2 προβλήματα (μου φαίνονται λίγο ασταθή τα 10.04)

[KeRber0s]

Πρώτο πρόβλημα...
Ενώ όλα λειτουργούν καλά ορισμένες φορές δεν μου αναγνωρίζει την κάρτα ethernet. Κάνω boot με windows όλα μια χαρά, boot με linux καμία αντίδραση. Μέτα από κάποια ώρα χρήσης του, πέρασα σε linux και όλα δούλεψαν ρολόι. Τι μπορεί να φταίει..?

Δεύτερο πρόβλημα...
Στον πίνακα εφαρμογών μου αλλάζει τα εικονίδια των μικροεφαρμογών μου τα μετατοπίζει...

Ευχαριστώ εκ των προτέρων...

[xaris2335]

για δώσε τα αποτελέσματα

Κώδικας: Επιλογή όλων

lspci -vv -nn
lsmod
dmesg

Off topic:
Και ενημέρωσε τη υπογραφή σου λέει τα 8.04 ενώ εσύ έχεις τα 10.04

[Epirotes]

Περίεργα μου φαίνονται όλα αυτά! Δεν νομίζω ξαφνικά να χάνει την αναγνώριση της θύρας ethernet και μόντεμ/ρούτερ στα καλά καθούμενα. Τόσα χρόνια πια (2-3) δεν είχα ποτέ πρόβλημα με την σύνδεση στο Linux/GNU/(K)Ubuntu. Είσαι σίγουρος ότι δεν είναι πρόβλημα του παροχέα σου; ή ότι απλά αποσυντονίζεται το μόντεμ/ρούτερ σου;

[KeRber0s]

Οκ με την υπογραφή. Την είχα ξεχασμένη. Όταν βρω χρόνο θα την ολοκληρώσω...

Για να δώσω περισσότερες πληροφορίες:
-Συνδέω το βίσμα στην θύρα και δεν βλέπω καμία απόκριση...
-Πατά αριστερο κλικ στο εικονίδιο για τις Συνδέσεις δυκτίου..
-Συνήθως δύο κατηγορίες: Ενσύρματες Συνδέσεις και Ασύρματες Συνδέσεις. Τώρα μόνο τις ασύρματες.
-Το λαμπάκι στο βίσμα αναβόσβηνε. Ένας άλλος υπολογιστής ήταν κανονικά συνδεδεμένος εκείνη την στιγμή.
-Δώσε πάρε επανεκινήσεις συνδέθηκε.

[KeRber0s]

lspci -vv -nn

Κώδικας: Επιλογή όλων

00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GME Express Memory Controller Hub [8086:27ac] (rev 03)
Subsystem: Hewlett-Packard Company Device [103c:3056]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort+ <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp

00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GME Express Integrated Graphics Controller [8086:27ae] (rev 03)
Subsystem: Hewlett-Packard Company Device [103c:3056]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e8100000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 6000 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at e8180000 (32-bit, non-prefetchable) [size=256K]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915

00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
Subsystem: Hewlett-Packard Company Device [103c:3056]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at e8200000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>

00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:3056]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at e8280000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: e8000000-e80fffff
Prefetchable memory behind bridge: 0000000040000000-00000000401fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:1c.2 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 3 [8086:27d4] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=18, subordinate=18, sec-latency=0
I/O behind bridge: 00004000-00005fff
Memory behind bridge: e4000000-e7ffffff
Prefetchable memory behind bridge: 0000000040200000-00000000403fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:1c.3 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 4 [8086:27d6] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: e0000000-e3ffffff
Prefetchable memory behind bridge: 0000000040400000-00000000405fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:1d.0 USB Controller [0c03]: Intel Corporation N10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:3056]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 6020 [size=32]
Kernel driver in use: uhci_hcd

00:1d.1 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:3056]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 6040 [size=32]
Kernel driver in use: uhci_hcd

00:1d.2 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:3056]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 6060 [size=32]
Kernel driver in use: uhci_hcd

00:1d.3 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:3056]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at 6080 [size=32]
Kernel driver in use: uhci_hcd

00:1d.7 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20)
Subsystem: Hewlett-Packard Company Device [103c:3056]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at e8284000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e1) (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>

00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:3056]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt, intel-rng

00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Device [103c:3056]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 60a0 [size=16]
Kernel driver in use: ata_piix

00:1f.2 SATA controller [0106]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller [8086:27c5] (rev 01) (prog-if 01)
Subsystem: Hewlett-Packard Company Device [103c:3056]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 27
Region 0: I/O ports at 13f0 [size=8]
Region 1: I/O ports at 15f4 [size=4]
Region 2: I/O ports at 1370 [size=8]
Region 3: I/O ports at 1574 [size=4]
Region 4: I/O ports at 60d0 [size=16]
Region 5: Memory at e8285000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci

08:00.0 Network controller [0280]: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:1380]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e8000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: wl
Kernel modules: wl, ssb


lsmod

Κώδικας: Επιλογή όλων

Module Size Used by
binfmt_misc 6587 1
rfcomm 33421 4
ppdev 5259 0
sco 7885 2
bridge 45582 0
stp 1655 1 bridge
bnep 9436 2
l2cap 30624 16 rfcomm,bnep
snd_hda_codec_analog 58566 1
fbcon 35102 71
tileblit 2031 1 fbcon
font 7557 1 fbcon
bitblit 4707 1 fbcon
softcursor 1189 1 bitblit
vga16fb 11385 0
vgastate 8961 1 vga16fb
snd_hda_intel 21877 2
snd_hda_codec 74201 2 snd_hda_codec_analog,snd_hda_intel
snd_hwdep 5412 1 snd_hda_codec
snd_pcm_oss 35308 0
snd_mixer_oss 13746 1 snd_pcm_oss
snd_pcm 70662 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_dummy 1338 0
snd_seq_oss 26726 0
snd_seq_midi 4557 0
snd_rawmidi 19056 1 snd_seq_midi
snd_seq_midi_event 6003 2 snd_seq_oss,snd_seq_midi
snd_seq 47263 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 19098 2 snd_pcm,snd_seq
snd_seq_device 5700 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
joydev 8708 0
snd 54148 16 snd_hda_codec_analog,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
uvcvideo 56990 0
i915 282354 4
videodev 34361 1 uvcvideo
drm_kms_helper 29297 1 i915
intel_agp 24177 2 i915
lib80211_crypt_tkip 7596 0
hp_accel 11144 0
soundcore 6620 1 snd
psmouse 63245 0
v4l1_compat 13251 2 uvcvideo,videodev
serio_raw 3978 0
btusb 10925 2
bluetooth 49892 9 rfcomm,sco,bnep,l2cap,btusb
drm 162471 5 i915,drm_kms_helper
i2c_algo_bit 5028 1 i915
video 17375 1 i915
wl 1959598 0
lis3lv02d 6007 1 hp_accel
input_polldev 2482 1 lis3lv02d
led_class 2864 1 hp_accel
snd_page_alloc 7076 2 snd_hda_intel,snd_pcm
lib80211 5046 2 lib80211_crypt_tkip,wl
output 1871 1 video
agpgart 31724 2 intel_agp,drm
lp 7028 0
parport 32635 2 ppdev,lp
ahci 32008 4


dmesg

Κώδικας: Επιλογή όλων

[ 0.529447] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:20
[ 0.529456] pci 0000:00:1c.3: IO window: 0x2000-0x2fff
[ 0.529469] pci 0000:00:1c.3: MEM window: 0xe0000000-0xe3ffffff
[ 0.529481] pci 0000:00:1c.3: PREFETCH window: 0x00000040400000-0x000000405fffff
[ 0.529496] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
[ 0.529503] pci 0000:00:1e.0: IO window: disabled
[ 0.529514] pci 0000:00:1e.0: MEM window: disabled
[ 0.529523] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.529565] alloc irq_desc for 16 on node -1
[ 0.529573] alloc kstat_irqs on node -1
[ 0.529594] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.529609] pci 0000:00:1c.0: setting latency timer to 64
[ 0.529632] alloc irq_desc for 18 on node -1
[ 0.529638] alloc kstat_irqs on node -1
[ 0.529651] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.529663] pci 0000:00:1c.2: setting latency timer to 64
[ 0.529682] alloc irq_desc for 19 on node -1
[ 0.529688] alloc kstat_irqs on node -1
[ 0.529699] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.529711] pci 0000:00:1c.3: setting latency timer to 64
[ 0.529727] pci 0000:00:1e.0: setting latency timer to 64
[ 0.529739] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.529748] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.529757] pci_bus 0000:08: resource 0 io: [0x3000-0x3fff]
[ 0.529766] pci_bus 0000:08: resource 1 mem: [0xe8000000-0xe80fffff]
[ 0.529775] pci_bus 0000:08: resource 2 pref mem [0x40000000-0x401fffff]
[ 0.529784] pci_bus 0000:18: resource 0 io: [0x4000-0x5fff]
[ 0.529792] pci_bus 0000:18: resource 1 mem: [0xe4000000-0xe7ffffff]
[ 0.529801] pci_bus 0000:18: resource 2 pref mem [0x40200000-0x403fffff]
[ 0.529810] pci_bus 0000:20: resource 0 io: [0x2000-0x2fff]
[ 0.529818] pci_bus 0000:20: resource 1 mem: [0xe0000000-0xe3ffffff]
[ 0.529827] pci_bus 0000:20: resource 2 pref mem [0x40400000-0x405fffff]
[ 0.529836] pci_bus 0000:02: resource 3 io: [0x00-0xffff]
[ 0.529844] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
[ 0.529941] NET: Registered protocol family 2
[ 0.530225] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.531218] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.532412] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.532973] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.532983] TCP reno registered
[ 0.533257] NET: Registered protocol family 1
[ 0.533318] pci 0000:00:02.0: Boot video device
[ 0.534076] cpufreq-nforce2: No nForce2 chipset.
[ 0.534166] Scanning for low memory corruption every 60 seconds
[ 0.534549] audit: initializing netlink socket (disabled)
[ 0.534576] type=2000 audit(1276073278.530:1): initialized
[ 0.556149] highmem bounce pool size: 64 pages
[ 0.556167] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.561491] VFS: Disk quotas dquot_6.5.2
[ 0.561688] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.563719] fuse init (API version 7.13)
[ 0.564039] msgmni has been set to 1716
[ 0.564733] alg: No test for stdrng (krng)
[ 0.564930] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.564939] io scheduler noop registered
[ 0.564945] io scheduler anticipatory registered
[ 0.564952] io scheduler deadline registered
[ 0.565099] io scheduler cfq registered (default)
[ 0.565439] alloc irq_desc for 24 on node -1
[ 0.565448] alloc kstat_irqs on node -1
[ 0.565475] pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
[ 0.565497] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.565779] alloc irq_desc for 25 on node -1
[ 0.565786] alloc kstat_irqs on node -1
[ 0.565804] pcieport 0000:00:1c.2: irq 25 for MSI/MSI-X
[ 0.565822] pcieport 0000:00:1c.2: setting latency timer to 64
[ 0.566099] alloc irq_desc for 26 on node -1
[ 0.566107] alloc kstat_irqs on node -1
[ 0.566127] pcieport 0000:00:1c.3: irq 26 for MSI/MSI-X
[ 0.566146] pcieport 0000:00:1c.3: setting latency timer to 64
[ 0.566404] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.566671] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.577982] ACPI: AC Adapter [C1BE] (off-line)
[ 0.578323] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
[ 0.578336] ACPI: Sleep Button [C1F5]
[ 0.578483] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[ 0.578656] ACPI: Lid Switch [C1C4]
[ 0.578811] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 0.578820] ACPI: Power Button [PWRF]
[ 0.579448] fan PNP0C0B:00: registered as cooling_device0
[ 0.579468] ACPI: Fan [C2DF] (off)
[ 0.579932] fan PNP0C0B:01: registered as cooling_device1
[ 0.579956] ACPI: Fan [C2E0] (off)
[ 0.580440] fan PNP0C0B:02: registered as cooling_device2
[ 0.580459] ACPI: Fan [C2E1] (off)
[ 0.580929] fan PNP0C0B:03: registered as cooling_device3
[ 0.580948] ACPI: Fan [C2E2] (off)
[ 0.581413] fan PNP0C0B:04: registered as cooling_device4
[ 0.581432] ACPI: Fan [C2E3] (off)
[ 0.583305] ACPI: SSDT 3f7f5192 0024A (v01 HP Cpu0Ist 00003000 INTL 20050624)
[ 0.584718] ACPI: SSDT 3f7f5461 00663 (v01 HP Cpu0Cst 00003001 INTL 20050624)
[ 0.591719] Monitor-Mwait will be used to enter C-1 state
[ 0.591842] Monitor-Mwait will be used to enter C-2 state
[ 0.591954] Monitor-Mwait will be used to enter C-3 state
[ 0.591979] Marking TSC unstable due to TSC halts in idle
[ 0.592161] processor LNXCPU:00: registered as cooling_device5
[ 0.593177] ACPI: SSDT 3f7f50be 000D4 (v01 HP Cpu1Ist 00003000 INTL 20050624)
[ 0.594180] ACPI: SSDT 3f7f53dc 00085 (v01 HP Cpu1Cst 00003000 INTL 20050624)
[ 0.595769] Switching to clocksource hpet
[ 0.605521] processor LNXCPU:01: registered as cooling_device6
[ 0.667477] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.667510] ACPI: Thermal Zone [TZ0] (30 C)
[ 0.679173] thermal LNXTHERM:02: registered as thermal_zone1
[ 0.679207] ACPI: Thermal Zone [TZ1] (30 C)
[ 0.681657] Freeing initrd memory: 7784k freed
[ 0.697891] thermal LNXTHERM:03: registered as thermal_zone2
[ 0.697915] ACPI: Thermal Zone [TZ2] (22 C)
[ 0.712281] thermal LNXTHERM:04: registered as thermal_zone3
[ 0.712308] ACPI: Thermal Zone [TZ3] (21 C)
[ 0.719237] thermal LNXTHERM:05: registered as thermal_zone4
[ 0.719256] ACPI: Thermal Zone [TZ4] (49 C)
[ 0.720722] isapnp: Scanning for PnP cards...
[ 0.724509] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.728462] brd: module loaded
[ 0.729982] loop: module loaded
[ 0.730232] input: Macintosh mouse button emulation as /devices/virtual/input/input3
[ 0.730483] ata_piix 0000:00:1f.1: version 2.13
[ 0.730513] ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.730594] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 0.730773] scsi0 : ata_piix
[ 0.731009] scsi1 : ata_piix
[ 0.732193] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x60a0 irq 14
[ 0.732202] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x60a8 irq 15
[ 0.733247] Fixed MDIO Bus: probed
[ 0.733355] PPP generic driver version 2.4.2
[ 0.733496] tun: Universal TUN/TAP device driver, 1.6
[ 0.733503] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.733743] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.733792] alloc irq_desc for 20 on node -1
[ 0.733798] alloc kstat_irqs on node -1
[ 0.733815] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.733848] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.733857] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.733960] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 0.734006] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 0.734027] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.737910] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 0.737959] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xe8284000
[ 0.742248] ata2: port disabled. ignoring.
[ 0.752040] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.752325] usb usb1: configuration #1 chosen from 1 choice
[ 0.752416] hub 1-0:1.0: USB hub found
[ 0.752440] hub 1-0:1.0: 8 ports detected
[ 0.752636] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.752681] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.752761] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.752778] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.752787] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.752885] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.752932] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00006020
[ 0.753219] usb usb2: configuration #1 chosen from 1 choice
[ 0.753300] hub 2-0:1.0: USB hub found
[ 0.753319] hub 2-0:1.0: 2 ports detected
[ 0.753435] alloc irq_desc for 21 on node -1
[ 0.753442] alloc kstat_irqs on node -1
[ 0.753457] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.753472] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.753480] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.753581] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 0.753641] uhci_hcd 0000:00:1d.1: irq 21, io base 0x00006040
[ 0.753897] usb usb3: configuration #1 chosen from 1 choice
[ 0.753976] hub 3-0:1.0: USB hub found
[ 0.753995] hub 3-0:1.0: 2 ports detected
[ 0.754110] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.754125] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.754133] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.754225] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 0.754281] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00006060
[ 0.754543] usb usb4: configuration #1 chosen from 1 choice
[ 0.754624] hub 4-0:1.0: USB hub found
[ 0.754643] hub 4-0:1.0: 2 ports detected
[ 0.754758] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.754773] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 0.754781] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 0.754878] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 0.754934] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00006080
[ 0.755178] usb usb5: configuration #1 chosen from 1 choice
[ 0.755258] hub 5-0:1.0: USB hub found
[ 0.755282] hub 5-0:1.0: 2 ports detected
[ 0.755541] PNP: PS/2 Controller [PNP0303:C1CF,PNP0f12:C1D0] at 0x60,0x64 irq 1,12
[ 0.757225] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 0.757957] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.757978] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.758081] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.758156] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.758229] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.758631] mice: PS/2 mouse device common for all mice
[ 0.759025] rtc_cmos 00:05: RTC can wake from S4
[ 0.759133] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 0.759975] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.760355] device-mapper: uevent: version 1.0.3
[ 0.760738] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.760966] device-mapper: multipath: version 1.1.0 loaded
[ 0.760976] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.761318] EISA: Probing bus 0 at eisa.0
[ 0.761332] Cannot allocate resource for EISA slot 1
[ 0.761339] Cannot allocate resource for EISA slot 2
[ 0.761345] Cannot allocate resource for EISA slot 3
[ 0.761351] Cannot allocate resource for EISA slot 4
[ 0.761358] Cannot allocate resource for EISA slot 5
[ 0.761364] Cannot allocate resource for EISA slot 6
[ 0.761382] EISA: Detected 0 cards.
[ 0.761840] cpuidle: using governor ladder
[ 0.762171] cpuidle: using governor menu
[ 0.763433] TCP cubic registered
[ 0.763916] NET: Registered protocol family 10
[ 0.765330] lo: Disabled Privacy Extensions
[ 0.766272] NET: Registered protocol family 17
[ 0.767716] Using IPI No-Shortcut mode
[ 0.768088] PM: Resume from disk failed.
[ 0.768128] registered taskstats version 1
[ 0.768740] Magic number: 14:756:775
[ 0.768751] misc psaux: hash matches
[ 0.768802] misc fuse: hash matches
[ 0.768914] rtc_cmos 00:05: setting system clock to 2010-06-09 08:47:59 UTC (1276073279)
[ 0.768925] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.768930] EDD information not available.
[ 0.790794] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 0.805708] ACPI: Battery Slot [C1C0] (battery present)
[ 1.064049] usb 1-4: new high speed USB device using ehci_hcd and address 2
[ 1.074822] isapnp: No Plug & Play device found
[ 1.074903] Freeing unused kernel memory: 656k freed
[ 1.075480] Write protecting the kernel text: 4676k
[ 1.075554] Write protecting the kernel read-only data: 1840k
[ 1.114177] udev: starting version 151
[ 1.235528] usb 1-4: configuration #1 chosen from 1 choice
[ 1.467268] ahci 0000:00:1f.2: version 3.0
[ 1.467312] alloc irq_desc for 17 on node -1
[ 1.467320] alloc kstat_irqs on node -1
[ 1.467338] ahci 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.467416] alloc irq_desc for 27 on node -1
[ 1.467423] alloc kstat_irqs on node -1
[ 1.467444] ahci 0000:00:1f.2: irq 27 for MSI/MSI-X
[ 1.467529] ahci: SSS flag set, parallel bus scan disabled
[ 1.467584] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x1 impl SATA mode
[ 1.467596] ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part
[ 1.467610] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.467957] scsi2 : ahci
[ 1.484767] scsi3 : ahci
[ 1.485544] scsi4 : ahci
[ 1.485820] scsi5 : ahci
[ 1.486147] ata3: SATA max UDMA/133 abar m1024@0xe8285000 port 0xe8285100 irq 27
[ 1.486157] ata4: DUMMY
[ 1.486163] ata5: DUMMY
[ 1.486168] ata6: DUMMY
[ 1.632123] usb 4-1: new full speed USB device using uhci_hcd and address 2
[ 1.803783] usb 4-1: configuration #1 chosen from 1 choice
[ 1.968192] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.972382] ata3.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 1.972394] ata3.00: ACPI cmd b1/c1:00:00:00:00:a0 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 1.972563] ata3.00: ACPI cmd c6/00:10:00:00:00:a0 (SET MULTIPLE MODE) succeeded
[ 1.972582] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.973234] ata3.00: ATA-8: FUJITSU MHZ2160BH G2, 8909, max UDMA/100
[ 1.973250] ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.977716] ata3.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 1.977727] ata3.00: ACPI cmd b1/c1:00:00:00:00:a0 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 1.977895] ata3.00: ACPI cmd c6/00:10:00:00:00:a0 (SET MULTIPLE MODE) succeeded
[ 1.977914] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.978632] ata3.00: configured for UDMA/100
[ 1.993778] ata3.00: configured for UDMA/100
[ 1.993792] ata3: EH complete
[ 1.994098] scsi 2:0:0:0: Direct-Access ATA FUJITSU MHZ2160B 8909 PQ: 0 ANSI: 5
[ 1.994580] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 1.994626] sd 2:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 1.994827] sd 2:0:0:0: [sda] Write Protect is off
[ 1.994838] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.994936] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.995453] sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
[ 2.071593] sd 2:0:0:0: [sda] Attached SCSI disk
[ 3.344677] EXT4-fs (sda5): mounted filesystem with ordered data mode
[ 13.777851] Adding 2000020k swap on /dev/sda6. Priority:-1 extents:1 across:2000020k
[ 13.847294] udev: starting version 151
[ 13.923473] lp: driver loaded but no devices found
[ 14.263331] lib80211: common routines for IEEE802.11 drivers
[ 14.263340] lib80211_crypt: registered algorithm 'NULL'
[ 14.284949] Linux agpgart interface v0.103
[ 14.366832] intel_rng: FWH not detected
[ 14.436227] wl: module license 'MIXED/Proprietary' taints kernel.
[ 14.436237] Disabling lock debugging due to kernel taint
[ 14.722901] wl 0000:08:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 14.722923] wl 0000:08:00.0: setting latency timer to 64
[ 14.816981] acpi device:01: registered as cooling_device7
[ 14.821703] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input5
[ 14.821867] ACPI: Video Device [C083] (multi-head: yes rom: no post: no)
[ 14.897219] [drm] Initialized drm 1.1.0 20060810
[ 14.898717] Bluetooth: Core ver 2.15
[ 14.899044] NET: Registered protocol family 31
[ 14.899052] Bluetooth: HCI device and connection manager initialized
[ 14.899061] Bluetooth: HCI socket layer initialized
[ 14.908395] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 14.909566] usbcore: registered new interface driver btusb
[ 14.938128] lis3lv02d: hardware type HP2140 found.
[ 14.944747] lis3lv02d: 1-byte sensor found
[ 14.944992] lib80211_crypt: registered algorithm 'TKIP'
[ 14.987757] agpgart-intel 0000:00:00.0: Intel 945GME Chipset
[ 14.988101] agpgart-intel 0000:00:00.0: detected 7932K stolen memory
[ 14.990939] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[ 15.005690] EXT4-fs (sda7): mounted filesystem with ordered data mode
[ 15.043532] eth0: Broadcom BCM432b 802.11 Hybrid Wireless Controller 5.60.48.36
[ 15.049204] Linux video capture interface: v2.00
[ 15.092512] type=1505 audit(1276062493.823:2): operation="profile_load" pid=658 name="/sbin/dhclient3"
[ 15.093350] type=1505 audit(1276062493.823:3): operation="profile_load" pid=658 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 15.093811] type=1505 audit(1276062493.823:4): operation="profile_load" pid=658 name="/usr/lib/connman/scripts/dhclient-script"
[ 15.096878] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input6
[ 15.099615] Registered led device: hp::hddprotect
[ 15.099767] lis3lv02d driver loaded.
[ 15.197759] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 15.197776] i915 0000:00:02.0: setting latency timer to 64
[ 15.217670] kjournald starting. Commit interval 5 seconds
[ 15.218169] EXT3 FS on sda8, internal journal
[ 15.218185] EXT3-fs: mounted filesystem with ordered data mode.
[ 15.247837] [drm] set up 7M of stolen space
[ 15.274235] uvcvideo: Found UVC 1.00 device CNF8031 (04f2:b12e)
[ 15.295421] input: CNF8031 as /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4:1.0/input/input7
[ 15.295581] usbcore: registered new interface driver uvcvideo
[ 15.295590] USB Video Class driver (v0.1.0)
[ 15.354642] udev: renamed network interface eth0 to eth1
[ 15.357188] [drm] initialized overlay support
[ 15.662276] Synaptics Touchpad, model: 1, fw: 6.5, id: 0x1c0b1, caps: 0xa04711/0xa00000
[ 15.781757] fb0: inteldrmfb frame buffer device
[ 15.781764] registered panic notifier
[ 15.781781] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 15.784160] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8
[ 15.793390] vga16fb: initializing
[ 15.793402] vga16fb: mapped to 0xc00a0000
[ 15.793413] vga16fb: not registering due to another framebuffer present
[ 15.797325] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
[ 15.797354] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 15.797438] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 16.092507] Console: switching to colour frame buffer device 128x36
[ 16.228254] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
[ 21.133472] type=1505 audit(1276062499.863:5): operation="profile_load" pid=842 name="/usr/share/gdm/guest-session/Xsession"
[ 21.148344] type=1505 audit(1276062499.879:6): operation="profile_replace" pid=843 name="/sbin/dhclient3"
[ 21.149164] type=1505 audit(1276062499.879:7): operation="profile_replace" pid=843 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 21.149635] type=1505 audit(1276062499.879:8): operation="profile_replace" pid=843 name="/usr/lib/connman/scripts/dhclient-script"
[ 21.173437] type=1505 audit(1276062499.903:9): operation="profile_load" pid=845 name="/usr/bin/evince"
[ 21.194280] type=1505 audit(1276062499.923:10): operation="profile_load" pid=845 name="/usr/bin/evince-previewer"
[ 21.235136] type=1505 audit(1276062499.963:11): operation="profile_load" pid=845 name="/usr/bin/evince-thumbnailer"
[ 21.296859] type=1505 audit(1276062500.027:12): operation="profile_load" pid=915 name="/usr/lib/cups/backend/cups-pdf"
[ 21.297900] type=1505 audit(1276062500.027:13): operation="profile_load" pid=915 name="/usr/sbin/cupsd"
[ 21.316692] type=1505 audit(1276062500.047:14): operation="profile_load" pid=916 name="/usr/sbin/tcpdump"
[ 21.759354] Bluetooth: L2CAP ver 2.14
[ 21.759363] Bluetooth: L2CAP socket layer initialized
[ 21.785883] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 21.785893] Bluetooth: BNEP filters: protocol multicast
[ 21.824215] Bridge firewalling registered
[ 21.913942] Bluetooth: SCO (Voice Link) ver 0.6
[ 21.913951] Bluetooth: SCO socket layer initialized
[ 21.956820] ppdev: user-space parallel port driver
[ 22.060981] Bluetooth: RFCOMM TTY layer initialized
[ 22.060992] Bluetooth: RFCOMM socket layer initialized
[ 22.060997] Bluetooth: RFCOMM ver 1.11
[ 22.572977] CPU0 attaching NULL sched-domain.
[ 22.572994] CPU1 attaching NULL sched-domain.
[ 22.604289] CPU0 attaching sched-domain:
[ 22.604305] domain 0: span 0-1 level SIBLING
[ 22.604319] groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[ 22.604345] domain 1: span 0-1 level MC
[ 22.604356] groups: 0-1 (cpu_power = 1178)
[ 22.604378] CPU1 attaching sched-domain:
[ 22.604388] domain 0: span 0-1 level SIBLING
[ 22.604398] groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[ 22.604422] domain 1: span 0-1 level MC
[ 22.604432] groups: 0-1 (cpu_power = 1178)
[ 27.586126] CPU0 attaching NULL sched-domain.
[ 27.586141] CPU1 attaching NULL sched-domain.
[ 27.608189] CPU0 attaching sched-domain:
[ 27.608200] domain 0: span 0-1 level SIBLING
[ 27.608209] groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[ 27.608227] domain 1: span 0-1 level MC
[ 27.608235] groups: 0-1 (cpu_power = 1178)
[ 27.608251] CPU1 attaching sched-domain:
[ 27.608258] domain 0: span 0-1 level SIBLING
[ 27.608266] groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[ 27.608283] domain 1: span 0-1 level MC
[ 27.608290] groups: 0-1 (cpu_power = 1178)
[ 32.065042] eth1: no IPv6 routers present
[ 49.750248] process `skype' is using obsolete setsockopt SO_BSDCOMPAT
[ 360.373973] possible SYN flooding on port 62381. Sending cookies.
[ 421.938189] possible SYN flooding on port 62381. Sending cookies.
[ 480.676444] CPU0 attaching NULL sched-domain.
[ 480.676458] CPU1 attaching NULL sched-domain.
[ 480.704186] CPU0 attaching sched-domain:
[ 480.704196] domain 0: span 0-1 level SIBLING
[ 480.704204] groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[ 480.704221] domain 1: span 0-1 level MC
[ 480.704229] groups: 0-1 (cpu_power = 1178)
[ 480.704247] CPU1 attaching sched-domain:
[ 480.704253] domain 0: span 0-1 level SIBLING
[ 480.704259] groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[ 480.704274] domain 1: span 0-1 level MC
[ 480.704281] groups: 0-1 (cpu_power = 1178)
[ 480.711173] ata3.00: exception Emask 0x10 SAct 0x1 SErr 0x50000 action 0xe frozen
[ 480.711186] ata3.00: irq_stat 0x00400000, PHY RDY changed
[ 480.711198] ata3: SError: { PHYRdyChg CommWake }
[ 480.711208] ata3.00: failed command: WRITE FPDMA QUEUED
[ 480.711228] ata3.00: cmd 61/08:00:65:87:6d/00:00:04:00:00/40 tag 0 ncq 4096 out
[ 480.711232] res 50/00:fe:00:00:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error)
[ 480.711241] ata3.00: status: { DRDY }
[ 480.711258] ata3: hard resetting link
[ 481.600107] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 481.609896] ata3.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 481.609912] ata3.00: ACPI cmd b1/c1:00:00:00:00:a0 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 481.610063] ata3.00: ACPI cmd c6/00:10:00:00:00:a0 (SET MULTIPLE MODE) succeeded
[ 481.610077] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 481.616093] ata3.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 481.616105] ata3.00: ACPI cmd b1/c1:00:00:00:00:a0 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 481.616265] ata3.00: ACPI cmd c6/00:10:00:00:00:a0 (SET MULTIPLE MODE) succeeded
[ 481.616284] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 481.616907] ata3.00: configured for UDMA/100
[ 481.618383] ata3.00: configured for UDMA/100
[ 481.618417] ata3: EH complete
[ 486.308645] possible SYN flooding on port 62381. Sending cookies.
[ 520.332076] CE: hpet increasing min_delta_ns to 15000 nsec
[ 546.515647] possible SYN flooding on port 62381. Sending cookies.
[ 575.865695] operapluginwrap[2209]: segfault at 0 ip (null) sp bfc8b7ec error 4 in libXt.so.6.0.0[110000+4f000]
[ 575.941940] operapluginwrap[2211]: segfault at 0 ip (null) sp bfd0755c error 4 in libXext.so.6.4.0[110000+e000]
[ 576.254921] operapluginwrap[2215]: segfault at 0 ip (null) sp bfb1e85c error 4 in libgcc_s.so.1[110000+1d000]
[ 576.318844] operapluginwrap[2216]: segfault at 0 ip (null) sp bff2f3cc error 4 in libXext.so.6.4.0[110000+e000]
[ 582.951813] UDP: bad checksum. From 121.96.168.188:45682 to 192.168.1.64:62381 ulen 38
[ 855.617936] UDP: bad checksum. From 121.96.168.188:45682 to 192.168.1.64:62381 ulen 38
[11842.081121] possible SYN flooding on port 59334. Sending cookies.
[11919.913274] possible SYN flooding on port 59334. Sending cookies.
[12129.715829] possible SYN flooding on port 59334. Sending cookies.
[12330.680174] possible SYN flooding on port 59334. Sending cookies.
[12392.436405] possible SYN flooding on port 59334. Sending cookies.
[12476.211181] possible SYN flooding on port 59334. Sending cookies.
[12562.825987] possible SYN flooding on port 59334. Sending cookies.
[12632.197713] possible SYN flooding on port 59334. Sending cookies.
[12692.322141] possible SYN flooding on port 59334. Sending cookies.
[12764.833216] possible SYN flooding on port 59334. Sending cookies.
[12907.502168] possible SYN flooding on port 59334. Sending cookies.
[12994.185145] possible SYN flooding on port 59334. Sending cookies.
[13077.206274] possible SYN flooding on port 59334. Sending cookies.
[13206.920513] possible SYN flooding on port 59334. Sending cookies.
[13268.805784] possible SYN flooding on port 59334. Sending cookies.
[13364.617426] possible SYN flooding on port 59334. Sending cookies.
[13599.547132] possible SYN flooding on port 59334. Sending cookies.


[xaris2335]

Για δώσε

Κώδικας: Επιλογή όλων

sudo modprobe r8169

και κάνε επανεκκίνηση.

[KeRber0s]

Θα το κάνω... Αλλά δεν μπορώ να σας πώ άμεσα το αποτέλεσμα.. Μια και η σύνδεση ήταν φίλου μου... Οπότε μόλις τον ξαναβρώ θα σας πώ αν είχε αποτέλεσμα..
Off topic:
Όμως για να μαθαίνου οι καινούριοι και να θυμούνται οι παλιοί μπορείς να μας πεις και τι θα κάνει η εντολή...?

[KeRber0s]

Το έκανα και είχα το εξής αποτέλεσμα...
Σύνδεσα το καλώδιο.. Δεν λειτούργούσε μάλιστα έχει δύο λαμπάκια πράσινο (ανάβει μόλις συνδέσεις το καλώδιο) και πορτοκαλί (μόλις ανταλάσει δεδομένα ή συνδεθεί σε δύκτιο)
Σε linux άναβε το πράσινο λαμπάκι...
Στα windows δεν άναβε τίποτα...

Στην συνέχεια...
Εκκίνηση με το καλώδιο συνδεδεμόνο...
Σε linux συνδέθηκε...
Σε windows ακόμα περιμένω...

[Epirotes]

Off topic:
Από το man modprobe μαθαίνεις ότι: το modprobe προσθέτει ή αφαιρεί με έξυπνο τρόπο ένα module στον/από τον πυρήνα Linux. Τώρα ήρθε στα ίσια του το μηχάνημα -δεν θυμάμαι αν το είπα και πιο πάνω αλλά 3 χρόνια σχεδόν στο ubuntu δεν έχω δει ποτέ μα ποτέ πρόβλημα σύνδεσης -μόνο όταν έχει βλάβη ο ΟΤΕ σκαλώνει κι αυτό δόξα τον Αλλάχ δεν συμβαίνει και πολύ συχνά πλέον. Πέρα από την πλάκα κάτι περίεργο συμβαίνει με το μόντεμ/ρούτερ σου (του φίλου σου έστω) ή με την θύρα ethernet.

[KeRber0s]

Εγώ σκέφτηκα κάτι αλλά δεν είμαι και τόσο σίγουρος...
Απλά κατά την εκκίνηση να μην λειτουργεί η θύρα μου με αποτέλεσμα να μην την αναγνωρίζει το σύστημα...
Όταν το συνδέω από την αρχή το καλώδιο να την βρίσκει..
Π.χ. τώραν την βρίσκει παρόλο που το καλώδιο δεν είναι πάνω στον υπολογιστή..!

Αλλά ανέφερα και ένα ακόμα πρόβλημα που αντιμετωπίζω...

Δεύτερο πρόβλημα...
Στον πίνακα εφαρμογών μου αλλάζει τα εικονίδια των μικροεφαρμογών μου τα μετατοπίζει...

Αλλά μετά από επανεκίνηση τα επαναφέρει στην αρχική τους κατάσταση... Δεν είναι και τόσο σοβαρό αλλά είναι σπαστικό...