δεν εχω ηχο μετα απο αναβαθμηση απο 11.04 σε 11.10

[Blandar]

Οπος λεει και ο τιτλος δεν εχω ηχο στο λαπτοπ μου

τα χαρακτηρηστικα του ειναι

2 Ubuntu 11.10 oneiric 64bit (el_GR.UTF-8),
3 Intel Celeron CPU 560 2.13GHz ‖ RAM 988 MiB ‖ Hewlett-Packard 30D9 - Hewlett-Packard Compaq Presario C700 Notebook PC
4 Intel Mobile GM965/GL960 Integrated Graphics Controller (primary) [8086:2a02] (rev 03)
5 eth0: Realtek RTL-8139/8139C/8139C+ [10ec:8139] (rev 10) ⋮ wlan0: Atheros Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) [168c:001c] (rev 01)

αποτι ειδα και καταλαβα δεν βρηκε την καρτα ηχου γιατι στις ιδιοτιτες ηχου στην ενοτητα υλικο δεν υπαρχει τπτ

[the_eye]

Δώσε σε τερματικό την εντολή

Κώδικας: Επιλογή όλων

lspci -nn

και δώσε μας το αποτέλεσμα

[Blandar]

Κώδικας: Επιλογή όλων

00:00.0 Host bridge [0600]: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub [8086:2a00] (rev 03)
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (primary) [8086:2a02] (rev 03)
00:02.1 Display controller [0380]: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (secondary) [8086:2a03] (rev 03)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 03)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 [8086:2830] (rev 03)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 [8086:2831] (rev 03)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 [8086:2832] (rev 03)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 [8086:2836] (rev 03)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev f3)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller [8086:2815] (rev 03)
00:1f.1 IDE interface [0101]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller [8086:2850] (rev 03)
00:1f.2 SATA controller [0106]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller [8086:2829] (rev 03)
00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller [8086:283e] (rev 03)
01:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) [168c:001c] (rev 01)
02:01.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)


[the_eye]

Όντως δεν βλέπει κάρτα ήχου !
Για δώσε και το αποτέλεσμα του

Κώδικας: Επιλογή όλων

dmesg

[Blandar]

Κώδικας: Επιλογή όλων

[ 0.959599] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 0.959887] scsi0 : ata_piix
[ 0.959967] scsi1 : ata_piix
[ 0.960330] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x30a0 irq 14
[ 0.960333] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x30a8 irq 15
[ 0.960618] Fixed MDIO Bus: probed
[ 0.960640] PPP generic driver version 2.4.2
[ 0.960703] tun: Universal TUN/TAP device driver, 1.6
[ 0.960705] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.960788] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.960816] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.960841] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.960845] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.960882] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 0.960921] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.964818] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[ 0.965041] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x52400800
[ 0.980015] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.980168] hub 1-0:1.0: USB hub found
[ 0.980173] hub 1-0:1.0: 6 ports detected
[ 0.980243] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.980256] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.980302] uhci_hcd 0000:00:1d.0: PCI INT D -> GSI 21 (level, low) -> IRQ 21
[ 0.980310] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.980314] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.980362] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.980405] uhci_hcd 0000:00:1d.0: irq 21, io base 0x00003080
[ 0.980520] hub 2-0:1.0: USB hub found
[ 0.980524] hub 2-0:1.0: 2 ports detected
[ 0.980586] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 20 (level, low) -> IRQ 20
[ 0.980594] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.980597] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.980629] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 0.980672] uhci_hcd 0000:00:1d.1: irq 20, io base 0x00003060
[ 0.980784] hub 3-0:1.0: USB hub found
[ 0.980788] hub 3-0:1.0: 2 ports detected
[ 0.980842] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[ 0.980849] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.980852] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.980884] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 0.980927] uhci_hcd 0000:00:1d.2: irq 19, io base 0x00003040
[ 0.981047] hub 4-0:1.0: USB hub found
[ 0.981051] hub 4-0:1.0: 2 ports detected
[ 0.981140] i8042: PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 1.011141] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.011146] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.011228] mousedev: PS/2 mouse device common for all mice
[ 1.011385] rtc_cmos 00:03: RTC can wake from S4
[ 1.011500] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.011535] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 1.011647] device-mapper: uevent: version 1.0.3
[ 1.011718] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[ 1.011754] cpuidle: using governor ladder
[ 1.011792] cpuidle: using governor menu
[ 1.011794] EFI Variables Facility v0.08 2004-May-17
[ 1.012036] TCP cubic registered
[ 1.012150] NET: Registered protocol family 10
[ 1.012557] NET: Registered protocol family 17
[ 1.012576] Registering the dns_resolver key type
[ 1.012685] PM: Hibernation image not present or could not be loaded.
[ 1.012697] registered taskstats version 1
[ 1.023368] Magic number: 15:747:647
[ 1.023384] scsi_host host1: hash matches
[ 1.023386] scsi host1: hash matches
[ 1.023460] processor LNXCPU:00: hash matches
[ 1.023503] rtc_cmos 00:03: setting system clock to 2011-10-15 19:38:02 UTC (1318707482)
[ 1.023523] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.023525] EDD information not available.
[ 1.036135] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 1.135636] ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-T40L, KC07, max MWDMA2
[ 1.148282] ata1.00: configured for MWDMA2
[ 1.153818] scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T40L KC07 PQ: 0 ANSI: 5
[ 1.158791] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.158794] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.158909] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 1.158967] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 1.160831] Freeing unused kernel memory: 984k freed
[ 1.161210] Write protecting the kernel read-only data: 10240k
[ 1.161418] Freeing unused kernel memory: 20k freed
[ 1.166411] Freeing unused kernel memory: 1400k freed
[ 1.184257] ACPI: Battery Slot [BAT0] (battery present)
[ 1.189870] udevd[85]: starting version 173
[ 1.404068] usb 1-6: new high speed USB device number 3 using ehci_hcd
[ 1.541024] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 1.541051] 8139cp 0000:02:01.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 1.541564] 8139too: 8139too Fast Ethernet driver 0.9.28
[ 1.541607] 8139too 0000:02:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.541619] 8139too 0000:02:01.0: setting latency timer to 64
[ 1.542801] 8139too 0000:02:01.0: eth0: RealTek RTL8139 at 0x1000, 00:1e:ec:a1:78:79, IRQ 16
[ 1.545369] ahci 0000:00:1f.2: version 3.0
[ 1.545399] ahci 0000:00:1f.2: PCI INT C -> GSI 17 (level, low) -> IRQ 17
[ 1.545455] ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
[ 1.545497] ahci: SSS flag set, parallel bus scan disabled
[ 1.545525] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x1 impl SATA mode
[ 1.545529] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pmp pio slum part ccc ems
[ 1.545535] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.548954] scsi2 : ahci
[ 1.552171] scsi3 : ahci
[ 1.555502] scsi4 : ahci
[ 1.555671] ata3: SATA max UDMA/133 abar m2048@0x52400000 port 0x52400100 irq 41
[ 1.555674] ata4: DUMMY
[ 1.555675] ata5: DUMMY
[ 2.212073] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.212760] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 2.232030] usb 2-1: new full speed USB device number 2 using uhci_hcd
[ 2.527779] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.0/input/input5
[ 2.527993] generic-usb 0003:046D:C52F.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-1/input0
[ 2.532608] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.1/input/input6
[ 2.532985] generic-usb 0003:046D:C52F.0002: input,hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-1/input1
[ 2.533136] usbcore: registered new interface driver usbhid
[ 2.533139] usbhid: USB HID core driver
[ 2.561083] ata3.00: ATA-6: TOSHIBA MK1032GSX, AS021G, max UDMA/100
[ 2.561086] ata3.00: 195371568 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 2.562210] ata3.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 2.562372] ata3.00: configured for UDMA/100
[ 2.562500] scsi 2:0:0:0: Direct-Access ATA TOSHIBA MK1032GS AS02 PQ: 0 ANSI: 5
[ 2.562655] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 2.562762] sd 2:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB)
[ 2.562813] sd 2:0:0:0: [sda] Write Protect is off
[ 2.562817] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.562839] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.646170] sda: sda1 sda2 < sda5 >
[ 2.646469] sd 2:0:0:0: [sda] Attached SCSI disk
[ 3.104260] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 16.984072] udevd[406]: starting version 173
[ 17.049116] Adding 1037308k swap on /dev/sda5. Priority:-1 extents:1 across:1037308k
[ 17.055559] lp: driver loaded but no devices found
[ 17.371292] wmi: Mapper loaded
[ 17.413418] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 17.428813] cfg80211: Calling CRDA to update world regulatory domain
[ 17.503266] [drm] Initialized drm 1.1.0 20060810
[ 17.588565] type=1400 audit(1318707499.061:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=540 comm="apparmor_parser"
[ 17.588833] type=1400 audit(1318707499.061:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=540 comm="apparmor_parser"
[ 17.589006] type=1400 audit(1318707499.061:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=540 comm="apparmor_parser"
[ 17.626416] ath5k 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 17.626433] ath5k 0000:01:00.0: setting latency timer to 64
[ 17.626496] ath5k 0000:01:00.0: registered as 'phy0'
[ 18.144296] Linux video capture interface: v2.00
[ 18.163370] uvcvideo: Found UVC 1.00 device USB2.0 UVC PC Camera (174f:5212)
[ 18.198145] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 18.198152] i915 0000:00:02.0: setting latency timer to 64
[ 18.208323] uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround.
[ 18.276336] usbcore: registered new interface driver uvcvideo
[ 18.276340] USB Video Class driver (v1.1.0)
[ 18.322754] i915 0000:00:02.0: irq 42 for MSI/MSI-X
[ 18.322761] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 18.322763] [drm] Driver supports precise vblank timestamp query.
[ 18.322813] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 18.793797] type=1400 audit(1318707500.265:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm-guest-session-wrapper" pid=710 comm="apparmor_parser"
[ 18.820747] type=1400 audit(1318707500.293:6): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=714 comm="apparmor_parser"
[ 18.821017] type=1400 audit(1318707500.293:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=714 comm="apparmor_parser"
[ 18.821197] type=1400 audit(1318707500.293:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=714 comm="apparmor_parser"
[ 18.866582] type=1400 audit(1318707500.337:9): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=715 comm="apparmor_parser"
[ 18.879170] type=1400 audit(1318707500.349:10): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=715 comm="apparmor_parser"
[ 18.888025] fixme: max PWM is zero.
[ 18.903777] type=1400 audit(1318707500.373:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=715 comm="apparmor_parser"
[ 19.000988] ath: EEPROM regdomain: 0x67
[ 19.000992] ath: EEPROM indicates we should expect a direct regpair map
[ 19.000997] ath: Country alpha2 being used: 00
[ 19.000998] ath: Regpair used: 0x67
[ 19.039784] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
[ 19.039789] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 19.039792] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
[ 19.039795] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 19.039797] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
[ 19.039799] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 19.039801] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
[ 19.039804] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 19.039806] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
[ 19.039809] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 19.039811] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
[ 19.039814] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 19.039816] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
[ 19.039819] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 19.039821] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[ 19.039823] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 19.039825] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[ 19.039828] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 19.039830] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[ 19.039833] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 19.039835] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[ 19.039837] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 19.039840] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
[ 19.039842] cfg80211: 2457000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 19.039844] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
[ 19.039847] cfg80211: 2457000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm)
[ 19.039849] cfg80211: Disabling freq 2484 MHz as custom regd has no rule that fits a 20 MHz wide channel
[ 19.053805] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[ 19.064937] input: HP WMI hotkeys as /devices/virtual/input/input7
[ 19.073235] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 19.080065] Registered led device: ath5k-phy0::rx
[ 19.080110] Registered led device: ath5k-phy0::tx
[ 19.080120] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
[ 19.085601] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[ 19.085606] cfg80211: World regulatory domain updated:
[ 19.085608] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 19.085611] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.085614] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 19.085616] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 19.085619] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.085621] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.174632] [drm] initialized overlay support
[ 19.221786] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 19.243053] 8139too 0000:02:01.0: eth0: link down
[ 19.243296] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.380371] init: failsafe main process (632) killed by TERM signal
[ 19.389552] init: apport pre-start process (803) terminated with status 1
[ 19.426913] init: apport post-stop process (833) terminated with status 1
[ 19.482579] fbcon: inteldrmfb (fb0) is primary device
[ 19.483560] Console: switching to colour frame buffer device 160x50
[ 19.483591] fb0: inteldrmfb frame buffer device
[ 19.483593] drm: registered panic notifier
[ 19.483616] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 19.484489] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 19.541800] acpi device:16: registered as cooling_device1
[ 19.541938] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input8
[ 19.542010] ACPI: Video Device [OVGA] (multi-head: yes rom: no post: no)
[ 19.542064] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 19.738106] ppdev: user-space parallel port driver
[ 19.844310] input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input9
[ 19.880060] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input10
[ 20.140970] Bluetooth: Core ver 2.16
[ 20.141018] NET: Registered protocol family 31
[ 20.141020] Bluetooth: HCI device and connection manager initialized
[ 20.141023] Bluetooth: HCI socket layer initialized
[ 20.141024] Bluetooth: L2CAP socket layer initialized
[ 20.141790] Bluetooth: SCO socket layer initialized
[ 20.152410] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 20.152415] Bluetooth: BNEP filters: protocol multicast
[ 20.301598] Bluetooth: RFCOMM TTY layer initialized
[ 20.301605] Bluetooth: RFCOMM socket layer initialized
[ 20.301607] Bluetooth: RFCOMM ver 1.11
[ 21.297428] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=600
[ 22.568770] wlan0: authenticate with 00:26:44:3e:fd:3c (try 1)
[ 22.570567] wlan0: authenticated
[ 22.570959] wlan0: associate with 00:26:44:3e:fd:3c (try 1)
[ 22.576736] wlan0: RX AssocResp from 00:26:44:3e:fd:3c (capab=0x401 status=0 aid=1)
[ 22.576740] wlan0: associated
[ 22.577379] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 24.463464] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=600
[ 32.632025] wlan0: no IPv6 routers present
[ 65.696722] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[ 267.953868] wlan0: deauthenticating from 00:26:44:3e:fd:3c by local choice (reason=3)
[ 267.954019] cfg80211: All devices are disconnected, going to restore regulatory settings
[ 267.954023] cfg80211: Restoring regulatory settings
[ 267.954028] cfg80211: Calling CRDA to update world regulatory domain
[ 268.441135] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[ 268.441140] cfg80211: World regulatory domain updated:
[ 268.441142] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 268.441145] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 268.441148] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 268.441150] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 268.441153] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 268.441155] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 270.124515] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[ 272.705993] PM: Syncing filesystems ... done.
[ 272.707744] PM: Preparing system for mem sleep
[ 272.820272] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 272.836112] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[ 272.852096] PM: Entering mem sleep
[ 272.852149] Suspending console(s) (use no_console_suspend to debug)
[ 272.852618] sd 2:0:0:0: [sda] Synchronizing SCSI cache
[ 272.883122] ata_piix 0000:00:1f.1: PCI INT B disabled
[ 272.883160] ehci_hcd 0000:00:1d.7: PCI INT A disabled
[ 272.883174] uhci_hcd 0000:00:1d.2: PCI INT C disabled
[ 272.883187] uhci_hcd 0000:00:1d.1: PCI INT B disabled
[ 272.883200] uhci_hcd 0000:00:1d.0: PCI INT D disabled
[ 272.937645] sd 2:0:0:0: [sda] Stopping disk
[ 273.345317] PM: suspend of drv:sd dev:2:0:0:0 complete after 492.707 msecs
[ 273.345326] PM: suspend of drv:scsi dev:target2:0:0 complete after 492.674 msecs
[ 273.345334] PM: suspend of drv:scsi dev:host2 complete after 492.569 msecs
[ 273.360018] PM: suspend of drv:ahci dev:0000:00:1f.2 complete after 476.996 msecs
[ 273.360025] PM: suspend of drv: dev:pci0000:00 complete after 476.124 msecs
[ 273.360030] PM: suspend of devices complete after 507.596 msecs
[ 273.360033] PM: suspend devices took 0.508 seconds
[ 273.392240] PM: late suspend of devices complete after 32.203 msecs
[ 273.392361] ACPI: Preparing to enter system sleep state S3
[ 273.394121] PM: Saving platform NVS memory
[ 273.394560] Disabling non-boot CPUs ...
[ 273.394560] ACPI: Low-level resume complete
[ 273.394560] PM: Restoring platform NVS memory
[ 273.394560] ACPI: Waking up from system sleep state S3
[ 273.396639] i915 0000:00:02.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
[ 273.396647] i915 0000:00:02.0: restoring config space at offset 0x8 (was 0x1, writing 0x30d1)
[ 273.396652] i915 0000:00:02.0: restoring config space at offset 0x6 (was 0xc, writing 0x4000000c)
[ 273.396656] i915 0000:00:02.0: restoring config space at offset 0x4 (was 0x4, writing 0x51000004)
[ 273.396661] i915 0000:00:02.0: restoring config space at offset 0x1 (was 0x900000, writing 0x900407)
[ 273.396713] pcieport 0000:00:1c.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
[ 273.396726] pcieport 0000:00:1c.0: restoring config space at offset 0x9 (was 0x10001, writing 0x50f15001)
[ 273.396732] pcieport 0000:00:1c.0: restoring config space at offset 0x8 (was 0x0, writing 0x52305130)
[ 273.396737] pcieport 0000:00:1c.0: restoring config space at offset 0x7 (was 0x0, writing 0x2020)
[ 273.396743] pcieport 0000:00:1c.0: restoring config space at offset 0x6 (was 0x0, writing 0x10100)
[ 273.396754] pcieport 0000:00:1c.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100407)
[ 273.396821] uhci_hcd 0000:00:1d.0: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
[ 273.396856] uhci_hcd 0000:00:1d.1: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
[ 273.396890] uhci_hcd 0000:00:1d.2: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
[ 273.396935] ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was 0x2900006, writing 0x2900002)
[ 273.396970] pci 0000:00:1e.0: restoring config space at offset 0x9 (was 0x10001, writing 0x1fff1)
[ 273.396975] pci 0000:00:1e.0: restoring config space at offset 0x8 (was 0x0, writing 0x51205120)
[ 273.396981] pci 0000:00:1e.0: restoring config space at offset 0x7 (was 0x22800000, writing 0x22801010)
[ 273.396994] pci 0000:00:1e.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100007)
[ 273.397084] ata_piix 0000:00:1f.1: restoring config space at offset 0x1 (was 0x2800005, writing 0x2880005)
[ 273.397130] ahci 0000:00:1f.2: restoring config space at offset 0x1 (was 0x2b00007, writing 0x2b00407)
[ 273.397219] ath5k 0000:01:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
[ 273.397248] ath5k 0000:01:00.0: restoring config space at offset 0x4 (was 0x4, writing 0x51300004)
[ 273.397254] ath5k 0000:01:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
[ 273.397263] ath5k 0000:01:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100007)
[ 273.397327] 8139too 0000:02:01.0: restoring config space at offset 0x5 (was 0x0, writing 0x51200000)
[ 273.397333] 8139too 0000:02:01.0: restoring config space at offset 0x4 (was 0x1, writing 0x1001)
[ 273.397339] 8139too 0000:02:01.0: restoring config space at offset 0x3 (was 0x0, writing 0x4000)
[ 273.397347] 8139too 0000:02:01.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900007)
[ 273.397891] PM: early resume of devices complete after 1.399 msecs
[ 273.398107] i915 0000:00:02.0: setting latency timer to 64
[ 273.479716] uhci_hcd 0000:00:1d.0: PCI INT D -> GSI 21 (level, low) -> IRQ 21
[ 273.479725] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 273.479755] usb usb2: root hub lost power or was reset
[ 273.479772] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 20 (level, low) -> IRQ 20
[ 273.479779] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 273.479807] usb usb3: root hub lost power or was reset
[ 273.479823] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[ 273.479829] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 273.479857] usb usb4: root hub lost power or was reset
[ 273.479875] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 273.479882] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 273.479952] pci 0000:00:1e.0: setting latency timer to 64
[ 273.479967] ata_piix 0000:00:1f.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 273.479973] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 273.479996] ahci 0000:00:1f.2: setting latency timer to 64
[ 273.482109] sd 2:0:0:0: [sda] Starting disk
[ 273.536596] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 273.536691] PM: resume of drv:i915 dev:0000:00:02.0 complete after 138.590 msecs
[ 273.600122] PM: resume of drv:hub dev:3-0:1.0 complete after 118.368 msecs
[ 273.600129] PM: resume of drv: dev:ep_00 complete after 118.342 msecs
[ 273.600135] PM: resume of drv:hub dev:4-0:1.0 complete after 118.308 msecs
[ 273.600145] PM: resume of drv: dev:ep_00 complete after 118.283 msecs
[ 273.600150] PM: resume of drv: dev:ep_81 complete after 118.381 msecs
[ 273.600155] PM: resume of drv: dev:ep_81 complete after 118.313 msecs
[ 273.647294] PM: resume of drv:hub dev:1-0:1.0 complete after 167.204 msecs
[ 273.647301] PM: resume of drv: dev:ep_00 complete after 166.638 msecs
[ 273.647323] PM: resume of drv: dev:ep_81 complete after 166.664 msecs
[ 273.652127] PM: resume of drv:battery dev:PNP0C0A:00 complete after 170.485 msecs
[ 273.704074] PM: resume of drv:hub dev:2-0:1.0 complete after 222.412 msecs
[ 273.704082] PM: resume of drv: dev:ep_00 complete after 222.370 msecs
[ 273.704098] PM: resume of drv: dev:ep_81 complete after 222.405 msecs
[ 273.756064] usb 1-6: reset high speed USB device number 3 using ehci_hcd
[ 273.768039] PM: resume of drv:ac dev:ACPI0003:00 complete after 115.905 msecs
[ 273.924403] ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 273.924407] ata1.00: ACPI cmd ef/03:22:00:00:00:a0 (SET FEATURES) filtered out
[ 273.940261] ata1.00: configured for MWDMA2
[ 274.032036] usb 2-1: reset full speed USB device number 2 using uhci_hcd
[ 274.187704] PM: resume of drv:usbhid dev:2-1:1.0 complete after 705.690 msecs
[ 274.187713] PM: resume of drv:usbhid dev:2-1:1.1 complete after 705.664 msecs
[ 274.187719] PM: resume of drv: dev:ep_00 complete after 705.634 msecs
[ 274.187725] PM: resume of drv: dev:ep_81 complete after 705.695 msecs
[ 274.187730] PM: resume of drv: dev:ep_82 complete after 705.665 msecs
[ 274.187736] PM: resume of drv:generic-usb dev:0003:046D:C52F.0001 complete after 386.610 msecs
[ 275.764036] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 275.764962] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 275.766254] ata3.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 275.766455] ata3.00: configured for UDMA/100
[ 275.790755] PM: resume of drv:sd dev:2:0:0:0 complete after 2308.647 msecs
[ 275.790766] PM: resume of drv:scsi_device dev:2:0:0:0 complete after 2308.615 msecs
[ 275.790772] PM: resume of drv:scsi_disk dev:2:0:0:0 complete after 1602.995 msecs
[ 279.236137] uvcvideo: Failed to set UVC commit control : -110 (exp. 26).
[ 279.236143] uvcvideo 1-6:1.1: reset_resume error -5
[ 279.236156] PM: resume of drv:uvcvideo dev:1-6:1.0 complete after 5754.228 msecs
[ 279.236164] PM: resume of drv:uvcvideo dev:1-6:1.1 complete after 5754.202 msecs
[ 279.236170] PM: resume of drv: dev:ep_00 complete after 5754.191 msecs
[ 279.236176] PM: resume of drv: dev:ep_83 complete after 5754.230 msecs
[ 279.236182] PM: resume of drv:video4linux dev:video0 complete after 3445.367 msecs
[ 279.237427] PM: resume of devices complete after 5839.468 msecs
[ 279.237547] PM: resume devices took 5.840 seconds
[ 279.237579] PM: Finishing wakeup.
[ 279.237580] Restarting tasks ... done.
[ 279.379401] video LNXVIDEO:00: Restoring backlight state
[ 281.201511] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[ 281.380282] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 281.384341] 8139too 0000:02:01.0: eth0: link down
[ 281.384581] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 284.166269] wlan0: authenticate with 00:26:44:3e:fd:3c (try 1)
[ 284.168256] wlan0: authenticated
[ 284.169536] wlan0: associate with 00:26:44:3e:fd:3c (try 1)
[ 284.174963] wlan0: RX AssocResp from 00:26:44:3e:fd:3c (capab=0x401 status=0 aid=1)
[ 284.174967] wlan0: associated
[ 284.175730] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 295.208060] wlan0: no IPv6 routers present

[Blandar]

Τελικα εχει καει η καρτα ηχου. Παρακαλω να σβηστη το θεμα