αποτυχία συνδεσης(ουτε ethernet ουτε wireless)

[michalis_pax]

λοιπον παιδια ακουστε το εξης προβλημα(δυσκολο).πριν πεντε μερες αγορασα ενα netbook hp mini 110-3150ev/sv black.το πρωτο πραγμα που εκανα λοιπον ηταν να εγκταστησω το ubuntu 10.10 desktop/laptop edition(το ubuntu netbook δεν μου αρεσουν).στην αρχη δεν μπορουσα να συνδεθω wirless(μου ζητουσε ολο τον κωδικο και δεν με συνεδεε)και γι αυτο συνθεθηκα με ethernet(ειχα σκοπο να ψαξω για τους ποιο προσφατους drivers αργοτερα).τωρα ομως δεν αναγνωριζει ουτε την ethernet συνδεση.αυτο μου φαινεται παραξενο γιατι δεν καταλαβαινω πως το επαθε(δεν πειραξα τις ρυθμισεις).οποιος μορει να βοηθησει(γνωριζω αρκετα καλα το linux
αφου τα χρησειμοποιο και στο desktop και ξερω να δουλευω και απο το τερματικο
(μετρια)).ευχαριστω προκαταβολικα

[the_eye]

Δώσε μας το
ifconfig

[xaris2335]

επίσης δώσε το αποτέλεσμα απο

Κώδικας: Επιλογή όλων

dmesg
lspci -n
lsmod

[michalis_pax]

Εφτιαξα την ethernet συνδεση.Αλλα η wireless δεν λειτουργει ακομη.
το αποτελεσμα της ifconfig ειναι:

Κώδικας: Επιλογή όλων

eth0 Link encap:Ethernet HWaddr 68:b5:99:d7:d4:00
inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::6ab5:99ff:fed7:d400/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:134423 errors:0 dropped:0 overruns:0 frame:0
TX packets:77990 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:198973923 (198.9 MB) TX bytes:5814251 (5.8 MB)
Interrupt:42

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:16 errors:0 dropped:0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:960 (960.0 B) TX bytes:960 (960.0 B)

το αποτελεσμα της dmesg ειναι:

Κώδικας: Επιλογή όλων

[ 0.790116] pci 0000:00:1c.1: bridge window [mem 0x52000000-0x52ffffff]
[ 0.790136] pci 0000:00:1c.1: bridge window [mem 0x51000000-0x51ffffff 64bit pref]
[ 0.790278] pci 0000:00:1e.0: PCI bridge to [bus 03-03] (subtractive decode)
[ 0.790293] pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.790305] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.790322] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.790333] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.790342] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.790352] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.790362] pci 0000:00:1e.0: bridge window [mem 0x40000000-0xfebfffff] (subtractive decode)
[ 0.790428] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.791080] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
[ 0.791638] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[ 0.792026] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
[ 0.792935] ACPI Warning for \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20100428/nspredef-352)
[ 0.792975] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 0.792981] _OSC request data:1 1f 1f
[ 0.805232] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.805682] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12)
[ 0.806147] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.806591] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.807051] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.807548] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.807996] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.808454] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.808682] HEST: Table is not found!
[ 0.808936] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.808973] vgaarb: loaded
[ 0.809465] SCSI subsystem initialized
[ 0.809736] libata version 3.00 loaded.
[ 0.809953] usbcore: registered new interface driver usbfs
[ 0.810029] usbcore: registered new interface driver hub
[ 0.810148] usbcore: registered new device driver usb
[ 0.811165] ACPI: WMI: Mapper loaded
[ 0.811174] PCI: Using ACPI for IRQ routing
[ 0.811184] PCI: pci_cache_line_size set to 64 bytes
[ 0.811399] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.811408] reserve RAM buffer: 000000003f43f000 - 000000003fffffff
[ 0.811419] reserve RAM buffer: 000000003f600000 - 000000003fffffff
[ 0.811722] NetLabel: Initializing
[ 0.811730] NetLabel: domain hash size = 128
[ 0.811735] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.811779] NetLabel: unlabeled traffic allowed by default
[ 0.811905] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.811919] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.811934] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.830111] Switching to clocksource tsc
[ 0.862455] AppArmor: AppArmor Filesystem Enabled
[ 0.862499] pnp: PnP ACPI init
[ 0.862554] ACPI: bus type pnp registered
[ 0.869650] pnp: PnP ACPI: found 9 devices
[ 0.869660] ACPI: ACPI bus type pnp unregistered
[ 0.869699] system 00:01: [io 0x0600-0x060f] has been reserved
[ 0.869709] system 00:01: [io 0x0610] has been reserved
[ 0.869719] system 00:01: [io 0x0800-0x080f] has been reserved
[ 0.869729] system 00:01: [io 0x0810-0x0817] has been reserved
[ 0.869739] system 00:01: [io 0x0400-0x047f] has been reserved
[ 0.869749] system 00:01: [io 0x0500-0x053f] has been reserved
[ 0.869762] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.869772] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.869783] system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
[ 0.869793] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.869804] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.869815] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.869825] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.880029] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.880044] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 0.880058] pci 0000:00:1c.0: bridge window [mem 0x53000000-0x53ffffff]
[ 0.880071] pci 0000:00:1c.0: bridge window [mem 0x50000000-0x50ffffff 64bit pref]
[ 0.880089] pci 0000:00:1c.1: PCI bridge to [bus 02-02]
[ 0.880098] pci 0000:00:1c.1: bridge window [io 0x1000-0x1fff]
[ 0.880112] pci 0000:00:1c.1: bridge window [mem 0x52000000-0x52ffffff]
[ 0.880125] pci 0000:00:1c.1: bridge window [mem 0x51000000-0x51ffffff 64bit pref]
[ 0.880141] pci 0000:00:1e.0: PCI bridge to [bus 03-03]
[ 0.880148] pci 0000:00:1e.0: bridge window [io disabled]
[ 0.880160] pci 0000:00:1e.0: bridge window [mem disabled]
[ 0.880171] pci 0000:00:1e.0: bridge window [mem pref disabled]
[ 0.880211] alloc irq_desc for 16 on node -1
[ 0.880218] alloc kstat_irqs on node -1
[ 0.880238] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.880252] pci 0000:00:1c.0: setting latency timer to 64
[ 0.880274] alloc irq_desc for 17 on node -1
[ 0.880281] alloc kstat_irqs on node -1
[ 0.880294] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.880306] pci 0000:00:1c.1: setting latency timer to 64
[ 0.880325] pci 0000:00:1e.0: setting latency timer to 64
[ 0.880337] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.880346] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.880354] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.880363] pci_bus 0000:00: resource 7 [mem 0x40000000-0xfebfffff]
[ 0.880372] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
[ 0.880380] pci_bus 0000:01: resource 1 [mem 0x53000000-0x53ffffff]
[ 0.880390] pci_bus 0000:01: resource 2 [mem 0x50000000-0x50ffffff 64bit pref]
[ 0.880399] pci_bus 0000:02: resource 0 [io 0x1000-0x1fff]
[ 0.880407] pci_bus 0000:02: resource 1 [mem 0x52000000-0x52ffffff]
[ 0.880416] pci_bus 0000:02: resource 2 [mem 0x51000000-0x51ffffff 64bit pref]
[ 0.880426] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7]
[ 0.880434] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff]
[ 0.880443] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.880451] pci_bus 0000:03: resource 7 [mem 0x40000000-0xfebfffff]
[ 0.880565] NET: Registered protocol family 2
[ 0.880838] IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.882562] TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
[ 0.884651] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.885481] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.885490] TCP reno registered
[ 0.885542] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.885609] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.885923] NET: Registered protocol family 1
[ 0.885975] pci 0000:00:02.0: Boot video device
[ 0.899437] PCI: CLS 64 bytes, default 64
[ 0.899546] Simple Boot Flag at 0x44 set to 0x1
[ 0.900111] Scanning for low memory corruption every 60 seconds
[ 0.900638] audit: initializing netlink socket (disabled)
[ 0.900670] type=2000 audit(1290886047.890:1): initialized
[ 0.903810] Freeing initrd memory: 10748k freed
[ 0.928158] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.931744] VFS: Disk quotas dquot_6.5.2
[ 0.931908] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.933395] fuse init (API version 7.14)
[ 0.933642] msgmni has been set to 1968
[ 0.939721] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.939731] io scheduler noop registered
[ 0.939736] io scheduler deadline registered
[ 0.939850] io scheduler cfq registered (default)
[ 0.940091] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.940155] alloc irq_desc for 40 on node -1
[ 0.940161] alloc kstat_irqs on node -1
[ 0.940182] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[ 0.940375] pcieport 0000:00:1c.1: setting latency timer to 64
[ 0.940434] alloc irq_desc for 41 on node -1
[ 0.940439] alloc kstat_irqs on node -1
[ 0.940456] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
[ 0.940682] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.940999] ACPI Warning for \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20100428/nspredef-352)
[ 0.941028] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 0.941032] _OSC request data:1 0 1f
[ 0.941344] ACPI Warning for \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20100428/nspredef-352)
[ 0.941371] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 0.941375] _OSC request data:1 0 1f
[ 0.941719] ACPI Warning for \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20100428/nspredef-352)
[ 0.941746] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 0.941750] _OSC request data:1 0 1f
[ 0.942054] ACPI Warning for \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20100428/nspredef-352)
[ 0.942080] \_SB_.PCI0:_OSC evaluation returned wrong type
[ 0.942085] _OSC request data:1 0 1f
[ 0.942148] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.942363] intel_idle: MWAIT substates: 0x20220
[ 0.942368] intel_idle: v0.4 model 0x1C
[ 0.942372] intel_idle: lapic_timer_reliable_states 0x6
[ 0.942386] Marking TSC unstable due to TSC halts in idle states deeper than C2
[ 0.942513] Switching to clocksource hpet
[ 0.943847] ACPI: AC Adapter [AC] (off-line)
[ 0.944049] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.944063] ACPI: Power Button [PWRB]
[ 0.944166] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[ 0.945331] ACPI: Lid Switch [LID0]
[ 0.945482] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 0.945493] ACPI: Power Button [PWRF]
[ 0.946252] ACPI: acpi_idle yielding to intel_idleACPI Warning for \_TZ_.THRM._AL0: Return Package has no elements (empty) (20100428/nspredef-456)
[ 0.962448] ACPI: [Package] has zero elements (ffff88003c9de640)
[ 0.962454] ACPI: Invalid active0 threshold
[ 0.966481] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.966502] ACPI: Thermal Zone [THRM] (20 C)
[ 0.966735] ERST: Table is not found!
[ 0.967384] Linux agpgart interface v0.103
[ 0.967486] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.971855] brd: module loaded
[ 0.973767] loop: module loaded
[ 0.975220] Fixed MDIO Bus: probed
[ 0.975334] PPP generic driver version 2.4.2
[ 0.975444] tun: Universal TUN/TAP device driver, 1.6
[ 0.975450] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.975729] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.975782] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.975818] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.975826] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.975982] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 0.976020] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 0.976039] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.979931] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[ 0.979981] ehci_hcd 0000:00:1d.7: irq 16, io mem 0x54204400
[ 1.001276] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.001577] hub 1-0:1.0: USB hub found
[ 1.001591] hub 1-0:1.0: 8 ports detected
[ 1.001767] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.001803] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.001953] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.001976] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.001984] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.002084] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 1.002128] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00003080
[ 1.002422] hub 2-0:1.0: USB hub found
[ 1.002434] hub 2-0:1.0: 2 ports detected
[ 1.002571] alloc irq_desc for 18 on node -1
[ 1.002577] alloc kstat_irqs on node -1
[ 1.002593] uhci_hcd 0000:00:1d.1: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.002606] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.002613] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.002702] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 1.002764] uhci_hcd 0000:00:1d.1: irq 18, io base 0x00003060
[ 1.003070] hub 3-0:1.0: USB hub found
[ 1.003083] hub 3-0:1.0: 2 ports detected
[ 1.003210] uhci_hcd 0000:00:1d.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.003224] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.003231] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.003342] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 1.003400] uhci_hcd 0000:00:1d.2: irq 17, io base 0x00003040
[ 1.003692] hub 4-0:1.0: USB hub found
[ 1.003704] hub 4-0:1.0: 2 ports detected
[ 1.003845] alloc irq_desc for 19 on node -1
[ 1.003851] alloc kstat_irqs on node -1
[ 1.003867] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 1.003880] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 1.003888] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 1.003985] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 1.004049] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00003020
[ 1.004333] hub 5-0:1.0: USB hub found
[ 1.004345] hub 5-0:1.0: 2 ports detected
[ 1.004585] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOUE] at 0x60,0x64 irq 1,12
[ 1.009808] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.009830] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.010072] mice: PS/2 mouse device common for all mice
[ 1.010411] rtc_cmos 00:03: RTC can wake from S4
[ 1.010510] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.010554] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 1.010813] device-mapper: uevent: version 1.0.3
[ 1.011058] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
[ 1.011306] device-mapper: multipath: version 1.1.1 loaded
[ 1.011317] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.011944] cpuidle: using governor ladder
[ 1.012184] cpuidle: using governor menu
[ 1.012839] TCP cubic registered
[ 1.013151] NET: Registered protocol family 10
[ 1.013996] lo: Disabled Privacy Extensions
[ 1.014494] NET: Registered protocol family 17
[ 1.016177] PM: Resume from disk failed.
[ 1.016214] registered taskstats version 1
[ 1.016841] Magic number: 2:4:497
[ 1.017009] rtc_cmos 00:03: setting system clock to 2010-11-27 19:27:28 UTC (1290886048)
[ 1.017018] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.017022] EDD information not available.
[ 1.017254] Freeing unused kernel memory: 908k freed
[ 1.017759] Write protecting the kernel read-only data: 10240k
[ 1.018218] Freeing unused kernel memory: 416k freed
[ 1.018908] Freeing unused kernel memory: 1644k freed
[ 1.062572] udev[75]: starting version 163
[ 1.139268] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 1.430202] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.430275] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.430411] r8169 0000:01:00.0: setting latency timer to 64
[ 1.430433] r8169 0000:01:00.0: (unregistered net_device): unknown MAC, using family default
[ 1.430602] alloc irq_desc for 42 on node -1
[ 1.430610] alloc kstat_irqs on node -1
[ 1.430660] r8169 0000:01:00.0: irq 42 for MSI/MSI-X
[ 1.432451] r8169 0000:01:00.0: eth0: RTL8101e at 0xffffc900001f0000, 68:b5:99:d7:d4:00, XID 04000000 IRQ 42
[ 1.441531] usb 1-8: new high speed USB device using ehci_hcd and address 3
[ 1.447892] ahci 0000:00:1f.2: version 3.0
[ 1.447937] ahci 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.448029] alloc irq_desc for 43 on node -1
[ 1.448037] alloc kstat_irqs on node -1
[ 1.448066] ahci 0000:00:1f.2: irq 43 for MSI/MSI-X
[ 1.448148] ahci: SSS flag set, parallel bus scan disabled
[ 1.448208] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x3 impl SATA mode
[ 1.448221] ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part
[ 1.448235] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.448669] scsi0 : ahci
[ 1.449086] scsi1 : ahci
[ 1.449361] scsi2 : ahci
[ 1.449643] scsi3 : ahci
[ 1.450596] ata1: SATA max UDMA/133 abar m1024@0x54204000 port 0x54204100 irq 43
[ 1.450610] ata2: SATA max UDMA/133 abar m1024@0x54204000 port 0x54204180 irq 43
[ 1.450618] ata3: DUMMY
[ 1.450624] ata4: DUMMY
[ 1.512419] ACPI: Battery Slot [BAT0] (battery present)
[ 1.950131] usb 3-2: new full speed USB device using uhci_hcd and address 2
[ 1.980147] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.981457] ata1.00: unexpected _GTF length (4)
[ 2.019307] ata1.00: ATA-8: WDC WD1600BEVT-22A23T0, 01.01A01, max UDMA/133
[ 2.019320] ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[ 2.020965] ata1.00: unexpected _GTF length (4)
[ 2.021296] ata1.00: configured for UDMA/133
[ 2.040474] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVT-2 01.0 PQ: 0 ANSI: 5
[ 2.040964] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 2.040996] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.041528] sd 0:0:0:0: [sda] Write Protect is off
[ 2.041538] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.041639] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.042199] sda: sda1 sda2 sda3 sda4
[ 2.055982] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.390133] ata2: SATA link down (SStatus 0 SControl 300)
[ 3.448211] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
[ 6.421079] udev[361]: starting version 163
[ 7.973159] input: HP WMI hotkeys as /devices/virtual/input/input4
[ 8.019860] agpgart-intel 0000:00:00.0: Intel GMA3150 Chipset
[ 8.020814] agpgart-intel 0000:00:00.0: detected 8188K stolen memory
[ 8.033950] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x40000000
[ 8.082281] Bluetooth: Core ver 2.15
[ 8.082342] NET: Registered protocol family 31
[ 8.082349] Bluetooth: HCI device and connection manager initialized
[ 8.082357] Bluetooth: HCI socket layer initialized
[ 8.266053] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 8.267636] usbcore: registered new interface driver btusb
[ 8.307329] lp: driver loaded but no devices found
[ 8.351678] Linux video capture interface: v2.00
[ 8.586383] cfg80211: Calling CRDA to update world regulatory domain
[ 8.594554] uvcvideo: Found UVC 1.00 device HP Webcam (174f:1122)
[ 8.608734] input: HP Webcam as /devices/pci0000:00/0000:00:1d.7/usb1/1-8/1-8:1.0/input/input5
[ 8.608951] usbcore: registered new interface driver uvcvideo
[ 8.608960] USB Video Class driver (v0.1.0)
[ 8.863914] type=1400 audit(1290878856.344:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient3" pid=524 comm="apparmor_parser"
[ 8.864734] type=1400 audit(1290878856.344:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=524 comm="apparmor_parser"
[ 8.865206] type=1400 audit(1290878856.344:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=524 comm="apparmor_parser"
[ 8.948352] [drm] Initialized drm 1.1.0 20060810
[ 9.228408] Synaptics Touchpad, model: 1, fw: 7.4, id: 0x1e0b1, caps: 0xd04771/0xa40000/0xa0400
[ 9.273654] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
[ 9.413473] i915 0000:00:02.0: power state changed by ACPI to D0
[ 9.413519] i915 0000:00:02.0: power state changed by ACPI to D0
[ 9.413539] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 9.413551] i915 0000:00:02.0: setting latency timer to 64
[ 9.476095] alloc irq_desc for 44 on node -1
[ 9.476104] alloc kstat_irqs on node -1
[ 9.476123] i915 0000:00:02.0: irq 44 for MSI/MSI-X
[ 9.476146] [drm] set up 7M of stolen space
[ 9.585926] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 9.586291] [drm] initialized overlay support
[ 9.622009] cfg80211: World regulatory domain updated:
[ 9.622018] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.622028] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.622036] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.622043] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.622051] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.622058] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.917774] rt2800pci 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 9.917812] rt2800pci 0000:02:00.0: setting latency timer to 64
[ 9.931342] Skipping EDID probe due to cached edid
[ 10.317834] Console: switching to colour frame buffer device 128x37
[ 10.324412] fb0: inteldrmfb frame buffer device
[ 10.324419] drm: registered panic notifier
[ 10.324445] Slow work thread pool: Starting up
[ 10.324589] Slow work thread pool: Ready
[ 10.332209] acpi device:20: registered as cooling_device2
[ 10.335010] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
[ 10.335494] ACPI: Video Device [OVGA] (multi-head: yes rom: no post: no)
[ 10.336507] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 10.336630] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 10.336731] alloc irq_desc for 45 on node -1
[ 10.336739] alloc kstat_irqs on node -1
[ 10.336770] HDA Intel 0000:00:1b.0: irq 45 for MSI/MSI-X
[ 10.336850] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 10.545500] phy0: Selected rate control algorithm 'minstrel'
[ 10.547307] Registered led device: rt2800pci-phy0::radio
[ 10.547373] Registered led device: rt2800pci-phy0::assoc
[ 10.547438] Registered led device: rt2800pci-phy0::quality
[ 10.830404] input: HDA Intel Mic at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 10.830794] input: HDA Intel HP Out at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 10.985495] rt2860sta: module is from the staging directory, the quality is unknown, you have been warned.
[ 11.151485] Skipping EDID probe due to cached edid
[ 15.975530] Adding 261116k swap on /host/ubuntu/disks/swap.disk. Priority:-1 extents:1 across:261116k
[ 16.062560] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro
[ 16.820824] type=1400 audit(1290878864.294:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=1000 comm="apparmor_parser"
[ 16.821614] type=1400 audit(1290878864.294:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1000 comm="apparmor_parser"
[ 16.822079] type=1400 audit(1290878864.294:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1000 comm="apparmor_parser"
[ 16.839700] type=1400 audit(1290878864.304:8): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=999 comm="apparmor_parser"
[ 16.879497] type=1400 audit(1290878864.344:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1003 comm="apparmor_parser"
[ 16.881303] type=1400 audit(1290878864.354:10): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1003 comm="apparmor_parser"
[ 16.886237] type=1400 audit(1290878864.354:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=1001 comm="apparmor_parser"
[ 16.895958] type=1400 audit(1290878864.364:12): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=1001 comm="apparmor_parser"
[ 16.899053] type=1400 audit(1290878864.364:13): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=1004 comm="apparmor_parser"
[ 16.903029] type=1400 audit(1290878864.374:14): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=1001 comm="apparmor_parser"
[ 17.122191] ppdev: user-space parallel port driver
[ 18.141450] Bluetooth: L2CAP ver 2.14
[ 18.141460] Bluetooth: L2CAP socket layer initialized
[ 18.507388] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 18.507399] Bluetooth: BNEP filters: protocol multicast
[ 18.675890] Bluetooth: SCO (Voice Link) ver 0.6
[ 18.675899] Bluetooth: SCO socket layer initialized
[ 19.105872] Bluetooth: RFCOMM TTY layer initialized
[ 19.105892] Bluetooth: RFCOMM socket layer initialized
[ 19.105899] Bluetooth: RFCOMM ver 1.11
[ 19.441336] r8169 0000:01:00.0: eth0: link up
[ 19.441364] r8169 0000:01:00.0: eth0: link up
[ 19.601560] phy0 -> rt2800pci_load_firmware: Error - PBF system register not ready.
[ 19.602167] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00007010, value=0x2ed6d674
[ 20.040052] phy0 -> rt2800pci_load_firmware: Error - PBF system register not ready.
[ 20.040653] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00007010, value=0x2ed6d674
[ 20.330435] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,commit=600
[ 20.531529] Skipping EDID probe due to cached edid
[ 20.570348] Skipping EDID probe due to cached edid
[ 23.510109] Skipping EDID probe due to cached edid
[ 23.551696] Skipping EDID probe due to cached edid
[ 23.620082] Skipping EDID probe due to cached edid
[ 23.670191] Skipping EDID probe due to cached edid
[ 25.845424] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,commit=600
[ 26.440153] Skipping EDID probe due to cached edid
[ 30.220067] eth0: no IPv6 routers present
[ 54.820240] Skipping EDID probe due to cached edid
[ 54.880231] Skipping EDID probe due to cached edid
[ 54.920208] Skipping EDID probe due to cached edid
[ 54.960182] Skipping EDID probe due to cached edid
[ 55.150357] Skipping EDID probe due to cached edid
[ 58.100206] Skipping EDID probe due to cached edid
[ 61.241407] Skipping EDID probe due to cached edid
[ 296.737311] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,commit=0
[ 296.993368] ata1.00: exception Emask 0x10 SAct 0x1 SErr 0x50000 action 0xe frozen
[ 296.993384] ata1.00: irq_stat 0x00400000, PHY RDY changed
[ 296.993397] ata1: SError: { PHYRdyChg CommWake }
[ 296.993410] ata1.00: failed command: READ FPDMA QUEUED
[ 296.993434] ata1.00: cmd 60/08:00:60:63:0c/00:00:10:00:00/40 tag 0 ncq 4096 in
[ 296.993440] res 40/00:04:60:63:0c/00:00:10:00:00/40 Emask 0x10 (ATA bus error)
[ 296.993452] ata1.00: status: { DRDY }
[ 296.993469] ata1: hard resetting link
[ 297.921454] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 297.922675] ata1.00: unexpected _GTF length (4)
[ 297.924373] ata1.00: unexpected _GTF length (4)
[ 297.924684] ata1.00: configured for UDMA/133
[ 297.924711] ata1: EH complete
[ 435.130091] CE: hpet increased min_delta_ns to 7500 nsec
[ 706.521820] ACPI: EC: GPE storm detected, transactions will use polling mode
[ 911.557345] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 911.567899] SGI XFS Quota Management subsystem
[ 911.662154] JFS: nTxBlock = 7896, nTxLock = 63171
[ 911.748067] NTFS driver 2.1.29 [Flags: R/O MODULE].
[ 911.803448] QNX4 filesystem 0.2.3 registered.
[ 911.935616] Btrfs loaded

το αποτελεσμα της lpci -n ειναι:

Κώδικας: Επιλογή όλων

00:00.0 0600: 8086:a010
00:02.0 0300: 8086:a011
00:02.1 0380: 8086:a012
00:1b.0 0403: 8086:27d8 (rev 02)
00:1c.0 0604: 8086:27d0 (rev 02)
00:1c.1 0604: 8086:27d2 (rev 02)
00:1d.0 0c03: 8086:27c8 (rev 02)
00:1d.1 0c03: 8086:27c9 (rev 02)
00:1d.2 0c03: 8086:27ca (rev 02)
00:1d.3 0c03: 8086:27cb (rev 02)
00:1d.7 0c03: 8086:27cc (rev 02)
00:1e.0 0604: 8086:2448 (rev e2)
00:1f.0 0601: 8086:27bc (rev 02)
00:1f.2 0106: 8086:27c1 (rev 02)
00:1f.3 0c05: 8086:27da (rev 02)
01:00.0 0200: 10ec:8136 (rev 04)
01:00.1 ff00: 10ec:5288 (rev 01)
02:00.0 0280: 1814:3090

και το αποτελεσμα τησ lsmod ειναι:

Κώδικας: Επιλογή όλων

Module Size Used by
nls_iso8859_1 4657 0
nls_cp437 6375 0
btrfs 506518 0
zlib_deflate 21866 1 btrfs
crc32c 3007 1
libcrc32c 1268 1 btrfs
ufs 74447 0
qnx4 8101 0
hfsplus 78159 0
hfs 47396 0
minix 29289 0
ntfs 97516 0
vfat 10954 0
msdos 7960 0
fat 56244 2 vfat,msdos
jfs 183125 0
xfs 766115 0
exportfs 4226 1 xfs
reiserfs 244936 0
rfcomm 40755 4
binfmt_misc 7984 1
sco 9954 2
bnep 11985 2
l2cap 42304 16 rfcomm,bnep
parport_pc 30086 0
ppdev 6804 0
rt2860sta 559618 0
snd_hda_codec_idt 64667 1
arc4 1497 2
snd_hda_intel 26019 2
rt2800pci 10233 0
snd_hda_codec 100919 2 snd_hda_codec_idt,snd_hda_intel
rt2800lib 31970 1 rt2800pci
rt2x00usb 11316 1 rt2800lib
rt2x00pci 6993 1 rt2800pci
snd_hwdep 6660 1 snd_hda_codec
crc_ccitt 1699 2 rt2860sta,rt2800pci
snd_pcm 89104 2 snd_hda_intel,snd_hda_codec
i915 330089 3
snd_seq_midi 5932 0
rt2x00lib 31575 4 rt2800pci,rt2800lib,rt2x00usb,rt2x00pci
joydev 11363 0
snd_rawmidi 22207 1 snd_seq_midi
snd_seq_midi_event 7291 1 snd_seq_midi
snd_seq 57512 2 snd_seq_midi,snd_seq_midi_event
led_class 3393 1 rt2x00lib
snd_timer 23850 2 snd_pcm,snd_seq
drm_kms_helper 32836 1 i915
mac80211 266657 3 rt2x00usb,rt2x00pci,rt2x00lib
snd_seq_device 6912 3 snd_seq_midi,snd_rawmidi,snd_seq
drm 206161 4 i915,drm_kms_helper
snd 64117 13 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
uvcvideo 62379 0
cfg80211 170293 2 rt2x00lib,mac80211
soundcore 1240 1 snd
i2c_algo_bit 6208 1 i915
psmouse 62080 0
snd_page_alloc 8588 2 snd_hda_intel,snd_pcm
videodev 49359 1 uvcvideo
btusb 12929 2
v4l1_compat 15519 2 uvcvideo,videodev
eeprom_93cx6 1789 1 rt2800pci
v4l2_compat_ioctl32 12646 1 videodev
video 22176 1 i915
serio_raw 4910 0
bluetooth 59213 9 rfcomm,sco,bnep,l2cap,btusb
intel_agp 32080 2 i915
lp 10201 0
hp_wmi 6435 0
output 2527 1 video
parport 37032 3 parport_pc,ppdev,lp
ahci 21857 0
r8169 42222 0
libahci 26167 2 ahci
mii 5261 1 r8169

[the_eye]

Αν θες αντικατέστησε το lpci -n με την lpci -nn

[idomeneas]

Μολονότι πρέπει να ζητηθεί το lspci -nn η κάρτα ασυρμάτου είναι η

Κώδικας: Επιλογή όλων

02:00.0 0280: 1814:3090

Κανονικά θα έπρεπε να μπει ο RT3090sta. Φαίνεται ότι φορτώνεται και ο RT2860sta με τον RT2800pci οπότε ίσως αν δοκίμαζες να κάνεις blacklist τον rt2800pci να λυνόταν το πρόβλημα.