Αστάθεια σε wireless συνδεση με το ubuntu 11.04

[Mark on Moon]

το λαπτοπ της υπογραφης μου παρουσιαζει ασταθεια με το wi-fi. Ειμαι συνδεδεμενος με το κινητο μου με την σύνδεση κανονικα κ το λαπτοπ πότε συνδεεται κ ποτε οχι.την συνδεση τη βλεπει συνεχεια κ οποτε δεν συνδεεται πεταει συνέχεια το εικονιδιο για εισαγωγη κωδικου χωρις κανενα αποτελεσμα. Το λαπτοπ δεν εχει προβλημα με ενσυρματη συνδεση , αλλα προτιμω χωρις καλώδιο. Ακομη να αναφερω οτι παρουσιαζει προβλημα με το παροχο της συνδεσης , αλλα δεν ειναι αυτο το προβλημα. Επιση να με συγχωρειτε για τονους κτλπ , γραφω απο το κινητο μου συνδεδεμενο με την wifi. Ευχαριστω

[logari81]

8086:4232

Δώσε μας το αποτέλεσμα της εντολής

Κώδικας: Επιλογή όλων

dmesg

Spoiler: show

http://forum.ubuntu-gr.org/viewtopic.php?f=39&t=11103&hilit=8086%3A4232&start=10#p113246

[Mark on Moon]

Κώδικας: Επιλογή όλων

[ 0.463026] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0
[ 0.464072] ACPI: Lid Switch [LID0]
[ 0.464119] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1
[ 0.464124] ACPI: Sleep Button [SLPB]
[ 0.464171] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 0.464175] ACPI: Power Button [PWRF]
[ 0.464214] ACPI: acpi_idle registered with cpuidle
[ 0.464648] Monitor-Mwait will be used to enter C-1 state
[ 0.464681] Monitor-Mwait will be used to enter C-2 state
[ 0.464687] Marking TSC unstable due to TSC halts in idle
[ 0.477831] Freeing initrd memory: 12880k freed
[ 0.485629] thermal LNXTHERM:00: registered as thermal_zone0
[ 0.485633] ACPI: Thermal Zone [TZS0] (37 C)
[ 0.490603] thermal LNXTHERM:01: registered as thermal_zone1
[ 0.490606] ACPI: Thermal Zone [TZS1] (37 C)
[ 0.490638] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 0.490675] ERST: Table is not found!
[ 0.490801] isapnp: Scanning for PnP cards...
[ 0.490820] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 0.626163] ACPI: Battery Slot [BAT0] (battery present)
[ 0.845110] isapnp: No Plug & Play device found
[ 0.853610] Linux agpgart interface v0.103
[ 0.855145] brd: module loaded
[ 0.855806] loop: module loaded
[ 0.856389] Fixed MDIO Bus: probed
[ 0.856417] PPP generic driver version 2.4.2
[ 0.856454] tun: Universal TUN/TAP device driver, 1.6
[ 0.856456] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.856548] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.856578] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 20 (level, low) -> IRQ 20
[ 0.856591] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 0.856596] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 0.856634] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 0.856667] ehci_hcd 0000:00:1a.7: debug port 1
[ 0.860550] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
[ 0.860568] ehci_hcd 0000:00:1a.7: irq 20, io mem 0xf3404800
[ 0.876017] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 0.876146] hub 1-0:1.0: USB hub found
[ 0.876150] hub 1-0:1.0: 4 ports detected
[ 0.876232] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.876245] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.876249] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.876289] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 0.876317] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.880201] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[ 0.880217] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf3404c00
[ 0.896018] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.896150] hub 2-0:1.0: USB hub found
[ 0.896154] hub 2-0:1.0: 8 ports detected
[ 0.896243] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.896259] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.896279] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.896286] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 0.896290] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 0.896326] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 0.896355] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001800
[ 0.896485] hub 3-0:1.0: USB hub found
[ 0.896490] hub 3-0:1.0: 2 ports detected
[ 0.896562] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 20 (level, low) -> IRQ 20
[ 0.896570] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 0.896573] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 0.896609] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 0.896638] uhci_hcd 0000:00:1a.1: irq 20, io base 0x00001820
[ 0.896767] hub 4-0:1.0: USB hub found
[ 0.896771] hub 4-0:1.0: 2 ports detected
[ 0.896844] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.896853] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.896857] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.896894] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 0.896923] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840
[ 0.897055] hub 5-0:1.0: USB hub found
[ 0.897059] hub 5-0:1.0: 2 ports detected
[ 0.897136] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.897143] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.897147] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.897182] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 0.897222] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00001860
[ 0.897349] hub 6-0:1.0: USB hub found
[ 0.897354] hub 6-0:1.0: 2 ports detected
[ 0.897425] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.897432] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.897436] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.897475] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 0.897515] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001880
[ 0.897642] hub 7-0:1.0: USB hub found
[ 0.897647] hub 7-0:1.0: 2 ports detected
[ 0.897714] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 18 (level, low) -> IRQ 18
[ 0.897721] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 0.897725] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 0.897764] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 8
[ 0.897792] uhci_hcd 0000:00:1d.3: irq 18, io base 0x000018a0
[ 0.897920] hub 8-0:1.0: USB hub found
[ 0.897924] hub 8-0:1.0: 2 ports detected
[ 0.898060] i8042: PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.913692] i8042: Detected active multiplexing controller, rev 1.1
[ 0.925945] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.925953] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.925986] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.926013] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.926040] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.926154] mousedev: PS/2 mouse device common for all mice
[ 0.926733] rtc_cmos 00:08: RTC can wake from S4
[ 0.926849] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[ 0.926881] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 0.926962] device-mapper: uevent: version 1.0.3
[ 0.927040] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[ 0.927128] device-mapper: multipath: version 1.3.0 loaded
[ 0.927130] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.927234] EISA: Probing bus 0 at eisa.0
[ 0.927236] EISA: Cannot allocate resource for mainboard
[ 0.927239] Cannot allocate resource for EISA slot 1
[ 0.927241] Cannot allocate resource for EISA slot 2
[ 0.927243] Cannot allocate resource for EISA slot 3
[ 0.927245] Cannot allocate resource for EISA slot 4
[ 0.927247] Cannot allocate resource for EISA slot 5
[ 0.927249] Cannot allocate resource for EISA slot 6
[ 0.927251] Cannot allocate resource for EISA slot 7
[ 0.927253] Cannot allocate resource for EISA slot 8
[ 0.927255] EISA: Detected 0 cards.
[ 0.927265] cpufreq-nforce2: No nForce2 chipset.
[ 0.927321] cpuidle: using governor ladder
[ 0.927404] cpuidle: using governor menu
[ 0.927407] EFI Variables Facility v0.08 2004-May-17
[ 0.927744] TCP cubic registered
[ 0.927902] NET: Registered protocol family 10
[ 0.928593] NET: Registered protocol family 17
[ 0.928607] Registering the dns_resolver key type
[ 0.928637] Using IPI No-Shortcut mode
[ 0.928726] PM: Hibernation image not present or could not be loaded.
[ 0.928738] registered taskstats version 1
[ 0.935920] Magic number: 7:249:935
[ 0.936031] rtc_cmos 00:08: setting system clock to 2011-08-29 11:56:21 UTC (1314618981)
[ 0.936657] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.936659] EDD information not available.
[ 0.936844] Freeing unused kernel memory: 716k freed
[ 0.937124] Write protecting the kernel text: 5452k
[ 0.937204] Write protecting the kernel read-only data: 2196k
[ 0.937206] NX-protecting the kernel data: 4788k
[ 0.952377] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 0.959175] udev[63]: starting version 167
[ 1.114999] tg3.c:v3.119 (May 18, 2011)
[ 1.115170] tg3 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.115181] tg3 0000:02:00.0: setting latency timer to 64
[ 1.122997] ahci 0000:00:1f.2: version 3.0
[ 1.123023] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.123557] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X
[ 1.123613] ahci: SSS flag set, parallel bus scan disabled
[ 1.123659] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
[ 1.123663] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ccc ems
[ 1.123670] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.148939] scsi0 : ahci
[ 1.149099] scsi1 : ahci
[ 1.149211] scsi2 : ahci
[ 1.149318] scsi3 : ahci
[ 1.149429] scsi4 : ahci
[ 1.149538] scsi5 : ahci
[ 1.149606] ata1: SATA max UDMA/133 abar m2048@0xf3404000 port 0xf3404100 irq 45
[ 1.149610] ata2: SATA max UDMA/133 abar m2048@0xf3404000 port 0xf3404180 irq 45
[ 1.149612] ata3: DUMMY
[ 1.149614] ata4: DUMMY
[ 1.149623] ata5: SATA max UDMA/133 abar m2048@0xf3404000 port 0xf3404300 irq 45
[ 1.149627] ata6: SATA max UDMA/133 abar m2048@0xf3404000 port 0xf3404380 irq 45
[ 1.176981] tg3 0000:02:00.0: eth0: Tigon3 [partno(BCM95784M) rev 5784100] (PCI Express) MAC address 00:1d:72:fd:f6:12
[ 1.176986] tg3 0000:02:00.0: eth0: attached PHY is 5784 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[ 1.176990] tg3 0000:02:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 1.176993] tg3 0000:02:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 1.264108] usb 2-5: new high speed USB device number 3 using ehci_hcd
[ 1.468071] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.521283] ata1.00: ATA-8: ST9250315AS, 0001SDM1, max UDMA/133
[ 1.521289] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.523414] ata1.00: configured for UDMA/133
[ 1.523636] scsi 0:0:0:0: Direct-Access ATA ST9250315AS 0001 PQ: 0 ANSI: 5
[ 1.523817] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.523843] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 1.523899] sd 0:0:0:0: [sda] Write Protect is off
[ 1.523903] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.523927] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.572720] sda: sda1 sda2 < sda5 >
[ 1.573156] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.676128] usb 5-1: new low speed USB device number 2 using uhci_hcd
[ 1.840071] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.853740] ata2.00: ATAPI: TSSTcorp CDDVDW TS-L633B, AC01, max UDMA/100
[ 1.853746] ata2.00: applying bridge limits
[ 1.867088] ata2.00: configured for UDMA/100
[ 1.869809] scsi 1:0:0:0: CD-ROM TSSTcorp CDDVDW TS-L633B AC01 PQ: 0 ANSI: 5
[ 1.875534] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.875539] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.875721] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.875791] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 2.192111] ata5: SATA link down (SStatus 0 SControl 300)
[ 2.512137] ata6: SATA link down (SStatus 0 SControl 300)
[ 2.528669] input: PIXART USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.0/input/input4
[ 2.528798] generic-usb 0003:093A:2510.0001: input,hidraw0: USB HID v1.10 Mouse [PIXART USB OPTICAL MOUSE] on usb-0000:00:1d.0-1/input0
[ 2.528818] usbcore: registered new interface driver usbhid
[ 2.528820] usbhid: USB HID core driver
[ 2.938940] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 18.155405] udev[267]: starting version 167
[ 18.250176] Adding 4187132k swap on /dev/sda5. Priority:-1 extents:1 across:4187132k
[ 18.333610] type=1400 audit(1314618998.894:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=381 comm="apparmor_parser"
[ 18.334568] type=1400 audit(1314618998.894:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=381 comm="apparmor_parser"
[ 18.335173] type=1400 audit(1314618998.894:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=381 comm="apparmor_parser"
[ 18.663636] wmi: Mapper loaded
[ 18.848952] acpi device:03: registered as cooling_device2
[ 18.849132] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input5
[ 18.849278] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 18.894833] Linux video capture interface: v2.00
[ 18.969668] uvcvideo: Found UVC 1.00 device CNF7017 (04f2:b044)
[ 19.025584] input: CNF7017 as /devices/pci0000:00/0000:00:1d.7/usb2/2-5/2-5:1.0/input/input6
[ 19.025778] usbcore: registered new interface driver uvcvideo
[ 19.025780] USB Video Class driver (v1.1.0)
[ 19.148825] acer_wmi: Acer Laptop ACPI-WMI Extras
[ 19.162500] acer_wmi: Brightness must be controlled by generic video driver
[ 19.186016] cfg80211: Calling CRDA to update world regulatory domain
[ 19.191460] cfg80211: World regulatory domain updated:
[ 19.191463] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 19.191467] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.191470] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 19.191473] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 19.191476] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.191479] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.277896] lp: driver loaded but no devices found
[ 19.472990] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:
[ 19.472994] iwlagn: Copyright(c) 2003-2011 Intel Corporation
[ 19.473061] iwlagn 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 19.473071] iwlagn 0000:04:00.0: setting latency timer to 64
[ 19.473101] iwlagn 0000:04:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54
[ 19.475595] [drm] Initialized drm 1.1.0 20060810
[ 19.495013] iwlagn 0000:04:00.0: device EEPROM VER=0x11f, CALIB=0x4
[ 19.495016] iwlagn 0000:04:00.0: Device SKU: 0Xb
[ 19.495029] iwlagn 0000:04:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels
[ 19.495259] iwlagn 0000:04:00.0: irq 46 for MSI/MSI-X
[ 19.580312] iwlagn 0000:04:00.0: loaded firmware version 8.83.5.1 build 33692
[ 19.580592] Registered led device: phy0-led
[ 19.580627] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[ 19.720622] nouveau 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 19.720631] nouveau 0000:01:00.0: setting latency timer to 64
[ 19.723769] [drm] nouveau 0000:01:00.0: Detected an NV50 generation card (0x298600a2)
[ 19.734402] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from PRAMIN
[ 19.828021] [drm] nouveau 0000:01:00.0: ... appears to be valid
[ 19.828026] [drm] nouveau 0000:01:00.0: BIT BIOS found
[ 19.828029] [drm] nouveau 0000:01:00.0: Bios version 62.98.5a.00
[ 19.828033] [drm] nouveau 0000:01:00.0: TMDS table version 2.0
[ 19.828036] [drm] nouveau 0000:01:00.0: Found Display Configuration Block version 4.0
[ 19.828040] [drm] nouveau 0000:01:00.0: Raw DCB entry 0: 01000323 00010034
[ 19.828043] [drm] nouveau 0000:01:00.0: Raw DCB entry 1: 02011300 00000028
[ 19.828046] [drm] nouveau 0000:01:00.0: Raw DCB entry 2: 02022312 00020010
[ 19.828049] [drm] nouveau 0000:01:00.0: Raw DCB entry 3: 0000000e 00000000
[ 19.828053] [drm] nouveau 0000:01:00.0: DCB connector table: VHER 0x40 5 16 4
[ 19.828056] [drm] nouveau 0000:01:00.0: 0: 0x00000040: type 0x40 idx 0 tag 0xff
[ 19.828060] [drm] nouveau 0000:01:00.0: 1: 0x00000100: type 0x00 idx 1 tag 0xff
[ 19.828063] [drm] nouveau 0000:01:00.0: 2: 0x00001261: type 0x61 idx 2 tag 0x07
[ 19.828066] [drm] nouveau 0000:01:00.0: 7: 0x00000513: type 0x13 idx 7 tag 0xff
[ 19.828071] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xDAD1
[ 19.853236] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xDEC9
[ 19.859547] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xE78C
[ 19.859556] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xE85A
[ 19.860641] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xEB10
[ 19.860644] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xEB75
[ 19.880490] [drm] nouveau 0000:01:00.0: 0xEB75: Condition still not met after 20ms, skipping following opcodes
[ 19.899922] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
[ 19.900717] [drm] nouveau 0000:01:00.0: 4 available performance level(s)
[ 19.900723] [drm] nouveau 0000:01:00.0: 0: memory 100MHz core 169MHz shader 338MHz voltage 900mV fanspeed 100% timing 4
[ 19.900728] [drm] nouveau 0000:01:00.0: 1: memory 250MHz core 275MHz shader 550MHz voltage 900mV fanspeed 100% timing 5
[ 19.900733] [drm] nouveau 0000:01:00.0: 2: memory 400MHz core 500MHz shader 1000MHz voltage 1090mV fanspeed 100% timing 6
[ 19.900738] [drm] nouveau 0000:01:00.0: 3: memory 500MHz core 640MHz shader 1600MHz voltage 1200mV fanspeed 100% timing 7
[ 19.900764] [drm] nouveau 0000:01:00.0: c: memory 249MHz core 275MHz shader 550MHz voltage 900mV
[ 19.900848] [TTM] Zone kernel: Available graphics memory: 420744 kiB.
[ 19.900850] [TTM] Zone highmem: Available graphics memory: 2058752 kiB.
[ 19.900853] [TTM] Initializing pool allocator.
[ 19.900869] [drm] nouveau 0000:01:00.0: Detected 512MiB VRAM
[ 19.906319] [drm] nouveau 0000:01:00.0: 512 MiB GART (aperture)
[ 19.943086] [drm] nouveau 0000:01:00.0: ACPI backlight interface available, not registering our own
[ 19.944511] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 19.944514] [drm] No driver support for vblank timestamp query.
[ 20.097345] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 20.123637] [drm] nouveau 0000:01:00.0: allocated 1366x768 fb: 0x40000000, bo ee877000
[ 20.123707] fbcon: nouveaufb (fb0) is primary device
[ 20.123799] Console: switching to colour frame buffer device 170x48
[ 20.123831] fb0: nouveaufb frame buffer device
[ 20.123833] drm: registered panic notifier
[ 20.123841] [drm] Initialized nouveau 0.0.16 20090420 for 0000:01:00.0 on minor 0
[ 20.199269] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa44000/0xa0000
[ 20.256227] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
[ 20.256234] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
[ 20.256250] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 20.256318] HDA Intel 0000:00:1b.0: irq 47 for MSI/MSI-X
[ 20.256352] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 20.265408] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input7
[ 20.466923] hda_codec: ALC888: BIOS auto-probing.
[ 20.534545] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 20.656814] type=1400 audit(1314619001.218:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=912 comm="apparmor_parser"
[ 20.657961] type=1400 audit(1314619001.218:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=912 comm="apparmor_parser"
[ 20.658564] type=1400 audit(1314619001.218:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=912 comm="apparmor_parser"
[ 20.661021] type=1400 audit(1314619001.222:8): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=911 comm="apparmor_parser"
[ 20.669569] type=1400 audit(1314619001.230:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=916 comm="apparmor_parser"
[ 20.671704] type=1400 audit(1314619001.230:10): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=916 comm="apparmor_parser"
[ 20.675532] type=1400 audit(1314619001.234:11): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=918 comm="apparmor_parser"
[ 20.855903] tg3 0000:02:00.0: irq 48 for MSI/MSI-X
[ 20.963103] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 21.043297] ppdev: user-space parallel port driver
[ 21.284923] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 24.548161] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[ 31.633057] wlan0: direct probe to 00:11:6b:46:dd:f0 (try 1/3)
[ 31.832041] wlan0: direct probe to 00:11:6b:46:dd:f0 (try 2/3)
[ 32.032025] wlan0: direct probe to 00:11:6b:46:dd:f0 (try 3/3)
[ 32.232029] wlan0: direct probe to 00:11:6b:46:dd:f0 timed out
[ 34.284064] iwlagn 0000:04:00.0: fail to flush all tx fifo queues
[ 39.321930] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[ 44.734551] wlan0: direct probe to 00:11:6b:46:dd:f0 (try 1/3)
[ 44.936041] wlan0: direct probe to 00:11:6b:46:dd:f0 (try 2/3)
[ 45.136038] wlan0: direct probe to 00:11:6b:46:dd:f0 (try 3/3)
[ 45.336027] wlan0: direct probe to 00:11:6b:46:dd:f0 timed out
[ 57.944216] wlan0: direct probe to 00:11:6b:46:dd:f0 (try 1/3)
[ 58.144034] wlan0: direct probe to 00:11:6b:46:dd:f0 (try 2/3)
[ 58.344054] wlan0: direct probe to 00:11:6b:46:dd:f0 (try 3/3)
[ 58.544027] wlan0: direct probe to 00:11:6b:46:dd:f0 timed out
[ 65.592176] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=600
[ 71.154977] wlan0: direct probe to 00:11:6b:46:dd:f0 (try 1/3)
[ 71.352081] wlan0: direct probe to 00:11:6b:46:dd:f0 (try 2/3)
[ 71.552067] wlan0: direct probe to 00:11:6b:46:dd:f0 (try 3/3)
[ 71.752070] wlan0: direct probe to 00:11:6b:46:dd:f0 timed out
[ 84.377010] wlan0: direct probe to 00:11:6b:46:dd:f0 (try 1/3)
[ 84.383860] wlan0: direct probe responded
[ 84.396034] wlan0: authenticate with 00:11:6b:46:dd:f0 (try 1)
[ 84.399316] wlan0: authenticated
[ 84.403663] wlan0: associate with 00:11:6b:46:dd:f0 (try 1)
[ 84.409975] wlan0: RX AssocResp from 00:11:6b:46:dd:f0 (capab=0x411 status=0 aid=1)
[ 84.409980] wlan0: associated
[ 84.422877] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 84.422948] cfg80211: Calling CRDA for country: TW
[ 84.428122] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428127] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm)
[ 84.428131] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428135] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm)
[ 84.428138] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428142] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm)
[ 84.428145] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428149] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm)
[ 84.428152] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428161] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm)
[ 84.428164] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428166] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm)
[ 84.428169] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428172] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm)
[ 84.428175] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428178] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm)
[ 84.428180] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428183] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm)
[ 84.428186] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428189] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm)
[ 84.428191] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428194] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm)
[ 84.428196] cfg80211: Disabling freq 2467 MHz
[ 84.428198] cfg80211: Disabling freq 2472 MHz
[ 84.428200] cfg80211: Disabling freq 5180 MHz
[ 84.428202] cfg80211: Disabling freq 5200 MHz
[ 84.428204] cfg80211: Disabling freq 5220 MHz
[ 84.428205] cfg80211: Disabling freq 5240 MHz
[ 84.428207] cfg80211: Disabling freq 5260 MHz
[ 84.428209] cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428212] cfg80211: 5270000 KHz - 5330000 KHz @ KHz), (300 mBi, 1700 mBm)
[ 84.428215] cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428218] cfg80211: 5270000 KHz - 5330000 KHz @ KHz), (300 mBi, 1700 mBm)
[ 84.428220] cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428223] cfg80211: 5270000 KHz - 5330000 KHz @ KHz), (300 mBi, 1700 mBm)
[ 84.428226] cfg80211: Disabling freq 5500 MHz
[ 84.428228] cfg80211: Disabling freq 5520 MHz
[ 84.428229] cfg80211: Disabling freq 5540 MHz
[ 84.428231] cfg80211: Disabling freq 5560 MHz
[ 84.428233] cfg80211: Disabling freq 5580 MHz
[ 84.428235] cfg80211: Disabling freq 5600 MHz
[ 84.428236] cfg80211: Disabling freq 5620 MHz
[ 84.428238] cfg80211: Disabling freq 5640 MHz
[ 84.428240] cfg80211: Disabling freq 5660 MHz
[ 84.428242] cfg80211: Disabling freq 5680 MHz
[ 84.428243] cfg80211: Disabling freq 5700 MHz
[ 84.428245] cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428249] cfg80211: 5735000 KHz - 5815000 KHz @ KHz), (300 mBi, 3000 mBm)
[ 84.428251] cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428254] cfg80211: 5735000 KHz - 5815000 KHz @ KHz), (300 mBi, 3000 mBm)
[ 84.428257] cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428260] cfg80211: 5735000 KHz - 5815000 KHz @ KHz), (300 mBi, 3000 mBm)
[ 84.428262] cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule:
[ 84.428265] cfg80211: 5735000 KHz - 5815000 KHz @ KHz), (300 mBi, 3000 mBm)
[ 84.428267] cfg80211: Disabling freq 5825 MHz
[ 84.428271] cfg80211: Regulatory domain changed to country: TW
[ 84.428273] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 84.428276] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 84.428279] cfg80211: (5270000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 84.428282] cfg80211: (5735000 KHz - 5815000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 85.595974] Intel AES-NI instructions are not detected.
[ 85.628613] padlock_aes: VIA PadLock not detected.
[ 95.024019] wlan0: no IPv6 routers present
[ 103.303262] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[ 140.915595] iwlagn 0000:04:00.0: Aggregation not enabled for tid 0 because load = 0
[ 145.595849] iwlagn 0000:04:00.0: Aggregation not enabled for tid 0 because load = 1
[ 151.604219] iwlagn 0000:04:00.0: iwlagn_tx_agg_start on ra = 00:11:6b:46:dd:f0 tid = 0
mark@MOON-5738:~$


Είμαι συνδεδεμένος με το wireless.Δεν είμαι σίγουρος κατα πόσο θα μείνω συνδεδεμένος.
Όσο είμαι συνδεδεμένος δώστε μου εντολές για να δούμε τι δεν πάει καλά.

[Mark on Moon]

Μήπως υπάρχει πρόβλημα με τον πυρήνα linux? Είδα απο osarena και είπα να βάλω τον 3.

Κώδικας: Επιλογή όλων

mark@MOON-5738:~$ uname -a
Linux MOON-5738 3.0.0-8-generic-pae #11-Ubuntu SMP Fri Aug 12 22:20:08 UTC 2011 i686 i686 i386 GNU/Linux


[logari81]

δεν χανεις τίποτα να δοκιμάσεις έναν πιο φρέσκο πυρήνα.

[Mark on Moon]

Μιλώντας για το wireless, το πρόβλημα εμφανίστηκε μετά την αλλαγή πυρήνα.

[Mark on Moon]

Εξακολουθεί να μην συνδέεται με τον wireless , παρα μονο για λίγο ( μπορεί 2 ώρες ή 2 λεπτά).

[Mark on Moon]

Λοιπόν , λίγο την προσοχή σας παρακαλώ!

Έκανα clean install και παρόλαυτα συνεχίζει τα ίδια : Βλέπει την σύνδεση , πατάω να συνδεθώ , ζητάει κωδικό . βάζω κωδικό , το εικονίδιο της σύνδεσης γυρνάει και τέλος ΔΕΝ συνδέεται!

Υπάρχει κάποια περίπτωση να είναι πρόβλημα της κάρτας?????

[dim459]

'Οταν o ρούτερ είναι ξεκλείδωτος συνδέεται ;
Αν αλλάξεις στο ρούτερ κανάλι εκπομπής ή και τύπο κρυπτογράφησης συνδέεται ;

[Mark on Moon]

'Οταν o ρούτερ είναι ξεκλείδωτος συνδέεται ;
Αν αλλάξεις στο ρούτερ κανάλι εκπομπής ή και τύπο κρυπτογράφησης συνδέεται ;

Συνδέομαι με access point και δεν ξερω πως να αλλαξω κανάλι η να φτιαχνω μια σύνδεση. Αυτο που έκανα ειναι να κάνω reset το access point για να μην έχει κωδικό και πάλι δεν συνδέεται..