δεν βλεπει το dvdrw

[argy1]

το προβλημα ειναι αυτο που αναφερω στον τιτλο. εψαξα στο φορουμ μηπως με βοηθησει καποιο παλαιοτερο ποστ χωρις ομψς αποτελεσμα. στις τοποθεσιες το δειχνει αλλα στις ιδιοτητες γραφει αγνωστος τυπος και δεν παιζει κανενα cd-dvd. επισης οταν παω να γραξω κατι σε cd-dvd μου λεει συνεχεια βαλτε ενα αδειο μεσο (μην ρωτησετε, ενοειται πως ειναι αδειο )

[Th P]

Καλησπέρα
δές εδώ σε ένα πρόβλημα που είχα παλιότερα: viewtopic.php?f=16&t=16132

Φιλικά
Θανάσης Π.

[argy1]

πρεπει δηλαδη να αναβαθμισω το udev? και αν ναι υπαρχει καποιος οδηγος?

[argy1]

Ρε παιδια βοηθηστε με λιγο. τι πρεπει να κανω?

[vagrale13]

Δωσε μας και τα αποτελεσματα των εντολων

Κώδικας: Επιλογή όλων

dmesg
sudo /sbin/hdparm -I /dev/sr*
cat /etc/fstab

[argy1]

Κώδικας: Επιλογή όλων

[ 0.352960] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.353046] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.353131] ACPI: PCI Interrupt Link [LNK6] (IRQs *5 7 9 10 11 14 15)
[ 0.353217] ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.353300] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.353387] ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.353471] ACPI: PCI Interrupt Link [LIGP] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.353556] ACPI: PCI Interrupt Link [LUBA] (IRQs *5 7 9 10 11 14 15)
[ 0.353651] ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 *10 11 14 15)
[ 0.353738] ACPI: PCI Interrupt Link [LU1B] (IRQs 5 7 9 10 11 14 15) *0
[ 0.353823] ACPI: PCI Interrupt Link [LU2B] (IRQs 5 7 9 10 11 14 15) *0
[ 0.353907] ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 11 14 *15)
[ 0.353993] ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15)
[ 0.354081] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.354165] ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 *11 14 15)
[ 0.354248] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.354332] ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
[ 0.354447] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
[ 0.354560] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
[ 0.354665] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
[ 0.354773] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
[ 0.354879] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
[ 0.354986] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0
[ 0.355094] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
[ 0.355209] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
[ 0.355314] ACPI: PCI Interrupt Link [AIGP] (IRQs 20 21 22 23) *0, disabled.
[ 0.355422] ACPI: PCI Interrupt Link [AUBA] (IRQs 20 21 22 23) *0
[ 0.355535] ACPI: PCI Interrupt Link [AUB2] (IRQs 20 21 22 23) *0
[ 0.355642] ACPI: PCI Interrupt Link [AU1B] (IRQs 20 21 22 23) *0
[ 0.355752] ACPI: PCI Interrupt Link [AU2B] (IRQs 20 21 22 23) *0
[ 0.355863] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
[ 0.355969] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
[ 0.356078] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
[ 0.356184] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
[ 0.356290] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
[ 0.356402] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[ 0.356508] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
[ 0.356613] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.356615] vgaarb: loaded
[ 0.356717] SCSI subsystem initialized
[ 0.356824] libata version 3.00 loaded.
[ 0.356878] usbcore: registered new interface driver usbfs
[ 0.356886] usbcore: registered new interface driver hub
[ 0.356904] usbcore: registered new device driver usb
[ 0.357023] ACPI: WMI: Mapper loaded
[ 0.357024] PCI: Using ACPI for IRQ routing
[ 0.357188] NetLabel: Initializing
[ 0.357190] NetLabel: domain hash size = 128
[ 0.357191] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.357202] NetLabel: unlabeled traffic allowed by default
[ 0.357226] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.357231] hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
[ 0.357234] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[ 0.360098] Switching to clocksource tsc
[ 0.361382] AppArmor: AppArmor Filesystem Enabled
[ 0.361397] pnp: PnP ACPI init
[ 0.361412] ACPI: bus type pnp registered
[ 0.364076] pnp: PnP ACPI: found 12 devices
[ 0.364078] ACPI: ACPI bus type pnp unregistered
[ 0.364088] system 00:01: ioport range 0x1000-0x107f has been reserved
[ 0.364089] system 00:01: ioport range 0x1080-0x10ff has been reserved
[ 0.364091] system 00:01: ioport range 0x1400-0x147f has been reserved
[ 0.364093] system 00:01: ioport range 0x1480-0x14ff has been reserved
[ 0.364095] system 00:01: ioport range 0x1800-0x187f has been reserved
[ 0.364097] system 00:01: ioport range 0x1880-0x18ff has been reserved
[ 0.364099] system 00:01: iomem range 0xfefe0000-0xfefe01ff has been reserved
[ 0.364101] system 00:01: iomem range 0xfefe1000-0xfefe10ff has been reserved
[ 0.364105] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 0.364106] system 00:02: ioport range 0x800-0x87f has been reserved
[ 0.364108] system 00:02: ioport range 0x295-0x314 has been reserved
[ 0.364110] system 00:02: ioport range 0x290-0x294 has been reserved
[ 0.364112] system 00:02: ioport range 0x880-0x88f has been reserved
[ 0.364119] system 00:0a: iomem range 0xe4000000-0xe5ffffff has been reserved
[ 0.364122] system 00:0b: iomem range 0xcd400-0xcffff has been reserved
[ 0.364124] system 00:0b: iomem range 0xf0000-0xf7fff could not be reserved
[ 0.364126] system 00:0b: iomem range 0xf8000-0xfbfff could not be reserved
[ 0.364128] system 00:0b: iomem range 0xfc000-0xfffff could not be reserved
[ 0.364130] system 00:0b: iomem range 0xcfee0000-0xcfefffff could not be reserved
[ 0.364132] system 00:0b: iomem range 0xffff0000-0xffffffff has been reserved
[ 0.364133] system 00:0b: iomem range 0x0-0x9ffff could not be reserved
[ 0.364135] system 00:0b: iomem range 0x100000-0xcfedffff could not be reserved
[ 0.364137] system 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.364139] system 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.364141] system 00:0b: iomem range 0xfeff0000-0xfeff03ff has been reserved
[ 0.368805] pci 0000:00:0a.0: PCI bridge, secondary bus 0000:01
[ 0.368808] pci 0000:00:0a.0: IO window: 0xa000-0xafff
[ 0.368811] pci 0000:00:0a.0: MEM window: disabled
[ 0.368813] pci 0000:00:0a.0: PREFETCH window: disabled
[ 0.368819] pci 0000:00:0b.0: PCI bridge, secondary bus 0000:02
[ 0.368821] pci 0000:00:0b.0: IO window: 0xb000-0xbfff
[ 0.368823] pci 0000:00:0b.0: MEM window: 0xe0000000-0xe3ffffff
[ 0.368826] pci 0000:00:0b.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
[ 0.368835] pci 0000:00:0a.0: setting latency timer to 64
[ 0.368839] pci 0000:00:0b.0: setting latency timer to 64
[ 0.368842] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.368844] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.368845] pci_bus 0000:01: resource 0 io: [0xa000-0xafff]
[ 0.368847] pci_bus 0000:01: resource 3 io: [0x00-0xffff]
[ 0.368848] pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.368850] pci_bus 0000:02: resource 0 io: [0xb000-0xbfff]
[ 0.368851] pci_bus 0000:02: resource 1 mem: [0xe0000000-0xe3ffffff]
[ 0.368853] pci_bus 0000:02: resource 2 pref mem [0xd0000000-0xdfffffff]
[ 0.368889] NET: Registered protocol family 2
[ 0.369024] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.370272] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 0.376765] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.377590] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.377593] TCP reno registered
[ 0.377757] NET: Registered protocol family 1
[ 0.409657] pci 0000:02:00.0: Boot video device
[ 0.409875] Scanning for low memory corruption every 60 seconds
[ 0.410032] audit: initializing netlink socket (disabled)
[ 0.410047] type=2000 audit(1312993007.409:1): initialized
[ 0.416497] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.417448] VFS: Disk quotas dquot_6.5.2
[ 0.417486] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.417900] fuse init (API version 7.13)
[ 0.417951] msgmni has been set to 7906
[ 0.418117] alg: No test for stdrng (krng)
[ 0.418152] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.418155] io scheduler noop registered
[ 0.418156] io scheduler anticipatory registered
[ 0.418157] io scheduler deadline registered
[ 0.418182] io scheduler cfq registered (default)
[ 0.418286] alloc irq_desc for 24 on node -1
[ 0.418287] alloc kstat_irqs on node -1
[ 0.418296] pcieport 0000:00:0b.0: irq 24 for MSI/MSI-X
[ 0.418303] pcieport 0000:00:0b.0: setting latency timer to 64
[ 0.418351] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.418365] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.418451] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.418454] ACPI: Power Button [PWRB]
[ 0.418495] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.418497] ACPI: Power Button [PWRF]
[ 0.418767] processor LNXCPU:00: registered as cooling_device0
[ 0.418795] processor LNXCPU:01: registered as cooling_device1
[ 0.421904] Linux agpgart interface v0.103
[ 0.421929] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.422020] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.422254] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.422949] brd: module loaded
[ 0.423270] loop: module loaded
[ 0.423319] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 0.423437] pata_acpi 0000:00:08.0: setting latency timer to 64
[ 0.423645] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
[ 0.423649] alloc irq_desc for 23 on node -1
[ 0.423650] alloc kstat_irqs on node -1
[ 0.423656] pata_acpi 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23
[ 0.423678] pata_acpi 0000:00:0e.0: setting latency timer to 64
[ 0.423683] pata_acpi 0000:00:0e.0: PCI INT A disabled
[ 0.423863] Fixed MDIO Bus: probed
[ 0.423890] PPP generic driver version 2.4.2
[ 0.423910] tun: Universal TUN/TAP device driver, 1.6
[ 0.423911] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.423966] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.424144] ACPI: PCI Interrupt Link [AUB2] enabled at IRQ 22
[ 0.424146] alloc irq_desc for 22 on node -1
[ 0.424147] alloc kstat_irqs on node -1
[ 0.424150] ehci_hcd 0000:00:04.1: PCI INT B -> Link[AUB2] -> GSI 22 (level, low) -> IRQ 22
[ 0.424162] ehci_hcd 0000:00:04.1: setting latency timer to 64
[ 0.424164] ehci_hcd 0000:00:04.1: EHCI Host Controller
[ 0.424187] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
[ 0.424212] ehci_hcd 0000:00:04.1: debug port 1
[ 0.424218] ehci_hcd 0000:00:04.1: cache line size of 32 is not supported
[ 0.424231] ehci_hcd 0000:00:04.1: irq 22, io mem 0xe6007000
[ 0.431534] Freeing initrd memory: 8174k freed
[ 0.439635] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00
[ 0.439846] usb usb1: configuration #1 chosen from 1 choice
[ 0.439869] hub 1-0:1.0: USB hub found
[ 0.439879] hub 1-0:1.0: 10 ports detected
[ 0.439941] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.440200] ACPI: PCI Interrupt Link [AUBA] enabled at IRQ 21
[ 0.440206] alloc irq_desc for 21 on node -1
[ 0.440207] alloc kstat_irqs on node -1
[ 0.440214] ohci_hcd 0000:00:04.0: PCI INT A -> Link[AUBA] -> GSI 21 (level, low) -> IRQ 21
[ 0.440245] ohci_hcd 0000:00:04.0: setting latency timer to 64
[ 0.440247] ohci_hcd 0000:00:04.0: OHCI Host Controller
[ 0.440283] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
[ 0.440311] ohci_hcd 0000:00:04.0: irq 21, io mem 0xe6006000
[ 0.501663] usb usb2: configuration #1 chosen from 1 choice
[ 0.501678] hub 2-0:1.0: USB hub found
[ 0.501684] hub 2-0:1.0: 10 ports detected
[ 0.501723] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.501800] PNP: No PS/2 controller found. Probing ports directly.
[ 0.502210] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.502216] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.502294] mice: PS/2 mouse device common for all mice
[ 0.502378] rtc_cmos 00:05: RTC can wake from S4
[ 0.502416] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 0.502447] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
[ 0.502532] device-mapper: uevent: version 1.0.3
[ 0.502645] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.502699] device-mapper: multipath: version 1.1.0 loaded
[ 0.502701] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.502818] cpuidle: using governor ladder
[ 0.502820] cpuidle: using governor menu
[ 0.503085] TCP cubic registered
[ 0.503188] NET: Registered protocol family 10
[ 0.503681] NET: Registered protocol family 17
[ 0.503766] PM: Resume from disk failed.
[ 0.503789] registered taskstats version 1
[ 0.504012] Magic number: 7:180:287
[ 0.504038] tty tty20: hash matches
[ 0.504065] acpi PNP0400:00: hash matches
[ 0.504107] rtc_cmos 00:05: setting system clock to 2011-08-10 16:16:48 UTC (1312993008)
[ 0.504109] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.504110] EDD information not available.
[ 0.504149] Freeing unused kernel memory: 888k freed
[ 0.504544] Write protecting the kernel read-only data: 7688k
[ 0.513810] udev: starting version 151
[ 0.553827] pata_amd 0000:00:08.0: version 0.4.1
[ 0.553878] pata_amd 0000:00:08.0: setting latency timer to 64
[ 0.572770] scsi0 : pata_amd
[ 0.580958] scsi1 : pata_amd
[ 0.581432] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 0.581434] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 0.581592] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 0.581801] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 20
[ 0.581806] alloc irq_desc for 20 on node -1
[ 0.581807] alloc kstat_irqs on node -1
[ 0.581814] forcedeth 0000:00:0f.0: PCI INT A -> Link[APCH] -> GSI 20 (level, low) -> IRQ 20
[ 0.581817] forcedeth 0000:00:0f.0: setting latency timer to 64
[ 0.760072] ata1.00: ATAPI: SONY DVD RW DRU-190A, 1.63, max UDMA/66
[ 0.760086] ata1: nv_mode_filter: 0x1f39f&0x1f39f->0x1f39f, BIOS=0x1f000 (0xc5000000) ACPI=0x1f01f (30:600:0x13)
[ 0.800000] ata1.00: configured for UDMA/66
[ 0.801922] scsi 0:0:0:0: CD-ROM SONY DVD RW DRU-190A 1.63 PQ: 0 ANSI: 5
[ 0.807929] sr0: scsi3-mmc drive: 48x/12x writer dvd-ram cd/rw xa/form2 cdda tray
[ 0.807932] Uniform CD-ROM driver Revision: 3.20
[ 0.808021] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 0.808066] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 0.808114] ata2: port disabled. ignoring.
[ 0.879825] usb 1-2: new high speed USB device using ehci_hcd and address 3
[ 1.050575] usb 1-2: configuration #1 chosen from 1 choice
[ 1.055389] Initializing USB Mass Storage driver...
[ 1.055464] scsi2 : SCSI emulation for USB Mass Storage devices
[ 1.055514] usb-storage: device found at 3
[ 1.055516] usb-storage: waiting for device to settle before scanning
[ 1.055523] usbcore: registered new interface driver usb-storage
[ 1.055525] USB Mass Storage support registered.
[ 1.112189] forcedeth 0000:00:0f.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1f:d0:5f:3c:6c
[ 1.112192] forcedeth 0000:00:0f.0: highdma pwrctl mgmt gbit lnktim msi desc-v3
[ 1.112209] ahci 0000:00:0e.0: version 3.0
[ 1.112223] ahci 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23
[ 1.112269] alloc irq_desc for 25 on node -1
[ 1.112270] alloc kstat_irqs on node -1
[ 1.112277] ahci 0000:00:0e.0: irq 25 for MSI/MSI-X
[ 1.112282] ahci 0000:00:0e.0: controller can do NCQ, turning on CAP_NCQ
[ 1.112322] ahci 0000:00:0e.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode
[ 1.112324] ahci 0000:00:0e.0: flags: 64bit ncq sntf led clo pmp pio
[ 1.112327] ahci 0000:00:0e.0: setting latency timer to 64
[ 1.112564] scsi3 : ahci
[ 1.112611] scsi4 : ahci
[ 1.112652] scsi5 : ahci
[ 1.112693] scsi6 : ahci
[ 1.112783] ata3: SATA max UDMA/133 abar m8192@0xe6004000 port 0xe6004100 irq 25
[ 1.112785] ata4: SATA max UDMA/133 abar m8192@0xe6004000 port 0xe6004180 irq 25
[ 1.112786] ata5: SATA max UDMA/133 abar m8192@0xe6004000 port 0xe6004200 irq 25
[ 1.112788] ata6: SATA max UDMA/133 abar m8192@0xe6004000 port 0xe6004280 irq 25
[ 1.460016] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.460039] ata6: SATA link down (SStatus 0 SControl 300)
[ 1.630020] usb 2-1: new full speed USB device using ohci_hcd and address 2
[ 1.640012] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.640021] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.641653] ata5.00: ATA-8: WDC WD10EARS-00Y5B1, 80.00A80, max UDMA/133
[ 1.641656] ata5.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.644143] ata5.00: configured for UDMA/133
[ 1.646308] ata4.00: ATA-7: SAMSUNG HD322HJ, 1AC01112, max UDMA7
[ 1.646311] ata4.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.652670] ata4.00: configured for UDMA/133
[ 1.652750] scsi 4:0:0:0: Direct-Access ATA SAMSUNG HD322HJ 1AC0 PQ: 0 ANSI: 5
[ 1.652855] sd 4:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 1.652857] sd 4:0:0:0: Attached scsi generic sg1 type 0
[ 1.652915] sd 4:0:0:0: [sda] Write Protect is off
[ 1.652917] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.652919] scsi 5:0:0:0: Direct-Access ATA WDC WD10EARS-00Y 80.0 PQ: 0 ANSI: 5
[ 1.652959] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.652980] sd 5:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 1.653010] sd 5:0:0:0: [sdb] Write Protect is off
[ 1.653012] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.653029] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.653083] sda:
[ 1.653132] sdb:
[ 1.653154] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 1.666682] sda1 sda2 sda3 sda4 < sda5 >
[ 1.692232] sd 4:0:0:0: [sda] Attached SCSI disk
[ 1.698473] ldm_parse_tocblock(): Cannot find TOCBLOCK, database may be corrupt.
[ 1.698478] ldm_parse_tocblock(): Cannot find TOCBLOCK, database may be corrupt.
[ 1.733052] [LDM] sdb1
[ 1.733305] sd 5:0:0:0: [sdb] Attached SCSI disk
[ 1.865988] usb 2-1: configuration #1 chosen from 1 choice
[ 1.874698] usbcore: registered new interface driver hiddev
[ 1.881133] input: Razer Razer Abyssus as /devices/pci0000:00/0000:00:04.0/usb2/2-1/2-1:1.0/input/input3
[ 1.881206] generic-usb 0003:1532:001C.0001: input,hidraw0: USB HID v1.11 Mouse [Razer Razer Abyssus] on usb-0000:00:04.0-1/input0
[ 1.881225] usbcore: registered new interface driver usbhid
[ 1.881228] usbhid: v2.6:USB HID core driver
[ 2.092031] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 2.200020] usb 2-4: new full speed USB device using ohci_hcd and address 3
[ 2.437093] usb 2-4: configuration #1 chosen from 1 choice
[ 2.447217] input: Razer Razer Arctosa as /devices/pci0000:00/0000:00:04.0/usb2/2-4/2-4:1.0/input/input4
[ 2.447263] generic-usb 0003:1532:010B.0002: input,hidraw1: USB HID v1.11 Keyboard [Razer Razer Arctosa] on usb-0000:00:04.0-4/input0
[ 2.459083] input: Razer Razer Arctosa as /devices/pci0000:00/0000:00:04.0/usb2/2-4/2-4:1.1/input/input5
[ 2.459116] generic-usb 0003:1532:010B.0003: input,hidraw2: USB HID v1.11 Device [Razer Razer Arctosa] on usb-0000:00:04.0-4/input1
[ 2.791282] usb 2-9: new full speed USB device using ohci_hcd and address 4
[ 3.025209] usb 2-9: configuration #1 chosen from 1 choice
[ 6.050134] usb-storage: device scan complete
[ 6.055236] scsi 2:0:0:0: Direct-Access TOSHIBA USB 3.5"-HDD 100 PQ: 0 ANSI: 2
[ 6.055574] sd 2:0:0:0: Attached scsi generic sg3 type 0
[ 6.056347] sd 2:0:0:0: [sdc] 1250263728 512-byte logical blocks: (640 GB/596 GiB)
[ 6.059471] sd 2:0:0:0: [sdc] Write Protect is off
[ 6.059474] sd 2:0:0:0: [sdc] Mode Sense: 38 00 00 00
[ 6.059476] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 6.063473] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 6.063477] sdc: sdc1
[ 6.079475] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 6.079478] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 14.910404] udev: starting version 151
[ 14.923313] Adding 11885560k swap on /dev/sda5. Priority:-1 extents:1 across:11885560k
[ 14.971133] i2c i2c-0: nForce2 SMBus adapter at 0x1c00
[ 14.971162] i2c i2c-1: nForce2 SMBus adapter at 0x1c80
[ 14.987504] vga16fb: initializing
[ 14.987507] vga16fb: mapped to 0xffff8800000a0000
[ 14.987564] fb0: VGA16 VGA frame buffer device
[ 15.023841] lp: driver loaded but no devices found
[ 15.083452] type=1505 audit(1312982223.075:2): operation="profile_load" pid=569 name="/sbin/dhclient3"
[ 15.083905] type=1505 audit(1312982223.075:3): operation="profile_load" pid=569 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 15.084152] type=1505 audit(1312982223.075:4): operation="profile_load" pid=569 name="/usr/lib/connman/scripts/dhclient-script"
[ 15.117304] type=1505 audit(1312982223.105:5): operation="profile_replace" pid=655 name="/sbin/dhclient3"
[ 15.117769] type=1505 audit(1312982223.105:6): operation="profile_replace" pid=655 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 15.118020] type=1505 audit(1312982223.105:7): operation="profile_replace" pid=655 name="/usr/lib/connman/scripts/dhclient-script"
[ 15.169477] nvidia: module license 'NVIDIA' taints kernel.
[ 15.169480] Disabling lock debugging due to kernel taint
[ 15.255640] type=1505 audit(1312982223.245:8): operation="profile_replace" pid=823 name="/sbin/dhclient3"
[ 15.256118] type=1505 audit(1312982223.245:9): operation="profile_replace" pid=823 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 15.259410] type=1505 audit(1312982223.245:10): operation="profile_load" pid=822 name="/usr/share/gdm/guest-session/Xsession"
[ 15.260140] type=1505 audit(1312982223.255:11): operation="profile_replace" pid=823 name="/usr/lib/connman/scripts/dhclient-script"
[ 15.360983] alloc irq_desc for 26 on node -1
[ 15.360985] alloc kstat_irqs on node -1
[ 15.360992] forcedeth 0000:00:0f.0: irq 26 for MSI/MSI-X
[ 15.594763] Console: switching to colour frame buffer device 80x30
[ 15.617757] parport_pc 00:09: reported by Plug and Play ACPI
[ 15.617799] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 15.630475] Bluetooth: Core ver 2.15
[ 15.630603] NET: Registered protocol family 31
[ 15.630604] Bluetooth: HCI device and connection manager initialized
[ 15.630606] Bluetooth: HCI socket layer initialized
[ 15.631583] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 15.631659] usbcore: registered new interface driver btusb
[ 15.647200] Bluetooth: L2CAP ver 2.14
[ 15.647202] Bluetooth: L2CAP socket layer initialized
[ 15.656619] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 15.656621] Bluetooth: BNEP filters: protocol multicast
[ 15.675867] Bridge firewalling registered
[ 15.688040] it87: Found IT8718F chip at 0x290, revision 5
[ 15.688054] it87: in3 is VCC (+5V)
[ 15.688317] ppdev: user-space parallel port driver
[ 15.690252] lp0: using parport0 (interrupt-driven).
[ 15.691800] ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16
[ 15.691806] alloc irq_desc for 16 on node -1
[ 15.691808] alloc kstat_irqs on node -1
[ 15.691814] nvidia 0000:02:00.0: PCI INT A -> Link[APC6] -> GSI 16 (level, low) -> IRQ 16
[ 15.691821] nvidia 0000:02:00.0: setting latency timer to 64
[ 15.691825] vgaarb: device changed decodes: PCI:0000:02:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 15.692387] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 195.36.24 Thu Apr 22 19:10:14 PDT 2010
[ 15.702712] Bluetooth: SCO (Voice Link) ver 0.6
[ 15.702714] Bluetooth: SCO socket layer initialized
[ 15.727120] HDA Intel 0000:00:09.0: power state changed by ACPI to D0
[ 15.727144] HDA Intel 0000:00:09.0: power state changed by ACPI to D0
[ 15.727372] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
[ 15.727376] HDA Intel 0000:00:09.0: PCI INT A -> Link[AAZA] -> GSI 23 (level, low) -> IRQ 23
[ 15.727379] hda_intel: Disable MSI for Nvidia chipset
[ 15.727491] HDA Intel 0000:00:09.0: setting latency timer to 64
[ 15.810522] Bluetooth: RFCOMM TTY layer initialized
[ 15.810525] Bluetooth: RFCOMM socket layer initialized
[ 15.810527] Bluetooth: RFCOMM ver 1.11
[ 16.749506] vboxdrv: Found 2 processor cores.
[ 16.749607] VBoxDrv: dbg - g_abExecMemory=ffffffffa0d78a40
[ 16.749608] vboxdrv: fAsync=0 offMin=0x198 offMax=0x6cb
[ 16.749919] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 16.749921] vboxdrv: Successfully loaded version 4.0.8 (interface 0x00180000).
[ 17.159323] CPU0 attaching NULL sched-domain.
[ 17.159328] CPU1 attaching NULL sched-domain.
[ 17.210081] CPU0 attaching sched-domain:
[ 17.210088] domain 0: span 0-1 level MC
[ 17.210090] groups: 0 1
[ 17.210094] CPU1 attaching sched-domain:
[ 17.210095] domain 0: span 0-1 level MC
[ 17.210097] groups: 1 0
[ 17.301370] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:09.0/input/input6
[ 20.617591] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 20.773313] CPU0 attaching NULL sched-domain.
[ 20.773318] CPU1 attaching NULL sched-domain.
[ 20.820083] CPU0 attaching sched-domain:
[ 20.820086] domain 0: span 0-1 level MC
[ 20.820088] groups: 0 1
[ 20.820092] CPU1 attaching sched-domain:
[ 20.820093] domain 0: span 0-1 level MC
[ 20.820095] groups: 1 0
[ 26.060010] eth0: no IPv6 routers present
[ 6564.314284] process `skype' is using obsolete setsockopt SO_BSDCOMPAT
argy@argy-desktop:~$ sudo /sbin/hdparm -I /dev/sr*

/dev/sr0:

ATAPI CD-ROM, with removable media
Model Number: SONY DVD RW DRU-190A
Serial Number:
Firmware Revision: 1.63
Standards:
Likely used CD-ROM ATAPI-1
Configuration:
DRQ response: 50us.
Packet size: 12 bytes
cache/buffer size = unknown
Capabilities:
LBA, IORDY(cannot be disabled)
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* PACKET command feature set
* DEVICE_RESET command
* Mandatory FLUSH_CACHE
HW reset results:
CBLID- above Vih
Device num = 0
argy@argy-desktop:~$ cat /etc/fstab
# /etc/fstab: static file system information.
#
# Use 'blkid -o value -s UUID' to print the universally unique identifier
# for a device; this may be used with UUID= as a more robust way to name
# devices that works even if disks are added and removed. See fstab(5).
#
# <file system> <mount point> <type> <options> <dump> <pass>
proc /proc proc nodev,noexec,nosuid 0 0
/dev/sda1 / ext4 errors=remount-ro 0 1
/dev/sda5 none swap sw 0 0


[vagrale13]

Τη συσκευη σου τη βλεπει, και ειναι αυτη SONY - DVD RW DRU-190A σωστα?
Τωρα, δες κατι παρομοιο εδω http://ubuntuforums.org/showthread.php?t=1612267
στο τελεος λεει οτι βρηκε λυση, προσθετοντας στον πυρηνα την παραμετρο libata.dma=1
Καλο ειναι να το δοκιμασεις πρωτα, χωρις να το κανεις μονιμο, για να σιγουρευτεις οτι δεν θα δημιουργηθει καποιο αλλο προβλημα και οτι μετα θα ειναι οκ.
Δες τον τροπο εδω https://help.ubuntu.com/community/Grub2 ... ing%20Boot

Δηλαδη... θα κανεις επανεκκινηση, θα κρατησεις πατημενο το πληκτρο SHIFT για να βγεις στο menu του grub, θα επιλεξεις τον νεοτερο πυρηνα,
θα πατησεις το πληκτρο C και θα σου εμφανησει εδω

με τα βελακια θα πας στην προτελευταια γραμμη, και στο τελος αυτης θα γραψεις την παραπανω παραμετρο.
δηλαδη να ειναι καπως ετσι

Κώδικας: Επιλογή όλων

linux /boot/vmlinuz-2.6.38-11 root=UUID=904bf39-9234 ro quiet splash libata.dma=1

Μετα θα πατησεις ττον συνδιασμο των πληκτρων CTRL-X
και οταν θα μπεις στο συστημα, δες αν ειναι ενταξει η συσκευη που εχεις!

[argy1]

Δεν μπορω να εμφανισω το μενου αυτο με τιποτα. πατωντας το shift δεν κανει τιποτα, μονο με το c μου εμφανιζει ενα παραθυρο που λεει:gnu grub version 1.98 minimal bash-like line editing is supported... ειναι error?

[vagrale13]

Την εγκατασταση του Ubuntu με ποιον τροπο την εχεις κανει, κανονικα ή μεσα απο τα παραθυρα με το wubi ?
Δες πως ειναι η κανονικη εγκατασταση viewtopic.php?f=9&t=8535
και πως ειναι με το wubi viewtopic.php?f=9&t=8185

[argy1]

Αν δεν βαριεσαι δες αυτο το προβλημα που ειχα και θα καταλαβεις τι εκανα. http://forum.ubuntu-gr.org/viewtopic.php?f=4&t=19091