Έλεγχος σκληρού δίσκου Hardware

[freefour]

Eδω ειναι ο πρωτος δισκος dev/sda:
View output:

Κώδικας: Επιλογή όλων

smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.5.0-25-generic] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA DT01ACA050
Serial Number: Z2CZBASFS
LU WWN Device Id: 5 000039 ff2cdcdba
Firmware Version: MS1OA750
User Capacity: 500,106,780,160 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Tue Feb 26 12:10:03 2013 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 5160) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 86) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 136 136 054 Pre-fail Offline - 91
3 Spin_Up_Time 0x0007 134 134 024 Pre-fail Always - 168 (Average 174)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 78
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 115 115 020 Pre-fail Offline - 34
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 334
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 78
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 84
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 84
194 Temperature_Celsius 0x0002 187 187 000 Old_age Always - 32 (Min/Max 12/34)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0

SMART Error Log Version: 1
ATA Error Count: 11 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 11 occurred at disk power-on lifetime: 277 hours (11 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 f1 0f 0d 38 0a Error: UNC 241 sectors at LBA = 0x0a380d0f = 171445519

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 00 0d 38 e0 08 16:18:24.666 READ DMA EXT
25 00 e0 00 14 4c e0 08 16:18:24.665 READ DMA EXT
25 00 20 e0 12 4c e0 08 16:18:24.665 READ DMA EXT
25 00 00 00 13 4c e0 08 16:18:24.664 READ DMA EXT
25 00 e0 00 12 4c e0 08 16:18:24.664 READ DMA EXT

Error 10 occurred at disk power-on lifetime: 274 hours (11 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 ee 57 38 0a Error: UNC 1 sectors at LBA = 0x0a3857ee = 171464686

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 07 e8 57 38 e0 08 13:44:31.562 READ DMA EXT
25 00 08 00 10 4c e0 08 13:44:00.018 READ DMA EXT
25 00 08 08 10 4c e0 08 13:44:00.018 READ DMA EXT
25 00 08 00 10 4c e0 08 13:44:00.011 READ DMA EXT
25 00 08 f0 4f 38 e0 08 13:44:00.011 READ DMA EXT

Error 9 occurred at disk power-on lifetime: 202 hours (8 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 07 10 4c 0d Error: UNC 1 sectors at LBA = 0x0d4c1007 = 223088647

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 00 10 4c e0 08 02:51:12.972 READ DMA EXT
25 00 08 f0 4f 38 e0 08 02:51:12.956 READ DMA EXT
25 00 08 80 4f 38 e0 08 02:51:12.956 READ DMA EXT
c8 00 08 00 28 03 e0 08 02:51:12.956 READ DMA
c8 00 08 08 28 03 e0 08 02:51:12.956 READ DMA

Error 8 occurred at disk power-on lifetime: 179 hours (7 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 07 10 4c 0d Error: UNC 1 sectors at LBA = 0x0d4c1007 = 223088647

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 00 10 4c e0 08 06:08:43.989 READ DMA EXT
25 00 08 f0 4f 38 e0 08 06:08:43.989 READ DMA EXT
25 00 08 80 4f 38 e0 08 06:08:43.989 READ DMA EXT
c8 00 08 00 28 03 e0 08 06:08:43.989 READ DMA
c8 00 08 08 28 03 e0 08 06:08:43.989 READ DMA

Error 7 occurred at disk power-on lifetime: 156 hours (6 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 f7 07 4c 0d Error: UNC 1 sectors at LBA = 0x0d4c07f7 = 223086583

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f0 07 4c e0 08 07:16:27.334 READ DMA EXT
25 00 08 80 07 4c e0 08 07:16:27.334 READ DMA EXT
c8 00 08 00 08 00 e0 08 07:16:27.333 READ DMA
c8 00 08 08 08 00 e0 08 07:16:27.333 READ DMA
c8 00 08 00 08 00 e0 08 07:16:27.333 READ DMA

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 334 -
# 2 Short offline Completed without error 00% 41 -
# 3 Extended offline Completed without error 00% 26 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Κώδικας: Επιλογή όλων

Complete error log:

SMART Error Log Version: 1
ATA Error Count: 11 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 11 occurred at disk power-on lifetime: 277 hours (11 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 f1 0f 0d 38 0a Error: UNC 241 sectors at LBA = 0x0a380d0f = 171445519

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 00 0d 38 e0 08 16:18:24.666 READ DMA EXT
25 00 e0 00 14 4c e0 08 16:18:24.665 READ DMA EXT
25 00 20 e0 12 4c e0 08 16:18:24.665 READ DMA EXT
25 00 00 00 13 4c e0 08 16:18:24.664 READ DMA EXT
25 00 e0 00 12 4c e0 08 16:18:24.664 READ DMA EXT

Error 10 occurred at disk power-on lifetime: 274 hours (11 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 ee 57 38 0a Error: UNC 1 sectors at LBA = 0x0a3857ee = 171464686

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 07 e8 57 38 e0 08 13:44:31.562 READ DMA EXT
25 00 08 00 10 4c e0 08 13:44:00.018 READ DMA EXT
25 00 08 08 10 4c e0 08 13:44:00.018 READ DMA EXT
25 00 08 00 10 4c e0 08 13:44:00.011 READ DMA EXT
25 00 08 f0 4f 38 e0 08 13:44:00.011 READ DMA EXT

Error 9 occurred at disk power-on lifetime: 202 hours (8 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 07 10 4c 0d Error: UNC 1 sectors at LBA = 0x0d4c1007 = 223088647

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 00 10 4c e0 08 02:51:12.972 READ DMA EXT
25 00 08 f0 4f 38 e0 08 02:51:12.956 READ DMA EXT
25 00 08 80 4f 38 e0 08 02:51:12.956 READ DMA EXT
c8 00 08 00 28 03 e0 08 02:51:12.956 READ DMA
c8 00 08 08 28 03 e0 08 02:51:12.956 READ DMA

Error 8 occurred at disk power-on lifetime: 179 hours (7 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 07 10 4c 0d Error: UNC 1 sectors at LBA = 0x0d4c1007 = 223088647

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 00 10 4c e0 08 06:08:43.989 READ DMA EXT
25 00 08 f0 4f 38 e0 08 06:08:43.989 READ DMA EXT
25 00 08 80 4f 38 e0 08 06:08:43.989 READ DMA EXT
c8 00 08 00 28 03 e0 08 06:08:43.989 READ DMA
c8 00 08 08 28 03 e0 08 06:08:43.989 READ DMA

Error 7 occurred at disk power-on lifetime: 156 hours (6 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 f7 07 4c 0d Error: UNC 1 sectors at LBA = 0x0d4c07f7 = 223086583

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f0 07 4c e0 08 07:16:27.334 READ DMA EXT
25 00 08 80 07 4c e0 08 07:16:27.334 READ DMA EXT
c8 00 08 00 08 00 e0 08 07:16:27.333 READ DMA
c8 00 08 08 08 00 e0 08 07:16:27.333 READ DMA
c8 00 08 00 08 00 e0 08 07:16:27.333 READ DMA

[fkol k4]

Μια χαρά είναι ο δίσκος, αλλά βάζεις λάθος φωτογραφία (τσέκαρε ξανά εδώ, το έχουμε πει ξανά).
Επίσης, δεν χρειάζεται το error log και η φωτογραφία μαζί, το ένα από τα δύο είναι αρκετό.

[Learner]

Αυτη τι στιγμη σκαναρω τους δισκους μου με την αργη επιλογη, Extentend Self-test του GSmartControl για να σας δωσω το αποτελεσμα μηπως μπορεσουμε να δουμε τυχων σφαλματα.

Δεν είναι ανάγκη να τρέξεις αυτά τα μεγάλα τεστ για να δεις αν θα τα περάσει ή όχι.
Μια εντολή δίνεις (στην περίπτωση σου 2 , μια για κάθε δίσκο) .

Κώδικας: Επιλογή όλων

sudo smartctl -a /dev/sda
sudo smartctl -a /dev/sdb

και είσαι Ok.
Τα μεγάλα τεστ χρησιμεύουν σε άλλα πράγματα (π.χ όταν οι παραπάνω εντολές δείχνουν Οκ , αλλά παρόλα αυτά πιστεύουμε πως ο δίσκος έχει πρόβλημα).

Μια διακοπή (ή πολλαπλές διακοπές) ρεύματος μπορούν να επηρεάσουν πολλά πράγματα , όχι μόνον τους δίσκους. Τροφοδοτικό - μνήμες - μητρική ... τα πάντα είναι ηλεκτρονικά.. καταλαβαίνεις. Το πιο επικίνδυνο δε (κατά τη γνώμη μου) είναι οι διακυμάνσεις του ηλεκτρικού ρεύματος . Σπάνια συμβαίνει βέβαια , αλλά σε αυτή την περίπτωση μάλλον "κάηκες".
Επίσης τα περισσότερα σύγχρονα τροφοδοτικά έχουν προστασία από τέτοιες περιπτώσεις. (Δεν ξέρω τι τροφοδοτικό έχεις).
Ίσως να έχει γίνει απλά corrupted το σύστημα αρχείων .. και να μην συμβαίνει κάτι άλλο σοβαρότερο.

Μια σκέψη θα ήταν να δώσεις 8-10 ευρώ και να πάρεις μια πρίζα ασφαλείας για τέτοιες περιπτώσεις. Τυχαίο παράδειγμα τέτοιας πρίζας η εικόνα παρακάτω.

[freefour]

Κώδικας: Επιλογή όλων

freefour@freefour-EX58-DS4:~$ sudo smartctl -a /dev/sda
[sudo] password for freefour:
smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.5.0-25-generic] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA DT01ACA050
Serial Number: Z2CZBASFS
LU WWN Device Id: 5 000039 ff2cdcdba
Firmware Version: MS1OA750
User Capacity: 500,106,780,160 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Tue Feb 26 13:05:55 2013 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 5160) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 86) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 136 136 054 Pre-fail Offline - 91
3 Spin_Up_Time 0x0007 134 134 024 Pre-fail Always - 168 (Average 174)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 78
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 115 115 020 Pre-fail Offline - 34
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 335
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 78
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 84
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 84
194 Temperature_Celsius 0x0002 193 193 000 Old_age Always - 31 (Min/Max 12/34)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0

SMART Error Log Version: 1
ATA Error Count: 11 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 11 occurred at disk power-on lifetime: 277 hours (11 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 f1 0f 0d 38 0a Error: UNC 241 sectors at LBA = 0x0a380d0f = 171445519

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 00 0d 38 e0 08 16:18:24.666 READ DMA EXT
25 00 e0 00 14 4c e0 08 16:18:24.665 READ DMA EXT
25 00 20 e0 12 4c e0 08 16:18:24.665 READ DMA EXT
25 00 00 00 13 4c e0 08 16:18:24.664 READ DMA EXT
25 00 e0 00 12 4c e0 08 16:18:24.664 READ DMA EXT

Error 10 occurred at disk power-on lifetime: 274 hours (11 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 ee 57 38 0a Error: UNC 1 sectors at LBA = 0x0a3857ee = 171464686

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 07 e8 57 38 e0 08 13:44:31.562 READ DMA EXT
25 00 08 00 10 4c e0 08 13:44:00.018 READ DMA EXT
25 00 08 08 10 4c e0 08 13:44:00.018 READ DMA EXT
25 00 08 00 10 4c e0 08 13:44:00.011 READ DMA EXT
25 00 08 f0 4f 38 e0 08 13:44:00.011 READ DMA EXT

Error 9 occurred at disk power-on lifetime: 202 hours (8 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 07 10 4c 0d Error: UNC 1 sectors at LBA = 0x0d4c1007 = 223088647

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 00 10 4c e0 08 02:51:12.972 READ DMA EXT
25 00 08 f0 4f 38 e0 08 02:51:12.956 READ DMA EXT
25 00 08 80 4f 38 e0 08 02:51:12.956 READ DMA EXT
c8 00 08 00 28 03 e0 08 02:51:12.956 READ DMA
c8 00 08 08 28 03 e0 08 02:51:12.956 READ DMA

Error 8 occurred at disk power-on lifetime: 179 hours (7 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 07 10 4c 0d Error: UNC 1 sectors at LBA = 0x0d4c1007 = 223088647

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 00 10 4c e0 08 06:08:43.989 READ DMA EXT
25 00 08 f0 4f 38 e0 08 06:08:43.989 READ DMA EXT
25 00 08 80 4f 38 e0 08 06:08:43.989 READ DMA EXT
c8 00 08 00 28 03 e0 08 06:08:43.989 READ DMA
c8 00 08 08 28 03 e0 08 06:08:43.989 READ DMA

Error 7 occurred at disk power-on lifetime: 156 hours (6 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 f7 07 4c 0d Error: UNC 1 sectors at LBA = 0x0d4c07f7 = 223086583

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f0 07 4c e0 08 07:16:27.334 READ DMA EXT
25 00 08 80 07 4c e0 08 07:16:27.334 READ DMA EXT
c8 00 08 00 08 00 e0 08 07:16:27.333 READ DMA
c8 00 08 08 08 00 e0 08 07:16:27.333 READ DMA
c8 00 08 00 08 00 e0 08 07:16:27.333 READ DMA

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 334 -
# 2 Short offline Completed without error 00% 41 -
# 3 Extended offline Completed without error 00% 26 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

freefour@freefour-EX58-DS4:~$


dev/sdb:

Κώδικας: Επιλογή όλων

freefour@freefour-EX58-DS4:~$ sudo smartctl -a /dev/sdb
[sudo] password for freefour:
smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.5.0-25-generic] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K1000.D
Device Model: Hitachi HDS721050DLE630
Serial Number: MSK421Y21P1KZF
LU WWN Device Id: 5 000cca 37fd7a93a
Firmware Version: MS1OA650
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Tue Feb 26 13:08:04 2013 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 25) The self-test routine was aborted by
the host.
Total time to complete Offline
data collection: ( 5451) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 91) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 099 099 016 Pre-fail Always - 2
2 Throughput_Performance 0x0005 133 133 054 Pre-fail Offline - 102
3 Spin_Up_Time 0x0007 129 129 024 Pre-fail Always - 178 (Average 177)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 94
5 Reallocated_Sector_Ct 0x0033 062 062 005 Pre-fail Always - 861
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 115 115 020 Pre-fail Offline - 34
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 332
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 77
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 2129
193 Load_Cycle_Count 0x0012 099 099 000 Old_age Always - 2129
194 Temperature_Celsius 0x0002 166 166 000 Old_age Always - 36 (Min/Max 13/38)
196 Reallocated_Event_Count 0x0032 053 053 000 Old_age Always - 1031
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 1

SMART Error Log Version: 1
ATA Error Count: 3
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 3 occurred at disk power-on lifetime: 275 hours (11 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 6b 95 7a 40 01 Error: ICRC, ABRT 107 sectors at LBA = 0x01407a95 = 21002901

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
35 00 00 00 79 40 e0 08 00:21:04.740 WRITE DMA EXT
ea 00 00 cf 08 00 a0 08 00:21:00.157 FLUSH CACHE EXT
ca 00 08 c8 08 00 e0 08 00:21:00.155 WRITE DMA
ea 00 00 ff 8e c6 a0 08 00:21:00.147 FLUSH CACHE EXT
35 00 08 f8 8e c6 e0 08 00:21:00.147 WRITE DMA EXT

Error 2 occurred at disk power-on lifetime: 5 hours (0 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 17 29 00 00 Error: UNC 1 sectors at LBA = 0x00002917 = 10519

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 10 29 00 e0 08 00:00:52.704 READ DMA
c8 00 08 78 08 00 e0 08 00:00:52.703 READ DMA
c8 00 08 70 08 00 e0 08 00:00:52.703 READ DMA
c8 00 08 68 08 00 e0 08 00:00:52.703 READ DMA
c8 00 08 60 08 00 e0 08 00:00:52.703 READ DMA

Error 1 occurred at disk power-on lifetime: 1 hours (0 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 31 0f 50 f8 03 Error: UNC 49 sectors at LBA = 0x03f8500f = 66605071

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 40 00 50 f8 e0 08 01:31:40.469 READ DMA EXT
25 00 40 80 27 23 e0 08 01:31:40.467 READ DMA EXT
25 00 38 c0 27 23 e0 08 01:31:40.466 READ DMA EXT
25 00 40 80 87 13 e0 08 01:31:40.466 READ DMA EXT
25 00 38 c0 87 13 e0 08 01:31:40.466 READ DMA EXT

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Aborted by host 90% 332 -
# 2 Short offline Completed without error 00% 42 -
# 3 Extended offline Completed without error 00% 28 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

freefour@freefour-EX58-DS4:~$


Nαι το ξερω ολα ειναι πiθανα να συμβουν με το ρευμα. Εγω ειχα σκοπο να επερνα ups, περυσι καηκε το παλιο και μετα απο λιγο καηκε και το τροφοδοτικο. Τουλαχιστον μια πριζα ασφαλειας θα παρω σιγουρα. Ευχομαι να μην ειναι αργα και να προλαβα κατι σοβαρο με το pc (αν και βλεπω να κρασαρει ακομη.) Θα μπω για λιγο στον αλλο δισκο (sda) να δω πως παει.

[freefour]

Μια χαρά είναι ο δίσκος, αλλά βάζεις λάθος φωτογραφία (τσέκαρε ξανά εδώ, το έχουμε πει ξανά).
Επίσης, δεν χρειάζεται το error log και η φωτογραφία μαζί, το ένα από τα δύο είναι αρκετό.

To θυμαμε αυτο που ειπαμε αλλα φανταστηκα οτι στην περιπτωση αυτη θα χρειαζοταν ολα τα στοιχεια.

[fkol k4]

Κώδικας: Επιλογή όλων

ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0033 062 062 005 Pre-fail Always - 861
196 Reallocated_Event_Count 0x0032 053 053 000 Old_age Always - 1031


O 2ος δίσκος έχει ζημιά, λογικά αφού είναι καινούριος θα πρέπει να μπορείς να τον αλλάξεις μέσα στην εγγύηση

[Learner]

Συγχωνεύτηκαν - μεταφέρθηκαν όλες οι δημοσιεύσεις εδώ => https://forum.ubuntu-gr.org/viewtopic.p ... 28#p278328

Παρακαλώ να συνεχίσουμε εκεί , να μην γεμίζουμε αυτό το νήμα με offtopic.

[adem1]

Εμένα που είναι αυτό

Κώδικας: Επιλογή όλων

Raw_Read_Error_Rate

γύρω στις 16000 να ανυσηχήσω;

[eliasps]

γύρω στις 16000 να ανυσηχήσω;

Τα υπόλοιπα τι λένε;
Δες σε αυτόν τον οδηγό, πως να διαβάζεις αυτά τα δεδομένα και τι σημαίνουν.

[dgtfeargr]

Raw_Read_Error_Rate
γύρω στις 16000 να ανυσηχήσω;

(Συγκεκριμένη τιμή καθορισμένη από τον κατασκευαστή)

Και μένα είναι στα 3721. Αυτή η τιμή καθορίζεται από τον κατασκευαστή ως προεπιλεγμένη. Το θέμα είναι οι υπόλοιπες τιμές να είναι 0 ή να μην αυξάνονται. Μπορείς να αποθηκεύσεις το log σου και να ξανά κάνεις ένα τέστ (πχ. μετά το καλοκαίρι) για να δεις αν αυξήθηκε η τιμή Raw_Read_Error_Rate . Αν ναι τότε υπάρχει πρόβλημα αν όχι θα επιβεβαιώσεις ότι αυτή η τιμή έχει "μπει" από τον κατασκευαστή.