- Κώδικας: Επιλογή όλων
ubuntu@lubuntu:~$ sudo smartctl -a /dev/sda
smartctl 6.4 2014-10-07 r4002 [i686-linux-4.2.0-16-generic] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Fujitsu MHV
Device Model: FUJITSU MHV2040BH
Serial Number: NW19T6127YVF
Firmware Version: 00000028
User Capacity: 40.007.761.920 bytes [40,0 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 T13/1532D revision 4a
Local Time is: Thu Dec 10 20:45:59 2015 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 240) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 28) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 065 046 Pre-fail Always - 31228707345853
2 Throughput_Performance 0x0005 100 100 030 Pre-fail Offline - 12189696
3 Spin_Up_Time 0x0003 100 100 025 Pre-fail Always - 1
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 4326
5 Reallocated_Sector_Ct 0x0033 099 099 024 Pre-fail Always - 92 (1969 31)
7 Seek_Error_Rate 0x000f 100 100 047 Pre-fail Always - 512
8 Seek_Time_Performance 0x0005 100 100 019 Pre-fail Offline - 0
9 Power_On_Seconds 0x0032 089 089 000 Old_age Always - 5548h+07m+23s
10 Spin_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 3959
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 268
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 45135
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 35 (Min/Max 9/54)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 873
196 Reallocated_Event_Count 0x0032 099 099 000 Old_age Always - 92 (4 6875)
197 Current_Pending_Sector 0x0012 091 091 000 Old_age Always - 10
198 Offline_Uncorrectable 0x0010 083 083 000 Old_age Offline - 35
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000f 100 100 060 Pre-fail Always - 28398
203 Run_Out_Cancel 0x0002 100 100 000 Old_age Always - 1533259547506
240 Head_Flying_Hours 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 13685 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 13685 occurred at disk power-on lifetime: 5548 hours (231 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 08 00 00 00 e0 Error: AMNF 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 01:30:24.865 READ DMA
c8 00 08 f0 52 a8 e4 00 01:30:24.862 READ DMA
c8 00 08 80 52 a8 e4 00 01:30:24.837 READ DMA
ec 00 01 00 00 00 00 00 01:30:24.834 IDENTIFY DEVICE
27 00 00 00 00 00 e0 00 01:30:24.824 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 13684 occurred at disk power-on lifetime: 5548 hours (231 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 08 00 00 00 e0 Error: AMNF 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 01:30:20.557 READ DMA
27 00 00 00 00 00 e0 00 01:30:20.556 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 01:30:20.547 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 01:30:20.540 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 01:30:20.540 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 13683 occurred at disk power-on lifetime: 5548 hours (231 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 08 00 00 00 e0 Error: AMNF 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 01:30:16.289 READ DMA
27 00 00 00 00 00 e0 00 01:30:16.288 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 01:30:16.279 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 01:30:16.273 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 01:30:16.272 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 13682 occurred at disk power-on lifetime: 5548 hours (231 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 08 18 00 00 e0 Error: AMNF 8 sectors at LBA = 0x00000018 = 24
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 18 00 00 e0 00 01:30:11.989 READ DMA
27 00 00 00 00 00 e0 00 01:30:11.988 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 01:30:11.980 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 01:30:11.973 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 01:30:11.972 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 13681 occurred at disk power-on lifetime: 5548 hours (231 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 08 00 00 00 e0 Error: AMNF 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 01:30:07.669 READ DMA
27 00 00 00 00 00 e0 00 01:30:07.668 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 01:30:07.660 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 01:30:07.653 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 01:30:07.652 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
lubuntu@lubuntu:~$
παντως αυτο που μου βγαζει κατα την εγκατασταση μοιαζει κατα πολυ με τις πρωτες φωτογραφιες εδω:http://ubuntuforums.org/showthread.php?t=1920109
