Προβλημα με WIRLESS crypto air data 150 s2 stick

[Dimitrios.gr]

Βάλε ένα Ethernet καλώδιο και κάνε εγκατάσταση

Κώδικας: Επιλογή όλων

sudo apt-get install linux-backports-modules-wireless-3.3-lucid-generic

επανεκκίνηση , βγάζεις το καλώδιο Ethernet , συνδέεις το Usb-stick περιμένεις 10 δευτερόλεπτα και ανοίγεις ένα τερματικό και δίνεις

Κώδικας: Επιλογή όλων

dmesg | tail -n 30

να δούμε τα αποτελέσματα.

Επίσης δεν βλέπω καλό σήμα ,

Κώδικας: Επιλογή όλων

Bit Rate=1 Mb/s
RTS thr:off Fragment thr:off
Link Quality=10/100

είναι μακριά το router από το Laptop ;
Μήπως να δοκίμαζες να αλλάξεις και κανάλι εκπομπής ;

ναι συνδέθηκε!!!

Κώδικας: Επιλογή όλων

[ 122.884077] ata2.01: cmd a0/00:00:00:00:00/00:00:00:00:00/b0 tag 0
[ 122.884078] res 51/20:03:00:00:00/00:00:00:00:00/b0 Emask 0x5 (timeout)
[ 122.884083] ata2.01: status: { DRDY ERR }
[ 122.884113] ata2: soft resetting link
[ 128.160042] ata2.01: qc timeout (cmd 0xa1)
[ 128.160053] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 128.160057] ata2.01: revalidation failed (errno=-5)
[ 133.200028] ata2: link is slow to respond, please be patient (ready=0)
[ 135.506829] DeQueueRunning[0]= TRUE!
[ 138.184032] ata2: device not ready (errno=-16), forcing hardreset
[ 138.184044] ata2: soft resetting link
[ 148.396041] ata2.01: qc timeout (cmd 0xa1)
[ 148.396051] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 148.396055] ata2.01: revalidation failed (errno=-5)
[ 153.436018] ata2: link is slow to respond, please be patient (ready=0)
[ 158.421021] ata2: device not ready (errno=-16), forcing hardreset
[ 158.421034] ata2: soft resetting link
[ 170.872053] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 188.633051] ata2.01: qc timeout (cmd 0xa1)
[ 188.633062] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 188.633067] ata2.01: revalidation failed (errno=-5)
[ 188.633072] ata2.01: disabled
[ 193.673023] ata2: link is slow to respond, please be patient (ready=0)
[ 198.656019] ata2: device not ready (errno=-16), forcing hardreset
[ 198.656032] ata2: soft resetting link
[ 198.823353] ata2: EH complete
[ 250.865559] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 301.868677] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 301.869025] ==>rt_ioctl_siwfreq::SIOCSIWFREQ[cmd=0x8b04] (Channel=1)
[ 350.873064] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173

[Learner]

Ωραία , πάτα το πράσινο τικ , αλλά δώσε και τα αποτελέσματα του dmesg , να δούμε τα μηνύματα.

[Dimitrios.gr]

Ωραία , πάτα το πράσινο τικ , αλλά δώσε και τα αποτελέσματα του dmesg , να δούμε τα μηνύματα.

Κώδικας: Επιλογή όλων

[ 0.192078] pci 0000:00:00.0: reg 10 32bit mmio pref: [0xf8000000-0xfbffffff]
[ 0.192559] pci 0000:00:01.0: supports D1
[ 0.192616] pci 0000:00:09.0: reg 10 io port: [0xec00-0xecff]
[ 0.192627] pci 0000:00:09.0: reg 14 32bit mmio: [0xffefff00-0xffefffff]
[ 0.192660] pci 0000:00:09.0: reg 30 32bit mmio pref: [0xffec0000-0xffedffff]
[ 0.192698] pci 0000:00:09.0: supports D1 D2
[ 0.192703] pci 0000:00:09.0: PME# supported from D1 D2 D3hot
[ 0.192710] pci 0000:00:09.0: PME# disabled
[ 0.192787] pci 0000:00:0f.0: reg 20 io port: [0xfc00-0xfc0f]
[ 0.192898] pci 0000:00:10.0: reg 20 io port: [0xdc00-0xdc1f]
[ 0.192944] pci 0000:00:10.0: supports D1 D2
[ 0.192949] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.192956] pci 0000:00:10.0: PME# disabled
[ 0.193021] pci 0000:00:10.1: reg 20 io port: [0xe000-0xe01f]
[ 0.193068] pci 0000:00:10.1: supports D1 D2
[ 0.193072] pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.193079] pci 0000:00:10.1: PME# disabled
[ 0.193183] pci 0000:00:10.2: reg 20 io port: [0xe400-0xe41f]
[ 0.193230] pci 0000:00:10.2: supports D1 D2
[ 0.193235] pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.193242] pci 0000:00:10.2: PME# disabled
[ 0.193307] pci 0000:00:10.3: reg 20 io port: [0xe800-0xe81f]
[ 0.193354] pci 0000:00:10.3: supports D1 D2
[ 0.193359] pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.193366] pci 0000:00:10.3: PME# disabled
[ 0.193410] pci 0000:00:10.4: reg 10 32bit mmio: [0xffeffd00-0xffeffdff]
[ 0.193479] pci 0000:00:10.4: supports D1 D2
[ 0.193483] pci 0000:00:10.4: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.193490] pci 0000:00:10.4: PME# disabled
[ 0.193575] HPET not enabled in BIOS. You might try hpet=force boot option
[ 0.193688] pci 0000:00:11.5: reg 10 io port: [0xd800-0xd8ff]
[ 0.193785] pci 0000:00:11.5: supports D1 D2
[ 0.193835] pci 0000:00:12.0: reg 10 io port: [0xd400-0xd4ff]
[ 0.193846] pci 0000:00:12.0: reg 14 32bit mmio: [0xffeffc00-0xffeffcff]
[ 0.193910] pci 0000:00:12.0: supports D1 D2
[ 0.193914] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.193921] pci 0000:00:12.0: PME# disabled
[ 0.194003] pci 0000:01:00.0: reg 10 32bit mmio pref: [0xe0000000-0xefffffff]
[ 0.194014] pci 0000:01:00.0: reg 14 io port: [0xc800-0xc8ff]
[ 0.194024] pci 0000:01:00.0: reg 18 32bit mmio: [0xffdf0000-0xffdfffff]
[ 0.194048] pci 0000:01:00.0: reg 30 32bit mmio pref: [0xffdc0000-0xffddffff]
[ 0.194093] pci 0000:01:00.0: supports D1 D2
[ 0.194135] pci 0000:01:00.1: reg 10 32bit mmio pref: [0xd0000000-0xdfffffff]
[ 0.194145] pci 0000:01:00.1: reg 14 32bit mmio: [0xffde0000-0xffdeffff]
[ 0.194201] pci 0000:01:00.1: supports D1 D2
[ 0.194263] pci 0000:00:01.0: bridge io port: [0xc000-0xcfff]
[ 0.194270] pci 0000:00:01.0: bridge 32bit mmio: [0xffd00000-0xffdfffff]
[ 0.194278] pci 0000:00:01.0: bridge 32bit mmio pref: [0xb7f00000-0xf7efffff]
[ 0.194290] pci_bus 0000:00: on NUMA node 0
[ 0.194299] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.201274] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.201474] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.201640] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.201805] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 *12 14 15)
[ 0.201971] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.202172] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.202341] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.202510] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.202778] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.202786] vgaarb: loaded
[ 0.203040] SCSI subsystem initialized
[ 0.203331] libata version 3.00 loaded.
[ 0.203443] usbcore: registered new interface driver usbfs
[ 0.203470] usbcore: registered new interface driver hub
[ 0.203528] usbcore: registered new device driver usb
[ 0.203834] ACPI: WMI: Mapper loaded
[ 0.203840] PCI: Using ACPI for IRQ routing
[ 0.204166] NetLabel: Initializing
[ 0.204171] NetLabel: domain hash size = 128
[ 0.204174] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.204198] NetLabel: unlabeled traffic allowed by default
[ 0.204287] Switching to clocksource tsc
[ 0.208085] AppArmor: AppArmor Filesystem Enabled
[ 0.208118] pnp: PnP ACPI init
[ 0.208158] ACPI: bus type pnp registered
[ 0.212703] pnp: PnP ACPI: found 10 devices
[ 0.212717] ACPI: ACPI bus type pnp unregistered
[ 0.212727] PnPBIOS: Disabled by ACPI PNP
[ 0.212778] system 00:01: ioport range 0x290-0x297 has been reserved
[ 0.212785] system 00:01: ioport range 0x3f0-0x3f1 has been reserved
[ 0.212790] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 0.212796] system 00:01: ioport range 0x400-0x40f has been reserved
[ 0.212802] system 00:01: ioport range 0x820-0x821 has been reserved
[ 0.212809] system 00:01: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.247728] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.247736] pci 0000:00:01.0: IO window: 0xc000-0xcfff
[ 0.247745] pci 0000:00:01.0: MEM window: 0xffd00000-0xffdfffff
[ 0.247752] pci 0000:00:01.0: PREFETCH window: 0xb7f00000-0xf7efffff
[ 0.247777] pci 0000:00:01.0: setting latency timer to 64
[ 0.247785] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.247791] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.247796] pci_bus 0000:01: resource 0 io: [0xc000-0xcfff]
[ 0.247802] pci_bus 0000:01: resource 1 mem: [0xffd00000-0xffdfffff]
[ 0.247807] pci_bus 0000:01: resource 2 pref mem [0xb7f00000-0xf7efffff]
[ 0.247884] NET: Registered protocol family 2
[ 0.248079] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.248743] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.248886] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.249026] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.249031] TCP reno registered
[ 0.249171] NET: Registered protocol family 1
[ 0.249211] pci 0000:00:01.0: disabling DAC on VIA PCI bridge
[ 0.249245] alloc irq_desc for 21 on node -1
[ 0.249250] alloc kstat_irqs on node -1
[ 0.249263] pci 0000:00:10.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 0.249284] pci 0000:00:10.0: PCI INT A disabled
[ 0.249300] pci 0000:00:10.1: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 0.249320] pci 0000:00:10.1: PCI INT A disabled
[ 0.249336] pci 0000:00:10.2: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.249356] pci 0000:00:10.2: PCI INT B disabled
[ 0.249371] pci 0000:00:10.3: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.249391] pci 0000:00:10.3: PCI INT B disabled
[ 0.249407] pci 0000:00:10.4: PCI INT C -> GSI 21 (level, low) -> IRQ 21
[ 0.249445] pci 0000:00:10.4: PCI INT C disabled
[ 0.249454] pci 0000:00:11.0: Bypassing VIA 8237 APIC De-Assert Message
[ 0.249469] pci 0000:01:00.0: Boot video device
[ 0.249845] cpufreq-nforce2: No nForce2 chipset.
[ 0.249904] Scanning for low memory corruption every 60 seconds
[ 0.250141] audit: initializing netlink socket (disabled)
[ 0.250160] type=2000 audit(1344878124.247:1): initialized
[ 0.262737] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.266072] VFS: Disk quotas dquot_6.5.2
[ 0.266210] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.267636] fuse init (API version 7.13)
[ 0.267823] msgmni has been set to 977
[ 0.268341] alg: No test for stdrng (krng)
[ 0.268459] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.268466] io scheduler noop registered
[ 0.268470] io scheduler anticipatory registered
[ 0.268474] io scheduler deadline registered
[ 0.268567] io scheduler cfq registered (default)
[ 0.268846] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.268893] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.269108] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.269115] ACPI: Power Button [PWRB]
[ 0.269228] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.269234] ACPI: Power Button [PWRF]
[ 0.269640] processor LNXCPU:00: registered as cooling_device0
[ 0.269732] processor LNXCPU:01: registered as cooling_device1
[ 0.276329] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.276479] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.277114] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.279399] brd: module loaded
[ 0.279548] isapnp: Scanning for PnP cards...
[ 0.280370] loop: module loaded
[ 0.280531] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 0.280819] alloc irq_desc for 20 on node -1
[ 0.280823] alloc kstat_irqs on node -1
[ 0.280837] pata_acpi 0000:00:0f.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.280923] pata_acpi 0000:00:0f.0: PCI INT A disabled
[ 0.281485] Fixed MDIO Bus: probed
[ 0.281549] PPP generic driver version 2.4.2
[ 0.281611] tun: Universal TUN/TAP device driver, 1.6
[ 0.281615] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.281767] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.281794] ehci_hcd 0000:00:10.4: PCI INT C -> GSI 21 (level, low) -> IRQ 21
[ 0.281821] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 0.281892] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
[ 0.281987] ehci_hcd 0000:00:10.4: irq 21, io mem 0xffeffd00
[ 0.291760] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00
[ 0.291956] usb usb1: configuration #1 chosen from 1 choice
[ 0.292009] hub 1-0:1.0: USB hub found
[ 0.292029] hub 1-0:1.0: 8 ports detected
[ 0.292135] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.292165] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.292241] uhci_hcd 0000:00:10.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 0.292256] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 0.292325] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 0.292356] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000dc00
[ 0.292520] usb usb2: configuration #1 chosen from 1 choice
[ 0.292566] hub 2-0:1.0: USB hub found
[ 0.292583] hub 2-0:1.0: 2 ports detected
[ 0.292659] uhci_hcd 0000:00:10.1: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 0.292670] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 0.292733] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 0.292758] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000e000
[ 0.292921] usb usb3: configuration #1 chosen from 1 choice
[ 0.292967] hub 3-0:1.0: USB hub found
[ 0.292983] hub 3-0:1.0: 2 ports detected
[ 0.293063] uhci_hcd 0000:00:10.2: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.293074] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 0.293128] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[ 0.293154] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000e400
[ 0.293321] usb usb4: configuration #1 chosen from 1 choice
[ 0.293366] hub 4-0:1.0: USB hub found
[ 0.293381] hub 4-0:1.0: 2 ports detected
[ 0.293456] uhci_hcd 0000:00:10.3: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.293467] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 0.293520] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
[ 0.293546] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000e800
[ 0.293723] usb usb5: configuration #1 chosen from 1 choice
[ 0.293774] hub 5-0:1.0: USB hub found
[ 0.293790] hub 5-0:1.0: 2 ports detected
[ 0.293936] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 0.293941] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 0.294121] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.294315] mice: PS/2 mouse device common for all mice
[ 0.294504] rtc_cmos 00:03: RTC can wake from S4
[ 0.294579] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.294634] rtc0: alarms up to one year, y3k, 114 bytes nvram
[ 0.294843] device-mapper: uevent: version 1.0.3
[ 0.320119] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 0.329249] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.343915] device-mapper: multipath: version 1.1.0 loaded
[ 0.343922] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.344240] EISA: Probing bus 0 at eisa.0
[ 0.344288] EISA: Detected 0 cards.
[ 0.359671] cpuidle: using governor ladder
[ 0.359677] cpuidle: using governor menu
[ 0.360583] TCP cubic registered
[ 0.360853] NET: Registered protocol family 10
[ 0.362457] NET: Registered protocol family 17
[ 0.362559] Using IPI No-Shortcut mode
[ 0.362735] PM: Resume from disk failed.
[ 0.362760] registered taskstats version 1
[ 0.363171] Magic number: 8:511:289
[ 0.363227] tty tty22: hash matches
[ 0.363317] rtc_cmos 00:03: setting system clock to 2012-08-13 17:15:25 UTC (1344878125)
[ 0.363322] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.363325] EDD information not available.
[ 0.511527] Freeing initrd memory: 7838k freed
[ 0.634023] isapnp: No Plug & Play device found
[ 0.634058] Freeing unused kernel memory: 664k freed
[ 0.635366] Write protecting the kernel text: 4700k
[ 0.635422] Write protecting the kernel read-only data: 1848k
[ 0.662542] udev: starting version 151
[ 0.715641] usb 1-4: new high speed USB device using ehci_hcd and address 3
[ 0.854478] pata_via 0000:00:0f.0: version 0.3.4
[ 0.854531] pata_via 0000:00:0f.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.867564] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 0.867634] scsi0 : pata_via
[ 0.868049] scsi1 : pata_via
[ 0.872039] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
[ 0.872046] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
[ 0.872319] alloc irq_desc for 23 on node -1
[ 0.872324] alloc kstat_irqs on node -1
[ 0.872337] via-rhine 0000:00:12.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.873784] eth0: VIA Rhine II at 0xffeffc00, 00:11:09:84:6f:3e, IRQ 23.
[ 0.874493] eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
[ 0.874976] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 0.875048] 8139cp 0000:00:09.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 0.875141] Floppy drive(s): fd0 is 1.44M
[ 0.876328] usb 1-4: configuration #1 chosen from 1 choice
[ 0.891591] FDC 0 is a post-1991 82077
[ 1.044248] ata1.01: ATA-7: Maxtor 6Y080P0, YAR41BW0, max UDMA/133
[ 1.044253] ata1.01: 160086528 sectors, multi 16: LBA
[ 1.044288] ata1.01: limited to UDMA/33 due to 40-wire cable
[ 1.060130] ata1.01: configured for UDMA/33
[ 1.060310] scsi 0:0:1:0: Direct-Access ATA Maxtor 6Y080P0 YAR4 PQ: 0 ANSI: 5
[ 1.060633] sd 0:0:1:0: Attached scsi generic sg0 type 0
[ 1.060812] sd 0:0:1:0: [sda] 160086528 512-byte logical blocks: (81.9 GB/76.3 GiB)
[ 1.060913] sd 0:0:1:0: [sda] Write Protect is off
[ 1.060918] sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
[ 1.060955] sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.061157] sda: sda1 sda2 < sda5 >
[ 1.085878] sd 0:0:1:0: [sda] Attached SCSI disk
[ 1.119602] usb 2-2: new full speed USB device using uhci_hcd and address 2
[ 1.296650] usb 2-2: configuration #1 chosen from 1 choice
[ 1.345377] ata2.01: ATAPI: SONY DVD RW DW-D22A, BYS1, max UDMA/66
[ 1.360269] ata2.01: configured for UDMA/66
[ 1.361629] scsi 1:0:1:0: CD-ROM SONY DVD RW DW-D22A BYS1 PQ: 0 ANSI: 5
[ 1.365741] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 1.365746] Uniform CD-ROM driver Revision: 3.20
[ 1.365933] sr 1:0:1:0: Attached scsi CD-ROM sr0
[ 1.366070] sr 1:0:1:0: Attached scsi generic sg1 type 5
[ 1.372939] 8139too Fast Ethernet driver 0.9.28
[ 1.373049] alloc irq_desc for 17 on node -1
[ 1.373055] alloc kstat_irqs on node -1
[ 1.373070] 8139too 0000:00:09.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.375171] eth1: RealTek RTL8139 at 0xec00, f8:d1:11:04:c3:f4, IRQ 17
[ 1.384378] usbcore: registered new interface driver hiddev
[ 1.394764] input: Microsoft SideWinder™ Mouse as /devices/pci0000:00/0000:00:10.0/usb2/2-2/2-2:1.0/input/input4
[ 1.395003] generic-usb 0003:045E:0724.0001: input,hidraw0: USB HID v1.11 Mouse [Microsoft SideWinder™ Mouse] on usb-0000:00:10.0-2/input0
[ 1.395057] usbcore: registered new interface driver usbhid
[ 1.395064] usbhid: v2.6:USB HID core driver
[ 1.628359] EXT4-fs (sda5): mounted filesystem with ordered data mode
[ 13.369031] Adding 2928632k swap on /dev/sda1. Priority:-1 extents:1 across:2928632k
[ 13.410681] udev: starting version 151
[ 13.599256] udev: renamed network interface eth0 to eth1
[ 13.622738] udev: renamed network interface eth1_rename to eth0
[ 13.647641] ACPI: resource vt596_smbus [0x400-0x407] conflicts with ACPI region SMOV [0x400-0x406]
[ 13.647648] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 13.656206] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 13.657273] Linux agpgart interface v0.103
[ 13.773491] agpgart: Detected VIA PT880 chipset
[ 13.812431] agpgart-via 0000:00:00.0: AGP aperture is 64M @ 0xf8000000
[ 13.819649] lp: driver loaded but no devices found
[ 13.928539] [drm] Initialized drm 1.1.0 20060810
[ 13.977937] parport_pc 00:09: reported by Plug and Play ACPI
[ 13.978089] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 14.049952] [drm] radeon defaulting to kernel modesetting.
[ 14.049959] [drm] radeon kernel modesetting enabled.
[ 14.050056] alloc irq_desc for 16 on node -1
[ 14.050061] alloc kstat_irqs on node -1
[ 14.050073] radeon 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 14.056439] [drm] radeon: Initializing kernel modesetting.
[ 14.057379] type=1505 audit(1344878139.193:2): operation="profile_load" pid=507 name="/sbin/dhclient3"
[ 14.058271] type=1505 audit(1344878139.193:3): operation="profile_load" pid=507 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 14.058755] type=1505 audit(1344878139.193:4): operation="profile_load" pid=507 name="/usr/lib/connman/scripts/dhclient-script"
[ 14.059046] ppdev: user-space parallel port driver
[ 14.059179] [drm] register mmio base: 0xFFDF0000
[ 14.059183] [drm] register mmio size: 65536
[ 14.060390] [drm] GPU reset succeed (RBBM_STATUS=0x00000140)
[ 14.060421] [drm] Generation 2 PCI interface, using max accessible memory
[ 14.060437] agpgart-via 0000:00:00.0: AGP 3.5 bridge
[ 14.060473] agpgart-via 0000:00:00.0: putting AGP V3 device into 8x mode
[ 14.060579] radeon 0000:01:00.0: putting AGP V3 device into 8x mode
[ 14.060594] [drm] radeon: VRAM 256M
[ 14.060600] [drm] radeon: VRAM from 0x00000000 to 0x0FFFFFFF
[ 14.060604] [drm] radeon: GTT 64M
[ 14.060608] [drm] radeon: GTT from 0xF8000000 to 0xFBFFFFFF
[ 14.060676] [drm] radeon: irq initialized.
[ 14.061191] [drm] Detected VRAM RAM=256M, BAR=256M
[ 14.061198] [drm] RAM width 128bits DDR
[ 14.061301] [TTM] Zone kernel: Available graphics memory: 254564 kiB.
[ 14.061332] [drm] radeon: 256M of VRAM memory ready
[ 14.061337] [drm] radeon: 64M of GTT memory ready.
[ 14.061590] [drm] radeon: 1 quad pipes, 1 Z pipes initialized.
[ 14.061609] [drm] radeon: cp idle (0x10000C03)
[ 14.061685] [drm] Loading R300 Microcode
[ 14.061695] platform radeon_cp.0: firmware: requesting radeon/R300_cp.bin
[ 14.062152] type=1505 audit(1344878139.197:5): operation="profile_replace" pid=525 name="/sbin/dhclient3"
[ 14.063130] type=1505 audit(1344878139.197:6): operation="profile_replace" pid=525 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 14.063686] type=1505 audit(1344878139.197:7): operation="profile_replace" pid=525 name="/usr/lib/connman/scripts/dhclient-script"
[ 14.085605] lp0: using parport0 (interrupt-driven).
[ 14.133634] [drm] radeon: ring at 0x00000000F8000000
[ 14.133667] [drm] ring test succeeded in 0 usecs
[ 14.157134] [drm] radeon: ib pool ready.
[ 14.157271] [drm] ib test succeeded in 0 usecs
[ 14.158441] [drm] Default TV standard: PAL
[ 14.158446] [drm] 27.000000000 MHz TV ref clk
[ 14.158452] [drm] DFP table revision: 4
[ 14.159312] [drm] Default TV standard: PAL
[ 14.159317] [drm] 27.000000000 MHz TV ref clk
[ 14.159539] [drm] Radeon Display Connectors
[ 14.159545] [drm] Connector 0:
[ 14.159548] [drm] VGA
[ 14.159553] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[ 14.159556] [drm] Encoders:
[ 14.159559] [drm] CRT1: INTERNAL_DAC1
[ 14.159562] [drm] Connector 1:
[ 14.159565] [drm] DVI-I
[ 14.159568] [drm] HPD1
[ 14.159572] [drm] DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[ 14.159576] [drm] Encoders:
[ 14.159580] [drm] CRT2: INTERNAL_DAC2
[ 14.159583] [drm] DFP1: INTERNAL_TMDS1
[ 14.159586] [drm] Connector 2:
[ 14.159588] [drm] S-video
[ 14.159591] [drm] Encoders:
[ 14.159594] [drm] TV1: INTERNAL_DAC2
[ 14.161288] rtusb init --->
[ 14.162155] === pAd = e0b08000, size = 471320 ===
[ 14.162160] <-- RTMPAllocAdapterBlock, Status=0
[ 14.166094] usbcore: registered new interface driver rt2870
[ 14.407569] alloc irq_desc for 22 on node -1
[ 14.407595] alloc kstat_irqs on node -1
[ 14.407642] VIA 82xx Audio 0000:00:11.5: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[ 14.407972] VIA 82xx Audio 0000:00:11.5: setting latency timer to 64
[ 14.408960] [drm] fb mappable at 0xE0040000
[ 14.408966] [drm] vram apper at 0xE0000000
[ 14.408969] [drm] size 5242880
[ 14.408973] [drm] fb depth is 24
[ 14.408976] [drm] pitch is 5120
[ 14.410337] fb0: radeondrmfb frame buffer device
[ 14.410344] registered panic notifier
[ 14.410361] [drm] Initialized radeon 2.0.0 20080528 for 0000:01:00.0 on minor 0
[ 14.417498] vga16fb: initializing
[ 14.417512] vga16fb: mapped to 0xc00a0000
[ 14.417522] vga16fb: not registering due to another framebuffer present
[ 14.517090] Console: switching to colour frame buffer device 160x64
[ 14.707404] type=1505 audit(1344878139.840:8): operation="profile_load" pid=662 name="/usr/share/gdm/guest-session/Xsession"
[ 14.712257] type=1505 audit(1344878139.848:9): operation="profile_replace" pid=663 name="/sbin/dhclient3"
[ 14.713249] type=1505 audit(1344878139.848:10): operation="profile_replace" pid=663 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 14.713794] type=1505 audit(1344878139.848:11): operation="profile_replace" pid=663 name="/usr/lib/connman/scripts/dhclient-script"
[ 14.882268] eth0: link down
[ 14.882427] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.898525] usb 1-4: firmware: requesting rt3070.bin
[ 15.285821] <-- RTMPAllocTxRxRingMemory, Status=0
[ 15.354670] -->RTUSBVenderReset
[ 15.355165] <--RTUSBVenderReset
[ 15.738702] 1. Phy Mode = 0
[ 15.738709] 2. Phy Mode = 0
[ 15.738714] NVM is Efuse and its size =2d[2d0-2fc]
[ 15.848361] 3. Phy Mode = 0
[ 15.850410] CPU0 attaching NULL sched-domain.
[ 15.850423] CPU1 attaching NULL sched-domain.
[ 15.854229] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 15.854235] MCS Set = 00 00 00 00 00
[ 15.873119] CPU0 attaching sched-domain:
[ 15.873128] domain 0: span 0-1 level SIBLING
[ 15.873134] groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[ 15.873146] domain 1: span 0-1 level MC
[ 15.873152] groups: 0-1 (cpu_power = 1178)
[ 15.873164] CPU1 attaching sched-domain:
[ 15.873168] domain 0: span 0-1 level SIBLING
[ 15.873173] groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[ 15.873185] domain 1: span 0-1 level MC
[ 15.873190] groups: 0-1 (cpu_power = 1178)
[ 15.924998] <==== rt28xx_init, Status=0
[ 15.926496] 0x1300 = 00073200
[ 15.930294] eth1: link down
[ 15.930395] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 18.481849] CPU0 attaching NULL sched-domain.
[ 18.481862] CPU1 attaching NULL sched-domain.
[ 18.509568] CPU0 attaching sched-domain:
[ 18.509577] domain 0: span 0-1 level SIBLING
[ 18.509583] groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[ 18.509594] domain 1: span 0-1 level MC
[ 18.509599] groups: 0-1 (cpu_power = 1178)
[ 18.509610] CPU1 attaching sched-domain:
[ 18.509614] domain 0: span 0-1 level SIBLING
[ 18.509620] groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[ 18.509631] domain 1: span 0-1 level MC
[ 18.509636] groups: 0-1 (cpu_power = 1178)
[ 21.049157] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 26.568017] wlan0: no IPv6 routers present
[ 41.605058] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 41.605612] ==>rt_ioctl_siwfreq::SIOCSIWFREQ[cmd=0x8b04] (Channel=1)
[ 70.870373] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 110.872055] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 112.164037] ata2.01: qc timeout (cmd 0xa0)
[ 112.164053] ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 112.164059] sr 1:0:1:0: CDB: Test Unit Ready: 00 00 00 00 00 00
[ 112.164075] ata2.01: cmd a0/00:00:00:00:00/00:00:00:00:00/b0 tag 0
[ 112.164076] res 51/20:03:00:00:00/00:00:00:00:00/b0 Emask 0x5 (timeout)
[ 112.164081] ata2.01: status: { DRDY ERR }
[ 112.164111] ata2: soft resetting link
[ 112.464277] ata2.01: configured for UDMA/66
[ 112.465625] ata2: EH complete
[ 122.884039] ata2.01: qc timeout (cmd 0xa0)
[ 122.884054] ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 122.884061] sr 1:0:1:0: CDB: Test Unit Ready: 00 00 00 00 00 00
[ 122.884077] ata2.01: cmd a0/00:00:00:00:00/00:00:00:00:00/b0 tag 0
[ 122.884078] res 51/20:03:00:00:00/00:00:00:00:00/b0 Emask 0x5 (timeout)
[ 122.884083] ata2.01: status: { DRDY ERR }
[ 122.884113] ata2: soft resetting link
[ 128.160042] ata2.01: qc timeout (cmd 0xa1)
[ 128.160053] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 128.160057] ata2.01: revalidation failed (errno=-5)
[ 133.200028] ata2: link is slow to respond, please be patient (ready=0)
[ 135.506829] DeQueueRunning[0]= TRUE!
[ 138.184032] ata2: device not ready (errno=-16), forcing hardreset
[ 138.184044] ata2: soft resetting link
[ 148.396041] ata2.01: qc timeout (cmd 0xa1)
[ 148.396051] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 148.396055] ata2.01: revalidation failed (errno=-5)
[ 153.436018] ata2: link is slow to respond, please be patient (ready=0)
[ 158.421021] ata2: device not ready (errno=-16), forcing hardreset
[ 158.421034] ata2: soft resetting link
[ 170.872053] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 188.633051] ata2.01: qc timeout (cmd 0xa1)
[ 188.633062] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 188.633067] ata2.01: revalidation failed (errno=-5)
[ 188.633072] ata2.01: disabled
[ 193.673023] ata2: link is slow to respond, please be patient (ready=0)
[ 198.656019] ata2: device not ready (errno=-16), forcing hardreset
[ 198.656032] ata2: soft resetting link
[ 198.823353] ata2: EH complete
[ 250.865559] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 301.868677] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 301.869025] ==>rt_ioctl_siwfreq::SIOCSIWFREQ[cmd=0x8b04] (Channel=1)
[ 350.873064] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 470.873940] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173


[Dimitrios.gr]

Ωραία , πάτα το πράσινο τικ , αλλά δώσε και τα αποτελέσματα του dmesg , να δούμε τα μηνύματα.

Κώδικας: Επιλογή όλων

[ 0.192078] pci 0000:00:00.0: reg 10 32bit mmio pref: [0xf8000000-0xfbffffff]
[ 0.192559] pci 0000:00:01.0: supports D1
[ 0.192616] pci 0000:00:09.0: reg 10 io port: [0xec00-0xecff]
[ 0.192627] pci 0000:00:09.0: reg 14 32bit mmio: [0xffefff00-0xffefffff]
[ 0.192660] pci 0000:00:09.0: reg 30 32bit mmio pref: [0xffec0000-0xffedffff]
[ 0.192698] pci 0000:00:09.0: supports D1 D2
[ 0.192703] pci 0000:00:09.0: PME# supported from D1 D2 D3hot
[ 0.192710] pci 0000:00:09.0: PME# disabled
[ 0.192787] pci 0000:00:0f.0: reg 20 io port: [0xfc00-0xfc0f]
[ 0.192898] pci 0000:00:10.0: reg 20 io port: [0xdc00-0xdc1f]
[ 0.192944] pci 0000:00:10.0: supports D1 D2
[ 0.192949] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.192956] pci 0000:00:10.0: PME# disabled
[ 0.193021] pci 0000:00:10.1: reg 20 io port: [0xe000-0xe01f]
[ 0.193068] pci 0000:00:10.1: supports D1 D2
[ 0.193072] pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.193079] pci 0000:00:10.1: PME# disabled
[ 0.193183] pci 0000:00:10.2: reg 20 io port: [0xe400-0xe41f]
[ 0.193230] pci 0000:00:10.2: supports D1 D2
[ 0.193235] pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.193242] pci 0000:00:10.2: PME# disabled
[ 0.193307] pci 0000:00:10.3: reg 20 io port: [0xe800-0xe81f]
[ 0.193354] pci 0000:00:10.3: supports D1 D2
[ 0.193359] pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.193366] pci 0000:00:10.3: PME# disabled
[ 0.193410] pci 0000:00:10.4: reg 10 32bit mmio: [0xffeffd00-0xffeffdff]
[ 0.193479] pci 0000:00:10.4: supports D1 D2
[ 0.193483] pci 0000:00:10.4: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.193490] pci 0000:00:10.4: PME# disabled
[ 0.193575] HPET not enabled in BIOS. You might try hpet=force boot option
[ 0.193688] pci 0000:00:11.5: reg 10 io port: [0xd800-0xd8ff]
[ 0.193785] pci 0000:00:11.5: supports D1 D2
[ 0.193835] pci 0000:00:12.0: reg 10 io port: [0xd400-0xd4ff]
[ 0.193846] pci 0000:00:12.0: reg 14 32bit mmio: [0xffeffc00-0xffeffcff]
[ 0.193910] pci 0000:00:12.0: supports D1 D2
[ 0.193914] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.193921] pci 0000:00:12.0: PME# disabled
[ 0.194003] pci 0000:01:00.0: reg 10 32bit mmio pref: [0xe0000000-0xefffffff]
[ 0.194014] pci 0000:01:00.0: reg 14 io port: [0xc800-0xc8ff]
[ 0.194024] pci 0000:01:00.0: reg 18 32bit mmio: [0xffdf0000-0xffdfffff]
[ 0.194048] pci 0000:01:00.0: reg 30 32bit mmio pref: [0xffdc0000-0xffddffff]
[ 0.194093] pci 0000:01:00.0: supports D1 D2
[ 0.194135] pci 0000:01:00.1: reg 10 32bit mmio pref: [0xd0000000-0xdfffffff]
[ 0.194145] pci 0000:01:00.1: reg 14 32bit mmio: [0xffde0000-0xffdeffff]
[ 0.194201] pci 0000:01:00.1: supports D1 D2
[ 0.194263] pci 0000:00:01.0: bridge io port: [0xc000-0xcfff]
[ 0.194270] pci 0000:00:01.0: bridge 32bit mmio: [0xffd00000-0xffdfffff]
[ 0.194278] pci 0000:00:01.0: bridge 32bit mmio pref: [0xb7f00000-0xf7efffff]
[ 0.194290] pci_bus 0000:00: on NUMA node 0
[ 0.194299] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.201274] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.201474] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.201640] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.201805] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 *12 14 15)
[ 0.201971] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.202172] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.202341] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.202510] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.202778] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.202786] vgaarb: loaded
[ 0.203040] SCSI subsystem initialized
[ 0.203331] libata version 3.00 loaded.
[ 0.203443] usbcore: registered new interface driver usbfs
[ 0.203470] usbcore: registered new interface driver hub
[ 0.203528] usbcore: registered new device driver usb
[ 0.203834] ACPI: WMI: Mapper loaded
[ 0.203840] PCI: Using ACPI for IRQ routing
[ 0.204166] NetLabel: Initializing
[ 0.204171] NetLabel: domain hash size = 128
[ 0.204174] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.204198] NetLabel: unlabeled traffic allowed by default
[ 0.204287] Switching to clocksource tsc
[ 0.208085] AppArmor: AppArmor Filesystem Enabled
[ 0.208118] pnp: PnP ACPI init
[ 0.208158] ACPI: bus type pnp registered
[ 0.212703] pnp: PnP ACPI: found 10 devices
[ 0.212717] ACPI: ACPI bus type pnp unregistered
[ 0.212727] PnPBIOS: Disabled by ACPI PNP
[ 0.212778] system 00:01: ioport range 0x290-0x297 has been reserved
[ 0.212785] system 00:01: ioport range 0x3f0-0x3f1 has been reserved
[ 0.212790] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 0.212796] system 00:01: ioport range 0x400-0x40f has been reserved
[ 0.212802] system 00:01: ioport range 0x820-0x821 has been reserved
[ 0.212809] system 00:01: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.247728] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.247736] pci 0000:00:01.0: IO window: 0xc000-0xcfff
[ 0.247745] pci 0000:00:01.0: MEM window: 0xffd00000-0xffdfffff
[ 0.247752] pci 0000:00:01.0: PREFETCH window: 0xb7f00000-0xf7efffff
[ 0.247777] pci 0000:00:01.0: setting latency timer to 64
[ 0.247785] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.247791] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.247796] pci_bus 0000:01: resource 0 io: [0xc000-0xcfff]
[ 0.247802] pci_bus 0000:01: resource 1 mem: [0xffd00000-0xffdfffff]
[ 0.247807] pci_bus 0000:01: resource 2 pref mem [0xb7f00000-0xf7efffff]
[ 0.247884] NET: Registered protocol family 2
[ 0.248079] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.248743] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.248886] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.249026] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.249031] TCP reno registered
[ 0.249171] NET: Registered protocol family 1
[ 0.249211] pci 0000:00:01.0: disabling DAC on VIA PCI bridge
[ 0.249245] alloc irq_desc for 21 on node -1
[ 0.249250] alloc kstat_irqs on node -1
[ 0.249263] pci 0000:00:10.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 0.249284] pci 0000:00:10.0: PCI INT A disabled
[ 0.249300] pci 0000:00:10.1: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 0.249320] pci 0000:00:10.1: PCI INT A disabled
[ 0.249336] pci 0000:00:10.2: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.249356] pci 0000:00:10.2: PCI INT B disabled
[ 0.249371] pci 0000:00:10.3: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.249391] pci 0000:00:10.3: PCI INT B disabled
[ 0.249407] pci 0000:00:10.4: PCI INT C -> GSI 21 (level, low) -> IRQ 21
[ 0.249445] pci 0000:00:10.4: PCI INT C disabled
[ 0.249454] pci 0000:00:11.0: Bypassing VIA 8237 APIC De-Assert Message
[ 0.249469] pci 0000:01:00.0: Boot video device
[ 0.249845] cpufreq-nforce2: No nForce2 chipset.
[ 0.249904] Scanning for low memory corruption every 60 seconds
[ 0.250141] audit: initializing netlink socket (disabled)
[ 0.250160] type=2000 audit(1344878124.247:1): initialized
[ 0.262737] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.266072] VFS: Disk quotas dquot_6.5.2
[ 0.266210] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.267636] fuse init (API version 7.13)
[ 0.267823] msgmni has been set to 977
[ 0.268341] alg: No test for stdrng (krng)
[ 0.268459] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.268466] io scheduler noop registered
[ 0.268470] io scheduler anticipatory registered
[ 0.268474] io scheduler deadline registered
[ 0.268567] io scheduler cfq registered (default)
[ 0.268846] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.268893] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.269108] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.269115] ACPI: Power Button [PWRB]
[ 0.269228] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.269234] ACPI: Power Button [PWRF]
[ 0.269640] processor LNXCPU:00: registered as cooling_device0
[ 0.269732] processor LNXCPU:01: registered as cooling_device1
[ 0.276329] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.276479] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.277114] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.279399] brd: module loaded
[ 0.279548] isapnp: Scanning for PnP cards...
[ 0.280370] loop: module loaded
[ 0.280531] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 0.280819] alloc irq_desc for 20 on node -1
[ 0.280823] alloc kstat_irqs on node -1
[ 0.280837] pata_acpi 0000:00:0f.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.280923] pata_acpi 0000:00:0f.0: PCI INT A disabled
[ 0.281485] Fixed MDIO Bus: probed
[ 0.281549] PPP generic driver version 2.4.2
[ 0.281611] tun: Universal TUN/TAP device driver, 1.6
[ 0.281615] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.281767] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.281794] ehci_hcd 0000:00:10.4: PCI INT C -> GSI 21 (level, low) -> IRQ 21
[ 0.281821] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 0.281892] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
[ 0.281987] ehci_hcd 0000:00:10.4: irq 21, io mem 0xffeffd00
[ 0.291760] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00
[ 0.291956] usb usb1: configuration #1 chosen from 1 choice
[ 0.292009] hub 1-0:1.0: USB hub found
[ 0.292029] hub 1-0:1.0: 8 ports detected
[ 0.292135] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.292165] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.292241] uhci_hcd 0000:00:10.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 0.292256] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 0.292325] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 0.292356] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000dc00
[ 0.292520] usb usb2: configuration #1 chosen from 1 choice
[ 0.292566] hub 2-0:1.0: USB hub found
[ 0.292583] hub 2-0:1.0: 2 ports detected
[ 0.292659] uhci_hcd 0000:00:10.1: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 0.292670] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 0.292733] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 0.292758] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000e000
[ 0.292921] usb usb3: configuration #1 chosen from 1 choice
[ 0.292967] hub 3-0:1.0: USB hub found
[ 0.292983] hub 3-0:1.0: 2 ports detected
[ 0.293063] uhci_hcd 0000:00:10.2: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.293074] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 0.293128] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[ 0.293154] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000e400
[ 0.293321] usb usb4: configuration #1 chosen from 1 choice
[ 0.293366] hub 4-0:1.0: USB hub found
[ 0.293381] hub 4-0:1.0: 2 ports detected
[ 0.293456] uhci_hcd 0000:00:10.3: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.293467] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 0.293520] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
[ 0.293546] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000e800
[ 0.293723] usb usb5: configuration #1 chosen from 1 choice
[ 0.293774] hub 5-0:1.0: USB hub found
[ 0.293790] hub 5-0:1.0: 2 ports detected
[ 0.293936] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 0.293941] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 0.294121] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.294315] mice: PS/2 mouse device common for all mice
[ 0.294504] rtc_cmos 00:03: RTC can wake from S4
[ 0.294579] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.294634] rtc0: alarms up to one year, y3k, 114 bytes nvram
[ 0.294843] device-mapper: uevent: version 1.0.3
[ 0.320119] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 0.329249] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.343915] device-mapper: multipath: version 1.1.0 loaded
[ 0.343922] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.344240] EISA: Probing bus 0 at eisa.0
[ 0.344288] EISA: Detected 0 cards.
[ 0.359671] cpuidle: using governor ladder
[ 0.359677] cpuidle: using governor menu
[ 0.360583] TCP cubic registered
[ 0.360853] NET: Registered protocol family 10
[ 0.362457] NET: Registered protocol family 17
[ 0.362559] Using IPI No-Shortcut mode
[ 0.362735] PM: Resume from disk failed.
[ 0.362760] registered taskstats version 1
[ 0.363171] Magic number: 8:511:289
[ 0.363227] tty tty22: hash matches
[ 0.363317] rtc_cmos 00:03: setting system clock to 2012-08-13 17:15:25 UTC (1344878125)
[ 0.363322] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.363325] EDD information not available.
[ 0.511527] Freeing initrd memory: 7838k freed
[ 0.634023] isapnp: No Plug & Play device found
[ 0.634058] Freeing unused kernel memory: 664k freed
[ 0.635366] Write protecting the kernel text: 4700k
[ 0.635422] Write protecting the kernel read-only data: 1848k
[ 0.662542] udev: starting version 151
[ 0.715641] usb 1-4: new high speed USB device using ehci_hcd and address 3
[ 0.854478] pata_via 0000:00:0f.0: version 0.3.4
[ 0.854531] pata_via 0000:00:0f.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.867564] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 0.867634] scsi0 : pata_via
[ 0.868049] scsi1 : pata_via
[ 0.872039] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
[ 0.872046] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
[ 0.872319] alloc irq_desc for 23 on node -1
[ 0.872324] alloc kstat_irqs on node -1
[ 0.872337] via-rhine 0000:00:12.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.873784] eth0: VIA Rhine II at 0xffeffc00, 00:11:09:84:6f:3e, IRQ 23.
[ 0.874493] eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
[ 0.874976] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 0.875048] 8139cp 0000:00:09.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 0.875141] Floppy drive(s): fd0 is 1.44M
[ 0.876328] usb 1-4: configuration #1 chosen from 1 choice
[ 0.891591] FDC 0 is a post-1991 82077
[ 1.044248] ata1.01: ATA-7: Maxtor 6Y080P0, YAR41BW0, max UDMA/133
[ 1.044253] ata1.01: 160086528 sectors, multi 16: LBA
[ 1.044288] ata1.01: limited to UDMA/33 due to 40-wire cable
[ 1.060130] ata1.01: configured for UDMA/33
[ 1.060310] scsi 0:0:1:0: Direct-Access ATA Maxtor 6Y080P0 YAR4 PQ: 0 ANSI: 5
[ 1.060633] sd 0:0:1:0: Attached scsi generic sg0 type 0
[ 1.060812] sd 0:0:1:0: [sda] 160086528 512-byte logical blocks: (81.9 GB/76.3 GiB)
[ 1.060913] sd 0:0:1:0: [sda] Write Protect is off
[ 1.060918] sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
[ 1.060955] sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.061157] sda: sda1 sda2 < sda5 >
[ 1.085878] sd 0:0:1:0: [sda] Attached SCSI disk
[ 1.119602] usb 2-2: new full speed USB device using uhci_hcd and address 2
[ 1.296650] usb 2-2: configuration #1 chosen from 1 choice
[ 1.345377] ata2.01: ATAPI: SONY DVD RW DW-D22A, BYS1, max UDMA/66
[ 1.360269] ata2.01: configured for UDMA/66
[ 1.361629] scsi 1:0:1:0: CD-ROM SONY DVD RW DW-D22A BYS1 PQ: 0 ANSI: 5
[ 1.365741] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 1.365746] Uniform CD-ROM driver Revision: 3.20
[ 1.365933] sr 1:0:1:0: Attached scsi CD-ROM sr0
[ 1.366070] sr 1:0:1:0: Attached scsi generic sg1 type 5
[ 1.372939] 8139too Fast Ethernet driver 0.9.28
[ 1.373049] alloc irq_desc for 17 on node -1
[ 1.373055] alloc kstat_irqs on node -1
[ 1.373070] 8139too 0000:00:09.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.375171] eth1: RealTek RTL8139 at 0xec00, f8:d1:11:04:c3:f4, IRQ 17
[ 1.384378] usbcore: registered new interface driver hiddev
[ 1.394764] input: Microsoft SideWinder™ Mouse as /devices/pci0000:00/0000:00:10.0/usb2/2-2/2-2:1.0/input/input4
[ 1.395003] generic-usb 0003:045E:0724.0001: input,hidraw0: USB HID v1.11 Mouse [Microsoft SideWinder™ Mouse] on usb-0000:00:10.0-2/input0
[ 1.395057] usbcore: registered new interface driver usbhid
[ 1.395064] usbhid: v2.6:USB HID core driver
[ 1.628359] ext4-fs (sda5): mounted filesystem with ordered data mode
[ 13.369031] Adding 2928632k swap on /dev/sda1. Priority:-1 extents:1 across:2928632k
[ 13.410681] udev: starting version 151
[ 13.599256] udev: renamed network interface eth0 to eth1
[ 13.622738] udev: renamed network interface eth1_rename to eth0
[ 13.647641] ACPI: resource vt596_smbus [0x400-0x407] conflicts with ACPI region SMOV [0x400-0x406]
[ 13.647648] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 13.656206] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 13.657273] Linux agpgart interface v0.103
[ 13.773491] agpgart: Detected VIA PT880 chipset
[ 13.812431] agpgart-via 0000:00:00.0: AGP aperture is 64M @ 0xf8000000
[ 13.819649] lp: driver loaded but no devices found
[ 13.928539] [drm] Initialized drm 1.1.0 20060810
[ 13.977937] parport_pc 00:09: reported by Plug and Play ACPI
[ 13.978089] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 14.049952] [drm] radeon defaulting to kernel modesetting.
[ 14.049959] [drm] radeon kernel modesetting enabled.
[ 14.050056] alloc irq_desc for 16 on node -1
[ 14.050061] alloc kstat_irqs on node -1
[ 14.050073] radeon 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 14.056439] [drm] radeon: Initializing kernel modesetting.
[ 14.057379] type=1505 audit(1344878139.193:2): operation="profile_load" pid=507 name="/sbin/dhclient3"
[ 14.058271] type=1505 audit(1344878139.193:3): operation="profile_load" pid=507 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 14.058755] type=1505 audit(1344878139.193:4): operation="profile_load" pid=507 name="/usr/lib/connman/scripts/dhclient-script"
[ 14.059046] ppdev: user-space parallel port driver
[ 14.059179] [drm] register mmio base: 0xFFDF0000
[ 14.059183] [drm] register mmio size: 65536
[ 14.060390] [drm] GPU reset succeed (RBBM_STATUS=0x00000140)
[ 14.060421] [drm] Generation 2 PCI interface, using max accessible memory
[ 14.060437] agpgart-via 0000:00:00.0: AGP 3.5 bridge
[ 14.060473] agpgart-via 0000:00:00.0: putting AGP V3 device into 8x mode
[ 14.060579] radeon 0000:01:00.0: putting AGP V3 device into 8x mode
[ 14.060594] [drm] radeon: VRAM 256M
[ 14.060600] [drm] radeon: VRAM from 0x00000000 to 0x0FFFFFFF
[ 14.060604] [drm] radeon: GTT 64M
[ 14.060608] [drm] radeon: GTT from 0xF8000000 to 0xFBFFFFFF
[ 14.060676] [drm] radeon: irq initialized.
[ 14.061191] [drm] Detected VRAM RAM=256M, BAR=256M
[ 14.061198] [drm] RAM width 128bits DDR
[ 14.061301] [TTM] Zone kernel: Available graphics memory: 254564 kiB.
[ 14.061332] [drm] radeon: 256M of VRAM memory ready
[ 14.061337] [drm] radeon: 64M of GTT memory ready.
[ 14.061590] [drm] radeon: 1 quad pipes, 1 Z pipes initialized.
[ 14.061609] [drm] radeon: cp idle (0x10000C03)
[ 14.061685] [drm] Loading R300 Microcode
[ 14.061695] platform radeon_cp.0: firmware: requesting radeon/R300_cp.bin
[ 14.062152] type=1505 audit(1344878139.197:5): operation="profile_replace" pid=525 name="/sbin/dhclient3"
[ 14.063130] type=1505 audit(1344878139.197:6): operation="profile_replace" pid=525 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 14.063686] type=1505 audit(1344878139.197:7): operation="profile_replace" pid=525 name="/usr/lib/connman/scripts/dhclient-script"
[ 14.085605] lp0: using parport0 (interrupt-driven).
[ 14.133634] [drm] radeon: ring at 0x00000000F8000000
[ 14.133667] [drm] ring test succeeded in 0 usecs
[ 14.157134] [drm] radeon: ib pool ready.
[ 14.157271] [drm] ib test succeeded in 0 usecs
[ 14.158441] [drm] Default TV standard: PAL
[ 14.158446] [drm] 27.000000000 MHz TV ref clk
[ 14.158452] [drm] DFP table revision: 4
[ 14.159312] [drm] Default TV standard: PAL
[ 14.159317] [drm] 27.000000000 MHz TV ref clk
[ 14.159539] [drm] Radeon Display Connectors
[ 14.159545] [drm] Connector 0:
[ 14.159548] [drm] VGA
[ 14.159553] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[ 14.159556] [drm] Encoders:
[ 14.159559] [drm] CRT1: INTERNAL_DAC1
[ 14.159562] [drm] Connector 1:
[ 14.159565] [drm] DVI-I
[ 14.159568] [drm] HPD1
[ 14.159572] [drm] DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[ 14.159576] [drm] Encoders:
[ 14.159580] [drm] CRT2: INTERNAL_DAC2
[ 14.159583] [drm] DFP1: INTERNAL_TMDS1
[ 14.159586] [drm] Connector 2:
[ 14.159588] [drm] S-video
[ 14.159591] [drm] Encoders:
[ 14.159594] [drm] TV1: INTERNAL_DAC2
[ 14.161288] rtusb init --->
[ 14.162155] === pAd = e0b08000, size = 471320 ===
[ 14.162160] <-- RTMPAllocAdapterBlock, Status=0
[ 14.166094] usbcore: registered new interface driver rt2870
[ 14.407569] alloc irq_desc for 22 on node -1
[ 14.407595] alloc kstat_irqs on node -1
[ 14.407642] VIA 82xx Audio 0000:00:11.5: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[ 14.407972] VIA 82xx Audio 0000:00:11.5: setting latency timer to 64
[ 14.408960] [drm] fb mappable at 0xE0040000
[ 14.408966] [drm] vram apper at 0xE0000000
[ 14.408969] [drm] size 5242880
[ 14.408973] [drm] fb depth is 24
[ 14.408976] [drm] pitch is 5120
[ 14.410337] fb0: radeondrmfb frame buffer device
[ 14.410344] registered panic notifier
[ 14.410361] [drm] Initialized radeon 2.0.0 20080528 for 0000:01:00.0 on minor 0
[ 14.417498] vga16fb: initializing
[ 14.417512] vga16fb: mapped to 0xc00a0000
[ 14.417522] vga16fb: not registering due to another framebuffer present
[ 14.517090] Console: switching to colour frame buffer device 160x64
[ 14.707404] type=1505 audit(1344878139.840:8): operation="profile_load" pid=662 name="/usr/share/gdm/guest-session/Xsession"
[ 14.712257] type=1505 audit(1344878139.848:9): operation="profile_replace" pid=663 name="/sbin/dhclient3"
[ 14.713249] type=1505 audit(1344878139.848:10): operation="profile_replace" pid=663 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 14.713794] type=1505 audit(1344878139.848:11): operation="profile_replace" pid=663 name="/usr/lib/connman/scripts/dhclient-script"
[ 14.882268] eth0: link down
[ 14.882427] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.898525] usb 1-4: firmware: requesting rt3070.bin
[ 15.285821] <-- RTMPAllocTxRxRingMemory, Status=0
[ 15.354670] -->RTUSBVenderReset
[ 15.355165] <--RTUSBVenderReset
[ 15.738702] 1. Phy Mode = 0
[ 15.738709] 2. Phy Mode = 0
[ 15.738714] NVM is Efuse and its size =2d[2d0-2fc]
[ 15.848361] 3. Phy Mode = 0
[ 15.850410] CPU0 attaching NULL sched-domain.
[ 15.850423] CPU1 attaching NULL sched-domain.
[ 15.854229] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 15.854235] MCS Set = 00 00 00 00 00
[ 15.873119] CPU0 attaching sched-domain:
[ 15.873128] domain 0: span 0-1 level SIBLING
[ 15.873134] groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[ 15.873146] domain 1: span 0-1 level MC
[ 15.873152] groups: 0-1 (cpu_power = 1178)
[ 15.873164] CPU1 attaching sched-domain:
[ 15.873168] domain 0: span 0-1 level SIBLING
[ 15.873173] groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[ 15.873185] domain 1: span 0-1 level MC
[ 15.873190] groups: 0-1 (cpu_power = 1178)
[ 15.924998] <==== rt28xx_init, Status=0
[ 15.926496] 0x1300 = 00073200
[ 15.930294] eth1: link down
[ 15.930395] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 18.481849] CPU0 attaching NULL sched-domain.
[ 18.481862] CPU1 attaching NULL sched-domain.
[ 18.509568] CPU0 attaching sched-domain:
[ 18.509577] domain 0: span 0-1 level SIBLING
[ 18.509583] groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[ 18.509594] domain 1: span 0-1 level MC
[ 18.509599] groups: 0-1 (cpu_power = 1178)
[ 18.509610] CPU1 attaching sched-domain:
[ 18.509614] domain 0: span 0-1 level SIBLING
[ 18.509620] groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[ 18.509631] domain 1: span 0-1 level MC
[ 18.509636] groups: 0-1 (cpu_power = 1178)
[ 21.049157] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 26.568017] wlan0: no IPv6 routers present
[ 41.605058] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 41.605612] ==>rt_ioctl_siwfreq::SIOCSIWFREQ[cmd=0x8b04] (Channel=1)
[ 70.870373] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 110.872055] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 112.164037] ata2.01: qc timeout (cmd 0xa0)
[ 112.164053] ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 112.164059] sr 1:0:1:0: CDB: Test Unit Ready: 00 00 00 00 00 00
[ 112.164075] ata2.01: cmd a0/00:00:00:00:00/00:00:00:00:00/b0 tag 0
[ 112.164076] res 51/20:03:00:00:00/00:00:00:00:00/b0 Emask 0x5 (timeout)
[ 112.164081] ata2.01: status: { DRDY ERR }
[ 112.164111] ata2: soft resetting link
[ 112.464277] ata2.01: configured for UDMA/66
[ 112.465625] ata2: EH complete
[ 122.884039] ata2.01: qc timeout (cmd 0xa0)
[ 122.884054] ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 122.884061] sr 1:0:1:0: CDB: Test Unit Ready: 00 00 00 00 00 00
[ 122.884077] ata2.01: cmd a0/00:00:00:00:00/00:00:00:00:00/b0 tag 0
[ 122.884078] res 51/20:03:00:00:00/00:00:00:00:00/b0 Emask 0x5 (timeout)
[ 122.884083] ata2.01: status: { DRDY ERR }
[ 122.884113] ata2: soft resetting link
[ 128.160042] ata2.01: qc timeout (cmd 0xa1)
[ 128.160053] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 128.160057] ata2.01: revalidation failed (errno=-5)
[ 133.200028] ata2: link is slow to respond, please be patient (ready=0)
[ 135.506829] DeQueueRunning[0]= TRUE!
[ 138.184032] ata2: device not ready (errno=-16), forcing hardreset
[ 138.184044] ata2: soft resetting link
[ 148.396041] ata2.01: qc timeout (cmd 0xa1)
[ 148.396051] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 148.396055] ata2.01: revalidation failed (errno=-5)
[ 153.436018] ata2: link is slow to respond, please be patient (ready=0)
[ 158.421021] ata2: device not ready (errno=-16), forcing hardreset
[ 158.421034] ata2: soft resetting link
[ 170.872053] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 188.633051] ata2.01: qc timeout (cmd 0xa1)
[ 188.633062] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 188.633067] ata2.01: revalidation failed (errno=-5)
[ 188.633072] ata2.01: disabled
[ 193.673023] ata2: link is slow to respond, please be patient (ready=0)
[ 198.656019] ata2: device not ready (errno=-16), forcing hardreset
[ 198.656032] ata2: soft resetting link
[ 198.823353] ata2: EH complete
[ 250.865559] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 301.868677] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 301.869025] ==>rt_ioctl_siwfreq::SIOCSIWFREQ[cmd=0x8b04] (Channel=1)
[ 350.873064] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173
[ 470.873940] ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 173


ολά καλά???

[Learner]

Και την

Κώδικας: Επιλογή όλων

iwconfig

αν θες.

[Dimitrios.gr]

Διορθώθηκε το επιπεδο θορύβου και το σήμα ή κάνω λάθος ???

Κώδικας: Επιλογή όλων

wlan0 Ralink STA ESSID:"Buggati" Nickname:"RT2870STA"
Mode:Managed Frequency=2.412 GHz Access Point: E8:39:DF:F2:9C:DB
Bit Rate=54 Mb/s
RTS thr:off Fragment thr:off
Link Quality=100/100 Signal level:-49 dBm Noise level:-83 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0


[Learner]

Ναι ,
επίσης έχει εξαφανιστεί και το μήνυμα

Κώδικας: Επιλογή όλων

rt2870sta: module is from the staging directory, the quality is unknown, you have been warned.

Ok , τέλος καλό όλα καλά.

[Dimitrios.gr]

Ναι ,
επίσης έχει εξαφανιστεί και το μήνυμα

Κώδικας: Επιλογή όλων

rt2870sta: module is from the staging directory, the quality is unknown, you have been warned.

Ok , τέλος καλό όλα καλά.

Ευχαριστω