Πρόβλημα με wi-fi σε desktop

[logari81]

νομίζω ότι λόγω της κάρτας γραφικών nvidia που έχεις χρειάζεσαι και τα headers οπότε εγκατεστησε και τα 2 παρακάτω πακέτα και ξαναδοκιμασε:
http://kernel.ubuntu.com/~kernel-ppa/ma ... 5_i386.deb
http://kernel.ubuntu.com/~kernel-ppa/ma ... 05_all.deb

(αυτό που κάνουμε είναι ενα πειραμα, δεν θα ειναι η μονιμη λύση, τον πυρήνα 2.6.37 θα τον αφαιρέσουμε μετά, η διαδικασια ειναι πλήρως αναστρέψιμη, μην φοβάσαι)

[Gk0ur0u]

Τα έβαλα κι αυτά

[logari81]

και; μετά από επανεκκινηση μπαινει σε γραφικό;

[Gk0ur0u]

Ναι κανονικά, δεν επέλεξα εγώ λειτουργικό

[logari81]

δουλευει το ασύρματο; δουλευει καλά; Αν όχι δώσε μας παλι τα αποτελέσματα των εντολών:

Κώδικας: Επιλογή όλων

dmesg
uname -a

[Gk0ur0u]

Δεν δουλεύει καθόλου.

dmesg

Κώδικας: Επιλογή όλων

[ 5803.516082] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5803.516089] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5803.516096] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5803.516110] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5803.516124] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5803.516138] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5803.516144] [<c0168889>] process_one_work+0xd9/0x330
[ 5803.516149] [<c015ea1a>] ? mod_timer+0xfa/0x240
[ 5803.516163] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5803.516168] [<c0169483>] worker_thread+0xb3/0x210
[ 5803.516172] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5803.516177] [<c016c9a5>] kthread+0x75/0x80
[ 5803.516181] [<c016c930>] ? kthread+0x0/0x80
[ 5803.516186] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5803.516191] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5804.164740] scsi 9:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[ 5804.165537] sd 9:0:0:0: Attached scsi generic sg2 type 0
[ 5804.167594] sd 9:0:0:0: [sdc] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
[ 5804.168262] sd 9:0:0:0: [sdc] Write Protect is off
[ 5804.168267] sd 9:0:0:0: [sdc] Mode Sense: 23 00 00 00
[ 5804.168271] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[ 5804.171712] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[ 5804.274421] sdc: sdc1
[ 5804.276458] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[ 5804.276461] sd 9:0:0:0: [sdc] Attached SCSI removable disk
[ 5804.516029] usb 2-6: no command feedback received (-110).
[ 5804.516035] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5804.516040] Pid: 264, comm: kworker/u:4 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5804.516043] Call Trace:
[ 5804.516055] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5804.516062] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5804.516068] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5804.516073] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5804.516081] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5804.516093] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5804.516105] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5804.516117] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5804.516122] [<c0168889>] process_one_work+0xd9/0x330
[ 5804.516127] [<c015ea1a>] ? mod_timer+0xfa/0x240
[ 5804.516139] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5804.516143] [<c0169483>] worker_thread+0xb3/0x210
[ 5804.516147] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5804.516151] [<c016c9a5>] kthread+0x75/0x80
[ 5804.516155] [<c016c930>] ? kthread+0x0/0x80
[ 5804.516159] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5804.516164] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5805.516039] usb 2-6: no command feedback received (-110).
[ 5805.516046] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5805.516052] Pid: 264, comm: kworker/u:4 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5805.516055] Call Trace:
[ 5805.516068] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5805.516076] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5805.516083] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5805.516090] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5805.516098] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5805.516112] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5805.516126] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5805.516140] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5805.516146] [<c0168889>] process_one_work+0xd9/0x330
[ 5805.516151] [<c015ea1a>] ? mod_timer+0xfa/0x240
[ 5805.516165] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5805.516170] [<c0169483>] worker_thread+0xb3/0x210
[ 5805.516174] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5805.516179] [<c016c9a5>] kthread+0x75/0x80
[ 5805.516183] [<c016c930>] ? kthread+0x0/0x80
[ 5805.516188] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5805.516193] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5806.516034] usb 2-6: no command feedback received (-110).
[ 5806.516041] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5806.516047] Pid: 264, comm: kworker/u:4 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5806.516050] Call Trace:
[ 5806.516063] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5806.516071] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5806.516078] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5806.516085] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5806.516093] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5806.516106] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5806.516121] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5806.516135] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5806.516140] [<c0168889>] process_one_work+0xd9/0x330
[ 5806.516145] [<c015ea1a>] ? mod_timer+0xfa/0x240
[ 5806.516159] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5806.516164] [<c0169483>] worker_thread+0xb3/0x210
[ 5806.516168] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5806.516173] [<c016c9a5>] kthread+0x75/0x80
[ 5806.516177] [<c016c930>] ? kthread+0x0/0x80
[ 5806.516182] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5806.516188] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5807.516048] usb 2-6: no command feedback received (-110).
[ 5807.516054] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5807.516060] Pid: 264, comm: kworker/u:4 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5807.516063] Call Trace:
[ 5807.516076] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5807.516084] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5807.516091] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5807.516097] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5807.516106] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5807.516119] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5807.516133] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5807.516147] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5807.516153] [<c0168889>] process_one_work+0xd9/0x330
[ 5807.516158] [<c015ea1a>] ? mod_timer+0xfa/0x240
[ 5807.516172] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5807.516177] [<c0169483>] worker_thread+0xb3/0x210
[ 5807.516181] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5807.516186] [<c016c9a5>] kthread+0x75/0x80
[ 5807.516190] [<c016c930>] ? kthread+0x0/0x80
[ 5807.516195] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5807.516200] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5808.516045] usb 2-6: no command feedback received (-110).
[ 5808.516052] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5808.516057] Pid: 264, comm: kworker/u:4 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5808.516060] Call Trace:
[ 5808.516073] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5808.516081] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5808.516088] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5808.516094] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5808.516103] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5808.516116] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5808.516131] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5808.516145] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5808.516150] [<c0168889>] process_one_work+0xd9/0x330
[ 5808.516155] [<c015ea1a>] ? mod_timer+0xfa/0x240
[ 5808.516169] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5808.516174] [<c0169483>] worker_thread+0xb3/0x210
[ 5808.516178] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5808.516183] [<c016c9a5>] kthread+0x75/0x80
[ 5808.516187] [<c016c930>] ? kthread+0x0/0x80
[ 5808.516192] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5808.516197] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5809.516050] usb 2-6: no command feedback received (-110).
[ 5809.516057] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5809.516063] Pid: 264, comm: kworker/u:4 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5809.516066] Call Trace:
[ 5809.516079] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5809.516087] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5809.516095] [<c0167816>] ? __queue_work+0xd6/0x240
[ 5809.516102] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5809.516108] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5809.516113] [<c0167a3c>] ? queue_work_on+0x2c/0x40
[ 5809.516126] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5809.516140] [<f81b0798>] __ieee80211_scan_completed_finish+0x18/0x90 [mac80211]
[ 5809.516155] [<f81b140b>] ieee80211_scan_work+0xcb/0x190 [mac80211]
[ 5809.516159] [<c0168889>] process_one_work+0xd9/0x330
[ 5809.516164] [<c015ea1a>] ? mod_timer+0xfa/0x240
[ 5809.516179] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5809.516184] [<c0169483>] worker_thread+0xb3/0x210
[ 5809.516188] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5809.516193] [<c016c9a5>] kthread+0x75/0x80
[ 5809.516197] [<c016c930>] ? kthread+0x0/0x80
[ 5809.516202] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5809.516207] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5823.732065] usb 1-5: USB disconnect, address 5
[ 5856.516038] usb 2-6: no command feedback received (-110).
[ 5856.516046] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5856.516051] Pid: 265, comm: kworker/u:5 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5856.516055] Call Trace:
[ 5856.516067] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5856.516075] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5856.516083] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5856.516089] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5856.516103] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5856.516117] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5856.516131] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5856.516139] [<c0168889>] process_one_work+0xd9/0x330
[ 5856.516153] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5856.516158] [<c0169483>] worker_thread+0xb3/0x210
[ 5856.516162] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5856.516167] [<c016c9a5>] kthread+0x75/0x80
[ 5856.516172] [<c016c930>] ? kthread+0x0/0x80
[ 5856.516176] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5856.516181] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5857.516029] usb 2-6: no command feedback received (-110).
[ 5857.516034] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5857.516038] Pid: 265, comm: kworker/u:5 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5857.516042] Call Trace:
[ 5857.516051] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5857.516058] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5857.516066] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5857.516072] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5857.516078] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5857.516091] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5857.516105] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5857.516119] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5857.516124] [<c0168889>] process_one_work+0xd9/0x330
[ 5857.516138] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5857.516143] [<c0169483>] worker_thread+0xb3/0x210
[ 5857.516147] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5857.516152] [<c016c9a5>] kthread+0x75/0x80
[ 5857.516156] [<c016c930>] ? kthread+0x0/0x80
[ 5857.516160] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5857.516165] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5858.516030] usb 2-6: no command feedback received (-110).
[ 5858.516034] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5858.516038] Pid: 265, comm: kworker/u:5 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5858.516041] Call Trace:
[ 5858.516050] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5858.516058] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5858.516065] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5858.516071] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5858.516077] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5858.516089] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5858.516103] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5858.516117] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5858.516122] [<c0168889>] process_one_work+0xd9/0x330
[ 5858.516136] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5858.516141] [<c0169483>] worker_thread+0xb3/0x210
[ 5858.516145] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5858.516150] [<c016c9a5>] kthread+0x75/0x80
[ 5858.516154] [<c016c930>] ? kthread+0x0/0x80
[ 5858.516158] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5858.516163] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5859.516028] usb 2-6: no command feedback received (-110).
[ 5859.516032] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5859.516037] Pid: 265, comm: kworker/u:5 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5859.516040] Call Trace:
[ 5859.516050] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5859.516058] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5859.516065] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5859.516071] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5859.516076] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5859.516089] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5859.516103] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5859.516117] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5859.516122] [<c0168889>] process_one_work+0xd9/0x330
[ 5859.516136] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5859.516141] [<c0169483>] worker_thread+0xb3/0x210
[ 5859.516145] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5859.516149] [<c016c9a5>] kthread+0x75/0x80
[ 5859.516154] [<c016c930>] ? kthread+0x0/0x80
[ 5859.516158] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5859.516162] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5860.516031] usb 2-6: no command feedback received (-110).
[ 5860.516035] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5860.516040] Pid: 265, comm: kworker/u:5 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5860.516043] Call Trace:
[ 5860.516052] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5860.516059] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5860.516067] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5860.516073] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5860.516078] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5860.516091] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5860.516105] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5860.516119] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5860.516124] [<c0168889>] process_one_work+0xd9/0x330
[ 5860.516138] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5860.516143] [<c0169483>] worker_thread+0xb3/0x210
[ 5860.516147] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5860.516152] [<c016c9a5>] kthread+0x75/0x80
[ 5860.516156] [<c016c930>] ? kthread+0x0/0x80
[ 5860.516160] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5860.516165] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5861.516042] usb 2-6: no command feedback received (-110).
[ 5861.516046] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5861.516050] Pid: 265, comm: kworker/u:5 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5861.516053] Call Trace:
[ 5861.516062] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5861.516070] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5861.516077] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5861.516083] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5861.516088] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5861.516101] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5861.516115] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5861.516129] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5861.516134] [<c0168889>] process_one_work+0xd9/0x330
[ 5861.516148] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5861.516152] [<c0169483>] worker_thread+0xb3/0x210
[ 5861.516157] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5861.516161] [<c016c9a5>] kthread+0x75/0x80
[ 5861.516166] [<c016c930>] ? kthread+0x0/0x80
[ 5861.516170] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5861.516174] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5862.516028] usb 2-6: no command feedback received (-110).
[ 5862.516033] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5862.516037] Pid: 265, comm: kworker/u:5 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5862.516040] Call Trace:
[ 5862.516049] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5862.516057] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5862.516064] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5862.516070] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5862.516076] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5862.516088] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5862.516102] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5862.516116] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5862.516121] [<c0168889>] process_one_work+0xd9/0x330
[ 5862.516136] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5862.516140] [<c0169483>] worker_thread+0xb3/0x210
[ 5862.516144] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5862.516149] [<c016c9a5>] kthread+0x75/0x80
[ 5862.516153] [<c016c930>] ? kthread+0x0/0x80
[ 5862.516157] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5862.516162] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5863.516024] usb 2-6: no command feedback received (-110).
[ 5863.516028] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5863.516033] Pid: 265, comm: kworker/u:5 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5863.516036] Call Trace:
[ 5863.516045] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5863.516053] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5863.516060] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5863.516066] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5863.516072] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5863.516084] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5863.516098] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5863.516112] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5863.516117] [<c0168889>] process_one_work+0xd9/0x330
[ 5863.516131] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5863.516136] [<c0169483>] worker_thread+0xb3/0x210
[ 5863.516140] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5863.516145] [<c016c9a5>] kthread+0x75/0x80
[ 5863.516149] [<c016c930>] ? kthread+0x0/0x80
[ 5863.516154] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5863.516158] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5864.516036] usb 2-6: no command feedback received (-110).
[ 5864.516041] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5864.516045] Pid: 265, comm: kworker/u:5 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5864.516048] Call Trace:
[ 5864.516057] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5864.516065] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5864.516072] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5864.516078] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5864.516083] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5864.516096] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5864.516110] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5864.516124] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5864.516129] [<c0168889>] process_one_work+0xd9/0x330
[ 5864.516143] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5864.516148] [<c0169483>] worker_thread+0xb3/0x210
[ 5864.516152] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5864.516156] [<c016c9a5>] kthread+0x75/0x80
[ 5864.516161] [<c016c930>] ? kthread+0x0/0x80
[ 5864.516165] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5864.516169] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5865.516030] usb 2-6: no command feedback received (-110).
[ 5865.516034] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5865.516039] Pid: 265, comm: kworker/u:5 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5865.516042] Call Trace:
[ 5865.516051] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5865.516059] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5865.516066] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5865.516072] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5865.516078] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5865.516091] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5865.516105] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5865.516118] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5865.516124] [<c0168889>] process_one_work+0xd9/0x330
[ 5865.516138] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5865.516142] [<c0169483>] worker_thread+0xb3/0x210
[ 5865.516146] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5865.516151] [<c016c9a5>] kthread+0x75/0x80
[ 5865.516155] [<c016c930>] ? kthread+0x0/0x80
[ 5865.516159] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5865.516164] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5866.516037] usb 2-6: no command feedback received (-110).
[ 5866.516042] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5866.516046] Pid: 265, comm: kworker/u:5 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5866.516049] Call Trace:
[ 5866.516058] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5866.516066] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5866.516073] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5866.516079] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5866.516085] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5866.516097] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5866.516111] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5866.516125] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5866.516130] [<c0168889>] process_one_work+0xd9/0x330
[ 5866.516144] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5866.516149] [<c0169483>] worker_thread+0xb3/0x210
[ 5866.516153] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5866.516158] [<c016c9a5>] kthread+0x75/0x80
[ 5866.516163] [<c016c930>] ? kthread+0x0/0x80
[ 5866.516167] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5866.516171] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5867.516025] usb 2-6: no command feedback received (-110).
[ 5867.516029] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5867.516034] Pid: 265, comm: kworker/u:5 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5867.516037] Call Trace:
[ 5867.516045] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5867.516053] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5867.516060] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5867.516066] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5867.516072] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5867.516084] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5867.516098] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5867.516112] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5867.516116] [<c0168889>] process_one_work+0xd9/0x330
[ 5867.516131] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5867.516135] [<c0169483>] worker_thread+0xb3/0x210
[ 5867.516140] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5867.516144] [<c016c9a5>] kthread+0x75/0x80
[ 5867.516149] [<c016c930>] ? kthread+0x0/0x80
[ 5867.516153] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5867.516157] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5868.516036] usb 2-6: no command feedback received (-110).
[ 5868.516041] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5868.516045] Pid: 265, comm: kworker/u:5 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5868.516048] Call Trace:
[ 5868.516057] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5868.516065] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5868.516072] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5868.516079] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5868.516084] [<c0172fe5>] ? pm_qos_request+0x35/0x60
[ 5868.516097] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5868.516111] [<f81b06bc>] ieee80211_scan_state_set_channel+0x3c/0xa0 [mac80211]
[ 5868.516125] [<f81b1482>] ieee80211_scan_work+0x142/0x190 [mac80211]
[ 5868.516130] [<c0168889>] process_one_work+0xd9/0x330
[ 5868.516144] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5868.516148] [<c0169483>] worker_thread+0xb3/0x210
[ 5868.516153] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5868.516157] [<c016c9a5>] kthread+0x75/0x80
[ 5868.516162] [<c016c930>] ? kthread+0x0/0x80
[ 5868.516166] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5868.516170] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5869.516026] usb 2-6: no command feedback received (-110).
[ 5869.516031] ar9170 cmd: 08 01 00 00 f0 36 1c 00 00 50 00 00 .....6...P..
[ 5869.516037] Pid: 265, comm: kworker/u:5 Tainted: P 2.6.37-020637rc3-generic #201011220905
[ 5869.516040] Call Trace:
[ 5869.516050] [<f81eac5a>] ar9170_usb_exec_cmd+0x1ba/0x200 [ar9170usb]
[ 5869.516058] [<f81edc44>] ar9170_write_reg+0x54/0xa0 [ar9170usb]
[ 5869.516064] [<c0167816>] ? __queue_work+0xd6/0x240
[ 5869.516071] [<f81eeb08>] ar9170_set_slot_time+0x38/0x50 [ar9170usb]
[ 5869.516077] [<f81ec23a>] ar9170_op_config+0x4a/0xc0 [ar9170usb]
[ 5869.516082] [<c0167a3c>] ? queue_work_on+0x2c/0x40
[ 5869.516094] [<f81ac505>] ieee80211_hw_config+0xd5/0x140 [mac80211]
[ 5869.516108] [<f81b0798>] __ieee80211_scan_completed_finish+0x18/0x90 [mac80211]
[ 5869.516122] [<f81b140b>] ieee80211_scan_work+0xcb/0x190 [mac80211]
[ 5869.516127] [<c0168889>] process_one_work+0xd9/0x330
[ 5869.516141] [<f81b1340>] ? ieee80211_scan_work+0x0/0x190 [mac80211]
[ 5869.516146] [<c0169483>] worker_thread+0xb3/0x210
[ 5869.516150] [<c01693d0>] ? worker_thread+0x0/0x210
[ 5869.516155] [<c016c9a5>] kthread+0x75/0x80
[ 5869.516159] [<c016c930>] ? kthread+0x0/0x80
[ 5869.516164] [<c01032fe>] kernel_thread_helper+0x6/0x10
[ 5869.516168] ieee80211 phy0: writing reg 0x1c36f0 (val 0x5000) failed
[ 5876.840045] usb 1-5: new high speed USB device using ehci_hcd and address 6
[ 5876.974958] usb 1-5: selecting invalid altsetting 1
[ 5876.975043] scsi10 : usb-storage 1-5:1.0
[ 5877.972754] scsi 10:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[ 5877.973553] sd 10:0:0:0: Attached scsi generic sg2 type 0
[ 5877.975722] sd 10:0:0:0: [sdc] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
[ 5877.976560] sd 10:0:0:0: [sdc] Write Protect is off
[ 5877.976565] sd 10:0:0:0: [sdc] Mode Sense: 23 00 00 00
[ 5877.976569] sd 10:0:0:0: [sdc] Assuming drive cache: write through
[ 5877.979225] sd 10:0:0:0: [sdc] Assuming drive cache: write through
[ 5878.079442] sdc: sdc1
[ 5878.080728] sd 10:0:0:0: [sdc] Assuming drive cache: write through
[ 5878.080732] sd 10:0:0:0: [sdc] Attached SCSI removable disk
dopa@dopa-HP-Compaq-dx7500-Microtower:~$



uname -a

Κώδικας: Επιλογή όλων

dopa@dopa-HP-Compaq-dx7500-Microtower:~$ uname -a
Linux dopa-HP-Compaq-dx7500-Microtower 2.6.37-020637rc3-generic #201011220905 SMP Mon Nov 22 10:21:28 UTC 2010 i686 GNU/Linux
dopa@dopa-HP-Compaq-dx7500-Microtower:~$


[logari81]

για δώσε και το αποτελεσμα της εντολής

Κώδικας: Επιλογή όλων

lsmod

μπορεί το linux να μην εχει πρόβλημα καν με το στικ αλλά με τις θύρες usb σου.

[Gk0ur0u]

πάντως αφού το βλέπει κανονικά το στικάκι υποθέτω ότι δεν ειναι το πρόβλημα στις θύρες.(και ό,τι άλλο συνδέω με usb δουλεύει κανονικά)

lsmod

Κώδικας: Επιλογή όλων

dopa@dopa-HP-Compaq-dx7500-Microtower:~$ lsmod
Module Size Used by
nls_iso8859_1 3293 0
nls_cp437 4931 0
vfat 9344 0
fat 47609 1 vfat
binfmt_misc 6586 1
arc4 1133 2
parport_pc 27846 0
ppdev 5245 0
carl9170 71436 0
snd_hda_codec_realtek 252133 1
snd_usb_audio 90444 1
snd_hda_intel 24332 2
snd_hda_codec 86476 2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 5181 2 snd_usb_audio,snd_hda_codec
snd_usbmidi_lib 17715 1 snd_usb_audio
snd_pcm 75543 3 snd_usb_audio,snd_hda_intel,snd_hda_codec
snd_seq_midi 4786 0
snd_rawmidi 17763 2 snd_usbmidi_lib,snd_seq_midi
nvidia 9329739 38
ar9170usb 48674 0
snd_seq_midi_event 5919 1 snd_seq_midi
snd_seq 47142 2 snd_seq_midi,snd_seq_midi_event
mac80211 245343 2 carl9170,ar9170usb
snd_timer 19824 2 snd_pcm,snd_seq
ath 13849 2 carl9170,ar9170usb
snd_seq_device 5776 3 snd_seq_midi,snd_rawmidi,snd_seq
gspca_ov519 34230 0
gspca_main 22768 1 gspca_ov519
intel_agp 9913 0
intel_gtt 13287 1 intel_agp
videodev 68263 1 gspca_main
cfg80211 144857 4 carl9170,ar9170usb,mac80211,ath
psmouse 58014 0
serio_raw 4062 0
snd 49949 17 snd_hda_codec_realtek,snd_usb_audio,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_usbmidi_lib,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
snd_page_alloc 7352 2 snd_hda_intel,snd_pcm
v4l1_compat 13912 1 videodev
agpgart 32238 3 nvidia,intel_agp,intel_gtt
soundcore 880 1 snd
lp 7400 0
parport 32560 3 parport_pc,ppdev,lp
usbhid 36648 0
hid 67486 1 usbhid
usb_storage 40290 0
uas 7466 0
firewire_ohci 25335 0
firewire_core 52533 1 firewire_ohci
e1000e 133440 0
crc_itu_t 1383 1 firewire_core
ahci 19176 2
libahci 20139 1 ahci
dopa@dopa-HP-Compaq-dx7500-Microtower:~$


[logari81]

πάντως αφού το βλέπει κανονικά το στικάκι υποθέτω ότι δεν ειναι το πρόβλημα στις θύρες

δεν έχει σημασια αυτο, θα δούμε.

[logari81]

ελπίζω να συνδέεις το στικ κατευθείαν σε κάποια θύρα κι όχι μεσω καλωδιού για προέκταση. Επίσης αν έχεις μπροστινές/πισω θυρες usb προτίμησε τις πισω.