Πρόβλημα με atheros U98Z062 σε hp dv6

...κάρτες δικτύου, modems, προβλήματα internet
Κανόνες Δ. Συζήτησης
Για την ευκολότερη επίλυση του προβλήματός σας.
Καλό είναι να δημοσιεύσετε τα αποτελέσματα των εντολών στο τερματικό :
lspci -nn
lsusb
rfkill list

Πρόβλημα με atheros U98Z062 σε hp dv6

Δημοσίευσηαπό eval » 11 Ιούλ 2014, 19:42

Καλησπέρα!
Πριν λίγες ημέρες αγόρασα, μεταχειρισμένο (πού λεφτα για καινούριο...) ένα hp pavillion.
Του εγκατέστησα το ubuntu 14.04 64bit (είναι amd 64bit 4Gb ram) και παρόλο που βλέπει τη wlan και τα δίκτυα, όταν πάω να συνδεθώ, δεν είναι εφικτό...Καμιά ιδέα πώς να διορθώσω αυτό το πρόβλημα??????
Ευχαριστώ εκ των προτέρων!!!
Αποτελέσματα από lspci -nn:

Κώδικας: Επιλογή όλων
user@user-HP-Pavilion-dv6-Notebook-PC:~$ lspci -nn
00:00.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] RS880 Host Bridge [1022:9601]
00:02.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] RS780 PCI to PCI bridge (ext gfx port 0) [1022:9603]
00:04.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 0) [1022:9604]
00:05.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 1) [1022:9605]
00:06.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] RS780 PCI to PCI bridge (PCIE port 2) [1022:9606]
00:0a.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 5) [1022:9609]
00:11.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391]
00:12.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397]
00:12.1 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0 USB OHCI1 Controller [1002:4398]
00:12.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396]
00:13.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397]
00:13.1 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0 USB OHCI1 Controller [1002:4398]
00:13.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396]
00:14.0 SMBus [0c05]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller [1002:4385] (rev 3c)
00:14.2 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 Azalia (Intel HDA) [1002:4383]
00:14.3 ISA bridge [0601]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d]
00:14.4 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 PCI to PCI Bridge [1002:4384]
00:18.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor HyperTransport Configuration [1022:1200]
00:18.1 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Address Map [1022:1201]
00:18.2 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor DRAM Controller [1022:1202]
00:18.3 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Miscellaneous Control [1022:1203]
00:18.4 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Link Control [1022:1204]
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] RV710/M92 [Mobility Radeon HD 4530/4570/545v] [1002:9553]
01:00.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] RV710/730 HDMI Audio [Radeon HD 4000 series] [1002:aa38]
08:00.0 Network controller [0280]: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01)
09:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 03)
user@user-HP-Pavilion-dv6-Notebook-PC:~$


Αποτελέσματα lsusb
Κώδικας: Επιλογή όλων
Bus 002 Device 003: ID 15d9:0a4f Trust International B.V.
Bus 002 Device 002: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 5986:0143 Acer, Inc
Bus 001 Device 003: ID 0ace:1215 ZyDAS ZD1211B 802.11g
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

(Το ZyDAS είναι usb wlan)

Αποτελέσματα rfkill list
Κώδικας: Επιλογή όλων
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
1: hp-wifi: Wireless LAN
Soft blocked: no
Hard blocked: no
3: phy2: Wireless LAN
Soft blocked: no
Hard blocked: no
Τελευταία επεξεργασία από the_eye και 12 Ιούλ 2014, 15:19, έχει επεξεργασθεί 1 φορά/ες συνολικά
Αιτία: Τον κώδικα τον βάζουμε σε [code] bbcode
1 Γνώσεις Linux: Πρώτα βήματα ┃ Προγραμματισμού: Πρώτα βήματα ┃ Αγγλικών: Πολύ καλό
2 Ubuntu 14.04 trusty 3.13.0-32-generic 64bit
3 AMD Athlon II Dual-Core M320‖RAM 3950 MiB‖Hewlett-Packard 3636 - HP Pavilion dv6
4 Advanced Micro Devices, Inc. [AMD/ATI] RV710/M92 [Mobility Radeon HD 4530/4570/545v] [1002:9553] {radeon}
5 wlan0: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01) eth0: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 03)
eval
babeTUX
babeTUX
 
Δημοσιεύσεις: 16
Εγγραφή: 11 Ιούλ 2014, 19:18
Εκτύπωση

Re: Πρόβλημα με atheros U98Z062 σε hp dv6

Δημοσίευσηαπό the_eye » 11 Ιούλ 2014, 21:22

Δεν μπορείς να συνδεθείς με καμία από τις 2 κάρτες ;
Κάνε ένα reboot τον router σου.
Όσο λιγότερο κλειστό λογισμικό έχεις, τόσα λιγότερα προβλήματα.
1 Γνώσεις ⇛ Linux: Καλό ┃ Προγραμματισμός: Ναι PHP, MySQL ┃ Αγγλικά: Καλά
2 Ubuntu 24.04.2
3 Intel Core i5-6500 CPU @ 3.20GHz ‖ RAM 7836 MiB ‖ Gigabyte B150M-HD3 DDR3-CF - Gigabyte B150M-HD3 DDR3
4 Intel HD Graphics 530 [8086:1912] {i915}
5 enp1s0: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 15)
Άβαταρ μέλους
the_eye
Διαχειριστής
Διαχειριστής
 
Δημοσιεύσεις: 11719
Εγγραφή: 16 Μαρ 2010, 17:19
Launchpad: ntoulasd
IRC: the_eye_
Εκτύπωση

Re: Πρόβλημα με atheros U98Z062 σε hp dv6

Δημοσίευσηαπό eval » 12 Ιούλ 2014, 03:10

the_eye έγραψε:Δεν μπορείς να συνδεθείς με καμία από τις 2 κάρτες ;
Κάνε ένα reboot τον router σου.


Με την usb wlan συνδέομαι. Του υπολογιστή (atheros) έχει πρόβλημα.
1 Γνώσεις Linux: Πρώτα βήματα ┃ Προγραμματισμού: Πρώτα βήματα ┃ Αγγλικών: Πολύ καλό
2 Ubuntu 14.04 trusty 3.13.0-32-generic 64bit
3 AMD Athlon II Dual-Core M320‖RAM 3950 MiB‖Hewlett-Packard 3636 - HP Pavilion dv6
4 Advanced Micro Devices, Inc. [AMD/ATI] RV710/M92 [Mobility Radeon HD 4530/4570/545v] [1002:9553] {radeon}
5 wlan0: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01) eth0: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 03)
eval
babeTUX
babeTUX
 
Δημοσιεύσεις: 16
Εγγραφή: 11 Ιούλ 2014, 19:18
Εκτύπωση

Re: Πρόβλημα με atheros U98Z062 σε hp dv6

Δημοσίευσηαπό the_eye » 12 Ιούλ 2014, 08:32

Αφού κάνεις μια προσπάθεια σύνδεσης με την atheros δώσε μας το αποτέλεσμα της dmesg.
Όσο λιγότερο κλειστό λογισμικό έχεις, τόσα λιγότερα προβλήματα.
1 Γνώσεις ⇛ Linux: Καλό ┃ Προγραμματισμός: Ναι PHP, MySQL ┃ Αγγλικά: Καλά
2 Ubuntu 24.04.2
3 Intel Core i5-6500 CPU @ 3.20GHz ‖ RAM 7836 MiB ‖ Gigabyte B150M-HD3 DDR3-CF - Gigabyte B150M-HD3 DDR3
4 Intel HD Graphics 530 [8086:1912] {i915}
5 enp1s0: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 15)
Άβαταρ μέλους
the_eye
Διαχειριστής
Διαχειριστής
 
Δημοσιεύσεις: 11719
Εγγραφή: 16 Μαρ 2010, 17:19
Launchpad: ntoulasd
IRC: the_eye_
Εκτύπωση

Re: Πρόβλημα με atheros U98Z062 σε hp dv6

Δημοσίευσηαπό eval » 12 Ιούλ 2014, 11:17

Μου βγάζει τα παρακάτω:
Κώδικας: Επιλογή όλων
[ 1.451456] usb usb6: Product: OHCI PCI host controller
[ 1.451458] usb usb6: Manufacturer: Linux 3.13.0-32-generic ohci_hcd
[ 1.451460] usb usb6: SerialNumber: 0000:00:13.1
[ 1.451653] hub 6-0:1.0: USB hub found
[ 1.451728] hub 6-0:1.0: 3 ports detected
[ 1.451887] ohci-platform: OHCI generic platform driver
[ 1.451902] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.452039] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.478729] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.478743] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.479010] mousedev: PS/2 mouse device common for all mice
[ 1.479936] rtc_cmos 00:04: RTC can wake from S4
[ 1.480200] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 1.480228] rtc_cmos 00:04: alarms up to one day, 114 bytes nvram, hpet irqs
[ 1.480318] device-mapper: uevent: version 1.0.3
[ 1.480596] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[ 1.480605] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.480720] TCP: cubic registered
[ 1.480823] NET: Registered protocol family 10
[ 1.481025] NET: Registered protocol family 17
[ 1.481036] Key type dns_resolver registered
[ 1.481501] Loading compiled-in X.509 certificates
[ 1.482818] Loaded X.509 cert 'Magrathea: Glacier signing key: 2f256a303498047a90baa7f97bed7b018776bf18'
[ 1.482831] registered taskstats version 1
[ 1.486131] Key type trusted registered
[ 1.489024] Key type encrypted registered
[ 1.491956] AppArmor: AppArmor sha1 policy hashing enabled
[ 1.491962] IMA: No TPM chip found, activating TPM-bypass!
[ 1.492282] regulator-dummy: disabling
[ 1.492446] Magic number: 6:817:118
[ 1.492634] rtc_cmos 00:04: setting system clock to 2014-07-12 08:08:42 UTC (1405152522)
[ 1.492755] acpi-cpufreq: overriding BIOS provided _PSD data
[ 1.492864] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.492865] EDD information not available.
[ 1.492913] PM: Hibernation image not present or could not be loaded.
[ 1.494725] Freeing unused kernel memory: 1336K (ffffffff81d1f000 - ffffffff81e6d000)
[ 1.494729] Write protecting the kernel read-only data: 12288k
[ 1.497807] Freeing unused kernel memory: 816K (ffff880001734000 - ffff880001800000)
[ 1.500444] Freeing unused kernel memory: 696K (ffff880001b52000 - ffff880001c00000)
[ 1.509411] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 1.511683] usb 1-3: new high-speed USB device number 2 using ehci-pci
[ 1.531253] systemd-udevd[97]: starting version 204
[ 1.591062] ahci 0000:00:11.0: version 3.0
[ 1.591406] ahci 0000:00:11.0: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
[ 1.591411] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc sxs
[ 1.591946] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.591964] r8169 0000:09:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 1.592479] r8169 0000:09:00.0: irq 45 for MSI/MSI-X
[ 1.592682] r8169 0000:09:00.0 eth0: RTL8168d/8111d at 0xffffc9000067c000, 00:26:9e:f5:28:40, XID 081000c0 IRQ 45
[ 1.592685] r8169 0000:09:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 1.604083] scsi0 : ahci
[ 1.604237] scsi1 : ahci
[ 1.606193] scsi2 : ahci
[ 1.606305] ata1: SATA max UDMA/133 abar m1024@0xf2408000 port 0xf2408100 irq 22
[ 1.606309] ata2: SATA max UDMA/133 abar m1024@0xf2408000 port 0xf2408180 irq 22
[ 1.606313] ata3: SATA max UDMA/133 abar m1024@0xf2408000 port 0xf2408200 irq 22
[ 1.909666] usb 1-3: New USB device found, idVendor=5986, idProduct=0143
[ 1.909672] usb 1-3: New USB device strings: Mfr=3, Product=1, SerialNumber=0
[ 1.909674] usb 1-3: Product: HP Webcam
[ 1.909677] usb 1-3: Manufacturer: Bison Electronics Inc.
[ 1.931616] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.035678] usb 2-3: new high-speed USB device number 2 using ehci-pci
[ 2.095658] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.097393] ata1.00: ATA-8: FUJITSU MJA2500BH G2, 00400018, max UDMA/100
[ 2.097398] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 2.099418] ata1.00: configured for UDMA/100
[ 2.099580] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.099832] scsi 0:0:0:0: Direct-Access ATA FUJITSU MJA2500B 0040 PQ: 0 ANSI: 5
[ 2.100048] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.100142] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 2.100246] sd 0:0:0:0: [sda] Write Protect is off
[ 2.100249] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.100295] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.111573] ata2.00: ATAPI: hp DVD RW AD-7586H, KH03, max UDMA/100
[ 2.111591] tsc: Refined TSC clocksource calibration: 2094.750 MHz
[ 2.124622] ata2.00: configured for UDMA/100
[ 2.129768] scsi 1:0:0:0: CD-ROM hp DVD RW AD-7586H KH03 PQ: 0 ANSI: 5
[ 2.138930] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.138935] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.139088] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.139149] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 2.154908] sda: sda1 sda2 < sda5 >
[ 2.155546] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.168308] usb 2-3: New USB device found, idVendor=1a40, idProduct=0101
[ 2.168314] usb 2-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.168316] usb 2-3: Product: USB 2.0 Hub
[ 2.168549] hub 2-3:1.0: USB hub found
[ 2.168647] hub 2-3:1.0: 4 ports detected
[ 2.455830] usb 2-3.2: new low-speed USB device number 3 using ehci-pci
[ 2.540094] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 2.572403] usb 2-3.2: New USB device found, idVendor=15d9, idProduct=0a4f
[ 2.572409] usb 2-3.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.572411] usb 2-3.2: Product: USB OPTICAL MOUSE
[ 2.763835] psmouse serio1: synaptics: Touchpad model: 1, fw: 6.5, id: 0x1c0b1, caps: 0xa04751/0xa00000/0x0, board id: 3655, fw id: 428212
[ 2.857094] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
[ 3.112067] Switched to clocksource tsc
[ 3.471717] random: init urandom read with 114 bits of entropy available
[ 3.679663] random: nonblocking pool is initialized
[ 4.277089] init: plymouth-upstart-bridge main process (157) terminated with status 1
[ 4.277111] init: plymouth-upstart-bridge main process ended, respawning
[ 4.281825] init: plymouth-upstart-bridge main process (169) terminated with status 1
[ 4.281842] init: plymouth-upstart-bridge main process ended, respawning
[ 4.285093] init: plymouth-upstart-bridge main process (171) terminated with status 1
[ 4.285111] init: plymouth-upstart-bridge main process ended, respawning
[ 4.289833] init: plymouth-upstart-bridge main process (172) terminated with status 1
[ 4.289850] init: plymouth-upstart-bridge main process ended, respawning
[ 4.293592] init: plymouth-upstart-bridge main process (174) terminated with status 1
[ 4.293608] init: plymouth-upstart-bridge main process ended, respawning
[ 4.298396] init: plymouth-upstart-bridge main process (175) terminated with status 1
[ 4.298412] init: plymouth-upstart-bridge main process ended, respawning
[ 4.301651] init: plymouth-upstart-bridge main process (177) terminated with status 1
[ 4.301671] init: plymouth-upstart-bridge main process ended, respawning
[ 4.306880] init: plymouth-upstart-bridge main process (178) terminated with status 1
[ 4.306896] init: plymouth-upstart-bridge main process ended, respawning
[ 4.310912] init: plymouth-upstart-bridge main process (180) terminated with status 1
[ 4.310931] init: plymouth-upstart-bridge main process ended, respawning
[ 4.316131] init: plymouth-upstart-bridge main process (181) terminated with status 1
[ 4.316148] init: plymouth-upstart-bridge main process ended, respawning
[ 4.319476] init: plymouth-upstart-bridge main process (183) terminated with status 1
[ 4.319494] init: plymouth-upstart-bridge respawning too fast, stopped
[ 12.290693] Adding 4188156k swap on /dev/sda5. Priority:-1 extents:1 across:4188156k FS
[ 12.337654] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 12.426020] systemd-udevd[284]: starting version 204
[ 12.584345] lp: driver loaded but no devices found
[ 12.610490] ppdev: user-space parallel port driver
[ 12.628419] [drm] Initialized drm 1.1.0 20060810
[ 12.655545] ACPI: Video Device [DVGA] (multi-head: yes rom: no post: no)
[ 12.700746] hp_accel: laptop model unknown, using default axes configuration
[ 12.705180] [drm] radeon kernel modesetting enabled.
[ 12.707568] checking generic (e0000000 300000) vs hw (e0000000 10000000)
[ 12.707573] fb: conflicting fb hw usage radeondrmfb vs VESA VGA - removing generic driver
[ 12.707598] Console: switching to colour dummy device 80x25
[ 12.707674] lis3lv02d: 8 bits sensor found
[ 12.712821] [drm] initializing kernel modesetting (RV710 0x1002:0x9553 0x103C:0x3636).
[ 12.712844] [drm] register mmio base: 0xF2300000
[ 12.712845] [drm] register mmio size: 65536
[ 12.715884] ATOM BIOS: BR34651.001
[ 12.715942] radeon 0000:01:00.0: VRAM: 512M 0x0000000000000000 - 0x000000001FFFFFFF (512M used)
[ 12.715945] radeon 0000:01:00.0: GTT: 1024M 0x0000000020000000 - 0x000000005FFFFFFF
[ 12.715948] [drm] Detected VRAM RAM=512M, BAR=256M
[ 12.715949] [drm] RAM width 64bits DDR
[ 12.717063] [TTM] Zone kernel: Available graphics memory: 2022622 kiB
[ 12.717067] [TTM] Initializing pool allocator
[ 12.717072] [TTM] Initializing DMA pool allocator
[ 12.717100] [drm] radeon: 512M of VRAM memory ready
[ 12.717103] [drm] radeon: 1024M of GTT memory ready.
[ 12.717140] [drm] Loading RV710 Microcode
[ 12.720888] acpi device:0a: registered as cooling_device2
[ 12.721002] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:07/LNXVIDEO:01/input/input7
[ 12.723845] ene_ir: chip is 0x3926 - kbver = 0x00, rev = 0xd2
[ 12.723850] ene_ir: PLL freq = 1406
[ 12.723852] ene_ir: KB3926D or higher detected
[ 12.723864] ene_ir: Firmware regs: 00 00
[ 12.723865] ene_ir: Hardware features:
[ 12.723867] ene_ir: * Uses GPIO 40 for IR demodulated input
[ 12.755412] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input9
[ 12.756463] wmi: Mapper loaded
[ 12.767039] Registered IR keymap rc-rc6-mce
[ 12.767233] input: ENE eHome Infrared Remote Receiver as /devices/virtual/rc/rc0/input8
[ 12.767411] rc0: ENE eHome Infrared Remote Receiver as /devices/virtual/rc/rc0
[ 12.775141] IR NEC protocol handler initialized
[ 12.816711] IR RC5(x) protocol handler initialized
[ 12.817055] cfg80211: Calling CRDA to update world regulatory domain
[ 12.817943] IR RC6 protocol handler initialized
[ 12.818182] IR Sony protocol handler initialized
[ 12.818270] IR JVC protocol handler initialized
[ 12.818530] IR SANYO protocol handler initialized
[ 12.818545] IR MCE Keyboard/mouse protocol handler initialized
[ 12.819043] lirc_dev: IR Remote Control driver registered, major 251
[ 12.820691] IR LIRC bridge handler initialized
[ 12.821455] ACPI Warning: 0x0000000000000b00-0x0000000000000b07 SystemIO conflicts with Region \_SB_.PCI0.SMBS.SMBI 1 (20131115/utaddress-251)
[ 12.821463] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 12.823190] input: MCE IR Keyboard/Mouse (ene_ir) as /devices/virtual/input/input10
[ 12.823386] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05
[ 12.823448] sp5100_tco: PCI Revision ID: 0x3c
[ 12.823497] sp5100_tco: failed to find MMIO address, giving up.
[ 12.829714] MCE: In-kernel MCE decoding enabled.
[ 12.833467] rc rc0: lirc_dev: driver ir-lirc-codec (ene_ir) registered at minor = 0
[ 12.833494] ene_ir: driver has been successfully loaded
[ 12.834365] EDAC MC: Ver: 3.0.0
[ 12.841873] AMD64 EDAC driver v3.4.0
[ 12.841914] EDAC amd64: DRAM ECC disabled.
[ 12.841920] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
[ 12.841920] Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
[ 12.841920] (Note that use of the override may cause unknown side effects.)
[ 12.900752] hda-intel 0000:00:14.2: Using LPIB position fix
[ 12.912054] hda-intel 0000:00:14.2: Enable sync_write for stable communication
[ 12.921285] mute LED gpio 8 polarity 1
[ 12.921510] autoconfig: line_outs=1 (0xf/0x0/0x0/0x0/0x0) type:line
[ 12.921512] speaker_outs=1 (0xd/0x0/0x0/0x0/0x0)
[ 12.921514] hp_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 12.921515] mono: mono_out=0x0
[ 12.921517] dig-out=0x1e/0x0
[ 12.921527] inputs:
[ 12.921529] Internal Mic=0x18
[ 12.921531] Mic=0xb
[ 12.946408] kvm: disabled by bios
[ 12.954364] input: HDA ATI SB Front Line Out as /devices/pci0000:00/0000:00:14.2/sound/card0/input12
[ 12.973797] ath: phy0: Enable LNA combining
[ 12.974520] input: HDA ATI SB Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input11
[ 12.977617] ath: phy0: ASPM enabled: 0x43
[ 12.977624] ath: EEPROM regdomain: 0x6a
[ 12.977626] ath: EEPROM indicates we should expect a direct regpair map
[ 12.977629] ath: Country alpha2 being used: 00
[ 12.977630] ath: Regpair used: 0x6a
[ 13.001937] type=1400 audit(1405152533.999:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=361 comm="apparmor_parser"
[ 13.001947] type=1400 audit(1405152533.999:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=361 comm="apparmor_parser"
[ 13.001953] type=1400 audit(1405152533.999:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=361 comm="apparmor_parser"
[ 13.002548] type=1400 audit(1405152533.999:5): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=361 comm="apparmor_parser"
[ 13.002554] type=1400 audit(1405152533.999:6): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=361 comm="apparmor_parser"
[ 13.002858] type=1400 audit(1405152533.999:7): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=361 comm="apparmor_parser"
[ 13.038915] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 13.039375] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xffffc900017c0000, irq=17
[ 13.155247] input: HP WMI hotkeys as /devices/virtual/input/input13
[ 13.448075] cfg80211: World regulatory domain updated:
[ 13.448081] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.448084] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.448086] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.448088] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.448090] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.448091] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.471826] [drm] GART: num cpu pages 262144, num gpu pages 262144
[ 13.473970] [drm] enabling PCIE gen 2 link speeds, disable with radeon.pcie_gen2=0
[ 13.477218] [drm] PCIE GART of 1024M enabled (table at 0x000000000025D000).
[ 13.477272] radeon 0000:01:00.0: WB enabled
[ 13.477277] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000020000c00 and cpu addr 0xffff8800cea40c00
[ 13.477280] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000020000c0c and cpu addr 0xffff8800cea40c0c
[ 13.478202] radeon 0000:01:00.0: fence driver on ring 5 use gpu addr 0x000000000005c598 and cpu addr 0xffffc9000191c598
[ 13.478205] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 13.478206] [drm] Driver supports precise vblank timestamp query.
[ 13.478235] radeon 0000:01:00.0: irq 46 for MSI/MSI-X
[ 13.478252] radeon 0000:01:00.0: radeon: using MSI.
[ 13.478283] [drm] radeon: irq initialized.
[ 13.524257] [drm] ring test on 0 succeeded in 1 usecs
[ 13.524316] [drm] ring test on 3 succeeded in 1 usecs
[ 13.718886] [drm] ring test on 5 succeeded in 1 usecs
[ 13.718891] [drm] UVD initialized successfully.
[ 13.718999] [drm] Enabling audio 0 support
[ 13.719023] [drm] ib test on ring 0 succeeded in 0 usecs
[ 13.719044] [drm] ib test on ring 3 succeeded in 0 usecs
[ 13.744735] hidraw: raw HID events driver (C) Jiri Kosina
[ 13.747419] Linux video capture interface: v2.00
[ 13.761335] usbcore: registered new interface driver usbhid
[ 13.761340] usbhid: USB HID core driver
[ 13.772935] input: USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:13.2/usb2/2-3/2-3.2/2-3.2:1.0/input/input14
[ 13.778022] hid-generic 0003:15D9:0A4F.0001: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:00:13.2-3.2/input0
[ 13.784152] uvcvideo: Found UVC 1.00 device HP Webcam (5986:0143)
[ 13.789574] input: HP Webcam as /devices/pci0000:00/0000:00:12.2/usb1/1-3/1-3:1.0/input/input15
[ 13.790897] usbcore: registered new interface driver uvcvideo
[ 13.790902] USB Video Class driver (1.1.1)
[ 13.878546] [drm] ib test on ring 5 succeeded
[ 13.878997] [drm] radeon atom DIG backlight initialized
[ 13.878999] [drm] Radeon Display Connectors
[ 13.879001] [drm] Connector 0:
[ 13.879002] [drm] LVDS-1
[ 13.879004] [drm] DDC: 0x7f68 0x7f68 0x7f6c 0x7f6c 0x7f70 0x7f70 0x7f74 0x7f74
[ 13.879005] [drm] Encoders:
[ 13.879006] [drm] LCD1: INTERNAL_UNIPHY2
[ 13.879008] [drm] Connector 1:
[ 13.879009] [drm] VGA-1
[ 13.879011] [drm] DDC: 0x7fa0 0x7fa0 0x7fa4 0x7fa4 0x7fa8 0x7fa8 0x7fac 0x7fac
[ 13.879012] [drm] Encoders:
[ 13.879013] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 13.879014] [drm] Connector 2:
[ 13.879015] [drm] HDMI-A-1
[ 13.879016] [drm] HPD1
[ 13.879018] [drm] DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c 0x7e4c
[ 13.879019] [drm] Encoders:
[ 13.879020] [drm] DFP1: INTERNAL_UNIPHY
[ 13.884379] [drm] radeon: dpm initialized
[ 14.404697] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 14.627124] init: failsafe main process (574) killed by TERM signal
[ 14.880726] [drm] fb mappable at 0xE045E000
[ 14.880731] [drm] vram apper at 0xE0000000
[ 14.880733] [drm] size 4325376
[ 14.880735] [drm] fb depth is 24
[ 14.880736] [drm] pitch is 5632
[ 14.880922] fbcon: radeondrmfb (fb0) is primary device
[ 14.887499] type=1400 audit(1405152535.883:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=655 comm="apparmor_parser"
[ 14.887506] type=1400 audit(1405152535.883:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd" pid=655 comm="apparmor_parser"
[ 14.888108] type=1400 audit(1405152535.887:10): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=655 comm="apparmor_parser"
[ 15.078777] type=1400 audit(1405152536.075:11): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=691 comm="apparmor_parser"
[ 15.254636] init: cups main process (658) killed by HUP signal
[ 15.254649] init: cups main process ended, respawning
[ 15.333365] Console: switching to colour frame buffer device 170x48
[ 15.337679] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[ 15.337682] radeon 0000:01:00.0: registered panic notifier
[ 15.337706] [drm] Initialized radeon 2.36.0 20080528 for 0000:01:00.0 on minor 0
[ 15.337892] hda-intel 0000:01:00.1: Handle VGA-switcheroo audio client
[ 15.337894] hda-intel 0000:01:00.1: Using LPIB position fix
[ 15.337945] snd_hda_intel 0000:01:00.1: irq 47 for MSI/MSI-X
[ 15.340748] hda-intel 0000:01:00.1: Enable sync_write for stable communication
[ 15.351612] HDMI ATI/AMD: no speaker allocation for ELD
[ 15.352630] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input16
[ 15.484339] Bluetooth: Core ver 2.17
[ 15.484788] NET: Registered protocol family 31
[ 15.484791] Bluetooth: HCI device and connection manager initialized
[ 15.484803] Bluetooth: HCI socket layer initialized
[ 15.484806] Bluetooth: L2CAP socket layer initialized
[ 15.484813] Bluetooth: SCO socket layer initialized
[ 15.490137] Bluetooth: RFCOMM TTY layer initialized
[ 15.490152] Bluetooth: RFCOMM socket layer initialized
[ 15.490159] Bluetooth: RFCOMM ver 1.11
[ 15.768886] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 15.768891] Bluetooth: BNEP filters: protocol multicast
[ 15.768903] Bluetooth: BNEP socket layer initialized
[ 16.536312] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 16.539608] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 16.678008] r8169 0000:09:00.0 eth0: link down
[ 16.678096] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.679148] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 36.918099] wlan0: authenticate with 54:22:f8:09:54:e2
[ 36.940249] wlan0: send auth to 54:22:f8:09:54:e2 (try 1/3)
[ 36.944143] wlan0: authenticated
[ 36.946896] wlan0: associate with 54:22:f8:09:54:e2 (try 1/3)
[ 36.953699] wlan0: RX AssocResp from 54:22:f8:09:54:e2 (capab=0x411 status=0 aid=2)
[ 36.953755] wlan0: associated
[ 36.953797] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 45.018152] audit_printk_skb: 150 callbacks suppressed
[ 45.018158] type=1400 audit(1405152566.007:62): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=2191 comm="apparmor_parser"
[ 45.018167] type=1400 audit(1405152566.007:63): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2191 comm="apparmor_parser"
[ 45.018752] type=1400 audit(1405152566.007:64): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2191 comm="apparmor_parser"
[ 78.530241] wlan0: deauthenticating from 54:22:f8:09:54:e2 by local choice (reason=3)
[ 78.541575] cfg80211: Calling CRDA to update world regulatory domain
[ 78.546879] cfg80211: World regulatory domain updated:
[ 78.546885] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 78.546888] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 78.546890] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 78.546892] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 78.546894] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 78.546896] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 83.034887] wlan0: authenticate with 54:22:f8:09:54:e2
[ 83.058878] wlan0: send auth to 54:22:f8:09:54:e2 (try 1/3)
[ 83.062152] wlan0: authenticated
[ 83.066013] wlan0: associate with 54:22:f8:09:54:e2 (try 1/3)
[ 83.075273] wlan0: RX AssocResp from 54:22:f8:09:54:e2 (capab=0x411 status=0 aid=2)
[ 83.075391] wlan0: associated
[ 83.091799] wlan0: deauthenticating from 54:22:f8:09:54:e2 by local choice (reason=2)
[ 83.107743] cfg80211: Calling CRDA to update world regulatory domain
[ 83.108004] wlan0: authenticate with 54:22:f8:09:54:e2
[ 83.125793] wlan0: send auth to 54:22:f8:09:54:e2 (try 1/3)
[ 83.126869] cfg80211: World regulatory domain updated:
[ 83.126876] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 83.126879] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 83.126881] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 83.126883] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 83.126885] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 83.126886] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 83.136163] wlan0: authenticated
[ 83.138054] wlan0: associate with 54:22:f8:09:54:e2 (try 1/3)
[ 83.202914] wlan0: RX AssocResp from 54:22:f8:09:54:e2 (capab=0x411 status=0 aid=2)
[ 83.203001] wlan0: associated
[ 304.382348] wlan0: deauthenticating from 54:22:f8:09:54:e2 by local choice (reason=3)
[ 305.026557] cfg80211: Calling CRDA to update world regulatory domain
[ 305.041327] cfg80211: World regulatory domain updated:
[ 305.041333] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 305.041336] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 305.041339] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 305.041340] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 305.041342] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 305.041344] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 306.885217] wlan0: authenticate with 54:22:f8:09:54:e2
[ 306.918650] wlan0: send auth to 54:22:f8:09:54:e2 (try 1/3)
[ 307.083759] wlan0: send auth to 54:22:f8:09:54:e2 (try 2/3)
[ 307.198807] wlan0: send auth to 54:22:f8:09:54:e2 (try 3/3)
[ 307.321734] wlan0: authentication with 54:22:f8:09:54:e2 timed out
[ 319.991102] wlan0: authenticate with 54:22:f8:09:54:e2
[ 320.014294] wlan0: direct probe to 54:22:f8:09:54:e2 (try 1/3)
[ 320.217973] wlan0: direct probe to 54:22:f8:09:54:e2 (try 2/3)
[ 320.421957] wlan0: direct probe to 54:22:f8:09:54:e2 (try 3/3)
[ 320.626240] wlan0: authentication with 54:22:f8:09:54:e2 timed out
[ 321.995458] wlan0: authenticate with 54:22:f8:09:54:e2
[ 322.018512] wlan0: direct probe to 54:22:f8:09:54:e2 (try 1/3)
[ 322.222776] wlan0: direct probe to 54:22:f8:09:54:e2 (try 2/3)
[ 322.426601] wlan0: direct probe to 54:22:f8:09:54:e2 (try 3/3)
[ 322.630665] wlan0: authentication with 54:22:f8:09:54:e2 timed out
[ 324.492255] wlan0: authenticate with 54:22:f8:09:54:e2
[ 324.515311] wlan0: direct probe to 54:22:f8:09:54:e2 (try 1/3)
[ 324.719519] wlan0: direct probe to 54:22:f8:09:54:e2 (try 2/3)
[ 324.923570] wlan0: direct probe to 54:22:f8:09:54:e2 (try 3/3)
[ 325.127656] wlan0: authentication with 54:22:f8:09:54:e2 timed out
[ 335.322823] wlan0: authenticate with 54:22:f8:09:54:e2
[ 335.348057] wlan0: direct probe to 54:22:f8:09:54:e2 (try 1/3)
[ 335.551002] wlan0: direct probe to 54:22:f8:09:54:e2 (try 2/3)
[ 335.755093] wlan0: direct probe to 54:22:f8:09:54:e2 (try 3/3)
[ 335.958989] wlan0: authentication with 54:22:f8:09:54:e2 timed out
user@user-HP-Pavilion-dv6-Notebook-PC:~$
Τελευταία επεξεργασία από the_eye και 12 Ιούλ 2014, 15:18, έχει επεξεργασθεί 1 φορά/ες συνολικά
Αιτία: Τον κώδικα τον βάζουμε σε [code] bbcode
1 Γνώσεις Linux: Πρώτα βήματα ┃ Προγραμματισμού: Πρώτα βήματα ┃ Αγγλικών: Πολύ καλό
2 Ubuntu 14.04 trusty 3.13.0-32-generic 64bit
3 AMD Athlon II Dual-Core M320‖RAM 3950 MiB‖Hewlett-Packard 3636 - HP Pavilion dv6
4 Advanced Micro Devices, Inc. [AMD/ATI] RV710/M92 [Mobility Radeon HD 4530/4570/545v] [1002:9553] {radeon}
5 wlan0: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01) eth0: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 03)
eval
babeTUX
babeTUX
 
Δημοσιεύσεις: 16
Εγγραφή: 11 Ιούλ 2014, 19:18
Εκτύπωση

Re: Πρόβλημα με atheros U98Z062 σε hp dv6

Δημοσίευσηαπό the_eye » 13 Ιούλ 2014, 13:59


!

Μήνυμα ενημέρωσης προς τον/την eval

Σε παρακαλούμε να διαβάσεις τις οδηγίες προς νεοεισερχόμενους προσεκτικά. Είναι σημαντική η προσάρτηση της υπογραφής με τα χαρακτηριστικά του υπολογιστή σου hardware id (πχ [10ec:8168]), έτσι ώστε να δίνονται συγκεκριμένες πληροφορίες όταν πρόκειται για επίλυση ενός προβλήματός σου. Οι αλλαγές μπορούν να γίνουν από τον πίνακα ελέγχου αλλά και με το αυτόματο script που θα το βρεις παρακάτω.
Αυτόματο script υπογραφής


Για δοκίμασε το παρακάτω. Δώσε σε τερματικό
Κώδικας: Επιλογή όλων
gksudo /etc/modprobe.d/ath9k.conf


Βάλε στον κειμενογράφο την παρακάτω γραμμή, αποθήκευσε και κάνε επανεκκίνηση.
Κώδικας: Επιλογή όλων
options atk9k nohwcrypt=1
Όσο λιγότερο κλειστό λογισμικό έχεις, τόσα λιγότερα προβλήματα.
1 Γνώσεις ⇛ Linux: Καλό ┃ Προγραμματισμός: Ναι PHP, MySQL ┃ Αγγλικά: Καλά
2 Ubuntu 24.04.2
3 Intel Core i5-6500 CPU @ 3.20GHz ‖ RAM 7836 MiB ‖ Gigabyte B150M-HD3 DDR3-CF - Gigabyte B150M-HD3 DDR3
4 Intel HD Graphics 530 [8086:1912] {i915}
5 enp1s0: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 15)
Άβαταρ μέλους
the_eye
Διαχειριστής
Διαχειριστής
 
Δημοσιεύσεις: 11719
Εγγραφή: 16 Μαρ 2010, 17:19
Launchpad: ntoulasd
IRC: the_eye_
Εκτύπωση

Re: Πρόβλημα με atheros U98Z062 σε hp dv6

Δημοσίευσηαπό eval » 24 Ιούλ 2014, 02:34

Δε μου ανοίγει κάποιο κειμενογράφο όταν βάζω στο τερματικό την εντολή gksudo /etc/modprobe.d/ath9k.conf
Δε θα έπρεπε να ανοίγει ο κειμενογράφος για να προσθέσω το options atk9k nohwcrypt=1 ?
1 Γνώσεις Linux: Πρώτα βήματα ┃ Προγραμματισμού: Πρώτα βήματα ┃ Αγγλικών: Πολύ καλό
2 Ubuntu 14.04 trusty 3.13.0-32-generic 64bit
3 AMD Athlon II Dual-Core M320‖RAM 3950 MiB‖Hewlett-Packard 3636 - HP Pavilion dv6
4 Advanced Micro Devices, Inc. [AMD/ATI] RV710/M92 [Mobility Radeon HD 4530/4570/545v] [1002:9553] {radeon}
5 wlan0: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01) eth0: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 03)
eval
babeTUX
babeTUX
 
Δημοσιεύσεις: 16
Εγγραφή: 11 Ιούλ 2014, 19:18
Εκτύπωση

Re: Πρόβλημα με atheros U98Z062 σε hp dv6

Δημοσίευσηαπό Logan » 24 Ιούλ 2014, 02:48

eval έγραψε:Δε μου ανοίγει κάποιο κειμενογράφο όταν βάζω στο τερματικό την εντολή gksudo /etc/modprobe.d/ath9k.conf
Δε θα έπρεπε να ανοίγει ο κειμενογράφος για να προσθέσω το options atk9k nohwcrypt=1 ?

Κάνε το έτσι :
Κώδικας: Επιλογή όλων
gksudo gedit /etc/modprobe.d/ath9k.conf

είναι τυπογραφικό.
1 Γνώσεις Linux: όχι και μιάου! ┃ Προγραμματισμού:Ε.. ┃ Αγγλικών: Μέτρια
2 Arch Linux Gnome 4χχ
3 Intel Core i5-3210M CPU @ 2.50GHz ‖ RAM 7.7 GiB |
4 Intel 3rd Gen Core processor Graphics Controller [8086:0166] {i915} ⋮ Advanced Micro Devices, Inc. [AMD/ATI] Thames [Radeon HD 7500M/7600M Series] [1002:6840] {radeon}
Refugees Welcome
Άβαταρ μέλους
Logan
daemonTUX
daemonTUX
 
Δημοσιεύσεις: 816
Εγγραφή: 25 Νοέμ 2013, 19:42
Launchpad: loganlettuce
IRC: LoganL
Εκτύπωση

Re: Πρόβλημα με atheros U98Z062 σε hp dv6

Δημοσίευσηαπό the_eye » 24 Ιούλ 2014, 08:47

Ναι, ξέχασα το gedit
Όσο λιγότερο κλειστό λογισμικό έχεις, τόσα λιγότερα προβλήματα.
1 Γνώσεις ⇛ Linux: Καλό ┃ Προγραμματισμός: Ναι PHP, MySQL ┃ Αγγλικά: Καλά
2 Ubuntu 24.04.2
3 Intel Core i5-6500 CPU @ 3.20GHz ‖ RAM 7836 MiB ‖ Gigabyte B150M-HD3 DDR3-CF - Gigabyte B150M-HD3 DDR3
4 Intel HD Graphics 530 [8086:1912] {i915}
5 enp1s0: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 15)
Άβαταρ μέλους
the_eye
Διαχειριστής
Διαχειριστής
 
Δημοσιεύσεις: 11719
Εγγραφή: 16 Μαρ 2010, 17:19
Launchpad: ntoulasd
IRC: the_eye_
Εκτύπωση

Re: Πρόβλημα με atheros U98Z062 σε hp dv6

Δημοσίευσηαπό eval » 25 Ιούλ 2014, 17:45

Τίποτα....Δε συνδέεται...
1 Γνώσεις Linux: Πρώτα βήματα ┃ Προγραμματισμού: Πρώτα βήματα ┃ Αγγλικών: Πολύ καλό
2 Ubuntu 14.04 trusty 3.13.0-32-generic 64bit
3 AMD Athlon II Dual-Core M320‖RAM 3950 MiB‖Hewlett-Packard 3636 - HP Pavilion dv6
4 Advanced Micro Devices, Inc. [AMD/ATI] RV710/M92 [Mobility Radeon HD 4530/4570/545v] [1002:9553] {radeon}
5 wlan0: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01) eth0: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 03)
eval
babeTUX
babeTUX
 
Δημοσιεύσεις: 16
Εγγραφή: 11 Ιούλ 2014, 19:18
Εκτύπωση


  • ΣΧΕΤΙΚΑ ΘΕΜΑΤΑ
    ΑΠΑΝΤΗΣΕΙΣ
    ΠΡΟΒΟΛΕΣ
    ΣΥΓΓΡΑΦΕΑΣ

Επιστροφή στο Κάρτες Δικτύου (Ethernet, WiFi, Bluetooth) / Internet