [8086:2832] type 0 class 0x000c03
[ 0.421372] pci 0000:00:1d.2: reg 20: [io 0x1880-0x189f]
[ 0.421434] pci 0000:00:1d.7: [8086:2836] type 0 class 0x000c03
[ 0.421461] pci 0000:00:1d.7: reg 10: [mem 0xfc404c00-0xfc404fff]
[ 0.421579] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.421586] pci 0000:00:1d.7: PME# disabled
[ 0.421611] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
[ 0.421720] pci 0000:00:1f.0: [8086:2815] type 0 class 0x000601
[ 0.421846] pci 0000:00:1f.0: quirk: [io 0x1000-0x107f] claimed by ICH6 ACPI/GPIO/TCO
[ 0.421854] pci 0000:00:1f.0: quirk: [io 0x1180-0x11bf] claimed by ICH6 GPIO
[ 0.421924] pci 0000:00:1f.1: [8086:2850] type 0 class 0x000101
[ 0.421942] pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]
[ 0.421956] pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]
[ 0.421969] pci 0000:00:1f.1: reg 18: [io 0x0000-0x0007]
[ 0.421983] pci 0000:00:1f.1: reg 1c: [io 0x0000-0x0003]
[ 0.421996] pci 0000:00:1f.1: reg 20: [io 0x18a0-0x18af]
[ 0.422056] pci 0000:00:1f.2: [8086:2829] type 0 class 0x000106
[ 0.422086] pci 0000:00:1f.2: reg 10: [io 0x18d8-0x18df]
[ 0.422099] pci 0000:00:1f.2: reg 14: [io 0x18cc-0x18cf]
[ 0.422112] pci 0000:00:1f.2: reg 18: [io 0x18d0-0x18d7]
[ 0.422125] pci 0000:00:1f.2: reg 1c: [io 0x18c8-0x18cb]
[ 0.422139] pci 0000:00:1f.2: reg 20: [io 0x18e0-0x18ff]
[ 0.422152] pci 0000:00:1f.2: reg 24: [mem 0xfc404000-0xfc4047ff]
[ 0.422226] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.422232] pci 0000:00:1f.2: PME# disabled
[ 0.422256] pci 0000:00:1f.3: [8086:283e] type 0 class 0x000c05
[ 0.422275] pci 0000:00:1f.3: reg 10: [mem 0x00000000-0x000000ff]
[ 0.422322] pci 0000:00:1f.3: reg 20: [io 0x1c00-0x1c1f]
[ 0.422455] pci 0000:01:00.0: [10de:0426] type 0 class 0x000300
[ 0.422505] pci 0000:01:00.0: reg 10: [mem 0xce000000-0xceffffff]
[ 0.422559] pci 0000:01:00.0: reg 14: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.422613] pci 0000:01:00.0: reg 1c: [mem 0xcc000000-0xcdffffff 64bit]
[ 0.422649] pci 0000:01:00.0: reg 24: [io 0x2000-0x207f]
[ 0.422684] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.452044] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.452050] pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
[ 0.452054] pci 0000:00:01.0: bridge window [mem 0xcc000000-0xceffffff]
[ 0.452059] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.452133] pci 0000:00:1c.0: PCI bridge to [bus 02-03]
[ 0.452139] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
[ 0.452145] pci 0000:00:1c.0: bridge window [mem 0xf6000000-0xf7ffffff]
[ 0.452154] pci 0000:00:1c.0: bridge window [mem 0xf0000000-0xf1ffffff 64bit pref]
[ 0.452221] pci 0000:00:1c.1: PCI bridge to [bus 04-05]
[ 0.452227] pci 0000:00:1c.1: bridge window [io 0x4000-0x4fff]
[ 0.452233] pci 0000:00:1c.1: bridge window [mem 0xf8000000-0xf9ffffff]
[ 0.452242] pci 0000:00:1c.1: bridge window [mem 0xf2000000-0xf3ffffff 64bit pref]
[ 0.452379] pci 0000:06:00.0: [8086:4229] type 0 class 0x000280
[ 0.452439] pci 0000:06:00.0: reg 10: [mem 0xfa000000-0xfa001fff 64bit]
[ 0.452692] pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
[ 0.452706] pci 0000:06:00.0: PME# disabled
[ 0.460077] pci 0000:00:1c.2: PCI bridge to [bus 06-07]
[ 0.460083] pci 0000:00:1c.2: bridge window [io 0x5000-0x5fff]
[ 0.460089] pci 0000:00:1c.2: bridge window [mem 0xfa000000-0xfbffffff]
[ 0.460098] pci 0000:00:1c.2: bridge window [mem 0xf4000000-0xf5ffffff 64bit pref]
[ 0.460200] pci 0000:08:00.0: [11ab:4351] type 0 class 0x000200
[ 0.460234] pci 0000:08:00.0: reg 10: [mem 0xfc000000-0xfc003fff 64bit]
[ 0.460253] pci 0000:08:00.0: reg 18: [io 0x6000-0x60ff]
[ 0.460422] pci 0000:08:00.0: supports D1 D2
[ 0.460424] pci 0000:08:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.460432] pci 0000:08:00.0: PME# disabled
[ 0.468049] pci 0000:00:1c.4: PCI bridge to [bus 08-08]
[ 0.468055] pci 0000:00:1c.4: bridge window [io 0x6000-0x6fff]
[ 0.468061] pci 0000:00:1c.4: bridge window [mem 0xfc000000-0xfc0fffff]
[ 0.468129] pci 0000:09:03.0: [104c:8039] type 2 class 0x000607
[ 0.468158] pci 0000:09:03.0: reg 10: [mem 0xfc100000-0xfc100fff]
[ 0.468206] pci 0000:09:03.0: supports D1 D2
[ 0.468209] pci 0000:09:03.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.468215] pci 0000:09:03.0: PME# disabled
[ 0.468243] pci 0000:09:03.1: [104c:803a] type 0 class 0x000c00
[ 0.468271] pci 0000:09:03.1: reg 10: [mem 0xfc102000-0xfc1027ff]
[ 0.468288] pci 0000:09:03.1: reg 14: [mem 0xfc104000-0xfc107fff]
[ 0.468401] pci 0000:09:03.1: supports D1 D2
[ 0.468404] pci 0000:09:03.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.468410] pci 0000:09:03.1: PME# disabled
[ 0.468436] pci 0000:09:03.2: [104c:803b] type 0 class 0x000180
[ 0.468463] pci 0000:09:03.2: reg 10: [mem 0xfc101000-0xfc101fff]
[ 0.468585] pci 0000:09:03.2: supports D1 D2
[ 0.468588] pci 0000:09:03.2: PME# supported from D0 D1 D2 D3hot
[ 0.468594] pci 0000:09:03.2: PME# disabled
[ 0.468671] pci 0000:00:1e.0: PCI bridge to [bus 09-0a] (subtractive decode)
[ 0.468680] pci 0000:00:1e.0: bridge window [mem 0xfc100000-0xfc1fffff]
[ 0.468689] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
[ 0.468693] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xfffffffff] (subtractive decode)
[ 0.468749] pci_bus 0000:0a: [bus 0a-0d] partially hidden behind transparent bridge 0000:09 [bus 09-0a]
[ 0.468791] pci_bus 0000:00: on NUMA node 0
[ 0.468800] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.469042] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
[ 0.469219] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.469327] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.469433] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[ 0.469542] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
[ 0.469832] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.470137] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.470270] pci0000:00: ACPI _OSC request failed (AE_SUPPORT), returned control mask: 0x00
[ 0.470272] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.484221] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15)
[ 0.484284] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.484343] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *7 10 12 14 15)
[ 0.484403] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.484464] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[ 0.484523] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.484581] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.484639] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.484801] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.484808] vgaarb: loaded
[ 0.484810] vgaarb: bridge control possible 0000:01:00.0
[ 0.484953] i2c-core: driver [aat2870] using legacy suspend method
[ 0.484955] i2c-core: driver [aat2870] using legacy resume method
[ 0.485057] SCSI subsystem initialized
[ 0.485125] libata version 3.00 loaded.
[ 0.485180] usbcore: registered new interface driver usbfs
[ 0.485195] usbcore: registered new interface driver hub
[ 0.485227] usbcore: registered new device driver usb
[ 0.485336] PCI: Using ACPI for IRQ routing
[ 0.486873] Freeing initrd memory: 13824k freed
[ 0.497680] PCI: pci_cache_line_size set to 64 bytes
[ 0.497881] reserve RAM buffer: 000000000009f800 - 000000000009ffff
[ 0.497885] reserve RAM buffer: 000000007fed0000 - 000000007fffffff
[ 0.498060] NetLabel: Initializing
[ 0.498062] NetLabel: domain hash size = 128
[ 0.498064] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.498081] NetLabel: unlabeled traffic allowed by default
[ 0.498212] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.498212] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.498212] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.504156] Switching to clocksource hpet
[ 0.514017] AppArmor: AppArmor Filesystem Enabled
[ 0.514055] pnp: PnP ACPI init
[ 0.514079] ACPI: bus type pnp registered
[ 0.536440] pnp 00:00: [bus 00-ff]
[ 0.536444] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.536447] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.536450] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.536453] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.536456] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 0.536458] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 0.536461] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 0.536464] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 0.536466] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 0.536469] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 0.536472] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 0.536474] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 0.536477] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 0.536480] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 0.536483] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 0.536485] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 0.536488] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 0.536491] pnp 00:00: [mem 0x80000000-0xdfffffff window]
[ 0.536493] pnp 00:00: [mem 0xf0000000-0xfebfffff window]
[ 0.536496] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
[ 0.536576] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.536668] pnp 00:01: [mem 0xfed1c000-0xfed1ffff]
[ 0.536671] pnp 00:01: [mem 0xfed14000-0xfed17fff]
[ 0.536673] pnp 00:01: [mem 0xfed18000-0xfed18fff]
[ 0.536675] pnp 00:01: [mem 0xfed19000-0xfed19fff]
[ 0.536678] pnp 00:01: [mem 0xe0000000-0xefffffff]
[ 0.536680] pnp 00:01: [mem 0xfed20000-0xfed3ffff]
[ 0.536683] pnp 00:01: [mem 0xfed40000-0xfed44fff]
[ 0.536685] pnp 00:01: [mem 0xfed45000-0xfed8ffff]
[ 0.536765] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.536769] system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
[ 0.536772] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.536775] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.536778] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.536782] system 00:01: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.536785] system 00:01: [mem 0xfed40000-0xfed44fff] has been reserved
[ 0.536788] system 00:01: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.536792] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.537027] pnp 00:02: [io 0x0000-0x001f]
[ 0.537029] pnp 00:02: [io 0x0081-0x0091]
[ 0.537032] pnp 00:02: [io 0x0093-0x009f]
[ 0.537034] pnp 00:02: [io 0x00c0-0x00df]
[ 0.537037] pnp 00:02: [dma 4]
[ 0.537090] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.537101] pnp 00:03: [mem 0xff000000-0xffffffff]
[ 0.537153] pnp 00:03: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.537229] pnp 00:04: [mem 0xfed00000-0xfed003ff]
[ 0.537315] system 00:04: [mem 0xfed00000-0xfed003ff] has been reserved
[ 0.537319] system 00:04: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[ 0.537333] pnp 00:05: [io 0x00f0]
[ 0.537348] pnp 00:05: [irq 13]
[ 0.537402] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.537415] pnp 00:06: [io 0x002e-0x002f]
[ 0.537418] pnp 00:06: [io 0x004e-0x004f]
[ 0.537420] pnp 00:06: [io 0x0061]
[ 0.537422] pnp 00:06: [io 0x0063]
[ 0.537425] pnp 00:06: [io 0x0065]
[ 0.537427] pnp 00:06: [io 0x0067]
[ 0.537429] pnp 00:06: [io 0x0080]
[ 0.537431] pnp 00:06: [io 0x0092]
[ 0.537433] pnp 00:06: [io 0x00b2-0x00b3]
[ 0.537436] pnp 00:06: [io 0x0680-0x069f]
[ 0.537440] pnp 00:06: [io 0x0800-0x080f]
[ 0.537443] pnp 00:06: [io 0x1000-0x107f]
[ 0.537445] pnp 00:06: [io 0x1180-0x11bf]
[ 0.537447] pnp 00:06: [io 0x1640-0x164f]
[ 0.537450] pnp 00:06: [io 0xfe00-0xfe7f]
[ 0.537452] pnp 00:06: [io 0xfe80-0xfeff]
[ 0.537549] system 00:06: [io 0x0680-0x069f] has been reserved
[ 0.537553] system 00:06: [io 0x0800-0x080f] has been reserved
[ 0.537556] system 00:06: [io 0x1000-0x107f] has been reserved
[ 0.537559] system 00:06: [io 0x1180-0x11bf] has been reserved
[ 0.537562] system 00:06: [io 0x1640-0x164f] has been reserved
[ 0.537565] system 00:06: [io 0xfe00-0xfe7f] has been reserved
[ 0.537568] system 00:06: [io 0xfe80-0xfeff] has been reserved
[ 0.537572] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.537583] pnp 00:07: [io 0x0070-0x0077]
[ 0.537590] pnp 00:07: [irq 8]
[ 0.537645] pnp 00:07: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.537661] pnp 00:08: [io 0x0060]
[ 0.537664] pnp 00:08: [io 0x0064]
[ 0.537670] pnp 00:08: [irq 1]
[ 0.537725] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.537739] pnp 00:09: [irq 12]
[ 0.537799] pnp 00:09: Plug and Play ACPI device, IDs SNY9001 PNP0f13 (active)
[ 0.537822] pnp: PnP ACPI: found 10 devices
[ 0.537824] ACPI: ACPI bus type pnp unregistered
[ 0.537829] PnPBIOS: Disabled by ACPI PNP
[ 0.575467] PCI: max bus depth: 2 pci_try_num: 3
[ 0.575537] pci 0000:00:1f.3: BAR 0: assigned [mem 0x80000000-0x800000ff]
[ 0.575544] pci 0000:00:1f.3: BAR 0: set to [mem 0x80000000-0x800000ff] (PCI address [0x80000000-0x800000ff])
[ 0.575549] pci 0000:00:1e.0: BAR 15: assigned [mem 0x84000000-0x87ffffff pref]
[ 0.575554] pci 0000:00:1e.0: BAR 13: assigned [io 0x7000-0x7fff]
[ 0.575558] pci 0000:00:1c.4: BAR 15: assigned [mem 0x80100000-0x802fffff 64bit pref]
[ 0.575562] pci 0000:01:00.0: BAR 6: can't assign mem pref (size 0x20000)
[ 0.575566] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.575569] pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
[ 0.575573] pci 0000:00:01.0: bridge window [mem 0xcc000000-0xceffffff]
[ 0.575577] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.575583] pci 0000:00:1c.0: PCI bridge to [bus 02-03]
[ 0.575587] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
[ 0.575594] pci 0000:00:1c.0: bridge window [mem 0xf6000000-0xf7ffffff]
[ 0.575600] pci 0000:00:1c.0: bridge window [mem 0xf0000000-0xf1ffffff 64bit pref]
[ 0.575608] pci 0000:00:1c.1: PCI bridge to [bus 04-05]
[ 0.575612] pci 0000:00:1c.1: bridge window [io 0x4000-0x4fff]
[ 0.575620] pci 0000:00:1c.1: bridge window [mem 0xf8000000-0xf9ffffff]
[ 0.575625] pci 0000:00:1c.1: bridge window [mem 0xf2000000-0xf3ffffff 64bit pref]
[ 0.575635] pci 0000:00:1c.2: PCI bridge to [bus 06-07]
[ 0.575639] pci 0000:00:1c.2: bridge window [io 0x5000-0x5fff]
[ 0.575646] pci 0000:00:1c.2: bridge window [mem 0xfa000000-0xfbffffff]
[ 0.575651] pci 0000:00:1c.2: bridge window [mem 0xf4000000-0xf5ffffff 64bit pref]
[ 0.575660] pci 0000:00:1c.4: PCI bridge to [bus 08-08]
[ 0.575664] pci 0000:00:1c.4: bridge window [io 0x6000-0x6fff]
[ 0.575672] pci 0000:00:1c.4: bridge window [mem 0xfc000000-0xfc0fffff]
[ 0.575677] pci 0000:00:1c.4: bridge window [mem 0x80100000-0x802fffff 64bit pref]
[ 0.575689] pci 0000:09:03.0: BAR 16: assigned [mem 0x88000000-0x8bffffff]
[ 0.575693] pci 0000:09:03.0: BAR 15: assigned [mem 0x84000000-0x87ffffff pref]
[ 0.575696] pci 0000:09:03.0: BAR 14: assigned [io 0x7000-0x70ff]
[ 0.575699] pci 0000:09:03.0: BAR 13: assigned [io 0x7400-0x74ff]
[ 0.575701] pci 0000:09:03.0: CardBus bridge to [bus 0a-0d]
[ 0.575704] pci 0000:09:03.0: bridge window [io 0x7400-0x74ff]
[ 0.575710] pci 0000:09:03.0: bridge window [io 0x7000-0x70ff]
[ 0.575716] pci 0000:09:03.0: bridge window [mem 0x84000000-0x87ffffff pref]
[ 0.575723] pci 0000:09:03.0: bridge window [mem 0x88000000-0x8bffffff]
[ 0.575729] pci 0000:00:1e.0: PCI bridge to [bus 09-0a]
[ 0.575733] pci 0000:00:1e.0: bridge window [io 0x7000-0x7fff]
[ 0.575740] pci 0000:00:1e.0: bridge window [mem 0xfc100000-0xfc1fffff]
[ 0.575746] pci 0000:00:1e.0: bridge window [mem 0x84000000-0x87ffffff pref]
[ 0.575768] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.575773] pci 0000:00:01.0: setting latency timer to 64
[ 0.575786] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.575791] pci 0000:00:1c.0: setting latency timer to 64
[ 0.575800] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.575805] pci 0000:00:1c.1: setting latency timer to 64
[ 0.575817] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.575823] pci 0000:00:1c.2: setting latency timer to 64
[ 0.575831] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.575837] pci 0000:00:1c.4: setting latency timer to 64
[ 0.575847] pci 0000:00:1e.0: setting latency timer to 64
[ 0.575857] pci 0000:09:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.575864] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.575867] pci_bus 0000:00: resource 1 [mem 0x00000000-0xfffffffff]
[ 0.575870] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
[ 0.575872] pci_bus 0000:01: resource 1 [mem 0xcc000000-0xceffffff]
[ 0.575875] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.575878] pci_bus 0000:02: resource 0 [io 0x3000-0x3fff]
[ 0.575881] pci_bus 0000:02: resource 1 [mem 0xf6000000-0xf7ffffff]
[ 0.575884] pci_bus 0000:02: resource 2 [mem 0xf0000000-0xf1ffffff 64bit pref]
[ 0.575887] pci_bus 0000:04: resource 0 [io 0x4000-0x4fff]
[ 0.575889] pci_bus 0000:04: resource 1 [mem 0xf8000000-0xf9ffffff]
[ 0.575892] pci_bus 0000:04: resource 2 [mem 0xf2000000-0xf3ffffff 64bit pref]
[ 0.575895] pci_bus 0000:06: resource 0 [io 0x5000-0x5fff]
[ 0.575897] pci_bus 0000:06: resource 1 [mem 0xfa000000-0xfbffffff]
[ 0.575900] pci_bus 0000:06: resource 2 [mem 0xf4000000-0xf5ffffff 64bit pref]
[ 0.575903] pci_bus 0000:08: resource 0 [io 0x6000-0x6fff]
[ 0.575906] pci_bus 0000:08: resource 1 [mem 0xfc000000-0xfc0fffff]
[ 0.575909] pci_bus 0000:08: resource 2 [mem 0x80100000-0x802fffff 64bit pref]
[ 0.575911] pci_bus 0000:09: resource 0 [io 0x7000-0x7fff]
[ 0.575914] pci_bus 0000:09: resource 1 [mem 0xfc100000-0xfc1fffff]
[ 0.575917] pci_bus 0000:09: resource 2 [mem 0x84000000-0x87ffffff pref]
[ 0.575919] pci_bus 0000:09: resource 4 [io 0x0000-0xffff]
[ 0.575922] pci_bus 0000:09: resource 5 [mem 0x00000000-0xfffffffff]
[ 0.575925] pci_bus 0000:0a: resource 0 [io 0x7400-0x74ff]
[ 0.575927] pci_bus 0000:0a: resource 1 [io 0x7000-0x70ff]
[ 0.575930] pci_bus 0000:0a: resource 2 [mem 0x84000000-0x87ffffff pref]
[ 0.575933] pci_bus 0000:0a: resource 3 [mem 0x88000000-0x8bffffff]
[ 0.575979] NET: Registered protocol family 2
[ 0.576075] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.576365] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.576806] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.576995] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.576998] TCP reno registered
[ 0.577001] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.577009] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.577080] NET: Registered protocol family 1
[ 0.577110] pci 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.577134] pci 0000:00:1a.0: PCI INT A disabled
[ 0.577150] pci 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.577172] pci 0000:00:1a.1: PCI INT B disabled
[ 0.577183] pci 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.577218] pci 0000:00:1a.7: PCI INT C disabled
[ 0.577246] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.577266] pci 0000:00:1d.0: PCI INT A disabled
[ 0.577278] pci 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.577300] pci 0000:00:1d.1: PCI INT B disabled
[ 0.577308] pci 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.577329] pci 0000:00:1d.2: PCI INT C disabled
[ 0.577340] pci 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.577359] pci 0000:00:1d.7: PCI INT A disabled
[ 0.577438] PCI: CLS 64 bytes, default 64
[ 0.577446] Simple Boot Flag at 0x36 set to 0x1
[ 0.577872] audit: initializing netlink socket (disabled)
[ 0.577883] type=2000 audit(1347581432.572:1): initialized
[ 0.605527] highmem bounce pool size: 64 pages
[ 0.605533] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.614318] VFS: Disk quotas dquot_6.5.2
[ 0.614405] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.615087] fuse init (API version 7.17)
[ 0.615205] msgmni has been set to 1712
[ 0.615659] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.615693] io scheduler noop registered
[ 0.615695] io scheduler deadline registered
[ 0.615703] io scheduler cfq registered (default)
[ 0.615848] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.615888] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[ 0.615950] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.616024] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[ 0.616112] pcieport 0000:00:1c.1: setting latency timer to 64
[ 0.616171] pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
[ 0.616257] pcieport 0000:00:1c.2: setting latency timer to 64
[ 0.616316] pcieport 0000:00:1c.2: irq 43 for MSI/MSI-X
[ 0.616405] pcieport 0000:00:1c.4: setting latency timer to 64
[ 0.616464] pcieport 0000:00:1c.4: irq 44 for MSI/MSI-X
[ 0.616578] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.616608] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.616710] intel_idle: MWAIT substates: 0x22220
[ 0.616712] intel_idle: does not run on family 6 model 15
[ 0.632039] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 0.648048] ACPI: AC Adapter [ADP1] (on-line)
[ 0.648137] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0
[ 0.664036] ACPI: Lid Switch [LID0]
[ 0.664090] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 0.664095] ACPI: Power Button [PWRB]
[ 0.698425] Monitor-Mwait will be used to enter C-1 state
[ 0.698468] Monitor-Mwait will be used to enter C-2 state
[ 0.698511] Monitor-Mwait will be used to enter C-3 state
[ 0.698523] Marking TSC unstable due to TSC halts in idle
[ 0.698539] ACPI: acpi_idle registered with cpuidle
[ 0.752049] thermal LNXTHERM:00: registered as thermal_zone0
[ 0.752052] ACPI: Thermal Zone [TZ00] (59 C)
[ 0.768135] ACPI: Invalid active0 threshold
[ 0.784048] thermal LNXTHERM:01: registered as thermal_zone1
[ 0.784051] ACPI: Thermal Zone [TZ01] (59 C)
[ 0.784070] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 0.784080] ACPI: Battery Slot [BAT0] (battery present)
[ 0.784121] ERST: Table is not found!
[ 0.784123] GHES: HEST is not enabled!
[ 0.784173] isapnp: Scanning for PnP cards...
[ 0.784212] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 1.080101] ACPI: Battery Slot [BAT0] (battery present)
[ 1.138287] isapnp: No Plug & Play device found
[ 1.188418] Linux agpgart interface v0.103
[ 1.190522] brd: module loaded
[ 1.191496] loop: module loaded
[ 1.191651] ahci 0000:00:1f.2: version 3.0
[ 1.191665] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.191717] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X
[ 1.191779] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x1 impl SATA mode
[ 1.191784] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc
[ 1.191790] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.192234] scsi0 : ahci
[ 1.192349] scsi1 : ahci
[ 1.192448] scsi2 : ahci
[ 1.192548] ata1: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404100 irq 45
[ 1.192551] ata2: DUMMY
[ 1.192553] ata3: DUMMY
[ 1.192646] ata_piix 0000:00:1f.1: version 2.13
[ 1.192656] ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 1.192695] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 1.193074] scsi3 : ata_piix
[ 1.193165] scsi4 : ata_piix
[ 1.193670] ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18a0 irq 14
[ 1.193674] ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18a8 irq 15
[ 1.194138] Fixed MDIO Bus: probed
[ 1.194162] tun: Universal TUN/TAP device driver, 1.6
[ 1.194165] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.194331] PPP generic driver version 2.4.2
[ 1.194462] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.194481] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.194497] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 1.194502] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 1.194562] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 1.194596] ehci_hcd 0000:00:1a.7: debug port 1
[ 1.198475] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
[ 1.198492] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfc404800
[ 1.212021] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 1.212174] hub 1-0:1.0: USB hub found
[ 1.212180] hub 1-0:1.0: 4 ports detected
[ 1.212273] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.212286] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.212290] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.212351] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 1.212382] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.216269] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[ 1.216286] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfc404c00
[ 1.232020] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.232175] hub 2-0:1.0: USB hub found
[ 1.232180] hub 2-0:1.0: 6 ports detected
[ 1.232277] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.232295] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.232315] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.232324] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 1.232328] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.232392] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 1.232433] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800
[ 1.232593] hub 3-0:1.0: USB hub found
[ 1.232598] hub 3-0:1.0: 2 ports detected
[ 1.232682] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 1.232691] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 1.232695] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.232748] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 1.232788] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820
[ 1.232940] hub 4-0:1.0: USB hub found
[ 1.232944] hub 4-0:1.0: 2 ports detected
[ 1.233029] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.233038] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.233042] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.233094] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 1.233123] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840
[ 1.233275] hub 5-0:1.0: USB hub found
[ 1.233279] hub 5-0:1.0: 2 ports detected
[ 1.233362] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.233371] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.233375] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.233431] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 1.233471] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001860
[ 1.233621] hub 6-0:1.0: USB hub found
[ 1.233626] hub 6-0:1.0: 2 ports detected
[ 1.233710] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.233719] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.233723] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.233781] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 1.233811] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001880
[ 1.233962] hub 7-0:1.0: USB hub found
[ 1.233967] hub 7-0:1.0: 2 ports detected
[ 1.234112] usbcore: registered new interface driver libusual
[ 1.234166] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.237834] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.237841] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.238000] mousedev: PS/2 mouse device common for all mice
[ 1.238244] rtc_cmos 00:07: RTC can wake from S4
[ 1.238390] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 1.238424] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 1.238488] device-mapper: uevent: version 1.0.3
[ 1.238592] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 1.238633] EISA: Probing bus 0 at eisa.0
[ 1.238640] Cannot allocate resource for EISA slot 1
[ 1.238643] Cannot allocate resource for EISA slot 2
[ 1.238646] Cannot allocate resource for EISA slot 3
[ 1.238648] Cannot allocate resource for EISA slot 4
[ 1.238650] Cannot allocate resource for EISA slot 5
[ 1.238653] Cannot allocate resource for EISA slot 6
[ 1.238655] Cannot allocate resource for EISA slot 7
[ 1.238662] EISA: Detected 0 cards.
[ 1.238680] cpufreq-nforce2: No nForce2 chipset.
[ 1.238767] cpuidle: using governor ladder
[ 1.238899] cpuidle: using governor menu
[ 1.238902] EFI Variables Facility v0.08 2004-May-17
[ 1.239231] TCP cubic registered
[ 1.239372] NET: Registered protocol family 10
[ 1.240084] NET: Registered protocol family 17
[ 1.240089] Registering the dns_resolver key type
[ 1.240110] Using IPI No-Shortcut mode
[ 1.240334] PM: Hibernation image not present or could not be loaded.
[ 1.240356] registered taskstats version 1
[ 1.243907] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 1.252030] Magic number: 12:681:152
[ 1.252056] bdi 1:4: hash matches
[ 1.252162] rtc_cmos 00:07: setting system clock to 2012-09-14 00:10:34 UTC (1347581434)
[ 1.252760] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.252762] EDD information not available.
[ 1.359849] ata4.00: ATAPI: MATSHITABD-CMB UJ-120, 1.04, max UDMA/33
[ 1.376387] ata4.00: configured for UDMA/33
[ 1.512103] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.512782] ata1.00: ACPI cmd ef/90:03:00:00:00:a0 (SET FEATURES) succeeded
[ 1.512787] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 1.513284] ata1.00: ATA-8: FUJITSU MHY2200BH, 0000000B, max UDMA/100
[ 1.513287] ata1.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.514092] ata1.00: ACPI cmd ef/90:03:00:00:00:a0 (SET FEATURES) succeeded
[ 1.514096] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 1.514594] ata1.00: configured for UDMA/100
[ 1.514788] scsi 0:0:0:0: Direct-Access ATA FUJITSU MHY2200B 0000 PQ: 0 ANSI: 5
[ 1.514961] sd 0:0:0:0: [sda] 390721968 512-byte logical blocks: (200 GB/186 GiB)
[ 1.514986] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.515015] sd 0:0:0:0: [sda] Write Protect is off
[ 1.515019] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.515042] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.517146] scsi 3:0:0:0: CD-ROM MATSHITA BD-CMB UJ-120 1.04 PQ: 0 ANSI: 5
[ 1.520305] sr0: scsi3-mmc drive: 62x/62x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.520308] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.520464] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 1.520607] sr 3:0:0:0: Attached scsi generic sg1 type 5
[ 1.524050] usb 1-2: new high-speed USB device number 2 using ehci_hcd
[ 1.617295] sda: sda1 sda2 < sda5 >
[ 1.617962] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.618115] Freeing unused kernel memory: 740k freed
[ 1.618454] Write protecting the kernel text: 5816k
[ 1.618488] Write protecting the kernel read-only data: 2376k
[ 1.618490] NX-protecting the kernel data: 4424k
[ 1.637479] udevd[100]: starting version 175
[ 1.733532] sky2: driver version 1.30
[ 1.733578] sky2 0000:08:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.733596] sky2 0000:08:00.0: setting latency timer to 64
[ 1.733630] sky2 0000:08:00.0: Yukon-2 FE chip revision 1
[ 1.733743] sky2 0000:08:00.0: irq 46 for MSI/MSI-X
[ 1.734435] sky2 0000:08:00.0: eth0: addr 00:1a:80:1e:30:49
[ 1.761183] firewire_ohci 0000:09:03.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.820169] firewire_ohci: Added fw-ohci device 0000:09:03.1, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x2
[ 1.975353] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 2.128039] usb 5-2: new low-speed USB device number 2 using uhci_hcd
[ 2.320174] firewire_core: created device fw0: GUID 08004603027af374, S400
[ 2.556080] usb 7-1: new full-speed USB device number 2 using uhci_hcd
[ 2.730921] hub 7-1:1.0: USB hub found
[ 2.732882] hub 7-1:1.0: 3 ports detected
[ 3.013889] usb 7-1.1: new full-speed USB device number 3 using uhci_hcd
[ 3.221889] usb 7-1.2: new full-speed USB device number 4 using uhci_hcd
[ 3.417891] usb 7-1.3: new full-speed USB device number 5 using uhci_hcd
[ 17.059341] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 17.261565] udevd[324]: starting version 175
[ 17.402774] Adding 2094076k swap on /dev/sda5. Priority:-1 extents:1 across:2094076k
[ 18.172372] lp: driver loaded but no devices found
[ 18.241706] wmi: Mapper loaded
[ 18.336539] [drm] Initialized drm 1.1.0 20060810
[ 18.439938] nouveau 0000:01:00.0: enabling device (0000 -> 0003)
[ 18.439948] nouveau 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 18.439957] nouveau 0000:01:00.0: setting latency timer to 64
[ 18.441809] [drm] nouveau 0000:01:00.0: Unsupported chipset 0xffffffff
[ 18.442739] nouveau 0000:01:00.0: PCI INT A disabled
[ 18.442746] nouveau: probe of 0000:01:00.0 failed with error -22
[ 18.472433] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 18.774309] sony_laptop: Sony Notebook Control Driver v0.6
[ 18.777229] input: Sony Vaio Keys as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:28/SNY5001:00/input/input3
[ 18.777363] input: Sony Vaio Jogdial as /devices/virtual/input/input4
[ 18.807321] tifm_7xx1 0000:09:03.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 19.056842] cfg80211: Calling CRDA to update world regulatory domain
[ 19.083641] yenta_cardbus 0000:09:03.0: CardBus bridge found [104d:9005]
[ 19.083666] yenta_cardbus 0000:09:03.0: Using CSCINT to route CSC interrupts to PCI
[ 19.083669] yenta_cardbus 0000:09:03.0: Routing CardBus interrupts to PCI
[ 19.083676] yenta_cardbus 0000:09:03.0: TI: mfunc 0x01121b22, devctl 0x64
[ 19.093165] Bluetooth: Core ver 2.16
[ 19.093195] NET: Registered protocol family 31
[ 19.093197] Bluetooth: HCI device and connection manager initialized
[ 19.093201] Bluetooth: HCI socket layer initialized
[ 19.093203] Bluetooth: L2CAP socket layer initialized
[ 19.093209] Bluetooth: SCO socket layer initialized
[ 19.122023] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 19.122453] usbcore: registered new interface driver btusb
[ 19.312827] yenta_cardbus 0000:09:03.0: ISA IRQ mask 0x0cf8, PCI irq 16
[ 19.312833] yenta_cardbus 0000:09:03.0: Socket status: 30000006
[ 19.312837] pci_bus 0000:09: Raising subordinate bus# of parent bus (#09) from #0a to #0d
[ 19.312848] yenta_cardbus 0000:09:03.0: pcmcia: parent PCI bridge window: [io 0x7000-0x7fff]
[ 19.312852] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x7000-0x7fff: excluding 0x7000-0x70ff 0x7400-0x74ff
[ 19.319941] yenta_cardbus 0000:09:03.0: pcmcia: parent PCI bridge window: [mem 0xfc100000-0xfc1fffff]
[ 19.319945] pcmcia_socket pcmcia_socket0: cs: memory probe 0xfc100000-0xfc1fffff: excluding 0xfc100000-0xfc10ffff
[ 19.319963] yenta_cardbus 0000:09:03.0: pcmcia: parent PCI bridge window: [mem 0x84000000-0x87ffffff pref]
[ 19.319967] pcmcia_socket pcmcia_socket0: cs: memory probe 0x84000000-0x87ffffff: excluding 0x84000000-0x87ffffff
[ 19.550978] input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input5
[ 19.567547] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input6
[ 19.755861] input: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input7
[ 19.755993] generic-usb 0003:045E:0039.0001: input,hidraw0: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.0-2/input0
[ 19.759457] input: HID 044e:3013 as /devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1.2/7-1.2:1.0/input/input8
[ 19.759618] generic-usb 0003:044E:3013.0002: input,hidraw1: USB HID v1.11 Keyboard [HID 044e:3013] on usb-0000:00:1d.2-1.2/input0
[ 19.762793] input: HID 044e:3012 as /devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1.3/7-1.3:1.0/input/input9
[ 19.763069] generic-usb 0003:044E:3012.0003: input,hidraw2: USB HID v1.11 Mouse [HID 044e:3012] on usb-0000:00:1d.2-1.3/input0
[ 19.763148] usbcore: registered new interface driver usbhid
[ 19.763151] usbhid: USB HID core driver
[ 19.774858] usb 7-1.2: input irq status -75 received
[ 19.790875] usb 7-1.2: input irq status -75 received
[ 19.806859] usb 7-1.2: input irq status -75 received
[ 19.822850] usb 7-1.2: input irq status -75 received
[ 19.838851] usb 7-1.2: input irq status -75 received
[ 19.846219] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x1f0-0x1f7 0x370-0x377
[ 19.848373] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x4d0-0x4d7
[ 19.849252] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 19.849974] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 19.850768] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xcffff 0xdc000-0xfffff
[ 19.850799] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: clean.
[ 19.850831] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
[ 19.850859] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 19.854875] usb 7-1.2: input irq status -75 received
[ 19.870878] usb 7-1.2: input irq status -75 received
[ 19.886885] usb 7-1.2: input irq status -75 received
[ 19.902879] usb 7-1.2: input irq status -75 received
[ 19.918882] usb 7-1.2: input irq status -75 received
[ 19.970153] Linux video capture interface: v2.00
[ 19.996654] uvcvideo: Found UVC 1.00 device <unnamed> (05ca:183b)
[ 19.997512] input: UVC Camera (05ca:183b) as /devices/pci0000:00/0000:00:1a.7/usb1/1-2/1-2:1.0/input/input10
[ 19.997643] usbcore: registered new interface driver uvcvideo
[ 19.997652] USB Video Class driver (1.1.1)
[ 20.028123] usbcore: deregistering interface driver uvcvideo
[ 20.030635] iwl4965: Intel(R) Wireless WiFi 4965 driver for Linux, in-tree:
[ 20.030639] iwl4965: Copyright(c) 2003-2011 Intel Corporation
[ 20.030727] iwl4965 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 20.030757] iwl4965 0000:06:00.0: setting latency timer to 64
[ 20.030813] iwl4965 0000:06:00.0: Detected Intel(R) Wireless WiFi Link 4965AGN, REV=0x4
[ 20.073434] iwl4965 0000:06:00.0: device EEPROM VER=0x36, CALIB=0x5
[ 20.073506] iwl4965 0000:06:00.0: Tunable channels: 13 802.11bg, 19 802.11a channels
[ 20.073649] iwl4965 0000:06:00.0: irq 47 for MSI/MSI-X
[ 20.111511] Linux video capture interface: v2.00
[ 20.112622] uvcvideo: Found UVC 1.00 device <unnamed> (05ca:183b)
[ 20.113543] input: UVC Camera (05ca:183b) as /devices/pci0000:00/0000:00:1a.7/usb1/1-2/1-2:1.0/input/input11
[ 20.113733] usbcore: registered new interface driver uvcvideo
[ 20.113736] USB Video Class driver (1.1.1)
[ 20.128106] usbcore: deregistering interface driver uvcvideo
[ 20.175347] Linux video capture interface: v2.00
[ 20.176211] uvcvideo: Found UVC 1.00 device <unnamed> (05ca:183b)
[ 20.177452] input: UVC Camera (05ca:183b) as /devices/pci0000:00/0000:00:1a.7/usb1/1-2/1-2:1.0/input/input12
[ 20.178200] usbcore: registered new interface driver uvcvideo
[ 20.178203] USB Video Class driver (1.1.1)
[ 20.361673] iwl4965 0000:06:00.0: loaded firmware version 228.61.2.24
[ 20.361889] Registered led device: phy0-led
[ 20.361925] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[ 20.550979] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 20.551057] snd_hda_intel 0000:00:1b.0: irq 48 for MSI/MSI-X
[ 20.551097] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 20.616944] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[ 20.617124] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
[ 20.640626] ieee80211 phy0: Selected rate control algorithm 'iwl-4965-rs'
[ 20.854027] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[ 20.854031] cfg80211: World regulatory domain updated:
[ 20.854033] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 20.854036] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.854039] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 20.854042] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 20.854044] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.854047] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 21.629737] nvidia: module license 'NVIDIA' taints kernel.
[ 21.629740] Disabling lock debugging due to kernel taint
[ 21.997393] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 21.997407] nvidia 0000:01:00.0: setting latency timer to 64
[ 21.997413] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 21.997447] NVRM: The NVIDIA GPU 0000:01:00.0 (PCI ID: 10de:0426) installed
[ 21.997449] NVRM: in this system is not supported by the 304.43 NVIDIA Linux
[ 21.997450] NVRM: graphics driver release. Please see 'Appendix A -
[ 21.997451] NVRM: Supported NVIDIA GPU Products' in this release's README,
[ 21.997452] NVRM: available on the Linux graphics driver download page at
[ 21.997453] NVRM: www.nvidia.com.
[ 21.997462] nvidia 0000:01:00.0: PCI INT A disabled
[ 21.997471] nvidia: probe of 0000:01:00.0 failed with error -1
[ 21.997503] NVRM: The NVIDIA probe routine failed for 1 device(s).
[ 21.997506] NVRM: None of the NVIDIA graphics adapters were initialized!
[ 22.026048] type=1400 audit(1347581455.270:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=837 comm="apparmor_parser"
[ 22.026060] type=1400 audit(1347581455.270:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=766 comm="apparmor_parser"
[ 22.026543] type=1400 audit(1347581455.270:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=766 comm="apparmor_parser"
[ 22.026553] type=1400 audit(1347581455.270:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=837 comm="apparmor_parser"
[ 22.026814] type=1400 audit(1347581455.270:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=766 comm="apparmor_parser"
[ 22.026833] type=1400 audit(1347581455.270:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=837 comm="apparmor_parser"
[ 22.027449] type=1400 audit(1347581455.270:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=765 comm="apparmor_parser"
[ 22.027933] type=1400 audit(1347581455.270:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=765 comm="apparmor_parser"
[ 22.028236] type=1400 audit(1347581455.274:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=765 comm="apparmor_parser"
[ 22.578809] vesafb: mode is 640x480x32, linelength=2560, pages=0
[ 22.578815] vesafb: scrolling: redraw
[ 22.578818] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 22.580509] vesafb: framebuffer at 0xcd000000, mapped to 0xf8880000, using 1216k, total 1216k
[ 22.580657] Console: switching to colour frame buffer device 80x30
[ 22.580674] fb0: VESA VGA frame buffer device
[ 22.594681] ppdev: user-space parallel port driver
[ 22.789630] type=1400 audit(1347581456.034:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=944 comm="apparmor_parser"
[ 22.844732] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 22.844735] Bluetooth: BNEP filters: protocol multicast
[ 22.991822] Bluetooth: RFCOMM TTY layer initialized
[ 22.991828] Bluetooth: RFCOMM socket layer initialized
[ 22.991831] Bluetooth: RFCOMM ver 1.11
[ 23.082731] init: failsafe main process (915) killed by TERM signal
[ 25.321309] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 25.321876] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 25.327486] sky2 0000:08:00.0: eth0: enabling interface
[ 25.327727] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 25.328336] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 26.117870] kvm: disabled by bios
[ 26.149059] init: qemu-kvm pre-start process (1082) terminated with status 1
[ 26.397656] init: libvirt-bin main process (1181) terminated with status 127
[ 26.397690] init: libvirt-bin main process ended, respawning
[ 31.727620] wlan0: authenticate with 02:1e:58:07:fe:06 (try 1)
[ 31.729461] wlan0: authenticated
[ 31.748302] wlan0: associate with 02:1e:58:07:fe:06 (try 1)
[ 31.750771] wlan0: RX AssocResp from 02:1e:58:07:fe:06 (capab=0x411 status=0 aid=3)
[ 31.750775] wlan0: associated
[ 31.778412] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 42.648075] wlan0: no IPv6 routers present
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-29-generic-pae (buildd@roseapple) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #46-Ubuntu SMP Fri Jul 27 17:25:43 UTC 2012 (Ubuntu 3.2.0-29.46-generic-pae 3.2.24)
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fed0000 (usable)
[ 0.000000] BIOS-e820: 000000007fed0000 - 000000007fee0000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007fee0000 - 000000007fee3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007fee3000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI present.
[ 0.000000] DMI: Sony Corporation VGN-FZ21M/VAIO, BIOS R1120J7 07/04/2007
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0x7fed0 max_arch_pfn = 0x1000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07FF00000 mask FFFF00000 uncachable
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] original variable MTRRs
[ 0.000000] reg 0, base: 0GB, range: 2GB, type WB
[ 0.000000] reg 1, base: 2047MB, range: 1MB, type UC
[ 0.000000] total RAM covered: 2047M
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.000000] gran_size: 64K chunk_size: 2M num_reg: 2 lose cover RAM: 0G
[ 0.000000] New variable MTRRs
[ 0.000000] reg 0, base: 0GB, range: 2GB, type WB
[ 0.000000] reg 1, base: 2047MB, range: 1MB, type UC
[ 0.000000] found SMP MP-table at [c00f8090] f8090
[ 0.000000] initial memory mapped : 0 - 02000000
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: 0000000000000000-0000000037bfe000
[ 0.000000] 0000000000 - 0000200000 page 4k
[ 0.000000] 0000200000 - 0037a00000 page 2M
[ 0.000000] 0037a00000 - 0037bfe000 page 4k
[ 0.000000] kernel direct mapping tables up to 37bfe000 @ 1ffb000-2000000
[ 0.000000] RAMDISK: 364f0000 - 37270000
[ 0.000000] ACPI: RSDP 000f8060 00024 (v02 PTLTD )
[ 0.000000] ACPI: XSDT 7fed7f39 00084 (v01 Sony VAIO 20070704 PTL 00000000)
[ 0.000000] ACPI: FACP 7fedfc04 000F4 (v03 Sony VAIO 20070704 PTL 00000001)
[ 0.000000] ACPI: DSDT 7fed9217 06979 (v02 Sony VAIO 20070704 PTL 20050624)
[ 0.000000] ACPI: FACS 7fee2fc0 00040
[ 0.000000] ACPI: APIC 7fedfcf8 00068 (v01 Sony VAIO 20070704 PTL 0000005A)
[ 0.000000] ACPI: HPET 7fedfd60 00038 (v01 Sony VAIO 20070704 PTL 0000005A)
[ 0.000000] ACPI: MCFG 7fedfd98 0003C (v01 Sony VAIO 20070704 PTL 0000005A)
[ 0.000000] ACPI: SLIC 7fedfdd4 00176 (v01 Sony VAIO 20070704 PTL 01000000)
[ 0.000000] ACPI: TMOR 7fedff4a 00026 (v01 Sony VAIO 20070704 PTL 00000003)
[ 0.000000] ACPI: APIC 7fedff70 00068 (v01 Sony VAIO 20070704 PTL 00000000)
[ 0.000000] ACPI: BOOT 7fedffd8 00028 (v01 Sony VAIO 20070704 PTL 00000001)
[ 0.000000] ACPI: SSDT 7fed90fa 0011D (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.000000] ACPI: SSDT 7fed85a5 00287 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.000000] ACPI: SSDT 7fed84f1 000B4 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.000000] ACPI: SSDT 7fed7fbd 00534 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.000000] ACPI: BIOS bug: multiple APIC/MADT found, using 0
[ 0.000000] ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 1154MB HIGHMEM available.
[ 0.000000] 891MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 37bfe000
[ 0.000000] low ram: 0 - 37bfe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x00037bfe
[ 0.000000] HighMem 0x00037bfe -> 0x0007fed0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007fed0
[ 0.000000] On node 0 totalpages: 523871
[ 0.000000] free_area_init_node: node 0, pgdat c1866a40, node_mem_map f54f0200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1752 pages used for memmap
[ 0.000000] Normal zone: 222502 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2310 pages used for memmap
[ 0.000000] HighMem zone: 293324 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000ce000
[ 0.000000] PM: Registered nosave memory: 00000000000ce000 - 00000000000d0000
[ 0.000000] PM: Registered nosave memory: 00000000000d0000 - 00000000000dc000
[ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:60000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @f7bd5000 s34240 r0 d23104 u57344
[ 0.000000] pcpu-alloc: s34240 r0 d23104 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519777
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-29-generic-pae root=UUID=d4000f4c-a9db-4cd9-b0fc-d39e29a75a2e ro acpi_osi=Linux quiet splash acpi_backlight=vendor vt.handoff=7
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 8383488 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Initializing HighMem for node 0 (00037bfe:0007fed0)
[ 0.000000] Memory: 2045764k/2095936k available (5814k kernel code, 49720k reserved, 2841k data, 740k init, 1182536k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
[ 0.000000] pkmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xf83fe000 - 0xffbfe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf7bfe000 ( 891 MB)
[ 0.000000] .init : 0xc1875000 - 0xc192e000 ( 740 kB)
[ 0.000000] .data : 0xc15adb64 - 0xc1874240 (2841 kB)
[ 0.000000] .text : 0xc1000000 - 0xc15adb64 (5814 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:2304 nr_irqs:512 16
[ 0.000000] CPU 0 irqstacks, hard=f5008000 soft=f500a000
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] vt handoff: transparent VT on vt#7
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1994.800 MHz processor.
[ 0.004002] Calibrating delay loop (skipped), value calculated using timer frequency.. 3989.60 BogoMIPS (lpj=7979200)
[ 0.004007] pid_max: default: 32768 minimum: 301
[ 0.004029] Security Framework initialized
[ 0.004047] AppArmor: AppArmor initialized
[ 0.004049] Yama: becoming mindful.
[ 0.004105] Mount-cache hash table entries: 512
[ 0.004244] Initializing cgroup subsys cpuacct
[ 0.004250] Initializing cgroup subsys memory
[ 0.004258] Initializing cgroup subsys devices
[ 0.004260] Initializing cgroup subsys freezer
[ 0.004263] Initializing cgroup subsys blkio
[ 0.004270] Initializing cgroup subsys perf_event
[ 0.004297] CPU: Physical Processor ID: 0
[ 0.004299] CPU: Processor Core ID: 0
[ 0.004303] mce: CPU supports 6 MCE banks
[ 0.004311] CPU0: Thermal monitoring enabled (TM2)
[ 0.004314] using mwait in idle threads.
[ 0.009299] ACPI: Core revision 20110623
[ 0.016031] ftrace: allocating 26545 entries in 52 pages
[ 0.020051] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.024242] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.063931] CPU0: Intel(R) Core(TM)2 Duo CPU T7250 @ 2.00GHz stepping 0d
[ 0.064003] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
[ 0.064003] PEBS disabled due to CPU errata.
[ 0.064003] ... version: 2
[ 0.064003] ... bit width: 40
[ 0.064003] ... generic registers: 2
[ 0.064003] ... value mask: 000000ffffffffff
[ 0.064003] ... max period: 000000007fffffff
[ 0.064003] ... fixed-purpose events: 3
[ 0.064003] ... event mask: 0000000700000003
[ 0.064003] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.064003] CPU 1 irqstacks, hard=f50ea000 soft=f50ec000
[ 0.064003] Booting Node 0, Processors #1 Ok.
[ 0.064003] smpboot cpu 1: start_ip = 9b000
[ 0.008000] Initializing CPU#1
[ 0.152038] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.152080] Brought up 2 CPUs
[ 0.152083] Total of 2 processors activated (7979.57 BogoMIPS).
[ 0.153436] devtmpfs: initialized
[ 0.153436] EVM: security.selinux
[ 0.153436] EVM: security.SMACK64
[ 0.153436] EVM: security.capability
[ 0.153436] PM: Registering ACPI NVS region at 7fee0000 (12288 bytes)
[ 0.153436] print_constraints: dummy:
[ 0.153436] RTC time: 0:20:01, date: 09/14/12
[ 0.153436] NET: Registered protocol family 16
[ 0.153436] Trying to unpack rootfs image as initramfs...
[ 0.153441] EISA bus registered
[ 0.153458] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.153462] ACPI: bus type pci registered
[ 0.153537] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.153541] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.153543] PCI: Using MMCONFIG for extended config space
[ 0.153545] PCI: Using configuration type 1 for base access
[ 0.156741] bio: create slab <bio-0> at 0
[ 0.156839] ACPI: Added _OSI(Module Device)
[ 0.156842] ACPI: Added _OSI(Processor Device)
[ 0.156845] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.156847] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.156850] ACPI: Added _OSI(Linux)
[ 0.158624] ACPI: EC: Look up EC in DSDT
[ 0.161726] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query honored via cmdline
[ 0.162957] ACPI: SSDT 7fed8d75 002A1 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.163395] ACPI: Dynamic OEM Table Load:
[ 0.163399] ACPI: SSDT (null) 002A1 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.163540] ACPI: SSDT 7fed882c 004B7 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.163956] ACPI: Dynamic OEM Table Load:
[ 0.163960] ACPI: SSDT (null) 004B7 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.164327] ACPI: SSDT 7fed9016 000E4 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.164761] ACPI: Dynamic OEM Table Load:
[ 0.164765] ACPI: SSDT (null) 000E4 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.164884] ACPI: SSDT 7fed8ce3 00092 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.165302] ACPI: Dynamic OEM Table Load:
[ 0.165305] ACPI: SSDT (null) 00092 (v01 Sony VAIO 20070704 PTL 20050624)
[ 0.368137] ACPI: Interpreter enabled
[ 0.368154] ACPI: (supports S0 S3 S4 S5)
[ 0.368182] ACPI: Using IOAPIC for interrupt routing
[ 0.384670] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 0.390799] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.390995] ACPI: No dock devices found.
[ 0.390999] HEST: Table not found.
[ 0.391005] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.391552] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.392324] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.392327] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.392331] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.392334] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff] (ignored)
[ 0.392337] pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff] (ignored)
[ 0.392340] pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff] (ignored)
[ 0.392344] pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xdfffffff] (ignored)
[ 0.392347] pci_root PNP0A08:00: host bridge window [mem 0xf0000000-0xfebfffff] (ignored)
[ 0.392361] pci 0000:00:00.0: [8086:2a00] type 0 class 0x000600
[ 0.392420] pci 0000:00:01.0: [8086:2a01] type 1 class 0x000604
[ 0.392475] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.392480] pci 0000:00:01.0: PME# disabled
[ 0.392539] pci 0000:00:1a.0: [8086:2834] type 0 class 0x000c03
[ 0.392602] pci 0000:00:1a.0: reg 20: [io 0x1800-0x181f]
[ 0.392651] pci 0000:00:1a.1: [8086:2835] type 0 class 0x000c03
[ 0.392713] pci 0000:00:1a.1: reg 20: [io 0x1820-0x183f]
[ 0.392776] pci 0000:00:1a.7: [8086:283a] type 0 class 0x000c03
[ 0.392804] pci 0000:00:1a.7: reg 10: [mem 0xfc404800-0xfc404bff]
[ 0.392922] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.392928] pci 0000:00:1a.7: PME# disabled
[ 0.392962] pci 0000:00:1b.0: [8086:284b] type 0 class 0x000403
[ 0.392988] pci 0000:00:1b.0: reg 10: [mem 0xfc400000-0xfc403fff 64bit]
[ 0.393105] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.393110] pci 0000:00:1b.0: PME# disabled
[ 0.393143] pci 0000:00:1c.0: [8086:283f] type 1 class 0x000604
[ 0.393266] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.393272] pci 0000:00:1c.0: PME# disabled
[ 0.393308] pci 0000:00:1c.1: [8086:2841] type 1 class 0x000604
[ 0.393431] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.393437] pci 0000:00:1c.1: PME# disabled
[ 0.393473] pci 0000:00:1c.2: [8086:2843] type 1 class 0x000604
[ 0.393595] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.393601] pci 0000:00:1c.2: PME# disabled
[ 0.393639] pci 0000:00:1c.4: [8086:2847] type 1 class 0x000604
[ 0.393761] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.393766] pci 0000:00:1c.4: PME# disabled
[ 0.393802] pci 0000:00:1d.0: [8086:2830] type 0 class 0x000c03
[ 0.393864] pci 0000:00:1d.0: reg 20: [io 0x1840-0x185f]
[ 0.393911] pci 0000:00:1d.1: [8086:2831] type 0 class 0x000c03
[ 0.393974] pci 0000:00:1d.1: reg 20: [io 0x1860-0x187f]
[ 0.394024] pci 0000:00:1d.2: [8086:2832] type 0 class 0x000c03
[ 0.394087] pci 0000:00:1d.2: reg 20: [io 0x1880-0x189f]
[ 0.394149] pci 0000:00:1d.7: [8086:2836] type 0 class 0x000c03
[ 0.394176] pci 0000:00:1d.7: reg 10: [mem 0xfc404c00-0xfc404fff]
[ 0.394294] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.394301] pci 0000:00:1d.7: PME# disabled
[ 0.394327] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
[ 0.394435] pci 0000:00:1f.0: [8086:2815] type 0 class 0x000601
[ 0.394559] pci 0000:00:1f.0: quirk: [io 0x1000-0x107f] claimed by ICH6 ACPI/GPIO/TCO
[ 0.394567] pci 0000:00:1f.0: quirk: [io 0x1180-0x11bf] claimed by ICH6 GPIO
[ 0.394636] pci 0000:00:1f.1: [8086:2850] type 0 class 0x000101
[ 0.394655] pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]
[ 0.394669] pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]
[ 0.394682] pci 0000:00:1f.1: reg 18: [io 0x0000-0x0007]
[ 0.394696] pci 0000:00:1f.1: reg 1c: [io 0x0000-0x0003]
[ 0.394709] pci 0000:00:1f.1: reg 20: [io 0x18a0-0x18af]
[ 0.394769] pci 0000:00:1f.2: [8086:2829] type 0 class 0x000106
[ 0.394799] pci 0000:00:1f.2: reg 10: [io 0x18d8-0x18df]
[ 0.394812] pci 0000:00:1f.2: reg 14: [io 0x18cc-0x18cf]
[ 0.394825] pci 0000:00:1f.2: reg 18: [io 0x18d0-0x18d7]
[ 0.394839] pci 0000:00:1f.2: reg 1c: [io 0x18c8-0x18cb]
[ 0.394852] pci 0000:00:1f.2: reg 20: [io 0x18e0-0x18ff]
[ 0.394866] pci 0000:00:1f.2: reg 24: [mem 0xfc404000-0xfc4047ff]
[ 0.394939] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.394945] pci 0000:00:1f.2: PME# disabled
[ 0.394970] pci 0000:00:1f.3: [8086:283e] type 0 class 0x000c05
[ 0.394989] pci 0000:00:1f.3: reg 10: [mem 0x00000000-0x000000ff]
[ 0.395035] pci 0000:00:1f.3: reg 20: [io 0x1c00-0x1c1f]
[ 0.395168] pci 0000:01:00.0: [10de:0426] type 0 class 0x000300
[ 0.395218] pci 0000:01:00.0: reg 10: [mem 0xce000000-0xceffffff]
[ 0.395269] pci 0000:01:00.0: reg 14: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.395323] pci 0000:01:00.0: reg 1c: [mem 0xcc000000-0xcdffffff 64bit]
[ 0.395359] pci 0000:01:00.0: reg 24: [io 0x2000-0x207f]
[ 0.395394] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.424043] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.424049] pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
[ 0.424053] pci 0000:00:01.0: bridge window [mem 0xcc000000-0xceffffff]
[ 0.424059] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.424132] pci 0000:00:1c.0: PCI bridge to [bus 02-03]
[ 0.424138] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
[ 0.424143] pci 0000:00:1c.0: bridge window [mem 0xf6000000-0xf7ffffff]
[ 0.424152] pci 0000:00:1c.0: bridge window [mem 0xf0000000-0xf1ffffff 64bit pref]