Πρόβλημα με κάρτα broadcom

[logari81]

δοκιμασε λιγο να κλεισεις και να ανοιξεις τον οδηγο με

Κώδικας: Επιλογή όλων

sudo rmmod b43legacy
sudo modprobe b43legacy

επισης συγκρινε το αποτελεσμα του

Κώδικας: Επιλογή όλων

rfkill list

πριν και μετα το πατημα του διακοπτη.

[logari81]

Το προβλημα αυτο φαινεται οτι απασχολει πολυ κοσμο.

καμια σχεση, τα ποστ που εχεις βρει ειναι ασχετα, ολες οι καρτες που αναφερονται σε αυτα τα ποστ και γενικα ολες οι καρτες broadcom λειτουργουν μετα τηνε ενεργοποιηση του firmware στο Hardware Drivers. Η δική σου περίπτωση ειναι εξαίρεση κι αφορα μονο την καρτα σου με κωδικο 4301 και μαλλον αφορα μονο το Ubuntu 9.10. Ειναι μαλλον καποιο πολυ εξειδικευμενο προβλημα.

[2010]

δοκιμασε λιγο να κλεισεις και να ανοιξεις τον οδηγο με

Κώδικας: Επιλογή όλων

sudo rmmod b43legacy
sudo modprobe b43legacy

επισης συγκρινε το αποτελεσμα του

Κώδικας: Επιλογή όλων

rfkill list

πριν και μετα το πατημα του διακοπτη.

Κώδικας: Επιλογή όλων

ms@abc:~$ sudo rmmod b43legacy
[sudo] password for ms:
ms@abc:~$ rfkill list
ms@abc:~$ sudo modprobe b43legacy
ms@abc:~$ rfkill list
3: phy3: Wireless LAN
Soft blocked: no
Hard blocked: no
ms@abc:~$ ^C


Οταν παταω sudo rmmod b43legacy εξαφανιζεται η ενδειξη "Wireless Networks" στο εικονιδιο πανω δεξια.
Οταν παταω sudo modprobe b43legacy εμφανιζεται η ενδειξη "Wireless Networks" στο εικονιδιο πανω δεξια αλλα ακριβως κατω απο αυτη την ενδειξη λεει: device is not ready.

Τι πρεπει να κανουμε για να φτιαξουμε το device;

Σε καμια περιπτωση δεν αναψε το λαμπακι του διακοπτη wireless και σε καμια περιπτωση δεν μπορεσα να συνδεθω στο δικτυο ασυρματα.
Το rfkill list δεν επηρεαζεται απο τα πατηματα του διακοπτη. Εξαρταται μονο απο τις δυο εντολες.

[logari81]

για δωσε και το αποτελεσμα της εντολής

Κώδικας: Επιλογή όλων

ls /lib/firmware

και εχε λιγο υπομονη

[logari81]

[ 32.261550] b43legacy ssb0:0: firmware: requesting b43legacy/ucode2.fw
[ 32.355711] b43legacy-phy0 ERROR: Firmware file "b43legacy/ucode2.fw" not found or load failed.

κατσε γιατι μου φαινεται σε παιδευω τζαμπα. Αποτι φαινεται εδω, τωρα μετα την επανεγκατασταση οντως δεν βρισκει το firmware. Ποσταρε το αποτελεσμα που σου ζητησα πριν, και το αποτελεσμα του:

Κώδικας: Επιλογή όλων

ls /lib/firmware/b43legacy

Επισης ποσταρε μου ενα screenshot του System--Administration--Hardware Drivers όπως ειναι τωρα και μετα απο αυτο θα σου δωσω επιπλεον οδηγιες.

Συγνωμη που θα σε καθυστερησω λιγο αλλα με ενδιαφερει περισσοτερο να λυσουμε το προβλημα μονιμως στο Ubuntu παρα να λύσουμε μονο το δικο σου προβλημα.

[2010]

Oριστε τα ls /lb/firmware και ls /lib/firmware/b43legacy:

Κώδικας: Επιλογή όλων

ms@abc:~$ ls /lib/firmware
2.6.31-14-generic isl3886usb
acx isl3887usb
aic94xx-seq.fw isl3890
ar9170-1.fw iwlwifi-1000-3.ucode
ar9170-2.fw iwlwifi-3945-1.ucode
ar9170.fw iwlwifi-3945-2.ucode
atmel_at76c502_3com.bin iwlwifi-4965-1.ucode
atmel_at76c502_3com-wpa.bin iwlwifi-4965-2.ucode
atmel_at76c502.bin iwlwifi-5000-1.ucode
atmel_at76c502d.bin iwlwifi-5000-2.ucode
atmel_at76c502d-wpa.bin iwlwifi-5150-2.ucode
atmel_at76c502e.bin iwlwifi-6000-4.ucode
atmel_at76c502e-wpa.bin lbtf_usb.bin
atmel_at76c502-wpa.bin NPE-B
atmel_at76c503-i3861.bin NPE-B.01020201
atmel_at76c503-i3863.bin NPE-C
atmel_at76c503-rfmd-0.90.2-140.bin NPE-C.02020201
atmel_at76c503-rfmd-acc.bin ql2100_fw.bin
atmel_at76c503-rfmd.bin ql2200_fw.bin
atmel_at76c504_2958-wpa.bin ql2300_fw.bin
atmel_at76c504a_2958-wpa.bin ql2322_fw.bin
atmel_at76c504.bin ql2400_fw.bin
atmel_at76c504c-wpa.bin rt2561.bin
atmel_at76c505a-rfmd2958.bin rt2561s.bin
atmel_at76c505-rfmd2958.bin rt2661.bin
atmel_at76c505-rfmd.bin rt2860.bin
atmel_at76c506.bin rt2870.bin
atmel_at76c506-wpa.bin rt73.bin
BCM2033-FW.BIN v4l-cx23418-apu.fw
BCM2033-MD.BIN v4l-cx23418-cpu.fw
dvb-fe-xc5000-1.6.114.fw v4l-cx23418-dig.fw
dvb-usb-dib0700-1.20.fw v4l-cx2341x-dec.fw
i2400m-fw-usb-1.3.sbcf v4l-cx2341x-enc.fw
i2400m-fw-usb-1.4.sbcf v4l-cx2341x-init.mpg
ipw2100-1.3.fw v4l-cx23885-avcore-01.fw
ipw2100-1.3-i.fw v4l-cx23885-enc.fw
ipw2100-1.3-p.fw v4l-cx25840.fw
ipw2200-bss.fw v4l-pvrusb2-24xxx-01.fw
ipw2200-ibss.fw v4l-pvrusb2-29xxx-01.fw
ipw2200-sniffer.fw zd1201-ap.fw
isl3877 zd1201.fw
isl3886pci zd1211
ms@abc:~$ ls /lib/firmware/b43legacy
ls: cannot access /lib/firmware/b43legacy: No such file or directory
ms@abc:~$


O φακελος b43legacy δεν υπαρχει αυτη τη στιγμη.

Kαι το screenshot αυτη τη στιγμη:

[logari81]

Κανε activate εκει που λεει Broadcom B43 wireless driver και μετα ξαναδώσε μας το αποτελεσμα της εντολης

Κώδικας: Επιλογή όλων

ls /lib/firmware/b43legacy

[2010]

Κανε activate εκει που λεει Broadcom B43 wireless driver και μετα ξαναδώσε μας το αποτελεσμα της εντολης

Κώδικας: Επιλογή όλων

ls /lib/firmware/b43legacy

Κώδικας: Επιλογή όλων

ms@abc:~$ ls /lib/firmware/b43legacy
a0g0bsinitvals2.fw a0g1bsinitvals5.fw b0g0initvals2.fw ucode11.fw
a0g0bsinitvals5.fw a0g1initvals5.fw b0g0initvals5.fw ucode2.fw
a0g0initvals2.fw b0g0bsinitvals2.fw pcm4.fw ucode4.fw
a0g0initvals5.fw b0g0bsinitvals5.fw pcm5.fw ucode5.fw

[logari81]

ωραια τώρα δοκιμασε παλι το rfkill list πριν και μετα το πατημα του διακοπτη, επισης δοκιμασε της εντολες με το rmmod και το modrope που δοκιμασες πριν και μετα απο αυτα τρεξε

Κώδικας: Επιλογή όλων

dmesg

παλι και δωσε ολα τα αποτελεσματα.

[2010]

Tο πατημα του κουμπιου δεν ειχε καμια επιπτωση και το rfkill list δεν εβγαζε τιποτα, ειτε ηταν πατημενος ο διακοπτης ειτε οχι (το λαμπακι του δεν αναβε και δεν μπορουσα να συνδεθω στο ιντερνετ).

Οταν παταω sudo rmmod b43legacy εξαφανιζεται η ενδειξη "Wireless Networks" στο εικονιδιο πανω δεξια.
Οταν παταω sudo modprobe b43legacy εμφανιζεται η ενδειξη "Wireless Networks" στο εικονιδιο πανω δεξια ενω ακριβως κατω απο αυτη την ενδειξη λεει: "wireless is disabled".

Πριν εγκαταστησουμε αυτο το firmware στο ιδιο σημειο εγραφε: "device is not ready".

Oσον αφορα την εντολη rfkill list εχουμε μια διαφοροποιηση του "Hard blocked" απο no πριν την εγκατασταση του firmware σε yes μετα την εγκατασταση.

1: phy1: Wireless LAN
Soft blocked: no
Hard blocked: yes
Πριν εγκαταστησουμε αυτο το firmware εγραφε:
Soft blocked: no
Hard blocked: no

Κώδικας: Επιλογή όλων

ms@abc:~$ sudo rmmod b43legacy
[sudo] password for ms:
ms@abc:~$ rfkill list
ms@abc:~$ sudo modprobe b43legacy
ms@abc:~$ rfkill list
1: phy1: Wireless LAN
Soft blocked: no
Hard blocked: yes
ms@abc:~$ dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.31-14-generic (buildd@rothera) (gcc version 4.4.1 (Ubuntu 4.4.1-4ubuntu8) ) #48-Ubuntu SMP Fri Oct 16 14:04:26 UTC 2009 (Ubuntu 2.6.31-14.48-generic)
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000000bf70000 (usable)
[ 0.000000] BIOS-e820: 000000000bf70000 - 000000000bf7d000 (ACPI data)
[ 0.000000] BIOS-e820: 000000000bf7d000 - 000000000bf80000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000000bf80000 - 000000000c000000 (reserved)
[ 0.000000] BIOS-e820: 000000001bf80000 - 000000001c000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] DMI present.
[ 0.000000] last_pfn = 0xbf70 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-DFFFF uncachable
[ 0.000000] E0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask FF8000000 write-back
[ 0.000000] 1 base 008000000 mask FFC000000 write-back
[ 0.000000] 2 base 00BF80000 mask FFFF80000 uncachable
[ 0.000000] 3 base 01BF80000 mask FFFF80000 uncachable
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820 update range: 0000000000002000 - 0000000000006000 (usable) ==> (reserved)
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000002000 (usable)
[ 0.000000] modified: 0000000000002000 - 0000000000006000 (reserved)
[ 0.000000] modified: 0000000000006000 - 000000000009f800 (usable)
[ 0.000000] modified: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000d0000 - 00000000000d8000 (reserved)
[ 0.000000] modified: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 000000000bf70000 (usable)
[ 0.000000] modified: 000000000bf70000 - 000000000bf7d000 (ACPI data)
[ 0.000000] modified: 000000000bf7d000 - 000000000bf80000 (ACPI NVS)
[ 0.000000] modified: 000000000bf80000 - 000000000c000000 (reserved)
[ 0.000000] modified: 000000001bf80000 - 000000001c000000 (reserved)
[ 0.000000] modified: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] modified: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] modified: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] initial memory mapped : 0 - 00c00000
[ 0.000000] init_memory_mapping: 0000000000000000-000000000bf70000
[ 0.000000] Using x86 segment limits to approximate NX protection
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 000bc00000 page 2M
[ 0.000000] 000bc00000 - 000bf70000 page 4k
[ 0.000000] kernel direct mapping tables up to bf70000 @ 7000-c000
[ 0.000000] RAMDISK: 08889000 - 08fd339c
[ 0.000000] ACPI: RSDP 000f66a0 00014 (v00 PTLTD )
[ 0.000000] ACPI: RSDT 0bf79269 0002C (v01 PTLTD RSDT 06040000 LTP 00000000)
[ 0.000000] ACPI: FACP 0bf7cf32 00074 (v01 HP Chinook 06040000 ATI 000F4240)
[ 0.000000] ACPI: DSDT 0bf79295 03C9D (v01 HP SB200 06040000 INTL 20030509)
[ 0.000000] ACPI: FACS 0bf7ffc0 00040
[ 0.000000] ACPI: APIC 0bf7cfa6 0005A (v01 PTLTD APIC 06040000 LTP 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 191MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 0bf70000
[ 0.000000] low ram: 0 - 0bf70000
[ 0.000000] node 0 low ram: 00000000 - 0bf70000
[ 0.000000] node 0 bootmap 00008000 - 000097f0
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 000bf70000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0000100000 - 00008a80a0] TEXT DATA BSS ==> [0000100000 - 00008a80a0]
[ 0.000000] #4 [0008889000 - 0008fd339c] RAMDISK ==> [0008889000 - 0008fd339c]
[ 0.000000] #5 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
[ 0.000000] #6 [00008a9000 - 00008ac150] BRK ==> [00008a9000 - 00008ac150]
[ 0.000000] #7 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
[ 0.000000] #8 [0000008000 - 000000a000] BOOTMAP ==> [0000008000 - 000000a000]
[ 0.000000] found SMP MP-table at [c00f6610] f6610
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x0000bf70
[ 0.000000] HighMem 0x0000bf70 -> 0x0000bf70
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00000002
[ 0.000000] 0: 0x00000006 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0000bf70
[ 0.000000] On node 0 totalpages: 48907
[ 0.000000] free_area_init_node: node 0, pgdat c0784900, node_mem_map c1000000
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3963 pages, LIFO batch:0
[ 0.000000] Normal zone: 351 pages used for memmap
[ 0.000000] Normal zone: 44561 pages, LIFO batch:7
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x8008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 0000000000002000 - 0000000000006000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d0000
[ 0.000000] PM: Registered nosave memory: 00000000000d0000 - 00000000000d8000
[ 0.000000] PM: Registered nosave memory: 00000000000d8000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 1c000000 (gap: 1c000000:e2c00000)
[ 0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages at c1182000, static data 35612 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 48524
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.31-14-generic root=UUID=823bc237-883d-404b-af1b-879c3b890f14 ro quiet splash
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 980160 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
[ 0.000000] Memory: 177356k/196032k available (4565k kernel code, 18120k reserved, 2143k data, 540k init, 0k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff1d000 - 0xfffff000 ( 904 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xcc770000 - 0xff7fe000 ( 816 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xcbf70000 ( 191 MB)
[ 0.000000] .init : 0xc078e000 - 0xc0815000 ( 540 kB)
[ 0.000000] .data : 0xc0575554 - 0xc078d308 (2143 kB)
[ 0.000000] .text : 0xc0100000 - 0xc0575554 (4565 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:2304 nr_irqs:256
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2800.480 MHz processor.
[ 0.001118] Console: colour VGA+ 80x25
[ 0.001126] console [tty0] enabled
[ 0.001188] Calibrating delay loop (skipped), value calculated using timer frequency.. 5600.96 BogoMIPS (lpj=11201920)
[ 0.001220] Security Framework initialized
[ 0.001258] AppArmor: AppArmor initialized
[ 0.001276] Mount-cache hash table entries: 512
[ 0.001514] Initializing cgroup subsys ns
[ 0.001527] Initializing cgroup subsys cpuacct
[ 0.001534] Initializing cgroup subsys memory
[ 0.001549] Initializing cgroup subsys freezer
[ 0.001555] Initializing cgroup subsys net_cls
[ 0.001587] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 0.001594] CPU: L2 cache: 128K
[ 0.001599] CPU: Hyper-Threading is disabled
[ 0.001606] mce: CPU supports 4 MCE banks
[ 0.001622] CPU0: Thermal monitoring enabled (TM1)
[ 0.001643] Performance Counters: no PMU driver, software counters only.
[ 0.001656] Checking 'hlt' instruction... OK.
[ 0.017056] SMP alternatives: switching to UP code
[ 0.027479] Freeing SMP alternatives: 19k freed
[ 0.027516] ACPI: Core revision 20090521
[ 0.040253] alloc irq_desc for 21 on node 0
[ 0.040258] alloc kstat_irqs on node 0
[ 0.040394] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.048001] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
[ 0.048001] ...trying to set up timer (IRQ0) through the 8259A ...
[ 0.048001] ..... (found apic 0 pin 2) ...
[ 0.091517] ....... works.
[ 0.091521] CPU0: Intel(R) Celeron(R) CPU 2.80GHz stepping 09
[ 0.092001] Brought up 1 CPUs
[ 0.092001] Total of 1 processors activated (5600.96 BogoMIPS).
[ 0.092001] CPU0 attaching NULL sched-domain.
[ 0.092001] Booting paravirtualized kernel on bare hardware
[ 0.092001] regulator: core version 0.5
[ 0.092001] Time: 14:28:30 Date: 12/16/09
[ 0.092001] NET: Registered protocol family 16
[ 0.092001] EISA bus registered
[ 0.092001] ACPI: bus type pci registered
[ 0.092001] PCI: PCI BIOS revision 2.10 entry at 0xfd968, last bus=2
[ 0.092001] PCI: Using configuration type 1 for base access
[ 0.092352] bio: create slab <bio-0> at 0
[ 0.093272] ACPI: EC: Look up EC in DSDT
[ 0.101096] ACPI: Interpreter enabled
[ 0.101112] ACPI: (supports S0 S3 S4 S5)
[ 0.101147] ACPI: BIOS offers _GTS
[ 0.101150] ACPI: If "acpi.gts=1" improves suspend, please notify linux-acpi@vger.kernel.org
[ 0.101156] ACPI: Using IOAPIC for interrupt routing
[ 0.105584] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 0.164342] ACPI: EC: GPE = 0x6, I/O: command/status = 0x66, data = 0x62
[ 0.164348] ACPI: EC: driver started in interrupt mode
[ 0.164643] ACPI: No dock devices found.
[ 0.165971] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.166077] pci 0000:00:00.0: reg 10 32bit mmio: [0xea000000-0xebffffff]
[ 0.166088] pci 0000:00:00.0: reg 14 32bit mmio: [0xe8000000-0xe8000fff]
[ 0.166186] pci 0000:00:13.0: reg 10 32bit mmio: [0xe8001000-0xe8001fff]
[ 0.166238] pci 0000:00:13.1: reg 10 32bit mmio: [0xe8002000-0xe8002fff]
[ 0.166294] pci 0000:00:14.0: reg 10 io port: [0x8040-0x804f]
[ 0.166303] pci 0000:00:14.0: reg 14 32bit mmio: [0x000000-0x0003ff]
[ 0.166349] pci 0000:00:14.1: reg 10 io port: [0x1f0-0x1f7]
[ 0.166358] pci 0000:00:14.1: reg 14 io port: [0x3f4-0x3f7]
[ 0.166367] pci 0000:00:14.1: reg 18 io port: [0x170-0x177]
[ 0.166376] pci 0000:00:14.1: reg 1c io port: [0x374-0x377]
[ 0.166385] pci 0000:00:14.1: reg 20 io port: [0x8060-0x806f]
[ 0.166498] pci 0000:00:14.5: reg 10 32bit mmio: [0xe8003000-0xe80030ff]
[ 0.166547] pci 0000:00:14.6: reg 10 32bit mmio: [0xe8003400-0xe80034ff]
[ 0.166635] pci 0000:01:05.0: reg 10 32bit mmio: [0xf0000000-0xf7ffffff]
[ 0.166645] pci 0000:01:05.0: reg 14 io port: [0x9000-0x90ff]
[ 0.166654] pci 0000:01:05.0: reg 18 32bit mmio: [0xe8100000-0xe810ffff]
[ 0.166673] pci 0000:01:05.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[ 0.166698] pci 0000:01:05.0: supports D1 D2
[ 0.166738] pci 0000:00:01.0: bridge io port: [0x9000-0x9fff]
[ 0.166744] pci 0000:00:01.0: bridge 32bit mmio: [0xe8100000-0xe81fffff]
[ 0.166752] pci 0000:00:01.0: bridge 32bit mmio pref: [0xf0000000-0xf7ffffff]
[ 0.166788] pci 0000:02:02.0: reg 10 32bit mmio: [0xe8200000-0xe8201fff]
[ 0.166863] pci 0000:02:03.0: reg 10 io port: [0xa000-0xa0ff]
[ 0.166874] pci 0000:02:03.0: reg 14 32bit mmio: [0xe8204000-0xe82040ff]
[ 0.166923] pci 0000:02:03.0: supports D1 D2
[ 0.166928] pci 0000:02:03.0: PME# supported from D1 D2 D3hot D3cold
[ 0.166935] pci 0000:02:03.0: PME# disabled
[ 0.166979] pci 0000:02:04.0: reg 10 32bit mmio: [0x000000-0x000fff]
[ 0.167004] pci 0000:02:04.0: supports D1 D2
[ 0.167008] pci 0000:02:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.167015] pci 0000:02:04.0: PME# disabled
[ 0.167066] pci 0000:02:04.1: reg 10 32bit mmio: [0x000000-0x000fff]
[ 0.167092] pci 0000:02:04.1: supports D1 D2
[ 0.167096] pci 0000:02:04.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.167103] pci 0000:02:04.1: PME# disabled
[ 0.167156] pci 0000:02:07.0: reg 10 32bit mmio: [0xe8202000-0xe8202fff]
[ 0.167209] pci 0000:02:07.0: supports D1 D2
[ 0.167213] pci 0000:02:07.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.167219] pci 0000:02:07.0: PME# disabled
[ 0.167262] pci 0000:02:07.1: reg 10 32bit mmio: [0xe8203000-0xe8203fff]
[ 0.167315] pci 0000:02:07.1: supports D1 D2
[ 0.167319] pci 0000:02:07.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.167326] pci 0000:02:07.1: PME# disabled
[ 0.167369] pci 0000:02:07.2: reg 10 32bit mmio: [0xe8204400-0xe82044ff]
[ 0.167423] pci 0000:02:07.2: supports D1 D2
[ 0.167428] pci 0000:02:07.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.167435] pci 0000:02:07.2: PME# disabled
[ 0.167485] pci 0000:00:14.4: transparent bridge
[ 0.167494] pci 0000:00:14.4: bridge io port: [0xa000-0xafff]
[ 0.167500] pci 0000:00:14.4: bridge 32bit mmio: [0xe8200000-0xe82fffff]
[ 0.167565] pci_bus 0000:00: on NUMA node 0
[ 0.167576] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.167710] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
[ 0.167826] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[ 0.171123] ACPI: PCI Interrupt Link [LNK0] (IRQs 5 10 11) *0, disabled.
[ 0.171311] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 10 11) *0, disabled.
[ 0.171491] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 10 11) *0, disabled.
[ 0.171674] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 10 11) *0, disabled.
[ 0.172102] SCSI subsystem initialized
[ 0.172285] libata version 3.00 loaded.
[ 0.172542] usbcore: registered new interface driver usbfs
[ 0.172590] usbcore: registered new interface driver hub
[ 0.172709] usbcore: registered new device driver usb
[ 0.173194] ACPI: WMI: Mapper loaded
[ 0.173201] PCI: Using ACPI for IRQ routing
[ 0.173494] Bluetooth: Core ver 2.15
[ 0.173639] NET: Registered protocol family 31
[ 0.173643] Bluetooth: HCI device and connection manager initialized
[ 0.173648] Bluetooth: HCI socket layer initialized
[ 0.173652] NetLabel: Initializing
[ 0.173655] NetLabel: domain hash size = 128
[ 0.173658] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.173691] NetLabel: unlabeled traffic allowed by default
[ 0.176692] pnp: PnP ACPI init
[ 0.176736] ACPI: bus type pnp registered
[ 0.179211] pnp 00:07: io resource (0x8000-0x8068) overlaps 0000:00:14.1 BAR 4 (0x8060-0x806f), disabling
[ 0.204032] pnp: PnP ACPI: found 10 devices
[ 0.204039] ACPI: ACPI bus type pnp unregistered
[ 0.204047] PnPBIOS: Disabled by ACPI PNP
[ 0.204084] system 00:07: ioport range 0x200-0x20f has been reserved
[ 0.204089] system 00:07: ioport range 0xc14-0xc14 has been reserved
[ 0.204094] system 00:07: ioport range 0xc50-0xc52 has been reserved
[ 0.204098] system 00:07: ioport range 0xc6c-0xc6c has been reserved
[ 0.204103] system 00:07: ioport range 0xc6f-0xc6f has been reserved
[ 0.204107] system 00:07: ioport range 0xcd6-0xcd7 has been reserved
[ 0.204112] system 00:07: ioport range 0x1080-0x1080 has been reserved
[ 0.204117] system 00:07: ioport range 0x8800-0x8800 has been reserved
[ 0.204121] system 00:07: ioport range 0xfe00-0xfe00 has been reserved
[ 0.204126] system 00:07: ioport range 0xfe10-0xfe11 has been reserved
[ 0.204132] system 00:07: iomem range 0xe4000-0xfffff could not be reserved
[ 0.204137] system 00:07: iomem range 0x100000-0xbffffff could not be reserved
[ 0.204142] system 00:07: iomem range 0xe8000000-0xe8000fff has been reserved
[ 0.204148] system 00:07: iomem range 0xfff80000-0xffffffff has been reserved
[ 0.239007] AppArmor: AppArmor Filesystem Enabled
[ 0.239074] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.239080] pci 0000:00:01.0: IO window: 0x9000-0x9fff
[ 0.239085] pci 0000:00:01.0: MEM window: 0xe8100000-0xe81fffff
[ 0.239090] pci 0000:00:01.0: PREFETCH window: 0xf0000000-0xf7ffffff
[ 0.239124] pci 0000:02:04.0: CardBus bridge, secondary bus 0000:03
[ 0.239128] pci 0000:02:04.0: IO window: 0x00a400-0x00a4ff
[ 0.239135] pci 0000:02:04.0: IO window: 0x00a800-0x00a8ff
[ 0.239141] pci 0000:02:04.0: PREFETCH window: 0x1c000000-0x1fffffff
[ 0.239147] pci 0000:02:04.0: MEM window: 0x28000000-0x2bffffff
[ 0.239153] pci 0000:02:04.1: CardBus bridge, secondary bus 0000:04
[ 0.239157] pci 0000:02:04.1: IO window: 0x00ac00-0x00acff
[ 0.239163] pci 0000:02:04.1: IO window: 0x001400-0x0014ff
[ 0.239169] pci 0000:02:04.1: PREFETCH window: 0x20000000-0x23ffffff
[ 0.239175] pci 0000:02:04.1: MEM window: 0x2c000000-0x2fffffff
[ 0.239181] pci 0000:00:14.4: PCI bridge, secondary bus 0000:02
[ 0.239186] pci 0000:00:14.4: IO window: 0xa000-0xafff
[ 0.239192] pci 0000:00:14.4: MEM window: 0xe8200000-0xe82fffff
[ 0.239197] pci 0000:00:14.4: PREFETCH window: 0x1c000000-0x23ffffff
[ 0.239233] alloc irq_desc for 17 on node -1
[ 0.239237] alloc kstat_irqs on node -1
[ 0.239251] pci 0000:02:04.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.239265] alloc irq_desc for 16 on node -1
[ 0.239269] alloc kstat_irqs on node -1
[ 0.239276] pci 0000:02:04.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.239288] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.239293] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.239297] pci_bus 0000:01: resource 0 io: [0x9000-0x9fff]
[ 0.239302] pci_bus 0000:01: resource 1 mem: [0xe8100000-0xe81fffff]
[ 0.239306] pci_bus 0000:01: resource 2 pref mem [0xf0000000-0xf7ffffff]
[ 0.239311] pci_bus 0000:02: resource 0 io: [0xa000-0xafff]
[ 0.239315] pci_bus 0000:02: resource 1 mem: [0xe8200000-0xe82fffff]
[ 0.239320] pci_bus 0000:02: resource 2 pref mem [0x1c000000-0x23ffffff]
[ 0.239324] pci_bus 0000:02: resource 3 io: [0x00-0xffff]
[ 0.239328] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
[ 0.239333] pci_bus 0000:03: resource 0 io: [0xa400-0xa4ff]
[ 0.239337] pci_bus 0000:03: resource 1 io: [0xa800-0xa8ff]
[ 0.239342] pci_bus 0000:03: resource 2 pref mem [0x1c000000-0x1fffffff]
[ 0.239347] pci_bus 0000:03: resource 3 mem: [0x28000000-0x2bffffff]
[ 0.239352] pci_bus 0000:04: resource 0 io: [0xac00-0xacff]
[ 0.239356] pci_bus 0000:04: resource 1 io: [0x1400-0x14ff]
[ 0.239361] pci_bus 0000:04: resource 2 pref mem [0x20000000-0x23ffffff]
[ 0.239366] pci_bus 0000:04: resource 3 mem: [0x2c000000-0x2fffffff]
[ 0.239433] NET: Registered protocol family 2
[ 0.239584] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.240025] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.240086] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.240149] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.240155] TCP reno registered
[ 0.240375] NET: Registered protocol family 1
[ 0.240505] Trying to unpack rootfs image as initramfs...
[ 0.561513] Freeing initrd memory: 7464k freed
[ 0.577774] cpufreq-nforce2: No nForce2 chipset.
[ 0.577839] Scanning for low memory corruption every 60 seconds
[ 0.578082] audit: initializing netlink socket (disabled)
[ 0.578113] type=2000 audit(1260973709.575:1): initialized
[ 0.586109] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.588549] VFS: Disk quotas dquot_6.5.2
[ 0.588684] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.590042] fuse init (API version 7.12)
[ 0.590282] msgmni has been set to 361
[ 0.590890] alg: No test for stdrng (krng)
[ 0.590949] io scheduler noop registered
[ 0.590953] io scheduler anticipatory registered
[ 0.590957] io scheduler deadline registered
[ 0.591105] io scheduler cfq registered (default)
[ 0.591176] pci 0000:01:05.0: Boot video device
[ 0.591428] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.591481] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.594458] ACPI: AC Adapter [ACAD] (on-line)
[ 0.594588] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 0.594597] ACPI: Power Button [PWRF]
[ 0.594689] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
[ 0.594790] ACPI: Lid Switch [LID]
[ 0.594894] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[ 0.594902] ACPI: Power Button [PWRB]
[ 0.595251] Marking TSC unstable due to TSC halts in idle
[ 0.595318] Switched to high resolution mode on CPU 0
[ 0.595363] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 0.595424] processor LNXCPU:00: registered as cooling_device0
[ 0.630684] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.630705] ACPI: Thermal Zone [THRM] (53 C)
[ 0.630869] isapnp: Scanning for PnP cards...
[ 0.810662] ACPI: Battery Slot [BAT1] (battery absent)
[ 0.984539] isapnp: No Plug & Play device found
[ 0.987700] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.988390] serial 0000:00:14.6: PCI INT B -> GSI 5 (level, low) -> IRQ 5
[ 0.988402] serial 0000:00:14.6: PCI INT B disabled
[ 0.990557] brd: module loaded
[ 0.991665] loop: module loaded
[ 0.991890] input: Macintosh mouse button emulation as /devices/virtual/input/input3
[ 0.992684] pata_atiixp 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.992946] scsi0 : pata_atiixp
[ 0.993223] scsi1 : pata_atiixp
[ 0.994984] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x8060 irq 14
[ 0.994992] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x8068 irq 15
[ 0.996938] Fixed MDIO Bus: probed
[ 0.997036] PPP generic driver version 2.4.2
[ 0.997324] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.997407] alloc irq_desc for 19 on node -1
[ 0.997415] alloc kstat_irqs on node -1
[ 0.997429] ehci_hcd 0000:02:07.2: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[ 0.997464] ehci_hcd 0000:02:07.2: EHCI Host Controller
[ 0.997627] ehci_hcd 0000:02:07.2: new USB bus registered, assigned bus number 1
[ 1.020093] ehci_hcd 0000:02:07.2: irq 19, io mem 0xe8204400
[ 1.032030] ehci_hcd 0000:02:07.2: USB 2.0 started, EHCI 1.00
[ 1.032207] usb usb1: configuration #1 chosen from 1 choice
[ 1.032284] hub 1-0:1.0: USB hub found
[ 1.032311] hub 1-0:1.0: 5 ports detected
[ 1.032480] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.032539] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 1.032575] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 1.032716] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
[ 1.032756] ohci_hcd 0000:00:13.0: irq 19, io mem 0xe8001000
[ 1.092207] usb usb2: configuration #1 chosen from 1 choice
[ 1.092292] hub 2-0:1.0: USB hub found
[ 1.092323] hub 2-0:1.0: 3 ports detected
[ 1.092452] ohci_hcd 0000:00:13.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 1.092488] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 1.092625] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
[ 1.092665] ohci_hcd 0000:00:13.1: irq 19, io mem 0xe8002000
[ 1.152406] usb usb3: configuration #1 chosen from 1 choice
[ 1.152495] hub 3-0:1.0: USB hub found
[ 1.152527] hub 3-0:1.0: 3 ports detected
[ 1.152674] ohci_hcd 0000:02:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.152710] ohci_hcd 0000:02:07.0: OHCI Host Controller
[ 1.152864] ohci_hcd 0000:02:07.0: new USB bus registered, assigned bus number 4
[ 1.152918] ohci_hcd 0000:02:07.0: irq 16, io mem 0xe8202000
[ 1.207601] ata1.00: ATA-7: WDC WD800BEVE-22UYT0, 01.04A01, max UDMA/100
[ 1.207607] ata1.00: 156301488 sectors, multi 16: LBA48
[ 1.238331] usb usb4: configuration #1 chosen from 1 choice
[ 1.238412] hub 4-0:1.0: USB hub found
[ 1.238441] hub 4-0:1.0: 3 ports detected
[ 1.238580] alloc irq_desc for 18 on node -1
[ 1.238587] alloc kstat_irqs on node -1
[ 1.238601] ohci_hcd 0000:02:07.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[ 1.238636] ohci_hcd 0000:02:07.1: OHCI Host Controller
[ 1.238768] ohci_hcd 0000:02:07.1: new USB bus registered, assigned bus number 5
[ 1.238821] ohci_hcd 0000:02:07.1: irq 18, io mem 0xe8203000
[ 1.239069] ata1.00: configured for UDMA/100
[ 1.239331] scsi 0:0:0:0: Direct-Access ATA WDC WD800BEVE-22 01.0 PQ: 0 ANSI: 5
[ 1.239657] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.239830] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 1.240117] sd 0:0:0:0: [sda] Write Protect is off
[ 1.240125] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.240248] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.240811] sda: sda1 sda2 < sda5 >
[ 1.273116] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.321999] usb usb5: configuration #1 chosen from 1 choice
[ 1.322090] hub 5-0:1.0: USB hub found
[ 1.322120] hub 5-0:1.0: 2 ports detected
[ 1.322263] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.322481] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 1.332667] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 1.338048] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.338063] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.338186] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.338193] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.338199] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.338414] mice: PS/2 mouse device common for all mice
[ 1.338714] rtc_cmos 00:03: RTC can wake from S4
[ 1.338812] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.338848] rtc0: alarms up to one day, 242 bytes nvram
[ 1.339120] device-mapper: uevent: version 1.0.3
[ 1.339425] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 1.341544] device-mapper: multipath: version 1.1.0 loaded
[ 1.341552] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.341994] EISA: Probing bus 0 at eisa.0
[ 1.342006] Cannot allocate resource for EISA slot 1
[ 1.342026] Cannot allocate resource for EISA slot 8
[ 1.342029] EISA: Detected 0 cards.
[ 1.342698] cpuidle: using governor ladder
[ 1.342799] cpuidle: using governor menu
[ 1.343651] TCP cubic registered
[ 1.344043] NET: Registered protocol family 10
[ 1.344775] lo: Disabled Privacy Extensions
[ 1.345183] NET: Registered protocol family 17
[ 1.345251] Bluetooth: L2CAP ver 2.13
[ 1.345255] Bluetooth: L2CAP socket layer initialized
[ 1.345262] Bluetooth: SCO (Voice Link) ver 0.6
[ 1.345265] Bluetooth: SCO socket layer initialized
[ 1.345797] Bluetooth: RFCOMM TTY layer initialized
[ 1.345808] Bluetooth: RFCOMM socket layer initialized
[ 1.345812] Bluetooth: RFCOMM ver 1.11
[ 1.345882] Using IPI No-Shortcut mode
[ 1.346163] PM: Resume from disk failed.
[ 1.346200] registered taskstats version 1
[ 1.346384] Magic number: 5:649:485
[ 1.346520] rtc_cmos 00:03: setting system clock to 2009-12-16 14:28:32 UTC (1260973712)
[ 1.346527] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.346530] EDD information not available.
[ 1.378725] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 1.404368] ata2.00: ATAPI: HL-DT-STCD-RW/DVD DRIVE GCC-4241N, 0C29, max MWDMA2
[ 1.420388] ata2.00: configured for MWDMA2
[ 1.426603] scsi 1:0:0:0: CD-ROM HL-DT-ST RW/DVD GCC-4241N 0C29 PQ: 0 ANSI: 5
[ 1.439277] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 1.439286] Uniform CD-ROM driver Revision: 3.20
[ 1.439497] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.439644] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 1.439712] Freeing unused kernel memory: 540k freed
[ 1.440825] Write protecting the kernel text: 4568k
[ 1.440864] Write protecting the kernel read-only data: 1836k
[ 1.795161] Linux agpgart interface v0.103
[ 1.798123] agpgart-ati 0000:00:00.0: Ati IGP9100/M chipset
[ 1.861831] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:01/device:02/input/input5
[ 1.861933] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 1.895170] agpgart-ati 0000:00:00.0: AGP aperture is 32M @ 0xea000000
[ 2.138729] [drm] Initialized drm 1.1.0 20060810
[ 2.210776] [drm] radeon default to kernel modesetting DISABLED.
[ 2.210938] pci 0000:01:05.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.211344] [drm] Initialized radeon 1.31.0 20080528 for 0000:01:05.0 on minor 0
[ 2.221141] b43-pci-bridge 0000:02:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 2.224683] ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0
[ 2.230727] <6>8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 2.230794] 8139cp 0000:02:03.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 2.250319] 8139too Fast Ethernet driver 0.9.28
[ 2.250422] 8139too 0000:02:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 2.251738] eth0: RealTek RTL8139 at 0xa000, 00:02:3f:21:26:c4, IRQ 19
[ 2.258956] b44.c:v2.0
[ 2.258983] b44: Invalid MAC address found in EEPROM
[ 2.258987] b44 ssb0:1: Problem fetching invariants of chip, aborting.
[ 2.259003] b44: probe of ssb0:1 failed with error -22
[ 4.892055] floppy0: no floppy controllers found
[ 5.703017] PM: Starting manual resume from disk
[ 5.703027] PM: Resume from partition 8:5
[ 5.703030] PM: Checking hibernation image.
[ 5.703370] PM: Resume from disk failed.
[ 5.762636] EXT4-fs (sda1): barriers enabled
[ 5.781437] kjournald2 starting: pid 307, dev sda1:8, commit interval 5 seconds
[ 5.781479] EXT4-fs (sda1): delayed allocation enabled
[ 5.781486] EXT4-fs: file extents enabled
[ 5.791282] EXT4-fs: mballoc enabled
[ 5.791328] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 6.603473] type=1505 audit(1260973717.754:2): operation="profile_load" pid=330 name=/sbin/dhclient3
[ 6.604208] type=1505 audit(1260973717.757:3): operation="profile_load" pid=330 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[ 6.604582] type=1505 audit(1260973717.757:4): operation="profile_load" pid=330 name=/usr/lib/connman/scripts/dhclient-script
[ 6.643527] type=1505 audit(1260973717.793:5): operation="profile_load" pid=331 name=/usr/bin/evince
[ 6.654130] type=1505 audit(1260973717.805:6): operation="profile_load" pid=331 name=/usr/bin/evince-previewer
[ 6.660422] type=1505 audit(1260973717.813:7): operation="profile_load" pid=331 name=/usr/bin/evince-thumbnailer
[ 6.705958] type=1505 audit(1260973717.857:8): operation="profile_load" pid=333 name=/usr/lib/cups/backend/cups-pdf
[ 6.706794] type=1505 audit(1260973717.857:9): operation="profile_load" pid=333 name=/usr/sbin/cupsd
[ 6.721801] type=1505 audit(1260973717.873:10): operation="profile_load" pid=334 name=/usr/sbin/tcpdump
[ 7.997526] Adding 546168k swap on /dev/sda5. Priority:-1 extents:1 across:546168k
[ 8.614058] udev: starting version 147
[ 8.616330] EXT4-fs (sda1): internal journal on sda1:8
[ 10.577760] yenta_cardbus 0000:02:04.0: CardBus bridge found [103c:006b]
[ 10.577784] yenta_cardbus 0000:02:04.0: Enabling burst memory read transactions
[ 10.577790] yenta_cardbus 0000:02:04.0: Using CSCINT to route CSC interrupts to PCI
[ 10.577794] yenta_cardbus 0000:02:04.0: Routing CardBus interrupts to PCI
[ 10.577801] yenta_cardbus 0000:02:04.0: TI: mfunc 0x01111d22, devctl 0x64
[ 10.644591] ACPI: I/O resource piix4_smbus [0x8040-0x8047] conflicts with ACPI region PMIO [0x8020-0x805f]
[ 10.644600] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 10.644614] piix4_smbus: probe of 0000:00:14.0 failed with error -16
[ 10.808802] yenta_cardbus 0000:02:04.0: ISA IRQ mask 0x0e98, PCI irq 17
[ 10.808809] yenta_cardbus 0000:02:04.0: Socket status: 30000006
[ 10.808823] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
[ 10.808829] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa000-0xafff: clean.
[ 10.809046] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge Memory window: 0xe8200000 - 0xe82fffff
[ 10.809050] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge Memory window: 0x1c000000 - 0x23ffffff
[ 10.809408] yenta_cardbus 0000:02:04.1: CardBus bridge found [103c:006b]
[ 10.809432] yenta_cardbus 0000:02:04.1: Using CSCINT to route CSC interrupts to PCI
[ 10.809436] yenta_cardbus 0000:02:04.1: Routing CardBus interrupts to PCI
[ 10.809443] yenta_cardbus 0000:02:04.1: TI: mfunc 0x01111d22, devctl 0x64
[ 11.040794] yenta_cardbus 0000:02:04.1: ISA IRQ mask 0x0e98, PCI irq 16
[ 11.040801] yenta_cardbus 0000:02:04.1: Socket status: 30000006
[ 11.040808] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #04 to #07
[ 11.040825] yenta_cardbus 0000:02:04.1: pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
[ 11.040830] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa000-0xafff: clean.
[ 11.041046] yenta_cardbus 0000:02:04.1: pcmcia: parent PCI bridge Memory window: 0xe8200000 - 0xe82fffff
[ 11.041051] yenta_cardbus 0000:02:04.1: pcmcia: parent PCI bridge Memory window: 0x1c000000 - 0x23ffffff
[ 11.368770] cfg80211: Calling CRDA to update world regulatory domain
[ 11.473665] input: PS/2 Mouse as /devices/platform/i8042/serio4/input/input6
[ 11.496492] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio4/input/input7
[ 11.529537] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3af: excluding 0x378-0x37f
[ 11.530898] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x4d0-0x4d7
[ 11.531556] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x820-0x8ff: clean.
[ 11.532192] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07
[ 11.533154] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff: clean.
[ 11.547669] parport_pc 00:09: reported by Plug and Play ACPI
[ 11.547706] parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
[ 11.973526] cfg80211: World regulatory domain updated:
[ 11.973536] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 11.973541] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.973546] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.973550] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.973555] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.973560] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.239415] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[ 12.240819] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x4d0-0x4d7
[ 12.241467] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 12.242027] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07
[ 12.242967] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 12.263253] lp0: using parport0 (interrupt-driven).
[ 12.267699] ppdev: user-space parallel port driver
[ 12.765662] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.769293] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 12.865065] b43legacy-phy0: Broadcom 4301 WLAN found
[ 12.888100] b43legacy-phy0 debug: Found PHY: Analog 0, Type 1, Revision 4
[ 12.888126] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[ 12.916052] b43legacy-phy0 debug: Radio initialized
[ 13.527549] phy0: Selected rate control algorithm 'minstrel'
[ 13.528676] Broadcom 43xx-legacy driver loaded [ Features: PLID, Firmware-ID: FW10 ]
[ 13.571752] udev: renamed network interface wlan0 to wlan5
[ 13.632059] floppy0: no floppy controllers found
[ 14.417411] type=1505 audit(1260973725.569:11): operation="profile_replace" pid=716 name=/sbin/dhclient3
[ 14.418121] type=1505 audit(1260973725.569:12): operation="profile_replace" pid=716 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[ 14.418529] type=1505 audit(1260973725.569:13): operation="profile_replace" pid=716 name=/usr/lib/connman/scripts/dhclient-script
[ 14.441038] type=1505 audit(1260973725.593:14): operation="profile_replace" pid=717 name=/usr/bin/evince
[ 14.453621] type=1505 audit(1260973725.605:15): operation="profile_replace" pid=717 name=/usr/bin/evince-previewer
[ 14.460556] type=1505 audit(1260973725.613:16): operation="profile_replace" pid=717 name=/usr/bin/evince-thumbnailer
[ 14.475509] type=1505 audit(1260973725.625:17): operation="profile_replace" pid=719 name=/usr/lib/cups/backend/cups-pdf
[ 14.476433] type=1505 audit(1260973725.629:18): operation="profile_replace" pid=719 name=/usr/sbin/cupsd
[ 14.481643] type=1505 audit(1260973725.633:19): operation="profile_replace" pid=720 name=/usr/sbin/tcpdump
[ 15.463419] ATI IXP AC97 controller 0000:00:14.5: PCI INT B -> GSI 5 (level, low) -> IRQ 5
[ 16.000689] ATI IXP MC97 controller 0000:00:14.6: PCI INT B -> GSI 5 (level, low) -> IRQ 5
[ 17.864095] b43legacy ssb0:0: firmware: requesting b43legacy/ucode2.fw
[ 18.039205] b43legacy ssb0:0: firmware: requesting b43legacy/pcm4.fw
[ 18.085786] b43legacy ssb0:0: firmware: requesting b43legacy/b0g0initvals2.fw
[ 18.244902] b43legacy-phy0: Loading firmware version 0x127, patch level 14 (2005-04-18 02:36:27)
[ 18.376648] b43legacy-phy0 debug: Chip initialized
[ 18.377026] b43legacy-phy0 debug: 30-bit DMA initialized
[ 18.381507] Registered led device: b43legacy-phy0::tx
[ 18.381559] Registered led device: b43legacy-phy0::rx
[ 18.381620] Registered led device: b43legacy-phy0::radio
[ 18.381663] b43legacy-phy0 debug: Wireless interface started
[ 18.381679] b43legacy-phy0 debug: Adding Interface type 2
[ 18.392679] ADDRCONF(NETDEV_UP): wlan5: link is not ready
[ 18.397997] eth0: link down
[ 18.398112] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.400135] b43legacy-phy0: Radio hardware status changed to DISABLED
[ 18.400178] b43legacy-phy0 debug: Radio initialized
[ 18.400305] b43legacy-phy0 debug: Removing Interface type 2
[ 18.400453] b43legacy-phy0 debug: Wireless interface stopped
[ 18.400721] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots: 0/64
[ 18.400780] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots: 0/64
[ 18.400848] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots: 0/128
[ 18.408244] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots: 0/128
[ 18.416089] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots: 0/128
[ 18.424068] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots: 0/128
[ 18.432112] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots: 0/128
[ 18.440068] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots: 0/128
[ 18.449310] b43legacy-phy0 debug: Radio initialized
[ 18.449327] b43legacy-phy0 debug: Radio initialized
[ 21.294234] agpgart-ati 0000:00:00.0: AGP 3.0 bridge
[ 21.294261] agpgart-ati 0000:00:00.0: putting AGP V3 device into 8x mode
[ 21.294284] pci 0000:01:05.0: putting AGP V3 device into 8x mode
[ 21.450375] [drm] Setting GART location based on new memory map
[ 21.450390] [drm] Loading R200 Microcode
[ 21.450441] [drm] writeback test succeeded in 1 usecs
[ 363.396331] b43legacy-phy1: Broadcom 4301 WLAN found
[ 363.420040] b43legacy-phy1 debug: Found PHY: Analog 0, Type 1, Revision 4
[ 363.420068] b43legacy-phy1 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[ 363.444047] b43legacy-phy1 debug: Radio initialized
[ 363.445072] phy1: Selected rate control algorithm 'minstrel'
[ 363.446174] Broadcom 43xx-legacy driver loaded [ Features: PLID, Firmware-ID: FW10 ]
[ 363.534830] udev: renamed network interface wlan0 to wlan5
[ 363.740095] b43legacy ssb0:0: firmware: requesting b43legacy/ucode2.fw
[ 364.089441] b43legacy ssb0:0: firmware: requesting b43legacy/pcm4.fw
[ 364.127135] b43legacy ssb0:0: firmware: requesting b43legacy/b0g0initvals2.fw
[ 364.380054] b43legacy-phy1: Loading firmware version 0x127, patch level 14 (2005-04-18 02:36:27)
[ 364.480314] b43legacy-phy1 debug: Chip initialized
[ 364.515241] b43legacy-phy1 debug: 30-bit DMA initialized
[ 364.515523] Registered led device: b43legacy-phy1::tx
[ 364.515579] Registered led device: b43legacy-phy1::rx
[ 364.515641] Registered led device: b43legacy-phy1::radio
[ 364.515685] b43legacy-phy1 debug: Wireless interface started
[ 364.515702] b43legacy-phy1 debug: Adding Interface type 2
[ 364.524165] ADDRCONF(NETDEV_UP): wlan5: link is not ready
[ 364.532115] b43legacy-phy1: Radio hardware status changed to DISABLED
[ 364.532157] b43legacy-phy1 debug: Radio initialized
[ 364.532389] b43legacy-phy1 debug: Removing Interface type 2
[ 364.532535] b43legacy-phy1 debug: Wireless interface stopped
[ 364.532845] b43legacy-phy1 debug: DMA-30 0x0260 (RX) max used slots: 0/64
[ 364.532912] b43legacy-phy1 debug: DMA-30 0x0200 (RX) max used slots: 0/64
[ 364.532976] b43legacy-phy1 debug: DMA-30 0x02A0 (TX) max used slots: 0/128
[ 364.540074] b43legacy-phy1 debug: DMA-30 0x0280 (TX) max used slots: 0/128
[ 364.548069] b43legacy-phy1 debug: DMA-30 0x0260 (TX) max used slots: 0/128
[ 364.556062] b43legacy-phy1 debug: DMA-30 0x0240 (TX) max used slots: 0/128
[ 364.564063] b43legacy-phy1 debug: DMA-30 0x0220 (TX) max used slots: 0/128
[ 364.572094] b43legacy-phy1 debug: DMA-30 0x0200 (TX) max used slots: 0/128
[ 364.580214] b43legacy-phy1 debug: Radio initialized
[ 364.580232] b43legacy-phy1 debug: Radio initialized
ms@abc:~$


Eιμαστε κοντα στη λυση του προβληματος;