atomo έγραψε:
κατι αλλο ... πως μπορω να απενεργοποιησω το login screen η να αλλαξω θεμα??
οτι αλλαγες κανω χανονται μολις κλεισω το παραθυρο...
Όσον αφορά το login screen είναι ένα προβληματάκι που είχα παρατηρήσει (και είχα γράψει και τη λύση στη σελίδα του Workbench, αλλά με την αλλαγή ονόματος και site ξέχασα να τη ξαναγράψω
....):
Άνοιξε το thunar ως root:
- Κώδικας: Επιλογή όλων
gksu thunar
πήγαινε στο
/etc/gdm και δες αν υπάρχει το αρχείο
gdm.conf-customΑν δεν υπάρχει δημιούργησε ένα αρχείο κειμένου με τα παρακάτω περιεχόμενα, αποθήκευσέ το ως
gdm.conf-custom και αντέγραψέ το στο
/etc/gdm :
- Κώδικας: Επιλογή όλων
# GDM Configuration Customization file.
#
# This file is the appropriate place for specifying your customizations to the
# GDM configuration. If you run gdmsetup, it will automatically edit this
# file for you and will cause the daemon and any running GDM GUI programs to
# automatically update with the new configuration. Not all configuration
# options are supported by gdmsetup, so to modify some values it may be
# necessary to modify this file directly by hand.
#
# Older versions of GDM used the "gdm.conf" file for configuration. If your
# system has an old gdm.conf file on the system, it will be used instead of
# this file - so changes made to this file will not take effect. Consider
# migrating your configuration to this file and removing the gdm.conf file.
#
# To hand-edit this file, simply add or modify the key=value combination in
# the appropriate section in the template below. Refer to the comments in the
# /usr/share/gdm/defaults.conf file for information about each option. Also
# refer to the reference documentation.
#
# If you hand edit a GDM configuration file, you should run the following
# command to get the GDM daemon to notice the change. Any running GDM GUI
# programs will also be notified to update with the new configuration.
#
# gdmflexiserver --command="UPDATE_CONFIG <configuration key>"
#
# e.g, the "Enable" key in the "[debug]" section would be "debug/Enable".
#
# You can also run gdm-restart or gdm-safe-restart to cause GDM to restart and
# re-read the new configuration settings. You can also restart GDM by sending
# a HUP or USR1 signal to the daemon. HUP behaves like gdm-restart and causes
# any user session started by GDM to exit immediately while USR1 behaves like
# gdm-safe-restart and will wait until all users log out before restarting GDM.
#
# For full reference documentation see the gnome help browser under
# GNOME|System category. You can also find the docs in HTML form on
# http://www.gnome.org/projects/gdm/
#
# NOTE: Lines that begin with "#" are considered comments.
#
# Have fun!
[daemon]
[security]
[xdmcp]
[gui]
[greeter]
GraphicalThemes=happygnome/:circles
GraphicalThemedColor=#ffffff
[chooser]
[debug]
[servers]
Πλέον πρέπει να μπορείς να αλλάξεις κανονικά το θέμα του login screen.
