Samsung smart tv+hdmi+ποντίκι

[kostaspd]

Είμαι ευτυχής κάτοχος μίας Samsung Smart Tv την οποία σύνδεσα με το laptop μου μέσω hdmi...

Επίσης έχω συνδέσει το logitech k400r το οποίο δουλεύει άψογα με την smart tv αλλά το πρόβλημα
μου είναι ότι δεν υπάρχει αλληλεπίδραση μεταξύ του πληκτρολογιού και του ενσωματωμένου toucpad
με το λειτουργικό...

Ο κέρσορας εμφανίζεται κανονικά στην οθόνη αλλά δεν αλληλεπιδρά με το λειτουργικό....

Το ίδιο ισχύει και με την πληκτρολόγηση...

Πως λύνεται αυτό το πρόβλημα???

[the_eye]

Επίσης έχω συνδέσει το logitech k400r το οποίο δουλεύει άψογα με την smart tv

Στην τηλεόραση το σύνδεσες ή στο laptop ;

[kostaspd]

Στο laptop!!!

[lepidas]

εχω το ιδιο και παιζει μια χαρα

[kostaspd]

Σε εμενα ομως γιατι δεν??

[kostaspd]

Κάποια ιδέα ίσως???

Ευχαριστώ...

[the_eye]

Αν το βάλεις μόνο στο laptop, χωρίς την TV λειτουργεί ;
Δώσε μας αποτέλεσμα των

Κώδικας: Επιλογή όλων

lsusb
dmesg

[kostaspd]

Κώδικας: Επιλογή όλων

Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 003: ID 0cf3:311d Atheros Communications, Inc.
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 04f2:b2f4 Chicony Electronics Co., Ltd
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 006: ID 046d:c52b Logitech, Inc. Unifying Receiver
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
kostaspd@hacker:~$


Κώδικας: Επιλογή όλων

[ 6.064137] Key type encrypted registered
[ 6.066748] AppArmor: AppArmor sha1 policy hashing enabled
[ 6.066753] IMA: No TPM chip found, activating TPM-bypass!
[ 6.067270] regulator-dummy: disabling
[ 6.067326] Magic number: 14:62:629
[ 6.067445] rtc_cmos 00:04: setting system clock to 2014-05-19 10:39:03 UTC (1400495943)
[ 6.067607] acpi-cpufreq: overriding BIOS provided _PSD data
[ 6.067760] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 6.067762] EDD information not available.
[ 6.067803] PM: Hibernation image not present or could not be loaded.
[ 6.137057] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 6.142696] ACPI: Battery Slot [BAT0] (battery present)
[ 6.146118] Freeing unused kernel memory: 1332K (ffffffff81d1e000 - ffffffff81e6b000)
[ 6.146123] Write protecting the kernel read-only data: 12288k
[ 6.149809] Freeing unused kernel memory: 844K (ffff88000172d000 - ffff880001800000)
[ 6.153593] Freeing unused kernel memory: 708K (ffff880001b4f000 - ffff880001c00000)
[ 6.172100] systemd-udevd[106]: starting version 204
[ 6.213273] ahci 0000:00:11.0: version 3.0
[ 6.213483] ahci 0000:00:11.0: irq 47 for MSI/MSI-X
[ 6.213547] ahci 0000:00:11.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[ 6.213550] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part sxs
[ 6.214058] scsi0 : ahci
[ 6.214185] scsi1 : ahci
[ 6.214235] ata1: SATA max UDMA/133 abar m2048@0xf0450000 port 0xf0450100 irq 47
[ 6.214239] ata2: SATA max UDMA/133 abar m2048@0xf0450000 port 0xf0450180 irq 47
[ 6.218296] rtsx_pci 0000:04:00.0: irq 48 for MSI/MSI-X
[ 6.218313] rtsx_pci 0000:04:00.0: rtsx_pci_acquire_irq: pcr->msi_en = 1, pci->irq = 48
[ 6.222429] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 6.222946] r8169 0000:05:00.0: irq 49 for MSI/MSI-X
[ 6.223148] r8169 0000:05:00.0 eth0: RTL8105e at 0xffffc9000067a000, a0:b3:cc:77:df:09, XID 00c00000 IRQ 49
[ 6.326021] ACPI Error: [SSZE] Namespace lookup failure, AE_ALREADY_EXISTS (20131115/dsfield-211)
[ 6.326045] ACPI Error: Method parse/execution failed [\_SB_.ACAD._PSR] (Node ffff8801290a6938), AE_ALREADY_EXISTS (20131115/psparse-536)
[ 6.326081] ACPI Exception: AE_ALREADY_EXISTS, Error reading AC Adapter state (20131115/ac-78)
[ 6.333280] ACPI: Marking method _PSR as Serialized because of AE_ALREADY_EXISTS error
[ 6.465184] usb 1-3: new high-speed USB device number 3 using ehci-pci
[ 6.638598] usb 1-3: New USB device found, idVendor=04f2, idProduct=b2f4
[ 6.638610] usb 1-3: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 6.638618] usb 1-3: Product: HP Webcam-50
[ 6.638624] usb 1-3: Manufacturer: Chicony Electronics Co.,Ltd.
[ 6.638630] usb 1-3: SerialNumber: 0x0001
[ 6.661145] tsc: Refined TSC clocksource calibration: 2694.894 MHz
[ 6.705137] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 6.705179] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 6.711444] ata1.00: ATA-9: ST500LM012 HN-M500MBB, 2AR20002, max UDMA/133
[ 6.711457] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 6.717857] ata1.00: configured for UDMA/133
[ 6.717969] ata2.00: ATAPI: hp DVD-RAM UJ8B1, H.04, max UDMA/100
[ 6.718295] scsi 0:0:0:0: Direct-Access ATA ST500LM012 HN-M5 2AR2 PQ: 0 ANSI: 5
[ 6.718815] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 6.718826] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 6.718858] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 6.719146] sd 0:0:0:0: [sda] Write Protect is off
[ 6.719157] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.719247] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.728130] ata2.00: configured for UDMA/100
[ 6.741495] scsi 1:0:0:0: CD-ROM hp DVD-RAM UJ8B1 H.04 PQ: 0 ANSI: 5
[ 6.757664] sda: sda1 sda2 sda3
[ 6.758826] sd 0:0:0:0: [sda] Attached SCSI disk
[ 6.762885] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 6.762890] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 6.763068] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 6.763134] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 7.137723] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 7.165129] usb 4-4: new full-speed USB device number 2 using ohci-pci
[ 7.272351] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.5, id: 0x1e0b1, caps: 0xf00173/0x240000/0xa2400, board id: 2068, fw id: 1028260
[ 7.319457] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input5
[ 7.334354] usb 4-4: New USB device found, idVendor=0cf3, idProduct=311d
[ 7.334366] usb 4-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7.334374] usb 4-4: Product: Bluetooth USB Host Controller
[ 7.334381] usb 4-4: Manufacturer: Atheros Communications
[ 7.334386] usb 4-4: SerialNumber: Alaska Day 2006
[ 7.601251] usb 3-1: new full-speed USB device number 2 using ohci-pci
[ 7.647342] random: init urandom read with 109 bits of entropy available
[ 7.661121] Switched to clocksource tsc
[ 7.776385] usb 3-1: New USB device found, idVendor=045e, idProduct=07b2
[ 7.776398] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 7.776406] usb 3-1: Product: Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0
[ 7.776412] usb 3-1: Manufacturer: Microsoft
[ 7.972659] random: nonblocking pool is initialized
[ 15.964015] Adding 9765884k swap on /dev/sda2. Priority:-1 extents:1 across:9765884k FS
[ 16.079976] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.235562] systemd-udevd[275]: starting version 204
[ 16.419946] lp: driver loaded but no devices found
[ 16.436959] AMD IOMMUv2 driver by Joerg Roedel <joerg.roedel@amd.com>
[ 16.436963] AMD IOMMUv2 functionality not available on this system
[ 16.445019] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[ 16.445024] Disabling lock debugging due to kernel taint
[ 16.449350] ppdev: user-space parallel port driver
[ 16.459846] fglrx: module verification failed: signature and/or required key missing - tainting kernel
[ 16.472738] <6>[fglrx] Maximum main memory to use for locked dma buffers: 3210 MBytes.
[ 16.473016] <6>[fglrx] vendor: 1002 device: 9990 count: 1
[ 16.473450] <6>[fglrx] vendor: 1002 device: 6840 count: 2
[ 16.485844] <6>[fglrx] ioport: bar 1, base 0x4000, size: 0x100
[ 16.536234] <6>[fglrx] ioport: bar 4, base 0x3000, size: 0x100
[ 16.536248] pci 0000:01:00.0: enabling device (0000 -> 0003)
[ 16.541317] <6>[fglrx] Kernel PAT support is enabled
[ 16.541359] <6>[fglrx] module loaded - fglrx 13.35.5 [Mar 12 2014] with 2 minors
[ 16.546711] hp_accel: laptop model unknown, using default axes configuration
[ 16.590467] lis3lv02d: 8 bits 3DC sensor found
[ 16.602502] wmi: Mapper loaded
[ 16.624320] cfg80211: Calling CRDA to update world regulatory domain
[ 16.641717] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input6
[ 16.642637] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 16.654249] Bluetooth: Core ver 2.17
[ 16.654281] NET: Registered protocol family 31
[ 16.654283] Bluetooth: HCI device and connection manager initialized
[ 16.654295] Bluetooth: HCI socket layer initialized
[ 16.654298] Bluetooth: L2CAP socket layer initialized
[ 16.654311] Bluetooth: SCO socket layer initialized
[ 16.656272] usbcore: registered new interface driver btusb
[ 16.663485] acpi device:01: registered as cooling_device2
[ 16.663567] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input7
[ 16.663734] ACPI: Video Device [VGA1] (multi-head: yes rom: no post: no)
[ 16.665541] acpi device:07: registered as cooling_device3
[ 16.665631] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:06/LNXVIDEO:01/input/input8
[ 16.689130] hda-intel 0000:00:01.1: Using LPIB position fix
[ 16.689135] hda-intel 0000:00:01.1: Force to non-snoop mode
[ 16.689176] snd_hda_intel 0000:00:01.1: irq 50 for MSI/MSI-X
[ 16.693116] hda-intel 0000:00:01.1: Enable sync_write for stable communication
[ 16.739598] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.1/sound/card0/input9
[ 16.740140] hda-intel 0000:00:14.2: Using LPIB position fix
[ 16.746546] ath: phy0: ASPM enabled: 0x43
[ 16.746552] ath: EEPROM regdomain: 0x60
[ 16.746554] ath: EEPROM indicates we should expect a direct regpair map
[ 16.746561] ath: Country alpha2 being used: 00
[ 16.746562] ath: Regpair used: 0x60
[ 16.747681] hda-intel 0000:00:14.2: Enable sync_write for stable communication
[ 16.764534] mute LED gpio 10 polarity 0
[ 16.764719] autoconfig: line_outs=1 (0xd/0x0/0x0/0x0/0x0) type:speaker
[ 16.764722] speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 16.764724] hp_outs=1 (0xb/0x0/0x0/0x0/0x0)
[ 16.764726] mono: mono_out=0x0
[ 16.764727] inputs:
[ 16.764729] Internal Mic=0x11
[ 16.764731] Mic=0xc
[ 16.765294] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 16.765842] ieee80211 phy0: Atheros AR9485 Rev:1 mem=0xffffc90005100000, irq=16
[ 16.777684] input: HD-Audio Generic Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input11
[ 16.777950] input: HD-Audio Generic Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input10
[ 16.778375] ACPI Warning: 0x0000000000000b00-0x0000000000000b07 SystemIO conflicts with Region \_SB_.PCI0.SMBS.SMB0 1 (20131115/utaddress-251)
[ 16.778380] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 16.938153] kvm: disabled by bios
[ 16.960985] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 17.067291] type=1400 audit(1400495954.496:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=365 comm="apparmor_parser"
[ 17.067296] type=1400 audit(1400495954.496:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=365 comm="apparmor_parser"
[ 17.067300] type=1400 audit(1400495954.496:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=365 comm="apparmor_parser"
[ 17.067727] type=1400 audit(1400495954.496:5): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=365 comm="apparmor_parser"
[ 17.067732] type=1400 audit(1400495954.496:6): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=365 comm="apparmor_parser"
[ 17.067948] type=1400 audit(1400495954.496:7): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=365 comm="apparmor_parser"
[ 17.069942] type=1400 audit(1400495954.500:8): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=398 comm="apparmor_parser"
[ 17.069948] type=1400 audit(1400495954.500:9): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=398 comm="apparmor_parser"
[ 17.069952] type=1400 audit(1400495954.500:10): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=398 comm="apparmor_parser"
[ 17.070380] type=1400 audit(1400495954.500:11): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=398 comm="apparmor_parser"
[ 17.158222] input: HP WMI hotkeys as /devices/virtual/input/input12
[ 17.297742] hidraw: raw HID events driver (C) Jiri Kosina
[ 17.307154] usb 4-4: USB disconnect, device number 2
[ 17.309674] usbcore: registered new interface driver ath3k
[ 17.329496] Linux video capture interface: v2.00
[ 17.335761] usbcore: registered new interface driver usbhid
[ 17.335765] usbhid: USB HID core driver
[ 17.341072] uvcvideo: Found UVC 1.00 device HP Webcam-50 (04f2:b2f4)
[ 17.356872] input: HP Webcam-50 as /devices/pci0000:00/0000:00:12.2/usb1/1-3/1-3:1.0/input/input13
[ 17.356970] usbcore: registered new interface driver uvcvideo
[ 17.356972] USB Video Class driver (1.1.1)
[ 17.411455] cfg80211: World regulatory domain updated:
[ 17.411462] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 17.411465] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 17.411469] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 17.411471] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 17.411473] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 17.411476] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 17.437489] input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0 as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.0/input/input14
[ 17.437636] hid-generic 0003:045E:07B2.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0] on usb-0000:00:12.0-1/input0
[ 17.438011] input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0 as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.1/input/input15
[ 17.438118] hid-generic 0003:045E:07B2.0002: input,hidraw1: USB HID v1.11 Mouse [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0] on usb-0000:00:12.0-1/input1
[ 17.455337] input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0 as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.2/input/input16
[ 17.455590] hid-generic 0003:045E:07B2.0003: input,hiddev0,hidraw2: USB HID v1.11 Device [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0] on usb-0000:00:12.0-1/input2
[ 17.701691] usb 4-4: new full-speed USB device number 3 using ohci-pci
[ 18.104425] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 19.251785] init: failsafe main process (615) killed by TERM signal
[ 19.938692] init: cups main process (737) killed by HUP signal
[ 19.938709] init: cups main process ended, respawning
[ 20.043462] Bluetooth: RFCOMM TTY layer initialized
[ 20.043478] Bluetooth: RFCOMM socket layer initialized
[ 20.043490] Bluetooth: RFCOMM ver 1.11
[ 20.094223] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 20.094229] Bluetooth: BNEP filters: protocol multicast
[ 20.094242] Bluetooth: BNEP socket layer initialized
[ 21.527446] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 21.534332] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 21.594067] init: plymouth-upstart-bridge main process ended, respawning
[ 21.902157] r8169 0000:05:00.0 eth0: link down
[ 21.902215] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 21.902981] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.839968] init: plymouth-stop pre-start process (1065) terminated with status 1
[ 22.874641] usb 4-4: New USB device found, idVendor=0cf3, idProduct=311d
[ 22.874646] usb 4-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 22.874648] usb 4-4: Product: Bluetooth USB Host Controller
[ 22.874650] usb 4-4: Manufacturer: Atheros Communications
[ 22.874652] usb 4-4: SerialNumber: Alaska Day 2006
[ 23.520092] init: samba-ad-dc main process (1048) terminated with status 1
[ 23.860190] wlan0: authenticate with 84:74:2a:5b:4e:66
[ 23.882473] wlan0: send auth to 84:74:2a:5b:4e:66 (try 1/3)
[ 23.894745] wlan0: authenticated
[ 23.898345] wlan0: associate with 84:74:2a:5b:4e:66 (try 1/3)
[ 23.908789] wlan0: RX AssocResp from 84:74:2a:5b:4e:66 (capab=0x431 status=0 aid=2)
[ 23.908842] wlan0: associated
[ 23.908878] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 23.908944] cfg80211: Calling CRDA for country: GR
[ 23.912537] ath: EEPROM regdomain: 0x812c
[ 23.912543] ath: EEPROM indicates we should expect a country code
[ 23.912544] ath: doing EEPROM country->regdmn map search
[ 23.912546] ath: country maps to regdmn code: 0x37
[ 23.912549] ath: Country alpha2 being used: GR
[ 23.912550] ath: Regpair used: 0x37
[ 23.912552] ath: regdomain 0x812c dynamically updated by country IE
[ 23.912570] cfg80211: Regulatory domain changed to country: GR
[ 23.912572] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 23.912575] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 23.912577] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 23.912579] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 23.912581] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[ 23.912583] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 23.922122] init: udev-fallback-graphics main process (1088) terminated with status 1
[ 24.170017] init: plymouth-splash main process (1129) terminated with status 1
[ 24.366876] wlan0: deauthenticating from 84:74:2a:5b:4e:66 by local choice (reason=2)
[ 24.374981] fglrx_pci 0000:00:01.0: irq 51 for MSI/MSI-X
[ 24.375889] <6>[fglrx] Firegl kernel thread PID: 1139
[ 24.375979] <6>[fglrx] Firegl kernel thread PID: 1140
[ 24.376064] <6>[fglrx] Firegl kernel thread PID: 1141
[ 24.376168] <6>[fglrx] IRQ 51 Enabled
[ 24.381155] <6>[fglrx] Reserved FB block: Shared offset:0, size:1000000
[ 24.381159] <6>[fglrx] Reserved FB block: Unshared offset:fc47000, size:3000
[ 24.381161] <6>[fglrx] Reserved FB block: Unshared offset:fc4a000, size:3b6000
[ 24.381163] <6>[fglrx] Reserved FB block: Unshared offset:1ffee000, size:12000
[ 24.382034] cfg80211: Calling CRDA to update world regulatory domain
[ 24.387860] cfg80211: World regulatory domain updated:
[ 24.387865] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 24.387868] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 24.387870] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 24.387872] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 24.387874] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 24.387876] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 24.398701] wlan0: authenticate with 84:74:2a:5b:4e:66
[ 24.416748] wlan0: send auth to 84:74:2a:5b:4e:66 (try 1/3)
[ 24.426953] wlan0: authenticated
[ 24.429997] wlan0: associate with 84:74:2a:5b:4e:66 (try 1/3)
[ 24.439769] wlan0: RX AssocResp from 84:74:2a:5b:4e:66 (capab=0x431 status=0 aid=2)
[ 24.439817] wlan0: associated
[ 24.439861] cfg80211: Calling CRDA for country: GR
[ 24.443564] ath: EEPROM regdomain: 0x812c
[ 24.443569] ath: EEPROM indicates we should expect a country code
[ 24.443572] ath: doing EEPROM country->regdmn map search
[ 24.443574] ath: country maps to regdmn code: 0x37
[ 24.443577] ath: Country alpha2 being used: GR
[ 24.443579] ath: Regpair used: 0x37
[ 24.443582] ath: regdomain 0x812c dynamically updated by country IE
[ 24.443599] cfg80211: Regulatory domain changed to country: GR
[ 24.443601] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 24.443604] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 24.443606] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 24.443609] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 24.443611] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[ 24.443613] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 30.180071] fglrx_pci 0000:01:00.0: irq 52 for MSI/MSI-X
[ 30.180709] <6>[fglrx] Firegl kernel thread PID: 1160
[ 30.180786] <6>[fglrx] Firegl kernel thread PID: 1161
[ 30.180852] <6>[fglrx] Firegl kernel thread PID: 1162
[ 30.180960] <6>[fglrx] IRQ 52 Enabled
[ 30.230287] <6>[fglrx] Reserved FB block: Shared offset:0, size:1000000
[ 30.230290] <6>[fglrx] Reserved FB block: Unshared offset:f947000, size:3000
[ 30.230292] <6>[fglrx] Reserved FB block: Unshared offset:f94a000, size:3b6000
[ 30.230294] <6>[fglrx] Reserved FB block: Unshared offset:3fff4000, size:c000
[ 30.319782] vgaarb: this pci device is not a vga device
[ 30.319811] vgaarb: this pci device is not a vga device
[ 30.319824] vgaarb: this pci device is not a vga device
[ 30.319837] vgaarb: this pci device is not a vga device
[ 30.319850] vgaarb: this pci device is not a vga device
[ 30.319862] vgaarb: this pci device is not a vga device
[ 30.319875] vgaarb: this pci device is not a vga device
[ 30.319889] vgaarb: this pci device is not a vga device
[ 30.319902] vgaarb: this pci device is not a vga device
[ 30.319915] vgaarb: this pci device is not a vga device
[ 30.319929] vgaarb: this pci device is not a vga device
[ 30.319943] vgaarb: this pci device is not a vga device
[ 30.319957] vgaarb: this pci device is not a vga device
[ 30.319970] vgaarb: this pci device is not a vga device
[ 30.319986] vgaarb: this pci device is not a vga device
[ 30.320001] vgaarb: this pci device is not a vga device
[ 30.320016] vgaarb: this pci device is not a vga device
[ 30.320031] vgaarb: this pci device is not a vga device
[ 30.320046] vgaarb: this pci device is not a vga device
[ 30.320061] vgaarb: this pci device is not a vga device
[ 30.320077] vgaarb: this pci device is not a vga device
[ 30.320093] vgaarb: this pci device is not a vga device
[ 30.320109] vgaarb: this pci device is not a vga device
[ 30.320135] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=none
[ 30.320164] vgaarb: this pci device is not a vga device
[ 30.320182] vgaarb: this pci device is not a vga device
[ 30.320200] vgaarb: this pci device is not a vga device
[ 30.324975] <6>[fglrx] ATIF platform detected with notification ID: 0x81
[ 30.414743] <6>[fglrx] ATIF platform detected with notification ID: 0x81
[ 49.835691] audit_printk_skb: 168 callbacks suppressed
[ 49.835695] type=1400 audit(1400495992.750:68): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=1929 comm="apparmor_parser"
[ 49.835702] type=1400 audit(1400495992.750:69): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=1929 comm="apparmor_parser"
[ 49.836087] type=1400 audit(1400495992.750:70): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=1929 comm="apparmor_parser"
[ 438.076215] systemd-hostnamed[2502]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname!
[ 691.511272] usb 3-1: USB disconnect, device number 2
[ 701.161580] usb 3-1: new full-speed USB device number 3 using ohci-pci
[ 701.336925] usb 3-1: New USB device found, idVendor=045e, idProduct=07b2
[ 701.336935] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 701.336940] usb 3-1: Product: Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0
[ 701.336944] usb 3-1: Manufacturer: Microsoft
[ 701.344613] input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0 as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.0/input/input17
[ 701.344945] hid-generic 0003:045E:07B2.0004: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0] on usb-0000:00:12.0-1/input0
[ 701.352388] input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0 as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.1/input/input18
[ 701.352632] hid-generic 0003:045E:07B2.0005: input,hidraw1: USB HID v1.11 Mouse [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0] on usb-0000:00:12.0-1/input1
[ 701.380297] input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0 as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.2/input/input19
[ 701.380923] hid-generic 0003:045E:07B2.0006: input,hiddev0,hidraw2: USB HID v1.11 Device [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0] on usb-0000:00:12.0-1/input2
[ 1339.616612] type=1400 audit(1400497282.455:71): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=2936 comm="apparmor_parser"
[ 1339.616623] type=1400 audit(1400497282.455:72): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2936 comm="apparmor_parser"
[ 1339.617298] type=1400 audit(1400497282.455:73): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2936 comm="apparmor_parser"
[ 2781.289732] usb 3-1: USB disconnect, device number 3
[ 2868.911984] usb 3-1: new full-speed USB device number 4 using ohci-pci
[ 2869.087034] usb 3-1: New USB device found, idVendor=045e, idProduct=07b2
[ 2869.087043] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2869.087048] usb 3-1: Product: Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0
[ 2869.087052] usb 3-1: Manufacturer: Microsoft
[ 2869.094722] input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0 as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.0/input/input20
[ 2869.094927] hid-generic 0003:045E:07B2.0007: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0] on usb-0000:00:12.0-1/input0
[ 2869.102628] input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0 as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.1/input/input21
[ 2869.103427] hid-generic 0003:045E:07B2.0008: input,hidraw1: USB HID v1.11 Mouse [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0] on usb-0000:00:12.0-1/input1
[ 2869.127397] input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0 as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.2/input/input22
[ 2869.127835] hid-generic 0003:045E:07B2.0009: input,hiddev0,hidraw2: USB HID v1.11 Device [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0] on usb-0000:00:12.0-1/input2
[ 3171.119465] usb 3-1: USB disconnect, device number 4
[ 3233.085141] usb 3-1: new full-speed USB device number 5 using ohci-pci
[ 3233.259795] usb 3-1: New USB device found, idVendor=045e, idProduct=07b2
[ 3233.259804] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3233.259809] usb 3-1: Product: Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0
[ 3233.259814] usb 3-1: Manufacturer: Microsoft
[ 3233.267469] input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0 as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.0/input/input23
[ 3233.267783] hid-generic 0003:045E:07B2.000A: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0] on usb-0000:00:12.0-1/input0
[ 3233.275280] input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0 as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.1/input/input24
[ 3233.275679] hid-generic 0003:045E:07B2.000B: input,hidraw1: USB HID v1.11 Mouse [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0] on usb-0000:00:12.0-1/input1
[ 3233.302084] input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0 as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.2/input/input25
[ 3233.302526] hid-generic 0003:045E:07B2.000C: input,hiddev0,hidraw2: USB HID v1.11 Device [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Nano Transceiver v1.0] on usb-0000:00:12.0-1/input2
[13526.585723] perf samples too long (2501 > 2500), lowering kernel.perf_event_max_sample_rate to 50000
[28407.634006] usb 3-1: USB disconnect, device number 5
[28431.150286] usb 3-1: new full-speed USB device number 6 using ohci-pci
[28431.323272] usb 3-1: New USB device found, idVendor=046d, idProduct=c52b
[28431.323281] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[28431.323286] usb 3-1: Product: USB Receiver
[28431.323290] usb 3-1: Manufacturer: Logitech
[28431.419050] logitech-djreceiver 0003:046D:C52B.000F: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:12.0-1/input2
[28431.423937] input: Logitech Unifying Device. Wireless PID:4024 as /devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.2/0003:046D:C52B.000F/input/input26
[28431.424960] logitech-djdevice 0003:046D:C52B.0010: input,hidraw1: USB HID v1.11 Keyboard [Logitech Unifying Device. Wireless PID:4024] on usb-0000:00:12.0-1:1
kostaspd@hacker:~$


Το σύνδεσα στο laptop και δουλευει κανονικά αλλά ο κέρσορας αναβοσβύνει πολύ γρήγορα...

[the_eye]

Έχεις και κανένα άλλο πληκτρολόγιο ή ποντίκι συνδεδεμένο ;

[kostaspd]

Καλημέρα!Αυτή την στιγμή έχω συνδεδεμένο μόνο το logitech πληκτρολόγιο όπως μου είπατε...
Έχω αποσυνδέσει το ποντίκι της microsoft που είχα συνδεδεμένο πριν συνδέσω το logitech πληκτρολόγιο...