Πρόβλημα στο Ubuntu με Wireless σύνδεση

...κάρτες δικτύου, modems, προβλήματα internet
Κανόνες Δ. Συζήτησης
Για την ευκολότερη επίλυση του προβλήματός σας.
Καλό είναι να δημοσιεύσετε τα αποτελέσματα των εντολών στο τερματικό :
lspci -nn
lsusb
rfkill list

Re: Πρόβλημα στο Ubuntu με Wireless σύνδεση

Δημοσίευσηαπό linuxman » 26 Σεπ 2008, 18:50

xristosn έγραψε:
rizitis έγραψε: πήγαινε Σύστημα(system) ->Διαχειριστής(administration) -> και διάβασε μία μία τις ονομασίες των εφαρμογών που θα εμφανιστούν στο πλάι.
και πες μας αν υπάρχει κάποια που να ονομάζετε οδηγός ασύρματης δικτύωσης των windows ή κάπως έτσι.


Όχι δεν υπάρχει. Για δίκτυο υπάρχουν μόνο τα: α) Δίκτυο και β) Εργαλεία Δικτύου

πήγαινε Σύστημα(system) ->Διαχειριστής(administration)-> Δίκτυο και δες εάν υπάρχει εδώ Ασύρματη Δικτύωση
Οδηγίες προς Νεοεισερχόμενους
1 Γνώσεις Linux: Πολύ καλό ┃ Προγραμματισμού: Ικανοποιητικό ┃ Αγγλικών: Ικανοποιητικό
2 Linux Mint 17.1 Rebecca 3.13.0-37-generic 64bit (el_GR.UTF-8, X-Cinnamon cinnamon)
3 Intel Core i5-2310M CPU @ 2.10GHz ‖ RAM 3866 MiB ‖ Dell Inc. 0D7C51 - Dell Inc. Dell System Vostro 3750
4 Intel 2nd Generation Core Processor Family Integrated Graphics [8086:0116] {i915}
5 wlan0: Intel Centrino Wireless-N 1030 [Rainbow Peak] [8086:008a] (rev 34) ⋮ eth0: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 06)
http://www.greeklug.gr
Άβαταρ μέλους
linuxman
Επίτιμο μέλος
Επίτιμο μέλος
 
Δημοσιεύσεις: 10378
Εγγραφή: 10 Μάιος 2008, 20:41
Τοποθεσία: Thessaloniki / Macedonia / Greece
Εκτύπωση

Re: Πρόβλημα στο Ubuntu με Wireless σύνδεση

Δημοσίευσηαπό xristosn » 26 Σεπ 2008, 18:53

Πήγα τερματικό έγραψα την εντολή
Κώδικας: Επιλογή όλων
sudo gedit /etc/modprobe.d/blacklist
έγραψα
Κώδικας: Επιλογή όλων
blacklist ndiswrapper
δεν έβαλα το το # μπροστά όμως, την εντολή την έγραψα σε μια νέα γραμμή, έκανα restart και αμέσως μετά από την κονσόλα έδωσα
Κώδικας: Επιλογή όλων
lsmode
και πήρα
Κώδικας: Επιλογή όλων
xristos@dalaki:~$ lsmod
Module Size Used by
i915 32512 2
drm 82964 3 i915
snd_rtctimer 4640 1
af_packet 24196 2
rfcomm 43280 2
l2cap 25984 13 rfcomm
bluetooth 62564 4 rfcomm,l2cap
ipv6 275236 14
ppdev 10372 0
acpi_cpufreq 10924 0
cpufreq_conservative 8840 0
cpufreq_stats 7360 0
cpufreq_powersave 2688 0
cpufreq_userspace 5284 0
cpufreq_ondemand 9740 1
freq_table 5536 3 acpi_cpufreq,cpufreq_stats,cpufreq_ondemand
container 5760 0
dock 11564 0
sbs 15368 0
sbshc 7808 1 sbs
iptable_filter 3840 0
ip_tables 14820 1 iptable_filter
x_tables 16644 1 ip_tables
sbp2 24456 0
parport_pc 36516 0
lp 13252 0
parport 38600 3 ppdev,parport_pc,lp
joydev 13248 0
pcmcia 41260 0
evdev 13312 7
battery 14596 0
ac 7044 0
pcspkr 4224 0
psmouse 41104 0
serio_raw 7940 0
snd_intel8x0 35228 3
snd_ac97_codec 101284 1 snd_intel8x0
ac97_bus 3200 1 snd_ac97_codec
snd_pcm_oss 42400 0
snd_mixer_oss 18048 1 snd_pcm_oss
snd_pcm 78724 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
video 19984 0
output 4736 1 video
snd_seq_dummy 4868 0
sdhci 19204 0
tifm_7xx1 8576 0
mmc_core 52228 1 sdhci
tifm_core 11780 1 tifm_7xx1
yenta_socket 27404 2
rsrc_nonstatic 13696 1 yenta_socket
pcmcia_core 41136 3 pcmcia,yenta_socket,rsrc_nonstatic
snd_seq_oss 35968 0
wmi_acer 9772 0
snd_seq_midi 9376 0
snd_rawmidi 25632 1 snd_seq_midi
button 9232 0
snd_seq_midi_event 8576 2 snd_seq_oss,snd_seq_midi
iTCO_wdt 13524 0
iTCO_vendor_support 4868 1 iTCO_wdt
snd_seq 54992 7 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 24836 3 snd_rtctimer,snd_pcm,snd_seq
snd_seq_device 9612 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 57636 19 snd_rtctimer,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_dummy,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 9312 1 snd
snd_page_alloc 11400 2 snd_intel8x0,snd_pcm
shpchp 34708 0
pci_hotplug 31776 1 shpchp
intel_agp 25492 1
agpgart 34900 3 drm,intel_agp
ext3 137480 2
jbd 49044 1 ext3
mbcache 9856 1 ext3
sg 36624 0
sr_mod 18084 0
cdrom 37152 1 sr_mod
sd_mod 31232 4
pata_acpi 8320 0
usbhid 32640 0
hid 39040 1 usbhid
8139too 27392 0
ata_piix 19716 3
ata_generic 8452 0
libata 160112 3 pata_acpi,ata_piix,ata_generic
8139cp 24704 0
ohci1394 34096 0
scsi_mod 153196 5 sbp2,sg,sr_mod,sd_mod,libata
mii 6400 2 8139too,8139cp
ieee1394 95544 2 sbp2,ohci1394
ehci_hcd 37644 0
uhci_hcd 26896 0
usbcore 147308 4 usbhid,ehci_hcd,uhci_hcd
thermal 16924 0
processor 37896 3 acpi_cpufreq,thermal
fan 5636 0
fuse 51604 3
xristos@dalaki:~$


και
Κώδικας: Επιλογή όλων
dmesg
και πήρα
Κώδικας: Επιλογή όλων
[ 0.000000] ACPI: DMI detected: Hewlett-Packard
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:13 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000dc000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000dc000 - 0000000000100000
[ 0.000000] Real-Time Preemption Support (C) 2004-2007 Ingo Molnar
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 514816
[ 0.000000] Kernel command line: root=UUID=9564dfa9-c122-425a-95ed-bc78cb555392 ro quiet splash
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1496.767 MHz processor.
[ 8.074798] Console: colour VGA+ 80x25
[ 8.074802] console [tty0] enabled
[ 8.075221] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 8.075757] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 8.223703] Memory: 2045468k/2087808k available (2225k kernel code, 41048k reserved, 1059k data, 368k init, 1170304k highmem)
[ 8.223713] virtual kernel memory layout:
[ 8.223714] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 8.223715] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 8.223717] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 8.223718] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 8.223720] .init : 0xc043b000 - 0xc0497000 ( 368 kB)
[ 8.223721] .data : 0xc032c6d0 - 0xc0435324 (1059 kB)
[ 8.223723] .text : 0xc0100000 - 0xc032c6d0 (2225 kB)
[ 8.223727] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 8.283900] Calibrating delay using timer specific routine.. 2995.52 BogoMIPS (lpj=1497760)
[ 8.283967] Security Framework initialized
[ 8.283980] SELinux: Disabled at boot.
[ 8.283992] AppArmor: AppArmor initialized
[ 8.283999] Failure registering capabilities with primary security module.
[ 8.284019] Mount-cache hash table entries: 512
[ 8.284247] Initializing cgroup subsys ns
[ 8.284255] Initializing cgroup subsys cpuacct
[ 8.284273] CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000 00000000
[ 8.284289] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 8.284292] CPU: L2 cache: 2048K
[ 8.284296] CPU: After all inits, caps: afe9fbff 00100000 00000000 00042040 00000180 00000000 00000000 00000000
[ 8.284310] Compat vDSO mapped to ffffe000.
[ 8.284330] Checking 'hlt' instruction... OK.
[ 8.288380] SMP alternatives: switching to UP code
[ 8.289994] Freeing SMP alternatives: 9k freed
[ 8.290138] Early unpacking initramfs... done
[ 8.708995] ACPI: Core revision 20070126
[ 8.709092] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 8.736939] CPU0: Intel(R) Pentium(R) M processor 1.50GHz stepping 08
[ 8.736964] Total of 1 processors activated (2995.52 BogoMIPS).
[ 8.737160] ENABLING IO-APIC IRQs
[ 8.737362] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 8.849153] Brought up 1 CPUs
[ 8.849183] CPU0 attaching sched-domain:
[ 8.849186] domain 0: span 01
[ 8.849189] groups: 01
[ 8.849413] net_namespace: 76 bytes
[ 8.849427] Booting paravirtualized kernel on bare hardware
[ 8.849975] Time: 15:32:59 Date: 09/26/08
[ 8.850022] NET: Registered protocol family 16
[ 8.850273] EISA bus registered
[ 8.850299] ACPI: bus type pci registered
[ 8.850908] PCI: PCI BIOS revision 2.10 entry at 0xfd850, last bus=7
[ 8.850911] PCI: Using configuration type 1
[ 8.850927] Setting up standard PCI resources
[ 8.862179] ACPI: EC: Look up EC in DSDT
[ 8.863674] ACPI: Interpreter enabled
[ 8.863686] ACPI: (supports S0 S3 S4 S5)
[ 8.863703] ACPI: Using IOAPIC for interrupt routing
[ 8.866405] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 8.870215] ACPI: EC: GPE = 0x1b, I/O: command/status = 0x66, data = 0x62
[ 8.870219] ACPI: EC: driver started in interrupt mode
[ 8.870267] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 8.871099] Force enabled HPET at base address 0xfed00000
[ 8.871106] PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 8.871111] PCI quirk: region 1180-11bf claimed by ICH6 GPIO
[ 8.871858] PCI: Transparent bridge - 0000:00:1e.0
[ 8.871949] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 8.872192] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 8.872336] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 8.874795] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 8.874893] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 8.874987] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 8.875080] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 8.875175] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 8.875269] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 8.875366] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 8.875459] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 8.875603] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 8.875643] pnp: PnP ACPI init
[ 8.875650] ACPI: bus type pnp registered
[ 8.878379] pnp: PnP ACPI: found 8 devices
[ 8.878382] ACPI: ACPI bus type pnp unregistered
[ 8.878386] PnPBIOS: Disabled by ACPI PNP
[ 8.878667] PCI: Using ACPI for IRQ routing
[ 8.878670] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 8.878683] PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.0
[ 8.878688] PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.0
[ 8.878690] PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.0
[ 8.909670] NET: Registered protocol family 8
[ 8.909674] NET: Registered protocol family 20
[ 8.909862] hpet clockevent registered
[ 8.909869] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 8.909874] hpet0: 3 64-bit timers, 14318180 Hz
[ 8.910940] AppArmor: AppArmor Filesystem Enabled
[ 8.921703] system 00:04: ioport range 0x200-0x20f has been reserved
[ 8.921707] system 00:04: ioport range 0x800-0x80f has been reserved
[ 8.921710] system 00:04: ioport range 0x1000-0x107f has been reserved
[ 8.921714] system 00:04: ioport range 0x1180-0x11bf has been reserved
[ 8.921718] system 00:04: iomem range 0xe0000000-0xefffffff could not be reserved
[ 8.921721] system 00:04: iomem range 0xf0000000-0xf0003fff could not be reserved
[ 8.921725] system 00:04: iomem range 0xf0004000-0xf0004fff could not be reserved
[ 8.921729] system 00:04: iomem range 0xf0005000-0xf0005fff could not be reserved
[ 8.921732] system 00:04: iomem range 0xf0008000-0xf000bfff could not be reserved
[ 8.921736] system 00:04: iomem range 0xfed20000-0xfed8ffff could not be reserved
[ 8.952246] PCI: Bridge: 0000:00:1c.0
[ 8.952249] IO window: disabled.
[ 8.952255] MEM window: disabled.
[ 8.952260] PREFETCH window: disabled.
[ 8.952269] PCI: Bus 7, cardbus bridge: 0000:06:06.0
[ 8.952272] IO window: 00003400-000034ff
[ 8.952278] IO window: 00003800-000038ff
[ 8.952284] PREFETCH window: 8c000000-8fffffff
[ 8.952289] MEM window: 90000000-93ffffff
[ 8.952295] PCI: Bridge: 0000:00:1e.0
[ 8.952298] IO window: 3000-3fff
[ 8.952305] MEM window: b0100000-b01fffff
[ 8.952309] PREFETCH window: disabled.
[ 8.952341] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 16
[ 8.952350] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 8.952365] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 8.952383] ACPI: PCI Interrupt 0000:06:06.0[A] -> GSI 22 (level, low) -> IRQ 17
[ 8.952390] PCI: Setting latency timer of device 0000:06:06.0 to 64
[ 8.952414] NET: Registered protocol family 2
[ 8.987707] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 8.987992] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 8.989192] TCP bind hash table entries: 65536 (order: 9, 2359296 bytes)
[ 8.992867] TCP: Hash tables configured (established 131072 bind 65536)
[ 8.992875] TCP reno registered
[ 9.004876] checking if image is initramfs... it is
[ 9.816456] Freeing initrd memory: 7305k freed
[ 9.816790] Simple Boot Flag at 0x36 set to 0x1
[ 9.817381] audit: initializing netlink socket (disabled)
[ 9.817401] audit(1222443179.466:1): initialized
[ 9.817615] krcupreemptd setsched 0
[ 9.817617] prio = 98
[ 9.817722] highmem bounce pool size: 64 pages
[ 9.817826] VFS: Disk quotas dquot_6.5.1
[ 9.817860] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 9.817979] io scheduler noop registered
[ 9.817982] io scheduler anticipatory registered
[ 9.817984] io scheduler deadline registered
[ 9.817999] io scheduler cfq registered (default)
[ 9.818018] Boot video device is 0000:00:02.0
[ 9.818280] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 9.818338] assign_interrupt_mode Found MSI capability
[ 9.818394] Allocate Port Service[0000:00:1c.0:pcie00]
[ 9.818441] Allocate Port Service[0000:00:1c.0:pcie02]
[ 9.818778] isapnp: Scanning for PnP cards...
[ 10.176353] isapnp: No Plug & Play device found
[ 10.210588] Real Time Clock Driver v1.12ac
[ 10.210737] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 10.211455] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 20 (level, low) -> IRQ 18
[ 10.211466] ACPI: PCI interrupt for device 0000:00:1e.3 disabled
[ 10.212368] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 10.212456] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 10.212576] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 10.217827] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 10.221340] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 10.221346] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 10.221349] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 10.221352] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 10.221355] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 10.231798] mice: PS/2 mouse device common for all mice
[ 10.231938] EISA: Probing bus 0 at eisa.0
[ 10.231947] Cannot allocate resource for EISA slot 1
[ 10.231951] Cannot allocate resource for EISA slot 2
[ 10.231953] Cannot allocate resource for EISA slot 3
[ 10.231976] EISA: Detected 0 cards.
[ 10.231980] cpuidle: using governor ladder
[ 10.232091] NET: Registered protocol family 1
[ 10.232124] Using IPI No-Shortcut mode
[ 10.232178] registered taskstats version 1
[ 10.232327] Magic number: 8:42:539
[ 10.232475] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 10.232477] EDD information not available.
[ 10.232751] Freeing unused kernel memory: 368k freed
[ 10.254693] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 10.664152] atkbd.c: Spurious NAK on isa0060/serio0. Some program might be trying access hardware directly.
[ 10.864129] atkbd.c: Spurious NAK on isa0060/serio0. Some program might be trying access hardware directly.
[ 11.064131] atkbd.c: Spurious NAK on isa0060/serio0. Some program might be trying access hardware directly.
[ 11.264951] atkbd.c: Spurious NAK on isa0060/serio0. Some program might be trying access hardware directly.
[ 11.507220] fuse init (API version 7.9)
[ 11.521964] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[ 11.521972] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 11.526579] ACPI: Thermal Zone [THR0] (52 C)
[ 11.529142] ACPI: Invalid passive threshold
[ 11.529928] ACPI: Thermal Zone [THR1] (40 C)
[ 12.206643] usbcore: registered new interface driver usbfs
[ 12.206671] usbcore: registered new interface driver hub
[ 12.215607] usbcore: registered new device driver usb
[ 12.230751] USB Universal Host Controller Interface driver v3.0
[ 12.230823] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19
[ 12.230836] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 12.230842] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 12.231288] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 12.243832] uhci_hcd 0000:00:1d.0: irq 19, io base 0x00001820
[ 12.243992] usb usb1: configuration #1 chosen from 1 choice
[ 12.244020] hub 1-0:1.0: USB hub found
[ 12.244029] hub 1-0:1.0: 2 ports detected
[ 12.344963] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 20
[ 12.344979] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 12.344985] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 12.345012] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 12.356588] uhci_hcd 0000:00:1d.1: irq 20, io base 0x00001840
[ 12.356726] usb usb2: configuration #1 chosen from 1 choice
[ 12.356754] hub 2-0:1.0: USB hub found
[ 12.356763] hub 2-0:1.0: 2 ports detected
[ 12.444479] SCSI subsystem initialized
[ 12.457707] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 21
[ 12.457723] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 12.457729] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 12.457756] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 12.469584] uhci_hcd 0000:00:1d.2: irq 21, io base 0x00001860
[ 12.469728] usb usb3: configuration #1 chosen from 1 choice
[ 12.469758] hub 3-0:1.0: USB hub found
[ 12.469766] hub 3-0:1.0: 2 ports detected
[ 12.484590] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 12.529567] libata version 3.00 loaded.
[ 12.570728] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 22
[ 12.570743] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 12.570749] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 12.570778] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 12.583590] uhci_hcd 0000:00:1d.3: irq 22, io base 0x00001880
[ 12.583742] usb usb4: configuration #1 chosen from 1 choice
[ 12.583771] hub 4-0:1.0: USB hub found
[ 12.583780] hub 4-0:1.0: 2 ports detected
[ 12.684772] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19
[ 12.684792] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 12.684797] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 12.684826] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 12.688747] ehci_hcd 0000:00:1d.7: debug port 1
[ 12.688754] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 12.688763] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xb0040000
[ 12.776565] usb 3-1: new low speed USB device using uhci_hcd and address 2
[ 12.782565] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 12.782725] usb usb5: configuration #1 chosen from 1 choice
[ 12.782755] hub 5-0:1.0: USB hub found
[ 12.782771] hub 5-0:1.0: 8 ports detected
[ 12.885085] ACPI: PCI Interrupt 0000:06:06.2[C] -> GSI 21 (level, low) -> IRQ 23
[ 12.939424] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[23] MMIO=[b0107000-b01077ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 12.940124] 8139cp 0000:06:07.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[ 12.940129] 8139cp 0000:06:07.0: Try the "8139too" driver instead.
[ 12.947746] ata_piix 0000:00:1f.1: version 2.12
[ 12.947764] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 21
[ 12.947806] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 12.951119] 8139too Fast Ethernet driver 0.9.28
[ 12.952430] scsi0 : ata_piix
[ 12.952486] scsi1 : ata_piix
[ 12.953092] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
[ 12.953096] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
[ 13.260532] usb 3-1: new low speed USB device using uhci_hcd and address 3
[ 13.260992] ata1.00: ATA-6: ST960821A, 3.02, max UDMA/100
[ 13.260995] ata1.00: 117210240 sectors, multi 16: LBA48
[ 13.261024] ata1.01: ATAPI: TSSTcorpCD/DVDW TS-L532R, HA04, max MWDMA2
[ 13.266909] ata1.00: configured for UDMA/100
[ 13.377814] usb 3-1: configuration #1 chosen from 1 choice
[ 13.398470] usbcore: registered new interface driver hiddev
[ 13.401419] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:1d.2/usb3/3-1/3-1:1.0/input/input2
[ 13.409523] Clocksource tsc unstable (delta = -2790972727 ns)
[ 13.409571] input,hidraw0: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.2-1
[ 13.409585] usbcore: registered new interface driver usbhid
[ 13.409589] /build/buildd/linux-2.6.24/debian/build/custom-source-rt/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 13.426612] ata1.01: configured for MWDMA2
[ 13.426669] ata2: port disabled. ignoring.
[ 13.426831] scsi 0:0:0:0: Direct-Access ATA ST960821A 3.02 PQ: 0 ANSI: 5
[ 13.427635] scsi 0:0:1:0: CD-ROM TSSTcorp CD/DVDW TS-L532R HA04 PQ: 0 ANSI: 5
[ 13.428130] ACPI: PCI Interrupt 0000:06:07.0[A] -> GSI 20 (level, low) -> IRQ 18
[ 13.429023] eth0: RealTek RTL8139 at 0x3000, 00:0a:e4:d1:5f:39, IRQ 18
[ 13.429027] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 13.444118] Driver 'sd' needs updating - please use bus_type methods
[ 13.444205] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[ 13.444220] sd 0:0:0:0: [sda] Write Protect is off
[ 13.444223] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 13.444242] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.444297] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[ 13.444309] sd 0:0:0:0: [sda] Write Protect is off
[ 13.444312] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 13.444331] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.444337] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 13.457463] sda1 sda2 sda3
[ 13.459032] sd 0:0:0:0: [sda] Attached SCSI disk
[ 13.467006] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 13.467027] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 13.468813] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 13.468817] Uniform CD-ROM driver Revision: 3.20
[ 13.468861] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 13.587413] Attempting manual resume
[ 13.587418] swsusp: Resume From Partition 8:2
[ 13.587421] PM: Checking swsusp image.
[ 13.587578] PM: Resume from disk failed.
[ 13.604667] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.604714] kjournald starting. Commit interval 5 seconds
[ 13.664115] ieee1394: Host added: ID:BUS[0-00:1023] GUID[05e40a00e7545016]
[ 16.884561] Linux agpgart interface v0.102
[ 17.031639] agpgart: Detected an Intel 915GM Chipset.
[ 17.032264] agpgart: Detected 7932K stolen memory.
[ 17.101574] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 17.176546] agpgart: AGP aperture is 256M @ 0xc0000000
[ 17.176583] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 17.660467] intel_rng: FWH not detected
[ 17.826456] iTCO_vendor_support: vendor-support=0
[ 17.856127] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[ 17.856294] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
[ 17.856350] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 17.928596] input: Power Button (FF) as /devices/virtual/input/input3
[ 17.937421] ACPI: Power Button (FF) [PWRF]
[ 17.937524] input: Lid Switch as /devices/virtual/input/input4
[ 17.938940] ACPI: Lid Switch [LID0]
[ 17.939021] input: Sleep Button (CM) as /devices/virtual/input/input5
[ 17.949415] ACPI: Sleep Button (CM) [SLPB]
[ 17.949504] input: Power Button (CM) as /devices/virtual/input/input6
[ 17.961411] ACPI: Power Button (CM) [PWB]
[ 18.136266] ACPI: WMI-Acer: Mapper loaded
[ 18.733456] Yenta: CardBus bridge found at 0000:06:06.0 [103c:3081]
[ 18.733482] Yenta: Enabling burst memory read transactions
[ 18.733488] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 18.733491] Yenta: Routing CardBus interrupts to PCI
[ 18.733497] Yenta TI: socket 0000:06:06.0, mfunc 0x01aa1b02, devctl 0x64
[ 19.018125] Yenta: ISA IRQ mask 0x0cf8, PCI irq 17
[ 19.018131] Socket status: 30000820
[ 19.018134] Yenta: Raising subordinate bus# of parent bus (#06) from #07 to #0a
[ 19.018140] pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
[ 19.018144] cs: IO port probe 0x3000-0x3fff: clean.
[ 19.018436] pcmcia: parent PCI bridge Memory window: 0xb0100000 - 0xb01fffff
[ 19.119881] ACPI: PCI Interrupt 0000:06:06.3[A] -> GSI 22 (level, low) -> IRQ 17
[ 19.158516] sdhci: Secure Digital Host Controller Interface driver
[ 19.158521] sdhci: Copyright(c) Pierre Ossman
[ 19.158613] sdhci: SDHCI controller found at 0000:06:06.4 [104c:8034] (rev 0)
[ 19.158637] ACPI: PCI Interrupt 0000:06:06.4[A] -> GSI 22 (level, low) -> IRQ 17
[ 19.158664] sdhci:slot0: Will use DMA mode even though HW doesn't fully claim to support it.
[ 19.158729] mmc0: SDHCI at 0xb0108000 irq 17 DMA
[ 19.158740] sdhci:slot1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 19.158788] mmc1: SDHCI at 0xb0107c00 irq 17 DMA
[ 19.158799] sdhci:slot2: Will use DMA mode even though HW doesn't fully claim to support it.
[ 19.158845] mmc2: SDHCI at 0xb0107800 irq 17 DMA
[ 19.372213] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input7
[ 19.680221] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 19.743224] pccard: CardBus card inserted into slot 0
[ 20.361268] ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 17 (level, low) -> IRQ 16
[ 20.361301] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[ 20.716967] pccard: card ejected from slot 0
[ 21.278039] intel8x0_measure_ac97_clock: measured 50463 usecs
[ 21.278044] intel8x0: clocking to 48000
[ 21.292441] input: PC Speaker as /devices/platform/pcspkr/input/input8
[ 21.334668] ACPI: AC Adapter [AC] (on-line)
[ 21.453032] ACPI: Battery Slot [BAT0] (battery present)
[ 21.470500] atkbd.c: Spurious NAK on isa0060/serio0. Some program might be trying access hardware directly.
[ 21.670520] atkbd.c: Spurious NAK on isa0060/serio0. Some program might be trying access hardware directly.
[ 22.154590] input: PS/2 Mouse as /devices/virtual/input/input9
[ 22.166951] pccard: CardBus card inserted into slot 0
[ 22.195420] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio4/input/input10
[ 22.494415] pccard: card ejected from slot 0
[ 23.567485] pccard: CardBus card inserted into slot 0
[ 23.575383] cs: IO port probe 0x100-0x3af: clean.
[ 23.577071] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 23.577819] cs: IO port probe 0x820-0x8ff: clean.
[ 23.578440] cs: IO port probe 0xc00-0xcf7: clean.
[ 23.579227] cs: IO port probe 0xa00-0xaff: clean.
[ 23.700839] lp: driver loaded but no devices found
[ 23.934182] Adding 1028152k swap on /dev/sda2. Priority:-1 extents:1 across:1028152k
[ 24.020326] pccard: card ejected from slot 0
[ 24.037496] EXT3 FS on sda1, internal journal
[ 24.223824] kjournald starting. Commit interval 5 seconds
[ 24.224001] EXT3 FS on sda3, internal journal
[ 24.224006] EXT3-fs: mounted filesystem with ordered data mode.
[ 24.637888] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 24.688628] pccard: CardBus card inserted into slot 0
[ 24.843599] pccard: card ejected from slot 0
[ 24.950447] No dock devices found.
[ 25.828185] pccard: CardBus card inserted into slot 0
[ 25.880548] pccard: card ejected from slot 0
[ 26.160292] pccard: CardBus card inserted into slot 0
[ 26.210712] pccard: card ejected from slot 0
[ 26.433899] pccard: CardBus card inserted into slot 0
[ 26.781172] apm: BIOS not found.
[ 26.888981] ppdev: user-space parallel port driver
[ 26.913215] audit(1222443216.006:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5067 profile="/usr/sbin/cupsd" namespace="default"
[ 33.749739] Marking TSC unstable due to: cpufreq changes.
[ 27.055841] NET: Registered protocol family 10
[ 27.056257] lo: Disabled Privacy Extensions
[ 27.567994] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 70.041523] Bluetooth: Core ver 2.11
[ 70.042596] NET: Registered protocol family 31
[ 70.044108] Bluetooth: HCI device and connection manager initialized
[ 70.044118] Bluetooth: HCI socket layer initialized
[ 28.106886] Bluetooth: L2CAP ver 2.9
[ 28.106892] Bluetooth: L2CAP socket layer initialized
[ 28.114152] Bluetooth: RFCOMM socket layer initialized
[ 28.114170] Bluetooth: RFCOMM TTY layer initialized
[ 28.114172] Bluetooth: RFCOMM ver 1.8
[ 28.245738] NET: Registered protocol family 17
[ 45.741635] [drm] Initialized drm 1.1.0 20060810
[ 45.748904] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 22
[ 45.748919] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 45.749018] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 32.995374] eth0: no IPv6 routers present
xristos@dalaki:~$
Επίπεδο Γνώσεων: Linux: Χαμηλό / Προγραμματισμός: Όχι/ Αγγλικά:Μέτρια/
Λειτουργικό Win XP, Mac OS και Ubuntu 8.04 LTS
Η/Υ&Μοντέλο HP dv4001EA: Επεξεργαστής Intel 1,5/ Μνήμη 512/ Κάρτα Γραφικών intel/ Κάρτα Ήχου AC'97 Audio Controller/
xristosn
babeTUX
babeTUX
 
Δημοσιεύσεις: 70
Εγγραφή: 10 Ιουν 2008, 19:37
Εκτύπωση

Re: Πρόβλημα στο Ubuntu με Wireless σύνδεση

Δημοσίευσηαπό linuxman » 26 Σεπ 2008, 18:59

Οκ, τώρα δεν το έχει φορτώσει δοκίμασε τώρα να επαναλάβεις τις εντολές που σου έδωσε logari81
Οδηγίες προς Νεοεισερχόμενους
1 Γνώσεις Linux: Πολύ καλό ┃ Προγραμματισμού: Ικανοποιητικό ┃ Αγγλικών: Ικανοποιητικό
2 Linux Mint 17.1 Rebecca 3.13.0-37-generic 64bit (el_GR.UTF-8, X-Cinnamon cinnamon)
3 Intel Core i5-2310M CPU @ 2.10GHz ‖ RAM 3866 MiB ‖ Dell Inc. 0D7C51 - Dell Inc. Dell System Vostro 3750
4 Intel 2nd Generation Core Processor Family Integrated Graphics [8086:0116] {i915}
5 wlan0: Intel Centrino Wireless-N 1030 [Rainbow Peak] [8086:008a] (rev 34) ⋮ eth0: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 06)
http://www.greeklug.gr
Άβαταρ μέλους
linuxman
Επίτιμο μέλος
Επίτιμο μέλος
 
Δημοσιεύσεις: 10378
Εγγραφή: 10 Μάιος 2008, 20:41
Τοποθεσία: Thessaloniki / Macedonia / Greece
Εκτύπωση

Re: Πρόβλημα στο Ubuntu με Wireless σύνδεση

Δημοσίευσηαπό xristosn » 26 Σεπ 2008, 19:03

linuxman έγραψε:
xristosn έγραψε:
rizitis έγραψε: πήγαινε Σύστημα(system) ->Διαχειριστής(administration) -> και διάβασε μία μία τις ονομασίες των εφαρμογών που θα εμφανιστούν στο πλάι.
και πες μας αν υπάρχει κάποια που να ονομάζετε οδηγός ασύρματης δικτύωσης των windows ή κάπως έτσι.


Όχι δεν υπάρχει. Για δίκτυο υπάρχουν μόνο τα: α) Δίκτυο και β) Εργαλεία Δικτύου

πήγαινε Σύστημα(system) ->Διαχειριστής(administration)-> Δίκτυο και δες εάν υπάρχει εδώ Ασύρματη Δικτύωση


Πήγα Σύστημα->Διαχείριση Συστήματος και έχει τα εξής: Hardware Testing, Myth TV, Synaptic, Γλωσσική υποστήριξη, Διαχείριση ενημερώσεων, Δίκτυο, Εκτύπωση, Εξουσιοδοτήσεις, Εργαλεία Δικτύου, Καταγραφές Συστήματος, Οδηγοί Υλικού, Παράθυρο εισόδου, Παρακολούθηση Συστήματος, Πηγές Λογισμικού, Υπηρεσίες, Χρήστες και Ομάδες, Ώρα και Ημερομηνία.
Επίπεδο Γνώσεων: Linux: Χαμηλό / Προγραμματισμός: Όχι/ Αγγλικά:Μέτρια/
Λειτουργικό Win XP, Mac OS και Ubuntu 8.04 LTS
Η/Υ&Μοντέλο HP dv4001EA: Επεξεργαστής Intel 1,5/ Μνήμη 512/ Κάρτα Γραφικών intel/ Κάρτα Ήχου AC'97 Audio Controller/
xristosn
babeTUX
babeTUX
 
Δημοσιεύσεις: 70
Εγγραφή: 10 Ιουν 2008, 19:37
Εκτύπωση

Re: Πρόβλημα στο Ubuntu με Wireless σύνδεση

Δημοσίευσηαπό linuxman » 26 Σεπ 2008, 19:06

Κάνε κλικ στο Δίκτυο , και δες εκεί έχει κάτι με ασύρματο ;
Οδηγίες προς Νεοεισερχόμενους
1 Γνώσεις Linux: Πολύ καλό ┃ Προγραμματισμού: Ικανοποιητικό ┃ Αγγλικών: Ικανοποιητικό
2 Linux Mint 17.1 Rebecca 3.13.0-37-generic 64bit (el_GR.UTF-8, X-Cinnamon cinnamon)
3 Intel Core i5-2310M CPU @ 2.10GHz ‖ RAM 3866 MiB ‖ Dell Inc. 0D7C51 - Dell Inc. Dell System Vostro 3750
4 Intel 2nd Generation Core Processor Family Integrated Graphics [8086:0116] {i915}
5 wlan0: Intel Centrino Wireless-N 1030 [Rainbow Peak] [8086:008a] (rev 34) ⋮ eth0: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 06)
http://www.greeklug.gr
Άβαταρ μέλους
linuxman
Επίτιμο μέλος
Επίτιμο μέλος
 
Δημοσιεύσεις: 10378
Εγγραφή: 10 Μάιος 2008, 20:41
Τοποθεσία: Thessaloniki / Macedonia / Greece
Εκτύπωση

Re: Πρόβλημα στο Ubuntu με Wireless σύνδεση

Δημοσίευσηαπό xristosn » 26 Σεπ 2008, 19:07

linuxman έγραψε:Οκ, τώρα δεν το έχει φορτώσει δοκίμασε τώρα να επαναλάβεις τις εντολές που σου έδωσε logari81


Ποιες δηλαδή???
Επίπεδο Γνώσεων: Linux: Χαμηλό / Προγραμματισμός: Όχι/ Αγγλικά:Μέτρια/
Λειτουργικό Win XP, Mac OS και Ubuntu 8.04 LTS
Η/Υ&Μοντέλο HP dv4001EA: Επεξεργαστής Intel 1,5/ Μνήμη 512/ Κάρτα Γραφικών intel/ Κάρτα Ήχου AC'97 Audio Controller/
xristosn
babeTUX
babeTUX
 
Δημοσιεύσεις: 70
Εγγραφή: 10 Ιουν 2008, 19:37
Εκτύπωση

Re: Πρόβλημα στο Ubuntu με Wireless σύνδεση

Δημοσίευσηαπό xristosn » 26 Σεπ 2008, 19:09

linuxman έγραψε:Κάνε κλικ στο Δίκτυο , και δες εκεί έχει κάτι με ασύρματο ;


Όχι δεν έχει μόνο το ethernet και το μόντεμ το ενσωματωμένο
Επίπεδο Γνώσεων: Linux: Χαμηλό / Προγραμματισμός: Όχι/ Αγγλικά:Μέτρια/
Λειτουργικό Win XP, Mac OS και Ubuntu 8.04 LTS
Η/Υ&Μοντέλο HP dv4001EA: Επεξεργαστής Intel 1,5/ Μνήμη 512/ Κάρτα Γραφικών intel/ Κάρτα Ήχου AC'97 Audio Controller/
xristosn
babeTUX
babeTUX
 
Δημοσιεύσεις: 70
Εγγραφή: 10 Ιουν 2008, 19:37
Εκτύπωση

Re: Πρόβλημα στο Ubuntu με Wireless σύνδεση

Δημοσίευσηαπό linuxman » 26 Σεπ 2008, 19:18

Τώρα μπορείς να δώσεις
Κώδικας: Επιλογή όλων
sudo iwconfig
και μετά
Κώδικας: Επιλογή όλων
sudo modprobe acx
και ξανά
Κώδικας: Επιλογή όλων
sudo iwconfig
και πόσταρε το αποτέλεσμα
Οδηγίες προς Νεοεισερχόμενους
1 Γνώσεις Linux: Πολύ καλό ┃ Προγραμματισμού: Ικανοποιητικό ┃ Αγγλικών: Ικανοποιητικό
2 Linux Mint 17.1 Rebecca 3.13.0-37-generic 64bit (el_GR.UTF-8, X-Cinnamon cinnamon)
3 Intel Core i5-2310M CPU @ 2.10GHz ‖ RAM 3866 MiB ‖ Dell Inc. 0D7C51 - Dell Inc. Dell System Vostro 3750
4 Intel 2nd Generation Core Processor Family Integrated Graphics [8086:0116] {i915}
5 wlan0: Intel Centrino Wireless-N 1030 [Rainbow Peak] [8086:008a] (rev 34) ⋮ eth0: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 06)
http://www.greeklug.gr
Άβαταρ μέλους
linuxman
Επίτιμο μέλος
Επίτιμο μέλος
 
Δημοσιεύσεις: 10378
Εγγραφή: 10 Μάιος 2008, 20:41
Τοποθεσία: Thessaloniki / Macedonia / Greece
Εκτύπωση

Re: Πρόβλημα στο Ubuntu με Wireless σύνδεση

Δημοσίευσηαπό xristosn » 26 Σεπ 2008, 19:24

Κώδικας: Επιλογή όλων
xristos@dalaki:~$ sudo iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

wlan0 IEEE 802.11b+/g+ ESSID:"" Nickname:"acx v0.3.36"
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Bit Rate:54 Mb/s Tx-Power=15 dBm Sensitivity=1/3
Retry min limit:7 RTS thr:off
Encryption key:off
Power Management:off
Link Quality=32/100 Signal level=5/100 Noise level=0/100
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

xristos@dalaki:~$ sudo modprobe acx
xristos@dalaki:~$ sudo iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

wlan0 IEEE 802.11b+/g+ ESSID:"" Nickname:"acx v0.3.36"
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Bit Rate:54 Mb/s Tx-Power=15 dBm Sensitivity=1/3
Retry min limit:7 RTS thr:off
Encryption key:off
Power Management:off
Link Quality:32/100 Signal level:5/100 Noise level:0/100
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0



Νομίζω ότι δεν αναγνωρίζει την κάρτα!!!
Επίπεδο Γνώσεων: Linux: Χαμηλό / Προγραμματισμός: Όχι/ Αγγλικά:Μέτρια/
Λειτουργικό Win XP, Mac OS και Ubuntu 8.04 LTS
Η/Υ&Μοντέλο HP dv4001EA: Επεξεργαστής Intel 1,5/ Μνήμη 512/ Κάρτα Γραφικών intel/ Κάρτα Ήχου AC'97 Audio Controller/
xristosn
babeTUX
babeTUX
 
Δημοσιεύσεις: 70
Εγγραφή: 10 Ιουν 2008, 19:37
Εκτύπωση

Re: Πρόβλημα στο Ubuntu με Wireless σύνδεση

Δημοσίευσηαπό logari81 » 26 Σεπ 2008, 19:35

υπομονη παρακαλώ

αν δεν την αναγνωριζε δεν θα υπηρχε αυτο:

wlan0 IEEE 802.11b+/g+ ESSID:"" Nickname:"acx v0.3.36"
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Bit Rate:54 Mb/s Tx-Power=15 dBm Sensitivity=1/3
Retry min limit:7 RTS thr:off
Encryption key:off
Power Management:off
Link Quality:32/100 Signal level:5/100 Noise level:0/100
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

δώσε τωρα την εντολή

Κώδικας: Επιλογή όλων
sudo iwlist wlan0 scan
http://opensourceecology.org/


Λειτουργικό: Ubuntu 10.04 lucid 64-bitΠροδιαγραφές: 4x Intel Core i5 CPU M 450 2.40GHz ‖ RAM 3696 MiB ‖ Lenovo KL3 - LENOVO IdeaPad Y560
Κάρτα γραφικών: ATI Device [1002:68c0]Ασύρματο: wlan0: Atheros Inc. AR928X Wireless Network Adapter (PCI-Express) [168c:002a] (rev 01)
logari81
Επίτιμο μέλος
Επίτιμο μέλος
 
Δημοσιεύσεις: 6074
Εγγραφή: 14 Μάιος 2008, 10:40
Εκτύπωση

ΠροηγούμενηΕπόμενο

  • ΣΧΕΤΙΚΑ ΘΕΜΑΤΑ
    ΑΠΑΝΤΗΣΕΙΣ
    ΠΡΟΒΟΛΕΣ
    ΣΥΓΓΡΑΦΕΑΣ

Επιστροφή στο Κάρτες Δικτύου (Ethernet, WiFi, Bluetooth) / Internet