12.04 αργεί να φορτώσει

[dancer_69]

Κώδικας: Επιλογή όλων

Disk /dev/sda: 500.1 GB, 500107862016 bytes
255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x6b3bb6d9

Device Boot Start End Blocks Id System
/dev/sda1 * 2048 307978239 153988096 7 HPFS/NTFS/exFAT
/dev/sda2 307982115 771441299 231729592+ f W95 Ext'd (LBA)
/dev/sda3 771442688 811687935 20122624 83 Linux
/dev/sda4 811687936 854697983 21505024 83 Linux
/dev/sda5 307982178 539703674 115860748+ 7 HPFS/NTFS/exFAT
/dev/sda6 539703738 771441299 115868781 7 HPFS/NTFS/exFAT

Disk /dev/sdc: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xaa6c801f

Device Boot Start End Blocks Id System
/dev/sdc1 142651392 146159615 1754112 82 Linux swap / Solaris
/dev/sdc2 4094 142651391 71323649 5 Extended
/dev/sdc3 146159616 312580095 83210240 7 HPFS/NTFS/exFAT
/dev/sdc5 4096 142651391 71323648 83 Linux

Partition table entries are not in disk order

Disk /dev/sdd: 119.9 GB, 119897805824 bytes
255 heads, 63 sectors/track, 14576 cylinders, total 234175402 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x42d942d9

Device Boot Start End Blocks Id System
/dev/sdd1 * 2048 234174463 117086208 7 HPFS/NTFS/exFAT

Disk /dev/sde: 250.1 GB, 250059350016 bytes
64 heads, 32 sectors/track, 238475 cylinders, total 488397168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x3c03814c

Device Boot Start End Blocks Id System
/dev/sde1 2048 419440639 209719296 7 HPFS/NTFS/exFAT
/dev/sde2 * 419442688 488392703 34475008 7 HPFS/NTFS/exFAT


[the_eye]

Η εγκατάσταση σου είναι στο /dev/sdc ;

Για τρέξε

Κώδικας: Επιλογή όλων

sudo hdparm -tT /dev/sdc

[Learner]

Βάλε όπου Χ ο δίσκος με το Ubuntu (Μόνο το γράμμα βάζεις, όχι αριθμό.)

O δίσκος είναι ο sda όπως έγραψα παραπάνω.

Στον /dev/sda , που έχεις το Ubuntu όπως αναφέρεις , δεν υπάρχει μνήμη swap.. να φταίει αυτό ; δεν είμαι σίγουρος , μιας και μνήμη απ' ότι βλέπω έχεις αρκετή (3112ΜΒ) .

Αν δεν σου κάνει κόπο , επεξεργάσου το fstab για να προσαρτήσει την μνήμη swap από τον /dev/sdc που βλέπω πως έχεις .

[dancer_69]

Όχι στο sda, στον sdc είναι το διαμέρισμα /home.

Κώδικας: Επιλογή όλων

/dev/sdc:
Timing cached reads: 1682 MB in 2.00 seconds = 840.73 MB/sec
Timing buffered disk reads: 182 MB in 3.01 seconds = 60.37 MB/sec


[dancer_69]

Βάλε όπου Χ ο δίσκος με το Ubuntu (Μόνο το γράμμα βάζεις, όχι αριθμό.)

O δίσκος είναι ο sda όπως έγραψα παραπάνω.

Στον /dev/sda , που έχεις το Ubuntu όπως αναφέρεις , δεν υπάρχει μνήμη swap.. να φταίει αυτό ; δεν είμαι σίγουρος , μιας και μνήμη απ' ότι βλέπω έχεις αρκετή (3112ΜΒ) .

Αν δεν σου κάνει κόπο , επεξεργάσου το fstab για να προσαρτήσει την μνήμη swap από τον /dev/sdc που βλέπω πως έχεις .

Είναι ήδη προσαρτημένο το διαμέρισμα αυτό ως swap.

[the_eye]

Κάτι βρήκαμε ! Γιατί τόσο αργός ο δίσκος ! 60.37 MB/sec είναι παλιός ;

Για δες και αυτό
https://forum.ubuntu-gr.org/viewtopic.php?f=9&t=19749

[dancer_69]

Έτρεξα το smartctl στον sdc και δε βρήκε σφάλματα, όμως βρήκε στον sdd, τον οποίο υποψιαζόμουν μιας και μου έχει δημιουργήσει πρόβλημα ξανά πρόσφατα. Βέβαια με διάφορα test που του είχα κάνει, καθώς και σκανάρισμα με το hdd regenerator δεν παρουσίαζε πρόβλημα.
Το smartctl πάντως τώρα δίνει τα παρακάτω:

Κώδικας: Επιλογή όλων

=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar SE Serial ATA
Device Model: WDC WD1200JS-00MHB0
Serial Number: WD-WCANN1099135
Firmware Version: 02.01C03
User Capacity: 119.897.805.824 bytes [119 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun May 27 00:46:18 2012 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 3360) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 42) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 147
3 Spin_Up_Time 0x0003 189 176 021 Pre-fail Always - 3516
4 Start_Stop_Count 0x0032 095 095 000 Old_age Always - 5439
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 026 026 000 Old_age Always - 54255
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 3192
190 Airflow_Temperature_Cel 0x0022 066 048 045 Old_age Always - 34
194 Temperature_Celsius 0x0022 113 095 000 Old_age Always - 34
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 27135
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0

SMART Error Log Version: 1
ATA Error Count: 167 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 167 occurred at disk power-on lifetime: 21528 hours (897 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 85 de 5e e0 Error: UNC at LBA = 0x005ede85 = 6217349

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 00 00 00:09:19.933 READ DMA
c8 00 08 7f de 5e 00 00 00:09:17.993 READ DMA
c8 00 08 77 de 5e 00 00 00:09:17.993 READ DMA
c8 00 08 6f de 5e 00 00 00:09:17.993 READ DMA
c8 00 08 67 de 5e 00 00 00:09:17.993 READ DMA

Error 166 occurred at disk power-on lifetime: 21528 hours (897 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 85 de 5e e0 Error: UNC at LBA = 0x005ede85 = 6217349

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 80 2f de 5e 00 00 00:09:16.037 READ DMA
c8 00 80 af dd 5e 00 00 00:09:16.036 READ DMA
c8 00 80 2f dd 5e 00 00 00:09:16.035 READ DMA
c8 00 80 af dc 5e 00 00 00:09:16.034 READ DMA
c8 00 80 2f dc 5e 00 00 00:09:16.033 READ DMA

Error 165 occurred at disk power-on lifetime: 21519 hours (896 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 df 45 50 e0 Error: UNC at LBA = 0x005045df = 5260767

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 00 00 00:02:22.363 READ DMA
c8 00 08 df 45 50 00 00 00:02:20.483 READ DMA
c8 00 08 47 f7 05 00 00 00:02:20.483 READ DMA
ca 00 08 ff 1e 61 00 00 00:02:20.483 WRITE DMA
c8 00 08 df 45 50 00 00 00:02:18.554 READ DMA

Error 164 occurred at disk power-on lifetime: 21519 hours (896 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 df 45 50 e0 Error: WP at LBA = 0x005045df = 5260767

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 08 ff 1e 61 00 00 00:02:20.483 WRITE DMA
c8 00 08 df 45 50 00 00 00:02:18.554 READ DMA
c8 00 08 3f f7 05 00 00 00:02:18.542 READ DMA
c8 00 01 00 00 00 00 00 00:02:18.530 READ DMA
c8 00 40 e9 59 fe 05 00 00:02:18.514 READ DMA

Error 163 occurred at disk power-on lifetime: 21519 hours (896 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 df 45 50 e0 Error: UNC at LBA = 0x005045df = 5260767

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 b7 20 79 04 00 00:02:18.444 READ DMA
c8 00 08 df 45 50 00 00 00:02:16.445 READ DMA
ca 00 08 3f ac 2e 00 00 00:02:16.445 WRITE DMA
ca 00 08 9f ab 2e 00 00 00:02:16.445 WRITE DMA
c8 00 38 27 16 14 00 00 00:02:16.442 READ DMA

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 53315 -
# 2 Conveyance offline Completed without error 00% 53314 -
# 3 Short offline Completed without error 00% 53300 -
# 4 Short offline Completed without error 00% 49750 -
# 5 Short offline Completed without error 00% 35434 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

zaxus-ubuntu@zaxusubuntu-System-Product:~$ clear

zaxus-ubuntu@zaxusubuntu-System-Product:~$ sudo smartctl -a /dev/sdd
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-24-generic] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar SE Serial ATA
Device Model: WDC WD1200JS-00MHB0
Serial Number: WD-WCANN1099135
Firmware Version: 02.01C03
User Capacity: 119.897.805.824 bytes [119 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun May 27 00:46:29 2012 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 3360) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 42) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 147
3 Spin_Up_Time 0x0003 189 176 021 Pre-fail Always - 3516
4 Start_Stop_Count 0x0032 095 095 000 Old_age Always - 5439
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 026 026 000 Old_age Always - 54255
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 3192
190 Airflow_Temperature_Cel 0x0022 066 048 045 Old_age Always - 34
194 Temperature_Celsius 0x0022 113 095 000 Old_age Always - 34
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 27135
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0

SMART Error Log Version: 1
ATA Error Count: 167 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 167 occurred at disk power-on lifetime: 21528 hours (897 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 85 de 5e e0 Error: UNC at LBA = 0x005ede85 = 6217349

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 00 00 00:09:19.933 READ DMA
c8 00 08 7f de 5e 00 00 00:09:17.993 READ DMA
c8 00 08 77 de 5e 00 00 00:09:17.993 READ DMA
c8 00 08 6f de 5e 00 00 00:09:17.993 READ DMA
c8 00 08 67 de 5e 00 00 00:09:17.993 READ DMA

Error 166 occurred at disk power-on lifetime: 21528 hours (897 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 85 de 5e e0 Error: UNC at LBA = 0x005ede85 = 6217349

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 80 2f de 5e 00 00 00:09:16.037 READ DMA
c8 00 80 af dd 5e 00 00 00:09:16.036 READ DMA
c8 00 80 2f dd 5e 00 00 00:09:16.035 READ DMA
c8 00 80 af dc 5e 00 00 00:09:16.034 READ DMA
c8 00 80 2f dc 5e 00 00 00:09:16.033 READ DMA

Error 165 occurred at disk power-on lifetime: 21519 hours (896 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 df 45 50 e0 Error: UNC at LBA = 0x005045df = 5260767

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 00 00 00:02:22.363 READ DMA
c8 00 08 df 45 50 00 00 00:02:20.483 READ DMA
c8 00 08 47 f7 05 00 00 00:02:20.483 READ DMA
ca 00 08 ff 1e 61 00 00 00:02:20.483 WRITE DMA
c8 00 08 df 45 50 00 00 00:02:18.554 READ DMA

Error 164 occurred at disk power-on lifetime: 21519 hours (896 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 df 45 50 e0 Error: WP at LBA = 0x005045df = 5260767

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 08 ff 1e 61 00 00 00:02:20.483 WRITE DMA
c8 00 08 df 45 50 00 00 00:02:18.554 READ DMA
c8 00 08 3f f7 05 00 00 00:02:18.542 READ DMA
c8 00 01 00 00 00 00 00 00:02:18.530 READ DMA
c8 00 40 e9 59 fe 05 00 00:02:18.514 READ DMA

Error 163 occurred at disk power-on lifetime: 21519 hours (896 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 df 45 50 e0 Error: UNC at LBA = 0x005045df = 5260767

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 b7 20 79 04 00 00:02:18.444 READ DMA
c8 00 08 df 45 50 00 00 00:02:16.445 READ DMA
ca 00 08 3f ac 2e 00 00 00:02:16.445 WRITE DMA
ca 00 08 9f ab 2e 00 00 00:02:16.445 WRITE DMA
c8 00 38 27 16 14 00 00 00:02:16.442 READ DMA

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 53315 -
# 2 Conveyance offline Completed without error 00% 53314 -
# 3 Short offline Completed without error 00% 53300 -
# 4 Short offline Completed without error 00% 49750 -
# 5 Short offline Completed without error 00% 35434 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.


[the_eye]

Ο δίσκος έχει πρόβλημα

Κώδικας: Επιλογή όλων

199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 27135

και από ότι βλέπω έχει γράψει και πολλές ώρες λειτουργίας !!!

Κώδικας: Επιλογή όλων

9 Power_On_Hours 0x0032 026 026 000 Old_age Always - 54255

στην θέση σου δεν θα τον εμπιστευόμουνα πολύ.

Δώσε μας και το sdc

[dancer_69]

Ναι, είναι αρκετά παλιός, και όντως δεν τον εμπιστεύομαι, γι' αυτό και δεν έχω ούτε λειτουργικό πάνω ούτε κάνω συχνές εγγραφές/διαγραφές.

εδώ ο sdc:

Κώδικας: Επιλογή όλων

=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar SE Serial ATA
Device Model: WDC WD1600JS-00NCB1
Serial Number: WD-WCANM6933215
Firmware Version: 10.02E02
User Capacity: 160.041.885.696 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun May 27 01:08:44 2012 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 4980) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 60) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 189 178 021 Pre-fail Always - 3508
4 Start_Stop_Count 0x0032 095 095 000 Old_age Always - 5704
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 053 053 000 Old_age Always - 34793
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 2872
190 Airflow_Temperature_Cel 0x0022 056 030 045 Old_age Always In_the_past 44
194 Temperature_Celsius 0x0022 103 077 000 Old_age Always - 44
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 1500
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.


EDIT:
Άλλαξα στο bios το IDE Channel 0 master από AUTO σε ΝΟΝΕ για τον sdd.
Το αποτέλεσμα:
-λίγο γρηγορότερο boot μέχρι τη φόρτωση το grub
-το ubuntu φορτώνει όπως πριν μέχρι την οθόνη σύνδεσης(ίσως μια βελτίωση 5-10 δευτ.)
-λύθηκε το πρόβλημα της μεγάλης καθυστέρησης στα σχετικά με τους δίσκους όπως blkid grub-customizer, gparted.

[the_eye]

Και ο sdc έχει έναν ανησυχητικό δείκτη

Κώδικας: Επιλογή όλων

199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 1500

Αν τον δεις να ανεβαίνει υπάρχει πρόβλημα.