Έλεγχος σκληρού δίσκου Hardware

[ΝΙΚΟΛΑΟΣ]

Έτρεξα memtest και μου έδωσε αυτά τα αποτελέσματα
http://imagebin.ubuntu-gr.org/files2017/1566285509.png

[the_eye]

Μετά πρέπει να κάνεις harware ελέγχους πχ να μετρήσεις το τροφοδοτικό, να κάνεις ένα οπτικό έλεγχο στην μητρική και χαλασμένους πυκνωτές, κτλ κτλ

[ΝΙΚΟΛΑΟΣ]

Ευχαριστώ. Αυτό θέλει αρκετό χρόνο και πρέπει να αγοράσω πολύμετρo. Μετά τις διακοπές.

[dgtfeargr]

Κώδικας: Επιλογή όλων

invisible@invisible-Aspire-7736:~$ sudo smartctl -a /dev/sda
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-166-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model: Patriot Burst
Serial Number: A472078C043000471109
Firmware Version: SBFM61.3
User Capacity: 480.103.981.056 bytes [480 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: Unknown(0x0ff8) (minor revision not indicated)
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Oct 26 22:40:39 2019 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (65535) seconds.
Offline data collection
capabilities: (0x79) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 30) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 2870
12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 608
168 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 0
170 Unknown_Attribute 0x0003 065 065 010 Pre-fail Always - 222
173 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 655391
192 Power-Off_Retract_Count 0x0012 100 100 000 Old_age Always - 21
194 Temperature_Celsius 0x0023 067 067 000 Pre-fail Always - 33 (Min/Max 33/33)
218 Unknown_Attribute 0x000b 100 100 050 Pre-fail Always - 0
231 Temperature_Celsius 0x0013 100 100 000 Pre-fail Always - 99
241 Total_LBAs_Written 0x0012 100 100 000 Old_age Always - 3586

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

invisible@invisible-Aspire-7736:~$ sudo smartctl -a /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-166-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA
Device Model: WDC WD5000BEVT-22ZAT0
Serial Number: WD-WXQ0A99J4715
LU WWN Device Id: 5 0014ee 2039148a1
Firmware Version: 01.01A01
User Capacity: 500.107.862.016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat Oct 26 22:41:39 2019 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (13200) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 154) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 5449
3 Spin_Up_Time 0x0027 186 174 021 Pre-fail Always - 1700
4 Start_Stop_Count 0x0032 088 088 000 Old_age Always - 12297
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 065 065 000 Old_age Always - 26119
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 091 091 000 Old_age Always - 9661
192 Power-Off_Retract_Count 0x0032 199 199 000 Old_age Always - 1191
193 Load_Cycle_Count 0x0032 117 117 000 Old_age Always - 250703
194 Temperature_Celsius 0x0022 113 080 000 Old_age Always - 34
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0

SMART Error Log Version: 1
Warning: ATA error count 12310 inconsistent with error log pointer 1

ATA Error Count: 12310 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 12310 occurred at disk power-on lifetime: 22609 hours (942 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 10 00 00 00 40 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c6 00 10 00 00 00 00 00 00:43:11.734 SET MULTIPLE MODE
ec 00 00 00 00 00 00 00 00:43:11.733 IDENTIFY DEVICE
ef 02 00 00 00 00 00 00 00:43:08.587 SET FEATURES [Enable write cache]
ef 03 46 00 00 00 00 00 00:43:08.509 SET FEATURES [Set transfer mode]

Error 12309 occurred at disk power-on lifetime: 22609 hours (942 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 00 00 00 00 40 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 02 00 00 00 00 00 00 00:43:08.587 SET FEATURES [Enable write cache]
ef 03 46 00 00 00 00 00 00:43:08.509 SET FEATURES [Set transfer mode]
c6 00 10 00 00 00 00 00 00:43:08.375 SET MULTIPLE MODE

Error 12308 occurred at disk power-on lifetime: 22609 hours (942 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 40 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 00 00 00:43:08.509 SET FEATURES [Set transfer mode]
c6 00 10 00 00 00 00 00 00:43:08.375 SET MULTIPLE MODE
ef 02 00 00 00 00 00 00 00:43:07.889 SET FEATURES [Enable write cache]

Error 12307 occurred at disk power-on lifetime: 22609 hours (942 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 10 00 00 00 40 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c6 00 10 00 00 00 00 00 00:43:08.375 SET MULTIPLE MODE
ef 02 00 00 00 00 00 00 00:43:07.889 SET FEATURES [Enable write cache]
ef 03 46 00 00 00 00 00 00:43:07.811 SET FEATURES [Set transfer mode]

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

invisible@invisible-Aspire-7736:~$


[the_eye]

Ναι, έχει πρόβλημα

Κώδικας: Επιλογή όλων

1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 5449

Κώδικας: Επιλογή όλων

SMART Error Log Version: 1
Warning: ATA error count 12310 inconsistent with error log pointer 1

[dgtfeargr]

Ναι, έχει πρόβλημα

Κώδικας: Επιλογή όλων

1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 5449

Κώδικας: Επιλογή όλων

SMART Error Log Version: 1
Warning: ATA error count 12310 inconsistent with error log pointer 1

10 ετών σκληρός φορητού υπολογιστή, τα έφαγε τα ψωμάκια του

[joe iwannou]

Κώδικας: Επιλογή όλων

A B
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 119 099 006 Pre-fail Always - 225047536 154471120
3 Spin_Up_Time 0x0003 098 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 2021 1547
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 262701864 41911237
9 Power_On_Hours 0x0032 080 080 000 Old_age Always - 18094 10789
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always - 2055 1806
183 Runtime_Bad_Block 0x0000 100 100 000 Old_age Offline - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 662
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 073 054 045 Old_age Always - 27 (Min/Max 17/27)
194 Temperature_Celsius 0x0022 027 046 000 Old_age Always - 27 (0 13 0 0 0)
195 Hardware_ECC_Recovered 0x001a 062 044 000 Old_age Always - 225047536
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 23550 (172 199 0) 11519h+42m+46.834s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2757098482 8282180047
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 692458144 66937135246



Ποιος είναι καλύτερός ;

[the_eye]

Έχουν πρόβλημα και οι 2.
Δεν νομίζω ότι υπάρχει καλύτερος ανάμεσα σε 2 χαλασμένους δίσκους.

[joe iwannou]

Κώδικας: Επιλογή όλων

ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 10
12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 13
168 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 0
170 Unknown_Attribute 0x0003 100 100 010 Pre-fail Always - 82
173 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 1
192 Power-Off_Retract_Count 0x0012 100 100 000 Old_age Always - 7
194 Temperature_Celsius 0x0023 067 067 000 Pre-fail Always - 33 (Min/Max 33/33)
218 Unknown_Attribute 0x000b 100 100 050 Pre-fail Always - 0
231 Temperature_Celsius 0x0013 100 100 000 Pre-fail Always - 100
241 Total_LBAs_Written 0x0012 100 100 000 Old_age Always - 44


Φαίνεται καλός.

[the_eye]

Αγόρασες καινούριο ; 10 ώρες λειτουργία !

Κώδικας: Επιλογή όλων

9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 10

Τι δίσκος είναι ; Μου κάνει εντύπωση γιατί έχει πολλά Unknown_Attribute, για δώσε όλο το αποτέλεσμα της εντολής.