Netgear WG111v3 USB Μερικές ερωτήσεις

[logari81]

πόσταρε το αποτελεσμα της εντολής

Κώδικας: Επιλογή όλων

dmesg

και της εντολής

Κώδικας: Επιλογή όλων

ping -c 3 150.140.170.53

[@ntonius]

@ntonius ίσως να είναι και μεμονωμένο το πρόβλημα (;)

τα αποτελέσματα του iwconfig

Κώδικας: Επιλογή όλων

trala@trala-desktop:~$ iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

pan0 no wireless extensions.

wmaster0 no wireless extensions.

wlan2 IEEE 802.11bg ESSID:"on"
Mode:Managed Frequency:2.452 GHz Access Point: 00:1C:A2:AC:DF:9D
Bit Rate=54 Mb/s Tx-Power=20 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Power Management:off
Link Quality=44/100 Signal level:-49 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

Σε αυτό λέει ότι βρήκε μια ασύρματη σύνδεση με ονομασία ''on'' για το wlan2

Κανονικά η εντολή σύνδεσης γι αυτό είναι

Κώδικας: Επιλογή όλων

sudo iwconfig wlan2 essid on

Έχεις δοκιμάσει να συνδεθείς με αυτή την εντολή?

[logari81]

Κανονικά η εντολή σύνδεσης γι αυτό είναι

από τι μας ειπε δεν εχει προβλημα να συνθεθει με το ρουτερ αλλα με το να μπει στο ιντερνετ οπότε μπορει να μην εχει σχεση καν με την καρτα

[testz0r]

τα αποτελέσματα της dmesg:

Κώδικας: Επιλογή όλων

[ 0.004000] vmalloc : 0xf7bfe000 - 0xff3fe000 ( 120 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf73fe000 ( 883 MB)
[ 0.004000] .init : 0xc0733000 - 0xc07b8000 ( 532 kB)
[ 0.004000] .data : 0xc05050ff - 0xc072ae60 (2199 kB)
[ 0.004000] .text : 0xc0100000 - 0xc05050ff (4116 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] SLUB: Genslabs=12, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.004027] Calibrating delay loop (skipped), value calculated using timer frequency.. 4799.76 BogoMIPS (lpj=9599528)
[ 0.004072] Security Framework initialized
[ 0.004090] SELinux: Disabled at boot.
[ 0.004128] AppArmor: AppArmor initialized
[ 0.004157] Mount-cache hash table entries: 512
[ 0.004493] Initializing cgroup subsys ns
[ 0.004508] Initializing cgroup subsys cpuacct
[ 0.004512] Initializing cgroup subsys memory
[ 0.004525] Initializing cgroup subsys freezer
[ 0.004563] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 0.004568] CPU: L2 cache: 128K
[ 0.004573] CPU: Hyper-Threading is disabled
[ 0.004606] Checking 'hlt' instruction... OK.
[ 0.021052] SMP alternatives: switching to UP code
[ 0.236057] ACPI: Core revision 20080926
[ 0.241338] ACPI: Checking initramfs for custom DSDT
[ 0.612290] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.652024] CPU0: Intel(R) Celeron(R) CPU 2.40GHz stepping 09
[ 0.656002] Brought up 1 CPUs
[ 0.656002] Total of 1 processors activated (4799.76 BogoMIPS).
[ 0.656002] CPU0 attaching NULL sched-domain.
[ 0.656002] net_namespace: 776 bytes
[ 0.656002] Booting paravirtualized kernel on bare hardware
[ 0.656002] Time: 8:13:32 Date: 10/20/09
[ 0.656002] regulator: core version 0.5
[ 0.656002] NET: Registered protocol family 16
[ 0.656002] EISA bus registered
[ 0.656002] ACPI: bus type pci registered
[ 0.664260] PCI: PCI BIOS revision 2.10 entry at 0xfb5b0, last bus=1
[ 0.664265] PCI: Using configuration type 1 for base access
[ 0.667231] ACPI: EC: Look up EC in DSDT
[ 0.675641] ACPI: Interpreter enabled
[ 0.675657] ACPI: (supports S0 S1 S4 S5)
[ 0.675702] ACPI: Using IOAPIC for interrupt routing
[ 0.684020] ACPI: No dock devices found.
[ 0.684068] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.684178] pci 0000:00:00.0: reg 10 32bit mmio: [0xe8000000-0xebffffff]
[ 0.684270] pci 0000:00:01.0: supports D1
[ 0.684314] pci 0000:00:08.0: reg 10 io port: [0xd000-0xd01f]
[ 0.684356] pci 0000:00:08.0: supports D1 D2
[ 0.684391] pci 0000:00:08.1: reg 10 io port: [0xd400-0xd407]
[ 0.684433] pci 0000:00:08.1: supports D1 D2
[ 0.684508] pci 0000:00:10.0: reg 20 io port: [0xd800-0xd81f]
[ 0.684529] pci 0000:00:10.0: supports D1 D2
[ 0.684532] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.684538] pci 0000:00:10.0: PME# disabled
[ 0.684595] pci 0000:00:10.1: reg 20 io port: [0xdc00-0xdc1f]
[ 0.684616] pci 0000:00:10.1: supports D1 D2
[ 0.684619] pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.684624] pci 0000:00:10.1: PME# disabled
[ 0.684681] pci 0000:00:10.2: reg 20 io port: [0xe000-0xe01f]
[ 0.684703] pci 0000:00:10.2: supports D1 D2
[ 0.684705] pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.684710] pci 0000:00:10.2: PME# disabled
[ 0.684747] pci 0000:00:10.3: reg 10 32bit mmio: [0xee000000-0xee0000ff]
[ 0.684788] pci 0000:00:10.3: supports D1 D2
[ 0.684791] pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.684796] pci 0000:00:10.3: PME# disabled
[ 0.684873] HPET not enabled in BIOS. You might try hpet=force boot option
[ 0.684883] pci 0000:00:11.0: quirk: region 0400-047f claimed by vt8235 PM
[ 0.684888] pci 0000:00:11.0: quirk: region 0500-050f claimed by vt8235 SMB
[ 0.684954] pci 0000:00:11.1: reg 20 io port: [0xe400-0xe40f]
[ 0.685021] pci 0000:00:12.0: reg 10 io port: [0xe800-0xe8ff]
[ 0.685029] pci 0000:00:12.0: reg 14 32bit mmio: [0xee001000-0xee0010ff]
[ 0.685066] pci 0000:00:12.0: supports D1 D2
[ 0.685068] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.685073] pci 0000:00:12.0: PME# disabled
[ 0.685137] pci 0000:01:00.0: reg 10 32bit mmio: [0xec000000-0xecffffff]
[ 0.685145] pci 0000:01:00.0: reg 14 32bit mmio: [0xe0000000-0xe7ffffff]
[ 0.685169] pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x00ffff]
[ 0.685225] pci 0000:00:01.0: bridge 32bit mmio: [0xec000000-0xedffffff]
[ 0.685230] pci 0000:00:01.0: bridge 32bit mmio pref: [0xe0000000-0xe7ffffff]
[ 0.685241] bus 00 -> node 0
[ 0.685260] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.721243] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
[ 0.721594] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[ 0.721938] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[ 0.722281] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
[ 0.722633] ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0
[ 0.722978] ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0
[ 0.723360] ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0
[ 0.723699] ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0
[ 0.724084] ACPI: WMI: Mapper loaded
[ 0.724606] SCSI subsystem initialized
[ 0.724810] libata version 3.00 loaded.
[ 0.724993] usbcore: registered new interface driver usbfs
[ 0.725046] usbcore: registered new interface driver hub
[ 0.725185] usbcore: registered new device driver usb
[ 0.725616] PCI: Using ACPI for IRQ routing
[ 0.725817] Bluetooth: Core ver 2.13
[ 0.725817] NET: Registered protocol family 31
[ 0.725817] Bluetooth: HCI device and connection manager initialized
[ 0.725817] Bluetooth: HCI socket layer initialized
[ 0.725817] NET: Registered protocol family 8
[ 0.725817] NET: Registered protocol family 20
[ 0.725817] NetLabel: Initializing
[ 0.725817] NetLabel: domain hash size = 128
[ 0.725817] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.725817] NetLabel: unlabeled traffic allowed by default
[ 0.725817] AppArmor: AppArmor Filesystem Enabled
[ 0.725817] pnp: PnP ACPI init
[ 0.725817] ACPI: bus type pnp registered
[ 0.732676] pnp: PnP ACPI: found 12 devices
[ 0.732684] ACPI: ACPI bus type pnp unregistered
[ 0.732693] PnPBIOS: Disabled by ACPI PNP
[ 0.732724] system 00:00: iomem range 0xd0000-0xd3fff has been reserved
[ 0.732729] system 00:00: iomem range 0xf0000-0xf7fff could not be reserved
[ 0.732732] system 00:00: iomem range 0xf8000-0xfbfff could not be reserved
[ 0.732735] system 00:00: iomem range 0xfc000-0xfffff could not be reserved
[ 0.732739] system 00:00: iomem range 0x7fff0000-0x7fffffff could not be reserved
[ 0.732744] system 00:00: iomem range 0xffff0000-0xffffffff has been reserved
[ 0.732747] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 0.732751] system 00:00: iomem range 0x100000-0x7ffeffff could not be reserved
[ 0.732754] system 00:00: iomem range 0xfec00000-0xfecfffff has been reserved
[ 0.732758] system 00:00: iomem range 0xfee00000-0xfeefffff has been reserved
[ 0.732761] system 00:00: iomem range 0xfff80000-0xfffeffff has been reserved
[ 0.732775] system 00:02: ioport range 0x400-0x47f has been reserved
[ 0.732779] system 00:02: ioport range 0x500-0x50f has been reserved
[ 0.732789] system 00:03: ioport range 0x4d0-0x4d1 has been reserved
[ 0.732793] system 00:03: ioport range 0x800-0x805 has been reserved
[ 0.732796] system 00:03: ioport range 0x290-0x297 has been reserved
[ 0.767693] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.767699] pci 0000:00:01.0: IO window: disabled
[ 0.767707] pci 0000:00:01.0: MEM window: 0xec000000-0xedffffff
[ 0.767712] pci 0000:00:01.0: PREFETCH window: 0x000000e0000000-0x000000e7ffffff
[ 0.767732] pci 0000:00:01.0: setting latency timer to 64
[ 0.767738] bus: 00 index 0 io port: [0x00-0xffff]
[ 0.767741] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[ 0.767744] bus: 01 index 0 mmio: [0x0-0x0]
[ 0.767747] bus: 01 index 1 mmio: [0xec000000-0xedffffff]
[ 0.767749] bus: 01 index 2 mmio: [0xe0000000-0xe7ffffff]
[ 0.767752] bus: 01 index 3 mmio: [0x0-0x0]
[ 0.767775] NET: Registered protocol family 2
[ 0.768066] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.768736] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.770704] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.771724] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.771730] TCP reno registered
[ 0.772097] NET: Registered protocol family 1
[ 0.772348] checking if image is initramfs... it is
[ 1.268069] Switched to high resolution mode on CPU 0
[ 1.574094] Freeing initrd memory: 7386k freed
[ 1.574235] cpufreq: No nForce2 chipset.
[ 1.574534] audit: initializing netlink socket (disabled)
[ 1.574575] type=2000 audit(1256026412.572:1): initialized
[ 1.582484] highmem bounce pool size: 64 pages
[ 1.582502] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.584417] VFS: Disk quotas dquot_6.5.1
[ 1.584561] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.586014] fuse init (API version 7.10)
[ 1.586238] msgmni has been set to 1698
[ 1.586808] alg: No test for stdrng (krng)
[ 1.586876] io scheduler noop registered
[ 1.586881] io scheduler anticipatory registered
[ 1.586883] io scheduler deadline registered
[ 1.586951] io scheduler cfq registered (default)
[ 1.586973] PCI: VIA PCI bridge detected.Disabling DAC.
[ 1.587091] pci 0000:01:00.0: Boot video device
[ 1.592503] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.592522] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.592819] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 1.592826] ACPI: Power Button (FF) [PWRF]
[ 1.592919] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 1.592924] ACPI: Power Button (CM) [PWRB]
[ 1.593047] fan PNP0C0B:00: registered as cooling_device0
[ 1.593060] ACPI: Fan [FAN] (on)
[ 1.593525] processor ACPI_CPU:00: registered as cooling_device1
[ 1.597592] thermal LNXTHERM:01: registered as thermal_zone0
[ 1.598054] ACPI: Thermal Zone [THRM] (30 C)
[ 1.598196] isapnp: Scanning for PnP cards...
[ 1.952330] isapnp: No Plug & Play device found
[ 1.954831] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 1.955008] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.955628] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.957458] brd: module loaded
[ 1.958414] loop: module loaded
[ 1.958646] Fixed MDIO Bus: probed
[ 1.958659] PPP generic driver version 2.4.2
[ 1.958810] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 1.958907] Driver 'sd' needs updating - please use bus_type methods
[ 1.958943] Driver 'sr' needs updating - please use bus_type methods
[ 1.959908] pata_via 0000:00:11.1: version 0.3.3
[ 1.960474] ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
[ 1.960482] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
[ 1.960499] pata_via 0000:00:11.1: PCI INT A -> Link[ALKA] -> GSI 20 (level, low) -> IRQ 20
[ 1.960909] scsi0 : pata_via
[ 1.961208] scsi1 : pata_via
[ 1.964990] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xe400 irq 14
[ 1.964997] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xe408 irq 15
[ 2.136431] ata1.01: ATAPI: HL-DT-STDVD-ROM GDR8163B, 0L23, max UDMA/33
[ 2.152317] ata1.01: configured for UDMA/33
[ 2.325337] ata2.01: ATA-5: WDC WD200EB-00BHF0, 15.15M15, max UDMA/100
[ 2.325342] ata2.01: 39102336 sectors, multi 16: LBA
[ 2.341181] ata2.01: configured for UDMA/100
[ 2.349749] scsi 0:0:1:0: CD-ROM HL-DT-ST DVD-ROM GDR8163B 0L23 PQ: 0 ANSI: 5
[ 2.357598] sr0: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
[ 2.357608] Uniform CD-ROM driver Revision: 3.20
[ 2.357864] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 2.358025] sr 0:0:1:0: Attached scsi generic sg0 type 5
[ 2.358307] scsi 1:0:1:0: Direct-Access ATA WDC WD200EB-00BH 15.1 PQ: 0 ANSI: 5
[ 2.358637] sd 1:0:1:0: [sda] 39102336 512-byte hardware sectors: (20.0 GB/18.6 GiB)
[ 2.358710] sd 1:0:1:0: [sda] Write Protect is off
[ 2.358715] sd 1:0:1:0: [sda] Mode Sense: 00 3a 00 00
[ 2.358836] sd 1:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.359086] sd 1:0:1:0: [sda] 39102336 512-byte hardware sectors: (20.0 GB/18.6 GiB)
[ 2.359158] sd 1:0:1:0: [sda] Write Protect is off
[ 2.359163] sd 1:0:1:0: [sda] Mode Sense: 00 3a 00 00
[ 2.359279] sd 1:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.359291] sda: sda1 sda2 < sda5 >
[ 2.425440] sd 1:0:1:0: [sda] Attached SCSI disk
[ 2.425568] sd 1:0:1:0: Attached scsi generic sg1 type 0
[ 2.425965] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.426477] ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using IRQ 21
[ 2.426484] ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
[ 2.426502] ehci_hcd 0000:00:10.3: PCI INT D -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 2.426554] ehci_hcd 0000:00:10.3: EHCI Host Controller
[ 2.426791] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
[ 2.426907] ehci_hcd 0000:00:10.3: irq 21, io mem 0xee000000
[ 2.436037] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00
[ 2.436238] usb usb1: configuration #1 chosen from 1 choice
[ 2.436306] hub 1-0:1.0: USB hub found
[ 2.436335] hub 1-0:1.0: 6 ports detected
[ 2.436650] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.436708] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.436837] uhci_hcd 0000:00:10.0: PCI INT A -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 2.436857] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 2.437011] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 2.437053] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000d800
[ 2.437311] usb usb2: configuration #1 chosen from 1 choice
[ 2.437376] hub 2-0:1.0: USB hub found
[ 2.437408] hub 2-0:1.0: 2 ports detected
[ 2.437694] uhci_hcd 0000:00:10.1: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 2.437713] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 2.437863] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 2.437904] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000dc00
[ 2.438112] usb usb3: configuration #1 chosen from 1 choice
[ 2.438192] hub 3-0:1.0: USB hub found
[ 2.438219] hub 3-0:1.0: 2 ports detected
[ 2.438493] uhci_hcd 0000:00:10.2: PCI INT C -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 2.438513] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 2.438661] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[ 2.438702] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000e000
[ 2.438930] usb usb4: configuration #1 chosen from 1 choice
[ 2.439006] hub 4-0:1.0: USB hub found
[ 2.439031] hub 4-0:1.0: 2 ports detected
[ 2.439399] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 2.439405] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 2.439602] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.439975] mice: PS/2 mouse device common for all mice
[ 2.440512] rtc_cmos 00:05: RTC can wake from S4
[ 2.440622] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 2.440686] rtc0: alarms up to one year, y3k, 242 bytes nvram
[ 2.440863] device-mapper: uevent: version 1.0.3
[ 2.441277] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 2.441523] device-mapper: multipath: version 1.0.5 loaded
[ 2.441532] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 2.441872] EISA: Probing bus 0 at eisa.0
[ 2.441927] EISA: Detected 0 cards.
[ 2.442061] cpuidle: using governor ladder
[ 2.442067] cpuidle: using governor menu
[ 2.443010] TCP cubic registered
[ 2.443242] NET: Registered protocol family 10
[ 2.444151] lo: Disabled Privacy Extensions
[ 2.444637] NET: Registered protocol family 17
[ 2.444719] Bluetooth: L2CAP ver 2.11
[ 2.444722] Bluetooth: L2CAP socket layer initialized
[ 2.444726] Bluetooth: SCO (Voice Link) ver 0.6
[ 2.444728] Bluetooth: SCO socket layer initialized
[ 2.444875] Bluetooth: RFCOMM socket layer initialized
[ 2.444900] Bluetooth: RFCOMM TTY layer initialized
[ 2.444903] Bluetooth: RFCOMM ver 1.10
[ 2.445074] Using IPI No-Shortcut mode
[ 2.445362] registered taskstats version 1
[ 2.445539] Magic number: 13:541:220
[ 2.445638] dmi id: hash matches
[ 2.445693] rtc_cmos 00:05: setting system clock to 2009-10-20 08:13:33 UTC (1256026413)
[ 2.445699] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.445701] EDD information not available.
[ 2.446806] Freeing unused kernel memory: 532k freed
[ 2.446977] Write protecting the kernel text: 4120k
[ 2.447023] Write protecting the kernel read-only data: 1524k
[ 2.464775] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 2.804087] usb 1-5: new high speed USB device using ehci_hcd and address 3
[ 3.110392] Floppy drive(s): fd0 is 1.44M
[ 3.131696] FDC 0 is a post-1991 82077
[ 3.139180] usb 1-5: configuration #1 chosen from 1 choice
[ 3.376131] usb 2-1: new low speed USB device using uhci_hcd and address 2
[ 3.412158] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 3.412170] via-rhine: Broken BIOS detected, avoid_D3 enabled.
[ 3.412729] ACPI: PCI Interrupt Link [ALKD] BIOS reported IRQ 0, using IRQ 23
[ 3.412736] ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
[ 3.412757] via-rhine 0000:00:12.0: PCI INT A -> Link[ALKD] -> GSI 23 (level, low) -> IRQ 23
[ 3.413889] eth0: VIA Rhine II at 0xee001000, 00:30:18:a1:19:5a, IRQ 23.
[ 3.414603] eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
[ 3.562954] usb 2-1: configuration #1 chosen from 1 choice
[ 4.262654] usbcore: registered new interface driver hiddev
[ 4.278534] input: Microsoft Comfort Optical Mouse 1000 as /devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.0/input/input4
[ 4.279766] generic-usb 0003:045E:00F6.0001: input,hidraw0: USB HID v1.11 Mouse [Microsoft Comfort Optical Mouse 1000] on usb-0000:00:10.0-1/input0
[ 4.279816] usbcore: registered new interface driver usbhid
[ 4.279823] usbhid: v2.6:USB HID core driver
[ 4.404054] PM: Starting manual resume from disk
[ 4.404062] PM: Resume from partition 8:5
[ 4.404065] PM: Checking hibernation image.
[ 4.404378] PM: Resume from disk failed.
[ 4.455785] kjournald starting. Commit interval 5 seconds
[ 4.455823] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.466817] udev: starting version 141
[ 13.741711] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 13.767612] Linux agpgart interface v0.103
[ 13.848106] agpgart: Detected VIA P4M266x/P4N266 chipset
[ 13.853636] agpgart-via 0000:00:00.0: AGP aperture is 64M @ 0xe8000000
[ 14.002714] parport_pc 00:0a: reported by Plug and Play ACPI
[ 14.002770] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 14.076288] gameport: EMU10K1 is pci0000:00:08.1/gameport0, io 0xd400, speed 1084kHz
[ 14.356239] cfg80211: Calling CRDA to update world regulatory domain
[ 14.440781] irda_init()
[ 14.440815] NET: Registered protocol family 23
[ 15.334769] EMU10K1_Audigy 0000:00:08.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 15.581257] phy0: Selected rate control algorithm 'pid'
[ 15.661322] Registered led device: rt73usb-phy0:radio
[ 15.661522] Registered led device: rt73usb-phy0:assoc
[ 15.661734] Registered led device: rt73usb-phy0:quality
[ 15.662370] usbcore: registered new interface driver rt73usb
[ 15.888239] ppdev: user-space parallel port driver
[ 16.061052] cfg80211: World regulatory domain updated:
[ 16.061062] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 16.061067] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 16.061070] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 16.061073] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 16.061076] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 16.061079] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 16.522700] lp0: using parport0 (interrupt-driven).
[ 16.807784] Adding 859436k swap on /dev/sda5. Priority:-1 extents:1 across:859436k
[ 17.438785] EXT3 FS on sda1, internal journal
[ 19.287315] type=1505 audit(1256026430.338:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=1900
[ 19.386710] type=1505 audit(1256026430.438:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=1904
[ 19.387221] type=1505 audit(1256026430.438:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=1904
[ 19.387559] type=1505 audit(1256026430.438:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=1904
[ 19.387871] type=1505 audit(1256026430.438:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=1904
[ 19.636363] type=1505 audit(1256026430.690:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=1909
[ 19.637107] type=1505 audit(1256026430.690:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=1909
[ 19.701978] type=1505 audit(1256026430.754:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=1913
[ 24.984213] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 24.984218] Bluetooth: BNEP filters: protocol multicast
[ 25.019741] Bridge firewalling registered
[ 30.947353] eth0: link down
[ 30.947635] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 30.950989] rt73usb 1-5:1.0: firmware: requesting rt73.bin
[ 31.207126] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 64.034622] wlan0: authenticate with AP 00:1c:a2:ac:df:9d
[ 64.036788] wlan0: authenticated
[ 64.036799] wlan0: associate with AP 00:1c:a2:ac:df:9d
[ 64.058864] wlan0: RX AssocResp from 00:1c:a2:ac:df:9d (capab=0x471 status=0 aid=1)
[ 64.058871] wlan0: associated
[ 64.067937] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 74.756085] wlan0: no IPv6 routers present
[ 175.908416] usb 1-5: USB disconnect, address 3
[ 175.912970] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x3040 with error -19.
[ 175.912982] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3040 with error -19.
[ 175.912988] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3028 with error -19.
[ 175.912993] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3064 with error -19.
[ 175.912998] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0c failed for offset 0x0000 with error -19.
[ 175.913044] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.
[ 175.913384] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.
[ 175.913452] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.
[ 175.913512] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.
[ 176.021595] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x30a0 with error -19.
[ 176.021608] phy0 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x30a0 with error -19.
[ 178.520072] usb 1-5: new high speed USB device using ehci_hcd and address 4
[ 178.710119] usb 1-5: configuration #1 chosen from 1 choice
[ 179.268032] rtl8187: 8187B chip detected. Support is EXPERIMENTAL, and could damage your
[ 179.268038] hardware, use at your own risk
[ 179.270608] phy1: Selected rate control algorithm 'pid'
[ 179.274501] phy1: hwaddr 00:1b:2f:c6:bb:6e, RTL8187BvE V0 + rtl8225z2
[ 179.274584] usbcore: registered new interface driver rtl8187
[ 179.435097] udev: renamed network interface wlan0 to wlan2
[ 199.929654] ADDRCONF(NETDEV_UP): wlan2: link is not ready
[ 208.141352] wlan2: authenticate with AP 00:1c:a2:ac:df:9d
[ 208.143778] wlan2: authenticated
[ 208.143788] wlan2: associate with AP 00:1c:a2:ac:df:9d
[ 208.148264] wlan2: RX AssocResp from 00:1c:a2:ac:df:9d (capab=0x471 status=0 aid=2)
[ 208.148270] wlan2: associated
[ 208.194605] ADDRCONF(NETDEV_CHANGE): wlan2: link becomes ready
[ 218.412041] wlan2: no IPv6 routers present
[ 366.442787] usb 1-5: USB disconnect, address 4
[ 369.000100] usb 1-5: new high speed USB device using ehci_hcd and address 5
[ 369.374874] usb 1-5: configuration #1 chosen from 1 choice
[ 369.643548] phy2: Selected rate control algorithm 'pid'
[ 369.646662] Registered led device: rt73usb-phy2:radio
[ 369.646715] Registered led device: rt73usb-phy2:assoc
[ 369.646760] Registered led device: rt73usb-phy2:quality
[ 373.948966] rt73usb 1-5:1.0: firmware: requesting rt73.bin
[ 374.079084] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 431.976346] wlan0: authenticate with AP 00:1c:a2:ac:df:9d
[ 431.979898] wlan0: authenticated
[ 431.979907] wlan0: associate with AP 00:1c:a2:ac:df:9d
[ 432.002310] wlan0: RX AssocResp from 00:1c:a2:ac:df:9d (capab=0x471 status=0 aid=1)
[ 432.002328] wlan0: associated
[ 432.056161] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 442.608073] wlan0: no IPv6 routers present
[ 3087.909852] usb 1-5: USB disconnect, address 5
[ 3087.914795] phy2 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x3040 with error -19.
[ 3087.914808] phy2 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3040 with error -19.
[ 3087.914813] phy2 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3028 with error -19.
[ 3087.914818] phy2 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x3064 with error -19.
[ 3087.914822] phy2 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0c failed for offset 0x0000 with error -19.
[ 3087.914870] phy2 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.
[ 3087.915161] phy2 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.
[ 3087.915224] phy2 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.
[ 3087.915283] phy2 -> rt2x00usb_vendor_request: Error - Vendor Request 0x0a failed for offset 0x0000 with error -19.
[ 3088.016824] phy2 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x30a0 with error -19.
[ 3088.016835] phy2 -> rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x30a0 with error -19.
[ 3094.104077] usb 1-5: new high speed USB device using ehci_hcd and address 6
[ 3094.289730] usb 1-5: configuration #1 chosen from 1 choice
[ 3094.660951] rtl8187: 8187B chip detected. Support is EXPERIMENTAL, and could damage your
[ 3094.660957] hardware, use at your own risk
[ 3094.671310] phy3: Selected rate control algorithm 'pid'
[ 3094.676923] phy3: hwaddr 00:1b:2f:c6:bb:6e, RTL8187BvE V0 + rtl8225z2
[ 3094.724997] udev: renamed network interface wlan0 to wlan2
[ 3115.349639] ADDRCONF(NETDEV_UP): wlan2: link is not ready
[ 3123.553361] wlan2: authenticate with AP 00:1c:a2:ac:df:9d
[ 3123.555125] wlan2: authenticated
[ 3123.555133] wlan2: associate with AP 00:1c:a2:ac:df:9d
[ 3123.557930] wlan2: RX AssocResp from 00:1c:a2:ac:df:9d (capab=0x471 status=0 aid=2)
[ 3123.557937] wlan2: associated
[ 3123.596596] ADDRCONF(NETDEV_CHANGE): wlan2: link becomes ready
[ 3133.924043] wlan2: no IPv6 routers present

και του ping:

Κώδικας: Επιλογή όλων

trala@trala-desktop:~$ ping -c 3 150.140.170.53
PING 150.140.170.53 (150.140.170.53) 56(84) bytes of data.
From 192.168.1.3 icmp_seq=1 Destination Host Unreachable
From 192.168.1.3 icmp_seq=2 Destination Host Unreachable
From 192.168.1.3 icmp_seq=3 Destination Host Unreachable

--- 150.140.170.53 ping statistics ---
3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2016ms
, pipe 3

Αυτό όμως που θα σας πω ίσως σας ενδιαφέρει: Ενώ είμαι συνδεδεμένος στο router αλλά δεν μπορώ να μπω σε κάποια ιστοσελίδα, μόλις δίνω την εντολή

Κώδικας: Επιλογή όλων

sudo iwconfig wlan2 essid on

που έγραψε ο @ntonius μπάινω στις ιστοσελίδες κανονικά. Μετά από λιγότερο από 10 δευτερόλεπτα πάλι δεν μπορώ να μπω πουθενά.

[logari81]

απότι βλεπω στο αποτελεσμα του dmesg γινεται καποιο conflict μεταξυ των δυο καρτων που έχεις. Δώσε μας το αποτελεσμα του

Κώδικας: Επιλογή όλων

lspci -nn

για να δουμε ποια ακριβώς ειναι η άλλη καρτα που έχεις και μετα αποσυνδεσέ την και ξαναδοκίμασε με μονο την usb συνδεμενη.

[testz0r]

τα αποτελέσματα που έδωσα και πάνω τα "πήρα" ενώ είχα μόνο το netgear wireless συνδεδεμένο (όπως και τα παραπάνω αποτελέσματα)

Κώδικας: Επιλογή όλων

trala@trala-desktop:~$ lspci -nn
00:00.0 Host bridge [0600]: VIA Technologies, Inc. P4M266 Host Bridge [1106:3148]
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] [1106:b091]
00:08.0 Multimedia audio controller [0401]: Creative Labs SB Live! EMU10k1 [1102:0002] (rev 0a)
00:08.1 Input device controller [0980]: Creative Labs SB Live! Game Port [1102:7002] (rev 0a)
00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80)
00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80)
00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80)
00:10.3 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 82)
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8235 ISA Bridge [1106:3177]
00:11.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06)
00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 74)
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV11 [GeForce2 MX/MX 400] [10de:0110] (rev b2)

Ίσως φταίει κάτι από αυτά πάνω. Πάντως όταν έτρεξα δοκιμαστικά το liveCD και όταν εγκατέστησα για πρώτη φορά το ubuntu δοκίμασα πρώτα την netgear και υπήρχε και τότε το πρόβλημα όποτε αποκλείεται να φταίει η άλλη κάρτα μου (ασύρματη και αυτή).

[vagrale13]

@testz0r
Για δες εδω το δευτερο βιντεο viewtopic.php?f=9&t=895
και κανε τις ρυθμισεις στο Δικτυο, μηπως ειναι εκει το προβλημα.....

[logari81]

επίσης θα μπορουσες να ερθεις εδώ:
http://ubuntu-gr.org/webchat
να το συζητήσουμε.

[testz0r]

εκκίνηση του pc με συνδεδεμένο (μόνο) το netgear wireless:
εντολή:dmesg

Κώδικας: Επιλογή όλων


[ 0.000000] ACPI: RSDT 7FFF3000, 002C (r1 P4M266 AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: FACP 7FFF3040, 0074 (r1 P4M266 AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: DSDT 7FFF30C0, 3B08 (r1 P4M266 AWRDACPI 1000 MSFT 100000E)
[ 0.000000] ACPI: FACS 7FFF0000, 0040
[ 0.000000] ACPI: APIC 7FFF6C00, 0068 (r1 P4M266 AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 1163MB HIGHMEM available.
[ 0.000000] 883MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 373fe000
[ 0.000000] low ram: 00000000 - 373fe000
[ 0.000000] bootmap 00012000 - 00018e80
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00373fe000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0000100000 - 00008780ac] TEXT DATA BSS ==> [0000100000 - 00008780ac]
[ 0.000000] #4 [0000879000 - 000087d000] INIT_PG_TABLE ==> [0000879000 - 000087d000]
[ 0.000000] #5 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000]
[ 0.000000] #6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
[ 0.000000] #7 [000087d000 - 0000fb3949] NEW RAMDISK ==> [000087d000 - 0000fb3949]
[ 0.000000] #8 [0000012000 - 0000019000] BOOTMAP ==> [0000012000 - 0000019000]
[ 0.000000] found SMP MP-table at [c00f5500] 000f5500
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000373fe
[ 0.000000] HighMem 0x000373fe -> 0x0007fff0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x000000a0
[ 0.000000] 0: 0x00000100 -> 0x0007fff0
[ 0.000000] On node 0 totalpages: 524160
[ 0.000000] free_area_init_node: node 0, pgdat c06cb780, node_mem_map c1000200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3952 pages, LIFO batch:0
[ 0.000000] Normal zone: 1736 pages used for memmap
[ 0.000000] Normal zone: 220470 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2328 pages used for memmap
[ 0.000000] HighMem zone: 295642 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000)
[ 0.000000] PERCPU: Allocating 45056 bytes of per cpu data
[ 0.000000] NR_CPUS: 64, nr_cpu_ids: 2, nr_node_ids 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520064
[ 0.000000] Kernel command line: root=UUID=f4078667-808f-4263-bfdb-416e7ccb793f ro quiet splash
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2399.916 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] allocated 10485120 bytes of page_cgroup
[ 0.004000] please try cgroup_disable=memory option if you don't want
[ 0.004000] Scanning for low memory corruption every 60 seconds
[ 0.004000] Memory: 2053048k/2097088k available (4116k kernel code, 42632k reserved, 2199k data, 532k init, 1191880k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xffc77000 - 0xfffff000 (3616 kB)
[ 0.004000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.004000] vmalloc : 0xf7bfe000 - 0xff3fe000 ( 120 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf73fe000 ( 883 MB)
[ 0.004000] .init : 0xc0733000 - 0xc07b8000 ( 532 kB)
[ 0.004000] .data : 0xc05050ff - 0xc072ae60 (2199 kB)
[ 0.004000] .text : 0xc0100000 - 0xc05050ff (4116 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] SLUB: Genslabs=12, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.004028] Calibrating delay loop (skipped), value calculated using timer frequency.. 4799.83 BogoMIPS (lpj=9599664)
[ 0.004072] Security Framework initialized
[ 0.004091] SELinux: Disabled at boot.
[ 0.004129] AppArmor: AppArmor initialized
[ 0.004156] Mount-cache hash table entries: 512
[ 0.004495] Initializing cgroup subsys ns
[ 0.004510] Initializing cgroup subsys cpuacct
[ 0.004515] Initializing cgroup subsys memory
[ 0.004528] Initializing cgroup subsys freezer
[ 0.004569] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 0.004573] CPU: L2 cache: 128K
[ 0.004578] CPU: Hyper-Threading is disabled
[ 0.004611] Checking 'hlt' instruction... OK.
[ 0.021053] SMP alternatives: switching to UP code
[ 0.228050] ACPI: Core revision 20080926
[ 0.234746] ACPI: Checking initramfs for custom DSDT
[ 0.605121] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.644847] CPU0: Intel(R) Celeron(R) CPU 2.40GHz stepping 09
[ 0.648002] Brought up 1 CPUs
[ 0.648002] Total of 1 processors activated (4799.83 BogoMIPS).
[ 0.648002] CPU0 attaching NULL sched-domain.
[ 0.648002] net_namespace: 776 bytes
[ 0.648002] Booting paravirtualized kernel on bare hardware
[ 0.648002] Time: 12:01:58 Date: 10/20/09
[ 0.648002] regulator: core version 0.5
[ 0.648002] NET: Registered protocol family 16
[ 0.648002] EISA bus registered
[ 0.648002] ACPI: bus type pci registered
[ 0.656257] PCI: PCI BIOS revision 2.10 entry at 0xfb5b0, last bus=1
[ 0.656262] PCI: Using configuration type 1 for base access
[ 0.659222] ACPI: EC: Look up EC in DSDT
[ 0.667420] ACPI: Interpreter enabled
[ 0.667434] ACPI: (supports S0 S1 S4 S5)
[ 0.667472] ACPI: Using IOAPIC for interrupt routing
[ 0.675271] ACPI: No dock devices found.
[ 0.675312] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.675417] pci 0000:00:00.0: reg 10 32bit mmio: [0xe8000000-0xebffffff]
[ 0.675509] pci 0000:00:01.0: supports D1
[ 0.675554] pci 0000:00:08.0: reg 10 io port: [0xd000-0xd01f]
[ 0.675596] pci 0000:00:08.0: supports D1 D2
[ 0.675632] pci 0000:00:08.1: reg 10 io port: [0xd400-0xd407]
[ 0.675674] pci 0000:00:08.1: supports D1 D2
[ 0.675749] pci 0000:00:10.0: reg 20 io port: [0xd800-0xd81f]
[ 0.675771] pci 0000:00:10.0: supports D1 D2
[ 0.675774] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.675779] pci 0000:00:10.0: PME# disabled
[ 0.675837] pci 0000:00:10.1: reg 20 io port: [0xdc00-0xdc1f]
[ 0.675859] pci 0000:00:10.1: supports D1 D2
[ 0.675861] pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.675866] pci 0000:00:10.1: PME# disabled
[ 0.675924] pci 0000:00:10.2: reg 20 io port: [0xe000-0xe01f]
[ 0.675945] pci 0000:00:10.2: supports D1 D2
[ 0.675948] pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.675953] pci 0000:00:10.2: PME# disabled
[ 0.676035] pci 0000:00:10.3: reg 10 32bit mmio: [0xee000000-0xee0000ff]
[ 0.676079] pci 0000:00:10.3: supports D1 D2
[ 0.676082] pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.676087] pci 0000:00:10.3: PME# disabled
[ 0.676165] HPET not enabled in BIOS. You might try hpet=force boot option
[ 0.676176] pci 0000:00:11.0: quirk: region 0400-047f claimed by vt8235 PM
[ 0.676180] pci 0000:00:11.0: quirk: region 0500-050f claimed by vt8235 SMB
[ 0.676246] pci 0000:00:11.1: reg 20 io port: [0xe400-0xe40f]
[ 0.676313] pci 0000:00:12.0: reg 10 io port: [0xe800-0xe8ff]
[ 0.676321] pci 0000:00:12.0: reg 14 32bit mmio: [0xee001000-0xee0010ff]
[ 0.676359] pci 0000:00:12.0: supports D1 D2
[ 0.676361] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.676366] pci 0000:00:12.0: PME# disabled
[ 0.676429] pci 0000:01:00.0: reg 10 32bit mmio: [0xec000000-0xecffffff]
[ 0.676436] pci 0000:01:00.0: reg 14 32bit mmio: [0xe0000000-0xe7ffffff]
[ 0.676460] pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x00ffff]
[ 0.676516] pci 0000:00:01.0: bridge 32bit mmio: [0xec000000-0xedffffff]
[ 0.676522] pci 0000:00:01.0: bridge 32bit mmio pref: [0xe0000000-0xe7ffffff]
[ 0.676532] bus 00 -> node 0
[ 0.676552] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.709267] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
[ 0.709592] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[ 0.709912] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[ 0.710231] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
[ 0.710544] ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0
[ 0.710856] ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0
[ 0.711197] ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0
[ 0.711511] ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0
[ 0.711843] ACPI: WMI: Mapper loaded
[ 0.712405] SCSI subsystem initialized
[ 0.712612] libata version 3.00 loaded.
[ 0.712793] usbcore: registered new interface driver usbfs
[ 0.712843] usbcore: registered new interface driver hub
[ 0.712978] usbcore: registered new device driver usb
[ 0.713413] PCI: Using ACPI for IRQ routing
[ 0.713616] Bluetooth: Core ver 2.13
[ 0.713616] NET: Registered protocol family 31
[ 0.713616] Bluetooth: HCI device and connection manager initialized
[ 0.713616] Bluetooth: HCI socket layer initialized
[ 0.713616] NET: Registered protocol family 8
[ 0.713616] NET: Registered protocol family 20
[ 0.713616] NetLabel: Initializing
[ 0.713616] NetLabel: domain hash size = 128
[ 0.713616] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.713616] NetLabel: unlabeled traffic allowed by default
[ 0.713616] AppArmor: AppArmor Filesystem Enabled
[ 0.713616] pnp: PnP ACPI init
[ 0.713616] ACPI: bus type pnp registered
[ 0.720330] pnp: PnP ACPI: found 12 devices
[ 0.720338] ACPI: ACPI bus type pnp unregistered
[ 0.720346] PnPBIOS: Disabled by ACPI PNP
[ 0.720380] system 00:00: iomem range 0xd0000-0xd3fff has been reserved
[ 0.720384] system 00:00: iomem range 0xf0000-0xf7fff could not be reserved
[ 0.720388] system 00:00: iomem range 0xf8000-0xfbfff could not be reserved
[ 0.720391] system 00:00: iomem range 0xfc000-0xfffff could not be reserved
[ 0.720394] system 00:00: iomem range 0x7fff0000-0x7fffffff could not be reserved
[ 0.720399] system 00:00: iomem range 0xffff0000-0xffffffff has been reserved
[ 0.720402] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 0.720405] system 00:00: iomem range 0x100000-0x7ffeffff could not be reserved
[ 0.720409] system 00:00: iomem range 0xfec00000-0xfecfffff has been reserved
[ 0.720412] system 00:00: iomem range 0xfee00000-0xfeefffff has been reserved
[ 0.720416] system 00:00: iomem range 0xfff80000-0xfffeffff has been reserved
[ 0.720430] system 00:02: ioport range 0x400-0x47f has been reserved
[ 0.720433] system 00:02: ioport range 0x500-0x50f has been reserved
[ 0.720443] system 00:03: ioport range 0x4d0-0x4d1 has been reserved
[ 0.720446] system 00:03: ioport range 0x800-0x805 has been reserved
[ 0.720449] system 00:03: ioport range 0x290-0x297 has been reserved
[ 0.755367] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.755372] pci 0000:00:01.0: IO window: disabled
[ 0.755380] pci 0000:00:01.0: MEM window: 0xec000000-0xedffffff
[ 0.755385] pci 0000:00:01.0: PREFETCH window: 0x000000e0000000-0x000000e7ffffff
[ 0.755405] pci 0000:00:01.0: setting latency timer to 64
[ 0.755411] bus: 00 index 0 io port: [0x00-0xffff]
[ 0.755414] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[ 0.755417] bus: 01 index 0 mmio: [0x0-0x0]
[ 0.755419] bus: 01 index 1 mmio: [0xec000000-0xedffffff]
[ 0.755422] bus: 01 index 2 mmio: [0xe0000000-0xe7ffffff]
[ 0.755424] bus: 01 index 3 mmio: [0x0-0x0]
[ 0.755448] NET: Registered protocol family 2
[ 0.755715] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.756439] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.758394] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.759416] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.759422] TCP reno registered
[ 0.759756] NET: Registered protocol family 1
[ 0.760045] checking if image is initramfs... it is
[ 1.256061] Switched to high resolution mode on CPU 0
[ 1.561788] Freeing initrd memory: 7386k freed
[ 1.561933] cpufreq: No nForce2 chipset.
[ 1.562237] audit: initializing netlink socket (disabled)
[ 1.562277] type=2000 audit(1256040118.560:1): initialized
[ 1.570429] highmem bounce pool size: 64 pages
[ 1.570447] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.572352] VFS: Disk quotas dquot_6.5.1
[ 1.572499] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.573964] fuse init (API version 7.10)
[ 1.574190] msgmni has been set to 1698
[ 1.574761] alg: No test for stdrng (krng)
[ 1.574826] io scheduler noop registered
[ 1.574831] io scheduler anticipatory registered
[ 1.574834] io scheduler deadline registered
[ 1.574904] io scheduler cfq registered (default)
[ 1.574927] PCI: VIA PCI bridge detected.Disabling DAC.
[ 1.575045] pci 0000:01:00.0: Boot video device
[ 1.580402] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.580422] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.580721] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 1.580728] ACPI: Power Button (FF) [PWRF]
[ 1.580823] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 1.580828] ACPI: Power Button (CM) [PWRB]
[ 1.580947] fan PNP0C0B:00: registered as cooling_device0
[ 1.580959] ACPI: Fan [FAN] (on)
[ 1.581423] processor ACPI_CPU:00: registered as cooling_device1
[ 1.585416] thermal LNXTHERM:01: registered as thermal_zone0
[ 1.585871] ACPI: Thermal Zone [THRM] (30 C)
[ 1.586014] isapnp: Scanning for PnP cards...
[ 1.940159] isapnp: No Plug & Play device found
[ 1.942646] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 1.942824] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.943453] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.945265] brd: module loaded
[ 1.946208] loop: module loaded
[ 1.946443] Fixed MDIO Bus: probed
[ 1.946457] PPP generic driver version 2.4.2
[ 1.946608] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 1.946704] Driver 'sd' needs updating - please use bus_type methods
[ 1.946743] Driver 'sr' needs updating - please use bus_type methods
[ 1.947702] pata_via 0000:00:11.1: version 0.3.3
[ 1.948298] ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
[ 1.948306] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
[ 1.948323] pata_via 0000:00:11.1: PCI INT A -> Link[ALKA] -> GSI 20 (level, low) -> IRQ 20
[ 1.948735] scsi0 : pata_via
[ 1.949032] scsi1 : pata_via
[ 1.952841] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xe400 irq 14
[ 1.952848] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xe408 irq 15
[ 2.124431] ata1.01: ATAPI: HL-DT-STDVD-ROM GDR8163B, 0L23, max UDMA/33
[ 2.140317] ata1.01: configured for UDMA/33
[ 2.313559] ata2.01: ATA-5: WDC WD200EB-00BHF0, 15.15M15, max UDMA/100
[ 2.313565] ata2.01: 39102336 sectors, multi 16: LBA
[ 2.329405] ata2.01: configured for UDMA/100
[ 2.337877] scsi 0:0:1:0: CD-ROM HL-DT-ST DVD-ROM GDR8163B 0L23 PQ: 0 ANSI: 5
[ 2.345393] sr0: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
[ 2.345404] Uniform CD-ROM driver Revision: 3.20
[ 2.345656] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 2.345810] sr 0:0:1:0: Attached scsi generic sg0 type 5
[ 2.346089] scsi 1:0:1:0: Direct-Access ATA WDC WD200EB-00BH 15.1 PQ: 0 ANSI: 5
[ 2.346420] sd 1:0:1:0: [sda] 39102336 512-byte hardware sectors: (20.0 GB/18.6 GiB)
[ 2.346492] sd 1:0:1:0: [sda] Write Protect is off
[ 2.346497] sd 1:0:1:0: [sda] Mode Sense: 00 3a 00 00
[ 2.346621] sd 1:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.346873] sd 1:0:1:0: [sda] 39102336 512-byte hardware sectors: (20.0 GB/18.6 GiB)
[ 2.346944] sd 1:0:1:0: [sda] Write Protect is off
[ 2.346948] sd 1:0:1:0: [sda] Mode Sense: 00 3a 00 00
[ 2.347064] sd 1:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.347077] sda: sda1 sda2 < sda5 >
[ 2.400411] sd 1:0:1:0: [sda] Attached SCSI disk
[ 2.400543] sd 1:0:1:0: Attached scsi generic sg1 type 0
[ 2.400927] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.401435] ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using IRQ 21
[ 2.401442] ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
[ 2.401458] ehci_hcd 0000:00:10.3: PCI INT D -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 2.401509] ehci_hcd 0000:00:10.3: EHCI Host Controller
[ 2.401745] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
[ 2.401860] ehci_hcd 0000:00:10.3: irq 21, io mem 0xee000000
[ 2.412038] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00
[ 2.412237] usb usb1: configuration #1 chosen from 1 choice
[ 2.412305] hub 1-0:1.0: USB hub found
[ 2.412334] hub 1-0:1.0: 6 ports detected
[ 2.412651] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.412708] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.412838] uhci_hcd 0000:00:10.0: PCI INT A -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 2.412858] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 2.413014] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 2.413056] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000d800
[ 2.413353] usb usb2: configuration #1 chosen from 1 choice
[ 2.413419] hub 2-0:1.0: USB hub found
[ 2.413451] hub 2-0:1.0: 2 ports detected
[ 2.413738] uhci_hcd 0000:00:10.1: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 2.413758] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 2.413907] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 2.413949] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000dc00
[ 2.414160] usb usb3: configuration #1 chosen from 1 choice
[ 2.414239] hub 3-0:1.0: USB hub found
[ 2.414267] hub 3-0:1.0: 2 ports detected
[ 2.414544] uhci_hcd 0000:00:10.2: PCI INT C -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 2.414563] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 2.414713] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[ 2.414754] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000e000
[ 2.414982] usb usb4: configuration #1 chosen from 1 choice
[ 2.415058] hub 4-0:1.0: USB hub found
[ 2.415084] hub 4-0:1.0: 2 ports detected
[ 2.415449] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 2.415456] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 2.415648] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.416073] mice: PS/2 mouse device common for all mice
[ 2.416576] rtc_cmos 00:05: RTC can wake from S4
[ 2.416687] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 2.416750] rtc0: alarms up to one year, y3k, 242 bytes nvram
[ 2.416931] device-mapper: uevent: version 1.0.3
[ 2.417347] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 2.417593] device-mapper: multipath: version 1.0.5 loaded
[ 2.417603] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 2.417940] EISA: Probing bus 0 at eisa.0
[ 2.417996] EISA: Detected 0 cards.
[ 2.418129] cpuidle: using governor ladder
[ 2.418135] cpuidle: using governor menu
[ 2.419081] TCP cubic registered
[ 2.419309] NET: Registered protocol family 10
[ 2.420217] lo: Disabled Privacy Extensions
[ 2.420691] NET: Registered protocol family 17
[ 2.420773] Bluetooth: L2CAP ver 2.11
[ 2.420776] Bluetooth: L2CAP socket layer initialized
[ 2.420780] Bluetooth: SCO (Voice Link) ver 0.6
[ 2.420782] Bluetooth: SCO socket layer initialized
[ 2.420929] Bluetooth: RFCOMM socket layer initialized
[ 2.420953] Bluetooth: RFCOMM TTY layer initialized
[ 2.420957] Bluetooth: RFCOMM ver 1.10
[ 2.421097] Using IPI No-Shortcut mode
[ 2.421423] registered taskstats version 1
[ 2.421599] Magic number: 13:759:26
[ 2.421748] rtc_cmos 00:05: setting system clock to 2009-10-20 12:01:59 UTC (1256040119)
[ 2.421756] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.421758] EDD information not available.
[ 2.422864] Freeing unused kernel memory: 532k freed
[ 2.423032] Write protecting the kernel text: 4120k
[ 2.423078] Write protecting the kernel read-only data: 1524k
[ 2.440884] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 2.780077] usb 1-5: new high speed USB device using ehci_hcd and address 3
[ 2.919280] usb 1-5: configuration #1 chosen from 1 choice
[ 3.088733] Floppy drive(s): fd0 is 1.44M
[ 3.109739] FDC 0 is a post-1991 82077
[ 3.164056] usb 2-1: new low speed USB device using uhci_hcd and address 2
[ 3.341512] usb 2-1: configuration #1 chosen from 1 choice
[ 3.405247] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 3.405259] via-rhine: Broken BIOS detected, avoid_D3 enabled.
[ 3.405810] ACPI: PCI Interrupt Link [ALKD] BIOS reported IRQ 0, using IRQ 23
[ 3.405818] ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
[ 3.405837] via-rhine 0000:00:12.0: PCI INT A -> Link[ALKD] -> GSI 23 (level, low) -> IRQ 23
[ 3.407009] eth0: VIA Rhine II at 0xee001000, 00:30:18:a1:19:5a, IRQ 23.
[ 3.407725] eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
[ 4.255319] usbcore: registered new interface driver hiddev
[ 4.271776] input: Microsoft Comfort Optical Mouse 1000 as /devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.0/input/input4
[ 4.275167] generic-usb 0003:045E:00F6.0001: input,hidraw0: USB HID v1.11 Mouse [Microsoft Comfort Optical Mouse 1000] on usb-0000:00:10.0-1/input0
[ 4.275230] usbcore: registered new interface driver usbhid
[ 4.275237] usbhid: v2.6:USB HID core driver
[ 4.383823] PM: Starting manual resume from disk
[ 4.383831] PM: Resume from partition 8:5
[ 4.383834] PM: Checking hibernation image.
[ 4.384156] PM: Resume from disk failed.
[ 4.440869] kjournald starting. Commit interval 5 seconds
[ 4.440908] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.159877] udev: starting version 141
[ 13.606526] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 13.631017] Linux agpgart interface v0.103
[ 13.712761] agpgart: Detected VIA P4M266x/P4N266 chipset
[ 13.729971] parport_pc 00:0a: reported by Plug and Play ACPI
[ 13.730032] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 13.732282] agpgart-via 0000:00:00.0: AGP aperture is 64M @ 0xe8000000
[ 13.815892] gameport: EMU10K1 is pci0000:00:08.1/gameport0, io 0xd400, speed 1084kHz
[ 14.020286] cfg80211: Calling CRDA to update world regulatory domain
[ 14.115498] irda_init()
[ 14.115535] NET: Registered protocol family 23
[ 15.030115] EMU10K1_Audigy 0000:00:08.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 15.232229] rtl8187: 8187B chip detected. Support is EXPERIMENTAL, and could damage your
[ 15.232235] hardware, use at your own risk
[ 15.238947] phy0: Selected rate control algorithm 'pid'
[ 15.337473] phy0: hwaddr 00:1b:2f:c6:bb:6e, RTL8187BvE V0 + rtl8225z2
[ 15.337565] usbcore: registered new interface driver rtl8187
[ 15.698775] ppdev: user-space parallel port driver
[ 15.871625] cfg80211: World regulatory domain updated:
[ 15.871638] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.871642] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.871645] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.871648] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.871651] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.871654] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 16.001345] udev: renamed network interface wlan0 to wlan2
[ 16.311407] lp0: using parport0 (interrupt-driven).
[ 16.595414] Adding 859436k swap on /dev/sda5. Priority:-1 extents:1 across:859436k
[ 115.080083] EXT3 FS on sda1, internal journal
[ 116.689751] type=1505 audit(1256040233.766:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2745
[ 116.788394] type=1505 audit(1256040233.866:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2749
[ 116.788892] type=1505 audit(1256040233.866:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2749
[ 116.789214] type=1505 audit(1256040233.866:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2749
[ 116.789517] type=1505 audit(1256040233.866:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2749
[ 117.034734] type=1505 audit(1256040234.110:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2754
[ 117.035468] type=1505 audit(1256040234.110:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2754
[ 117.099307] type=1505 audit(1256040234.174:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2758
[ 121.463992] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 121.464050] Bluetooth: BNEP filters: protocol multicast
[ 121.485861] Bridge firewalling registered
[ 126.925957] eth0: link down
[ 126.926225] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 142.941649] ADDRCONF(NETDEV_UP): wlan2: link is not ready
[ 182.545405] wlan2: authenticate with AP 00:1c:a2:ac:df:9d
[ 182.547690] wlan2: authenticated
[ 182.547702] wlan2: associate with AP 00:1c:a2:ac:df:9d
[ 182.555443] wlan2: RX AssocResp from 00:1c:a2:ac:df:9d (capab=0x471 status=0 aid=2)
[ 182.555452] wlan2: associated
[ 182.571071] ADDRCONF(NETDEV_CHANGE): wlan2: l

[logari81]

χωρις την δευτερη καρτα έχουνε φύγει τα παραξενα σφαλματα που εδειχνε το dmesg. Για να μην το παιδεύουμε όμως πολύ, θα σου προτεινα να δοκιμασεις το LiveCD της προσωρινής εκδοσης του 9.10
http://cdimage.ubuntu.com/daily-live/current/
αν δουλεύει εκει καλα, τοτε περιμενε απλως καμια 10αρια μερες για να κανεις το upgrade.