network manager is not running Lubuntu 12.04

[lepidas]

network manager is not running και με αφηνει χωρις δικτυο. μετα απο restart, αλλες φορες λειτουργεί κανονικα,αλλες φορες λεει not running,άλλες φορές αρχικά λειτουργεί και κόβεται αργότερα.

[lepidas]

Κώδικας: Επιλογή όλων

lspci -nn
00:00.0 Host bridge [0600]: VIA Technologies, Inc. P4X333/P4X400/PT800 AGP Bridge [1106:3168] (rev 82)
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237/VX700 PCI Bridge [1106:b198]
00:0f.0 RAID bus controller [0104]: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller [1106:3149] (rev 80)
00:0f.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06)
00:10.0 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81)
00:10.1 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81)
00:10.2 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81)
00:10.3 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81)
00:10.4 USB controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 86)
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South] [1106:3227]
00:11.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller [1106:3059] (rev 60)
00:11.6 Communication controller [0780]: VIA Technologies, Inc. AC'97 Modem Controller [1106:3068] (rev 80)
00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 78)
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation NV11 [GeForce2 MX/MX 400] [10de:0110] (rev b2)


Κώδικας: Επιλογή όλων

lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter
Bus 001 Device 004: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB
Bus 002 Device 002: ID 1d57:0010
Bus 001 Device 005: ID 0fde:ca01
Bus 001 Device 006: ID 046d:0826 Logitech, Inc.

Κώδικας: Επιλογή όλων

rfkill list
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no


[the_eye]

Δώσε και το αποτέλεσμα της dmesg αφού βγάλει το μήνυμα.

[medigeek]

Να υποθέσω πως αυτό συμβαίνει μεσω wireless;
Μου συμβαίνει συχνά με το netbook, να κοπεί η σύνδεση ή να αναφέρει προβλήματα "server not found" και να χρειάζεται επανασυνδεση στο ασύρματο δίκτυο.

Επίσης, ίσως να είναι πρόβλημα μικρής ασυμβατότητας με την συσκευή usb που υποθέτω είναι usb 2.0, ενώ το usb hub είναι 1.0. Δώσε:

Κώδικας: Επιλογή όλων

sudo lsusb -vd 0bda:8187

[Learner]

Ένα workaround ίσως θα ήταν

Κώδικας: Επιλογή όλων

start network-manager

στο rc.local

[madvinegar]

Ένα workaround ίσως θα ήταν

Κώδικας: Επιλογή όλων

start network-manager

στο rc.local

Ως "nm-applet" δεν φορτωνεται?

[lepidas]

τις βλεπω τις απαντησεις αας και ευχαριστω, τωρα παω σπιτι να δωσω απαντησεις απο τον υπολογιστη

[lepidas]

Κώδικας: Επιλογή όλων

sudo lsusb -vd 0bda:8187

Bus 001 Device 003: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0bda Realtek Semiconductor Corp.
idProduct 0x8187 RTL8187 Wireless Adapter
bcdDevice 2.00
iManufacturer 1
iProduct 2 USB2.0 WLAN Adapter
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 81
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4 Wireless Network Card
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 9
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 2 USB2.0 WLAN Adapter
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x06 EP 6 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x07 EP 7 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x89 EP 9 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x0a EP 10 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x0b EP 11 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x0c EP 12 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)


[lepidas]

Κατάλαβα ότι έχει πρόβλημα με τα υπόλοιπα usb καλώδια που έχω βάλει, δε τα θέλει.
Όταν κάνω restart με το usb/repeater-καμερα-σταθμο, συνδεδεμένα τότε δεν λειτουργεί το wireless. Εάν κάνω restart χωρίς αυτά τότε λειτουργεί.

[lepidas]

dmesg

Κώδικας: Επιλογή όλων

[ 0.000000] HighMem zone: 34339 pages, LIFO batch:7
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 40000000:bf7c0000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 13 pages/cpu @f77dc000 s31616 r0 d21632 u53248
[ 0.000000] pcpu-alloc: s31616 r0 d21632 u53248 alloc=13*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259776
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-29-generic root=UUID=1339f5aa-48e5-400b-a4db-25cafaf734d3 ro quiet splash vt.handoff=7
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 4190720 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Initializing HighMem for node 0 (000377fe:0003ff30)
[ 0.000000] Memory: 1010240k/1047744k available (5615k kernel code, 37052k reserved, 2765k data, 712k init, 138440k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
[ 0.000000] .init : 0xc1830000 - 0xc18e2000 ( 712 kB)
[ 0.000000] .data : 0xc157be04 - 0xc182f580 (2765 kB)
[ 0.000000] .text : 0xc1000000 - 0xc157be04 (5615 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:2304 nr_irqs:512 16
[ 0.000000] CPU 0 irqstacks, hard=f5808000 soft=f580a000
[ 0.000000] vt handoff: transparent VT on vt#7
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration failed
[ 0.000000] TSC: Unable to calibrate against PIT
[ 0.000000] TSC: using PMTIMER reference calibration
[ 0.000000] Detected 2666.550 MHz processor.
[ 0.012004] Calibrating delay loop (skipped), value calculated using timer frequency.. 5333.10 BogoMIPS (lpj=10666200)
[ 0.012012] pid_max: default: 32768 minimum: 301
[ 0.012053] Security Framework initialized
[ 0.012090] AppArmor: AppArmor initialized
[ 0.012094] Yama: becoming mindful.
[ 0.012195] Mount-cache hash table entries: 512
[ 0.012423] Initializing cgroup subsys cpuacct
[ 0.012435] Initializing cgroup subsys memory
[ 0.012450] Initializing cgroup subsys devices
[ 0.012455] Initializing cgroup subsys freezer
[ 0.012459] Initializing cgroup subsys blkio
[ 0.012472] Initializing cgroup subsys perf_event
[ 0.012527] CPU0: Hyper-Threading is disabled
[ 0.012534] mce: CPU supports 4 MCE banks
[ 0.012552] CPU0: Thermal monitoring enabled (TM1)
[ 0.012560] using mwait in idle threads.
[ 0.016160] SMP alternatives: switching to UP code
[ 0.031688] ACPI: Core revision 20110623
[ 0.036036] ftrace: allocating 25891 entries in 51 pages
[ 0.040133] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.041395] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.081801] CPU0: Intel(R) Celeron(R) CPU 2.66GHz stepping 03
[ 0.084004] Performance Events: Netburst events, Netburst P4/Xeon PMU driver.
[ 0.084004] ... version: 0
[ 0.084004] ... bit width: 40
[ 0.084004] ... generic registers: 18
[ 0.084004] ... value mask: 000000ffffffffff
[ 0.084004] ... max period: 0000007fffffffff
[ 0.084004] ... fixed-purpose events: 0
[ 0.084004] ... event mask: 000000000003ffff
[ 0.084004] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.084004] Brought up 1 CPUs
[ 0.084004] Total of 1 processors activated (5333.10 BogoMIPS).
[ 0.084004] devtmpfs: initialized
[ 0.084004] EVM: security.selinux
[ 0.084004] EVM: security.SMACK64
[ 0.084004] EVM: security.capability
[ 0.084004] PM: Registering ACPI NVS region at 3ff40000 (720896 bytes)
[ 0.084004] print_constraints: dummy:
[ 0.084004] RTC time: 11:35:45, date: 08/19/12
[ 0.084090] NET: Registered protocol family 16
[ 0.084321] EISA bus registered
[ 0.084387] ACPI: bus type pci registered
[ 0.084575] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
[ 0.084579] PCI: Using configuration type 1 for base access
[ 0.086719] bio: create slab <bio-0> at 0
[ 0.086927] ACPI: Added _OSI(Module Device)
[ 0.086936] ACPI: Added _OSI(Processor Device)
[ 0.086940] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.086943] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.087836] ACPI: EC: Look up EC in DSDT
[ 0.089135] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.091901] ACPI: Interpreter enabled
[ 0.091923] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.091961] ACPI: Using IOAPIC for interrupt routing
[ 0.100387] ACPI: No dock devices found.
[ 0.100394] HEST: Table not found.
[ 0.100404] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.100553] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.100839] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.100844] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.100848] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.100853] pci_root PNP0A03:00: host bridge window [mem 0x40000000-0xffffffff] (ignored)
[ 0.100877] pci 0000:00:00.0: [1106:3168] type 0 class 0x000600
[ 0.100891] pci 0000:00:00.0: reg 10: [mem 0xe0000000-0xe3ffffff pref]
[ 0.100983] pci 0000:00:01.0: [1106:b198] type 1 class 0x000604
[ 0.101044] pci 0000:00:01.0: supports D1
[ 0.101083] pci 0000:00:0f.0: [1106:3149] type 0 class 0x000104
[ 0.101104] pci 0000:00:0f.0: reg 10: [io 0xefa8-0xefaf]
[ 0.101117] pci 0000:00:0f.0: reg 14: [io 0xefa4-0xefa7]
[ 0.101130] pci 0000:00:0f.0: reg 18: [io 0xef98-0xef9f]
[ 0.101142] pci 0000:00:0f.0: reg 1c: [io 0xefa0-0xefa3]
[ 0.101155] pci 0000:00:0f.0: reg 20: [io 0xef80-0xef8f]
[ 0.101167] pci 0000:00:0f.0: reg 24: [io 0xe800-0xe8ff]
[ 0.101229] pci 0000:00:0f.1: [1106:0571] type 0 class 0x000101
[ 0.101286] pci 0000:00:0f.1: reg 20: [io 0xfc00-0xfc0f]
[ 0.101366] pci 0000:00:10.0: [1106:3038] type 0 class 0x000c03
[ 0.101420] pci 0000:00:10.0: reg 20: [io 0xeec0-0xeedf]
[ 0.101469] pci 0000:00:10.0: supports D1 D2
[ 0.101473] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.101479] pci 0000:00:10.0: PME# disabled
[ 0.101501] pci 0000:00:10.1: [1106:3038] type 0 class 0x000c03
[ 0.101555] pci 0000:00:10.1: reg 20: [io 0xef00-0xef1f]
[ 0.101604] pci 0000:00:10.1: supports D1 D2
[ 0.101607] pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.101613] pci 0000:00:10.1: PME# disabled
[ 0.101634] pci 0000:00:10.2: [1106:3038] type 0 class 0x000c03
[ 0.101688] pci 0000:00:10.2: reg 20: [io 0xef20-0xef3f]
[ 0.101737] pci 0000:00:10.2: supports D1 D2
[ 0.101740] pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.101746] pci 0000:00:10.2: PME# disabled
[ 0.101767] pci 0000:00:10.3: [1106:3038] type 0 class 0x000c03
[ 0.101821] pci 0000:00:10.3: reg 20: [io 0xef40-0xef5f]
[ 0.101870] pci 0000:00:10.3: supports D1 D2
[ 0.101873] pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.101879] pci 0000:00:10.3: PME# disabled
[ 0.101899] pci 0000:00:10.4: [1106:3104] type 0 class 0x000c03
[ 0.101920] pci 0000:00:10.4: reg 10: [mem 0xdfe00000-0xdfe000ff]
[ 0.102003] pci 0000:00:10.4: supports D1 D2
[ 0.102007] pci 0000:00:10.4: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.102012] pci 0000:00:10.4: PME# disabled
[ 0.102038] pci 0000:00:11.0: [1106:3227] type 0 class 0x000601
[ 0.102114] HPET not enabled in BIOS. You might try hpet=force boot option
[ 0.102122] pci 0000:00:11.0: Enabled onboard AC97/MC97 devices
[ 0.102181] pci 0000:00:11.5: [1106:3059] type 0 class 0x000401
[ 0.102202] pci 0000:00:11.5: reg 10: [io 0xe000-0xe0ff]
[ 0.102289] pci 0000:00:11.5: supports D1 D2
[ 0.102311] pci 0000:00:11.6: [1106:3068] type 0 class 0x000780
[ 0.102332] pci 0000:00:11.6: reg 10: [io 0x0000-0x00ff]
[ 0.102440] pci 0000:00:12.0: [1106:3065] type 0 class 0x000200
[ 0.102461] pci 0000:00:12.0: reg 10: [io 0xe400-0xe4ff]
[ 0.102473] pci 0000:00:12.0: reg 14: [mem 0xdff00000-0xdff000ff]
[ 0.102550] pci 0000:00:12.0: supports D1 D2
[ 0.102554] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.102559] pci 0000:00:12.0: PME# disabled
[ 0.102627] pci 0000:01:00.0: [10de:0110] type 0 class 0x000300
[ 0.102648] pci 0000:01:00.0: reg 10: [mem 0xde000000-0xdeffffff]
[ 0.102659] pci 0000:01:00.0: reg 14: [mem 0xd0000000-0xd7ffffff pref]
[ 0.102699] pci 0000:01:00.0: reg 30: [mem 0xdfa00000-0xdfa0ffff pref]
[ 0.102778] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.102787] pci 0000:00:01.0: bridge window [mem 0xdd900000-0xdfafffff]
[ 0.102794] pci 0000:00:01.0: bridge window [mem 0xcd800000-0xdd7fffff pref]
[ 0.102805] pci_bus 0000:00: on NUMA node 0
[ 0.102811] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.103231] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x1e)
[ 0.107983] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
[ 0.108116] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
[ 0.108201] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
[ 0.108287] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 0.108373] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 0.108466] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 0.108554] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 0.108639] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 0.108867] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.108872] vgaarb: loaded
[ 0.108874] vgaarb: bridge control possible 0000:01:00.0
[ 0.109083] i2c-core: driver [aat2870] using legacy suspend method
[ 0.109087] i2c-core: driver [aat2870] using legacy resume method
[ 0.109255] SCSI subsystem initialized
[ 0.109372] libata version 3.00 loaded.
[ 0.109482] usbcore: registered new interface driver usbfs
[ 0.109508] usbcore: registered new interface driver hub
[ 0.109577] usbcore: registered new device driver usb
[ 0.109765] PCI: Using ACPI for IRQ routing
[ 0.109774] PCI: pci_cache_line_size set to 64 bytes
[ 0.109849] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.109854] reserve RAM buffer: 000000003ff30000 - 000000003fffffff
[ 0.110055] NetLabel: Initializing
[ 0.110059] NetLabel: domain hash size = 128
[ 0.110061] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.110079] NetLabel: unlabeled traffic allowed by default
[ 0.121905] AppArmor: AppArmor Filesystem Enabled
[ 0.121964] pnp: PnP ACPI init
[ 0.121997] ACPI: bus type pnp registered
[ 0.122173] pnp 00:00: [bus 00-ff]
[ 0.122178] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.122187] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.122191] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.122195] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.122199] pnp 00:00: [mem 0x00000000 window]
[ 0.122202] pnp 00:00: [mem 0x40000000-0xffffffff window]
[ 0.122295] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[ 0.122330] pnp 00:01: [dma 4]
[ 0.122335] pnp 00:01: [io 0x0000-0x000f]
[ 0.122338] pnp 00:01: [io 0x0081-0x0083]
[ 0.122341] pnp 00:01: [io 0x0087]
[ 0.122344] pnp 00:01: [io 0x0089-0x008b]
[ 0.122347] pnp 00:01: [io 0x008f]
[ 0.122351] pnp 00:01: [io 0x00c0-0x00df]
[ 0.122400] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.122422] pnp 00:02: [io 0x0070-0x0071]
[ 0.122442] pnp 00:02: [irq 8]
[ 0.122489] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.122507] pnp 00:03: [io 0x0061]
[ 0.122558] pnp 00:03: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.122577] pnp 00:04: [io 0x00f0-0x00ff]
[ 0.122588] pnp 00:04: [irq 13]
[ 0.122637] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.123070] pnp 00:05: [irq 4]
[ 0.123074] pnp 00:05: [dma 0 disabled]
[ 0.123078] pnp 00:05: [io 0x03f8-0x03ff]
[ 0.123223] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.123704] pnp 00:06: [irq 6]
[ 0.123709] pnp 00:06: [dma 2]
[ 0.123713] pnp 00:06: [io 0x03f0-0x03f5]
[ 0.123716] pnp 00:06: [io 0x03f7]
[ 0.123830] pnp 00:06: Plug and Play ACPI device, IDs PNP0700 (active)
[ 0.124351] pnp 00:07: [io 0x0378-0x037f]
[ 0.124356] pnp 00:07: [io 0x0778-0x077b]
[ 0.124368] pnp 00:07: [irq 7]
[ 0.124372] pnp 00:07: [dma 3]
[ 0.124640] pnp 00:07: Plug and Play ACPI device, IDs PNP0401 (active)
[ 0.125169] pnp 00:08: [io 0x0010-0x001f]
[ 0.125173] pnp 00:08: [io 0x0022-0x003f]
[ 0.125177] pnp 00:08: [io 0x0044-0x005f]
[ 0.125180] pnp 00:08: [io 0x0062-0x0063]
[ 0.125183] pnp 00:08: [io 0x0065-0x006f]
[ 0.125186] pnp 00:08: [io 0x0072-0x007f]
[ 0.125189] pnp 00:08: [io 0x0080]
[ 0.125193] pnp 00:08: [io 0x0084-0x0086]
[ 0.125196] pnp 00:08: [io 0x0088]
[ 0.125199] pnp 00:08: [io 0x008c-0x008e]
[ 0.125202] pnp 00:08: [io 0x0090-0x009f]
[ 0.125205] pnp 00:08: [io 0x00a2-0x00bf]
[ 0.125208] pnp 00:08: [io 0x00e0-0x00ef]
[ 0.125212] pnp 00:08: [io 0x0295-0x0296]
[ 0.125215] pnp 00:08: [io 0x03e1-0x03e7]
[ 0.125218] pnp 00:08: [io 0x04d0-0x04d1]
[ 0.125221] pnp 00:08: [io 0x0800-0x087f]
[ 0.125225] pnp 00:08: [io 0x0400-0x041f]
[ 0.125229] pnp 00:08: [io 0x0000-0xffffffff disabled]
[ 0.125268] pnp 00:08: disabling [io 0x0010-0x001f] because it overlaps 0000:00:11.6 BAR 0 [io 0x0000-0x00ff]
[ 0.125274] pnp 00:08: disabling [io 0x0022-0x003f] because it overlaps 0000:00:11.6 BAR 0 [io 0x0000-0x00ff]
[ 0.125279] pnp 00:08: disabling [io 0x0044-0x005f] because it overlaps 0000:00:11.6 BAR 0 [io 0x0000-0x00ff]
[ 0.125283] pnp 00:08: disabling [io 0x0062-0x0063] because it overlaps 0000:00:11.6 BAR 0 [io 0x0000-0x00ff]
[ 0.125288] pnp 00:08: disabling [io 0x0065-0x006f] because it overlaps 0000:00:11.6 BAR 0 [io 0x0000-0x00ff]
[ 0.125293] pnp 00:08: disabling [io 0x0072-0x007f] because it overlaps 0000:00:11.6 BAR 0 [io 0x0000-0x00ff]
[ 0.125297] pnp 00:08: disabling [io 0x0080] because it overlaps 0000:00:11.6 BAR 0 [io 0x0000-0x00ff]
[ 0.125302] pnp 00:08: disabling [io 0x0084-0x0086] because it overlaps 0000:00:11.6 BAR 0 [io 0x0000-0x00ff]
[ 0.125307] pnp 00:08: disabling [io 0x0088] because it overlaps 0000:00:11.6 BAR 0 [io 0x0000-0x00ff]
[ 0.125311] pnp 00:08: disabling [io 0x008c-0x008e] because it overlaps 0000:00:11.6 BAR 0 [io 0x0000-0x00ff]
[ 0.125316] pnp 00:08: disabling [io 0x0090-0x009f] because it overlaps 0000:00:11.6 BAR 0 [io 0x0000-0x00ff]
[ 0.125321] pnp 00:08: disabling [io 0x00a2-0x00bf] because it overlaps 0000:00:11.6 BAR 0 [io 0x0000-0x00ff]
[ 0.125325] pnp 00:08: disabling [io 0x00e0-0x00ef] because it overlaps 0000:00:11.6 BAR 0 [io 0x0000-0x00ff]
[ 0.125409] system 00:08: [io 0x0295-0x0296] has been reserved
[ 0.125415] system 00:08: [io 0x03e1-0x03e7] has been reserved
[ 0.125419] system 00:08: [io 0x04d0-0x04d1] has been reserved
[ 0.125423] system 00:08: [io 0x0800-0x087f] has been reserved
[ 0.125427] system 00:08: [io 0x0400-0x041f] has been reserved
[ 0.125434] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.125551] pnp 00:09: [mem 0xfec00000-0xfec00fff]
[ 0.125555] pnp 00:09: [mem 0xfee00000-0xfee00fff]
[ 0.125559] pnp 00:09: [mem 0xfff80000-0xffffffff]
[ 0.125643] system 00:09: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.125648] system 00:09: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.125653] system 00:09: [mem 0xfff80000-0xffffffff] has been reserved
[ 0.125659] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.125754] pnp 00:0a: [io 0x0060]
[ 0.125758] pnp 00:0a: [io 0x0064]
[ 0.125772] pnp 00:0a: [irq 1]
[ 0.125843] pnp 00:0a: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.125953] pnp 00:0b: [io 0x0000-0xffffffff disabled]
[ 0.125957] pnp 00:0b: [io 0x0680-0x06ff]
[ 0.126053] system 00:0b: [io 0x0680-0x06ff] has been reserved
[ 0.126060] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.126277] pnp 00:0c: [mem 0x00000000-0x0009ffff]
[ 0.126281] pnp 00:0c: [mem 0x000c0000-0x000dffff]
[ 0.126285] pnp 00:0c: [mem 0x000e0000-0x000fffff]
[ 0.126288] pnp 00:0c: [mem 0x00100000-0x3ffeffff]
[ 0.126292] pnp 00:0c: [mem 0x00000000-0xffffffff disabled]
[ 0.126389] system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.126394] system 00:0c: [mem 0x000c0000-0x000dffff] could not be reserved
[ 0.126399] system 00:0c: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.126403] system 00:0c: [mem 0x00100000-0x3ffeffff] could not be reserved
[ 0.126409] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.126669] pnp: PnP ACPI: found 13 devices
[ 0.126673] ACPI: ACPI bus type pnp unregistered
[ 0.126680] PnPBIOS: Disabled by ACPI PNP
[ 0.165285] Switching to clocksource acpi_pm
[ 0.165329] PCI: max bus depth: 1 pci_try_num: 2
[ 0.165356] pci 0000:00:11.6: BAR 0: assigned [io 0x1000-0x10ff]
[ 0.165365] pci 0000:00:11.6: BAR 0: set to [io 0x1000-0x10ff] (PCI address [0x1000-0x10ff])
[ 0.165371] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.165378] pci 0000:00:01.0: bridge window [mem 0xdd900000-0xdfafffff]
[ 0.165384] pci 0000:00:01.0: bridge window [mem 0xcd800000-0xdd7fffff pref]
[ 0.165407] pci 0000:00:01.0: setting latency timer to 64
[ 0.165414] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.165417] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[ 0.165421] pci_bus 0000:01: resource 1 [mem 0xdd900000-0xdfafffff]
[ 0.165425] pci_bus 0000:01: resource 2 [mem 0xcd800000-0xdd7fffff pref]
[ 0.165497] NET: Registered protocol family 2
[ 0.165605] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.166045] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.167115] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.167697] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.167703] TCP reno registered
[ 0.167716] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.167740] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.167930] NET: Registered protocol family 1
[ 0.167963] pci 0000:00:01.0: disabling DAC on VIA PCI bridge
[ 0.167963] pci 0000:00:10.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 0.167963] pci 0000:00:10.0: PCI INT A disabled
[ 0.167963] pci 0000:00:10.1: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 0.167963] pci 0000:00:10.1: PCI INT A disabled
[ 0.167963] pci 0000:00:10.2: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.167963] pci 0000:00:10.2: PCI INT B disabled
[ 0.167963] pci 0000:00:10.3: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.167963] pci 0000:00:10.3: PCI INT B disabled
[ 0.167963] pci 0000:00:10.4: PCI INT C -> GSI 21 (level, low) -> IRQ 21
[ 0.167963] pci 0000:00:10.4: PCI INT C disabled
[ 0.167963] pci 0000:00:11.0: Bypassing VIA 8237 APIC De-Assert Message
[ 0.167963] pci 0000:01:00.0: Boot video device
[ 0.167963] PCI: CLS 64 bytes, default 64
[ 0.167963] audit: initializing netlink socket (disabled)
[ 0.167963] type=2000 audit(1345376145.164:1): initialized
[ 0.198720] Trying to unpack rootfs image as initramfs...
[ 0.240080] highmem bounce pool size: 64 pages
[ 0.240090] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.260437] VFS: Disk quotas dquot_6.5.2
[ 0.260548] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.261601] fuse init (API version 7.17)
[ 0.261834] msgmni has been set to 1702
[ 0.276468] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.276549] io scheduler noop registered
[ 0.276553] io scheduler deadline registered
[ 0.276575] io scheduler cfq registered (default)
[ 0.276821] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.276867] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.277149] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[ 0.277159] ACPI: Power Button [PWRB]
[ 0.277253] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1
[ 0.277260] ACPI: Sleep Button [SLPB]
[ 0.277334] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 0.277340] ACPI: Power Button [PWRF]
[ 0.279909] ERST: Table is not found!
[ 0.279914] GHES: HEST is not enabled!
[ 0.280265] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 0.300710] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.304196] isapnp: Scanning for PnP cards...
[ 0.400633] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.460794] Linux agpgart interface v0.103
[ 0.460908] agpgart: Detected VIA PT800 chipset
[ 0.472248] agpgart-via 0000:00:00.0: AGP aperture is 64M @ 0xe0000000
[ 0.474942] brd: module loaded
[ 0.480742] loop: module loaded
[ 0.481096] pata_acpi 0000:00:0f.1: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.481168] pata_acpi 0000:00:0f.1: PCI INT A disabled
[ 0.481802] Fixed MDIO Bus: probed
[ 0.481849] tun: Universal TUN/TAP device driver, 1.6
[ 0.481852] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.481979] PPP generic driver version 2.4.2
[ 0.482190] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.482235] ehci_hcd 0000:00:10.4: PCI INT C -> GSI 21 (level, low) -> IRQ 21
[ 0.482270] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 0.482364] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
[ 0.482451] ehci_hcd 0000:00:10.4: irq 21, io mem 0xdfe00000
[ 0.492406] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00
[ 0.492748] hub 1-0:1.0: USB hub found
[ 0.492759] hub 1-0:1.0: 8 ports detected
[ 0.492908] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.492939] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.492993] uhci_hcd 0000:00:10.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 0.493009] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 0.493124] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 0.493161] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000eec0
[ 0.493428] hub 2-0:1.0: USB hub found
[ 0.493438] hub 2-0:1.0: 2 ports detected
[ 0.493561] uhci_hcd 0000:00:10.1: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 0.493577] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 0.493688] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 0.493730] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000ef00
[ 0.494003] hub 3-0:1.0: USB hub found
[ 0.494014] hub 3-0:1.0: 2 ports detected
[ 0.494144] uhci_hcd 0000:00:10.2: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.494159] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 0.494270] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[ 0.494305] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000ef20
[ 0.494556] hub 4-0:1.0: USB hub found
[ 0.494566] hub 4-0:1.0: 2 ports detected
[ 0.494688] uhci_hcd 0000:00:10.3: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.494704] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 0.494816] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
[ 0.494850] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000ef40
[ 0.495102] hub 5-0:1.0: USB hub found
[ 0.495112] hub 5-0:1.0: 2 ports detected
[ 0.495322] usbcore: registered new interface driver libusual
[ 0.495405] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 0.495409] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 0.496477] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.500529] mousedev: PS/2 mouse device common for all mice
[ 0.500897] rtc_cmos 00:02: RTC can wake from S4
[ 0.501131] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 0.501197] rtc0: alarms up to one year, y3k, 114 bytes nvram
[ 0.501358] device-mapper: uevent: version 1.0.3
[ 0.501530] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 0.501610] EISA: Probing bus 0 at eisa.0
[ 0.501623] Cannot allocate resource for EISA slot 1
[ 0.501656] EISA: Detected 0 cards.
[ 0.501673] cpufreq-nforce2: No nForce2 chipset.
[ 0.501678] cpuidle: using governor ladder
[ 0.501681] cpuidle: using governor menu
[ 0.501684] EFI Variables Facility v0.08 2004-May-17
[ 0.502052] TCP cubic registered
[ 0.502274] NET: Registered protocol family 10
[ 0.503169] NET: Registered protocol family 17
[ 0.503180] Registering the dns_resolver key type
[ 0.503232] Using IPI No-Shortcut mode
[ 0.506290] PM: Hibernation image not present or could not be loaded.
[ 0.506317] registered taskstats version 1
[ 0.647733] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 0.943698] isapnp: No Plug & Play device found
[ 0.944320] usb 1-3: new high-speed USB device number 3 using ehci_hcd
[ 1.078808] hub 1-3:1.0: USB hub found
[ 1.079344] hub 1-3:1.0: 4 ports detected
[ 1.129718] Freeing initrd memory: 13812k freed
[ 1.163167] Magic number: 8:634:580
[ 1.163240] pci_bus 0000:01: hash matches
[ 1.163318] rtc_cmos 00:02: setting system clock to 2012-08-19 11:35:46 UTC (1345376146)
[ 1.163352] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.163355] EDD information not available.
[ 1.163625] Freeing unused kernel memory: 712k freed
[ 1.164565] Write protecting the kernel text: 5616k
[ 1.164611] Write protecting the kernel read-only data: 2324k
[ 1.196120] Refined TSC clocksource calibration: 2666.580 MHz.
[ 1.196131] Switching to clocksource tsc
[ 1.200124] usb 1-4: new high-speed USB device number 4 using ehci_hcd
[ 1.213553] udevd[80]: starting version 175
[ 1.474943] Floppy drive(s): fd0 is 1.44M
[ 1.495011] sata_via 0000:00:0f.0: version 2.6
[ 1.495036] sata_via 0000:00:0f.0: PCI INT B -> GSI 20 (level, low) -> IRQ 20
[ 1.495101] sata_via 0000:00:0f.0: routed to hard irq line 10
[ 1.503404] FDC 0 is a post-1991 82077
[ 1.516637] scsi0 : sata_via
[ 1.520095] scsi1 : sata_via
[ 1.520243] ata1: SATA max UDMA/133 cmd 0xefa8 ctl 0xefa4 bmdma 0xef80 irq 20
[ 1.520248] ata2: SATA max UDMA/133 cmd 0xef98 ctl 0xefa0 bmdma 0xef88 irq 20
[ 1.520384] pata_via 0000:00:0f.1: version 0.3.4
[ 1.520410] pata_via 0000:00:0f.1: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 1.527590] via_rhine: v1.10-LK1.5.0 2010-10-09 Written by Donald Becker
[ 1.527667] scsi2 : pata_via
[ 1.531645] scsi3 : pata_via
[ 1.535224] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
[ 1.535231] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
[ 1.557585] via-rhine 0000:00:12.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.558453] via-rhine 0000:00:12.0: eth0: VIA Rhine II at 0xdff00000, 00:0e:a6:45:b7:0d, IRQ 23
[ 1.559168] via-rhine 0000:00:12.0: eth0: MII PHY found at address 1, status 0x7849 advertising 01e1 Link 0000
[ 1.708552] ata3.00: ATA-6: WDC WD800JB-00JJC0, 05.01C05, max UDMA/100
[ 1.708559] ata3.00: 156301488 sectors, multi 16: LBA
[ 1.724026] ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 1.738561] ata3.01: HPA detected: current 156299375, native 156301488
[ 1.738568] ata3.01: ATA-7: ST3802110A, 2AAA, max UDMA/100
[ 1.738572] ata3.01: 156299375 sectors, multi 16: LBA48
[ 1.744349] ata3.00: configured for UDMA/100
[ 1.805056] ata3.01: configured for UDMA/100
[ 1.936030] ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 1.947103] scsi 2:0:0:0: Direct-Access ATA WDC WD800JB-00JJ 05.0 PQ: 0 ANSI: 5
[ 1.947799] sd 2:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 1.947902] sd 2:0:0:0: [sda] Write Protect is off
[ 1.947908] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.947951] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.949033] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 1.956259] scsi 2:0:1:0: Direct-Access ATA ST3802110A 2AAA PQ: 0 ANSI: 5
[ 1.956689] sd 2:0:1:0: [sdb] 156299375 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 1.956797] sd 2:0:1:0: [sdb] Write Protect is off
[ 1.956802] sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.956846] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.957653] sd 2:0:1:0: Attached scsi generic sg1 type 0
[ 2.003931] sda: sda1 sda2 < sda5 >
[ 2.004315] sdb:
[ 2.004738] sd 2:0:1:0: [sdb] Attached SCSI disk
[ 2.005362] sd 2:0:0:0: [sda] Attached SCSI disk
[ 2.128407] ata4.01: ATAPI: Optiarc DVD RW AD-7203A, 1.06, max UDMA/66
[ 2.144254] ata4.01: configured for UDMA/66
[ 2.146543] scsi 3:0:1:0: CD-ROM Optiarc DVD RW AD-7203A 1.06 PQ: 0 ANSI: 5
[ 2.149267] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.149275] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.150273] sr 3:0:1:0: Attached scsi CD-ROM sr0
[ 2.150639] sr 3:0:1:0: Attached scsi generic sg2 type 5
[ 2.602223] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 6.572052] usb 2-1: new low-speed USB device number 2 using uhci_hcd
[ 6.824175] usb 1-3.2: new low-speed USB device number 5 using ehci_hcd
[ 6.992203] usb 1-3.3: new high-speed USB device number 6 using ehci_hcd
[ 13.826167] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.903212] udevd[294]: starting version 175
[ 13.937446] Adding 1046524k swap on /dev/sda5. Priority:-1 extents:1 across:1046524k
[ 14.006596] lp: driver loaded but no devices found
[ 14.206756] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 14.386526] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 14.826569] ppdev: user-space parallel port driver
[ 14.846579] Bluetooth: Core ver 2.16
[ 14.850781] NET: Registered protocol family 31
[ 14.850789] Bluetooth: HCI device and connection manager initialized
[ 14.850795] Bluetooth: HCI socket layer initialized
[ 14.850798] Bluetooth: L2CAP socket layer initialized
[ 14.850818] Bluetooth: SCO socket layer initialized
[ 14.864384] parport_pc 00:07: reported by Plug and Play ACPI
[ 14.864516] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 14.891679] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 14.891686] Bluetooth: BNEP filters: protocol multicast
[ 14.933293] Bluetooth: RFCOMM TTY layer initialized
[ 14.933304] Bluetooth: RFCOMM socket layer initialized
[ 14.933307] Bluetooth: RFCOMM ver 1.11
[ 14.960560] lp0: using parport0 (interrupt-driven).
[ 15.036737] wmi: Mapper loaded
[ 15.079431] type=1400 audit(1345376160.409:2): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=501 comm="apparmor_parser"
[ 15.080690] type=1400 audit(1345376160.413:3): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=501 comm="apparmor_parser"
[ 15.253628] [drm] Initialized drm 1.1.0 20060810
[ 15.310011] input: HID compliant-mouse HID compliant-mouse as /devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.0/input/input4
[ 15.311809] generic-usb 0003:1D57:0010.0001: input,hidraw0: USB HID v1.10 Mouse [HID compliant-mouse HID compliant-mouse] on usb-0000:00:10.0-1/input0
[ 15.338026] generic-usb 0003:0FDE:CA01.0002: hiddev0,hidraw1: USB HID v1.10 Device [Universal Bridge] on usb-0000:00:10.4-3.2/input0
[ 15.347741] usbcore: registered new interface driver usbhid
[ 15.347749] usbhid: USB HID core driver
[ 15.515540] type=1400 audit(1345376160.845:4): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=548 comm="apparmor_parser"
[ 15.520740] type=1400 audit(1345376160.853:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=548 comm="apparmor_parser"
[ 15.521113] type=1400 audit(1345376160.853:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=548 comm="apparmor_parser"
[ 15.538535] type=1400 audit(1345376160.869:7): apparmor="STATUS" operation="profile_load" name="/usr/sbin/ntpd" pid=551 comm="apparmor_parser"
[ 15.566453] nouveau 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 15.582939] Linux video capture interface: v2.00
[ 15.628301] uvcvideo: Found UVC 1.00 device HD Webcam C525 (046d:0826)
[ 15.645697] input: HD Webcam C525 as /devices/pci0000:00/0000:00:10.4/usb1/1-3/1-3.3/1-3.3:1.2/input/input5
[ 15.646063] usbcore: registered new interface driver uvcvideo
[ 15.646068] USB Video Class driver (1.1.1)
[ 15.654776] [drm] nouveau 0000:01:00.0: Detected an NV10 generation card (0x011000b2)
[ 15.656837] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from PRAMIN
[ 15.696799] [drm] nouveau 0000:01:00.0: ... appears to be valid
[ 15.696972] [drm] nouveau 0000:01:00.0: BMP BIOS found
[ 15.696976] [drm] nouveau 0000:01:00.0: BMP version 5.20
[ 15.696980] [drm] nouveau 0000:01:00.0: Bios version 03.11.01.30
[ 15.696985] [drm] nouveau 0000:01:00.0: Found Display Configuration Block version 1.4
[ 15.696988] [drm] nouveau 0000:01:00.0: No useful information in BIOS output table; adding all possible outputs
[ 15.761633] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xAB96
[ 15.761655] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xB284
[ 15.761662] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xABB1
[ 15.761681] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xB22B
[ 15.761692] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xAC44
[ 15.761697] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 5 at offset 0xAD98
[ 15.761717] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 6 at offset 0xAC69
[ 15.795675] cfg80211: Calling CRDA to update world regulatory domain
[ 15.817524] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 7 at offset 0xAD33
[ 16.726720] init: failsafe main process (679) killed by TERM signal
[ 17.145521] snd_via82xx_modem 0000:00:11.6: enabling device (0000 -> 0001)
[ 17.145585] snd_via82xx_modem 0000:00:11.6: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[ 17.166704] type=1400 audit(1345376162.497:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=775 comm="apparmor_parser"
[ 17.173228] usbcore: registered new interface driver snd-usb-audio
[ 17.222287] type=1400 audit(1345376162.553:9): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=778 comm="apparmor_parser"
[ 17.232799] type=1400 audit(1345376162.565:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=778 comm="apparmor_parser"
[ 17.233189] type=1400 audit(1345376162.565:11): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=778 comm="apparmor_parser"
[ 17.337162] via-rhine 0000:00:12.0: eth0: link down
[ 17.337367] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 17.342268] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 17.900090] snd_via82xx_modem 0000:00:11.6: setting latency timer to 64
[ 17.956278] rtl8187: inconsistency between id with OEM info!
[ 17.965777] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
[ 17.965785] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[ 17.965789] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
[ 17.965793] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[ 17.965797] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
[ 17.965802] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[ 17.965806] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
[ 17.965810] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[ 17.965813] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
[ 17.965817] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[ 17.965821] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
[ 17.965825] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[ 17.965828] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
[ 17.965832] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[ 17.965835] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[ 17.965839] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[ 17.965842] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[ 17.965846] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[ 17.965849] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[ 17.965853] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[ 17.965856] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[ 17.965860] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[ 17.965864] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
[ 17.965868] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
[ 17.965871] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
[ 17.965875] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
[ 17.965878] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
[ 17.965882] cfg80211: 2474000 KHz - 2494000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
[ 18.037253] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 18.045988] ieee80211 phy0: hwaddr 00:87:11:06:63:18, RTL8187BvB(early) V0 + rtl8225z2, rfkill mask 2
[ 18.240258] rtl8187: Customer ID is 0x00
[ 18.240922] Registered led device: rtl8187-phy0::radio
[ 18.242793] Registered led device: rtl8187-phy0::tx
[ 18.243003] Registered led device: rtl8187-phy0::rx
[ 18.244831] rtl8187: wireless switch is on
[ 18.245085] usbcore: registered new interface driver rtl8187
[ 18.412299] snd_via82xx_modem 0000:00:11.6: PCI INT C disabled
[ 18.412323] snd_via82xx_modem: probe of 0000:00:11.6 failed with error -13
[ 18.412562] snd_via82xx 0000:00:11.5: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[ 18.412735] snd_via82xx 0000:00:11.5: setting latency timer to 64
[ 18.560128] [drm] nouveau 0000:01:00.0: 0 available performance level(s)
[ 18.560144] [drm] nouveau 0000:01:00.0: c: core 199MHz memory 286MHz
[ 18.564373] [TTM] Zone kernel: Available graphics memory: 443162 kiB.
[ 18.564379] [TTM] Zone highmem: Available graphics memory: 512382 kiB.
[ 18.564382] [TTM] Initializing pool allocator.
[ 18.564412] [drm] nouveau 0000:01:00.0: Detected 64MiB VRAM
[ 18.564722] agpgart-via 0000:00:00.0: AGP 3.5 bridge
[ 18.564748] agpgart-via 0000:00:00.0: bridge is in legacy mode, falling back to 2.x
[ 18.564757] agpgart-via 0000:00:00.0: putting AGP V2 device into 4x mode
[ 18.564838] nouveau 0000:01:00.0: putting AGP V2 device into 4x mode
[ 18.564843] [drm] nouveau 0000:01:00.0: 64 MiB GART (aperture)
[ 18.637820] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 18.637826] [drm] No driver support for vblank timestamp query.
[ 18.637838] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on vga encoder (output 0)
[ 18.637843] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on tmds encoder (output 1)
[ 18.754878] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
[ 18.754886] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.754890] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
[ 18.754894] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.754898] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
[ 18.754902] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.754906] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
[ 18.754910] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.754913] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
[ 18.754918] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.754921] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
[ 18.754925] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.754929] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
[ 18.754933] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.754936] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[ 18.754941] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.754944] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[ 18.754948] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.754952] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[ 18.754956] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.754959] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[ 18.754963] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.754967] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
[ 18.754971] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 18.754975] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
[ 18.754979] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 18.754982] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
[ 18.754987] cfg80211: 2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 18.754992] cfg80211: World regulatory domain updated:
[ 18.754994] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 18.754998] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.755002] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 18.755006] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 18.755010] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.755014] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.934651] codec_read: codec 0 is not valid [0xfe0000]
[ 19.000294] codec_read: codec 0 is not valid [0xfe0000]
[ 19.017627] codec_read: codec 0 is not valid [0xfe0000]
[ 19.025673] codec_read: codec 0 is not valid [0xfe0000]
[ 19.249291] [drm] nouveau 0000:01:00.0: allocated 1360x768 fb: 0x48000, bo f3a77200
[ 19.249790] fbcon: nouveaufb (fb0) is primary device
[ 19.256973] Console: switching to colour frame buffer device 170x48
[ 19.257020] fb0: nouveaufb frame buffer device
[ 19.257023] drm: registered panic notifier
[ 19.257044] [drm] Initialized nouveau 0.0.16 20090420 for 0000:01:00.0 on minor 0
[ 20.366500] [drm] nouveau 0000:01:00.0: Setting dpms mode 0 on vga encoder (output 0)
[ 20.366508] [drm] nouveau 0000:01:00.0: Output VGA-1 is running on CRTC 0 using output A
[ 76.052049] usb 1-4: USB disconnect, device number 4
[ 76.064109] rtl8187: wireless radio switch turned off
[ 76.112270] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 79.092047] usb 1-2: new high-speed USB device number 7 using ehci_hcd
[ 84.494772] rtl8187: inconsistency between id with OEM info!
[ 84.499642] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
[ 84.499650] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 84.499653] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
[ 84.499658] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 84.499661] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
[ 84.499665] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 84.499669] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
[ 84.499673] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 84.499676] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
[ 84.499680] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 84.499683] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
[ 84.499687] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 84.499691] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
[ 84.499695] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 84.499698] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[ 84.499702] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 84.499706] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[ 84.499710] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 84.499713] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[ 84.499717] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 84.499720] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[ 84.499724] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 84.499728] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
[ 84.499732] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 84.499735] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
[ 84.499739] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 84.499743] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
[ 84.499747] cfg80211: 2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 84.502063] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 84.505127] ieee80211 phy1: hwaddr 00:87:11:06:63:18, RTL8187BvB(early) V0 + rtl8225z2, rfkill mask 2
[ 84.536803] rtl8187: Customer ID is 0x00
[ 84.536914] Registered led device: rtl8187-phy1::radio
[ 84.536966] Registered led device: rtl8187-phy1::tx
[ 84.537009] Registered led device: rtl8187-phy1::rx
[ 84.537923] rtl8187: wireless switch is on
[ 85.780925] init: plymouth-stop pre-start process (1672) terminated with status 1
[ 88.592841] usb 1-2: USB disconnect, device number 7
[ 88.644262] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 95.956036] usb 1-4: new high-speed USB device number 8 using ehci_hcd
[ 101.395409] rtl8187: inconsistency between id with OEM info!
[ 101.399142] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
[ 101.399150] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 101.399154] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
[ 101.399158] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 101.399162] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
[ 101.399166] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 101.399169] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
[ 101.399173] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 101.399177] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
[ 101.399181] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 101.399184] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
[ 101.399188] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 101.399192] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
[ 101.399196] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 101.399199] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[ 101.399203] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 101.399206] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[ 101.399211] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 101.399214] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[ 101.399218] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 101.399221] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[ 101.399225] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 101.399229] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
[ 101.399233] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 101.399236] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
[ 101.399240] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 101.399244] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
[ 101.399248] cfg80211: 2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 101.402761] ieee80211 phy2: Selected rate control algorithm 'minstrel_ht'
[ 101.407008] ieee80211 phy2: hwaddr 00:87:11:06:63:18, RTL8187BvB(early) V0 + rtl8225z2, rfkill mask 2
[ 101.438439] rtl8187: Customer ID is 0x00
[ 101.438570] Registered led device: rtl8187-phy2::radio
[ 101.438623] Registered led device: rtl8187-phy2::tx
[ 101.438666] Registered led device: rtl8187-phy2::rx
[ 101.439553] rtl8187: wireless switch is on