ΠΡΟΒΛΗΜΑ ΜΕ ΤΗΝ ΚΑΡΤΑ ΗΧΟΥ IntelCorporation 82801I ΕΠΙΛΥΘΗΚΕ

[xdgr2001]

Αντιμετωπίζω το εξής περίεργο πρόβλημα. Οταν ανοίγω τον υπολογιστή και ξεκινήσω να αν;απαράγω κάποιο κομάτι ήχου , πχ ενα αρχείο mp3, ο ήχος ακούγετε κανονικά. Αν όμως δεν κάνω αναπαραγωγή μουσικών κομματιών ή γενικά δεν χρησιμοποιώ ήχο, τότε αν μετα απο 10-20 min προσπαθήσω να κάνω αναπαραγωγή ενός μουσικού αρχείου ή μιας ταινίας ο ήχος δεν ακούγετε απο τα ηχεία και πρέπει να κάνω επανεκίνηση του συστήματος για να λυθεί το πρόβλημα.

Σας παραθέτω και τα αποτελεσματα των εντολων lspci -nn

Κώδικας: Επιλογή όλων

00:00.0 Host bridge [0600]: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller [8086:29c0] (rev 02)
00:01.0 PCI bridge [0604]: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port [8086:29c1] (rev 02)
00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 02)
00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 02)
00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 02)
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 02)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 02)
00:1c.3 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 [8086:2946] (rev 02)
00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 02)
00:1c.5 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 [8086:294a] (rev 02)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 02)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 02)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 02)
00:1d.3 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 02)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 02)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 92)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801IR (ICH9R) LPC Interface Controller [8086:2916] (rev 02)
00:1f.2 IDE interface [0101]: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 4 port SATA IDE Controller [8086:2920] (rev 02)
00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller [8086:2930] (rev 02)
00:1f.5 IDE interface [0101]: Intel Corporation 82801I (ICH9 Family) 2 port SATA IDE Controller [8086:2926] (rev 02)
01:00.0 VGA compatible controller [0300]: nVidia Corporation GeForce 8500 GT [10de:0421] (rev a1)
03:00.0 PCI bridge [0604]: Creative Labs Device [1102:7006]
04:00.0 Audio device [0403]: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG [1102:0009]
05:00.0 IDE interface [0101]: Marvell Technology Group Ltd. 88SE6121 SATA II Controller [11ab:6121] (rev b2)
06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01)
07:00.0 PCI bridge [0604]: Intel Corporation 21152 PCI-to-PCI Bridge [8086:b152]
07:07.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306 Fire II IEEE 1394 OHCI Link Layer Controller [1106:3044] (rev c0)
08:04.0 Multimedia controller [0480]: Philips Semiconductors SAA7146 [1131:7146] (rev 01)
08:08.0 Multimedia controller [0480]: C-Cube Microsystems E4? [123f:8120] (rev b1)
08:0c.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB12LV26 IEEE-1394 Controller (Link) [104c:8020]


και asoundconf list

Κώδικας: Επιλογή όλων

Names of available sound cards:
Intel
default


και επισης έχω τρέξει μέασα απο το τερματικό την εντολή asoundconf set-default-card Intel

Ευχαριστώ πολύ

[logari81]

αφου περιμένεις να εμφανιστει το προβλημα τρεξε:

Κώδικας: Επιλογή όλων

dmesg

και ποσταρε και το αποτελεσμα εδω μεσα σε

Κώδικας: Επιλογή όλων

[code][/code]

επίσης βλεπω οτι εχεις συνδεμενη μια καρτα τηλεόρασης, δοκιμασε να την αφαιρεσεις για να δεις αν επηρεάζει.

[simosx]

Δώσε περισσότερες πληροφορίες για την κάρτα ήχου σύμφωνα με τις οδηγίες στο
viewtopic.php?f=9&t=7242&p=75862

[pros]

αφου περιμένεις να εμφανιστει το προβλημα τρεξε:

Κώδικας: Επιλογή όλων

dmesg

και ποσταρε και το αποτελεσμα εδω μεσα σε

Κώδικας: Επιλογή όλων

[code][/code]

επίσης βλεπω οτι εχεις συνδεμενη μια καρτα τηλεόρασης, δοκιμασε να την αφαιρεσεις για να δεις αν επηρεάζει.

Κώδικας: Επιλογή όλων

[ 0.400036] AppArmor: AppArmor Filesystem Enabled
[ 0.408006] pnp: PnP ACPI init
[ 0.408011] ACPI: bus type pnp registered
[ 0.410626] pnp: PnP ACPI: found 15 devices
[ 0.410627] ACPI: ACPI bus type pnp unregistered
[ 0.410630] PnPBIOS: Disabled by ACPI PNP
[ 0.410636] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
[ 0.410641] system 00:08: ioport range 0xa10-0xaef has been reserved
[ 0.410643] system 00:08: ioport range 0xae0-0xaef has been reserved
[ 0.410647] system 00:09: ioport range 0x4d0-0x4d1 has been reserved
[ 0.410648] system 00:09: ioport range 0x800-0x87f has been reserved
[ 0.410650] system 00:09: ioport range 0x480-0x4bf has been reserved
[ 0.410652] system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.410654] system 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved
[ 0.410657] system 00:0b: iomem range 0xffc00000-0xffefffff has been reserved
[ 0.410663] system 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
[ 0.410665] system 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.410668] system 00:0d: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.410672] system 00:0e: iomem range 0x0-0x9ffff could not be reserved
[ 0.410674] system 00:0e: iomem range 0xc0000-0xcffff could not be reserved
[ 0.410675] system 00:0e: iomem range 0xe0000-0xfffff could not be reserved
[ 0.410677] system 00:0e: iomem range 0x100000-0x7fffffff could not be reserved
[ 0.445310] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.445312] pci 0000:00:01.0: IO window: 0xb000-0xbfff
[ 0.445315] pci 0000:00:01.0: MEM window: 0xfa000000-0xfe6fffff
[ 0.445317] pci 0000:00:01.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
[ 0.445320] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.445321] pci 0000:00:1c.0: IO window: disabled
[ 0.445325] pci 0000:00:1c.0: MEM window: disabled
[ 0.445328] pci 0000:00:1c.0: PREFETCH window: disabled
[ 0.445332] pci 0000:03:00.0: PCI bridge, secondary bus 0000:04
[ 0.445333] pci 0000:03:00.0: IO window: disabled
[ 0.445339] pci 0000:03:00.0: MEM window: 0xfe700000-0xfe7fffff
[ 0.445343] pci 0000:03:00.0: PREFETCH window: disabled
[ 0.445351] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:03
[ 0.445352] pci 0000:00:1c.3: IO window: disabled
[ 0.445355] pci 0000:00:1c.3: MEM window: 0xfe700000-0xfe7fffff
[ 0.445358] pci 0000:00:1c.3: PREFETCH window: disabled
[ 0.445362] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:05
[ 0.445364] pci 0000:00:1c.4: IO window: 0xc000-0xcfff
[ 0.445368] pci 0000:00:1c.4: MEM window: 0xfe800000-0xfe8fffff
[ 0.445371] pci 0000:00:1c.4: PREFETCH window: disabled
[ 0.445375] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:06
[ 0.445377] pci 0000:00:1c.5: IO window: 0xd000-0xdfff
[ 0.445380] pci 0000:00:1c.5: MEM window: 0xfe900000-0xfe9fffff
[ 0.445383] pci 0000:00:1c.5: PREFETCH window: disabled
[ 0.445388] pci 0000:07:00.0: PCI bridge, secondary bus 0000:08
[ 0.445389] pci 0000:07:00.0: IO window: disabled
[ 0.445393] pci 0000:07:00.0: MEM window: 0xfeb00000-0xfebfffff
[ 0.445397] pci 0000:07:00.0: PREFETCH window: 0x000000f8000000-0x000000f8ffffff
[ 0.445402] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:07
[ 0.445404] pci 0000:00:1e.0: IO window: 0xe000-0xefff
[ 0.445408] pci 0000:00:1e.0: MEM window: 0xfea00000-0xfebfffff
[ 0.445411] pci 0000:00:1e.0: PREFETCH window: 0x000000f8000000-0x000000f8ffffff
[ 0.445419] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.445422] pci 0000:00:01.0: setting latency timer to 64
[ 0.445427] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.445430] pci 0000:00:1c.0: setting latency timer to 64
[ 0.445435] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.445438] pci 0000:00:1c.3: setting latency timer to 64
[ 0.445448] pci 0000:03:00.0: setting latency timer to 64
[ 0.445454] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.445457] pci 0000:00:1c.4: setting latency timer to 64
[ 0.445461] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.445464] pci 0000:00:1c.5: setting latency timer to 64
[ 0.445469] pci 0000:00:1e.0: setting latency timer to 64
[ 0.445477] bus: 00 index 0 io port: [0x00-0xffff]
[ 0.445478] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[ 0.445480] bus: 01 index 0 io port: [0xb000-0xbfff]
[ 0.445481] bus: 01 index 1 mmio: [0xfa000000-0xfe6fffff]
[ 0.445483] bus: 01 index 2 mmio: [0xd0000000-0xdfffffff]
[ 0.445484] bus: 01 index 3 mmio: [0x0-0x0]
[ 0.445485] bus: 02 index 0 mmio: [0x0-0x0]
[ 0.445486] bus: 02 index 1 mmio: [0x0-0x0]
[ 0.445487] bus: 02 index 2 mmio: [0x0-0x0]
[ 0.445488] bus: 02 index 3 mmio: [0x0-0x0]
[ 0.445490] bus: 03 index 0 mmio: [0x0-0x0]
[ 0.445491] bus: 03 index 1 mmio: [0xfe700000-0xfe7fffff]
[ 0.445492] bus: 03 index 2 mmio: [0x0-0x0]
[ 0.445493] bus: 03 index 3 mmio: [0x0-0x0]
[ 0.445494] bus: 04 index 0 mmio: [0x0-0x0]
[ 0.445496] bus: 04 index 1 mmio: [0xfe700000-0xfe7fffff]
[ 0.445497] bus: 04 index 2 mmio: [0x0-0x0]
[ 0.445498] bus: 04 index 3 mmio: [0x0-0x0]
[ 0.445499] bus: 05 index 0 io port: [0xc000-0xcfff]
[ 0.445501] bus: 05 index 1 mmio: [0xfe800000-0xfe8fffff]
[ 0.445502] bus: 05 index 2 mmio: [0x0-0x0]
[ 0.445503] bus: 05 index 3 mmio: [0x0-0x0]
[ 0.445504] bus: 06 index 0 io port: [0xd000-0xdfff]
[ 0.445506] bus: 06 index 1 mmio: [0xfe900000-0xfe9fffff]
[ 0.445507] bus: 06 index 2 mmio: [0x0-0x0]
[ 0.445508] bus: 06 index 3 mmio: [0x0-0x0]
[ 0.445509] bus: 07 index 0 io port: [0xe000-0xefff]
[ 0.445511] bus: 07 index 1 mmio: [0xfea00000-0xfebfffff]
[ 0.445512] bus: 07 index 2 mmio: [0xf8000000-0xf8ffffff]
[ 0.445513] bus: 07 index 3 io port: [0x00-0xffff]
[ 0.445515] bus: 07 index 4 mmio: [0x000000-0xffffffff]
[ 0.445516] bus: 08 index 0 mmio: [0x0-0x0]
[ 0.445517] bus: 08 index 1 mmio: [0xfeb00000-0xfebfffff]
[ 0.445518] bus: 08 index 2 mmio: [0xf8000000-0xf8ffffff]
[ 0.445520] bus: 08 index 3 mmio: [0x0-0x0]
[ 0.445525] NET: Registered protocol family 2
[ 0.460041] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.460729] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.460940] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.461043] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.461045] TCP reno registered
[ 0.468055] NET: Registered protocol family 1
[ 0.468125] checking if image is initramfs... it is
[ 0.890003] Freeing initrd memory: 7292k freed
[ 0.890140] cpufreq: No nForce2 chipset.
[ 0.890231] audit: initializing netlink socket (disabled)
[ 0.890245] type=2000 audit(1256162465.889:1): initialized
[ 0.894919] highmem bounce pool size: 64 pages
[ 0.894923] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.895755] VFS: Disk quotas dquot_6.5.1
[ 0.895791] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.896166] fuse init (API version 7.10)
[ 0.896220] msgmni has been set to 1698
[ 0.896330] alg: No test for stdrng (krng)
[ 0.896336] io scheduler noop registered
[ 0.896338] io scheduler anticipatory registered
[ 0.896339] io scheduler deadline registered
[ 0.896347] io scheduler cfq registered (default)
[ 0.896468] pci 0000:01:00.0: Boot video device
[ 0.897850] Switched to high resolution mode on CPU 1
[ 0.898912] pcieport-driver 0000:00:01.0: setting latency timer to 64
[ 0.898934] pcieport-driver 0000:00:01.0: found MSI capability
[ 0.898950] pcieport-driver 0000:00:01.0: irq 2303 for MSI/MSI-X
[ 0.898956] pci_express 0000:00:01.0:pcie00: allocate port service
[ 0.898965] pci_express 0000:00:01.0:pcie03: allocate port service
[ 0.898995] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 0.899020] pcieport-driver 0000:00:1c.0: found MSI capability
[ 0.899038] pcieport-driver 0000:00:1c.0: irq 2302 for MSI/MSI-X
[ 0.899046] pci_express 0000:00:1c.0:pcie00: allocate port service
[ 0.899053] pci_express 0000:00:1c.0:pcie02: allocate port service
[ 0.899061] pci_express 0000:00:1c.0:pcie03: allocate port service
[ 0.899099] pcieport-driver 0000:00:1c.3: setting latency timer to 64
[ 0.899124] pcieport-driver 0000:00:1c.3: found MSI capability
[ 0.899141] pcieport-driver 0000:00:1c.3: irq 2301 for MSI/MSI-X
[ 0.899149] pci_express 0000:00:1c.3:pcie00: allocate port service
[ 0.899157] pci_express 0000:00:1c.3:pcie02: allocate port service
[ 0.899166] pci_express 0000:00:1c.3:pcie03: allocate port service
[ 0.899205] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[ 0.899230] pcieport-driver 0000:00:1c.4: found MSI capability
[ 0.899247] pcieport-driver 0000:00:1c.4: irq 2300 for MSI/MSI-X
[ 0.899255] pci_express 0000:00:1c.4:pcie00: allocate port service
[ 0.899263] pci_express 0000:00:1c.4:pcie02: allocate port service
[ 0.899270] pci_express 0000:00:1c.4:pcie03: allocate port service
[ 0.899309] pcieport-driver 0000:00:1c.5: setting latency timer to 64
[ 0.899334] pcieport-driver 0000:00:1c.5: found MSI capability
[ 0.899351] pcieport-driver 0000:00:1c.5: irq 2299 for MSI/MSI-X
[ 0.899359] pci_express 0000:00:1c.5:pcie00: allocate port service
[ 0.899367] pci_express 0000:00:1c.5:pcie02: allocate port service
[ 0.899374] pci_express 0000:00:1c.5:pcie03: allocate port service
[ 0.899448] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.899927] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.900019] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 0.900021] ACPI: Power Button (FF) [PWRF]
[ 0.900054] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 0.900055] ACPI: Power Button (CM) [PWRB]
[ 0.900229] processor ACPI_CPU:00: registered as cooling_device0
[ 0.900253] processor ACPI_CPU:01: registered as cooling_device1
[ 0.901320] Switched to high resolution mode on CPU 0
[ 0.901907] isapnp: Scanning for PnP cards...
[ 1.254723] isapnp: No Plug & Play device found
[ 1.260573] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 1.260649] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.260892] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.261411] brd: module loaded
[ 1.261601] loop: module loaded
[ 1.261641] Fixed MDIO Bus: probed
[ 1.261644] PPP generic driver version 2.4.2
[ 1.261677] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 1.261694] Driver 'sd' needs updating - please use bus_type methods
[ 1.261700] Driver 'sr' needs updating - please use bus_type methods
[ 1.261726] ahci 0000:05:00.0: version 3.0
[ 1.261755] ata_piix 0000:00:1f.2: version 2.12
[ 1.261762] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.261766] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 1.261797] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 1.261836] scsi0 : ata_piix
[ 1.261880] scsi1 : ata_piix
[ 1.262826] ata1: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 19
[ 1.262829] ata2: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 19
[ 2.056058] ata1.00: SATA link down (SStatus 0 SControl 300)
[ 2.056067] ata1.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.083414] ata1.01: ATA-7: WDC WD7500AAKS-00RBA0, 30.04G30, max UDMA/133
[ 2.083415] ata1.01: 1465149168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 2.096924] ata1.01: configured for UDMA/133
[ 2.892057] ata2.00: SATA link down (SStatus 0 SControl 300)
[ 2.892065] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.922641] ata2.01: ATA-7: WDC WD5000KS-00MNB0, 07.02E07, max UDMA/133
[ 2.922643] ata2.01: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 2.936380] ata2.01: configured for UDMA/133
[ 2.936445] scsi 0:0:1:0: Direct-Access ATA WDC WD7500AAKS-0 30.0 PQ: 0 ANSI: 5
[ 2.936506] sd 0:0:1:0: [sda] 1465149168 512-byte hardware sectors: (750 GB/698 GiB)
[ 2.936517] sd 0:0:1:0: [sda] Write Protect is off
[ 2.936518] sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
[ 2.936534] sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.936570] sd 0:0:1:0: [sda] 1465149168 512-byte hardware sectors: (750 GB/698 GiB)
[ 2.936579] sd 0:0:1:0: [sda] Write Protect is off
[ 2.936581] sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
[ 2.936596] sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.936598] sda: sda3 sda4
[ 2.944259] sd 0:0:1:0: [sda] Attached SCSI disk
[ 2.944284] sd 0:0:1:0: Attached scsi generic sg0 type 0
[ 2.944327] scsi 1:0:1:0: Direct-Access ATA WDC WD5000KS-00M 07.0 PQ: 0 ANSI: 5
[ 2.944378] sd 1:0:1:0: [sdb] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
[ 2.944388] sd 1:0:1:0: [sdb] Write Protect is off
[ 2.944389] sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 2.944404] sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.944435] sd 1:0:1:0: [sdb] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
[ 2.944444] sd 1:0:1:0: [sdb] Write Protect is off
[ 2.944446] sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 2.944461] sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.944463] sdb: sdb1
[ 2.954228] sd 1:0:1:0: [sdb] Attached SCSI disk
[ 2.954250] sd 1:0:1:0: Attached scsi generic sg1 type 0
[ 2.954261] ata_piix 0000:00:1f.5: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.954264] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[ 2.954290] ata_piix 0000:00:1f.5: setting latency timer to 64
[ 2.954317] scsi2 : ata_piix
[ 2.954352] scsi3 : ata_piix
[ 2.955276] ata3: SATA max UDMA/133 cmd 0x9000 ctl 0x8c00 bmdma 0x8480 irq 19
[ 2.955278] ata4: SATA max UDMA/133 cmd 0x8880 ctl 0x8800 bmdma 0x8488 irq 19
[ 3.428037] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3.436268] ata3.00: ATA-7: ST3400832AS, 3.01, max UDMA/133
[ 3.436269] ata3.00: 781422768 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 3.444277] ata3.00: configured for UDMA/133
[ 3.920038] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.941532] ata4.00: ATA-8: WDC WD10EACS-00ZJB0, 01.01B01, max UDMA/133
[ 3.941533] ata4.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 3.956620] ata4.00: configured for UDMA/133
[ 3.956669] scsi 2:0:0:0: Direct-Access ATA ST3400832AS 3.01 PQ: 0 ANSI: 5
[ 3.956721] sd 2:0:0:0: [sdc] 781422768 512-byte hardware sectors: (400 GB/372 GiB)
[ 3.956730] sd 2:0:0:0: [sdc] Write Protect is off
[ 3.956732] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 3.956747] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.956778] sd 2:0:0:0: [sdc] 781422768 512-byte hardware sectors: (400 GB/372 GiB)
[ 3.956786] sd 2:0:0:0: [sdc] Write Protect is off
[ 3.956788] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 3.956803] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.956805] sdc: sdc1 sdc2 sdc3
[ 3.987807] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 3.987828] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 3.987871] scsi 3:0:0:0: Direct-Access ATA WDC WD10EACS-00Z 01.0 PQ: 0 ANSI: 5
[ 3.987920] sd 3:0:0:0: [sdd] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
[ 3.987929] sd 3:0:0:0: [sdd] Write Protect is off
[ 3.987930] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 3.987946] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.987977] sd 3:0:0:0: [sdd] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
[ 3.987986] sd 3:0:0:0: [sdd] Write Protect is off
[ 3.987987] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 3.988008] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.988010] sdd: sdd1
[ 3.997739] sd 3:0:0:0: [sdd] Attached SCSI disk
[ 3.997762] sd 3:0:0:0: Attached scsi generic sg3 type 0
[ 3.998050] pata_marvell 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.998068] pata_marvell 0000:05:00.0: setting latency timer to 64
[ 3.998107] scsi4 : pata_marvell
[ 3.998141] scsi5 : pata_marvell
[ 3.998162] ata5: PATA max UDMA/100 cmd 0xcc00 ctl 0xc880 bmdma 0xc400 irq 16
[ 3.998163] ata6: PATA max UDMA/133 cmd 0xc800 ctl 0xc480 bmdma 0xc408 irq 16
[ 4.168376] ata5.01: ATAPI: PIONEER DVD-RW DVR-112D, 1.21, max UDMA/66
[ 4.184388] ata5.01: configured for UDMA/66
[ 4.361543] scsi 4:0:1:0: CD-ROM PIONEER DVD-RW DVR-112D 1.21 PQ: 0 ANSI: 5
[ 4.379778] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 4.379780] Uniform CD-ROM driver Revision: 3.20
[ 4.379831] sr 4:0:1:0: Attached scsi CD-ROM sr0
[ 4.379857] sr 4:0:1:0: Attached scsi generic sg4 type 5
[ 4.380020] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.380032] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 4.380044] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 4.380047] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 4.380079] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 4.383964] ehci_hcd 0000:00:1a.7: debug port 1
[ 4.383968] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 4.383977] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf9fffc00
[ 4.396007] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 4.396053] usb usb1: configuration #1 chosen from 1 choice
[ 4.396069] hub 1-0:1.0: USB hub found
[ 4.396074] hub 1-0:1.0: 4 ports detected
[ 4.396137] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 4.396143] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 4.396146] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 4.396178] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 4.400079] ehci_hcd 0000:00:1d.7: debug port 1
[ 4.400083] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 4.400092] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9fff800
[ 4.412006] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 4.412040] usb usb2: configuration #1 chosen from 1 choice
[ 4.412054] hub 2-0:1.0: USB hub found
[ 4.412058] hub 2-0:1.0: 8 ports detected
[ 4.412120] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.412131] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.412142] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.412146] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 4.412148] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 4.412174] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 4.412192] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ac00
[ 4.412235] usb usb3: configuration #1 chosen from 1 choice
[ 4.412250] hub 3-0:1.0: USB hub found
[ 4.412254] hub 3-0:1.0: 2 ports detected
[ 4.412304] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 4.412308] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 4.412310] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 4.412333] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 4.412356] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000a880
[ 4.412398] usb usb4: configuration #1 chosen from 1 choice
[ 4.412414] hub 4-0:1.0: USB hub found
[ 4.412417] hub 4-0:1.0: 2 ports detected
[ 4.412466] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 4.412470] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 4.412472] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 4.412496] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 4.412518] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000a800
[ 4.412562] usb usb5: configuration #1 chosen from 1 choice
[ 4.412577] hub 5-0:1.0: USB hub found
[ 4.412582] hub 5-0:1.0: 2 ports detected
[ 4.412632] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 4.412636] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 4.412638] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 4.412662] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 4.412679] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000a480
[ 4.412722] usb usb6: configuration #1 chosen from 1 choice
[ 4.412737] hub 6-0:1.0: USB hub found
[ 4.412740] hub 6-0:1.0: 2 ports detected
[ 4.412791] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 4.412795] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 4.412797] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 4.412824] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 4.412842] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a400
[ 4.412885] usb usb7: configuration #1 chosen from 1 choice
[ 4.412900] hub 7-0:1.0: USB hub found
[ 4.412903] hub 7-0:1.0: 2 ports detected
[ 4.412952] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 4.412956] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 4.412958] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 4.412985] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 8
[ 4.413002] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000a080
[ 4.413045] usb usb8: configuration #1 chosen from 1 choice
[ 4.413060] hub 8-0:1.0: USB hub found
[ 4.413063] hub 8-0:1.0: 2 ports detected
[ 4.413152] PNP: No PS/2 controller found. Probing ports directly.
[ 4.415204] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 4.415207] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 4.416526] mice: PS/2 mouse device common for all mice
[ 4.428544] rtc_cmos 00:03: RTC can wake from S4
[ 4.428563] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 4.428582] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 4.428618] device-mapper: uevent: version 1.0.3
[ 4.428671] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 4.428715] device-mapper: multipath: version 1.0.5 loaded
[ 4.428717] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 4.428762] EISA: Probing bus 0 at eisa.0
[ 4.428781] Cannot allocate resource for EISA slot 8
[ 4.428782] EISA: Detected 0 cards.
[ 4.428810] cpuidle: using governor ladder
[ 4.428812] cpuidle: using governor menu
[ 4.429125] TCP cubic registered
[ 4.429181] NET: Registered protocol family 10
[ 4.429450] lo: Disabled Privacy Extensions
[ 4.429658] NET: Registered protocol family 17
[ 4.429668] Bluetooth: L2CAP ver 2.11
[ 4.429669] Bluetooth: L2CAP socket layer initialized
[ 4.429671] Bluetooth: SCO (Voice Link) ver 0.6
[ 4.429672] Bluetooth: SCO socket layer initialized
[ 4.429689] Bluetooth: RFCOMM socket layer initialized
[ 4.429693] Bluetooth: RFCOMM TTY layer initialized
[ 4.429694] Bluetooth: RFCOMM ver 1.10
[ 4.429727] Using IPI No-Shortcut mode
[ 4.429768] registered taskstats version 1
[ 4.429862] Magic number: 13:897:47
[ 4.429903] rtc_cmos 00:03: setting system clock to 2009-10-21 22:01:10 UTC (1256162470)
[ 4.429905] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 4.429906] EDD information not available.
[ 4.430050] Freeing unused kernel memory: 532k freed
[ 4.430125] Write protecting the kernel text: 4112k
[ 4.430152] Write protecting the kernel read-only data: 1524k
[ 4.591247] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 4.591263] r8169 0000:06:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 4.591280] r8169 0000:06:00.0: setting latency timer to 64
[ 4.591392] r8169 0000:06:00.0: irq 2298 for MSI/MSI-X
[ 4.591803] eth0: RTL8168b/8111b at 0xf7c5e000, 00:19:db:f8:0f:73, XID 38000000 IRQ 2298
[ 4.685645] Floppy drive(s): fd0 is 1.44M
[ 4.708553] FDC 0 is a post-1991 82077
[ 4.729632] ohci1394 0000:07:07.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 4.781371] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 4.782409] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[feaff800-feafffff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 4.800741] ohci1394 0000:08:0c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.851449] ohci1394: fw-host1: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[febff000-febff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 5.138536] PM: Starting manual resume from disk
[ 5.138538] PM: Resume from partition 8:34
[ 5.138539] PM: Checking hibernation image.
[ 5.138684] PM: Resume from disk failed.
[ 5.166154] usb 1-1: configuration #1 chosen from 1 choice
[ 5.560008] usb 2-2: new high speed USB device using ehci_hcd and address 2
[ 6.047085] usb 2-2: configuration #1 chosen from 1 choice
[ 6.072072] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc00012e404a]
[ 6.196070] ieee1394: Host added: ID:BUS[1-00:1023] GUID[00308d0a0157b411]
[ 6.268010] usb 2-7: new high speed USB device using ehci_hcd and address 4
[ 6.409615] usb 2-7: configuration #1 chosen from 1 choice
[ 6.760507] usb 3-2: new full speed USB device using uhci_hcd and address 2
[ 6.958474] usb 3-2: configuration #1 chosen from 1 choice
[ 7.200507] usb 4-1: new low speed USB device using uhci_hcd and address 2
[ 7.384665] usb 4-1: configuration #1 chosen from 1 choice
[ 7.624508] usb 4-2: new full speed USB device using uhci_hcd and address 3
[ 7.808705] usb 4-2: configuration #1 chosen from 1 choice
[ 8.048010] usb 6-2: new full speed USB device using uhci_hcd and address 2
[ 8.206399] usb 6-2: configuration #1 chosen from 1 choice
[ 8.448007] usb 8-2: new full speed USB device using uhci_hcd and address 2
[ 8.631435] usb 8-2: configuration #1 chosen from 1 choice
[ 11.336012] udev: starting version 141
[ 11.839588] cfg80211: Calling CRDA to update world regulatory domain
[ 12.206812] cfg80211: World regulatory domain updated:
[ 12.206815] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.206816] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.206818] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.206819] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.206821] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.206822] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.231388] Linux agpgart interface v0.103
[ 12.238912] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 12.536592] nvidia: module license 'NVIDIA' taints kernel.
[ 12.787835] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 12.787840] nvidia 0000:01:00.0: setting latency timer to 64
[ 12.788518] NVRM: loading NVIDIA UNIX x86 Kernel Module 180.44 Mon Mar 23 14:59:10 PST 2009
[ 12.873650] usbcore: registered new interface driver hiddev
[ 12.875024] usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0xB402
[ 12.875039] usbcore: registered new interface driver usblp
[ 12.879818] Initializing USB Mass Storage driver...
[ 12.879886] scsi6 : SCSI emulation for USB Mass Storage devices
[ 12.880065] usb-storage: device found at 2
[ 12.880066] usb-storage: waiting for device to settle before scanning
[ 12.880090] scsi7 : SCSI emulation for USB Mass Storage devices
[ 12.880179] usbcore: registered new interface driver usb-storage
[ 12.881087] USB Mass Storage support registered.
[ 12.881089] usb-storage: device found at 2
[ 12.881090] usb-storage: waiting for device to settle before scanning
[ 12.886653] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 12.887321] input: Microsft Microsoft Wireless Desktop Receiver 3.1A as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.0/input/input4
[ 12.887516] iTCO_vendor_support: vendor-support=0
[ 12.896259] generic-usb 0003:045E:00F1.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsft Microsoft Wireless Desktop Receiver 3.1A] on usb-0000:00:1a.1-1/input0
[ 12.909597] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 12.909703] iTCO_wdt: Found a ICH9R TCO device (Version=2, TCOBASE=0x0860)
[ 12.909779] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 13.030006] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 13.030044] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 13.032265] input: Microsft Microsoft Wireless Desktop Receiver 3.1A as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.1/input/input5
[ 13.037491] generic-usb 0003:045E:00F1.0002: input,hidraw1: USB HID v1.11 Mouse [Microsft Microsoft Wireless Desktop Receiver 3.1A] on usb-0000:00:1a.1-1/input1
[ 13.042831] input: Thrustmaster Run'N' Drive as /devices/pci0000:00/0000:00:1d.1/usb6/6-2/6-2:1.0/input/input6
[ 13.046504] generic-usb 0003:044F:D003.0003: input,hidraw2: USB HID v1.00 Gamepad [Thrustmaster Run'N' Drive] on usb-0000:00:1d.1-2/input0
[ 13.046519] usbcore: registered new interface driver usbhid
[ 13.046533] usbhid: v2.6:USB HID core driver
[ 13.066077] usbcore: registered new interface driver snd-usb-audio
[ 13.225589] phy0: Selected rate control algorithm 'pid'
[ 13.255979] Registered led device: rt73usb-phy0:radio
[ 13.255990] Registered led device: rt73usb-phy0:assoc
[ 13.256008] Registered led device: rt73usb-phy0:quality
[ 13.256456] usbcore: registered new interface driver rt73usb
[ 13.343510] lp: driver loaded but no devices found
[ 13.364612] ieee1394: raw1394: /dev/raw1394 device initialized
[ 13.374082] video1394: Installed video1394 module
[ 13.437295] Adding 1028152k swap on /dev/sdc2. Priority:-1 extents:1 across:1028152k
[ 17.008011] type=1505 audit(1256151683.078:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2395
[ 17.043516] type=1505 audit(1256151683.110:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2399
[ 17.043570] type=1505 audit(1256151683.110:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2399
[ 17.043595] type=1505 audit(1256151683.110:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2399
[ 17.043619] type=1505 audit(1256151683.110:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2399
[ 17.123731] type=1505 audit(1256151683.190:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2404
[ 17.123825] type=1505 audit(1256151683.190:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2404
[ 17.140951] type=1505 audit(1256151683.210:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2408
[ 17.880588] usb-storage: device scan complete
[ 17.881215] scsi 6:0:0:0: Direct-Access Corsair Flash Voyager 0.00 PQ: 0 ANSI: 2
[ 17.882831] sd 6:0:0:0: [sde] 63176704 512-byte hardware sectors: (32.3 GB/30.1 GiB)
[ 17.883171] usb-storage: device scan complete
[ 17.883458] sd 6:0:0:0: [sde] Write Protect is off
[ 17.883459] sd 6:0:0:0: [sde] Mode Sense: 00 00 00 00
[ 17.883461] sd 6:0:0:0: [sde] Assuming drive cache: write through
[ 17.886075] sd 6:0:0:0: [sde] 63176704 512-byte hardware sectors: (32.3 GB/30.1 GiB)
[ 17.887725] sd 6:0:0:0: [sde] Write Protect is off
[ 17.887727] sd 6:0:0:0: [sde] Mode Sense: 00 00 00 00
[ 17.887728] sd 6:0:0:0: [sde] Assuming drive cache: write through
[ 17.887730] sde:<5>scsi 7:0:0:0: Direct-Access HP photosmart 7700 1.00 PQ: 0 ANSI: 2
[ 18.020974] sde1
[ 18.021058] sd 6:0:0:0: [sde] Attached SCSI removable disk
[ 18.021107] sd 6:0:0:0: Attached scsi generic sg5 type 0
[ 18.046482] sd 7:0:0:0: [sdf] Attached SCSI removable disk
[ 18.046532] sd 7:0:0:0: Attached scsi generic sg6 type 0
[ 22.483643] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 22.483645] Bluetooth: BNEP filters: protocol multicast
[ 22.563726] Bridge firewalling registered
[ 24.943974] ppdev: user-space parallel port driver
[ 27.930927] r8169: eth0: link down
[ 27.931050] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 27.931455] rt73usb 1-1:1.0: firmware: requesting rt73.bin
[ 28.161986] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 31.178101] wlan0: authenticate with AP 00:11:6b:61:0c:e6
[ 31.179606] wlan0: authenticated
[ 31.179608] wlan0: associate with AP 00:11:6b:61:0c:e6
[ 31.182105] wlan0: RX AssocResp from 00:11:6b:61:0c:e6 (capab=0x431 status=43 aid=0)
[ 31.182107] wlan0: AP denied association (code=43)
[ 31.376008] wlan0: associate with AP 00:11:6b:61:0c:e6
[ 31.378236] wlan0: RX AssocResp from 00:11:6b:61:0c:e6 (capab=0x431 status=0 aid=1)
[ 31.378238] wlan0: associated
[ 31.380404] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 33.240322] padlock: VIA PadLock not detected.
[ 42.028004] wlan0: no IPv6 routers present

[xdgr2001]

Δώσε περισσότερες πληροφορίες για την κάρτα ήχου σύμφωνα με τις οδηγίες στο
viewtopic.php?f=9&t=7242&p=75862

http://www.alsa-project.org/db/?f=c25cb ... cc4ea2f004

[logari81]

γενικά υπάρχουν διάφορα περίεργα μηνύματα σφάλματος όπως αυτο:

[ 13.030006] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22

που δεν θα επρεπε να υπάρχουν. Επειδή όμως βλέπω ότι εκτος απο την κάρτα τηλεόρασης εχεις και μια ακομα κάρτα ήχου

04:00.0 Audio device: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG

θα σου συνιστουσα να αποσυνδεσεις ότι δεν χρειάζεσαι. Μία υποψία ειναι οτι ίσως να μην υπάρχει αρκετει τροφοδοσία για όλες τις pci συσκευές που έχεις συνδεμένες. Ή ότι γενικά κάτι παει στραβα στην motherboard. Πιστευω ότι αν αφήσεις μονο την καρτα ηχου που χρησιμοποιείς ότι θα λυθει το προβλημα. Καντο για δοκιμή και βλέπουμε.

[simosx]

Δώσε περισσότερες πληροφορίες για την κάρτα ήχου σύμφωνα με τις οδηγίες στο
viewtopic.php?f=9&t=7242&p=75862

http://www.alsa-project.org/db/?f=c25cb ... cc4ea2f004

Έχεις μπόλικες κάρτες για είσοδο/έξοδο ήχου: ενσωματωμένη κάρτα ήχου (προεπιλογή), εξωτερική κάρτα X-Fi (σε 9.10 δουλεύει δίχως πρόβλημα, όπως είπε μέλος μας νωρίτερα σήμερα), TV Tuner και USB μικρόφωνο.

Αυτό που δε βλέπουμε είναι κάποια μηνύματα όταν ο ήχος κολλάει. Εδώ φαίνεται ότι εμφάνισες τα μηνύματα συστήματος πριν συμβεί το πρόβλημα. Δοκίμασε να το κάνεις ξανά όταν συμβεί το πρόβλημα μερικές φορές.

Το chipset σου είναι το ALC888. Είναι πιθανό σε 9.10 να έχει ανανεωθεί το υποσύστημα Alsa (ήχος) και το πρόβλημα να έχει ουσιαστικά επιλυθεί. Αν έχεις καλή σύνδεση με το διαδίκτυο, τότε μπορείς απλά να δοκιμάσεις κάτι τέτοιο.

Αν δεν μπορείς να αναβαθμίσεις σύντομα, υπάρχει η δυνατότητα να βάλεις ο ίδιος την πιο πρόσφατη έκδοση της Alsa. Δες τον οδηγό στο φόρουμ. Γενικά η συμπεριφορά που αντιμετωπίζεις πρόκειται για σφάλμα στην Alsa.

[xdgr2001]

Ευχαριστω θα περιμένω την επισημη διανομή της έκδοσης 9.10 για να κάνω αναβάθμιση και θα σας ενημερωσω για τα αποτελέσματα

ευχαριστω πολύ

[xdgr2001]

Τελικά έκανα την αναβαθμιση του alsa συμφωνα με της οδηγίες και όλα είναι εντάξει.

Ευχαριστώ πολύ

Χρήστος