Wireless N USB Adapter

[avounotr]

Καλησπέρα,
έχω αγοράσει ένα Wireless TL-WN821N adapter για να πιάνω δίκτυα. Το πρόβλημα που αντιμετωπίζω είναι ότι θέλω να το κάνω να λειτουργήσει σε περιβάλλον linux αλλά δεν λειτουργεί. Μάλλον πρέπει από όσο κατάλαβα να κάνω εγκατάσταση τα drivers αλλά δεν ξέρω πώς. Το πρόβλημα είναι ότι στον υπολογιστή που πρέπει να το κάνω αυτό δεν υπάρχει σύνδεση Internet, οπότε πρέπει να μεταφέρω κάποια αρχεία από άλλο pc που έχει Internet. Αν κάποιος μπορεί να βοηθήσει όμως να μου πει και το πιο χαζό βήμα γιατί είμαι λίγο ασχετούλης....
Ευχαριστώ πολύ.

[logari81]

καταρχην να συνδεσεις το stick, να τρεξεις την εντολη

Κώδικας: Επιλογή όλων

lsusb

να αντιγράψεις κάπου το αποτελεσμα και να μας το ποσταρει εδώ για να δουμε το ακριβές μοντελο. Το λογικό ειναι να λειτουργει το στικ χωρις να κανεις απολύτως τιποτα.

[jim137]

δίαβασε αυτό για να πιάσεις κάποια πράγματα περί τερματικού http://forum.ubuntu-gr.org/viewtopic.php?f=9&t=367&start=0
διάβασε και αυτό http://forum.ubuntu-gr.org/viewtopic.php?f=2&t=279

[avounotr]

καταρχην να συνδεσεις το stick, να τρεξεις την εντολη

Κώδικας: Επιλογή όλων

lsusb

να αντιγράψεις κάπου το αποτελεσμα και να μας το ποσταρει εδώ για να δουμε το ακριβές μοντελο. Το λογικό ειναι να λειτουργει το στικ χωρις να κανεις απολύτως τιποτα.

Έχω το παρακάτω μήνυμα:

Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 002: ID 046d:c05b Logitech, Inc.
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 125f:1040 A-DATA Technology Co., Ltd.
Bus 001 Device 002: ID 0cf3:1002 Atheros Communications, Inc.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Όποιος μπορεί ας βοηθήσει...
Ευχαριστώ πολύ.

[logari81]

η συσκευή σου ειναι αυτήν

Bus 001 Device 002: ID 0cf3:1002 Atheros Communications, Inc.

και θα έπρεπε να λειτουργει χωρίς καμια δική σου ενέργεια με το module ar9170usb του πυρήνα του Linux που συμπεριλαμβάνεται στο Ubuntu 10.04

Δώσε μας τα αποτελέσματα των εντολών

Κώδικας: Επιλογή όλων

dmesg
lsmod
iwconfig

[avounotr]

Δίνω:
dmesg

Σε αυτή την εντολή δεν φαίνονται όλα, χάνονται τα αρχικά και μένουν τα παρακάτω...

Κώδικας: Επιλογή όλων


[ 0.369721] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.369724] pci 0000:00:1c.1: PME# disabled
[ 0.369761] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 0.369764] pci 0000:00:1c.5: PME# disabled
[ 0.369806] pci 0000:00:1d.0: reg 20 io port: [0x9880-0x989f]
[ 0.369854] pci 0000:00:1d.1: reg 20 io port: [0x9c00-0x9c1f]
[ 0.369903] pci 0000:00:1d.2: reg 20 io port: [0xa000-0xa01f]
[ 0.369954] pci 0000:00:1d.7: reg 10 32bit mmio: [0xfe8ff800-0xfe8ffbff]
[ 0.369984] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.369987] pci 0000:00:1d.7: PME# disabled
[ 0.370105] pci 0000:00:1f.2: reg 10 io port: [0xac00-0xac07]
[ 0.370109] pci 0000:00:1f.2: reg 14 io port: [0xa880-0xa883]
[ 0.370113] pci 0000:00:1f.2: reg 18 io port: [0xa800-0xa807]
[ 0.370118] pci 0000:00:1f.2: reg 1c io port: [0xa480-0xa483]
[ 0.370122] pci 0000:00:1f.2: reg 20 io port: [0xa400-0xa40f]
[ 0.370126] pci 0000:00:1f.2: reg 24 io port: [0xa080-0xa08f]
[ 0.370153] pci 0000:00:1f.3: reg 10 64bit mmio: [0xfe8ffc00-0xfe8ffcff]
[ 0.370164] pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
[ 0.370195] pci 0000:00:1f.5: reg 10 io port: [0xbc00-0xbc07]
[ 0.370199] pci 0000:00:1f.5: reg 14 io port: [0xb880-0xb883]
[ 0.370203] pci 0000:00:1f.5: reg 18 io port: [0xb800-0xb807]
[ 0.370207] pci 0000:00:1f.5: reg 1c io port: [0xb480-0xb483]
[ 0.370211] pci 0000:00:1f.5: reg 20 io port: [0xb400-0xb40f]
[ 0.370215] pci 0000:00:1f.5: reg 24 io port: [0xb080-0xb08f]
[ 0.370250] pci 0000:05:00.0: reg 10 64bit mmio: [0xe0000000-0xefffffff]
[ 0.370257] pci 0000:05:00.0: reg 18 64bit mmio: [0xfebe0000-0xfebeffff]
[ 0.370261] pci 0000:05:00.0: reg 20 io port: [0xe000-0xe0ff]
[ 0.370268] pci 0000:05:00.0: reg 30 32bit mmio: [0xfebc0000-0xfebdffff]
[ 0.370274] pci 0000:05:00.0: supports D1 D2
[ 0.370298] pci 0000:05:00.1: reg 10 64bit mmio: [0xfebfc000-0xfebfffff]
[ 0.370317] pci 0000:05:00.1: supports D1 D2
[ 0.370351] pci 0000:00:01.0: bridge io port: [0xe000-0xefff]
[ 0.370353] pci 0000:00:01.0: bridge 32bit mmio: [0xfeb00000-0xfebfffff]
[ 0.370356] pci 0000:00:01.0: bridge 64bit mmio pref: [0xe0000000-0xefffffff]
[ 0.370390] pci 0000:00:1c.0: bridge 64bit mmio pref: [0xdff00000-0xdfffffff]
[ 0.370428] pci 0000:03:00.0: reg 10 io port: [0xdc00-0xdc07]
[ 0.370435] pci 0000:03:00.0: reg 14 io port: [0xd880-0xd883]
[ 0.370442] pci 0000:03:00.0: reg 18 io port: [0xd800-0xd807]
[ 0.370448] pci 0000:03:00.0: reg 1c io port: [0xd480-0xd483]
[ 0.370455] pci 0000:03:00.0: reg 20 io port: [0xd400-0xd40f]
[ 0.370467] pci 0000:03:00.0: reg 30 32bit mmio: [0xfeaf0000-0xfeafffff]
[ 0.370478] pci 0000:03:00.0: supports D1 D2
[ 0.370479] pci 0000:03:00.0: PME# supported from D1 D2 D3hot
[ 0.370483] pci 0000:03:00.0: PME# disabled
[ 0.370521] pci 0000:00:1c.1: bridge io port: [0xd000-0xdfff]
[ 0.370524] pci 0000:00:1c.1: bridge 32bit mmio: [0xfea00000-0xfeafffff]
[ 0.370565] pci 0000:02:00.0: reg 10 io port: [0xc800-0xc8ff]
[ 0.370582] pci 0000:02:00.0: reg 18 64bit mmio: [0xdfeff000-0xdfefffff]
[ 0.370594] pci 0000:02:00.0: reg 20 64bit mmio: [0xdfef8000-0xdfefbfff]
[ 0.370600] pci 0000:02:00.0: reg 30 32bit mmio: [0xfe9e0000-0xfe9fffff]
[ 0.370610] pci 0000:02:00.0: supports D1 D2
[ 0.370611] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.370615] pci 0000:02:00.0: PME# disabled
[ 0.370657] pci 0000:00:1c.5: bridge io port: [0xc000-0xcfff]
[ 0.370660] pci 0000:00:1c.5: bridge 32bit mmio: [0xfe900000-0xfe9fffff]
[ 0.370665] pci 0000:00:1c.5: bridge 64bit mmio pref: [0xdfe00000-0xdfefffff]
[ 0.370702] pci 0000:00:1e.0: transparent bridge
[ 0.370723] bus 00 -> node 0
[ 0.370727] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.370898] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[ 0.370972] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.371080] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 0.371152] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
[ 0.371228] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[ 0.383595] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12 14 15)
[ 0.383684] ACPI: PCI Interrupt Link [LNKB] (IRQs *5)
[ 0.383770] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12 14 *15)
[ 0.383857] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 *11 12 14 15)
[ 0.383945] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled.
[ 0.384038] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 *7 10 11 12 14 15)
[ 0.384126] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 6 7 10 11 12 14 15)
[ 0.384215] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 6 7 10 11 12 *14 15)
[ 0.384300] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - A3, should be A2 [20080926]
[ 0.384327] ACPI: WMI: Mapper loaded
[ 0.384350] SCSI subsystem initialized
[ 0.384350] libata version 3.00 loaded.
[ 0.384350] usbcore: registered new interface driver usbfs
[ 0.384350] usbcore: registered new interface driver hub
[ 0.384350] usbcore: registered new device driver usb
[ 0.384350] PCI: Using ACPI for IRQ routing
[ 0.392006] Bluetooth: Core ver 2.13
[ 0.392015] NET: Registered protocol family 31
[ 0.392015] Bluetooth: HCI device and connection manager initialized
[ 0.392015] Bluetooth: HCI socket layer initialized
[ 0.392015] NET: Registered protocol family 8
[ 0.392015] NET: Registered protocol family 20
[ 0.392020] NetLabel: Initializing
[ 0.392022] NetLabel: domain hash size = 128
[ 0.392023] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.392030] NetLabel: unlabeled traffic allowed by default
[ 0.392039] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.392043] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[ 0.396035] AppArmor: AppArmor Filesystem Enabled
[ 0.404005] pnp: PnP ACPI init
[ 0.404010] ACPI: bus type pnp registered
[ 0.406615] pnp: PnP ACPI: found 16 devices
[ 0.406616] ACPI: ACPI bus type pnp unregistered
[ 0.406618] PnPBIOS: Disabled by ACPI PNP
[ 0.406624] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
[ 0.406626] system 00:01: iomem range 0xfed90000-0xfed93fff has been reserved
[ 0.406631] system 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 0.406633] system 00:07: ioport range 0x800-0x87f has been reserved
[ 0.406637] system 00:07: ioport range 0x500-0x57f has been reserved
[ 0.406638] system 00:07: ioport range 0x900-0x90f has been reserved
[ 0.406640] system 00:07: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.406642] system 00:07: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.406644] system 00:07: iomem range 0xfed40000-0xfed8ffff has been reserved
[ 0.406648] system 00:0a: iomem range 0xffc00000-0xffefffff has been reserved
[ 0.406651] system 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
[ 0.406653] system 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.406656] system 00:0d: ioport range 0x280-0x28f has been reserved
[ 0.406658] system 00:0d: ioport range 0x290-0x29f has been reserved
[ 0.406661] system 00:0e: iomem range 0xf8000000-0xfbffffff has been reserved
[ 0.406665] system 00:0f: iomem range 0x0-0x9ffff could not be reserved
[ 0.406667] system 00:0f: iomem range 0xc0000-0xcffff could not be reserved
[ 0.406668] system 00:0f: iomem range 0xe0000-0xfffff could not be reserved
[ 0.406670] system 00:0f: iomem range 0x100000-0x7fffffff could not be reserved
[ 0.406672] system 00:0f: iomem range 0xfed90000-0xffffffff could not be reserved
[ 0.441291] pci 0000:00:01.0: PCI bridge, secondary bus 0000:05
[ 0.441293] pci 0000:00:01.0: IO window: 0xe000-0xefff
[ 0.441296] pci 0000:00:01.0: MEM window: 0xfeb00000-0xfebfffff
[ 0.441298] pci 0000:00:01.0: PREFETCH window: 0x000000e0000000-0x000000efffffff
[ 0.441301] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:04
[ 0.441302] pci 0000:00:1c.0: IO window: disabled
[ 0.441306] pci 0000:00:1c.0: MEM window: disabled
[ 0.441308] pci 0000:00:1c.0: PREFETCH window: 0x000000dff00000-0x000000dfffffff
[ 0.441313] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
[ 0.441315] pci 0000:00:1c.1: IO window: 0xd000-0xdfff
[ 0.441318] pci 0000:00:1c.1: MEM window: 0xfea00000-0xfeafffff
[ 0.441321] pci 0000:00:1c.1: PREFETCH window: disabled
[ 0.441325] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:02
[ 0.441327] pci 0000:00:1c.5: IO window: 0xc000-0xcfff
[ 0.441330] pci 0000:00:1c.5: MEM window: 0xfe900000-0xfe9fffff
[ 0.441333] pci 0000:00:1c.5: PREFETCH window: 0x000000dfe00000-0x000000dfefffff
[ 0.441338] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
[ 0.441339] pci 0000:00:1e.0: IO window: disabled
[ 0.441342] pci 0000:00:1e.0: MEM window: disabled
[ 0.441345] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.441353] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.441355] pci 0000:00:01.0: setting latency timer to 64
[ 0.441360] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.441363] pci 0000:00:1c.0: setting latency timer to 64
[ 0.441368] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.441371] pci 0000:00:1c.1: setting latency timer to 64
[ 0.441376] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.441378] pci 0000:00:1c.5: setting latency timer to 64
[ 0.441383] pci 0000:00:1e.0: setting latency timer to 64
[ 0.441385] bus: 00 index 0 io port: [0x00-0xffff]
[ 0.441387] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[ 0.441388] bus: 05 index 0 io port: [0xe000-0xefff]
[ 0.441389] bus: 05 index 1 mmio: [0xfeb00000-0xfebfffff]
[ 0.441391] bus: 05 index 2 mmio: [0xe0000000-0xefffffff]
[ 0.441392] bus: 05 index 3 mmio: [0x0-0x0]
[ 0.441393] bus: 04 index 0 mmio: [0x0-0x0]
[ 0.441394] bus: 04 index 1 mmio: [0x0-0x0]
[ 0.441396] bus: 04 index 2 mmio: [0xdff00000-0xdfffffff]
[ 0.441397] bus: 04 index 3 mmio: [0x0-0x0]
[ 0.441398] bus: 03 index 0 io port: [0xd000-0xdfff]
[ 0.441399] bus: 03 index 1 mmio: [0xfea00000-0xfeafffff]
[ 0.441400] bus: 03 index 2 mmio: [0x0-0x0]
[ 0.441401] bus: 03 index 3 mmio: [0x0-0x0]
[ 0.441403] bus: 02 index 0 io port: [0xc000-0xcfff]
[ 0.441404] bus: 02 index 1 mmio: [0xfe900000-0xfe9fffff]
[ 0.441405] bus: 02 index 2 mmio: [0xdfe00000-0xdfefffff]
[ 0.441406] bus: 02 index 3 mmio: [0x0-0x0]
[ 0.441408] bus: 01 index 0 mmio: [0x0-0x0]
[ 0.441409] bus: 01 index 1 mmio: [0x0-0x0]
[ 0.441410] bus: 01 index 2 mmio: [0x0-0x0]
[ 0.441411] bus: 01 index 3 io port: [0x00-0xffff]
[ 0.441412] bus: 01 index 4 mmio: [0x000000-0xffffffff]
[ 0.441417] NET: Registered protocol family 2
[ 0.456032] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.456172] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.456361] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.456458] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.456460] TCP reno registered
[ 0.460046] NET: Registered protocol family 1
[ 0.460116] checking if image is initramfs...<7>Switched to high resolution mode on CPU 1
[ 0.504003] Switched to high resolution mode on CPU 0
[ 0.653759] it is
[ 0.861960] Freeing initrd memory: 7369k freed
[ 0.862092] cpufreq: No nForce2 chipset.
[ 0.862182] audit: initializing netlink socket (disabled)
[ 0.862195] type=2000 audit(1276626146.860:1): initialized
[ 0.867000] highmem bounce pool size: 64 pages
[ 0.867004] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.867825] VFS: Disk quotas dquot_6.5.1
[ 0.867861] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.868237] fuse init (API version 7.10)
[ 0.868289] msgmni has been set to 1698
[ 0.868397] alg: No test for stdrng (krng)
[ 0.868403] io scheduler noop registered
[ 0.868404] io scheduler anticipatory registered
[ 0.868406] io scheduler deadline registered
[ 0.868414] io scheduler cfq registered (default)
[ 0.868522] pci 0000:05:00.0: Boot video device
[ 0.871182] pcieport-driver 0000:00:01.0: setting latency timer to 64
[ 0.871203] pcieport-driver 0000:00:01.0: found MSI capability
[ 0.871218] pcieport-driver 0000:00:01.0: irq 2303 for MSI/MSI-X
[ 0.871224] pci_express 0000:00:01.0:pcie00: allocate port service
[ 0.871232] pci_express 0000:00:01.0:pcie03: allocate port service
[ 0.871262] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 0.871287] pcieport-driver 0000:00:1c.0: found MSI capability
[ 0.871304] pcieport-driver 0000:00:1c.0: irq 2302 for MSI/MSI-X
[ 0.871312] pci_express 0000:00:1c.0:pcie00: allocate port service
[ 0.871320] pci_express 0000:00:1c.0:pcie02: allocate port service
[ 0.871329] pci_express 0000:00:1c.0:pcie03: allocate port service
[ 0.871369] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[ 0.871393] pcieport-driver 0000:00:1c.1: found MSI capability
[ 0.871410] pcieport-driver 0000:00:1c.1: irq 2301 for MSI/MSI-X
[ 0.871418] pci_express 0000:00:1c.1:pcie00: allocate port service
[ 0.871426] pci_express 0000:00:1c.1:pcie02: allocate port service
[ 0.871435] pci_express 0000:00:1c.1:pcie03: allocate port service
[ 0.871474] pcieport-driver 0000:00:1c.5: setting latency timer to 64
[ 0.871498] pcieport-driver 0000:00:1c.5: found MSI capability
[ 0.871515] pcieport-driver 0000:00:1c.5: irq 2300 for MSI/MSI-X
[ 0.871523] pci_express 0000:00:1c.5:pcie00: allocate port service
[ 0.871531] pci_express 0000:00:1c.5:pcie02: allocate port service
[ 0.871538] pci_express 0000:00:1c.5:pcie03: allocate port service
[ 0.871584] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.872181] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.872273] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 0.872274] ACPI: Power Button (FF) [PWRF]
[ 0.872308] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 0.872310] ACPI: Power Button (CM) [PWRB]
[ 0.872483] processor ACPI_CPU:00: registered as cooling_device0
[ 0.872510] processor ACPI_CPU:01: registered as cooling_device1
[ 0.874891] isapnp: Scanning for PnP cards...
[ 1.228385] isapnp: No Plug & Play device found
[ 1.236622] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 1.236699] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.237022] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.237484] brd: module loaded
[ 1.237675] loop: module loaded
[ 1.237716] Fixed MDIO Bus: probed
[ 1.237719] PPP generic driver version 2.4.2
[ 1.237752] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 1.237769] Driver 'sd' needs updating - please use bus_type methods
[ 1.237774] Driver 'sr' needs updating - please use bus_type methods
[ 1.237821] ata_piix 0000:00:1f.2: version 2.12
[ 1.237831] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.237833] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 1.237862] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 1.237896] scsi0 : ata_piix
[ 1.237943] scsi1 : ata_piix
[ 1.238827] ata1: SATA max UDMA/133 cmd 0xac00 ctl 0xa880 bmdma 0xa400 irq 19
[ 1.238831] ata2: SATA max UDMA/133 cmd 0xa800 ctl 0xa480 bmdma 0xa408 irq 19
[ 2.032048] ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.032057] ata1.01: SATA link down (SStatus 0 SControl 300)
[ 2.040333] ata1.00: ATA-8: Hitachi HDS721032CLA362, JPFOA39C, max UDMA/133
[ 2.040335] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 2.056349] ata1.00: configured for UDMA/133
[ 2.852046] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.852055] ata2.01: SATA link down (SStatus 0 SControl 300)
[ 2.860169] ata2.00: ATAPI: Optiarc DVD RW AD-7240S, 1.03, max UDMA/100
[ 2.876183] ata2.00: configured for UDMA/100
[ 2.876736] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS72103 JPFO PQ: 0 ANSI: 5
[ 2.876796] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 2.876806] sd 0:0:0:0: [sda] Write Protect is off
[ 2.876808] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.876823] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.876861] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 2.876870] sd 0:0:0:0: [sda] Write Protect is off
[ 2.876871] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.876886] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.876888] sda: sda1 sda2 < sda5 sda6 > sda3
[ 2.919521] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.919546] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.920805] scsi 1:0:0:0: CD-ROM Optiarc DVD RW AD-7240S 1.03 PQ: 0 ANSI: 5
[ 2.925301] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.925303] Uniform CD-ROM driver Revision: 3.20
[ 2.925354] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.925380] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 2.925392] ata_piix 0000:00:1f.5: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.925394] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[ 2.925418] ata_piix 0000:00:1f.5: setting latency timer to 64
[ 2.925443] scsi2 : ata_piix
[ 2.925478] scsi3 : ata_piix
[ 2.926213] ata3: SATA max UDMA/133 cmd 0xbc00 ctl 0xb880 bmdma 0xb400 irq 19
[ 2.926216] ata4: SATA max UDMA/133 cmd 0xb800 ctl 0xb480 bmdma 0xb408 irq 19
[ 3.254506] ata3: SATA link down (SStatus 0 SControl 300)
[ 3.582496] ata4: SATA link down (SStatus 0 SControl 300)
[ 3.582826] pata_via 0000:03:00.0: version 0.3.3
[ 3.582834] pata_via 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 3.582867] pata_via 0000:03:00.0: setting latency timer to 64
[ 3.582907] scsi4 : pata_via
[ 3.582942] scsi5 : pata_via
[ 3.583056] ata5: PATA max UDMA/133 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 irq 17
[ 3.583058] ata6: PATA max UDMA/133 cmd 0xd800 ctl 0xd480 bmdma 0xd408 irq 17
[ 3.900130] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.900142] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 3.900152] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 3.900154] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 3.900187] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 3.904075] ehci_hcd 0000:00:1a.7: debug port 1
[ 3.904079] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 3.904087] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfe8ff400
[ 3.916005] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 3.916042] usb usb1: configuration #1 chosen from 1 choice
[ 3.916059] hub 1-0:1.0: USB hub found
[ 3.916063] hub 1-0:1.0: 6 ports detected
[ 3.916129] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 3.916136] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 3.916138] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 3.916162] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 3.920067] ehci_hcd 0000:00:1d.7: debug port 1
[ 3.920071] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 3.920079] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfe8ff800
[ 3.932005] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 3.932044] usb usb2: configuration #1 chosen from 1 choice
[ 3.932059] hub 2-0:1.0: USB hub found
[ 3.932063] hub 2-0:1.0: 6 ports detected
[ 3.932121] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.932130] uhci_hcd: USB Universal Host Controller Interface driver
[ 3.932143] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.932146] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 3.932148] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 3.932177] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 3.932201] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00009400
[ 3.932247] usb usb3: configuration #1 chosen from 1 choice
[ 3.932262] hub 3-0:1.0: USB hub found
[ 3.932266] hub 3-0:1.0: 2 ports detected
[ 3.932317] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 3.932320] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 3.932322] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 3.932347] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 3.932369] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00009480
[ 3.932411] usb usb4: configuration #1 chosen from 1 choice
[ 3.932427] hub 4-0:1.0: USB hub found
[ 3.932431] hub 4-0:1.0: 2 ports detected
[ 3.932481] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 3.932485] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[ 3.932487] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 3.932515] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[ 3.932532] uhci_hcd 0000:00:1a.2: irq 19, io base 0x00009800
[ 3.932579] usb usb5: configuration #1 chosen from 1 choice
[ 3.932594] hub 5-0:1.0: USB hub found
[ 3.932598] hub 5-0:1.0: 2 ports detected
[ 3.932650] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 3.932653] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 3.932655] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 3.932680] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[ 3.932697] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00009880
[ 3.932743] usb usb6: configuration #1 chosen from 1 choice
[ 3.932757] hub 6-0:1.0: USB hub found
[ 3.932761] hub 6-0:1.0: 2 ports detected
[ 3.932812] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 3.932816] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 3.932818] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 3.932842] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[ 3.932859] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00009c00
[ 3.932902] usb usb7: configuration #1 chosen from 1 choice
[ 3.932917] hub 7-0:1.0: USB hub found
[ 3.932921] hub 7-0:1.0: 2 ports detected
[ 3.932973] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 3.932976] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 3.932978] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.933002] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[ 3.933020] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a000
[ 3.933063] usb usb8: configuration #1 chosen from 1 choice
[ 3.933078] hub 8-0:1.0: USB hub found
[ 3.933081] hub 8-0:1.0: 2 ports detected
[ 3.933158] usbcore: registered new interface driver libusual
[ 3.933178] usbcore: registered new interface driver usbserial
[ 3.933185] USB Serial support registered for generic
[ 3.933195] usbcore: registered new interface driver usbserial_generic
[ 3.933196] usbserial: USB Serial Driver core
[ 3.933227] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 3.933228] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 3.933699] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.936522] mice: PS/2 mouse device common for all mice
[ 3.948540] rtc_cmos 00:03: RTC can wake from S4
[ 3.948560] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 3.948580] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 3.948617] device-mapper: uevent: version 1.0.3
[ 3.948665] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 3.948706] device-mapper: multipath: version 1.0.5 loaded
[ 3.948708] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 3.948752] EISA: Probing bus 0 at eisa.0
[ 3.948773] EISA: Detected 0 cards.
[ 3.948800] cpuidle: using governor ladder
[ 3.948801] cpuidle: using governor menu
[ 3.949110] TCP cubic registered
[ 3.949172] NET: Registered protocol family 10
[ 3.949437] lo: Disabled Privacy Extensions
[ 3.949646] NET: Registered protocol family 17
[ 3.949656] Bluetooth: L2CAP ver 2.11
[ 3.949657] Bluetooth: L2CAP socket layer initialized
[ 3.949659] Bluetooth: SCO (Voice Link) ver 0.6
[ 3.949660] Bluetooth: SCO socket layer initialized
[ 3.949675] Bluetooth: RFCOMM socket layer initialized
[ 3.949678] Bluetooth: RFCOMM TTY layer initialized
[ 3.949679] Bluetooth: RFCOMM ver 1.10
[ 3.949711] Using IPI No-Shortcut mode
[ 3.949751] registered taskstats version 1
[ 3.949832] Magic number: 14:857:392
[ 3.949871] rtc_cmos 00:03: setting system clock to 2010-06-15 18:22:30 UTC (1276626150)
[ 3.949873] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 3.949874] EDD information not available.
[ 3.950013] Freeing unused kernel memory: 532k freed
[ 3.950087] Write protecting the kernel text: 4128k
[ 3.950114] Write protecting the kernel read-only data: 1532k
[ 3.982517] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 4.077039] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 4.077053] r8169 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 4.077068] r8169 0000:02:00.0: setting latency timer to 64
[ 4.077149] r8169 0000:02:00.0: irq 2299 for MSI/MSI-X
[ 4.077552] eth0: RTL8168d/8111d at 0xf7c90000, 00:19:66:f7:a7:77, XID 281000c0 IRQ 2299
[ 4.228515] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 4.415939] usb 1-1: configuration #1 chosen from 1 choice
[ 4.663558] PM: Starting manual resume from disk
[ 4.663560] PM: Resume from partition 8:1
[ 4.663561] PM: Checking hibernation image.
[ 4.663698] PM: Resume from disk failed.
[ 4.693583] EXT4-fs: barriers enabled
[ 4.715623] kjournald2 starting. Commit interval 5 seconds
[ 4.715632] EXT4-fs: delayed allocation enabled
[ 4.715633] EXT4-fs: file extents enabled
[ 4.723200] EXT4-fs: mballoc enabled
[ 4.723203] EXT4-fs: mounted filesystem with ordered data mode.
[ 4.856508] usb 8-1: new low speed USB device using uhci_hcd and address 2
[ 5.032101] usb 8-1: configuration #1 chosen from 1 choice
[ 7.741944] udev: starting version 141
[ 7.841565] Linux agpgart interface v0.103
[ 8.434698] usbcore: registered new interface driver hiddev
[ 8.449232] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb8/8-1/8-1:1.0/input/input4
[ 8.460076] generic-usb 0003:046D:C05B.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.2-1/input0
[ 8.460089] usbcore: registered new interface driver usbhid
[ 8.460103] usbhid: v2.6:USB HID core driver
[ 8.474422] iTCO_vendor_support: vendor-support=0
[ 8.475333] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 8.475500] iTCO_wdt: Found a ICH10 TCO device (Version=2, TCOBASE=0x0860)
[ 8.475564] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 8.491043] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 8.561197] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 8.561254] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 8.625258] HDA Intel 0000:05:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 8.625279] HDA Intel 0000:05:00.1: setting latency timer to 64
[ 8.773399] lp: driver loaded but no devices found
[ 8.815763] Adding 9663088k swap on /dev/sda1. Priority:-1 extents:1 across:9663088k
[ 9.345762] EXT4 FS on sda6, internal journal on sda6:8
[ 10.526437] type=1505 audit(1276615357.074:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2015
[ 10.554488] type=1505 audit(1276615357.102:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2019
[ 10.554541] type=1505 audit(1276615357.102:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2019
[ 10.554566] type=1505 audit(1276615357.102:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2019
[ 10.554590] type=1505 audit(1276615357.102:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2019
[ 10.632499] type=1505 audit(1276615357.178:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2024
[ 10.632613] type=1505 audit(1276615357.182:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2024
[ 10.649092] type=1505 audit(1276615357.198:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2028
[ 11.590743] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 11.590745] Bluetooth: BNEP filters: protocol multicast
[ 11.603903] Bridge firewalling registered
[ 12.360440] pci 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 12.445998] [drm] Initialized drm 1.1.0 20060810
[ 12.465865] pci 0000:05:00.0: setting latency timer to 64
[ 12.465960] [drm] Initialized radeon 1.29.0 20080528 on minor 0
[ 12.543040] ppdev: user-space parallel port driver
[ 12.767456] [drm] Setting GART location based on new memory map
[ 12.782904] [drm] Loading RV730 PFP Microcode
[ 12.782926] [drm] Loading RV730 CP Microcode
[ 12.797856] [drm] Resetting GPU
[ 12.797910] [drm] writeback test succeeded in 1 usecs
[ 16.449619] r8169: eth0: link down
[ 16.449758] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 61.748007] usb 1-2: new high speed USB device using ehci_hcd and address 3
[ 61.884579] usb 1-2: configuration #1 chosen from 1 choice
[ 61.932147] Initializing USB Mass Storage driver...
[ 61.932326] scsi6 : SCSI emulation for USB Mass Storage devices
[ 61.933086] usbcore: registered new interface driver usb-storage
[ 61.933089] USB Mass Storage support registered.
[ 61.933141] usb-storage: device found at 3
[ 61.933142] usb-storage: waiting for device to settle before scanning
[ 66.932162] usb-storage: device scan complete
[ 66.933187] scsi 6:0:0:0: Direct-Access USB 2.0 USB Flash Drive 0.00 PQ: 0 ANSI: 2
[ 66.936316] sd 6:0:0:0: [sdb] 3948544 512-byte hardware sectors: (2.02 GB/1.88 GiB)
[ 66.940694] sd 6:0:0:0: [sdb] Write Protect is off
[ 66.940697] sd 6:0:0:0: [sdb] Mode Sense: 00 00 00 00
[ 66.940698] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 66.943768] sd 6:0:0:0: [sdb] 3948544 512-byte hardware sectors: (2.02 GB/1.88 GiB)
[ 66.944892] sd 6:0:0:0: [sdb] Write Protect is off
[ 66.944893] sd 6:0:0:0: [sdb] Mode Sense: 00 00 00 00
[ 66.944895] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 66.944898] sdb: sdb1
[ 67.047215] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 67.047259] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 151.177952] usb 1-2: USB disconnect, address 3
[ 849.156007] usb 1-2: new high speed USB device using ehci_hcd and address 4
[ 849.292511] usb 1-2: configuration #1 chosen from 1 choice
[ 849.292677] scsi7 : SCSI emulation for USB Mass Storage devices
[ 849.292805] usb-storage: device found at 4
[ 849.292806] usb-storage: waiting for device to settle before scanning
[ 854.292176] usb-storage: device scan complete
[ 854.293169] scsi 7:0:0:0: Direct-Access USB 2.0 USB Flash Drive 0.00 PQ: 0 ANSI: 2
[ 854.296581] sd 7:0:0:0: [sdb] 3948544 512-byte hardware sectors: (2.02 GB/1.88 GiB)
[ 854.298203] sd 7:0:0:0: [sdb] Write Protect is off
[ 854.298205] sd 7:0:0:0: [sdb] Mode Sense: 00 00 00 00
[ 854.298206] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 854.301157] sd 7:0:0:0: [sdb] 3948544 512-byte hardware sectors: (2.02 GB/1.88 GiB)
[ 854.302280] sd 7:0:0:0: [sdb] Write Protect is off
[ 854.302281] sd 7:0:0:0: [sdb] Mode Sense: 00 00 00 00
[ 854.302283] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 854.302285] sdb: sdb1
[ 854.404611] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[ 854.404657] sd 7:0:0:0: Attached scsi generic sg2 type 0
[ 1070.451264] usb 1-2: USB disconnect, address 4




Δίνω:
lsmod

Αποτέλεσμα:

Κώδικας: Επιλογή όλων


Module Size Used by
nls_iso8859_1 12032 0
nls_cp437 13696 0
vfat 18816 0
fat 58272 1 vfat
usb_storage 82880 0
binfmt_misc 16776 1
ppdev 15620 0
radeon 342816 2
drm 96296 3 radeon
bridge 56340 0
stp 10500 1 bridge
bnep 20224 2
input_polldev 11912 0
video 25360 0
output 11008 1 video
lp 17156 0
parport 42220 2 ppdev,lp
snd_seq_dummy 10756 0
snd_seq_oss 37760 0
snd_hda_intel 435636 3
snd_seq_midi 14336 0
snd_rawmidi 29696 1 snd_seq_midi
snd_pcm_oss 46336 0
snd_mixer_oss 22656 1 snd_pcm_oss
snd_seq_midi_event 15104 2 snd_seq_oss,snd_seq_midi
snd_pcm 82948 2 snd_hda_intel,snd_pcm_oss
pcspkr 10496 0
iTCO_wdt 19108 0
iTCO_vendor_support 11652 1 iTCO_wdt
snd_seq 56880 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 29704 2 snd_pcm,snd_seq
snd_seq_device 14988 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
usbhid 42336 0
intel_agp 34108 0
agpgart 42696 2 drm,intel_agp
snd 62628 15 snd_seq_oss,snd_hda_intel,snd_rawmidi,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq,snd_timer,snd_seq_device
soundcore 15200 1 snd
snd_page_alloc 16904 2 snd_hda_intel,snd_pcm
r8169 40836 0
mii 13312 1 r8169
fbcon 46112 0
tileblit 10752 1 fbcon
font 16384 1 fbcon
bitblit 13824 1 fbcon
softcursor 9984 1 bitblit



Δίνω:
iwconfig

Αποτέλεσμα:

Κώδικας: Επιλογή όλων



lo no wireless extensions.

eth0 no wireless extensions.

pan0 no wireless extensions.



[xaris2335]

1. Φτιάξε την υπογραφή σου, δες πως είναι η δική μου τον δυσκολεύει πολύ τον άλλον έτσι
2. Βάλτα τα αποτελέσματα
   

   Κώδικας: Επιλογή όλων

   εδώ μέσα

[xaris2335]

Για δοκίμασε να δώσεις και πες αν έγινε κάτι

Κώδικας: Επιλογή όλων

sudo modprobe ar9170usb

[avounotr]

Έφτιαξα την υπογραφή μου..
Αυτό εννοούσες;
Τώρα πάω να το πληκτρολογήσω

[avounotr]

Τώρα κατάλαβα τι εννοούσες πριν,
είδα την εντολή που λέει code.
Γενικά έβαλα τα στοιχεία μου αλλά δεν βλέπω να εμφανίζεται κάτι...

Έδωσα την εντολή και πήρα αυτό το αποτέλεσμα:

Κώδικας: Επιλογή όλων


FATAL: Module ar9170usb not found.