Χρειάζομαι βοήθεια γθα εγκατάσταση usb wifi Realtek RTL8188

[Vatos]

Πρόσφατα προμηθεύτηκα ένα usb Wifi της Realtek και δεν έχω καταφέρει να το κάνω να λειτουργήσει στο Laptop μου.
Το Laptop διαθέτει ασύρματη κάρτα βέβαια, αλλά εγώ θέλω να λειτουργήσω το usb που αγόρασα αλλά δεν το έχω καταφέρει έως τώρα. Έχω ακολουθήσει χιλιάδες οδηγίες που αναζήτησα στο google, όμως τίποτα.

Να αναφέρω οτι η εταιρία παρέχει drivers για linux μέσα στο cd.

Παραθέτω τα στοιχεία που χρειάζονται:

iwcofig:
eth0 no wireless extensions.

wlan0 IEEE 802.11abg ESSID:"Nekras"
Mode:Managed Frequency:2.412 GHz Access Point: 00:90:D0:F0:54:82
Bit Rate=54 Mb/s Tx-Power=15 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=70/70 Signal level=-33 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

wlan1 802.11b/g Mode:Managed Access Point: Not-Associated
Bit Rate:0 kb/s
Retry min limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

pan0 no wireless extensions.


dmesg:

[ 0.008000] CPU: Physical Processor ID: 0
[ 0.008000] CPU: Processor Core ID: 1
[ 0.008000] CPU1: Thermal monitoring handled by SMI
[ 0.180112] CPU1: Genuine Intel(R) CPU T2250 @ 1.73GHz stepping 08
[ 0.180129] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.184022] Brought up 2 CPUs
[ 0.184025] Total of 2 processors activated (6924.49 BogoMIPS).
[ 0.184549] CPU0 attaching sched-domain:
[ 0.184553] domain 0: span 0-1 level MC
[ 0.184556] groups: 0 1
[ 0.184564] CPU1 attaching sched-domain:
[ 0.184567] domain 0: span 0-1 level MC
[ 0.184570] groups: 1 0
[ 0.184694] devtmpfs: initialized
[ 0.184694] regulator: core version 0.5
[ 0.184694] Time: 23:20:38 Date: 10/18/10
[ 0.184694] NET: Registered protocol family 16
[ 0.184694] Trying to unpack rootfs image as initramfs...
[ 0.184694] EISA bus registered
[ 0.184694] ACPI: bus type pci registered
[ 0.184694] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.184694] PCI: Not using MMCONFIG.
[ 0.184694] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=6
[ 0.184694] PCI: Using configuration type 1 for base access
[ 0.188129] bio: create slab <bio-0> at 0
[ 0.189626] ACPI: EC: Look up EC in DSDT
[ 0.192362] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.206588] ACPI: Interpreter enabled
[ 0.206597] ACPI: (supports S0 S3 S4 S5)
[ 0.206631] ACPI: Using IOAPIC for interrupt routing
[ 0.206705] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.215782] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
[ 0.215788] PCI: updated MCFG configuration 0: base e0000000 segment 0 buses 0 - 63
[ 0.215791] PCI: Using MMCONFIG for extended config space
[ 0.225201] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[ 0.225545] ACPI: No dock devices found.
[ 0.225708] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.225850] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.225855] pci 0000:00:01.0: PME# disabled
[ 0.225956] pci 0000:00:1b.0: reg 10 64bit mmio: [0xfebfc000-0xfebfffff]
[ 0.226024] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.226030] pci 0000:00:1b.0: PME# disabled
[ 0.226135] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.226141] pci 0000:00:1c.0: PME# disabled
[ 0.226248] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.226254] pci 0000:00:1c.1: PME# disabled
[ 0.226360] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.226366] pci 0000:00:1c.2: PME# disabled
[ 0.226441] pci 0000:00:1d.0: reg 20 io port: [0xec00-0xec1f]
[ 0.226514] pci 0000:00:1d.1: reg 20 io port: [0xe880-0xe89f]
[ 0.226586] pci 0000:00:1d.2: reg 20 io port: [0xe800-0xe81f]
[ 0.226658] pci 0000:00:1d.3: reg 20 io port: [0xe480-0xe49f]
[ 0.226735] pci 0000:00:1d.7: reg 10 32bit mmio: [0xfebfbc00-0xfebfbfff]
[ 0.226804] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.226810] pci 0000:00:1d.7: PME# disabled
[ 0.227003] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[ 0.227008] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[ 0.227018] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0250 (mask 000f)
[ 0.227096] pci 0000:00:1f.2: reg 10 io port: [0x00-0x07]
[ 0.227105] pci 0000:00:1f.2: reg 14 io port: [0x00-0x03]
[ 0.227114] pci 0000:00:1f.2: reg 18 io port: [0x00-0x07]
[ 0.227124] pci 0000:00:1f.2: reg 1c io port: [0x00-0x03]
[ 0.227133] pci 0000:00:1f.2: reg 20 io port: [0xffa0-0xffaf]
[ 0.227173] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.227179] pci 0000:00:1f.2: PME# disabled
[ 0.227248] pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
[ 0.227334] pci 0000:01:00.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff]
[ 0.227349] pci 0000:01:00.0: reg 14 64bit mmio pref: [0xc0000000-0xcfffffff]
[ 0.227365] pci 0000:01:00.0: reg 1c 64bit mmio: [0xfc000000-0xfcffffff]
[ 0.227380] pci 0000:01:00.0: reg 30 32bit mmio pref: [0xfbfe0000-0xfbffffff]
[ 0.227485] pci 0000:00:01.0: bridge 32bit mmio: [0xf9f00000-0xfdffffff]
[ 0.227492] pci 0000:00:01.0: bridge 64bit mmio pref: [0xbdf00000-0xddefffff]
[ 0.227574] pci 0000:02:00.0: reg 10 io port: [0xc800-0xc8ff]
[ 0.227606] pci 0000:02:00.0: reg 18 64bit mmio: [0xfe0ff000-0xfe0fffff]
[ 0.227639] pci 0000:02:00.0: reg 30 32bit mmio pref: [0xfe0e0000-0xfe0effff]
[ 0.227707] pci 0000:02:00.0: supports D1 D2
[ 0.227710] pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold
[ 0.227718] pci 0000:02:00.0: PME# disabled
[ 0.227802] pci 0000:00:1c.0: bridge io port: [0xc000-0xcfff]
[ 0.227808] pci 0000:00:1c.0: bridge 32bit mmio: [0xfe000000-0xfe0fffff]
[ 0.228021] pci 0000:03:00.0: reg 10 32bit mmio: [0xfe1ff000-0xfe1fffff]
[ 0.228271] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 0.228285] pci 0000:03:00.0: PME# disabled
[ 0.228411] pci 0000:00:1c.1: bridge 32bit mmio: [0xfe100000-0xfe1fffff]
[ 0.228483] pci 0000:00:1c.2: bridge io port: [0xd000-0xdfff]
[ 0.228489] pci 0000:00:1c.2: bridge 32bit mmio: [0xfe200000-0xfe9fffff]
[ 0.228499] pci 0000:00:1c.2: bridge 64bit mmio pref: [0xddf00000-0xdfefffff]
[ 0.228550] pci 0000:06:01.0: reg 10 32bit mmio: [0xfeaff800-0xfeafffff]
[ 0.228616] pci 0000:06:01.0: PME# supported from D0 D3hot D3cold
[ 0.228622] pci 0000:06:01.0: PME# disabled
[ 0.228669] pci 0000:06:01.1: reg 10 32bit mmio: [0xfeaff400-0xfeaff4ff]
[ 0.228734] pci 0000:06:01.1: supports D1 D2
[ 0.228737] pci 0000:06:01.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.228743] pci 0000:06:01.1: PME# disabled
[ 0.228793] pci 0000:06:01.2: reg 10 32bit mmio: [0xfeaff000-0xfeaff0ff]
[ 0.228859] pci 0000:06:01.2: supports D1 D2
[ 0.228862] pci 0000:06:01.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.228868] pci 0000:06:01.2: PME# disabled
[ 0.228915] pci 0000:06:01.3: reg 10 32bit mmio: [0xfeafec00-0xfeafecff]
[ 0.228979] pci 0000:06:01.3: supports D1 D2
[ 0.228982] pci 0000:06:01.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.228987] pci 0000:06:01.3: PME# disabled
[ 0.229064] pci 0000:00:1e.0: transparent bridge
[ 0.229073] pci 0000:00:1e.0: bridge 32bit mmio: [0xfea00000-0xfeafffff]
[ 0.229112] pci_bus 0000:00: on NUMA node 0
[ 0.229121] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.229367] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.229451] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
[ 0.229539] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[ 0.229624] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
[ 0.229720] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 0.244153] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *11 12)
[ 0.244326] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 12)
[ 0.244486] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 12)
[ 0.244645] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 *4 5 6 7 12)
[ 0.244805] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 12) *0, disabled.
[ 0.244965] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 12) *0, disabled.
[ 0.245130] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 12) *0, disabled.
[ 0.245290] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 12)
[ 0.245458] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.245466] vgaarb: loaded
[ 0.245622] SCSI subsystem initialized
[ 0.245743] libata version 3.00 loaded.
[ 0.245833] usbcore: registered new interface driver usbfs
[ 0.245849] usbcore: registered new interface driver hub
[ 0.245884] usbcore: registered new device driver usb
[ 0.246058] ACPI: WMI: Mapper loaded
[ 0.246061] PCI: Using ACPI for IRQ routing
[ 0.246385] NetLabel: Initializing
[ 0.246388] NetLabel: domain hash size = 128
[ 0.246390] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.246406] NetLabel: unlabeled traffic allowed by default
[ 0.246448] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.246455] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.252151] Switching to clocksource tsc
[ 0.254553] AppArmor: AppArmor Filesystem Enabled
[ 0.254574] pnp: PnP ACPI init
[ 0.254594] ACPI: bus type pnp registered
[ 0.257360] pnp: PnP ACPI: found 13 devices
[ 0.257364] ACPI: ACPI bus type pnp unregistered
[ 0.257368] PnPBIOS: Disabled by ACPI PNP
[ 0.257384] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
[ 0.257397] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[ 0.257401] system 00:08: ioport range 0x800-0x87f has been reserved
[ 0.257404] system 00:08: ioport range 0x480-0x4bf has been reserved
[ 0.257408] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.257413] system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.257416] system 00:08: iomem range 0xfed45000-0xfed89fff has been reserved
[ 0.257420] system 00:08: iomem range 0xfed45000-0xfed89fff has been reserved
[ 0.257424] system 00:08: iomem range 0xffb00000-0xffbfffff could not be reserved
[ 0.257428] system 00:08: iomem range 0xfff00000-0xffffffff has been reserved
[ 0.257436] system 00:0a: ioport range 0x250-0x253 has been reserved
[ 0.257440] system 00:0a: ioport range 0x256-0x25f has been reserved
[ 0.257444] system 00:0a: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.257448] system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.257451] system 00:0a: iomem range 0xfec10000-0xfec17fff has been reserved
[ 0.257455] system 00:0a: iomem range 0xfec18000-0xfec1ffff has been reserved
[ 0.257459] system 00:0a: iomem range 0xfec20000-0xfec27fff has been reserved
[ 0.257466] system 00:0b: iomem range 0xe0000000-0xe3ffffff has been reserved
[ 0.257474] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[ 0.257477] system 00:0c: iomem range 0xc0000-0xcffff could not be reserved
[ 0.257481] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
[ 0.257485] system 00:0c: iomem range 0x100000-0x7fffffff could not be reserved
[ 0.292832] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.292837] pci 0000:00:01.0: IO window: disabled
[ 0.292842] pci 0000:00:01.0: MEM window: 0xf9f00000-0xfdffffff
[ 0.292847] pci 0000:00:01.0: PREFETCH window: 0x000000bdf00000-0x000000ddefffff
[ 0.292854] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.292858] pci 0000:00:1c.0: IO window: 0xc000-0xcfff
[ 0.292866] pci 0000:00:1c.0: MEM window: 0xfe000000-0xfe0fffff
[ 0.292872] pci 0000:00:1c.0: PREFETCH window: 0x00000080000000-0x000000801fffff
[ 0.292881] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
[ 0.292886] pci 0000:00:1c.1: IO window: 0x1000-0x1fff
[ 0.292893] pci 0000:00:1c.1: MEM window: 0xfe100000-0xfe1fffff
[ 0.292900] pci 0000:00:1c.1: PREFETCH window: 0x00000080200000-0x000000803fffff
[ 0.292909] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
[ 0.292913] pci 0000:00:1c.2: IO window: 0xd000-0xdfff
[ 0.292921] pci 0000:00:1c.2: MEM window: 0xfe200000-0xfe9fffff
[ 0.292927] pci 0000:00:1c.2: PREFETCH window: 0x000000ddf00000-0x000000dfefffff
[ 0.292937] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:06
[ 0.292940] pci 0000:00:1e.0: IO window: disabled
[ 0.292947] pci 0000:00:1e.0: MEM window: 0xfea00000-0xfeafffff
[ 0.292953] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.292980] alloc irq_desc for 16 on node -1
[ 0.292983] alloc kstat_irqs on node -1
[ 0.292993] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.292998] pci 0000:00:01.0: setting latency timer to 64
[ 0.293010] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.293016] pci 0000:00:1c.0: setting latency timer to 64
[ 0.293028] pci 0000:00:1c.1: enabling device (0106 -> 0107)
[ 0.293033] alloc irq_desc for 17 on node -1
[ 0.293035] alloc kstat_irqs on node -1
[ 0.293040] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.293046] pci 0000:00:1c.1: setting latency timer to 64
[ 0.293058] alloc irq_desc for 18 on node -1
[ 0.293060] alloc kstat_irqs on node -1
[ 0.293065] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.293071] pci 0000:00:1c.2: setting latency timer to 64
[ 0.293081] pci 0000:00:1e.0: setting latency timer to 64
[ 0.293088] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.293091] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.293095] pci_bus 0000:01: resource 1 mem: [0xf9f00000-0xfdffffff]
[ 0.293098] pci_bus 0000:01: resource 2 pref mem [0xbdf00000-0xddefffff]
[ 0.293102] pci_bus 0000:02: resource 0 io: [0xc000-0xcfff]
[ 0.293105] pci_bus 0000:02: resource 1 mem: [0xfe000000-0xfe0fffff]
[ 0.293109] pci_bus 0000:02: resource 2 pref mem [0x80000000-0x801fffff]
[ 0.293112] pci_bus 0000:03: resource 0 io: [0x1000-0x1fff]
[ 0.293116] pci_bus 0000:03: resource 1 mem: [0xfe100000-0xfe1fffff]
[ 0.293119] pci_bus 0000:03: resource 2 pref mem [0x80200000-0x803fffff]
[ 0.293122] pci_bus 0000:04: resource 0 io: [0xd000-0xdfff]
[ 0.293126] pci_bus 0000:04: resource 1 mem: [0xfe200000-0xfe9fffff]
[ 0.293129] pci_bus 0000:04: resource 2 pref mem [0xddf00000-0xdfefffff]
[ 0.293133] pci_bus 0000:06: resource 1 mem: [0xfea00000-0xfeafffff]
[ 0.293136] pci_bus 0000:06: resource 3 io: [0x00-0xffff]
[ 0.293139] pci_bus 0000:06: resource 4 mem: [0x000000-0xffffffff]
[ 0.293192] NET: Registered protocol family 2
[ 0.293318] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.293727] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.294471] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.294851] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.294855] TCP reno registered
[ 0.294974] NET: Registered protocol family 1
[ 0.295132] pci 0000:01:00.0: Boot video device
[ 0.295181] Simple Boot Flag at 0x52 set to 0x1
[ 0.295414] cpufreq-nforce2: No nForce2 chipset.
[ 0.295449] Scanning for low memory corruption every 60 seconds
[ 0.295596] audit: initializing netlink socket (disabled)
[ 0.295610] type=2000 audit(1287444037.295:1): initialized
[ 0.307758] highmem bounce pool size: 64 pages
[ 0.307768] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.309817] VFS: Disk quotas dquot_6.5.2
[ 0.309898] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.310662] fuse init (API version 7.13)
[ 0.310774] msgmni has been set to 1690
[ 0.311053] alg: No test for stdrng (krng)
[ 0.311125] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.311129] io scheduler noop registered
[ 0.311131] io scheduler anticipatory registered
[ 0.311134] io scheduler deadline registered
[ 0.311185] io scheduler cfq registered (default)
[ 0.311379] alloc irq_desc for 24 on node -1
[ 0.311382] alloc kstat_irqs on node -1
[ 0.311393] pcieport 0000:00:01.0: irq 24 for MSI/MSI-X
[ 0.311402] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.311544] alloc irq_desc for 25 on node -1
[ 0.311547] alloc kstat_irqs on node -1
[ 0.311557] pcieport 0000:00:1c.0: irq 25 for MSI/MSI-X
[ 0.311569] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.311740] alloc irq_desc for 26 on node -1
[ 0.311742] alloc kstat_irqs on node -1
[ 0.311752] pcieport 0000:00:1c.1: irq 26 for MSI/MSI-X
[ 0.311764] pcieport 0000:00:1c.1: setting latency timer to 64
[ 0.311936] alloc irq_desc for 27 on node -1
[ 0.311938] alloc kstat_irqs on node -1
[ 0.311949] pcieport 0000:00:1c.2: irq 27 for MSI/MSI-X
[ 0.311961] pcieport 0000:00:1c.2: setting latency timer to 64
[ 0.312082] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.312248] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.312436] ACPI: AC Adapter [AC0] (on-line)
[ 0.312532] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[ 0.313821] ACPI: Lid Switch [LID]
[ 0.313880] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 0.313889] ACPI: Power Button [PWRB]
[ 0.313949] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[ 0.313957] ACPI: Sleep Button [SLPB]
[ 0.314009] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 0.314013] ACPI: Power Button [PWRF]
[ 0.315032] ACPI: SSDT 7ffb91b0 00D24 (v01 AMI CPU1PM 00000001 INTL 02002026)
[ 0.315669] Marking TSC unstable due to TSC halts in idle
[ 0.315762] processor LNXCPU:00: registered as cooling_device0
[ 0.316389] ACPI Warning: Incorrect checksum in table [SSDT] - C0, should be 03 (20090903/tbutils-314)
[ 0.316396] ACPI: SSDT 7ffb9ee0 00D24 (v01 AMI CPU2PM 00000001 INTL 02002026)
[ 0.316904] Switching to clocksource hpet
[ 0.317207] processor LNXCPU:01: registered as cooling_device1
[ 0.323646] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.323657] ACPI: Thermal Zone [THRM] (55 C)
[ 0.325585] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.327347] brd: module loaded
[ 0.327950] loop: module loaded
[ 0.328059] input: Macintosh mouse button emulation as /devices/virtual/input/input4
[ 0.328181] ata_piix 0000:00:1f.2: version 2.13
[ 0.328204] alloc irq_desc for 19 on node -1
[ 0.328207] alloc kstat_irqs on node -1
[ 0.328216] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.328223] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[ 0.328281] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 0.328951] scsi0 : ata_piix
[ 0.329280] scsi1 : ata_piix
[ 0.330797] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 0.330802] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 0.331246] Fixed MDIO Bus: probed
[ 0.331290] PPP generic driver version 2.4.2
[ 0.331355] tun: Universal TUN/TAP device driver, 1.6
[ 0.331357] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.331467] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.331493] alloc irq_desc for 23 on node -1
[ 0.331496] alloc kstat_irqs on node -1
[ 0.331502] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.331523] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.331528] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.331573] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 0.331598] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 0.331612] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.335493] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 0.335580] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfebfbc00
[ 0.339514] isapnp: Scanning for PnP cards...
[ 0.349307] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.349444] usb usb1: configuration #1 chosen from 1 choice
[ 0.349481] hub 1-0:1.0: USB hub found
[ 0.349493] hub 1-0:1.0: 8 ports detected
[ 0.349589] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.349610] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.349661] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.349672] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.349676] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.349720] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.349753] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ec00
[ 0.349866] usb usb2: configuration #1 chosen from 1 choice
[ 0.349901] hub 2-0:1.0: USB hub found
[ 0.349910] hub 2-0:1.0: 2 ports detected
[ 0.349970] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.349977] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.349982] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.350022] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 0.350062] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e880
[ 0.350170] usb usb3: configuration #1 chosen from 1 choice
[ 0.350202] hub 3-0:1.0: USB hub found
[ 0.350210] hub 3-0:1.0: 2 ports detected
[ 0.350263] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.350270] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.350275] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.350311] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 0.350348] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800
[ 0.350461] usb usb4: configuration #1 chosen from 1 choice
[ 0.350493] hub 4-0:1.0: USB hub found
[ 0.350501] hub 4-0:1.0: 2 ports detected
[ 0.350554] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 0.350562] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 0.350566] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 0.350610] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 0.350646] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e480
[ 0.350754] usb usb5: configuration #1 chosen from 1 choice
[ 0.350786] hub 5-0:1.0: USB hub found
[ 0.350794] hub 5-0:1.0: 2 ports detected
[ 0.350916] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 0.353458] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 0.355660] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.356003] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.356007] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.356011] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.356014] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.356113] mice: PS/2 mouse device common for all mice
[ 0.356319] rtc_cmos 00:03: RTC can wake from S4
[ 0.356750] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.356802] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.356968] device-mapper: uevent: version 1.0.3
[ 0.359809] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.382658] ACPI: Battery Slot [BAT0] (battery present)
[ 0.397197] device-mapper: multipath: version 1.1.0 loaded
[ 0.397202] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.405163] EISA: Probing bus 0 at eisa.0
[ 0.405174] Cannot allocate resource for EISA slot 1
[ 0.405205] EISA: Detected 0 cards.
[ 0.413141] cpuidle: using governor ladder
[ 0.413257] cpuidle: using governor menu
[ 0.413835] TCP cubic registered
[ 0.414048] NET: Registered protocol family 10
[ 0.414619] lo: Disabled Privacy Extensions
[ 0.415027] NET: Registered protocol family 17
[ 0.474527] Freeing initrd memory: 7779k freed
[ 0.480838] Using IPI No-Shortcut mode
[ 0.480990] PM: Resume from disk failed.
[ 0.481049] registered taskstats version 1
[ 0.481681] Magic number: 14:90:353
[ 0.481803] rtc_cmos 00:03: setting system clock to 2010-10-18 23:20:38 UTC (1287444038)
[ 0.481807] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.481810] EDD information not available.
[ 0.488482] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 0.505926] ata2.00: ATAPI: MATSHITADVD-RAM UJ-850S, 1.21, max UDMA/33
[ 0.550783] ata1.00: ATA-8: WDC WD2500BEVS-00UST0, 01.01A01, max UDMA/133
[ 0.550788] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 0.564767] ata2.00: configured for UDMA/33
[ 0.565205] ata1.00: configured for UDMA/133
[ 0.695781] isapnp: No Plug & Play device found
[ 0.695926] scsi 0:0:0:0: Direct-Access ATA WDC WD2500BEVS-0 01.0 PQ: 0 ANSI: 5
[ 0.696089] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 0.696295] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 0.696360] sd 0:0:0:0: [sda] Write Protect is off
[ 0.696363] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.696396] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.696573] sda:
[ 0.697148] usb 1-2: new high speed USB device using ehci_hcd and address 2
[ 0.698124] scsi 1:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-850S 1.21 PQ: 0 ANSI: 5
[ 0.702869] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 0.702876] Uniform CD-ROM driver Revision: 3.20
[ 0.703087] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 0.703212] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 0.705880] sda1 sda2 < sda5 >
[ 0.733114] sd 0:0:0:0: [sda] Attached SCSI disk
[ 0.733131] Freeing unused kernel memory: 656k freed
[ 0.733630] Write protecting the kernel text: 4684k
[ 0.733691] Write protecting the kernel read-only data: 1840k
[ 0.752464] udev: starting version 151
[ 0.834875] usb 1-2: configuration #1 chosen from 1 choice
[ 0.876211] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 0.876244] r8169 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.876304] r8169 0000:02:00.0: setting latency timer to 64
[ 0.876386] alloc irq_desc for 28 on node -1
[ 0.876389] alloc kstat_irqs on node -1
[ 0.876409] r8169 0000:02:00.0: irq 28 for MSI/MSI-X
[ 0.880105] eth0: RTL8168b/8111b at 0xf804a000, 00:18:f3:3a:b4:3e, XID 18000000 IRQ 28
[ 0.914167] ohci1394 0000:06:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.948063] usb 1-8: new high speed USB device using ehci_hcd and address 3
[ 0.970066] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[feaff800-feafffff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 1.076953] usb 1-8: configuration #1 chosen from 1 choice
[ 1.139790] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 2.244534] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000368460d]
[ 18.830881] udev: starting version 151
[ 18.933614] Adding 6037496k swap on /dev/sda5. Priority:-1 extents:1 across:6037496k
[ 19.016845] lp: driver loaded but no devices found
[ 19.031209] vga16fb: initializing
[ 19.031215] vga16fb: mapped to 0xc00a0000
[ 19.031294] fb0: VGA16 VGA frame buffer device
[ 19.032281] Linux agpgart interface v0.103
[ 19.083974] intel_rng: FWH not detected
[ 19.150263] ricoh-mmc: Ricoh MMC Controller disabling driver
[ 19.150267] ricoh-mmc: Copyright(c) Philip Langdale
[ 19.150302] ricoh-mmc: Ricoh MMC controller found at 0000:06:01.2 [1180:0843] (rev 1)
[ 19.150322] ricoh-mmc: Controller is now disabled.
[ 19.152376] sdhci: Secure Digital Host Controller Interface driver
[ 19.152379] sdhci: Copyright(c) Pierre Ossman
[ 19.155101] sdhci-pci 0000:06:01.1: SDHCI controller found [1180:0822] (rev 19)
[ 19.155125] sdhci-pci 0000:06:01.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 19.158096] cfg80211: Calling CRDA to update world regulatory domain
[ 19.158172] asus_laptop: Asus Laptop Support version 0.42
[ 19.164259] asus_laptop: F3JC model detected
[ 19.170027] Registered led device: mmc0::
[ 19.171149] mmc0: SDHCI controller on PCI [0000:06:01.1] using PIO
[ 19.209234] type=1505 audit(1287444057.227:2): operation="profile_load" pid=599 name="/sbin/dhclient3"
[ 19.209946] type=1505 audit(1287444057.227:3): operation="profile_load" pid=599 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 19.210332] type=1505 audit(1287444057.227:4): operation="profile_load" pid=599 name="/usr/lib/connman/scripts/dhclient-script"
[ 19.219134] acpi device:17: registered as cooling_device2
[ 19.219564] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:13/LNXVIDEO:00/input/input6
[ 19.219705] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 19.223887] cfg80211: World regulatory domain updated:
[ 19.223891] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 19.223895] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.223898] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 19.223902] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 19.223905] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.223908] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.226659] input: Asus Laptop extra buttons as /devices/virtual/input/input7
[ 19.226802] Registered led device: asus::touchpad
[ 19.236281] asus_laptop: Brightness ignored, must be controlled by ACPI video driver
[ 19.305681] nvidia: module license 'NVIDIA' taints kernel.
[ 19.305687] Disabling lock debugging due to kernel taint
[ 19.489131] Console: switching to colour frame buffer device 80x30
[ 19.733471] type=1505 audit(1287444057.751:5): operation="profile_load" pid=726 name="/usr/share/gdm/guest-session/Xsession"
[ 19.735329] type=1505 audit(1287444057.751:6): operation="profile_replace" pid=728 name="/sbin/dhclient3"
[ 19.736141] type=1505 audit(1287444057.751:7): operation="profile_replace" pid=728 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 19.736537] type=1505 audit(1287444057.751:8): operation="profile_replace" pid=728 name="/usr/lib/connman/scripts/dhclient-script"
[ 19.741272] type=1505 audit(1287444057.759:9): operation="profile_load" pid=729 name="/usr/bin/evince"
[ 19.750616] type=1505 audit(1287444057.767:10): operation="profile_load" pid=729 name="/usr/bin/evince-previewer"
[ 19.756401] type=1505 audit(1287444057.771:11): operation="profile_load" pid=729 name="/usr/bin/evince-thumbnailer"
[ 19.888230] r8169: eth0: link down
[ 19.889050] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.234486] Synaptics Touchpad, model: 1, fw: 6.1, id: 0xa3a0b3, caps: 0xa04713/0x10008
[ 20.275860] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8
[ 20.593624] r8192s_usb: module is from the staging directory, the quality is unknown, you have been warned.
[ 20.602265] ieee80211_crypt: registered algorithm 'NULL'
[ 20.602270] ieee80211_crypt: registered algorithm 'TKIP'
[ 20.602272] ieee80211_crypt: registered algorithm 'CCMP'
[ 20.602275] ieee80211_crypt: registered algorithm 'WEP'
[ 20.602277]
[ 20.602278] Linux kernel driver for RTL8192 based WLAN cards
[ 20.602280] Copyright (c) 2007-2008, Realsil Wlan
[ 20.602446] ==>ep_num:4, in_ep_num:1, out_ep_num:3
[ 20.602449] ==>RtInPipes:3
[ 20.602452] ==>RtOutPipes:4 6 13
[ 20.602457] ==>txqueue_to_outpipemap for BK, BE, VI, VO, HCCA, TXCMD, MGNT, HIGH, BEACON:
[ 20.602459] 1 1 0 0 2 2 2 2 2
[ 20.645803] Linux video capture interface: v2.00
[ 20.672189] stkwebcam: Syntek USB2.0 Camera is now controlling video device /dev/video0
[ 20.672215] usbcore: registered new interface driver stkwebcam
[ 20.717086] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
[ 20.717092] iwl3945: Copyright(c) 2003-2009 Intel Corporation
[ 20.717223] iwl3945 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 20.717239] iwl3945 0000:03:00.0: setting latency timer to 64
[ 20.820523] iwl3945 0000:03:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels
[ 20.820529] iwl3945 0000:03:00.0: Detected Intel Wireless WiFi Link 3945ABG
[ 20.820651] alloc irq_desc for 29 on node -1
[ 20.820654] alloc kstat_irqs on node -1
[ 20.820689] iwl3945 0000:03:00.0: irq 29 for MSI/MSI-X
[ 20.849324] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 20.849340] nvidia 0000:01:00.0: setting latency timer to 64
[ 20.849347] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 20.849868] NVRM: loading NVIDIA UNIX x86 Kernel Module 195.36.24 Thu Apr 22 09:18:20 PDT 2010
[ 20.873095] phy0: Selected rate control algorithm 'iwl-3945-rs'
[ 20.934881] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 20.934918] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 21.028177] iwl3945 0000:03:00.0: firmware: requesting iwlwifi-3945-2.ucode
[ 21.056770] Dot11d_Init()
[ 21.071757] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
[ 21.089334] iwl3945 0000:03:00.0: loaded firmware version 15.32.2.9
[ 21.089561] iwl3945 0000:03:00.0: Radio disabled by HW RF Kill switch
[ 21.089885] usbcore: registered new interface driver rtl819xU
[ 21.092660] iwl3945 0000:03:00.0: Radio disabled by HW RF Kill switch
[ 32.391446] ppdev: user-space parallel port driver
[ 95.808222] usb 1-2: USB disconnect, address 2
[ 95.808428] unregister_netdevice: device wlan0/f2450000 never was registered
[ 95.808434] ------------[ cut here ]------------
[ 95.808450] WARNING: at /build/buildd/linux-2.6.32/net/core/dev.c:4650 rollback_registered+0xed/0x120()
[ 95.808457] Hardware name: F3JC
[ 95.808462] Modules linked in: binfmt_misc ppdev snd_atiixp_modem snd_via82xx_modem snd_intel8x0m snd_ac97_codec snd_hda_codec_si3054 snd_hda_codec_realtek ac97_bus snd_hda_intel snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss snd_pcm arc4 snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device iwl3945 stkwebcam joydev snd iwlcore videodev r8192s_usb(C) nvidia(P) fbcon tileblit font bitblit softcursor soundcore v4l1_compat video output mac80211 asus_laptop sdhci_pci sdhci ricoh_mmc led_class cfg80211 psmouse snd_page_alloc intel_agp serio_raw vga16fb vgastate agpgart lp parport ohci1394 ieee1394 r8169 mii
[ 95.808600] Pid: 30, comm: khubd Tainted: P C 2.6.32-25-generic #44-Ubuntu
[ 95.808607] Call Trace:
[ 95.808620] [<c014c6e2>] warn_slowpath_common+0x72/0xa0
[ 95.808630] [<c04c569d>] ? rollback_registered+0xed/0x120
[ 95.808640] [<c04c569d>] ? rollback_registered+0xed/0x120
[ 95.808652] [<c014c72a>] warn_slowpath_null+0x1a/0x20
[ 95.808661] [<c04c569d>] rollback_registered+0xed/0x120
[ 95.808671] [<c04c56ee>] unregister_netdevice+0x1e/0x70
[ 95.808681] [<c04c5757>] unregister_netdev+0x17/0x20
[ 95.808708] [<f9b861ef>] rtl8192_usb_disconnect+0x20/0xa7 [r8192s_usb]
[ 95.808719] [<c044b939>] usb_unbind_interface+0xe9/0x130
[ 95.808732] [<c03e7bd1>] __device_release_driver+0x51/0xb0
[ 95.808741] [<c03e7cf5>] device_release_driver+0x25/0x40
[ 95.808752] [<c03e6fab>] bus_remove_device+0x7b/0xa0
[ 95.808761] [<c03e5427>] device_del+0xf7/0x180
[ 95.808770] [<c04486e5>] usb_disable_device+0x85/0x100
[ 95.808780] [<c04431ae>] usb_disconnect+0x9e/0x120
[ 95.808791] [<c044370b>] hub_port_connect_change+0x8b/0x890
[ 95.808800] [<c0449325>] ? usb_control_msg+0xd5/0x130
[ 95.808810] [<c0441160>] ? clear_port_feature+0x50/0x60
[ 95.808820] [<c04446b5>] hub_events+0x1f5/0x510
[ 95.808831] [<c0167bcf>] ? finish_wait+0x4f/0x70
[ 95.808841] [<c0444a0a>] hub_thread+0x3a/0x140
[ 95.808850] [<c0167a60>] ? autoremove_wake_function+0x0/0x50
[ 95.808860] [<c04449d0>] ? hub_thread+0x0/0x140
[ 95.808868] [<c01677d4>] kthread+0x74/0x80
[ 95.808876] [<c0167760>] ? kthread+0x0/0x80
[ 95.808887] [<c0104087>] kernel_thread_helper+0x7/0x10
[ 95.808893] ---[ end trace f103cd354dfa62c8 ]---
[ 95.808900] network todo 'wlan0' but state 0
[ 95.808909] Pid: 30, comm: khubd Tainted: P WC 2.6.32-25-generic #44-Ubuntu
[ 95.808915] Call Trace:
[ 95.808923] [<c058abad>] ? printk+0x1d/0x20
[ 95.808933] [<c04c4e10>] netdev_run_todo+0x110/0x150
[ 95.808943] [<c04cf8ed>] rtnl_unlock+0xd/0x10
[ 95.808952] [<c04c575c>] unregister_netdev+0x1c/0x20
[ 95.808979] [<f9b861ef>] rtl8192_usb_disconnect+0x20/0xa7 [r8192s_usb]
[ 95.808989] [<c044b939>] usb_unbind_interface+0xe9/0x130
[ 95.809000] [<c03e7bd1>] __device_release_driver+0x51/0xb0
[ 95.809047] [<c03e7cf5>] device_release_driver+0x25/0x40
[ 95.809060] [<c03e6fab>] bus_remove_device+0x7b/0xa0
[ 95.809073] [<c03e5427>] device_del+0xf7/0x180
[ 95.809084] [<c04486e5>] usb_disable_device+0x85/0x100
[ 95.809097] [<c04431ae>] usb_disconnect+0x9e/0x120
[ 95.809110] [<c044370b>] hub_port_connect_change+0x8b/0x890
[ 95.809122] [<c0449325>] ? usb_control_msg+0xd5/0x130
[ 95.809135] [<c0441160>] ? clear_port_feature+0x50/0x60
[ 95.809148] [<c04446b5>] hub_events+0x1f5/0x510
[ 95.809161] [<c0167bcf>] ? finish_wait+0x4f/0x70
[ 95.809173] [<c0444a0a>] hub_thread+0x3a/0x140
[ 95.809184] [<c0167a60>] ? autoremove_wake_function+0x0/0x50
[ 95.809197] [<c04449d0>] ? hub_thread+0x0/0x140
[ 95.809208] [<c01677d4>] kthread+0x74/0x80
[ 95.809219] [<c0167760>] ? kthread+0x0/0x80
[ 95.809231] [<c0104087>] kernel_thread_helper+0x7/0x10
[ 95.809239] rtl819xU:=============>wlan driver to be removed
[ 95.809242]
[ 95.821101] rtl819xU:wlan driver removed
[ 95.821104]
[ 98.076074] usb 1-2: new high speed USB device using ehci_hcd and address 4
[ 98.211141] usb 1-2: configuration #1 chosen from 1 choice
[ 98.211915] ==>ep_num:4, in_ep_num:1, out_ep_num:3
[ 98.211921] ==>RtInPipes:3
[ 98.211928] ==>RtOutPipes:4 6 13
[ 98.211938] ==>txqueue_to_outpipemap for BK, BE, VI, VO, HCCA, TXCMD, MGNT, HIGH, BEACON:
[ 98.211944] 1 1 0 0 2 2 2 2 2
[ 98.454173] Dot11d_Init()
[ 487.161810] Registered led device: iwl-phy0::radio
[ 487.161907] Registered led device: iwl-phy0::assoc
[ 487.161954] Registered led device: iwl-phy0::RX
[ 487.161998] Registered led device: iwl-phy0::TX
[ 487.177970] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 487.202844] rtl819xU: --->FirmwareDownload92S()
[ 487.202851]
[ 487.202862] usb 1-2: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 487.206722] rtl819xU:request firmware fail!
[ 487.206725]
[ 487.207148] rtl819xU:Firmware Download Fail!!a
[ 487.207151]
[ 487.220088] rtl819xU: --->FirmwareDownload92S()
[ 487.220093]
[ 487.220104] usb 1-2: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 487.223478] rtl819xU:request firmware fail!
[ 487.223481]
[ 487.223841] rtl819xU:Firmware Download Fail!!a
[ 487.223844]
[ 487.223850] rtl819xU:ERR!!! _rtl8192_up(): initialization is failed!
[ 487.223853]
[ 487.365064] usb 4-1: new full speed USB device using uhci_hcd and address 2
[ 487.680284] usb 4-1: configuration #1 chosen from 1 choice
[ 487.718326] Bluetooth: Core ver 2.15
[ 487.720993] NET: Registered protocol family 31
[ 487.720997] Bluetooth: HCI device and connection manager initialized
[ 487.721001] Bluetooth: HCI socket layer initialized
[ 487.723658] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 487.723815] usbcore: registered new interface driver btusb
[ 487.753844] Bluetooth: L2CAP ver 2.14
[ 487.753849] Bluetooth: L2CAP socket layer initialized
[ 487.762053] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 487.762058] Bluetooth: BNEP filters: protocol multicast
[ 487.778598] Bridge firewalling registered
[ 487.810317] Bluetooth: SCO (Voice Link) ver 0.6
[ 487.810322] Bluetooth: SCO socket layer initialized
[ 493.411177] Bluetooth: RFCOMM TTY layer initialized
[ 493.411188] Bluetooth: RFCOMM socket layer initialized
[ 493.411193] Bluetooth: RFCOMM ver 1.11
[ 497.533918] wlan0: deauthenticating from 00:90:d0:f0:54:82 by local choice (reason=3)
[ 497.535188] wlan0: direct probe to AP 00:90:d0:f0:54:82 (try 1)
[ 497.537475] wlan0: direct probe responded
[ 497.537479] wlan0: authenticate with AP 00:90:d0:f0:54:82 (try 1)
[ 497.539453] wlan0: authenticated
[ 497.539471] wlan0: associate with AP 00:90:d0:f0:54:82 (try 1)
[ 497.542071] wlan0: RX AssocResp from 00:90:d0:f0:54:82 (capab=0x411 status=0 aid=1)
[ 497.542076] wlan0: associated
[ 497.543740] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 498.598523] padlock: VIA PadLock not detected.
[ 507.608035] wlan0: no IPv6 routers present
[ 582.902090] usb 1-2: USB disconnect, address 4
[ 582.932099] rtl819xU:=============>wlan driver to be removed
[ 582.932106]
[ 582.943030] rtl819xU:wlan driver removed
[ 582.943032]
[ 599.516376] lo: Disabled Privacy Extensions
[ 648.088870] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
[ 863.955851] CE: hpet increasing min_delta_ns to 15000 nsec
[ 864.056958] CE: hpet increasing min_delta_ns to 22500 nsec
[ 2066.988127] usb 1-2: new high speed USB device using ehci_hcd and address 6
[ 2067.127094] usb 1-2: configuration #1 chosen from 1 choice
[ 2067.133090] ==>ep_num:4, in_ep_num:1, out_ep_num:3
[ 2067.133094] ==>RtInPipes:3
[ 2067.133097] ==>RtOutPipes:4 6 13
[ 2067.133102] ==>txqueue_to_outpipemap for BK, BE, VI, VO, HCCA, TXCMD, MGNT, HIGH, BEACON:
[ 2067.133105] 1 1 0 0 2 2 2 2 2
[ 2067.381981] Dot11d_Init()
[ 2067.384519] ------------[ cut here ]------------
[ 2067.384535] WARNING: at /build/buildd/linux-2.6.32/fs/proc/generic.c:590 proc_register+0x103/0x1e0()
[ 2067.384539] Hardware name: F3JC
[ 2067.384542] proc_dir_entry 'rtl819xU/wlan1' already registered
[ 2067.384546] Modules linked in: aes_i586 aes_generic rfcomm sco bridge stp bnep l2cap btusb bluetooth binfmt_misc ppdev snd_atiixp_modem snd_via82xx_modem snd_intel8x0m snd_ac97_codec snd_hda_codec_si3054 snd_hda_codec_realtek ac97_bus snd_hda_intel snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss snd_pcm arc4 snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device iwl3945 stkwebcam joydev snd iwlcore videodev r8192s_usb(C) nvidia(P) fbcon tileblit font bitblit softcursor soundcore v4l1_compat video output mac80211 asus_laptop sdhci_pci sdhci ricoh_mmc led_class cfg80211 psmouse snd_page_alloc intel_agp serio_raw vga16fb vgastate agpgart lp parport ohci1394 ieee1394 r8169 mii
[ 2067.384648] Pid: 30, comm: khubd Tainted: P WC 2.6.32-25-generic #44-Ubuntu
[ 2067.384652] Call Trace:
[ 2067.384662] [<c014c6e2>] warn_slowpath_common+0x72/0xa0
[ 2067.384668] [<c02523d3>] ? proc_register+0x103/0x1e0
[ 2067.384674] [<c02523d3>] ? proc_register+0x103/0x1e0
[ 2067.384679] [<c014c75b>] warn_slowpath_fmt+0x2b/0x30
[ 2067.384685] [<c02523d3>] proc_register+0x103/0x1e0
[ 2067.384692] [<c02529c9>] create_proc_entry+0x59/0xa0
[ 2067.384715] [<f9b6ea15>] rtl8192_proc_init_one+0x25/0x460 [r8192s_usb]
[ 2067.384723] [<c04c7f0f>] ? register_netdev+0x3f/0x50
[ 2067.384742] [<f9b863be>] rtl8192_usb_probe+0x148/0x191 [r8192s_usb]
[ 2067.384750] [<c044ba40>] usb_probe_interface+0xc0/0x180
[ 2067.384756] [<c0260ba7>] ? sysfs_create_link+0x17/0x20
[ 2067.384768] [<c03e7e5d>] really_probe+0x4d/0x140
[ 2067.384775] [<c03ee76e>] ? pm_runtime_barrier+0x4e/0xc0
[ 2067.384781] [<c03e7f8c>] driver_probe_device+0x3c/0x60
[ 2067.384787] [<c03e8089>] __device_attach+0x49/0x60
[ 2067.384794] [<c03e71b3>] bus_for_each_drv+0x53/0x80
[ 2067.384799] [<c03e8152>] device_attach+0x72/0x90
[ 2067.384804] [<c03e8040>] ? __device_attach+0x0/0x60
[ 2067.384810] [<c03e6ff5>] bus_probe_device+0x25/0x40
[ 2067.384816] [<c03e5a74>] device_add+0x274/0x430
[ 2067.384823] [<c034d4e4>] ? kobject_set_name_vargs+0x64/0x70
[ 2067.384829] [<c044a377>] usb_set_configuration+0x417/0x690
[ 2067.384836] [<c0452d3e>] generic_probe+0x3e/0xb0
[ 2067.384842] [<c0260ba7>] ? sysfs_create_link+0x17/0x20
[ 2067.384847] [<c044a6a4>] usb_probe_device+0x24/0x30
[ 2067.384852] [<c03e7e5d>] really_probe+0x4d/0x140
[ 2067.384858] [<c03ee76e>] ? pm_runtime_barrier+0x4e/0xc0
[ 2067.384864] [<c03e7f8c>] driver_probe_device+0x3c/0x60
[ 2067.384869] [<c03e8089>] __device_attach+0x49/0x60
[ 2067.384875] [<c03e71b3>] bus_for_each_drv+0x53/0x80
[ 2067.384880] [<c03e8152>] device_attach+0x72/0x90
[ 2067.384885] [<c03e8040>] ? __device_attach+0x0/0x60
[ 2067.384891] [<c03e6ff5>] bus_probe_device+0x25/0x40
[ 2067.384896] [<c03e5a74>] device_add+0x274/0x430
[ 2067.384904] [<c04430a6>] usb_new_device+0x56/0xc0
[ 2067.384910] [<c0443bbf>] hub_port_connect_change+0x53f/0x890
[ 2067.384916] [<c0449325>] ? usb_control_msg+0xd5/0x130
[ 2067.384922] [<c0441160>] ? clear_port_feature+0x50/0x60
[ 2067.384928] [<c04446b5>] hub_events+0x1f5/0x510
[ 2067.384935] [<c0167bcf>] ? finish_wait+0x4f/0x70
[ 2067.384940] [<c0444a0a>] hub_thread+0x3a/0x140
[ 2067.384946] [<c0167a60>] ? autoremove_wake_function+0x0/0x50
[ 2067.384951] [<c04449d0>] ? hub_thread+0x0/0x140
[ 2067.384957] [<c01677d4>] kthread+0x74/0x80
[ 2067.384962] [<c0167760>] ? kthread+0x0/0x80
[ 2067.384968] [<c0104087>] kernel_thread_helper+0x7/0x10
[ 2067.384973] ---[ end trace f103cd354dfa62c9 ]---
[ 2067.411592] rtl819xU: --->FirmwareDownload92S()
[ 2067.411596]
[ 2067.411604] usb 1-2: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 2067.415709] rtl819xU:request firmware fail!
[ 2067.415711]
[ 2067.417098] rtl819xU:Firmware Download Fail!!a
[ 2067.417100]
[ 2067.427466] rtl819xU: --->FirmwareDownload92S()
[ 2067.427470]
[ 2067.427478] usb 1-2: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 2067.439262] rtl819xU:request firmware fail!
[ 2067.439264]
[ 2067.440224] rtl819xU:Firmware Download Fail!!a
[ 2067.440226]
[ 2067.440231] rtl819xU:ERR!!! _rtl8192_up(): initialization is failed!
[ 2067.440232]
[ 2067.453221] rtl819xU: --->FirmwareDownload92S()
[ 2067.453223]
[ 2067.453230] usb 1-2: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 2067.465310] rtl819xU:request firmware fail!
[ 2067.465312]
[ 2067.465959] rtl819xU:Firmware Download Fail!!a
[ 2067.465961]
[ 2067.479219] rtl819xU: --->FirmwareDownload92S()
[ 2067.479223]
[ 2067.479231] usb 1-2: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 2067.493245] rtl819xU:request firmware fail!
[ 2067.493247]
[ 2067.493472] rtl819xU:Firmware Download Fail!!a
[ 2067.493473]
[ 2067.493477] rtl819xU:ERR!!! _rtl8192_up(): initialization is failed!
[ 2067.493478]
[ 2071.304883] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 2071.335184] ISOFS: changing to secondary root
[ 2096.909071] ndiswrapper version 1.55 loaded (smp=yes, preempt=no)
[ 2096.946526] usbcore: registered new interface driver ndiswrapper
[ 2108.938564] iwl3945 0000:03:00.0: Card state received: HW:Kill SW:On
[ 2108.938590] iwl3945 0000:03:00.0: Error sending REPLY_SCAN_ABORT_CMD: enqueue_hcmd failed: -5
[ 2108.948150] wlan0: deauthenticating from 00:90:d0:f0:54:82 by local choice (reason=3)
[ 2108.988173] iwl3945 0000:03:00.0: Error sending REPLY_LEDS_CMD: enqueue_hcmd failed: -5
[ 2109.004341] iwl3945 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x040003DD
[ 2109.161144] usb 4-1: USB disconnect, address 2
[ 2109.161784] btusb_intr_complete: hci0 urb ef490000 failed to resubmit (19)
[ 2109.161809] btusb_bulk_complete: hci0 urb ef490f00 failed to resubmit (19)
[ 2109.162787] btusb_bulk_complete: hci0 urb ef490780 failed to resubmit (19)
[ 2109.163238] btusb_send_frame: hci0 urb ef496080 submission failed
[ 2487.844072] usb 4-1: new full speed USB device using uhci_hcd and address 3
[ 2488.154370] usb 4-1: configuration #1 chosen from 1 choice
[ 2489.189988] Registered led device: iwl-phy0::radio
[ 2489.190090] Registered led device: iwl-phy0::assoc
[ 2489.190140] Registered led device: iwl-phy0::RX
[ 2489.190187] Registered led device: iwl-phy0::TX
[ 2489.206754] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2489.219660] rtl819xU: --->FirmwareDownload92S()
[ 2489.219667]
[ 2489.219678] usb 1-2: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 2489.224611] rtl819xU:request firmware fail!
[ 2489.224616]
[ 2489.224797] rtl819xU:Firmware Download Fail!!a
[ 2489.224800]
[ 2489.234149] rtl819xU: --->FirmwareDownload92S()
[ 2489.234154]
[ 2489.234162] usb 1-2: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 2489.241315] rtl819xU:request firmware fail!
[ 2489.241317]
[ 2489.242507] rtl819xU:Firmware Download Fail!!a
[ 2489.242509]
[ 2489.242514] rtl819xU:ERR!!! _rtl8192_up(): initialization is failed!
[ 2489.242516]
[ 2493.432431] hci_cmd_task: hci0 command tx timeout
[ 2499.568313] wlan0: deauthenticating from 00:90:d0:f0:54:82 by local choice (reason=3)
[ 2499.568370] wlan0: direct probe to AP 00:90:d0:f0:54:82 (try 1)
[ 2499.571473] wlan0: direct probe responded
[ 2499.571480] wlan0: authenticate with AP 00:90:d0:f0:54:82 (try 1)
[ 2499.573229] wlan0: authenticated
[ 2499.573255] wlan0: associate with AP 00:90:d0:f0:54:82 (try 1)
[ 2499.575769] wlan0: RX AssocResp from 00:90:d0:f0:54:82 (capab=0x411 status=0 aid=1)
[ 2499.575773] wlan0: associated
[ 2499.579803] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2510.152047] wlan0: no IPv6 routers present
[ 2933.914079] usb 1-2: USB disconnect, address 6
[ 2933.945755] rtl819xU:=============>wlan driver to be removed
[ 2933.945762]
[ 2933.958823] rtl819xU:wlan driver removed
[ 2933.958826]
[ 2937.807099] iwl3945 0000:03:00.0: Card state received: HW:Kill SW:On
[ 2937.820142] wlan0: deauthenticating from 00:90:d0:f0:54:82 by local choice (reason=3)
[ 2937.864150] iwl3945 0000:03:00.0: Error sending REPLY_LEDS_CMD: enqueue_hcmd failed: -5
[ 2937.876691] iwl3945 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x040003DD
[ 2937.976137] usb 4-1: USB disconnect, address 3
[ 2937.976943] btusb_intr_complete: hci0 urb f1307d00 failed to resubmit (19)
[ 2937.976966] btusb_bulk_complete: hci0 urb ef496880 failed to resubmit (19)
[ 2937.977930] btusb_bulk_complete: hci0 urb ef496e80 failed to resubmit (19)
[ 2939.208084] usb 4-1: new full speed USB device using uhci_hcd and address 4
[ 2939.457264] usb 4-1: configuration #1 chosen from 1 choice
[ 2940.207656] Registered led device: iwl-phy0::radio
[ 2940.216052] Registered led device: iwl-phy0::assoc
[ 2940.216307] Registered led device: iwl-phy0::RX
[ 2940.219113] Registered led device: iwl-phy0::TX
[ 2940.229940] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2950.559389] wlan0: deauthenticating from 00:90:d0:f0:54:82 by local choice (reason=3)
[ 2950.559600] wlan0: direct probe to AP 00:90:d0:f0:54:82 (try 1)
[ 2950.562594] wlan0: direct probe responded
[ 2950.562603] wlan0: authenticate with AP 00:90:d0:f0:54:82 (try 1)
[ 2950.564508] wlan0: authenticated
[ 2950.564542] wlan0: associate with AP 00:90:d0:f0:54:82 (try 1)
[ 2950.567070] wlan0: RX AssocResp from 00:90:d0:f0:54:82 (capab=0x411 status=0 aid=1)
[ 2950.567076] wlan0: associated
[ 2950.570214] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2954.184106] usb 1-1: new high speed USB device using ehci_hcd and address 9
[ 2954.319024] usb 1-1: configuration #1 chosen from 1 choice
[ 2954.325972] ==>ep_num:4, in_ep_num:1, out_ep_num:3
[ 2954.325979] ==>RtInPipes:3
[ 2954.325987] ==>RtOutPipes:4 6 13
[ 2954.325997] ==>txqueue_to_outpipemap for BK, BE, VI, VO, HCCA, TXCMD, MGNT, HIGH, BEACON:
[ 2954.326003] 1 1 0 0 2 2 2 2 2
[ 2954.564476] Dot11d_Init()
[ 2954.566586] ------------[ cut here ]------------
[ 2954.566604] WARNING: at /build/buildd/linux-2.6.32/fs/proc/generic.c:590 proc_register+0x103/0x1e0()
[ 2954.566611] Hardware name: F3JC
[ 2954.566617] proc_dir_entry 'rtl819xU/wlan1' already registered
[ 2954.566622] Modules linked in: ndiswrapper nls_utf8 isofs aes_i586 aes_generic rfcomm sco bridge stp bnep l2cap btusb bluetooth binfmt_misc ppdev snd_atiixp_modem snd_via82xx_modem snd_intel8x0m snd_ac97_codec snd_hda_codec_si3054 snd_hda_codec_realtek ac97_bus snd_hda_intel snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss snd_pcm arc4 snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device iwl3945 stkwebcam joydev snd iwlcore videodev r8192s_usb(C) nvidia(P) fbcon tileblit font bitblit softcursor soundcore v4l1_compat video output mac80211 asus_laptop sdhci_pci sdhci ricoh_mmc led_class cfg80211 psmouse snd_page_alloc intel_agp serio_raw vga16fb vgastate agpgart lp parport ohci1394 ieee1394 r8169 mii
[ 2954.566789] Pid: 30, comm: khubd Tainted: P WC 2.6.32-25-generic #44-Ubuntu
[ 2954.566796] Call Trace:
[ 2954.566809] [<c014c6e2>] warn_slowpath_common+0x72/0xa0
[ 2954.566820] [<c02523d3>] ? proc_register+0x103/0x1e0
[ 2954.566829] [<c02523d3>] ? proc_register+0x103/0x1e0
[ 2954.566839] [<c014c75b>] warn_slowpath_fmt+0x2b/0x30
[ 2954.566849] [<c02523d3>] proc_register+0x103/0x1e0
[ 2954.566859] [<c02529c9>] create_proc_entry+0x59/0xa0
[ 2954.566896] [<f9b6ea15>] rtl8192_proc_init_one+0x25/0x460 [r8192s_usb]
[ 2954.566912] [<c04c7f0f>] ? register_netdev+0x3f/0x50
[ 2954.566945] [<f9b863be>] rtl8192_usb_probe+0x148/0x191 [r8192s_usb]
[ 2954.566959] [<c044ba40>] usb_probe_interface+0xc0/0x180
[ 2954.566972] [<c0260ba7>] ? sysfs_create_link+0x17/0x20
[ 2954.566991] [<c03e7e5d>] really_probe+0x4d/0x140
[ 2954.567004] [<c03ee76e>] ? pm_runtime_barrier+0x4e/0xc0
[ 2954.567017] [<c03e7f8c>] driver_probe_device+0x3c/0x60
[ 2954.567030] [<c03e8089>] __device_attach+0x49/0x60
[ 2954.567044] [<c03e71b3>] bus_for_each_drv+0x53/0x80
[ 2954.567055] [<c03e8152>] device_attach+0x72/0x90
[ 2954.567067] [<c03e8040>] ? __device_attach+0x0/0x60
[ 2954.567079] [<c03e6ff5>] bus_probe_device+0x25/0x40
[ 2954.567092] [<c03e5a74>] device_add+0x274/0x430
[ 2954.567105] [<c034d4e4>] ? kobject_set_name_vargs+0x64/0x70
[ 2954.567118] [<c044a377>] usb_set_configuration+0x417/0x690
[ 2954.567132] [<c0452d3e>] generic_probe+0x3e/0xb0
[ 2954.567145] [<c0260ba7>] ? sysfs_create_link+0x17/0x20
[ 2954.567157] [<c044a6a4>] usb_probe_device+0x24/0x30
[ 2954.567169] [<c03e7e5d>] really_probe+0x4d/0x140
[ 2954.567181] [<c03ee76e>] ? pm_runtime_barrier+0x4e/0xc0
[ 2954.567193] [<c03e7f8c>] driver_probe_device+0x3c/0x60
[ 2954.567205] [<c03e8089>] __device_attach+0x49/0x60
[ 2954.567218] [<c03e71b3>] bus_for_each_drv+0x53/0x80
[ 2954.567229] [<c03e8152>] device_attach+0x72/0x90
[ 2954.567240] [<c03e8040>] ? __device_attach+0x0/0x60
[ 2954.567253] [<c03e6ff5>] bus_probe_device+0x25/0x40
[ 2954.567265] [<c03e5a74>] device_add+0x274/0x430
[ 2954.567280] [<c04430a6>] usb_new_device+0x56/0xc0
[ 2954.567293] [<c0443bbf>] hub_port_connect_change+0x53f/0x890
[ 2954.567305] [<c0449325>] ? usb_control_msg+0xd5/0x130
[ 2954.567318] [<c0441160>] ? clear_port_feature+0x50/0x60
[ 2954.567331] [<c04446b5>] hub_events+0x1f5/0x510
[ 2954.567344] [<c0167bcf>] ? finish_wait+0x4f/0x70
[ 2954.567356] [<c0444a0a>] hub_thread+0x3a/0x140
[ 2954.567368] [<c0167a60>] ? autoremove_wake_function+0x0/0x50
[ 2954.567381] [<c04449d0>] ? hub_thread+0x0/0x140
[ 2954.567392] [<c01677d4>] kthread+0x74/0x80
[ 2954.567403] [<c0167760>] ? kthread+0x0/0x80
[ 2954.567416] [<c0104087>] kernel_thread_helper+0x7/0x10
[ 2954.567425] ---[ end trace f103cd354dfa62ca ]---
[ 2955.030622] rtl819xU: --->FirmwareDownload92S()
[ 2955.030626]
[ 2955.030633] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 2955.032786] rtl819xU:request firmware fail!
[ 2955.032788]
[ 2955.033965] rtl819xU:Firmware Download Fail!!a
[ 2955.033968]
[ 2955.042376] rtl819xU: --->FirmwareDownload92S()
[ 2955.042379]
[ 2955.042386] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 2955.062310] rtl819xU:request firmware fail!
[ 2955.062312]
[ 2955.062908] rtl819xU:Firmware Download Fail!!a
[ 2955.062909]
[ 2955.062913] rtl819xU:ERR!!! _rtl8192_up(): initialization is failed!
[ 2955.062915]
[ 2955.077285] rtl819xU: --->FirmwareDownload92S()
[ 2955.077289]
[ 2955.077297] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 2955.107394] rtl819xU:request firmware fail!
[ 2955.107396]
[ 2955.107897] rtl819xU:Firmware Download Fail!!a
[ 2955.107899]
[ 2955.118261] rtl819xU: --->FirmwareDownload92S()
[ 2955.118266]
[ 2955.118275] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 2955.124045] rtl819xU:request firmware fail!
[ 2955.124047]
[ 2955.124333] rtl819xU:Firmware Download Fail!!a
[ 2955.124335]
[ 2955.124338] rtl819xU:ERR!!! _rtl8192_up(): initialization is failed!
[ 2955.124340]
[ 2961.392034] wlan0: no IPv6 routers present
[ 3500.123848] usbcore: registered new interface driver r871x_usb_drv
[ 3512.384490] rtl819xU: --->FirmwareDownload92S()
[ 3512.384498]
[ 3512.384510] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 3512.388781] rtl819xU:request firmware fail!
[ 3512.388784]
[ 3512.389596] rtl819xU:Firmware Download Fail!!a
[ 3512.389599]
[ 3512.402958] rtl819xU: --->FirmwareDownload92S()
[ 3512.402960]
[ 3512.402967] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 3512.418151] rtl819xU:request firmware fail!
[ 3512.418153]
[ 3512.418493] rtl819xU:Firmware Download Fail!!a
[ 3512.418495]
[ 3512.418498] rtl819xU:ERR!!! _rtl8192_up(): initialization is failed!
[ 3512.418500]
[ 3577.849483] rtl819xU: --->FirmwareDownload92S()
[ 3577.849490]
[ 3577.849502] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 3577.853257] rtl819xU:request firmware fail!
[ 3577.853261]
[ 3577.853491] rtl819xU:Firmware Download Fail!!a
[ 3577.853495]
[ 3577.867471] rtl819xU: --->FirmwareDownload92S()
[ 3577.867480]
[ 3577.867493] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 3577.882768] rtl819xU:request firmware fail!
[ 3577.882770]
[ 3577.883926] rtl819xU:Firmware Download Fail!!a
[ 3577.883929]
[ 3577.883934] rtl819xU:ERR!!! _rtl8192_up(): initialization is failed!
[ 3577.883935]
[ 3584.065098] rtl819xU: --->FirmwareDownload92S()
[ 3584.065105]
[ 3584.065117] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 3584.069613] rtl819xU:request firmware fail!
[ 3584.069615]
[ 3584.069851] rtl819xU:Firmware Download Fail!!a
[ 3584.069853]
[ 3584.077091] rtl819xU: --->FirmwareDownload92S()
[ 3584.077094]
[ 3584.077101] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 3584.089791] rtl819xU:request firmware fail!
[ 3584.089793]
[ 3584.090322] rtl819xU:Firmware Download Fail!!a
[ 3584.090324]
[ 3584.090327] rtl819xU:ERR!!! _rtl8192_up(): initialization is failed!
[ 3584.090329]
[ 4654.638016] usbcore: deregistering interface driver ndiswrapper
[ 4654.662128] ndiswrapper version 1.55 loaded (smp=yes, preempt=no)
[ 4654.673118] usbcore: registered new interface driver ndiswrapper
[ 4689.449001] rtl819xU: --->FirmwareDownload92S()
[ 4689.449008]
[ 4689.449020] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 4689.452480] rtl819xU:request firmware fail!
[ 4689.452483]
[ 4689.452811] rtl819xU:Firmware Download Fail!!a
[ 4689.452813]
[ 4689.462361] rtl819xU: --->FirmwareDownload92S()
[ 4689.462363]
[ 4689.462369] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 4689.472060] rtl819xU:request firmware fail!
[ 4689.472062]
[ 4689.473679] rtl819xU:Firmware Download Fail!!a
[ 4689.473681]
[ 4689.473686] rtl819xU:ERR!!! _rtl8192_up(): initialization is failed!
[ 4689.473687]
[ 4825.284780] iwl3945 0000:03:00.0: Card state received: HW:Kill SW:On
[ 4825.296159] wlan0: deauthenticating from 00:90:d0:f0:54:82 by local choice (reason=3)
[ 4825.340136] iwl3945 0000:03:00.0: Error sending REPLY_LEDS_CMD: enqueue_hcmd failed: -5
[ 4825.352210] iwl3945 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x040003DD
[ 4825.504114] usb 4-1: USB disconnect, address 4
[ 4933.658163] rtl819xU: --->FirmwareDownload92S()
[ 4933.658168]
[ 4933.658179] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 4933.660312] rtl819xU:request firmware fail!
[ 4933.660313]
[ 4933.660657] rtl819xU:Firmware Download Fail!!a
[ 4933.660658]
[ 4933.671011] rtl819xU: --->FirmwareDownload92S()
[ 4933.671015]
[ 4933.671023] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 4933.677934] rtl819xU:request firmware fail!
[ 4933.677936]
[ 4933.679142] rtl819xU:Firmware Download Fail!!a
[ 4933.679144]
[ 4933.679150] rtl819xU:ERR!!! _rtl8192_up(): initialization is failed!
[ 4933.679151]
[ 5061.760069] usb 4-1: new full speed USB device using uhci_hcd and address 5
[ 5062.078348] usb 4-1: configuration #1 chosen from 1 choice
[ 5062.190185] Registered led device: iwl-phy0::radio
[ 5062.190510] Registered led device: iwl-phy0::assoc
[ 5062.190756] Registered led device: iwl-phy0::RX
[ 5062.190981] Registered led device: iwl-phy0::TX
[ 5062.200934] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 5062.216285] rtl819xU: --->FirmwareDownload92S()
[ 5062.216289]
[ 5062.216297] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 5062.220847] rtl819xU:request firmware fail!
[ 5062.220849]
[ 5062.221123] rtl819xU:Firmware Download Fail!!a
[ 5062.221125]
[ 5062.230403] rtl819xU: --->FirmwareDownload92S()
[ 5062.230408]
[ 5062.230415] usb 1-1: firmware: requesting RTL8192SU/rtl8192sfw.bin
[ 5062.246370] rtl819xU:request firmware fail!
[ 5062.246373]
[ 5062.247375] rtl819xU:Firmware Download Fail!!a
[ 5062.247377]
[ 5062.247383] rtl819xU:ERR!!! _rtl8192_up(): initialization is failed!
[ 5062.247385]
[ 5062.571616] hci_cmd_task: hci0 command tx timeout
[ 5072.548975] wlan0: deauthenticating from 00:90:d0:f0:54:82 by local choice (reason=3)
[ 5072.549494] wlan0: direct probe to AP 00:90:d0:f0:54:82 (try 1)
[ 5072.552831] wlan0: direct probe responded
[ 5072.552843] wlan0: authenticate with AP 00:90:d0:f0:54:82 (try 1)
[ 5072.554696] wlan0: authenticated
[ 5072.554752] wlan0: associate with AP 00:90:d0:f0:54:82 (try 1)
[ 5072.557317] wlan0: RX AssocResp from 00:90:d0:f0:54:82 (capab=0x411 status=0 aid=1)
[ 5072.557327] wlan0: associated
[ 5072.560416] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 5082.864023] wlan0: no IPv6 routers present

Ελπίζω να καταφέρουμε να το λειτουργήσουμε !

[jim137]

Δόσε το αποτέλεσμα

Κώδικας: Επιλογή όλων

sudo iwlist scan
rfkill list


μέσα σε

Κώδικας: Επιλογή όλων

[code][/code]

Κάνε και ένα κόπο να διαβάσεις και αυτό viewtopic.php?f=10&t=279